®
WELCOME Meet Shadow Fusion, unlike any other wireless headphones:
stunning,
lightweight and designed to sit naturally around your neck. Shadow
Fusion
adapts to your body and blends in with your style.
Shadow Fusion is powered by SOL REPUBLIC’s unique sound, a
long-lasting
battery that gives you a full day of music playback and easily
accessible audio
controls + mic to listen to music and take calls seamlessly.
Feel the music, not the headphones.
BIENVENUE Découvrez Shadow Fusion ! Rien à voir avec les autres
casques sans fil :
sensationnel, léger et conçu pour reposer naturellement autour de
votre cou.
Shadow Fusion s’adapte à votre morphologie et s’intègre
parfaitement à votre style.
Shadow Fusion s’appuie sur le son unique de SOL REPUBLIC, sur une
batterie
à grande autonomie qui vous offre une journée entière de musique et
sur
des contrôles et un microphone faciles d’accès vous permettant de
passer de
manière fluide de la musique à un appel téléphonique.
Ressentez la musique, pas les écouteurs.
4 EN EN 5
USB-C charging cable
1 Power button 2 MFB/Play/Pause 3 Forward track/volume up 4
Backward track/volume down
NOTE
For the best fit and sound, start with the largest size ear tip and
then work your way down.
CaseShadow Fusion earbuds
6 7
SETUP CHARGING EARBUDS
To charge the earbuds, open the charging port on the bottom of the
neckband on the left side. Plug the small end of the USB cable into
the charging port on the neckband and plug the large end of the USB
cable into a power source.
LED INDICATION
While charging, the large LED light will be red. A full charge will
take approximately 1 hour. When fully charged, the large LED light
will be blue.
PAIRING YOUR EARBUDS
STEP ONE To pair your earbuds, make sure the Bluetooth® setting on
your mobile device is turned on.
STEP TWO
Turn on your earbuds by pressing and holding the power button for 3
seconds. The power button is located on the bottom of the neckband
on the left side. The large LED will flash red and blue when
searching for a device. STEP THREE
Select “Shadow Fusion” from the Bluetooth® list on your mobile
device. Once the earbuds are connected, the large LED light will
pulse blue.
MULTI-POINT
Multi-point pairing allows you to connect two devices
simultaneously. Once paired, the Shadow Fusion can receive or make
calls from both devices.
To turn on multi-point, make sure your Shadow Fusion is connected
to a device and follow the below steps:
STEP ONE
To unpair your earbuds, press the round multi-function button on
top of the neckband on the left side for 5 seconds. You will hear a
voice prompt stating the earbuds are ready to pair.
STEP ONE
Make sure music is paused and phone calls are disconnected. Press
the multi-function button and volume down button once at the same
time. A voice will state that the earbuds are ready to pair.
STEP TWO
Connect the second device first following the steps under “Pairing
your Earbuds.”
STEP THREE
Once connected to the second device, you must re-pair the first
device. Now, both devices will be connected.
STEP FOUR
To turn off multi-point, simply press the multi-function button and
volume down button once at the same time.
Shadow Fusion
Shadow Fusion
NOTE
Press power button once when earbuds are turned on to check battery
level.
YOU WANT TO
Activate Siri Press and hold the multi-function button for 2
seconds
Activate Google Press and hold the multi-function button for 2
seconds
Pair the earbuds to a second device
Press the multi-function and volume down button at the same time
once
Turn off earbuds Press and hold the power button for 3
seconds
Check battery level of earbuds
Press the power button once when earbuds are powered on
Factory reset Press and hold the multi-function and volume up
button at the same time for three seconds
OTHER
BASICS
Pick up a call Press the multi-function button once
Decline a call Press and hold the multi-function button for 2
seconds
End a call Press the multi-function button once
Take a second incoming call
Press the multi-function button once
Decline a second incoming call
Use the phone keypad
Play or pause Press the multi-function button once.
Turn volume up Press the top line button (closest to your neck when
wearing)
Turn volume down Press the bottom line button (farthest from your
neck when wearing)
Next track Press and hold the volume up button for 2 seconds
Previous track Press and hold the volume down button for 2
seconds
BATTERY LEVEL
1 white LED Less than 40% power
10 EN EN 11
TROUBLESHOOTING
Having issues with your earbuds? Try working through the steps
below.
1. Make sure your earbuds are charged.
2. Turn off Bluetooth® on your device.
3. Press and hold power button on your earbuds for 3 seconds to
turn them off.
4. Wait a few seconds and then press and hold the power button on
your earbuds for 3 seconds to turn them back on.
5. Turn on Bluetooth® on your device.
6. Pair to “Shadow Fusion”.
FREQUENTLY ASKED QUESTIONS
1. How long will my Shadow Fusion earbuds take to fully
charge?
a. From 0%, your earbuds will take approximately 1 hour to fully
charge.
2. What should I do if my earbuds are not working?
a. Be sure the earbuds are fully charged. Then, complete a factory
reset. You can reset the earbuds by pressing and holding the
multi-function button and volume up button at the same time for 3
seconds. Then follow the instructions for pairing.
3. How long will the battery last?
a. The Shadow Fusion battery will last 10 hours, but this can vary
depending on volume levels and use.
4. What should I do if I have intermittent audio from the mic on my
earbuds?
a. Make sure nothing is covering the mic on the earbuds and make
sure you are not in a windy location. If this does not solve the
issue, try another phone call to make sure the issue is not
isolated to one call.
5. What happens if I do not pair my earbuds?
a. If the earbuds are powered on and not paired to a device, they
will go into standby mode and turn off after 3 minutes. To turn
them on again, press and hold the power button for 3 seconds.
CONTACT
Still have questions? We’ve got answers and we’re standing by. Give
us a shout, we’re here to help.
SUPPORT
The following is a set of resources to ensure you get the most out
of your SOL REPUBLIC product.
Web: SOLREPUBLIC.COM/SUPPORT
Twitter: @SOLREPUBLIC
Phone: +1.877.400.0310
Email:
[email protected]
QUÉ HAY ADENTRO
1 Botón de encendido 2 MFB/Reproducir/Pausa 3 Saltar a la siguiente
pista/subir
volumen
5 Micrófono 6 Puerto de carga 7 Luces LED
6 7
Cable de carga USB-C
NOTA
Para obtener el mejor ajuste y sonido, comience con la goma para
audífono más grande y vaya disminuyendo el tamaño hasta que ajuste
correctamente.
Estuche
14 ES ES 15
CONFIGURACIÓN CÓMO CARGAR SUS AUDÍFONOS Para cargar los audífonos,
abra el puerto de carga en la parte inferior de la banda para el
cuello del lado izquierdo. Conecte el extremo pequeño del cable USB
al puerto de carga en la banda para el cuello y conecte el extremo
grande del cable USB a la fuente de alimentación.
INDICACIÓN LED
Mientras se cargan, la luz LED grande se iluminará de color rojo.
Una carga completa tardará aproximadamente 1 hora. Cuando se
carguen completamente, la luz LED grande se iluminará de color
azul.
CÓMO ACOPLAR SUS AUDÍFONOS
PASO UNO Para acoplar sus audífonos, asegúrese de que la
configuración de Bluetooth® en su dispositivo móvil esté
habilitada. PASO DOS
Encienda sus audífonos presionando y sosteniendo el botón de
encendido durante 3 segundos. El botón de encendido está en la
parte inferior de la banda para el cuello del lado izquierdo. La
luz LED grande parpadeará de color rojo y azul cuando esté buscando
un dispositivo.
PASO TRES
Seleccione “Shadow Fusion” en la lista Bluetooth® de su dispositivo
móvil. Una vez que los audífonos estén conectados, la luz LED
grande parpadeará de color azul.
MULTIPUNTO
El emparejamiento multipunto le permite conectar dos dispositivos
simultáneamente. Una vez emparejado, el Shadow Fusion puede recibir
o hacer llamadas desde ambos dispositivos.
Para activar la función multipunto, cerciórese de que su Shadow
Fusion esté conectado a un dispositivo y siga los pasos a
continuación:
PASO UNO Para desacoplar sus audífonos, presione el botón redondo
multifunciones en la parte superior de la banda para el cuello del
lado izquierdo durante 5 segundos. Escuchará una voz diciendo que
los audífonos están listos para acoplarse.
PASO UNO
Asegúrese de que la música esté pausada y de que las llamadas
telefónicas estén desconectadas. Presione una vez el botón
multifunción y el botón bajar volumen simultáneamente. Una voz
indicará que los audífonos están listos para emparejarse.
PASO DOS Conecte el segundo dispositivo siguiendo los pasos
descritos en “Cómo emparejar sus audífonos”. PASO TRES Una vez que
esté conectado al segundo dispositivo, debe volver a emparejar el
primer dispositivo. Ahora, ambos dispositivos estarán
conectados.
PASO CUATRO
Para desactivar la función multipunto, simplemente presione una vez
el botón multifunción y el botón bajar volumen
simultáneamente.
Shadow Fusion
Shadow Fusion
NOTE
Presione una vez el botón de encendido cuando los audífonos estén
encendidos para revisar el nivel de la batería.
USTED DESEA
Revisar el nivel de la batería de los audífonos
Presione el botón de encendido una vez cuando los audífonos estén
encendidos
Activar Siri Oprima y mantenga presionado el botón multifunciones
durante 2 segundos
Activar Google Oprima y mantenga presionado el botón multifunciones
durante 2 segundos
Cambiar entre dos dispositivos
Presione los botones multifunciones y bajar volumen al mismo tiempo
una vez
Apagar los audífonos Oprima y mantenga presionado el botón de
encendido durante 3 segundos
Reinicio de fábrica Oprima y mantenga presionados los botones
multifunciones y subir volumen al mismo tiempo durante 3
segundos
OTRO
1 LED blanco Menos de 40 % de carga
FUNCIONES BÁSICAS
USTED DESEA
Rechazar una llamada Oprima y mantenga presionado el botón
multifunciones durante 2 segundos
Finalizar la llamada Presione el botón multifunciones una vez
Contestar una segunda llamada entrante
Presione el botón multifunciones una vez
Rechazar una segunda llamada entrante
Use el teclado del teléfono
MÚSICA
LLAMADAS
Reproducir o pausar Presione el botón multifunciones
Subir el volumen Presione el botón de hasta arriba (el que está más
cerca de su cuello cuando usa la banda)
Bajar el volumen Presione el botón de hasta abajo (el que está más
lejos de su cuello cuando usa la banda)
Pista siguiente Oprima y mantenga presionado el botón para subir el
volumen durante 2 segundos
Pista anterior Oprima y mantenga presionado el botón para bajar el
volumen durante 2 segundos
18 ES ES 19
mis audífonos?
a. Asegúrese de que nada esté cubriendo el micrófono en los
audífonos y que no está en un lugar con mucho viento. Si esto no
resuelve el problema, trate de realizar otra llamada telefónica
para asegurarse de que el problema no se relaciona únicamente con
una llamada.
5. ¿Qué sucede si no acoplo mis audífonos?
a. Si los audífonos se encienden y no se acoplan con un
dispositivo, se pondrán en modo de reposo y se apagarán después de
3 minutos. Para volver a encenderlos, oprima y mantenga presionado
el botón de encendido durante 3 segundos.
CONTACTO
¿Tiene más preguntas? Tenemos las respuestas y estamos esperando
atenderle. Llámenos, estamos aquí para ayudarle.
SOPORTE
Los siguientes son un conjunto de recursos para garantizar que
aproveche al máximo su producto SOL REPUBLIC.
En línea: SOLREPUBLIC.COM/SUPPORT
SOLUCIÓN DE PROBLEMAS
¿Tiene problemas con sus audífonos? Trate de seguir los siguientes
pasos.
1. Asegúrese de que sus audífonos estén cargados
2. Apague el Bluetooth® en su dispositivo
3. Oprima y mantenga presionado el botón de encendido en sus
audífonos durante 3 segundos para apagarlos
4. Espere unos cuantos segundos y después oprima y mantenga
presionado el botón de encendido en sus audífonos durante 3
segundos para volver a encenderlos.
5. Habilite el Bluetooth® en su dispositivo
6. Acoplar con “Shadow Fusion”
PREGUNTAS FRECUENTES
1. ¿Cuánto tardarán mis audífonos Shadow Fusion en cargarse
totalmente?
a. Desde 0 %, sus audífonos tardarán aproximadamente 1 hora en
cargarse totalmente.
2. ¿Qué debería hacer si mis audífonos no están funcionando?
a. Asegúrese de que sus audífonos estén completamente cargados.
Después, realice un reinicio de fábrica. Puede reiniciar los
audífonos al presionar al mismo tiempo los botones multifunción y
subir volumen, manteniendo presionados durante 3 segundos. Después
siga las instrucciones para el acoplamiento.
3. ¿Cuánto tiempo durará la batería?
a. La batería Shadow Fusion durará 10 horas, pero esto puede variar
dependiendo de los niveles de volumen y del uso.
4. ¿Qué debería hacer si tengo audio intermitente del micrófono
en
20 FR FR 21
du volume
5 Micro 6 Port de charge 7 Voyants à DEL
6 7
NOTE
Pour un confort et un son optimaux, commencez par l’embout
auriculaire le plus grand, puis passez au fur et à mesure à la
taille immédiatement inférieure si nécessaire.
Étui
22 FR FR 23
PRÉPARATION CHARGE DES ÉCOUTEURS
Para cargar los audífonos, abra el puerto de carga en la parte
inferior de la banda para el cuello del lado izquierdo. Conecte el
extremo pequeño del cable USB al puerto de carga en la banda para
el cuello y conecte el extremo grande del cable USB a la fuente de
alimentación.
LED INDICATION Le grand voyant à DEL s’allume en rouge pendant la
charge. Une charge complète prend environ 1 heure. Le grand voyant
à DEL s’allume en bleu lorsque la charge est terminée.
APPAIRAGE DES ÉCOUTEURS
Pour appairer les écouteurs, assurez-vous que la fonctionnalité
Bluetooth® est activée sur votre appareil mobile. ÉTAPE 2
Mettez les écouteurs en marche en appuyant sur le bouton
marche/arrêt pendant 3 secondes. Le bouton marche/ arrêt est situé
en bas du serre-nuque du côté gauche. Le grand voyant à DEL
clignote en rouge et en bleu pendant la recherche d’un
appareil.
ÉTAPE 3
Sélectionnez « Shadow Fusion » dans la liste Bluetooth® de votre
appareil mobile. Une fois que les écouteurs sont connectés, le
grand voyant à DEL clignote en bleu.
MULTIPOINT
DÉSAPPAIRAGE DES ÉCOUTEURS
L’appairage multipoint vous permet de connecter deux appareils
simultanément. Une fois l’appairage terminé, le Shadow Fusion peut
passer et recevoir des appels à partir des deux appareils.
Pour activer la fonction multipoint, assurez-vous que le Shadow
Fusion est connecté à un appareil et suivez les étapes
ci-dessous:
ÉTAPE 1
Pour désappairer les écouteurs, appuyez pendant 5 secondes sur le
bouton multifonction rond en haut du serre-nuque sur le côté
gauche. Un message vocal vous indiquera que les écouteurs sont
prêts pour l’appairage.
ÉTAPE 1
Assurez-vous que la musique est arrêtée et que les appels
téléphoniques sont déconnectés. Appuyez une fois simultanément sur
le bouton multifonction et sur le bouton de diminution du volume.
Un message sonore vous indique que les écouteurs sont prêts à être
appairés.
ÉTAPE 2
Connectez d’abord le deuxième appareil en suivant les étapes de la
section Appairage des écouteurs. ÉTAPE 3 Une fois le deuxième
appareil connecté, appairez de nouveau le premier appareil. Les
deux appareils sont maintenant connectés.
ÉTAPE 4
Para desactivar la función multipunto, simplemente presione una vez
el botón multifunción y el botón bajar volumen
simultáneamente.
Shadow Fusion
Shadow Fusion
NOTE
Appuyez une fois sur le bouton marche/arrêt lorsque les écouteurs
sont en marche pour consulter le niveau de charge de la
batterie
POUR
Vérifier le niveau de charge des écouteurs
Appuyez une fois sur le bouton marche/arrêt lorsque les écouteurs
sont en marche
Activer Siri Appuyez pendant 2 secondes sur le bouton
multifonction
Activer Google Appuyez pendant 2 secondes sur le bouton
multifonction
Basculer entre les deux appareils
Appuyez une fois sur le bouton multifonction et sur le bouton de
diminution du volume en même temps
Éteindre les écouteurs Appuyez pendant 3 secondes sur le bouton
marche/ arrêt
Réinitialisation Appuyez pendant 3 secondes sur le bouton
multifonction et sur le bouton d’augmentation du volume en même
temps
AUTRES FONCTIONS
4 voyants à DEL blancs Charge 81 %-100 %
3 voyants à DEL blancs Charge 61 %-80 %
2 voyants à DEL blancs Charge 40 %-60 %
1 voyant à DEL blanc Charge inférieure à 40 %
FONCTIONS DE BASE
Prendre un appel Appuyez sur le bouton multifonction
Refuser un appel Appuyez pendant 2 secondes sur le bouton
multifonction
Raccrocher Appuyez une fois sur le bouton multifonction
Répondre à un deuxième appel entrant
Appuyez une fois sur le bouton multifonction
Refuser un deuxième appel entrant
Utilisez le clavier du téléphone
MUSIQUE
APPELS
POUR
Lecture ou Pause Appuyez sur le bouton multifonction.
Augmenter le volume Appuyez sur le bouton du haut (le plus proche
du cou lorsque vous portez l’appareil)
Diminuer le volume Appuyez sur le bouton du bas (le plus éloigné du
cou lorsque vous portez l’appareil)
Piste suivante Appuyez pendant 2 secondes sur le bouton
d'augmentation du volume
Piste précédente Appuyez pendant 2 secondes sur le bouton de
diminution du volume
26 FR FR 27
a. Assurez-vous que le micro est bien dégagé et qu’il n’y a pas de
vent. Si cela ne résout pas le problème, passez un autre appel pour
confirmer que le problème ne concernait pas que l’appel en
question.
5. Que se passe-t-il si je n’appaire pas mes écouteurs?
a. Si les écouteurs sont en marche mais ne sont pas appairés à un
appareil, ils passent en mode de veille et s’éteignent au bout de 3
minutes. Pour les remettre en marche, appuyez pendant 3 secondes
sur le bouton marche/ arrêt.
CONTACTEZ-NOUS
Vous avez d’autres questions? Nous sommes là pour vous répondre.
Contactez-nous pour que nous puissions vous aider.
ASSISTANCE
Voici quelques ressources qui vous permettront de profiter au mieux
de votre produit SOL REPUBLIC.
Web: SOLREPUBLIC.COM/SUPPORT
Twitter: @SOLREPUBLIC
Téléphone: +1.877.400.0310
Email:
[email protected]
RÉSOLUTION DES PROBLÈMES
Vous avez des problèmes avec vos écouteurs? Essayez les étapes
ci-dessous.
1. Assurez-vous que vos écouteurs sont chargés.
2. Désactivez la fonctionnalité Bluetooth® sur votre
appareil.
3. Appuyez pendant 3 secondes sur le bouton marche/arrêt de vos
écouteurs pour les éteindre.
4. Attendez 3 secondes puis appuyez pendant quatre secondes sur le
bouton marche/arrêt des écouteurs pour les remettre en
marche.
5. Activez la fonctionnalité Bluetooth® sur votre appareil.
6. Faites l’appairage avec « Shadow Fusion »
FOIRE AUX QUESTIONS
1. Combien de temps faut-il pour charger complètement mes écouteurs
Shadow Fusion?
a. Lorsqu’ils sont complètement déchargés, les écouteurs prennent
environ une heure pour être complètement chargés.
2. Comment procéder si mes écouteurs ne fonctionnent pas?
a. Assurez-vous que les écouteurs sont complètement chargés.
Procédez ensuite à une réinitialisation. Pour réinitialiser les
écouteurs, appuyez simultanément pendant 3 secondes sur le bouton
multifonction et sur le bouton d’augmentation du volume. Suivez
ensuite les instructions d’appairage.
3. Combien de temps dure la batterie?
a. La batterie des écouteurs Shadow Fusion dure environ 10 heures,
mais la durée varie en fonction du niveau sonore et de
l’utilisation.
4. Que faire si l’audio du micro est intermittent sur mes
écouteurs?
28 DE DE 29
lauter
6 7
NOOT
Voor de beste pasvorm en geluid, begin met het grootste formaat
oorplug en werk dan naar beneden.
Behälter
30 DE DE 31
EINSTELLUNG LADEN IHRER OHRHÖRER Zum Laden Ihrer Ohrhörer den
Ladeanschluss unten am Halsbügel an der linken Seite öffnen, Das
kleine Ende des USB-Kabels in den Ladeanschluss am Halsbügel und
das große Ende des USB- Kabels in eine Stromquelle stecken.
LED INDICATION Während des Ladens leuchtet die große LED-Leuchte
rot auf. Eine volle Ladung nimmt ca. 1 Stunde in Anspruch. Nach
Abschließen des Ladevorgangs leuchtet die große LED blau auf.
PAIRING IHRER OHRHÖRER
STAP EEN Beim Pairing Ihrer Ohrhörer sicherstellen, dass an Ihrem
Mobilgerät Bluetooth® eingeschaltet ist.
STAP TWEE
Schalten Sie Ihre Ohrhörer ein, indem Sie die Ein/Aus-Taste 3
Sekunden lang drücken. Die Ein/Aus-Taste befindet sich unten am
Halsbügel an der linken Seite. Die große LED leuchtet abwechselnd
rot und blau, während nach einen Gerät gesucht wird. STAP
DREE
Shadow Fusion“ aus der Bluetooth®- Liste auf Ihrem Mobilgerät
wählen. Wenn die Ohrhörer verbunden sind, blinkt die große LED
schnell blau.
MEERPUNTS
ABTRENNEN IHRER OHRHÖRER
Met meerpunts koppelen kunt u twee apparaten tegelijkertijd
aansluiten. Eenmaal gekoppeld, kan de Shadow Fusion van beide
apparaten oproepen ontvangen of plaatsen.
Om meerpunts aan te zetten, zorg ervoor dat uw Shadow Fusion is
aangesloten op een apparaat en volg de onderstaande stappen:
STAP EEN Zum Abtrennen Ihrer Ohrhörer die runde Multifunktionstaste
oben am Halsbügel an der linken Seite 5 Sekunden lang drücken. Sie
hören eine Sprachansage, dass die Ohrhörer zum Pairing bereit
sind.
STAP EEN
Zorg ervoor dat de muziek is gepauzeerd en dat de
telefoongesprekken zijn verbroken. Druk tegelijkertijd één keer op
de multifunctionele knop 7en de knop Volume omlaag. Een stem geeft
aan dat de oordopjes klaar zijn om te koppelen.
STAP TWEE
Het tweede apparaat eerst aansluiten volgens de stappen onder “Uw
oordopjes koppelen.” STAP DREE Eenmaal aangesloten op het tweede
apparaat, moet u het eerste apparaat opnieuw koppelen. Nu zijn
beide apparaten aangesloten.
STAP VIER
Om meerpunts uit te schakelen, drukt u gewoon tegelijkertijd één
keer op de multifunctionele knop en de knop Volume omlaag.
Shadow Fusion
Shadow Fusion
NOTE
Die Ein/Aus-Taste einmal drücken, wenn die Ohrhörer eingeschaltet
sind, um den Batteriestand zu überprüfen.
SIE MÖCHTEN
Siri aktivieren Die Multifunktionstaste 2 Sekunden lang
drücken
Google aktivieren Die Multifunktionstaste 2 Sekunden lang
drücken
Zwischen zwei Geräten wechseln
Die Multifunktionstaste und die Taste zum Aufdrehen der Lautstärke
gleichzeitig drücken
Die Ohrhörer ausschalten Die Ein/Aus-Taste 3 Sekunden lang
drücken
Zurücksetzen auf Werkseinstellungen
Die Multifunktionstaste und die Taste zum Aufdrehen der Lautstärke
drei Sekunden lang gleichzeitig drücken
SONSTIGES
BATTERIESTAND
GRUNDFUNKTIONEN
Einen Anruf ablehnen Die Multifunktionstaste 2 Sekunden lang
drücken
Einen Anruf beenden Die Multifunktionstaste einmal drücken
Einen zweiten Anruf annehmen
Die Multifunktionstaste einmal drücken
Einen zweiten Anruf ablehnen
Wiedergabe oder Pause Die Multifunktionstaste drücken
Die Lautstärke aufdrehen Die obere Taste (die beim Tragen am
dichtesten an Ihrem Hals anliegt) drücken
Die Lautstärke runterdrehen
Die obere Taste (die beim Tragen am weitesten vom Ihrem Hals
entfernt ist) drücken
Nächster Titel Die Taste zum Aufdrehen der Lautstärke 2 Sekunden
lang drücken
Vorheriger Titel Die Taste zum Runterdrehen der Lautstärke 2
Sekunden lang drücken
34 DE DE 35
a. Stellen Sie sicher, dass das Mikro an den Ohrhörern nicht
verdeckt ist und dass Sie sich nicht an einem windigen Ort
befinden. Wenn dies das Problem nicht löst, versuchen Sie mit einem
anderen Anruf festzustellen, ob dies Problem nicht nur mit einem
Anruf auftrat.
5. Was passiert, wenn ich meine Ohrhörer nicht koppele?
a. Wenn die Ohrhörer eingeschaltet und nicht mit einem Gerät
gekoppelt sind, werden sie in den Bereitschaftsmodus versetzt und
schalten nach 3 Minuten ab. Schalten Sie Ohrhörer wieder ein und
drücken Sie die Ein/ Aus-Taste 3 Sekunden lang.
KONTAKTINFORMATIONEN
Haben Sie weitere Fragen? Wir sind bereit, um Ihre Fragen zu
beantworten. Kontaktieren Sie uns einfach und wir werden Ihnen
helfen!
UNTERSTÜTZUNG
Es folgen ein paar Ressourcen, um Ihnen zu helfen, das Beste aus
Ihren SOL REPUBLIC-Produkten herauszuholen.
Internet: SOLREPUBLIC.COM/SUPPORT
Twitter: @SOLREPUBLIC
Telefon: +1.877.400.0310
Email:
[email protected]
STÖRUNGSSUCHE
Probleme mit Ihren Ohrhörern? Versuchen Sie bitte, die folgenden
Schritte zu befolgen.
1. Stellen Sie sicher, dass Ihre Ohrhörer geladen sind
2. Schalten Sie Bluetooth® an Ihrem Gerät aus.
3. Drücken Sie die Ein/Aus-Taste an Ihren Ohrhörern 3 Sekunden
lang, um sie auszuschalten
4. Warten Sie ein paar Sekunden und drücken Sie dann die
Ein/Aus-Taste an Ihren Ohrhörern 3 Sekunden lang, um sie wieder
einzuschalten.
5. Schalten Sie Bluetooth® an Ihrem Gerät ein.
6. Koppeln mit „Shadow Fusion“
HÄUFIG GESTELLTE FRAGEN
1. Wie lange brauchen meine Shadow Fusion-Ohrhörer, um vollständig
aufgeladen zu werden?
a. Wenn Ihre Ohrhörer völlig entladen sind, brauchen Sie ca. 1
Stunden für eine vollständige Aufladung.
2. Was soll ich tun, wenn meine Ohrhörer nicht funktionieren?
a. Stellen Sie sicher, dass die Ohrhörer voll aufgeladen sind.
Führen Sie dann einen Werksreset durch. Sie können die Ohrhörer
zurücksetzen, indem Sie die Multifunktionstaste und die
Lauter-Taste 3 Sekunden lang gleichzeitig gedrückt halten. Folgen
Sie dann den Anweisungen für das Pairing.
3. Wie lange hält die Batterie?
a. Die Shadow Fusion-Batterie hält bis zu 10 Stunden je nach
Lautstärken und Einsatz des Geräts.
4. Was soll ich tun, wenn die Tonwiedergabe des Mikros an meinen
Ohrhörern unterbrochen wird?
36 IT IT 37
NOTA
Per ottenere la misura idonea e il suono migliore, iniziare dalla
misura di auricolare maggiore riducendola fino a trovare quella
adatta.
Scatola
3
4
1 Pulsante di alimentazione 2 MFB/Suona/Pausa 3 Track in avanti/
aumento volume
4 Track indietro/diminuzione volume
Auricolari Shadow Fusion
38 IT IT 39
MESSA A PUNTO CARICA DEGLI AURICOLARI Per caricare gli auricolari,
aprire la porta di carica sul fondo dell’archetto al lato sinistro.
Inserire il piccolo connettore del cavo USB nella porta di carica
sull’archetto e il grande connettore nella fonte di
alimentazione.
LED INDICATION Durante il periodo di carica, la grande spia
emetterà una luce rossa. Una carica completa durerà circa un’ora.
Al completamento della carica, la grande spia emetterà una luce
blu.
ACCOPPIAMENTO DEGLI AURICOLARI
PASSO PRIMO Per accoppiare gli auricolari, assicurarsi che
l’impostazione Bluetooth® sul dispositivo mobile sia
attivata.
PASSO SECONDO
Accendere gli auricolari premendo e tenendo premuto il pulsante di
alimentazione per 3 secondi. Il pulsante di alimentazione si trova
sul fondo dell’archetto al lato sinistro. La grande spia emetterà
una luce rossa lampeggiante quando si cerca un dispositivo.
PASSO TERZO Selezionare “Shadow Fusion” dall’elenco di Bluetooth®
sul dispositivo mobile. Una volta connessi gli auricolari, la
grande spia emetterà degli impulsi di luce blu.
MULTI-POINT
DISACCOPPIAMENTO DEGLI AURICOLARI
L’abbinamento multi-point permette di collegare due dispositivi
allo stesso tempo. Una volta abbinato, Shadow Fusion può ricevere
ed eseguire chiamate da entrambi i dispositivi.
Per attivare il multi-point verificare che Shadow Fusion sia
collegato a un dispositivo e seguire i passaggi indicati
oltre:
PASSO PRIMO
Per disaccoppiare gli auricolari, premere per 5 secondi il pulsante
multifunzioni rotondo sulla parte superiore dell’archetto al lato
sinistro.Una voce di prompt avviserà che gli auricolari sono pronti
per essere accoppiati.
PASSO PRIMO
Verificare che la musica sia in pausa e le chiamate via telefono
siano scollegate. Premere una volta simultaneamente il pulsante
multifunzione e quello di abbassamento volume. Una voce avviserà
quando gli auricolari sono pronti all’abbinamento. PASSO
SECONDO
Collegare il secondo dispositivo per primo, seguendo i passaggi
indicati in “Abbinamento degli auricolari”. PASSO TERZO
Una volta collegato al secondo dispositivo, occorre riabbinare il
primo dispositivo. Ora entrambi i dispositivi sono collegati.
PASSO QUARTO
Per spegnere il multi-point, basta premere una volta
simultaneamente il pulsante multifunzione e quello per abbassare il
volume.
Shadow Fusion
Shadow Fusion
NOTE
Per controllare il livello della batteria, premere una volta il
pulsante di alimentazione quando gli auricolari sono accesi.
SE SI DESIDERA
Controllare il livello della batteria sugli auricolari
Premere il pulsante di alimentazione una sola volta quando gli
auricolari sono accesi
Attivare Siri Premere il pulsante multifunzioni e tenerlo premuto
per 2 secondi
Attivare Google Premere il pulsante multifunzioni e tenerlo premuto
per 2 secondi
Scambiare tra due dispositivi
Premere una volta allo stesso tempo il pulsante multifunzioni e
quello del volume
Spegnere gli auricolari Premere il pulsante di alimentazione e
tenerlo premuto per 2 secondi
Impostazione di fabbrica Premere per tre secondi allo stesso tempo
il pulsante multifunzioni e quello del volume
ALTRO
1 luce bianca Alimentazione a meno del 40%
FUNZIONI DI BASE
SE SI DESIDERA
Accettare una chiamata Premere il pulsante multifunzioni
Rifiutare una chiamata Premere il pulsante multifunzioni e tenerlo
premuto per 2 secondi
Terminare una chiamata Premere una sola volta il pulsante
multifunzioni
Accettare una seconda chiamata in arrivo
Premere una sola volta il pulsante multifunzioni
Rifiutare una seconda chiamata in arrivo
Usare il tastierino del telefono
MUSICA
CHIAMATE
Suona o Pausa Premere il pulsante multifunzioni
Aumentare il volume Premere il pulsante superiore (il più vicino al
proprio collo quando si indossa)
Abbassare il volume Premere il pulsante inferiore (il più lontano
dal proprio collo quando si indossa)
Il brano seguente Premere il pulsante del volume e tenerlo premuto
per 2 secondi
Il brano precedente Premere il pulsante del volume e tenerlo
premuto per 2 secondi
42 IT IT 43
auricolari?
a. Assicurarsi che il microfono non sia coperto sugli auricolari e
che non si trovi in punto con molto vento. Se questo non risolve il
problema, tentare una nuova chiamata per assicurarsi che il
problema non sia limitato a una sola chiamata.
5. Che succede se non accoppia gli auricolari?
a. Se gli auricolari sono accesi e non accoppiati a un altro
dispositivo, essi vanno in modalità di standby e si spengono dopo 3
minuti. Per riaccenderli, premere il pulsante di alimentazione e
tenerlo premuto per 3 secondi.
CONTATTO
Ancora delle domande da fare? Abbiamo le risposte e restiamo in
attesa. Chiamateci, siamo qui per aiutarvi.
ASSISTENZA
Il seguente è un gruppo di risorse per assicurare che voi possiate
avere il massimo dal vostro prodotto SOL REPUBLIC.
Web: SOLREPUBLIC.COM/SUPPORT
Twitter: @SOLREPUBLIC
Telefono: +1.877.400.0310
Email:
[email protected]
Problemi con gli auricolari? Tentare di risolverli seguendo le
operazioni seguenti.
1. Assicurarsi che gli auricolari siano caricati
2. Spegnere Bluetooth® sul proprio dispositivo
3. Premere e tenere premuto per 2 secondi il pulsante di
alimentazione degli auricolari per spegnerli
4. Attendere qualche secondo e, quindi, premere e tenere premuto
per 3 secondi il pulsante di alimentazione degli auricolari per
riaccenderli.
5. Spegnere Bluetooth® sul proprio dispositivo
6. Accoppiarli a “Shadow Fusion”
DOMANDE PIÙ FREQUENTEMENTE FORMULATE
1. Quanto tempo è necessario per una carica completa degli
auricolari Shadow Fusion?
a. A partire da un livello dello 0% sarà necessaria circa 1 ora per
raggiungere la carica completa.
2. Che fare se gli auricolari non funzionano?
a. Verifica che gli auricolari siano completamente carichi, quindi
effettua un ripristino alle condizioni di fabbrica. È possibile
ripristinare gli auricolari tenendo premuti simultaneamente il
pulsante multifunzione e quello di aumento volume per 3 secondi.
Quindi segui le istruzioni di abbinamento.
3. Quanto tempo dura la batteria?
a. La batteria Shadow Fusion dura 10 ore, ma subordinatamente ai
livelli di volume e all’uso.
4. Che fare in caso di audio intermittente dal microfono
sugli
44 JP JP 45
セット内容
1 電源ボタン 2 MFB/再生/一時停止 3 次のトラック/ボリュームアップ 4 前のトラック/ボリュームダウン
Shadow Fusion イアバッド
6 7
LED INDICATION
充電中は大きい LED が赤く点灯し ます。 完全に充電されるまで約 1 時間です。フル充電になると LED
が青色になります。
イアバッドのペアリング
ステップ 1 イアバッドのペアリングを行うには、モバ イル機器側の Bluetooth® 設定がオン
になっていることを確認します。
ステップ 2 電源ボタンを 3 秒間長押ししてイアバ ッドをオンにします。 電源ボタンは、ネ ックバンド下側の左にあります。 大きい
LED が赤色と青色で交互に点灯し機 器を探します。
ステップ 3 モバイル機器の Bluetooth® 一覧で “Shadow Fusion” を選択します。 イ
アバッドが接続されると、大きい LED は 青色でパルス点滅します。
マルチポイント
イアバッドのペアリングの解除
マルチポイントをオンにするには、先ず Shadow Fusion に機器が接続されていることを確認し、
次に以下のステップに従います。
ステップ 1 イアバッドのペアリングを解除するには、 ネックバンド左側の丸いマルチファンクシ ョンボタンを 5 秒間長押しします。
イア バッドのペアリングの準備完了の音声メ ッセージが流れます。
ステップ 1 ミュージックはポーズ状態で電話は通 話中でないことを確認します。マルチフ ァンクション ボタンとボリュームダウン
ボタンを同時に押します。イアバッドの ペアリングの準備ができたことを告げ る音声メッセージが聞こえます。
ステップ 2 2 番目の機器を接続し、先ず「イアバッ ドのペアリング」の手順に従います。
ステップ 3 2 番目の機器が接続できたならば、 最初の機器のペアリングを再度行い ます。これで両方の機器が接続でき
ました。
ステップ 4 マルチポイントをオフにするには、マル チファンクション ボタンとボリュームダ ウン ボタンを同時に押します。
Shadow Fusion
Shadow Fusion
Siri を有効にする マルチファンクション ボタンを 2 秒間長押しする
Google を有効にする マルチファンクション ボタンを 2 秒間長押しする
2 つの機器を切り替える マルチファンクション ボタンとボリュームダウン ボ タンを同時に押す
イアバッドの電源をオフ にする 電源ボタンを 2 秒間長押しする
工場出荷時設定へのリ セット
その他
充電レベル
白色 LED が 1 個点灯 充電レベル 40%未満
基本的機能
次のことをするには
2 番目の通話を受ける マルチファンクション ボタンを 1 回押す
2 番目の通話を拒否する 電話のキーパッドを使用する
50 JP JP 51
5. イアバッドのペアリングを行わないとどうなりますか?
連絡先
ホームページ: SOLREPUBLIC.COM/SUPPORT
Twitter: @SOLREPUBLIC
TEL: +1.877.400.0310
メール:
[email protected]
4. 数秒間待ってから、イアバッドの電源ボタンを 3 秒間長押しして、再度 電源をオンにします。
5. 機器上で Bluetooth® をオンにします。
6. “Shadow Fusion” とのペアリングを選択します。
2. イアバッドが作動しない場合はどうしたらよいですか?
3. 電池はどれくらいもちますか?
4. イアバッドのマイクから音声が途切れる場合はどうしたらよいでしょう か?
a. イアバッドのマイクが何かに覆われていたり、風が強い場所でないこと
5352
Designed in San Francisco, CA. © 2019 SR Homedics, LLC. All rights
reserved. SOL REPUBLIC, the SOL REPUBLIC logo and SHADOW are
registered trademarks of SR HOMEDICS, LLC. Due
to continuous product improvements, the picture on the package may
differ slightly from the actual product. For Australia, the
included warranty complies with regulation 90 of the Competition
and Consumer Regulations 2010.
The Bluetooth® word mark and logos are registered trademarks owned
by Bluetooth SIG, Inc. and any use of such marks by SOL REPUBLIC is
under license.
Conçu à San Francisco, CA. © 2019 SR Homedics, LLC. Tous droits
réservés. SOL REPUBLIC le et logo SOL REPUBLIC, sont des marques de
commerce de SR Homedics, LLC. Images du produit peuvent varier
du
produit réel. Pour l’Australie, la garantie fournie est conforme à
la réglementation 90 de la concurrence et des
consommateursRèglement 2010. La marque Bluetooth® et les logos sont
des marques déposées appartenant à
Bluetooth SIG, Inc. et toute utilisation de ces marques par SOL
REPUBLIC est sous licence.
IB-SOLEP1200
©2014-2019 SR HOMEDICS, LLC.
AND SHADOW ARE REGISTERED
TRADEMARKS OF SR HOMEDICS, LLC.
THE BLUETOOTH® WORD MARK AND LOGOS ARE REGISTERED TRADEMARKS OWNED
BY BLUETOOTH
SIG, INC. AND ANY USE OF SUCH MARKS BY SOL REPUBLIC IS UNDER
LICENSE.
POUR JOINDRE LE SERVICE À LA CLIENTÈLE,
VEUILLEZ ENVOYER UN
©2014-2019 SR HOMEDICS, LLC. TOUS DROITS
RÉSERVÉS. SOL REPUBLIC ET
SR HOMEDICS, LLC.
BLE: 2.70DBM
인증받은자의상호: (주)디엠에이씨인터내 셔널 제품명/모델명:특정소출력무선기기(무선데 이타통신시스템용무선기기)/
SOL-EP1200