Upload
hoangdang
View
232
Download
2
Embed Size (px)
Citation preview
First Issue dated 03/03/2003 Rev.3 dated 23/09/2010 Page 1 of 11
vulcanair spa via g. pascoli, 7 80026 casoria (na) – italia Tel +39 081 5918111 Fax +39 081 5918172 [email protected] www.vulcanair.com
AP68TP VARIANTS
Approved by the Vulcanair Design Organisation
The technical content of this document is approved under the authority of DOA No. EASA.21J.009. Operator obligations with regards to inspections, modifications and/or other technical directives and their times of compliance are laid out in the relative Airworthiness Directives.
SERVICE BULLETIN No. TP-14 Rev. 3
(Supersedes the previous issue dated 20/07/2006)
Design Organisation Approval No. AS-SB/10/018 dated 25/10/2010
M A N D A T O R Y SUBJECT: Transmission of Technical Documentation issued by “Parker
Hannifin - Nichols Airborne” and “Rapco Inc.” - VACUUM SYSTEM
NOTE: This Revision to SB TP-14 has been issued with the purpose of updating the Service Life Limits and the Inspection Intervals for vacuum pumps manufactured by “Parker Hannifin - Nichols Airborne” and by “Rapco Inc.”
1. GENERAL
1.1 AIRCRAFT AFFECTED All AP68TP variants aircraft.
Vulcanair spa Service Bulletin No. TP-14
First Issue dated 03/03/2003 Rev. 3 dated 23/09/2010 Page 2 of 11
1. GENERAL (Cont.)
1.2 PURPOSE The purpose of this Service Bulletin is:
a) Reference Part A of Paragraph 2.
To transmit the Technical Documentation issued by “Parker Hannifin - Nichols Airborne Division” (Ref. paragraph 1.3) regarding the items contained in the cross-reference table in Part B of paragraph 2.
b) Reference Part B of Paragraph 2.
To supply instructions for the replacement of Parker/Airborne items, no longer available, with new interchangeable items in accordance with the cross-reference table in Part B of paragraph 2.
c) Reference Part C of Paragraph 2.
To transmit the Technical Documentation issued by “Rapco Inc.” (Ref. paragraph 1.3) and to supply instructions for updating the Service Life Limits, the Scheduled Maintenance Checks and Procedures for aircraft incorporating Part B of this SB.
d) Reference Part D of Paragraph 2.
To supply the procedures to carry out the wear check using the “RAPCO SMART STICK” and the check for oil contamination of the RAPCO Vacuum Pump P/N RA442CW.
e) Reference Part E of Paragraph 2.
To provide the procedure to carry out an efficiency check of the Vacuum System. 1.3 DESCRIPTION
The following Technical Documentation issued by “Parker Hannifin - Nichols Airborne” is attached herewith: • Service Letter 39A – Mandatory Inspection Intervals and Replacement Times for
Airborne Check Valve Manifolds, Check Valves and Regulator Check Valve Manifolds.
• Service Letter 66 – Mandatory Inspection and Replacement for Overhauled or Reconditioned Parker/Airborne Air Pumps, Pneumatic System Valves and Check Valves Manifolds.
• Service Letter 72 – All Parker/Airborne Engine-Driven Air Pumps are beyond their Mandatory Replacement Time and must be removed from service.
Vulcanair spa Service Bulletin No. TP-14
First Issue dated 03/03/2003 Rev. 3 dated 23/09/2010 Page 3 of 11
1.3 DESCRIPTION (Cont.)
The following Technical Documentation issued by “Rapco Inc.” is attached herewith: • Service Letter RASL-001 – Pneumatic pump vane inspection with SMART Stick. • Service Letter RASL-003 – Mandatory Pneumatic Pump Replacement after being
subjected to Sudden Engine Stoppage. • Service Letter RASL-005 – Recommended replacement for Rapco Inc. pneumatic
pumps.
1.4 COMPLIANCE Part A of Paragraph 2: As required by “Parker Hannifin - Nichols Airborne” (refer to
the attached Parker/Airborne documentation); Part B of Paragraph 2: As required by “Parker Hannifin - Nichols Airborne” (refer to
the attached Parker/Airborne documentation);
1.5 TIME REQUIRED Part D of Paragraph 2: 6 man-hours; Part E of Paragraph 2: 4 man-hours.
1.6 SPECIAL TOOLS Part A of Paragraph 2: As required by Parker Hannifin Corporation – Nichols Airborne
(refer to attached Parker-Airborne documentation); Part B of Paragraph 2: No special tools are required; Part D of Paragraph 2: RAPCO SMART STICK (supplied by Rapco together with each Vacuum Pump); Part E of Paragraph 2: No special tools are required.
1.7 VARIATION IN WEIGHT & BALANCE Part A of Paragraph 2: Not applicable; Part B of Paragraph 2: Negligible.
1.8 ELECTRICAL SYSTEM LOAD Not Applicable.
1.9 REFERENCE DOCUMENTS Applicable Parts Catalogue for aircraft variant; Applicable Maintenance Manual for Aircraft variant.
1.10 PUBLICATIONS AFFECTED Applicable Maintenance Manual for Aircraft variant.
1.11 APPLICATION TO BE CARRIED OUT BY Certified Maintenance Facility.
Vulcanair spa Service Bulletin No. TP-14
First Issue dated 03/03/2003 Rev. 3 dated 23/09/2010 Page 4 of 11
2. WORK PROCEDURE
PART A Application of Service Letters issued by Parker Hannifin – Nichols Airborne (Refer to list in paragraph 1.3).
1. Identify the Parker/Airborne items through the identification placard installed on each item. 2. Remove from service Vacuum Pump P/N 442CW, as per Parker/Airborne Service Letter 72,
and replace it with new Rapco Vacuum Pump P/N RA442CW. 3. Carry out the mandatory annual inspection on Manifold Check Valve P/N 1H5-1 required by
Parker/Airborne Service Letter 39A if it has not still reach its Service Life Limit (10 years from the date of manufacture), as per Service Letter 39A.
4. Overhauled or reconditioned Parker/Airborne items must not be used and must be replaced
immediately with new corresponding Rapco items, as per Service Letter 66.
5. Carry out a functional check of the Vacuum System in accordance with the procedure contained in Part E of this SB, if vacuum system items have been replaced.
6. Record compliance with Part A of this SB in the aircraft Log-Book, detailing the results of
inspections required by Parker Hannifin - Nichols Airborne and the replaced items.
Vulcanair spa Service Bulletin No. TP-14
First Issue dated 03/03/2003 Rev. 3 dated 23/09/2010 Page 5 of 11
2. WORK PROCEDURE (Cont.) PART B Replacement of Parker/Airborne items, no longer available, with new items manufactured by Rapco Inc., in accordance with the following cross-reference table:
Vulcanair P/N Description Parker P/N Rapco P/N Applicability
NOR7.289-5 Vacuum Pump 442CW RA442CW Vacuum System - AP68TP aircraft variants
NOR7.283-3 Manifold Check Valve 1H5-1 RA1H5-1 Vacuum System - AP68TP aircraft variants
NOTE: The new Rapco Vacuum Pump is fully interchangeable with respect to the previous
Parker/Airborne item. Therefore its installation requires a simple removal/installation operation.
Instructions 1. Replace the Parker/Airborne Vacuum Pump P/N 442CW with the new Rapco Vacuum Pump
P/N RA442CW, in accordance with the above cross-reference table. Refer to the manufacturer instructions for removal / installation procedures.
2. Replace the Parker/Airborne Manifold Check Valve P/N 1H5-1 with the new Rapco
Manifold Check Valve P/N RA1H5-1, in accordance with the above cross-reference table, if Parker/Airborne one has reached its Service Life Limit (10 years from the date of manufacture). Refer to the manufacturer instructions for removal / installation procedures.
3. Carry out a functional check of the Vacuum System in accordance with the procedure
contained in the Part E of this SB.
4. Record compliance with Part B of this SB in the Aircraft Log-Book, detailing the Part Numbers of the replaced items.
Vulcanair spa Service Bulletin No. TP-14
First Issue dated 03/03/2003 Rev. 3 dated 23/09/2010 Page 6 of 11
2. WORK PROCEDURE (Cont.) PART C
Updating of the Service Life Limits, the Scheduled Maintenance Checks and Procedures for aircraft incorporating Part B of this SB (Installation of items manufactured by Rapco). Service Life Limits:
Vulcanair P/N Description Rapco P/N Service Life Limits Applicability
NOR7.289-5 Vacuum Pump RA442CW
Replace after 6 years from the date of installation (refer to Service Letter RASL-005) or when it is found not serviceable for wear limits, as per Service Letter RASL-001.
NOTE: Each Vacuum Pump that has been subjected or is suspected to have been subjected to sudden engine stoppage or propeller strike event (refer to Service Letter RASL-003) or that has been contaminated by oil must be replaced before the next flight.
AP68TP aircraft variants
NOR7.283-3 Manifold Check Valve RA1H5-1
Replace every 2000 flight hours or 7 years from the date of manufacture, whichever occurs first.
AP68TP aircraft variants
Scheduled Maintenance Checks:
Vulcanair P/N Description Rapco P/N Inspection Intervals
NOR7.289-5 Vacuum Pump RA442CW
Inspection for wear limits (as per Service Letter RASL-001): First inspection: after 200 Flight Hours; Repetitive Inspections: every 100 Flight Hours or 1 year (whichever occurs first). Carry out the Vacuum Pump wear check using the “RAPCO SMART STICK” in accordance with the procedure contained in subparagraph a) of Part D hereunder.
Inspection for oil contamination: Every 100 Flight Hours or 1 year (whichever occurs first) in accordance with the procedure contained in subparagraph b) of Part D hereunder.
Vulcanair spa Service Bulletin No. TP-14
First Issue dated 03/03/2003 Rev. 3 dated 23/09/2010 Page 7 of 11
2. WORK PROCEDURE (Cont.) PART D
a) Procedure to check the Rapco Vacuum Pump P/N RA442CW for wear limits using the “RAPCO SMART STICK” (Refer to Figures 1, 2, 3, 4 and Rapco Service Letter RASL-001)
1. Place OFF all electrical switches; 2. With reference to the applicable section of the Aircraft Maintenance Manual, remove the
engine cowlings to gain access to the concerned area; 3. Push the sleeve all the way to the shoulder (Worn area) (See Fig. 2); 4. Remove the cap screw and lock washer from pump (See Fig. 1); 5. Rotate prop slowly and look into hole with flashlight to line up vane with hole; 6. Insert the SMART STICK to verify alignment; 7. Remove the SMART STICK from pump; 8. Push down the sleeve until about ¼ inch from tip (See Fig. 3); 9. Push in the SMART STICK slowly until it stops; 10. Make sure that wear sleeve is touching pump; 11. Pull the SMART STICK out of pump and compare position of the wear sleeve with Fig. 4;
NOTE: With reference to Figure 4, replace any Vacuum Pump which results worn-out. Contact Vulcanair Sales Department or RAPCO Inc. directly to obtain a new Vacuum
Pump.
12. Re-install the cap screw and lock washer as previously: torque to 14 in-lbs; 13. Re-install all removed engine cowlings.
Fig. 1
Vulcanair spa Service Bulletin No. TP-14
First Issue dated 03/03/2003 Rev. 3 dated 23/09/2010 Page 8 of 11
2. WORK PROCEDURE (Cont.) PART D (cont.)
Fig. 2 Fig. 3
Fig. 4 Vacuum Pump wear status check with “RAPCO SMART STICK”
Wear sleeve position prior to verifying line up vane with
wear inspection hole
Wear sleeve position prior to performing pump wear
check
Vulcanair spa Service Bulletin No. TP-14
First Issue dated 03/03/2003 Rev. 3 dated 23/09/2010 Page 9 of 11
2. WORK PROCEDURE (Cont.) PART D (Cont.)
b) Procedure to check the Rapco Vacuum Pump P/N RA442CW for oil contamination
At inspection intervals laid out in the Scheduled Maintenance Checks in Part C of Paragraph 2, inspect the vacuum pump for oil contamination in accordance with the following procedure:
1. Place all electrical switches OFF; 2. With reference to the applicable section of the Aircraft Maintenance Manual, remove the
engine cowlings to gain access to the concerned area; 3. Inspect the area around the AND20000 accessory pad and lower surfaces of the vacuum
pump for evidence of oil; if evidence of oil is discovered, follow the instructions below:
Problem: AND20000 accessory pad drive-shaft oil seal leaking.
Corrective action: replace the AND20000 accessory pad drive shaft oil seal in accordance with the instructions provided by the Engine Manufacturer in the appropriate maintenance pubblication.
Problem: Vacuum pump mounting gasket leaking.
Corrective action: Mandatory gasket replacement. Install a new vacuum pump mounting gasket in accordance with the instructions in the applicable relevant documentation.
Problem: Any oil in the vacuum pump drive and mounting area. Remove the vacuum pump and perform a visual inspection of the pump drive end and mounting area, no oil is permitted (refer to Figure 5). Reinstall any vacuum pump not contaminated by oil as before.
Corrective action: Mandatory vacuum pump replacement. Install the new vacuum pump in accordance with the instructions in the applicable relevant documentation.
Vulcanair spa Service Bulletin No. TP-14
First Issue dated 03/03/2003 Rev. 3 dated 23/09/2010 Page 10 of 11
2. WORK PROCEDURE (Cont.) PART D (Cont.)
Fig. 5
4. Inspect the engine compartment for evidence of any other oil leaks, i.e., fittings, hoses gaskets, etc. Replace or repair as required.
CAUTION: Failure to correct oil leaks may allow oil to enter the air pump and cause premature air pump failure.
5. Re-install all removed engine cowlings.
Vulcanair spa Service Bulletin No. TP-14
First Issue dated 03/03/2003 Rev. 3 dated 23/09/2010 Page 11 of 11
2. WORK PROCEDURE (Cont.) PART E Efficiency Check of the Vacuum System 1. Place the aircraft in a designated engine test area; 2. Chock the wheels and set the parking brake ON; 3. Start both engines and run at IDLE speed; 4. Conduct an Efficiency Check of the Vacuum System on ground under the different
conditions listed in the chart hereunder; 5. Record the values obtained on the chart, in the columns from 1 to 4 on the line stating
“Vacuum (On Ground)”; 6. If the values obtained do not correspond with the estimated values, check the vacuum
system lines for leaks in the connections carried out.
VACUUM SYSTEM EFFICIENCY TEST CHART TEST
CONDITIONS 1 2 3 4
LH ENGINE IDLE IDLE 100% NP 100% NP RH ENGINE IDLE 100% NP IDLE 100% NP SYSTEM RESPONSE
4,5-5,2 inHg
4,5-5,2 inHg
4,5-5,2 inHg
4,5-5,2 inHg
VACUUM (ON GROUND)
3. MATERIALS REQUIRED FOR THE MODIFICATION
Refer to cross-reference table in Part B of paragraph 2.
NOTE: Contact Vulcanair Sales Department or the manufacturers directly, to obtain the necessary spare parts:
RAPCO, Inc. Replacement Aircraft Parts Co. 445 Cardinal Lane Hartland, WI 53029 USA Phone: (262) 367-2292 Fax: (262) 367-7158 www.rapco-rfs.com
Parker Hannifin Corporation Nichols Airborne Division 711 Taylor Street Elyria, OH 44035 USA Phone: (440) 284-6215 Fax: (440) 284-6208 www.parker.com/ag/nad
Parker/Airborne Division • Parker Hannifin Corporation 711 Taylor Street • Elyria, Ohio 44035 • 440 284-6215 • Fax: 440 284-6208E-mail: [email protected] • Website: www.parker.com/ag/nad
(Page 1 of 6)
Service Letter No: 66
Date: January 31, 2007
Subject: Mandatory Inspection and Replacement for Overhauled or Reconditioned Parker/Airborne
Air Pumps, Pneumatic System Valves and Check Valve Manifolds
Applicability:
This Service Letter applies to all aircraft with pneumatic systems powering critical flight instruments (e.g. pneumatic
powered artificial horizon and/or pneumatic powered directional indicator) and/or deice boots. This Service Letter
applies to all Parker/Airborne component model numbers. A list of these model numbers is provided below.
Applicable Parker/Airborne Model Numbers:
Air Pumps:
Any model beginning with 211 through 216, 241 through 242, 441 through 442, 842, 28C214, 28C444, 4A2
or 4A3.
Check Valves, Check Valve Manifolds and Regulator Check Valve Manifolds:
Any model beginning with 1H5, 1H24, 1H37, 2H24 and models 2H3-39 or 2H3-47.
Vacuum Regulators and Pressure Regulators:
Any model number beginning with 2H3 or 2H30.
Pneumatic System Valves:
Any model beginning with 1H27, 1H43, 1H44, 1H47, 1H51, 1H52, 1H53, 2H22, 2H48, 2H59 or 2H86.
Background:
The pneumatic system which powers flight instruments and/or deice boots on aircraft which fly Instrument Flight
Rules (IFR) is critical to the safety of the pilot and the passengers. If any component of the pneumatic system fails
during Instrument Meteorological Conditions (IMC) and the pilot is not proficient in using partial panel instruments, the
pilot may become spatially disoriented and may not be able to control the aircraft, resulting in loss of life for the pilot
and the passengers.
Parker/Airborne pneumatic components are not designed to be overhauled or reconditioned, and no parts of any of
these components (including the outer housing and any of the internal parts) can be reused. Parker/Airborne has not
and does not overhaul or recondition pneumatic components. Parker/Airborne does not supply any parts, drawings,
instructions, specifications or approvals for the overhaul or recondition of its pneumatic components.
The parts comprising Parker/Airborne air pumps and/or pneumatic components were designed and manufactured
with tolerances to specific proprietary dimensions and distinct materials to meet performance specifications. These
parts were individually measured, categorized and placed in matched sets to ensure the component meets
Service Letter Number: 66 (continued)
(Page 2 of 6)
Parker/Airborne Division Parker Hannifin Corporation711 Taylor Street Elyria, Ohio 44035 440 284-6215 Fax: 440 284-6208
pneumatic system performance requirement. Therefore, Parker/Airborne parts only precisely fit with otherParker/Airborne parts of the same matched set and manufacture.
Overhauled and reconditioned air pumps and/or pneumatic components are not authorized by Parker/Airborne andcan include mixed parts from various vintage Parker/Airborne components, parts made by others, and parts fromvarious components with undocumented history and undocumented traceability. Overhauled or reconditionedParker/Airborne pneumatic components must not be used and can result in the loss or inadequate operation of gyrosand deice boot inflation.
Compliance:
Compliance with the following is mandatory.
Within the next 30 days, inspect your aircraft for overhauled or reconditioned Parker/Airborne PneumaticComponents. In order to ensure continued compliance with this Service Letter, continue to inspect your aircraft foroverhauled or reconditioned Parker/Airborne components during the annual aircraft inspection. If your aircraft’spneumatic system contains an overhauled or reconditioned Parker/Airborne Pneumatic Component, replace the unitwith a NEW one before the aircraft is flown IFR.
A. How To Identify Overhauled Or Reconditioned Parker/Airborne Air Pumps.
The information below should be used as a guide in determining if you have an overhauled or reconditionedParker/Airborne air pump. Refer to the applicability section on the first page of this Service Letter forapplicable Parker/Airborne model numbers.
1. Nameplates – Overhaulers, in most cases, remove the Parker/Airborne nameplate and install one oftheir own design which indicates “Manufacturer: Airborne” and may or may not identify the overhauler.Parker/Airborne nameplates will always have either an Airborne or Parker Logo. Overhaulers assigntheir own serial numbers which have a different format than Parker/Airborne. Parker/Airborne serialnumbers consist of a combination of numbers and letters. The first numbers (1 through 12) indicate themonth of manufacture (January through December). The next or two letters indicate the year ofmanufacture followed by the unit number.
Parker/Airborne example: 11AU123. Overhauler examples: 38956, 25AK364
Parker/Airborne Division • Parker Hannifin Corporation 711 Taylor Street • Elyria, Ohio 44035 • 440 284-6215 • Fax: 440 284-6208E-mail: [email protected] • Website: www.parker.com/ag/nad
SAFETY WARNING:
FAILURE OF AN OVERHAULED OR RECONDITIONED PARKER/AIRBORNE PNEUMATIC COMPONENT ESPECIALLY WHILE FLYING IN INSTRUMENT METEOROLOGICAL CONDITIONS (IMC) CAN LEAD TO SPATIAL DISORIENTATION OF THE PILOT AND SUBSEQUENT LOSS OF AIRCRAFT CONTROL RESULTING IN DEATH, BODILY INJURY OR PROPERTY DAMAGE. OVERHAULED OR RECONDITIONED PARKER/AIRBORNE PNEUMATIC COMPONENTS MUST NOT BE USED AND MUST BE REPLACED IMMEDIATELY WITH A NEW COMPONENT.
Parker/Airborne Division • Parker Hannifin Corporation 711 Taylor Street • Elyria, Ohio 44035 • 440 284-6215 • Fax: 440 284-6208E-mail: [email protected] • Website: www.parker.com/ag/nad
Service Letter Number: 66 (continued)
(Page 3 of 6)
Parker/Airborne Division • Parker Hannifin Corporation711 Taylor Street • Elyria, Ohio 44035 • 440 284-6215 • Fax: 440 284-6208
Typical Parker/Airborne air pump nameplates
Typical overhauled or reconditioned nameplates
OVERHAUL BY
xxxxx xxxxx, INC.
P/N _______________
S/N ___xxxxxx______
PROC. SPEC. #xxxxxxxxxxxx
O.E.M. AIRBORNE
CITY, STATE
FAA CRS #xxxxxxxxxxxx
Parker Logo
Airborne Logo
No Logo
Overhauler
Identification
Model No.ManufacturerAirborne
Part Name
Dry Air Pump
Ser. No.
ManufacturerAirborne
Part Name
Dry Air Pump
No Overhauler
Identification
Model No.
FAA PMA
Ser. No.
xxxxxx
Parker Logo
Non-Airborne
Serial Number
Airborne Serial
Number
XXXXX
Service Letter Number: 66 (continued)
(Page 4 of 6)
Parker/Airborne Division • Parker Hannifin Corporation711 Taylor Street • Elyria, Ohio 44035 • 440 284-6215 • Fax: 440 284-6208
2. “No Overhaul” Labeling - Parker/Airborne has cast into the mounting flange and back flange of our air
pumps “NO OVERHAUL”, since 1986. Overhaulers, in some cases, cover the “NO OVERHAUL” on
the back flange with labels stating “FAA APPROVED OVERHAUL” or “RETURNABLE CORE”. Check to
see if the air pump includes “NO OVERHAUL” cast into the housing and also a label stating “FAA
APPROVED OVERHAUL” or “RETURNABLE CORE”.
Back End of Parker/Airborne Pump Parker/Airborne Pump
Overhauled Parker/Airborne Pump Overhauled Parker/Airborne Pump
Cast into housings
since 1986
Cast into housings
since 1986
FAA APPROVED
OVERHAUL
Overhauler’s label,
sometimes used to cover
Parker/Airborne’s “No-
Overhaul” warning
Overhaulers
Label
Parker/Airborne Division • Parker Hannifin Corporation 711 Taylor Street • Elyria, Ohio 44035 • 440 284-6215 • Fax: 440 284-6208E-mail: [email protected] • Website: www.parker.com/ag/nad
Service Letter Number: 66 (continued)
(Page 5 of 6)
Parker/Airborne Division • Parker Hannifin Corporation711 Taylor Street • Elyria, Ohio 44035 • 440 284-6215 • Fax: 440 284-6208
3. Torque Putty - Torque putty is used on one fastener of each end of the air pump. Overhaulers use
colored torque putty while Parker Airborne has always used white torque putty. Parker/Airborne torque
putty may discolor with age and/or temperature, changing from white to tan.
4. Painting - Some Overhaulers paint the entire pump black to cover the coloring of various vintage parts
used.
5. Anti-Vise Label – Overhaulers use a smooth plastic anti-vise label where Parker/Airborne always used
a fabric material anti-vise label. The fabric weave in the Parker/Airborne material is visible.
6. Log Book Review - Review log books for entries identifying installation of overhauled or reconditioned
air pumps.
Parker/Airborne Division • Parker Hannifin Corporation 711 Taylor Street • Elyria, Ohio 44035 • 440 284-6215 • Fax: 440 284-6208E-mail: [email protected] • Website: www.parker.com/ag/nad
TorquePutty
TorquePutty
Back End of Parker/Airborne Pump Front End of Parker/Airborne Pump
Parker/Airborne Division • Parker Hannifin Corporation 711 Taylor Street • Elyria, Ohio 44035 • 440 284-6215 • Fax: 440 284-6208E-mail: [email protected] • Website: www.parker.com/ag/nad
Service Letter Number: 66 (continued)
(Page 6 of 6)
Parker/Airborne Division Parker Hannifin Corporation711 Taylor Street Elyria, Ohio 44035 440 284-6215 Fax: 440 284-6208
B. How To Identify Overhauled Or Reconditioned Parker/Airborne Pneumatic System Valvesor Check Valve Manifolds
The information below should be used as a guide in determining if you have an overhauled or reconditionedParker/Airborne pneumatic system valve or check valve manifold. Refer to the applicability section on thefirst page of this Service Letter for applicable Parker/Airborne model numbers.
The easiest way to identify if a Parker/Airborne pneumatic system valve or check valve manifold has beenoverhauled or reconditioned is by examining the rivets used. Based on the overhauled or reconditionedvalves and manifolds that Parker/Airborne has examined to date, overhauled or reconditioned units arereassembled with “solid” rivets. Parker/Airborne only uses “tubular” rivets on these assemblies.
Cross-Section Parker/Airborne’s Tubular Rivet Cross-Section Overhauler’s Solid Rivet
Summary:
Promptly and regularly inspect your aircraft for overhauled or reconditioned Parker/Airborne pneumatic components.If you determine that your air pump or pneumatic component is an overhauled or reconditioned Parker/Airbornecomponent, then immediately replace it with a new component. If, after following the above component identificationmethods, you cannot determine whether your Parker/Airborne component has been overhauled, or if you cannotdetermine the history of the component, then immediately replace it with a new component.
Parker/Airborne realizes that owners and operators of aircraft have the choice of purchasing a new oroverhauled/reconditioned air pump, pneumatic system valve, and check valve manifold. However, aircraftowners/operators/pilots should be aware of the increased risk of pneumatic system failure when using overhauled orreconditioned Parker/Airborne pneumatic components. An overhauled or reconditioned Parker/Airborne pneumaticcomponent must not be used. Any time a Parker/Airborne pneumatic component is replaced, a new one must beused.
Any questions concerning this Service Letter or requests for free copies of any Parker/Airborne Service Letters(which can also be printed from Parker/Airborne’s website) should be directed to Parker/Airborne Customer SupportTeam as follows:
Toll Free Phone Number: 800-382-8422
Direct Phone Number: 440-284-6215
FAX Number: 440-284-6208
E-Mail:
Website:
HOLLOW SOLID
RIVET HEADRIVET HEAD
VALVE
FLANGE
VALVE
FLANGE
GASKET OR
DIAPHRAGM
GASKET OR
DIAPHRAGM
www.parker.com/ag/nad
Nichols Airborne Division • Parker Hannifin Corporation 711 Taylor Street • Elyria, Ohio 44035 • 440 284-6215 • Fax: 440 284-6208E-mail: [email protected] • Website: www.parker.com/ag/nad
(Page 1 of 2)
Service Letter Number: 72 (Supersedes Service Letters 17B, 38A, 43A, 53C and 54D)
Date: February 15, 2008
Subject: All Parker/Airborne Engine-Driven Air Pumps are beyond their Mandatory Replacement Time and must be removed from service.
Applicability:
This Service Letter applies to all aircraft using Parker/Airborne Engine-Driven Air Pumps in pneumatic systems which power critical gyro flight instruments (e.g. artificial horizon instruments, directional indicator instruments) and/or deice boots. This Service Letter applies to ALL Parker/Airborne Engine-Driven Air Pump model numbers. For your reference these model numbers are:
Any model beginning with 200 through 216, E211 through E212, 220 through 242, 420 through 442, 832, 842, 28C214 or 28C444.
Background:
The pneumatic system which powers gyro flight instruments and/or deice boots on aircraft which fly Instrument Flight Rules (IFR) is critical to the safety of the pilot and the passengers. If any component of the pneumatic system fails during Instrument Meteorological Conditions (IMC) and the pilot is not proficient in using partial panel instruments, the pilot may become spatially disoriented and may not be able to control the aircraft. This could result in the loss of life for the pilot and the passengers.
Parker/Airborne ceased the manufacture of Engine-Driven Air Pumps in February 2002. Parker/Airborne Engine-Driven Air Pumps have a Mandatory Replacement Time of 6 years from date of manufacture. Thus, ALL Parker/Airborne Engine-Driven Air Pumps are beyond their Mandatory Replacement Time and must be removed from service.
Compliance:
Compliance with the following is mandatory.
Within the next 30 days, inspect your aircraft for Parker/Airborne Engine-Driven Air Pumps. IF YOUR AIRCRAFT’S PNEUMATIC SYSTEM CONTAINS A PARKER/AIRBORNE ENGINE-DRIVEN AIR PUMP, REMOVE THE UNIT BEFORE NEXT FLIGHT. In order to ensure continued compliance with this Service Letter, continue to inspect your aircraft for Parker/Airborne Engine-Driven Air Pumps during subsequent annual inspections. Contact the manufacturer of your aircraft for the appropriate replacement for your Parker/Airborne engine-driven air pump.
This Service Letter contains information CRITICAL TO PILOT AND PASSENGER SAFETY! Read COMPLETELY and comply with all directives immediately.
Nichols Airborne Division • Parker Hannifin Corporation 711 Taylor Street • Elyria, Ohio 44035 • 440 284-6215 • Fax: 440 284-6208E-mail: [email protected] • Website: www.parker.com/ag/nad
(Page 2 of 2)
Service Letter Number: 72 (continued)
Approval:
The technical content of this Service Letter that affects Type Design is FAA approved.
Reminder:
Parker/Airborne realizes that owners and operators of aircraft have the choice of purchasing a new or overhauled/reconditioned engine-driven air pump. However, aircraft owners/operators/pilots should be aware of the increased risk of pneumatic system failure when using overhauled or reconditioned Parker/Airborne engine-driven air pumps. An overhauled or reconditioned Parker/Airborne engine-driven air pump must not be used. Any time a Parker/Airborne engine-driven air pump is removed, contact the manufacturer of your aircraft for the appropriate replacement.
Refer to: Service Letter Number 66 - Mandatory Inspection and Replacement of Overhauled or Field Reconditioned Parker/Airborne Air Pumps, Pneumatic System Valves and Check Valve Manifolds.
Superseded Parker/Airborne Service Letters:
The following Parker/Airborne Service Letters are superseded by this Service Letter Number 72, the removal of all Parker/Airborne engine-driven air pumps from service:
Service Letter Number 17B – Dry Air Pump Coupling Service Life Limitation.
Service Letter Number 38A – Mandatory Replacement of Airborne Engine-Driven Air Pumps that Have Been Subjected to Sudden Engine Stoppage.
Service Letter Number 43A – Mandatory Inspection Intervals for Airborne Air Pumps for Oil Contamination and Mandatory Replacement of OIL Contaminated Air Pumps.
Service Letter Number 53C – Mandatory Inspection Intervals and Replacement Times for 28C444CW-6 Engine Driven Clutch Operated Air Pumps.
Service Letter Number 54D – Mandatory Inspection Intervals and Replacement Times for 28C214CW-2 Engine Driven Clutch Operated Air Pumps.
Any questions concerning this Service Letter or requests for copies of any Airborne Service Letters (can also be printed from Airborne’s website) should be directed to Airborne’s Customer Support Team as follows:
Toll Free Phone Number: 800-382-8422 Direct Phone Number: 440-284-6215 Fax Number: 440-284-6208 E-Mail: [email protected] Website: www.parker.com/ag/nad
This document may be reproduced and distributed as deemed necessary.
Service Letter
445 Cardinal Lane
Hartland, WI 53029 (262) 367-2292
www.rapcoinc.com
Service letter Number Issue Date Revision Revision Date RASL-001 4/13/2004 C 6/11/2009
Subject: Pneumatic pump vane inspection with S.M.A.R.T Stick Applicability: This inspection procedure applies to all new FAA PMA approved pneumatic pumps manufactured by Rapco, Inc. that are equipped with a vane wear inspection port. Inspection Compliance: The inspection procedure listed below should be accomplished after 500 hours time in service on all 200 series pumps and after 200 hours time in service on all 400 series pumps. After the initial inspection, the pump should be re-inspected after 100 hours time in service or annually (which ever occurs first). This inspection procedure is recommended to be accomplished in conjunction with a 100 hour or annual inspection. NOTE: No other vane wear measuring devices are approved for use with this inspection procedure. Procedure: NOTE: Before accomplishing this inspection it is important to make sure that the Aircraft Engine Magnetos are in the off position.
1. Remove inspection port cap screw and lock washer. 2. Rotate Propeller by hand while looking into the inspection port with a flashlight. 3. Line up a vane slot with the inspection port. NOTE: If vane slot to inspection port alignment is incorrect it
will result in an incorrect vane wear measurement. 4. Remove the S.M.A.R.T stick wear sleeve from the S.M.A.R.T stick handle and place it on the S.M.A.R.T
stick probe end. Leave about ¼” of the probe end exposed. 5. Holding the handle of the S.M.A.R.T stick, push the probe into the inspection port slowly until it comes into
contact with the vane face. NOTE: The S.M.A.R.T stick wear sleeve will slide on the S.M.A.R.T stick probe during this process. Be sure that the S.M.A.R.T sleeve is in contact with the pump cavity.
6. Remove the S.M.A.R.T stick from the inspection port. 7. Read the position of the wear sleeve. (See figures below) 8. Determine if pump is within serviceable limits. 9. If the pump is determined not to be within serviceable limits it should be removed from service. If pump
is determined to be serviceable, it may be returned to service pending that the next inspection is accomplished after 100 hours time in service or at the next annual inspection.
10. Re-install cap screw and washer (MS35338-43) and torque to 14 inch lbs.
S.M.A.R.T Stick U.S Patent No.: US 7,216,526 B2
Improper Installation Proper Installation Proper Installation No Proof Mark Visible Wear Sleeve is Between Proof Mark and Shoulder Wear Sleeve is Touching Shoulder
Re-align vane slot to inspection port Pump wear is within Serviceable Limits Pump is worn beyond Serviceable limits and re-install S.M.A.R.T Stick Ok to Return Pump to Service Remove Pump from Service
Proof MarkShoulder Wear Sleeve
Service Letter
445 Cardinal Lane
Hartland, WI 53029 (262) 367-2292
www.rapcoinc.com
Service letter Number Issue Date Revision Revision Date RASL-003 11/14/2007 - -
Subject: Mandatory Pneumatic Pump Replacement after being subjected to Sudden Engine Stoppage. Applicability: This procedure applies to all new FAA PMA approved pneumatic pumps manufactured by Rapco, Inc. and all pneumatic pumps that have been overhauled by Rapco, Inc when installed on single-engine and multi-engine aircraft applications. Compliance: When a Rapco, Inc pneumatic pump has been subjected or is suspected to have been subjected to sudden engine stoppage or propeller strike event, it is Mandatory that the effected pneumatic pump be replaced before further flight in accordance with the procedure outlined below. Procedure:
1) Remove damaged pneumatic pump in accordance with the aircraft manufacturer’s service instructions.
2) Replace damaged pneumatic pump with a Rapco, Inc. new FAA PMA approved or
overhauled pneumatic pump.
3) Install new pneumatic pump in accordance with the aircraft manufactures service instructions.
4) Complete aircraft maintenance log book entry for the work accomplished. Include a
statement that shows compliance with this service letter. Note: If you have any questions regarding this Service Letter please feel free to contact us.
Service Letter
445 Cardinal Lane
Hartland, WI 53029 (262) 367-2292
www.rapcoinc.com
Service letter Number Issue Date Revision Revision Date RASL-005 6/24/2009 B 12/7/2009
Subject: Recommended replacement for Rapco, Inc. pneumatic pumps. Applicability: This service letter is applicable to all new FAA PMA approved pneumatic pumps manufactured by Rapco, Inc. and any pneumatic pumps overhauled by Rapco, Inc. Note: The information contained in this document is for reference only. Please refer to the applicable TCDS holder’s maintenance manual for specific mandatory requirements. Purpose: This document was drafted as a guide to help clarify the recommended replacement intervals for Rapco, Inc. new and overhauled pneumatic pumps. Compliance: Compliance with this service letter should be accomplished at the next 100 hour or annual inspection. Procedure:
1. Review the aircraft / engine maintenance logs and determine the part number of the pneumatic pump that is installed on the aircraft or engine, the total aircraft hours on the pump and date that the pump was installed.
2. Compare the information gathered in step 1 to table 1. 3. If the pneumatic pump exceeds either the “Hours in service” or “Time in Service” listed in
table 1, replace the pneumatic pump with a new FAA PMA approved Rapco, Inc. pneumatic pump.
4. If the pneumatic pump is under the “Hours in service” or “Time in Service” limits listed in table 1, the pneumatic pump may be returned to service until such time it has exceeded the “Hours in service” or “Time in Service” limits listed in table 1.
Service Letter
445 Cardinal Lane
Hartland, WI 53029 (262) 367-2292
www.rapcoinc.com
Table 1:
Pneumatic Pump Part Number / Series
Hours in service Time in Service
RA215CC Series (Not equipped with inspection port)
500 Hours time in service 6 years from date of installation
RA215CC Series (Equipped with inspection port)
Inspect in accordance with Rapco in service letter RASL-001, RASL-002 or RASL-006
6 years from date of installation
RA216CW (Not equipped with inspection port)
500 Hours time in service 6 years from date of installation
RA216CW (Equipped with inspection port)
Inspect in accordance with Rapco in service letter RASL-001, RASL-002 or RASL-006
6 years from date of installation
RA241CC Series (Equipped with inspection port)
Inspect in accordance with Rapco in service letter RASL-001, RASL-002 or RASL-006
6 years from date of installation
RA242CW Series (Equipped with inspection port)
Inspect in accordance with Rapco in service letter RASL-001, RASL-002 or RASL-006
6 years from date of installation
RA441CC Series (Not equipped with inspection port)
500 Hours time in service 6 years from date of installation
RA441CC Series (Equipped with inspection port)
Inspect in accordance with Rapco in service letter RASL-001, RASL-002 or RASL-006
6 years from date of installation
RA442CW Series (Not equipped with inspection port)
500 Hours time in service 6 years from date of installation
RA442CW Series (Equipped with inspection port)
Inspect in accordance with Rapco in service letter RASL-001, RASL-002 or RASL-006
6 years from date of installation
RAP441CC Series Inspect in accordance with Rapco in service letter RASL-001, RASL-002 or RASL-006
6 years from date of installation
RAP442CW Series Inspect in accordance with Rapco in service letter RASL-001, RASL-002 or RASL-006
6 years from date of installation
Any model pneumatic pump overhauled by Rapco, Inc.
500 Hours time in service 6 years from date of installation
Note:
Hours in Service listed in table 1 are representative of aircraft hours that the pneumatic pump has been in operation on the aircraft or engine. Time in service listed in table 1 is representative of calendar date that the pneumatic pump has been installed on the aircraft of engine