Upload
phamminh
View
217
Download
0
Embed Size (px)
Citation preview
SDVB Serial kit for CC-LINK1 to 8 stations(16 stations)
Serial unit: EX126
IP67 compliant
VV5QC 4 1 08 02
4 VQC4000
Series
TD0
1 Plug-in unit
Manifold model
Stations
VV5QC 4 1 16 03 SDQWOption
Kit Designation/Electrical Entry/Cable Length
Input block (Fill out for I/O unit only)
Input block type (Fill out for I/O unit only)
Cylinder port size
F L M⋅⋅⋅⋅⋅⋅Kit
S⋅⋅⋅⋅⋅⋅ Kit
P T/ //
S Kit(I/O serial transmission kit)
SD0WSDQWSDNW
Serial kit without SI unit Serial kit for DeviceNetSerial kit for PROFIBUS-DP
1 to 12 stations(16 stations)
Serial unit: EX240
S Kit (I/O serial kit)
Serial unit: EX250
Serial unit: EX500
S Kit(Decentralized wiring type serial kit)
SD0SDA1SDA2
Serial kit without SI unit Serial kit for Remote I/OSerial kit for DeviceNet/PROFIBUS-DP/CC-LINK
1 to 8 stations(16 stations)
How to Order Manifold
C8C10C120203B
CM
With ø8 One-touch fittingWith ø10 One-touch fittingWith ø12 One-touch fittingRc 1/4Rc 3/8Bottom ported Rc 1/4Mixed
Note 1) Indicate the size in the specification order sheet in the case of “CM”.
Note 2) Symbols for inch sizes are as follows: <For One-touch fittings>
N7: ø1/4"N9: ø5/16"N11: ø3/8"NM: Mixed
NilKN
NoneSpecial wiring specifications (except for double wiring) Note 1)
With name plate (available for T kit only) Note 2)
Note 1) Be sure to indicate the wiring specifica-tions on the specification order sheet.
Note 2) The mounting position of the name plate is on the top face of the cover for the terminal block box.
∗ When specifying more than one option, enter symbols in alphabetical order. Example: -KN
IP67 compliant
IP67 compliant
IP65 compliant
SI unit COM.
NilDeviceNet
—
PROFIBUS-DP—
DeviceNet—
PROFIBUS-DP—
CC-LINK—
EX500EX240 EX126DeviceNet
PROFIBUS-DP
CC-LINK
Remote I/O
CC-LINK—
SI unit COM
+COM–COMN
Note) Leave the box blank for the SI unit COM. without SI unit (SD0).
Note)Max. 4 for EX240 and max 8 for EX250.
S Kit(Serial output kit)
Input block COM. (Fill out for I/O unit only)Nil PNP (+) or without SI unit/input block
NPN (–)N
AS-i—
SD0SDYSDQSDNSDVSDTASDTBSDTCSDTD
Serial kit without SI unitSerial kit for CANopenSerial kit for DeviceNet Serial kit for PROFIBUS-DPSerial kit for CC-LINKAS-i, 8 in/out, 31 slave modes, 2 power supply systemsAS-i, 4 in/out, 31 slave modes, 2 power supply systemsAS-i, 8 in/out, 31 slave modes, 1 power supply systemsAS-i, 4 in/out, 31 slave modes, 1 power supply systems
1 to 12 stations(24 stations)
1 to 4 stations (8 stations)1 to 2 stations (4 stations)1 to 4 stations (8 stations)1 to 2 stations (4 stations)
CANopen—
01 1 station
The maximum number of stations differs depending on the electrical entry.
Nil Without SI unit/input block (SD0(W))Without input blockWith 1 input block
With 8 input blocks
01
8
⋅⋅⋅ ⋅⋅⋅
Nil Without input blockM12, 8 inputs (EX240)M12, 2 inputs (EX250)M12, 4 inputs (EX250)M8, 4 inputs (EX250)
0123
Plug-in Unit
Series VQC4000Base Mounted
For details about certified products conforming to international standards, visit us at www.smcworld.com.
EX250
2-2-19
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
TD0 Terminal block box kit 1 to 10 stations (16 stations)
Kit Designation/Electrical Entry/Cable Length
T Kit(Terminal block box kit)
LD0LD1LD2
Lead wire kit 0.6 m lead wireLead wire kit 1.5 m lead wireLead wire kit 3.0 m lead wire
1 to 12 stations(16 stations)
PD0PD1PD2PD3
PDC
Flat ribbon cable kit (26P) without cableFlat ribbon cable kit (26P) with 1.5 m cableFlat ribbon cable kit (26P) with 3.0 m cableFlat ribbon cable kit (26P) with 5.0 m cable
Flat ribbon cable kit (20P) without cable Note)
1 to 12 stations(16 stations)
1 to 9 stations(16 stations)
F
L
Kit(D-sub connector kit)
Kit(Lead wire kit)
M
P
Kit(Multiple connector kit)
Kit(Flat ribbon cable kit)
FD0FD1FD2FD3
D-sub connector kit (25P) without cableD-sub connector kit (25P) with 1.5 m cableD-sub connector kit (25P) with 3.0 m cableD-sub connector kit (25P) with 5.0 m cable
1 to 12 stations(16 stations)
MD0MD1MD2MD3
Multiple connector kit (26P) without cableMultiple connector kit (26P) with 1.5 m cableMultiple connector kit (26P) with 3.0 m cableMultiple connector kit (26P) with 5.0 m cable
1 to 12 stations(16 stations)
Note) P kit: when using the flat ribbon cable kit (20P), order cable assemblies separately.
Note) For a 20P flat ribbon cable, the cable assembly must be ordered separately.
IP67 compliant
IP67 compliant
IP67 compliant
IP40 compliant
IP40 compliant
4 VQC4000
Series
Type of actuation
VQC 4 1 0 5
Coil voltage
Manual override
Seal type
Function
Light/Surge voltage suppressor
2 position single
2 position double (metal)
2 position double (rubber)
3 position closed center
1
2
3
WithWithout light, with surge voltage supressor
Nil
E
24 VDC Note)
12 VDC56
3 position exhaust center
3 position pressure center
3 position perfect
4
5
6
0
How to Order Valves
Nil: Non-lockingpush type
(Slotted)
B: Locking type(Slotted)
∗ When specifying more than one option, enter symbols in alphabetical order.
Standard type (1 W)External pilotLow wattage type (0.5 W)
NilRY
Metal sealRubber seal
01
5(R1)
3(R2)
1(P)
5(R1)
3(R2)
1(P)
5(R1)
3(R2)
1(P)
5(R1)
3(R2)
1(P)
5(R1)
3(R2)
1(P)
5(R1)
3(R2)
1(P)
5(R1)
3(R2)
1(P)
(A)4
(B)2
(A)4
(B)2
(A)4
(B)2
(A)4
(B)2
(A)4
(B)2
(A)4
(B)2
(A)4
(B)2
Note) S kit is only available for 24 VDC.
2-2-20
Series VQC4000Base Mounted
LOCK
PUSH
Manifold Option
0203
Blanking plate assemblyVVQ4000-10A-1
Individual SUP spacerVVQ4000-P-1- 02
03
Individual EXH spacerVVQ4000-R-1-
SUP/EXH block plateVVQ4000-16A
Throttle valve spacerVVQ4000-20A-1
Residual pressure release valveperfect spacerVVQ4000-25A-1 Note 1)
SUP stop valve spacerVVQ4000-37A-1
Interface regulatorARBQ4000-00- -1
ABP
Note 1) Perfect spacers with residual pressure release valve cannot be combined with external pilot specifications.
<EXH block plate>
<SUP block plate>
2-2-21
Series VQC4000Plug-in Unit
Base Mounted
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
Ser
ies
No. of solenoids
VQ
C10
00
ModelResponse time (ms)
Note 2)
Weight(g)Standard:
1 WLow
wattage
Metal seal
Rubber seal
Metal seal
Rubber seal
Metal seal
Rubber seal
Metal seal
Rubber seal
Metal seal
Rubber seal
SingleVQC1100
VQC1101
VQC1200
VQC1201
VQC1300
VQC1301
VQC1400
VQC1401
VQC1500
VQC1501
Double
Closedcenter
Exhaustcenter
Pressurecenter
Dual3 port valve
0.70
0.85
0.70
0.85
0.68
0.70
0.68
0.70
0.70
0.85
0.70
2.0
2.2
2.0
2.2
2.0
2.0
2.0
2.0
2.4
3.2
1.8
6.2
7.2
6.2
7.2
5.9
7.0
6.2
7.0
6.2
7.0
2.7
2.8
0.72
1.0
0.72
1.0
0.72
0.65
0.72
1.0
0.72
0.65
0.70
2.6
3.2
2.6
3.2
2.0
2.2
2.6
3.2
2.0
2.2
1.8
6.9
7.3
6.9
7.3
6.3
6.4
6.9
7.3
6.4
7.1
3.7
3.9
12 or less
15 or less
10 or less
15 or less
20 or less
25 or less
20 or less
25 or less
20 or less
25 or less
15 or less
20 or less
13 or less
20 or less
26 or less
33 or less
26 or less
33 or less
26 or less
33 or less
64
78
90
110VQ
C20
00
Metal seal
Rubber seal
Metal seal
Rubber seal
Metal seal
Rubber seal
Metal seal
Rubber seal
Metal seal
Rubber seal
Rubber seal
SingleVQC2100
VQC2101
VQC2200
VQC2201
VQC2300
VQC2301
VQC2400
VQC2401
VQC2500
VQC2501
VQC1 01
Double
Closedcenter
Exhaustcenter
Pressurecenter
2 po
sitio
n3
posi
tion
22 or less
24 or less
15 or less
20 or less
29 or less
34 or less
29 or less
34 or less
29 or less
34 or less
25 or less 33 or less
29 or less
31 or less
20 or less
26 or less
38 or less
44 or less
38 or less
44 or less
38 or less
44 or less
VQ
C40
00
Metal seal
Rubber seal
Metal seal
Rubber seal
Metal seal
Rubber seal
Metal seal
Rubber seal
Metal seal
Rubber seal
Metal seal
Rubber seal
Single
Perfect
VQC4100
VQC4101
VQC4200
VQC4201
VQC4300
VQC4301
VQC4400
VQC4401
VQC4500
VQC4501
VQC4600
VQC4601
Double
Closedcenter
Exhaustcenter
Pressurecenter
2 po
sitio
n3
posi
tion
20 or less
25 or less
12 or less
15 or less
45 or less
50 or less
45 or less
50 or less
45 or less
50 or less
55 or less
62 or less
22 or less
27 or less
12 or less
15 or less
47 or less
52 or less
47 or less
52 or less
47 or less
52 or less
57 or less
64 or less
230
260
280
500
4 position dual 3 port valve (A)
4 position dual 3 port valve (B)
4 position dual 3 port valve (C)
N.C. N.C.
N.O. N.O.
N.C. N.O.
3 position exhaust center with pressure release valves
(A)4
(B)2
(A)4
(B)2
(A)4
(B)2
(A)4
(B)2
3(R2)
1(P)
1(P)
5(R1)
3(R2)
5(R1)
1(P)
3(R2)
5(R1)
1(P)
3(R2)
5(R1)
ABC
Dual3 port valve Rubber seal VQC2 01 34 or less 44 or less
ABC
Note 1) Values represented in this column are in the following conditions:VQC1000: Cylinder port size C6 without a back pressure check valveVQC2000: Cylinder port size C8 without a back pressure check valveVQC4000: Cylinder port size Rc 3/8
Note 2) Values represented in this column are based on JIS B 8375-1981 (operating with clean air and a supply pressure of 0.5 MPa. Equipped with light/surge voltage suppressor. Values vary depending on the pressure as well as the air quality.) Values for double types are when the switch is ON.
JIS Symbol2 position single
2 position double (metal)
2 position double (rubber)
3 position closed center
3 position exhaust center
3 position pressure center
(A)( 4
B)2
1(P)(R2)
5(R1)
3
(A) 4
(B)2
1(P)
5(R1)
3 (R2)
(A) 4
(B)2
1(P)
5(R1)
3 (R2)
(A) 4
(B)2
1(P)
5(R1)
3(R2)
(A) 4
(B)2
1 (P)
5(R1)
3 (R2)
(A) 4
(B)2
1(P)
5(R1)
3 (R2)
Model
4, 2 → 5, 3 (A, B → R1, R2)1 → 4, 2 (P → A, B)
2 po
sitio
n3
posi
tion
4 po
sition
4 po
sition
Flow characteristics
0.15
0.20
0.15
0.20
0.15
0.20
0.15
0.20
0.15
0.20
0.20
0.15
0.28
0.15
0.28
0.15
0.28
0.15
0.28
0.17
0.28
0.28
0.19
0.43
0.19
0.43
0.23
0.34
0.18
0.38
0.18
0.38
––
––
0.16
0.21
0.16
0.21
0.16
0.16
0.16
0.16
0.16
0.21
0.16
0.46
0.55
0.46
0.55
0.46
0.49
0.46
0.49
0.57
0.80
0.46
1.5
2.1
1.5
2.1
1.5
1.9
1.5
1.9
1.9
1.9
––
––
0.25
0.30
0.25
0.30
0.25
0.42
0.25
0.30
0.25
0.42
0.20
0.15
0.30
0.15
0.30
0.18
0.31
0.15
0.30
0.18
0.31
0.28
0.17
0.38
0.17
0.38
0.18
0.42
0.17
0.38
0.18
0.38
––
––
0.18
0.25
0.18
0.25
0.18
0.18
0.18
0.25
0.18
0.18
0.16
0.60
0.80
0.60
0.80
0.46
0.60
0.60
0.80
0.46
0.60
0.46
1.7
2.0
1.7
2.0
1.6
1.9
1.7
2.0
1.6
2.0
––
––
C[dm3/(s•bar)] b Cv C[dm3/(s•bar)] b Cv
Plug-in Unit
Series VQCBase Mounted
2-2-22
S kit1 to 8 stations:
EX5001 to 12 stations:
EX2501 to 8 stations:
EX126
T kit1 to 10 stations
F, L, M and P kits1 to 12 stations
S kit1 to 12 stations:EX240, EX2501 to 8 stations:
EX5001 to 8 stations:
EX126
T kit1 to 10 stations
F, L, M and P kits1 to 12 stations
Standard Specifications
Manifold Specifications
Val
ve s
peci
ficat
ions
Ele
ctric
al
spec
ifica
tions
VQ
C10
00/2
000
VQ
C40
00
Single
Double
3 position
4 position
Single
Double
3 position
Valve Configuration
Fluid
Max. operating pressure
Max. operating pressure Note 3)
Min. operating pressure
Proof pressure
Ambient and fluid temperature
Lubrication
Manual override
Impact resistance/Vibration resistance
Enclosure
Rated coil voltage
Allowable voltage fluctuation
Coil insulation type
Metal seal
0.1 MPa
0.1 MPa
—
0.15 MPa
0.15 MPa
Air/Inert gas
0.7 MPa (High pressure type: 1.0 MPa) Note 4)
0.1 MPa
1.0 MPa (0.7 MPa)
0.15 MPa
1.5 MPa
–10 to 50°C Note 1)
Not required
Push type/Locking type (tool required)/Locking type (Manual override) Note 5)/Slide locking type Note 5)
150/30 m/s2 Note 2)
Dust proof (IP67 compliant)
24 VDC
±10% of rated voltage
Equivalent to B type
1 W DC (42 mA), 0.5 W DC (21 mA)
1 W DC (83 mA), 0.5 W DC (42 mA)
Rubber seal
0.15 MPa
0.2 MPa
0.15 MPa
0.2 MPa
0.2 MPa
Note 1) Use dry air to prevent condensation at low temperatures.Note 2) Impact resistance: No malfunction resulted from the impact test using a drop impact tester. The test was performed one time
each in the axial and right angle directions of the main valve and armature, for both energized and de-energized states.Vibration resistance: No malfunction occurred in a one-sweep test between 45 and 2000Hz. Test was performed in the axial and right angle directions of the main valve and armature for both energized and de-energized states.
Note 3) Values in ( ) are for the low wattage (0.5 W) specification.Note 4) Metal seal type only.Note 5) Only for VQC1000/2000.
Series
F Kit: D-sub connector
P Kit: Flat cable
T Kit: Terminal block box
S Kit: Serial transmission
L Kit: Lead wire
M Kit: Multiple connector
Base model
VQC1000 VV5QC11-
VQC2000 VV5QC21-
VQC4000 VV5QC41-
Connection type
Piping specificationsApplicable
stations
Applicablesolenoidvalves
5 stationweight
(g)Port
direction
Side
Port size Note 1)
1, 3 (P, R)
C8 (For ø8)
OptionsDirect outletwith built-in
silencer
2, 4 (A, B)
C3 (For ø3.2)
C4 (For ø4)
C6 (For ø6)
M5 (M5 threads)
C8 (For ø8)
C10 (For ø10)
C12 (For ø12)
Rc 1/4
Rc 3/8
P: Rc 1/2
R: Rc 3/4
Rc 1/4
628(Single)
759(Double, 3P)
VQC100-5
VQC101-5
Note 2)
Side
Side
Bottom
C10 (For ø10)Options
Direct outletwith built-in
silencerBranch type
C12 (for ø12)
C4 (For ø4)
C6 (For ø6)
C8 (For ø8)
1051(Single)
1144(Double, 3P)
4150• S kit (without unit)
• Solenoidweight is not included.
VQC200-5
VQC201-5
VQC400-5
VQC401-5
Note 1) One-touch fittings in inch sizes are also available.Note 2) An optional specification for special wiring is available to increase the maximum number of stations.
Min. operating pressure
24 VDC
12 VDC
Power consumption(Current)
2-2-23
Series VQCPlug-in Unit
Base Mounted
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
S VQC1000/2000/4000Kit (Serial transmission kit) Decentralized Serial Wiring
Gateway (GW) Unit IP65 compliant
Input Block IP67 compliant
Gateway type serial transmission system• Since wiring is "prepackaged" into one multi-connector type cable, wiring work is not only made
easier, but much more accurate.S kit can be used by connecting to gateway unit.
Specifications
How to Order
How to Order Input Block
EX500 IE
Nil
-X1
Applicable GW unitDeviceNet
PROFIBUS-DPRemote I/O (RIO)
1
123456
Block typeM8 connector, PNP specificationsM8 connector, NPN specificationsM12 connector, PNP specificationsM12 connector, NPN specifications
8-point integrated type, M8 connector, PNP specifications8-point integrated type, M8 connector, NPN specifications
How to Order Input Manifold
EEX500 IB1
1
8
Stations1 station
8 stations
Nil
-X1
Applicable GW unitDeviceNet
PROFIBUS-DPRemote I/O (RIO)
E 8
⋅⋅⋅⋅⋅⋅
ETM
Connector typeM8 connectorM12 connector
M8 and M12 mixed
Input unit specifications
∗ With waterproof cap
Note) When ordering an input block manifold, enter theInput manifold part no. + Input block part no.together. The input block, end block and DIN railare included in the input manifold.
Input Unit Specifications
Connection block
Short circuit protection
Communication connector
Number of connection blocks
Block supply voltage
Block supply current
Current consumption
Enclosure
Weight (g)
Current source type input block (PNP input block)or
Current sink type input block (NPN input block)
Operates at 1A Typ. (power supply cut)GW unit reset by turning power OFF and back ON.
M12 connector (8 pins, plug)
Maximum 8 blocks
24 VDC
0.65 A maximum
100 mA or less (at rated voltage)
IP65
100 (Input unit + end block)
Input Block Specifications
Applicable sensor
Sensor connector
Number of inputs
Rated voltage
Indication
Insulation
Sensor supply current
Enclosure
Weight (g)
Current source type (PNP output)or
Current sink type (NPN output)
M8 connector (3 pins) or, M12 connector (4 pins)
2 inputs/8 inputs (M8 only)
24 VDC
Green LED
None
Maximum 30 mA/Sensor
IP65
[For M8: 20] [For M12: 40] [8 point integrated type, for M8: 55]Note)
Note) Not including the DIN rail weight.
Model EX500-GAB1-X1
RockwellAutomation
PLC
57.6/115.2/230.4 kbit/sec
DeviceNet Release 2.0
125/250/500kbit/sec
PROFIBUS-DP (EN50170)
9.6/19.2/45.45/93.75/187.5/500 kbit/sec1.5/3/6/12 Mbit/sec
CC-LINKVer. 1.10
156/625 kbit/sec2.5/5/10 Mbit/sec
EX500-GDN1
Communication powersupply for DeviceNet
11 to 25 VDC
Communication powersupply for DeviceNet
50 mA or less
Input and control unit power supply: 24 VDC ± 10%Solenoid valve power supply: 24 VDC + 10%/–5% (with power drop warning at approx. 20 V)
24 VDC
200 mA or less (Single GW unit)
Maximum 64 inputs/64 outputs
8 core heavy duty cable
5 m or less (total extension 10 m or less)
M12 connector (8 pins, socket)
M12 connector (5 pins, plug)
IP65
UL, CSA, CE
470
EX500-GPR1A EX500-GMJ1
Rated voltage
Power supply voltage range
Number of input/output branches
Ambient operating temperature/humidity
Current consumption
Number of inputs/outputs
Branch cable
Branch cable length
Communication connector
Power connector
Enclosure
Applicable standard
Weight (g)
Communication speed
Applicable PLC/Communication protocol
+5 to +45°C at 35% to 85% RH (No condensation)
4 branches (16 inputs/16 outputs per branch)
Communication protocolDN1PR1A
AB1-X1MJ1
DeviceNetPROFIBUS-DP
Remote I/O (RIO)CC-LINK
EX500 G DN1—
—
—
—
—
—
2-2-24
Series VQCBase Mounted
SI Unit
How to Order
EX500 Q001
Nil
-X1
Applicable GW unitDeviceNet
PROFIBUS-DPRemote I/O (RIO)
Specifications
Connection block
Communication connector
Block supply voltage
Block supply current
Current consumption
Weight (g)
Solenoid valve (single, double)Relay output module (1 output, 2 outputs)
M12 connector (8 pins, plug, socket)
Double solenoid valveRelay output module (2 points): Maximum 8 stations
Single solenoid valveRelay output module (1 point): Maximum 16 stations
Number of connectionblock stations
24 VDC
0.65 A maximum
100 mA or less (at rated voltage)
115
Cable
How to Order Power Cable with Connector
EX500 AP S050
010050
Cable length1 m5 m
SA
Connector specificationsStraightAngle
How to Order Cable with M12 Connector
EX500 AC SSPS030
003005010030050
Cable length0.3 m0.5 m1 m3 m5 m
Connector specifications
SSPS
SAPA
Socket side: StraightPlug side: Straight
Socket side: AnglePlug side: Angle
2
3
45
6
7
18 1
7
65
4
3
28
Socket connectorpin arrangement
Plug connectorpin arrangement
Terminal no.Cable
core wire colours1 White
2 Brown3 Green
4 Yellow5 Gray
6 Pink7 Blue
1
357
8 Shield
2
46
8
Connections
2
4 3
5
Socket connectorpin arrangement
1 12
34
5
White: 24 VDC +10%/–5% (Solenoid valve power supply)
Black: 24 VDC ±10% (Input and control power supply)
Brown: 0 V (Solenoid valve power supply)
Blue: 0 V (Input and control power supply)
Grey: PE
Terminal no.
Cable core wire colors
Connections
2-2-25
Series VQCPlug-in Unit
Base Mounted
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
nLL1L2
1131177
2156202
3181227
4206252
5231277
6256302
7281327
8306352
9331377
10356402
11381427
12406452
13431477
14456502
15481527
16506552
Communication connector C2 (M12 male thread)
Pilot exhaust part2-Rc 1/8
External pilot port
VV5QC41SA1 Kit (Serial transmission kit: EX500)
2n-Rc 1/4, 3/8, C8, C10, C12 <4(A), 2(B) port>
Rc 3/8: 3/8" Female threadC8 : ø8 One-touch fitting C10 : ø10 One-touch fitting C12 : ø12 One-touch fitting
Rc 1/4:1/4" Female thread
FormulasL1 = 25n + 106 (Maximum 16 single wiring stations) n: Stations
10
6042
.715
.7
L239.5
101
P=25 65.5
L19
163
914
3
6.565.5P=25
95.5
77.5
7243
.520
.512
11.5
38.7312721.5 (6.5)
seriesEX500
COM
PWR
1
0
A A AB AB
B
A
AB AB
B
A
B
A
B
A
B
A
AB
AA
SMC SMC SMC SMC SMC SMCSMC
1 2 3 4 5 6 7 8 n
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
Communication connector C1 (M12 female thread)
2-Rc 1/8
StationsD-side U-side
3(R) port2-Rc 3/4
1(P) port2-Rc 1/2
SI unit
Manualoverride
Indicator light
2-2-28
Series VQCBase Mounted
Compatible network DeviceNet/PROFIBUS-DP/CC-Link
SI unit for DeviceNet/PROFIBUS-DP/CC-LINKAs a DeviceNet/PROFIBUS-DP/CC-LINK slave unit, this kit is capable of up to 32 points of solenoid valve ON and OFF control. Furthermore, by connecting an input block, a maximum 32 sensor signal inputs are possible.
Input blockThis expansion block connects to the SI unit and allows for sensor input to the auto switches. Each input block can receive input from up to two or four sensors, and the common can be matched to the sensor by an NPN/PNP selector switch.Input connectors are available in both M8 and M12 types.
VQC1000/2000/4000Kit (Serial Transmission Kit) for I/OS IP67 compliant
• The serial transmission system greatly reduces connection work, minimizes wiring, and saves space.
Connector Details
Communication connector: M12, 5 pinsVaries with the communication protocol. Refer to SMC's technical information.
Input connectorEX250-IE1: M12, 5 pins, 2 inputsEX250-IE2: M12, 5 pins, 4 inputsEX250-IE3: M8, 3 pins, 4 inputs
•
•
•FG terminal
•Power connector: M12, 5 pins
•Switch cover and display
SI unit for AS-iAs a AS-i slave unit, this kit is capable of up to 4 or 8 points of solenoid valve ON and OFF control.Furthermore, by connecting an inmput block, a maximun 4 or 8 sensor signal inputs are possible.
BUS
PWR
0
1
R
P
12
X
3
1
0
1
0
1
2
3
0
1
2
3
2
1
3
4
5
Circuit diagram Input module (EX250-IE∗)
4
1
1
4
2
3
5
3
4
2
1
5
3
35
4
2
1
Pos.
1
2
3
4
5
Description Function
SW+
N.C (SIGNAL)
SW–
SIGNAL
E
Sensor power supply +
Open∗
Sensor power supply –
Sensor input signal
Sensor ground connection
Pos.
1
2
3
4
5
Description Function
Drain
V+
V–
CAN_H
CAN_L
Drain / shield
Circuit power supply +
Circuit power supply –
Signal H
Signal L
∗ In the 4 input type unit (EX250-IE2), this is the input signal from the second sensor connected.
Input connection: M12 ... 5 pins (Socket)Example for the cable side connection: OMRON Corporation XS2G; Karl Lumberg GmbH: Series RST5; Franz Binder GmbH: Series 713,763
Pos.
1
3
4
Description Function
SW+
SW-
SIGNAL
Sensor power supply +
Sensor power supply –
Sensor input signal
Input connection: M8 ... 3 pins (Socket)Example for cable side connection: Franz Binder GmbH Series 718, 768 Karl Lumberg GmbH: Series RSMV3
DeviceNet: M12...5 pins (Plug) Example for a cable set with plug / socket: OMRON Corporation DCA1-5CN05F1. Karl Lumberg GmbH: 0935 253 103/...M, RSC RKC 57∗ ... M.Accessories, bus branch Y: Karl Lumberg GmbH: 0906 UTP 101, Hans Turck GmbH: VB2-FKM-FSM57.Accessories terminating socket with resistor: Hans Turck GmbH: RSE57-TR2, Karl Lumberg GmbH: 0939 CXT 101.
Pos.
1
2
3
4
5
Description Function
SV24V
SV0V
SW24V
SW0V
E
+24 V solenoid valve
0V solenoid valve
+24 V SI and input blocks
0 V SI and input blocks
Ground connection
Power supply DeviceNet:: M12 ... 5 pins reserve-keyed (Plug)(The configuration of the connection surface area differs from that of the transmission plug)Example of the cable set with socket: Hans Turck GmbH: WAKW4.5T-2, Franz Binder GmbH: 79-4449-..-05.
Pos.
1
2
3
4
5
Description Function
VP
A-N
DGND
B-P
SHIELD
Power supply for terminating resistor
Negative for data transfer/reception
Ground for terminating resistor
Positive for data transfer/reception
Shield
PROFIBUS-DP: M12... 5 pins reserve-keyed (Socket).Example for the corresponding cable sets with plug / socket:Hans Turck GmbH: RSSW-RKSW456-...M; Karl Lumberg GmbH: 0975 254 101/...M Accessories Bus branch Y: Hans Turck GmbH: VB2/FSW/FKW/FSW45Accessories terminating resistor: Hans Turck GmbH: RSS4.5-PDP-TR; Karl Lumberg GmbH: 0979PTX101
Pos.
1
2
3
4
5
Description Function
SV24V
SV0V
SW24V
SW0V
E
+24 V solenoid valve
0 V solenoid valve
+24 V SI and input blocks
0 V SI and input blocks
Ground connection
3
4
2
1
5
PROFIBUS-DP: M12...5 pins (Plug)Example of the cable set with socket: SMC: EX500-AP...S (See page 2-2-25.)
CANopen: Female connector cable: M12 female 5 pins cable with shield (according to ISO11898).Communication connector
3
4
2
1
5
Pos.
1
2
3
4
5
Description Function
CAN_SHLD
CAN_V+
CAN_GND
CAN_H
CAN_L
Shield
Power supply +
Power supply –
Bus line (dominant High)
Bus line (dominant Low)
2-2-30
Series VQCBase Mounted
Communication connectorAS-i EX250-SAS7 / EX250-SAS9Communication connector: M12 male 4 pins
Connection example
2
1
4
3
EX250-SAS7
AS-i Standard cable(YELLOW CABLE)
Communication connector
Ground terminal
Output equipmentpower connector
EX250-SAS3
AS-i Standard cable(YELLOW CABLE)
AS-i Standard cable(BLACK CABLE)
Pos.
1
2
3
4
Description Function
AS-i +
RESERVE
AS-i –
RESERVE
Positive AS-Interface line
RESERVE
Negative AS-Interface line
RESERVE
M12 Cable Recommendation Conductor cross-section 1.5 mm2
Connector for T-branchASI FK M12Hirschmann etc.(IEC 603526)
AS-i EX250-SAS3 / EX250-SAS5Communication connector: M12 male 4 pins
2
1
4
3
2
1
4
3
Output equipment power connector: M12 male 4 pins
Pos.
1
2
3
4
Description Function
AS-i +
0V
AS-i –
24V
Positive AS-Interface line
Negative output equipment power line
Negative AS-Interface line
Positive output equipment power line
Pos.
1
2
3
4
Description Function
24V
NC
0V
NC
Positive output equipment power line
Not connected
Negative output equipment power line
Not connected∗ Connected inside the SI unit.
Connection example M12 CableRecommendation Conductor cross-section 1.5 mm2
Connector for T-branchASI FK M12Hirschmann etc.(IEC 603526)
∗
2-2-31
Series VQCPlug-in Unit
Base Mounted
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
VQC1000/2000/4000Kit (Serial transmission kit) for I/OS
Name
PWR(V)
PWR
MOD/NET
ON when solenoid valve power supply is turned ON.
ON when DeviceNet circuit power supply input is turned ON.
OFF: Power supply off, off line, or when checking duplication of MAC_ID.
GREEN BLINKING: Waiting for connection (on line).
GREEN ON: Connection established (on line).
RED BLINKING: Connection time out (minor communication abnormality).
RED ON: MAC_ID duplication error, or BUSOFF error(major communication abnormality).
Description Function
ON when sensor power is turned ON.
ON when each sensor input goes ON.
SI unit DeviceNet (EX250-SDN1)
PROFIBUS-DP (EX250-SPR1)
CC-Link (EX250-SMJ2)
Input block (EX250-IE1/2/3)
Indicator Unit (LED) Description and Its Function
∗ Please contact your SMC representative for specifications and handling precautions.
PWR
0
1
2
3
EX250
2-input type(EX250-IE1)
1
0
PWR
EX250
4-input type(EX250-IE2/3)
PWR
0 to 1(3)
Function
Name Function
PWR(V)
RUN
DIA
BF
GREEN ON when solenoid valve power supply is turned ON.
GREEN OFF when the power supply voltage is less than 19 V.
GREEN ON when operating (SI unit power supply is ON).
RED ON when self diagnosis device detects abnormality.
RED ON for BUS abnormality.
Name Function
PW
PW(V)
L RUN
L ERR
ON: Input and control unit power supply ON.OFF: Input and control unit power supply OFF.
ON: Solenoid valve power supply ON.OFF: Solenoid valve power supply voltage is less than 19 V.
ON: Normal trafficOFF: Traffic disconnected (Timeover error)
ON: Traffic errorBLINKING: Station or baud rate switch is set while the power supply is ON.OFF: Normal traffic
When the data link is normal, PW, PW (V) and L RUN are ON.
SETTINGS
1
PWR(V) PWR MOD/NET
0
EX250
ADDRESS SETTING
SW
EX250
ADDR2ADDR1
HOLD
CLEAR
COM-ERR
INAUX -ERRPWR
SI
AS-i (EX250-SAS)
ContentsNameLED
Condition
PWR
AUX
IN-ERR
COM-ERR
GreenLight
GreenLight
Red Light
Red Light
Red Blink
In time of power supply for AS-Interface line is turned on.
In time of auxiliary power supply for outputequipment is turned on.
In time of input power is detected over current.(Lights off at normal condition)
In time of communication error.(Lights off at normal condition)
In time of peripheral equipment error.(Over current of input power, blowing the fuse etc.)
SI unit CANopen (EX250-SCA1)
ADDRESS
1
PWR(V) PWR CAN
0
EX250
ContentsNameLED
Condition
PWR(V)
PWR
CAN
Green LightGreen LightGreen LightGreen Light (Blinking)Green Light (Single flash)Red Light (Single flash)Red Light (Double flash)Green/Red Light(flickering)Red Light
Illuminates when power for solenoid valves is suppliedIlluminates when power for CANopen line is suppliedIlluminates when SI unit is in the Operational stateSI unit is in the Pre-operational stateSingle flash when SI unit is in Stopped stateSingle flash when CAN controller error occursDouble flash when Error Control Event occursFlickering when SI unit is in Configuration mode(LSS services)Red Light SI unit is in “Bus OFF” state
IP67 compliant
2-2-32
Series VQCBase Mounted
nLL1L2
1131230
2156255
3181280
4206305
5231330
6256355
7281380
8306405
9331430
10356455
11381480
12406505
13431530
14456555
15481580
16506605
10
6042
.7
6641
.5
L2
5.5 108
21 21 63
101
P=25 65.5
L1
9
163
914
3
6.5
65.5P=25
95.5
77.5
72
43.5
12
11.5
38.7
31
27
21.5 (6.5)
32
10
1
0
PWR
BUS
M8 female threadInput connector
M12 female threadInput connector
M12 male threadCommunication connector
M3 female threadEarth terminalM12 male thread
Power connector
SI unitInput block
3(R) port2-Rc 3/4
1(P) port2-Rc 1/2
Pilot exhaust port2-Rc 1/8
External pilot port2-Rc 1/8
Manual overrideIndicator light
A A AB AB
B
A
AB AB
B
A
B
A
B
A
B
A
AB
AA
SMC SMC SMC SMC SMC SMCSMC
20.5
15.7
n1 2 3 4 5 6 7StationsD-side 8 U-side
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2n-Rc 1/4, 3/8, C8, C10, C12 <4(A), 2(B) port>
Rc 3/8: 3/8" Female threadC8 : ø8 One-touch fitting C10 : ø10 One-touch fitting C12 : ø12 One-touch fitting
Rc 1/4: 1/4" Female thread
FormulasL1 = 25n + 106 (Maximum 16 single wiring stations)∗ L2: For one input block. Add 21 mm for each additional input block. n: Stations
VV5QC41S Kit(Serial transmission kit: EX250)
VQC1000/2000/4000Kit (Serial transmission kit) for I/OS IP67 compliant
2-2-34
Series VQCBase Mounted
PWR(V) MOD/NETPWR
1
0
TMTM
FB
PS
SETTINGS
Compatible network DeviceNet/PROFIBUS-DP
DeviceNet/PROFIBUS-DP compatible SI unitAs a DeviceNet/PROFIBUS-DP slave unit, this kit is capable of solenoid valve ON and OFF control up to 32 points. Furthermore, by connecting an input block, up to 32 sensor signal inputs are possible.
Input blockThis expansion block connects to the SI unit and allows for sensor input to the auto switches. Each input block can receive input from up to 8 sensors, and the common can be matched to the sensor by an NPN/PNP selector switch.
SI unit (DeviceNet) SI unit (PROFIBUS-DP) Input block
Indicator Unit (LED) Description and Its Function
Connector Details
VQC4000Kit (Serial transmission kit) for I/O S
1
2
4
3
5
5
4
3
1
2
1
2
34
5
• Input connector: M12, 5 pins (OMRON Corporation XS2F compatible) x 8 pcs. Cable side connector example: OMRON Corporation XS2G
SW + SIGNAL -n + 1
SW–SIGNAL -n
PE
No.
1
2
3
4
5
Description
SW +
N.C.
SW –
SIGNAL
PE
Function(+) Sensor power supply
Open∗
(–) Sensor power supply
Sensor input signal
Protective sensor ground
∗ The second pin of the connector with input no. 0, 2, 4, 6 (the connector at the right side of the input block) is connected internally to the fourth pin (sensor input no.) of the connector with input no. 1, 3, 5, 7. This makes it possible to directly input two inputs that are combined together by the common connector.
• Power connector: Franz Binder GmbH Series 723, 5 pins (72309-0115-80-05)Cable side connector example: Franz Binder GmbH 72309-0114-70-15, etc.∗ DIN type 5 pins
• Communication connector (DeviceNet): M12, 5 pins (for DeviceNet only)Example of corresponding cable assemblies with connector:OMRON Corporation DCA1-5CN05F1, Karl Lumberg GmbH & Co. KG RKT5-56.
No.
1
2
3
4
5
Description
SV24V
SV0V
PE
SW24V
SW0V
Function
For solenoid valve +24V
For solenoid valve +0V
Protective ground
For solenoid valve +24V
For solenoid valve +0V
No.
1
2
3
4
5
Description
Drain
V +
V –
CAN_H
CAN_L
Function
Drain/Shield
(+) Circuit power supply
(–) Circuit power supply
Signal H
Signal L
Compatible with DeviceNet specification Micro Style connector.
• Communication connector (PROFIBUS-DP):CONINVERS GmbH RC-2RS1N12, 12 pinsCable side connector example: Siemens AG 6ES5 760-2CB11
No.
1
2
4
6
9
12
Description
M5V
A
B
+5V
SHIELD
RTS
Function
GND Terminal
Signal –N
Signal –P
Terminal +5V
Shield ground
Optical fiber (reserve)
Input block SI unit (DeviceNet) SI unit (PROFIBUS-DP)
Input connector
Communicationconnector
Power connector
12345
12345
Connector: Input no. 0, 2, 4, 6 Input no. 1, 3, 5, 7
When IP65 or equivalent enclosures are required, install a waterproof cover on the input connector that is not being used. Order waterproof covers separately.Example: OMRON Corporation XS2Z-12
Caution
Description
PWR(V)
PWR
MOD/NET
Function
ON when solenoid valve power supply is turned ON.
ON when DeviceNet circuit power supply input is turned ON.
OFF: Power supply off, off line, or when checking duplication of MAC_ID.
GREEN BLINKING: Waiting for connection (on line).
GREEN ON: Connection established (on line).
RED BLINKING: Connection time out (minor communication abnormality).
RED ON: MAC_ID duplication error, or BUSOFF error(major communication abnormality).
Description Function
PWR(V)
RUN
DIA
BF
ON when solenoid valve power supply is turned ON.
OFF when the power supply voltage is less than 19V.
ON when operating (SI unit power supply is ON).
ON when self diagnosis device detects abnormality.
ON for BUS abnormality.
Description
PWR
0 to 7
Function
ON when sensor power is turned ON.
OFF when short circuit protection is working.
ON when each sensor input goes ON.
129
1
2
4
6
PWR(V) MOD/NETPWR
1
0
TMTM
FB
PS
SETTINGS
ADDRESS
H
DIA BF
L
PWR(V) RUN
FB
PS
0246
1357
PWR
• The serial transmission system greatly reduces connection work, minimizes wiring, and saves space.
• Pin no. 3, 5, 7, 8, 10 and 11 marked with "" are open.
∗ The connector configuration and the pin arrangement are compatible with Siemens AG ET200C.
IP65 compliant
2-2-36
Series VQCBase Mounted
VV5QC41S Kit (Serial transmission kit: EX240)
nLL1L2
1131266
2156291
3181316
4206341
5231366
6256391
7281416
8306441
9331466
10356491
11381516
12406541
13431566
14456591
15481616
16506641
Formulas: L1 = 25n + 106, L2 = 25n + 241 (For 1 input block. For each additional input block, add 54 mm.) n: Stations (Maximum 16 stations)
101
1014
3
(32)
(98.
8)
143
99
1016
3
(14.5)
128.5
54 P = 25
ABABABABAAA B
65.5
L1(8) 6.5
L2 (1 input block: 8 inputs)
Min.0 to Max. 4unit
(0 to 216mm)
Indicator light
Manual override
Mounting hole for 2-M5, with input block onlyInput block
SI unit
75.5
61.5
42.7
15.7
(1.5
)
1220
.5
43.5
11.5 21.5 (6.5)
2731
38.5
77.5
72
95.5
8
23
2-Rc 1/8(External pilot port)
2-Rc 1/8(Pilot EXH port)
2-Rc 3/43(R) port
2-Rc 1/21(P) port
n1 2 3 4 5 6 7StationsD-side 8 U-side
SMC
2 B
4 A
SMC
2 B
4 A
SMC
2 B
4 A
SMC
2 B
4 A
SMC
2 B
4 A
SMC
2 B
4 A
SMC
2 B
4 A
2 B
4 A
2n-Rc 1/4, 3/8, C8, C10, C12 <4(A), 2(B) port>Rc 1/4:1/4" Female threadRc 3/8: 3/8" Female threadC8 : ø8 One-touch fitting C10 : ø10 One-touch fitting C12 : ø12 One-touch fitting
2-2-37
Series VQCPlug-in Unit
Base Mounted
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
TM
TM
Terminal Block Connection
Terminal Block Details
• Terminal block LED descriptions
• Cable wiring
• Note
0
54
32
19
8
6
7
0
54
32
19
8
6
7
0
54
32
19
8
6
7
24V 0V +24V 24G DA DB FG
SD RDLERR.
STATION NO.
x10 x1
B RATE
PW LRUN
DG
SLDFG
DGDBDA
FGDGDBDA
FGDGDBDA
Master unit SI unit SI unit
Type 3 grounding Type 3 grounding Type 3 grounding
Shielded twisted pair cable
Terminatingresistance
Terminatingresistance
• CC-LINK System Master unit: AJ61BT11 Master unit: A1SJ61BT11 Master unit: AJ61QBT11 Master unit: A1SJ61QBT11
• 16 outputs
Terminal block cover
Mounting screw (M4)
Gasket
6mm
VQC1000/2000/4000Kit (Serial transmission kit) for I/OS
Compatible network CC-Link
• The serial transmission system greatly reduces connection work, minimizes wiring, and saves space.
Step 1. How to remove terminal block coverLoosen the 4 mounting screws (M4) and remove the terminal block cover.
Step 2. Wire the cables according to the terminal block specifications below. Pay attention to the wire bound positions.
Electrical entry4-G1/2
M3 screw
Proper tightening torque (N⋅m)
0.7 to 1.2
Step 3. How to replace the terminal block coverSecurely tighten the screws to the torque shown in the table below, after confirming that the gasket is installed correctly.
• Applicable crimp terminal (fork tongue type): 1.25-3S, 1.25Y-31.25Y-3N, 1.25Y-3.5
∗ For detailed specifications and handling, refer to the operation manual provided by SMC.
Description
PW
L RUNSDRD
L ERR.
FunctionON when transmission power supply is ON.
OFF when transmission power supply is OFF.ON when normal data is received.
ON when data is sent.ON when data is received.
ON for transmission error and incorrect settings. BLINKING for change in station or transmission speed settings.
IP67 compliant
2-2-38
Series VQCBase Mounted
VV5QC41S Kit (Serial transmission kit: EX126)
nLL1L2
1131217
2156242
3181267
4206292
5231317
6256342
7281367
8306392
9331417
10356442
11381467
12406492
13431517
14456542
15481567
16506592
SMC SMCSMCSMCSMCSMCSMC
1 2 3 4 5 6 7 8 n
A A
B A
A
B
A
B
A
B
A
B
B AB A
A
B
B AB AAA
2-Rc 1/8(External pilot port)
2-Rc 3/43(R) port
2-Rc 1/21(P) port
2-Rc 1/8(Pilot exhaust port)
4-G 1/2Conduit port
(6.5)21.52731
38.7
11.5 12
20.5 43.5 77
.5 95.5
P=25 65.56.5
143
9
163
9
101
L179.5L2
8034
.5
4672
55.5
13
42
R4.
5
R4.5
72
10
15.7
42.7
55.5
90
33.5
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2n-Rc 1/4, 3/8, C8, C10, C12 <4(A), 2(B) port>Rc 1/4: 1/4" Female threadRc 3/8: 3/8" Female threadC8 : ø8 One-touch fittingC10 : ø10 One-touch fittingC12 : ø12 One-touch fitting
FormulasL1 = 25n + 106 (Maximum 16 single wiring stations)L2 = 25n + 192 n: Stations
Manual overrideIndicator light
SI unit
Mounting hole for 2-M5
StationsD-side U-side
2-2-41
Series VQCPlug-in Unit
Base Mounted
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
Mani
Flat
Con· Hir· Su· Fu· Ja· J.S
Cable
Connecto
AX
L dimensio
Weight (g
No.
L dimensio
Weight (g
No.
L dimensio
Weight (g
No.
L dimensio
Weight (g
No.
262
W
Term
∗ For othto MIL-
1.
3
5
Manifold Option
Circular connector/Cable assembly (26 pins) D-sub connector/Cable assembly (25 pins)
When a commercially available connector is required, use a 25 pinfemale connector conforming to MIL-C24308.
Note) The minimum inside bending radius for each cable is 20 mm.
Part no.
AXT100-MC26-015
AXT100-MC26-030
AXT100-MC26-050
Lead Wire Length
1.5 m
3 m
5 m
Terminal no.
q
w
e
r
t
y
u
i
o
!0
!1
!2
!3
!4
!5
!6
!7
!8
!9
@0
@1
@2
@3
@4
@5
Lead wire color
Black
Brown
Red
Orange
Yellow
Pink
Blue
Purple
Gray
White
White
Yellow
Orange
Yellow
Pink
Blue
Purple
Gray
Orange
Red
Brown
Pink
Gray
Black
White
Dot marking
None
None
None
None
None
None
None
White
Black
Black
Red
Red
Red
Black
Black
White
None
None
Black
White
White
Red
Red
White
None
AXT100 MC26– –
Part no.
AXT100-DS25-015
AXT100-DS25-030
AXT100-DS25-050
Lead Wire Length
AXT100 DS25– –
Circular Connector Cable Assembly Terminal No.
Terminal no.
q
w
e
r
t
y
u
i
o
!0
!1
!2
!3
!4
!5
!6
!7
!8
!9
@0
@1
@2
@3
@4
@5
Lead wire color
Black
Brown
Red
Orange
Yellow
Pink
Blue
Purple
Gray
White
White
Yellow
Orange
Yellow
Pink
Blue
Purple
Gray
Orange
Red
Brown
Pink
Gray
Black
White
Dot marking
None
None
None
None
None
None
None
White
Black
Black
Red
Red
Red
Black
Black
White
None
None
Black
White
White
Red
Red
White
None
D-sub Connector Cable AssemblyTerminal No.
Item
Conductor resistance W/km, 20°C
Withstand voltage VAC, 1 min.
Insulation resistance, M/km, 20°C
Characteristics
65 or less
1000
5 or less
Circular Connector, D-sub Connector Cable AssemblyElectric Characteristics
Plug terminal no.(arrangement as seen from lead wire side)
q!5!4@4!3
!2 @3
@2!1
!0o i
@1
@6
@5
!6!7w
e
r!8
!9
y
t@0
u
1425
113 Multi-core vinyl cable
0.3 mm2 x 25C
2-M2.6 x 0.45
Terminalno.
Socket side
16
(60)
L
44L
8
47.0
4
50
" ø
10
Note) Terminal no.@6 is connected to @5 inside the connector.
L dimension1.5 m
3 m
5 m
L dimension
Series VQC
2-2-42
1_02_SV.qxd 04.6.16 14:30 Page 2-96
VV5QC41
nLL1L2
1131 164.5
2156 189.5
3181 214.5
4206 239.5
5231 264.5
6256 289.5
7281 314.5
8306 339.5
9331 364.5
10356 389.5
11381 414.5
12406 439.5
13431 464.5
14456 489.5
15481 514.5
16506 539.5
FormulasL1 = 25n + 106 (Maximum 16 single wiring stations)L2 = 25n + 139.5 n: Stations
(Conforms to MIL-C-24308)
Applicable connector: D-sub connector (25P)
n1 2 3 4 5 6 7StationsD-side 8 U-side
3(R) port2-Rc 3/4
1(P) port2-Rc 1/2
Pilot exhaust port
2-Rc 1/8External pilot port
2-Rc 1/8
2n-Rc 1/4, 3/8, C8, C10, C12 <4(A), 2(B) port>
Rc 3/8: 3/8" Female threadC8 : ø8 One-touch fitting C10 : ø10 One-touch fitting C12 : ø12 One-touch fitting
Rc 1/4: 1/4" Female thread
10
101
60
67
74.5
L227
42.7
15.7
P=25 65.5
L19
163
914
36.5
65.5P=25
95.5
77.5
43.5
11.5
38.7
31
27
21.5 (6.5)
Manual release for switching connector direction
D-sub connector cable assembly (25P)
Manual overrideIndicator light
A A AB AB
B
A
AB AB
B
A
B
A
B
A
B
A
AB
AA
SMC SMC SMC SMC SMC SMCSMC
20.5
12
44
72
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2-2-45
Series VQCPlug-in Unit
Base Mounted
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
Note) When using the negative COM. specification for VQC1000/2000, use valves for negative COM.
VQC1000/2000/4000Kit (Flat ribbon cable kit) P
Cable AssemblyElectrical Wiring Specifications
Mixed single and double wiring are available as options. The maximum number of manifold stations is determined by the number of solenoids. Count one point for a single solenoid type and two points for a double solenoid type. The total number of solenoids (points) must not exceed 24.
AXT100-FC -123
2026
Flat ribbon cable connector assemblies (Option)Cablelength (L)
Part no.
1.5 m3 m5 m
26PAXT100-FC26-1AXT100-FC26-2AXT100-FC26-3
20PAXT100-FC20-1AXT100-FC20-2AXT100-FC20-3
Connector Manufacturers Example:
• Hirose Electric CO., Ltd.• Sumitomo/3-M Limited• Fujitsu, Ltd.• Japan Aviation Electronics Industry, Ltd.• J.S.T. Mfg. Co., Ltd.• Oki Electric Cable Co., Ltd.
6
(15.6)
L
Terminal no.
Red
28AWG
30
(20P
)37
.5 (
26P
)
262
251
Flat ribbon cable connector
<26P> <20P>
Connector terminal number
26
24
22
20
18
16
14
12
10
8
6
4
2
25
23
21
19
17
15
13
11
9
7
5
3
1
Triangle mark indicator position
Double wiring (connected to SOL. A and SOL. B) is used for the internal wiring of each station regardless of valve and option types.Mixed single and double wiring are available as options.Refer to special wiring specifica-tions (options) below.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
COM
COM
Station 1
Station 2
Station 3
Station 4
Station 5
Station 6
Station 7
Station 8
Station 9
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
COM
COM
Station 1
Station 2
Station 3
Station 4
Station 5
Station 6
Station 7
Station 8
Station 9
Station 10
Station 11
Station 12
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(–)
(–)
Terminalno.
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(–)
(+)
(+)
Polarity
PositiveCOM.spec.
NegativeCOM.spec.
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(–)
(–)PositiveCOM.spec.
NegativeCOM.spec.
26
24
22
20
18
16
14
12
10
8
6
4
2
25
23
21
19
17
15
13
11
9
7
5
3
1
COM. COM.
(For 26P)
20
18
16
14
12
10
8
6
4
2
19
17
15
13
11
9
7
5
3
1
COM. COM.
(For 20P)
Special Wiring Specifications (Option)
• Using our flat ribbon cable for electrical connections greatly reduces labour, while it also minimizes wiring and saves space.
• We use flat ribbon cables whose connectors (26P and 20P) conform to MIL standards, and are therefore widely compatible with many standard commercial models.
• Top or side entry for the connector can be changed freely, allowing for changes even after mounting, to meet any changing needs for space.
Terminalno.
Polarity
Type 26P flat ribbon cable connector assemblies can be ordered with manifolds. Refer to manifold ordering.
∗ When using a standard commercial connector, use a type 26P connector conforming to MIL-C-83503 or a type 20P with strain relief.
∗ Cannot be used for transfer wiring.
IP40 compliant
2-2-46
Series VQCBase Mounted
VV5QC41
nLL1L2
1131 164.5
2156 189.5
3181 214.5
4206 239.5
5231 264.5
6256 289.5
7281 314.5
8306 339.5
9331 364.5
10356 389.5
11381 414.5
12406 439.5
13431 464.5
14456 489.5
15481 514.5
16506 539.5
FormulasL1 = 25n + 106 (Maximum 16 single wiring stations)L2 = 25n + 139.5 n: Stations
(Conforms to MIL-C-83503)
Applicable connector: Flat ribbon cable connector (26P)n1 2 3 4 5 6 7StationsD-side 8 U-side
External pilot port2-Rc 1/8Pilot exhaust port
2-Rc1/8
2n-Rc 1/4, 3/8, C8, C10, C12 <4(A), 2(B) port>
Rc 3/8: 3/8" Female threadC8 : ø8 One-touch fitting C10 : ø10 One-touch fitting C12 : ø12 One-touch fitting
Rc 1/4: 1/4" Female thread
Manual overrideIndicator light
10
6774
.5
L227 L1
9
163
914
36.5
65.5P=25
A A AB AB
B
A
AB AB
B
A
B
A
B
A
B
A
AB
AA
101
6042
.715
.7
P=25 65.5
95.5
77.5
7243
.512
11.5
38.7312721.5 (6.5)
AXT100-FC26-3: 5 mAXT100-FC26-2: 3 mAXT100-FC26-1: 1.5 m
3(R) port2-Rc 3/4
1(P) port2-Rc 1/2
SMC SMC SMC SMC SMC SMCSMC
20.52 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
Manual release for switching connector direction
Flat ribbon cable connector assembly (26P)
2-2-49
Series VQCPlug-in Unit
Base Mounted
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
Note) When using the negative COM. specification for VQC1000/2000, use valves for negative COM.
• This kit has a small terminal block inside a junction box. The provision of a G 3/4 electrical entry allows connection of conduit fittings.
VQC1000/2000/4000Kit (Terminal block box kit)T
SOL. A1A (–) (+)
SOL. B1B (–) (+)
Station 1
SOL. A2A (–) (+)
SOL. B2B (–) (+)
Station 2
SOL. A3A (–) (+)
SOL. B3B (–) (+)
Station 3
SOL. A4A (–) (+)
SOL. B4B (–) (+)
Station 4
SOL. A5A (–) (+)
SOL. B5B (–) (+)
Station 5
SOL. A6A (–) (+)
SOL. B6B (–) (+)
Station 6
SOL. A7A (–) (+)
SOL. B7B (–) (+)
Station 7
SOL. A8A (–) (+)
SOL. B8B (–) (+)
Station 8
SOL. A9A (–) (+)
SOL. B9B (–) (+)
Station 9
SOL. A10A (–) (+)
SOL. B10B (–) (+)
Station 10
(+) (–)
Terminalno.
Polarity
PositiveCOM.
NegativeCOM.
Electrical Wiring Specifications (Conforms to IP67)
COM.
Standard wiring
The internal wiring is double (con-nected to SOL. A and SOL. B) for all stations regardless of the type of valve or options.Mixed single and double wiring are available as options.
1ACOM
2A3A
4A5A
6A7A
8A9A
10A
1B2B
3B4B
5B6B
7B8B
9B10B
1B1A
2B2A
3B3A
4B4A
5B5A
6B6A
7B7A
8B8A
9B9A
10B10A
COM
1ACOM
2A3A
4A5A
6A7A
8A9A
10A
1B2B
3B4B
5B6B
7B8B
9B10B
1B1A
2B2A
3B3A
4B4A
5B5A
6B6A
7B7A
8B8A
9B9A
10B10A
COM
Terminal Block Connection
Proper tightening torque (N⋅m)
0.7 to 1.2
Mounting screw (M4)Terminal block cover
Gasket
Electrical entry2-G3/4
M3 screw
6mm
Step 3. How to replace the terminal block coverSecurely tighten the screws to the torque shown in the table below, after confirming that the gasket is installed correctly.
Step 1. How to remove terminal block coverLoosen the 4 mounting screws (M4) and remove the terminal block cover.
Step 2. The diagram below shows the terminal block wiring. All stations are provided with double wiring regardless of the valves which are mounted.Connect each wire to the power supply side, according to the markings provided inside the terminal block.
Special Wiring Specifications (Option)
Mixed single and double wiring are available as options. The maximum number of manifold stations is determined by the number of solenoids. Count one point for a single solenoid type and two points for a double solenoid type. The total number of solenoids (points) must not exceed 20.
1. How to orderIndicate option symbol "-K" in the manifold part number and be sure to specify station positions for single or double wiring on the manifold specification sheet.
2. Wiring specificationsConnector terminal numbers are connected from solenoid station 1 on the A side in the order indicated by the arrows without skipping any terminal numbers.
• Applicable crimp terminal (fork tongue type): 1.25-3S, 1.25Y-31.25Y-3N, 1.25Y-3.5
IP67 compliant
2-2-50
Series VQCBase Mounted
VV5QC41
nLL1L2
1131217
2156242
3181267
4206292
5231317
6256342
7281367
8306392
9331417
10356442
11381467
12406492
13431517
14456542
15481567
16506592
FormulasL1 = 25n + 106 (Maximum 16 single wiring stations)L2 = 25n + 192 n: Stations
101
80 143
163
99
10
779.5 L1
ABABABABAAA B
6.565.5P=25
L2
34.5
77.5
45.5
42.7
15.7 35 12
20.5
43.5 77
.572 95
.5
(6.5)
11.5
21.52731
38.7
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
SMC SMC SMC SMC SMC SMC SMC
Indicator lightManual override
2-Rc 1/8(External pilot port)
2-Rc 1/8(Pilot EXH port)
Mounting holefor 2-M5
2-G 3/4Conduit port
n1 2 3 4 5 6 7StationsD-side 8 U-side
2-Rc 3/43(R) port2-Rc 1/21(P) port
2n-Rc 1/4, 3/8, C8, C10, C12 <4(A), 2(B) port>Rc 1/4 : 1/4" Female threadRc 3/8 : 3/8" Female threadC8 : ø8 One-touch fitting C10 : ø10 One-touch fitting C12 : ø12 One-touch fitting
2-2-53
Series VQCPlug-in Unit
Base Mounted
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
L
As the standard electrical wiring specifica-tion used is for 12 stations or less, double wiring (connected to SOL. A and SOL. B) is used for the internal wiring of each sta-tion regardless of valve and option types.Mixed single and double wiring are avail-able as options.Refer to special wiring specifications (op-tions) below.
Mixed single and double wiring are available as options. The maximum number of manifold stations is determined by the number of solenoids. Count one point for a single solenoid type and two points for a double solenoid type. The total number of solenoids (points) must not exceed 24.
VV5QC11 08 C6 LD 0
012
Lead wire length0.6 m1.5 m3.0 m
SheathColour: Urban white
Lead wire0.3 mm2 × 25 core
Note) When using the negative COM. specification for VQC1000/2000, use valves for negative COM.
Electrical Wiring Specifications
1 (–) (+) Black NoneSOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
SOL. A
SOL. B
COM.
14 (–) (+) Yellow BlackStation 1
Station 2
Station 3
Station 4
Station 5
Station 6
Station 7
Station 8
Station 9
Station 10
Station 11
Station 12
2 (–) (+) Brown None
15 (–) (+) Pink Black
3 (–) (+) Red None
16 (–) (+) Blue White
4 (–) (+) Orange None
17 (–) (+) Purple None
5 (–) (+) Yellow None
18 (–) (+) Grey None
6 (–) (+) Pink None
19 (–) (+) Orange Black
7 (–) (+) Blue None
20 (–) (+) Red White
8 (–) (+) Purple White
21 (–) (+) Brown White
9 (–) (+) Grey Black22 (–) (+) Pink Red
10 (–) (+) White Black
23 (–) (+) Grey Red11 (–) (+) White Red
24 (–) (+) Black White
12 (–) (+) Yellow Red
25 (–) (+) White None
13 (+) (–) Orange Red
PolarityTerminalno.
Lead wirecolour
Dotmarking
PositiveCOM.spec.
NegativeCOM.spec.
Lead wire specifications Lead wire length
Special Wiring Specifications (Option)
Note)
VQC1000/2000/4000Kit (Lead wire kit)
• Direct electrical entry type. • IP67 enclosure is available with use of cables with sheath and waterproof
connectors.
Electrical characteristics
Item Characteristic
Conductor resistanceΩ/km, 20°CWithstand pressureV, 1 minute, AC
Insulation resistanceMΩ/km, 20°C
65 or less
1000
5 or more
Note) Cannot be used for transfer wiring.The minimum bending radius for cables is 20 mm.
IP67 compliant
2-2-54
Series VQCBase Mounted
VV5QC41
nLL1L2
1131 185.5
2156 210.5
3181 235.5
4206 260.5
5231 285.5
6256 310.5
7281 335.5
8306 360.5
9331 385.5
10356 410.5
11381 435.5
12406 460.5
13431 485.5
14456 510.5
15481 535.5
16506 560.5
FormulasL1 = 25n + 106 (Maximum 16 single wiring stations)L2 = 25n + 160.5 n: Stations
Manual overrideIndicator light
0.6
m, 1
.5 m
, 3 m
Lead
wire
leng
th
3(R) port2-Rc 3/4
1(P) port2-Rc 1/2
n1 2 3 4 5 6 7StationsD-side 8 U-side
Pilot exhaust port2-Rc 1/8
External pilot port2-Rc 1/8
2n-Rc 1/4, 3/8, C8, C10, C12 <4(A), 2(B) port>Rc 1/4: 1/4" Female threadRc 3/8: 3/8" Female threadC8 : ø8 One-touch fitting C10 : ø10 One-touch fitting C12 : ø12 One-touch fitting
10
42.7
18
L248
101
60
74.5
P=25 65.5
L19
163
914
3
6.565.5P=25
95.5
77.5
7243
.512
11.5
38.73127
(6.5)
A A AB AB
B
A
AB ABB
A
B
A
B
A
B
A
AB
AA
SMC SMC SMC SMC SMC SMCSMC
20.5
21.5
15.7 2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2-2-57
Series VQCPlug-in Unit
Base Mounted
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
Mani
Flat
Con· Hir· Su· Fu· Ja· J.S
Cable
Connecto
AX
L dimensio
Weight (g
No.
L dimensio
Weight (g
No.
L dimensio
Weight (g
No.
L dimensio
Weight (g
No.
262
W
Term
∗ For othto MIL-
1.
3
5
Manifold Option
Circular connector/Cable assembly (26 pins) D-sub connector/Cable assembly (25 pins)
When a commercially available connector is required, use a 25 pinfemale connector conforming to MIL-C24308.
Note) The minimum inside bending radius for each cable is 20 mm.
Part no.
AXT100-MC26-015
AXT100-MC26-030
AXT100-MC26-050
Lead Wire Length
1.5 m
3 m
5 m
Terminal no.
q
w
e
r
t
y
u
i
o
!0
!1
!2
!3
!4
!5
!6
!7
!8
!9
@0
@1
@2
@3
@4
@5
Lead wire color
Black
Brown
Red
Orange
Yellow
Pink
Blue
Purple
Gray
White
White
Yellow
Orange
Yellow
Pink
Blue
Purple
Gray
Orange
Red
Brown
Pink
Gray
Black
White
Dot marking
None
None
None
None
None
None
None
White
Black
Black
Red
Red
Red
Black
Black
White
None
None
Black
White
White
Red
Red
White
None
AXT100 MC26– –
Part no.
AXT100-DS25-015
AXT100-DS25-030
AXT100-DS25-050
Lead Wire Length
AXT100 DS25– –
Circular Connector Cable Assembly Terminal No.
Terminal no.
q
w
e
r
t
y
u
i
o
!0
!1
!2
!3
!4
!5
!6
!7
!8
!9
@0
@1
@2
@3
@4
@5
Lead wire color
Black
Brown
Red
Orange
Yellow
Pink
Blue
Purple
Gray
White
White
Yellow
Orange
Yellow
Pink
Blue
Purple
Gray
Orange
Red
Brown
Pink
Gray
Black
White
Dot marking
None
None
None
None
None
None
None
White
Black
Black
Red
Red
Red
Black
Black
White
None
None
Black
White
White
Red
Red
White
None
D-sub Connector Cable AssemblyTerminal No.
Item
Conductor resistance W/km, 20°C
Withstand voltage VAC, 1 min.
Insulation resistance, M/km, 20°C
Characteristics
65 or less
1000
5 or less
Circular Connector, D-sub Connector Cable AssemblyElectric Characteristics
Plug terminal no.(arrangement as seen from lead wire side)
q!5!4@4!3
!2 @3
@2!1
!0o i
@1
@6
@5
!6!7w
e
r!8
!9
y
t@0
u
1425
113 Multi-core vinyl cable
0.3 mm2 x 25C
2-M2.6 x 0.45
Terminalno.
Socket side
16
(60)
L
44L
8
47.0
4
50
" ø
10
Note) Terminal no.@6 is connected to @5 inside the connector.
L dimension1.5 m
3 m
5 m
L dimension
Series VQC
2-2-58
1_02_SV.qxd 04.6.16 14:30 Page 2-96
VV5QC41
nLL1L2
1131 185.5
2156 210.5
3181 235.5
4206 260.5
5231 285.5
6256 310.5
7281 335.5
8306 360.5
9331 385.5
10356 410.5
11381 435.5
12406 460.5
13431 485.5
14456 510.5
15481 535.5
16506 560.5
FormulasL1 = 25n + 106 (Maximum 16 single wiring stations)L2 = 25n + 160.5 n: Stations
Multiple connector cable assembly
Manual overrideIndicator light
n1 2 3 4 5 6 7StationsD-side 8 U-side
made by CONINVERS GmbH
Circular multiple connectors (26 pins) 3(R) port2-Rc 3/4
1(P) port2-Rc 1/2
Pilot exhaust port2-Rc 1/8External pilot port
2-Rc 1/8
M27 male screw
2n-Rc 1/4, 3/8, C8, C10, C12 <4(A), 2(B) port>
Rc 3/8: 3/8" Female threadC8 : ø8 One-touch fitting C10 : ø10 One-touch fitting C12 : ø12 One-touch fitting
Rc 1/4: 1/4" Female thread
A A AB AB
B
A
AB AB
B
A
B
A
B
A
B
A
AB
AA
SMC SMC SMC SMC SMC SMCSMC
L248 L1 6.5
65.5P=25
109
163
914
3
74.5
101
P=25 65.5
95.5
77.5
43.512
11.5
38.73127
21.5 (6.5)
20.5
42.7
18
60 15.7 2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2 B
4 A
2-2-61
Series VQCPlug-in Unit
Base Mounted
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
!1
!2
!6
!7
!8
!3
!4
Exploded View of Manifold
Manifold block assemblyD-side end plate assembly U-side end plate assemblyHousing assembly and SI unit
EX
500
EX
240
EX
126
EX
250
VQC1000VQC2000VQC4000
VQC1000VQC2000VQC4000
VQC4000
VQC1000VQC2000VQC4000
VQC1000VQC2000VQC4000
VQC1000VQC2000VQC4000
VQC1000VQC2000VQC4000
VQC1000VQC2000VQC4000
VQC1000VQC2000VQC4000
EX500
ÇìÇÖÇíÇâÇÖÇì
S K
it (
Ser
ial)
T K
it(T
erm
inal
blo
ck)
L K
it(L
ead
wir
e)M
Kit
(Mu
ltip
le c
on
nec
tor)
P K
it(F
lat
rib
bo
n c
able
)F
Kit
(D-s
ub
co
nn
ecto
r)
qw
e
r
t
y
u
i
o
!0
2-2-62
Note) VQC 4000 thread port only
VVQC 1 000-1A-- D -- C6
Thread type Note)
RcG
NPT/NPTF
NilFT
OptionNilR
S
Centralized exhaustExternal pilotDirect exhaust outlet with built-in silencer
Note) Tie-rods (2 pcs.) for additional sta-tions included.
Housing Assembly and SI Unit/Input Block
D-side end plate assembly Manifold block assembly
Manifold Assembly Part No.
Wiringspecifications
Double wiringSingle wiringNo wiring
SeriesVQC1000VQC2000
12
Kit typeS (EX240) kitF, P, T, S (EX250) kitL, M, S (EX500) kit
123
SeriesVQC1000VQC2000VQC4000
124
DS0 Note)
OptionNoneWith back pressure check valve
Nil
B Note)
OptionNilR
S
Centralized exhaustExternal pilotDirect exhaust outlet with built-in silencer
VVQC 1 000-2A-- 1 SeriesVQC1000VQC2000
12
Port size
U-side end plate assembly
VQC1000
VQC2000
SymbolC8C10C12N9N11N13
Port sizeVQC1000
VQC2000
VQC4000
SymbolC3C4C6C8C10C12N1N3N7N9N11M50203BC0
For ø3.2 One-touch fittingFor ø4 One-touch fittingFor ø6For ø8For ø10For ø12For ø1/8"For ø5/32"For ø1/4"For ø5/16"For ø3/8"For M5 threadRc 1/4"Rc 3/8"Rc 1/4" bottom portedWithout One-touch fitting
!6 D-side end plate assembly part no.
!8 U-side end plate assembly part no.
!7 Manifold block assembly part no.
Note) Except VQC4000.
VVQC4000-3A-- Thread typeNilFT
RcG
NPT/NPTF
RcG
NPT/NPTF
VVQC4000-2A-- 1 Thread type
NilFT
VQC4000
VQC4000
VQC1000/2000
VQC1000/2000
Port sizeVQC1000
VQC2000
SymbolC8C10N9N11
Supply/Exhaust portentry direction
1
2 Note)
Cylinder portsideBranch type
Note) VQC2000 only
VVQC 1 000-3A-1-- C8 --
1
---- C8Port size
Note) For VQC1000/2000 only.
Description NoteApplicable model
PROFIBUS-DP (–COM.)AS-i (–COM.)CC-LINK (+COM.)DeviceNet (–COM.)CANopen (–COM.)M12, 2 inputsM12, 4 inputsM8, 4 inputsStandardDIN rail mountingDeviceNet ( +COM.)Remote I/O (+COM.)DeviceNet / PROFIBUS-DP (–COM.)Remote I/O (–COM.)DeviceNet (+COM.)PROFIBUS-DP (–COM.)M12, 8 inputsFor manifold with input blockFor manifold without input blockCC-LINK (+COM.)For EX126 SI unit mountingF kit, 25 pinsP kit, 26 pinsP kit, 20 pinsT kitL kit with 0.6 m lead wireL kit with 1.5 m lead wireL kit with 3.0 m lead wireM kit 26 pinsDouble wiring of 1st to 8th stationsDouble wiring of 9th to 12th stations
SI unit
Input block
End plate assembly
SI unit
SI unit
Input block
End cover assembly
SI unitTerminal plateD-sub connector housing assembly
Flat ribbon cable housing assembly
Terminal block box housing assembly
Lead wire housing assembly
Multiple connector housing assembly
Signal cut block
Part no.
EX250-SPR1EX250-SASEX250-SMJEX250-SDN1EX250-SCA1EX250-IE1EX250-IE2EX250-IE3EX250-EA1EX250-EA2EX500-Q001EX500-Q001-X1EX500-Q101EX500-Q101-X1EX240-SDN2EX240-SPR1EX240-IE1EX240-EA2EX240-EA4EX126D-SMJ1VVQC1000-74A-2VVQC1000-F25-1VVQC1000-P26-1VVQC1000-P20-1VVQC1000-T0-1VVQC1000-L25-0-1VVQC1000-L25-1-1VVQC1000-L25-2-1VVQC1000-M26-1EX9-SC1-8EX9-SC2-4
VQC1000
———
VQC2000
———
VQC4000—
No.
—
—
q
w
e
r
t
y
u
i
o
!0
!1
!2
!3
!4
!5
2-2-63
Exploded View of Manifold
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD
EX500
ÇìÇÖÇíÇâÇÖÇì