SECTION

Note:Uneven concrete walls shall be baggedwith Sika MonoTop Fairing Coat or otherappropriate cement based mortar

Granular freedraining backfill

Sika BlackSeal Protection Sheet or 50mm thick EPS fixed into positionwith tape

Minimum 2 coats of Sika BlackSeal Elastic appliedto primed substrate

Sika BlackSeal Elastic

Application to Concrete Walls

Scale 1:5

Detail no: SBE01 - Nov 2013

DRAWING MUST ALWAYS BE REVIEWED BY A DESIGN SPECIALIST AND IF NECESSARY MODIFIED TO ENSURE SUITABILITY FOR THE SPECIFIC APPLICATION

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) LtdPO Box 19192

Auckland 1746New Zealand.

Ph. 0800 745 269

www.sika.co.nz

Aug 2019Sika BlackSeal ElasticConcrete Walls - Wall to FloorScale 1:5Detail no: SBE02- Aug 2019

100 min.

Sika BlackSeal Protection Sheet or50mm thick EPS fixed into position with tape

Granular freedraining backfill Minimum 2 coats of

Sika BlackSeal Elastic appliedto primed substrate

200

n.t.s

.

100mm perforated drainage pipe wrapped ingeotextile filter fabric as per Engineer's design

Reinforced with Sika Deckweb Mesh

SikaSwell - P Profile 2010H

SikaProof A Tape - 150

DPM

SikaProof A Edge sheet

50mm site concrete100mm overlap, adhered to selvedge ofSikaProof A Edge sheet

Note:SikaProof A Edge sheet to top of footing,trim leg of SikaProof A Edge sheet to suit.

500100

150

100 min.

SECTION

150

min

.15

0 m

in.

100

min

.

Plaster or other selected finish

Ground level concrete protection

SECTION

Ove

rlap

Concrete Walls - Termination at

Ground Level

Sika BlackSeal Protection Sheet or 50mm thick EPS fixed into positionwith tape

Granular freedraining backfill

Sikalastic - 152 (Reinforced)

Sika BlackSeal Elastic

Sika BlackSeal Elastic appliedto primed substrate

Note:Uneven concrete walls shall be baggedwith Sika MonoTop Fairing Coat or otherappropriate cement based mortar

Scale 1:5

Detail no: SBE03 - Nov 2013

DRAWING MUST ALWAYS BE REVIEWED BY A DESIGN SPECIALIST AND IF NECESSARY MODIFIED TO ENSURE SUITABILITY FOR THE SPECIFIC APPLICATION

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) LtdPO Box 19192

Auckland 1746New Zealand.

Ph. 0800 745 269

www.sika.co.nz

Aug 2019Sika BlackSeal ElasticConcrete Walls - External CornerScale 1:5Detail no: SBE04- Aug 2019

Granular freedraining backfill

Sika BlackSeal Protection Sheet or50mm thick EPS fixed into position with tape

Sika BlackSeal Elastic appliedto primed substrate

200mm wide Sika Deckweb Meshbedded into Sika BlackSeal Elastic

External corner rounded offto minimum 6mm radius

125

125

DRAWING MUST ALWAYS BE REVIEWED BY A DESIGN SPECIALIST AND IF NECESSARY MODIFIED TO ENSURE SUITABILITY FOR THE SPECIFIC APPLICATION

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) LtdPO Box 19192

Auckland 1746New Zealand.

Ph. 0800 745 269

www.sika.co.nz

Aug 2019Sika BlackSeal ElasticConcrete Walls - Internal CornerScale 1:5Detail no: SBE05- Aug 2019

200mm wide Sika Deckweb Meshbedded into Sika BlackSeal Elastic

SECTION

Sika BlackSeal Protection Sheet or50mm thick EPS fixed into position with tape

Granular freedraining backfill

Sika BlackSeal Elastic appliedto primed substrate

Sand / Cement / BlackSeal Elastic mortar25mm angle fillet

125

125

10

0 m

in.

10

0 m

in.

250

Granular freedraining backfill

Sika BlackSeal Elastic appliedto primed substrate

200mm Wide Sika Deckweb Meshbedded into Sika BlackSeal Elastic

PLAN

SikaSwell - P Profile 2010H

Sika BlackSeal Protection Sheet or 50mm thick EPS fixed into positionwith tape

Sika BlackSeal Elastic

Scale 1:5

Concrete Walls - Construction Joint

Detail no: SBE06 - Nov 2013

Concrete Walls - Sealant Joint

Sika BlackSeal Elastic

Scale 1:5

Sika BlackSeal Protection Sheet or

50mm thick EPS fixed into position

with tape

Sikaflex AT-Facade on PEF rod

Sika BlackSeal Elastic applied

to primed substrate

Detail no: SBE07 - June 2016 Rev. A

PLAN

Granular free draining

backfill

Sikaflex Tank on PEF rod

Install Proprietary Isolation Tape

onto Sikaflex Tank prior to application

of Sika Blackseal Elastic

SikaGrout-212

100 min. 100 min. 302

Notes:1. Pipe penetration shall be made watertight prior to the application of Sika BlackSeal Elastic.2. SikaSwell S-2 requires a minimum 100mm concrete cover.3. Pipe shall be prepared by abrading and then solvent wiping prior to application of Sika BlackSeal Elastic.

Sika BlackSeal Protection Sheet or 50mm thick EPS fixed into positionwith tape

Concrete Walls - Cast in Pipe

Penetration

Fill any gaps between EPS and pipewith Sika Boom

Scale 1:5

SikaSwell S-2

10mm fillet of Sika BlackSeal - 1

Minimum 2 coats of Sika BlackSeal Elastic appliedto primed substrate taken 300mm onto pipe

Puddle flange

Sika BlackSeal Elastic

Granular freedraining backfill

200mm WideSika Deckweb Meshbedded into Sika BlackSeal Elastic

SECTION

Detail no: SBE08 - Nov 2013

DRAWING MUST ALWAYS BE REVIEWED BY A DESIGN SPECIALIST AND IF NECESSARY MODIFIED TO ENSURE SUITABILITY FOR THE SPECIFIC APPLICATION

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) LtdPO Box 19192

Auckland 1746New Zealand.

Ph. 0800 745 269

www.sika.co.nz

Aug 2019Sika BlackSeal ElasticConcrete Walls -Tie Bolt HoleScale 1:5Detail no: SBE09- Aug 2019

250

Sika BlackSeal Protection Sheet or50mm thick EPS fixed into position with tape

Granular freedraining backfill

200mm x 200mm square ofSika Deckweb Mesh bedded intofirst coat of Sika BlackSeal Elastic

Sika Grout-212 finishedFlush with surface

Minimum 2 coats ofSika BlackSeal Elastic appliedto primed substrate

PLAN

DRAWING MUST ALWAYS BE REVIEWED BY A DESIGN SPECIALIST AND IF NECESSARY MODIFIED TO ENSURE SUITABILITY FOR THE SPECIFIC APPLICATION

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) LtdPO Box 19192

Auckland 1746New Zealand.

Ph. 0800 745 269

www.sika.co.nz

Aug 2019Sika BlackSeal ElasticConcrete Walls -Boxed Out Pipe PenetrationScale 1:5Detail no: SBE10- Aug 2019

100 min. 100 min. 160 150

Sika Grout-212 finished flushwith surface

Minimum 2 coats of Sika BlackSeal Elastic applied toprimed substrate

Sika BlackSeal Elastic taken150mm on to wall and 150mm onto pipe

Fill any gaps between EPSand pipe with Sika Boom

150

150

SikaSwell-P Profile 2010H

10mm fillet of Sika BlackSeal - 1

50mm thick EPS or SikaProof ProtectionSheet fixed into position with tape

200mm wide Sika Deckweb Meshbedded into Sika BlackSeal ElasticSECTION

Note:1. Pipe penetration shall be watertight priorto the application of Sika BlackSeal Elastic.2. Pipe shall be prepared by abrading andthen solvent wiping prior to application ofSika BlackSeal Elastic.

Solid filled masonry block wall

SECTION

Minimum 2 coats of Sika BlackSeal Elastic appliedto primed substrate

Application to Masonry Walls

Scale 1:5

Note:Highly porous blocks and uneven masonry wallsshall be bagged with Sika MonoTop Fairing Coator other appropriate cement based mortar.

Sika BlackSeal Elastic

Granular freedraining backfill

Sika BlackSeal Protection Sheet or 50mm thick EPS fixed into positionwith tape

Mortar joints shall be tooled to compress the mortar amd made flush with Sika MonoTop Fairing Coat or other appropriate cement based mortar

Detail no: SBE11 - Nov 2013

15

0 m

in.

20

0 m

in.

500mm n.t.s.

SECTION

Sika BlackSeal Elasticapplied ontoSikaProof A Tape 150

50mm site concrete

100mm perforated drainage pipe wrapped in geotextile filter fabric

Sika BlackSeal Elastic

DPM

Sand / Cement / BlackSeal Elasticmortar 25mm angle fillet

SikaProof - A Edge sheet

Note:Highly porous blocks and uneven masonry wallsshall be bagged with Sika MonoTop Fairing Coator other appropriate cement based mortar.

Sika BlackSeal Protection Sheet or 50mm thick EPS fixed into positionwith tape

Minimum 2 coats ofSika BlackSeal Elastic appliedto primed substrate

Scale 1:5

Masonry Walls - Wall to Footing

Detail no: SBE12 - Nov 2013

DRAWING MUST ALWAYS BE REVIEWED BY A DESIGN SPECIALIST AND IF NECESSARY MODIFIED TO ENSURE SUITABILITY FOR THE SPECIFIC APPLICATION

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) LtdPO Box 19192

Auckland 1746New Zealand.

Ph. 0800 745 269

www.sika.co.nz

Aug 2019Sika BlackSeal ElasticMasonry Walls - Wall to FloorScale 1:5Detail no: SBE13- Aug 2019

Sika BlackSeal Protection Sheet or50mm thick EPS fixed into position with tape

Minimum 2 coats ofSika BlackSeal Elastic appliedto primed substrate

Note:Trim this leg of SikaProof AEdge sheet to suit

DPM

SikaProof A Edge sheet100 100mm overlap, adhered to selvedge of SikaProof A

Edge sheet

50mm site concrete100mm perforated drainage pipewrapped in geotextile filter fabric as per Engineer's designSECTION

Note:Highly porous blocks and uneven masonry wallsshall be bagged with Sika MonoTop Fairing Coator other appropriate cement based mortar.

Note:Wall must be flush with slab. If this is notachieved then any misalignment be made flush.

SikaProof A Tape 150

200mm wide SikaDeckweb Mesh

500 min.

500

100

min

.

150

min

.15

0 m

in.

Sika BlackSeal Elastic appliedto primed substrate

Plaster or other selected finish

Sika BlackSeal Protection Sheet or 50mm thick EPS fixed into positionwith tape

Granular freedraining backfill

Sikalastic 152 (Reinforced)

Ground level concrete protection

Ove

rlap

SECTION

Note:Highly porous blocks and uneven masonry wallsshall be bagged with Sika MonoTop Fairing Coator other appropriate cement based mortar.

Detail no: SBE14 - Nov 2013

Sika BlackSeal Elastic

Masonry Walls - Termination at

Ground Level

Scale 1:5

DRAWING MUST ALWAYS BE REVIEWED BY A DESIGN SPECIALIST AND IF NECESSARY MODIFIED TO ENSURE SUITABILITY FOR THE SPECIFIC APPLICATION

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) LtdPO Box 19192

Auckland 1746New Zealand.

Ph. 0800 745 269

www.sika.co.nz

Aug 2019Sika BlackSeal ElasticMasonry Walls- Esternal CornerScale 1:5Detail no: SBE15 Aug 2019

External corner rounded off to

minimum 6mm radius

200mm Wide Sika Deckweb Mesh

bedded into Sika BlackSeal Elastic

Minimum 2 coats of

Sika BlackSeal Elastic applied to

primed substrate

Sika BlackSeal Protection Sheet or

50mm thick EPS fixed into position

with tape

Note:

Highly porous blocks and uneven masonry walls shall

be bagged with Sika MonoTop Fairing Coat or other

appropriate cement based mortar

125

125

DRAWING MUST ALWAYS BE REVIEWED BY A DESIGN SPECIALIST AND IF NECESSARY MODIFIED TO ENSURE SUITABILITY FOR THE SPECIFIC APPLICATION

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) LtdPO Box 19192

Auckland 1746New Zealand.

Ph. 0800 745 269

www.sika.co.nz

Aug 2019Sika BlackSeal ElasticMasonry Walls- Internal CornerScale 1:5Detail no: SBE16 Aug 2019

50mm thick EPS fixed into position

with tape or Sika BlackSeal Protection Sheet

Minimum 2 coats of

Sika BlackSeal Elastic applied

to a primed substrate

200mm wide Sika Deckweb Mesh

bedded into Sika BlackSeal Elastic

Sand / Cement / Sika BlackSeal Elastic

mortar 25mm angle fillet

Note:

Highly porous blocks and uneven masonry walls shall be

bagged with Sika MonoTop Fairing Coat or other

appropriate cement based mortar

DRAWING MUST ALWAYS BE REVIEWED BY A DESIGN SPECIALIST AND IF NECESSARY MODIFIED TO ENSURE SUITABILITY FOR THE SPECIFIC APPLICATION

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) LtdPO Box 19192

Auckland 1746New Zealand.

Ph. 0800 745 269

www.sika.co.nz

Aug 2019Sika BlackSeal ElasticMasonry Walls-Sealant JointScale 1:5Detail no: SBE17- Aug 2019

SikaGrout-212

PLAN

Sikaflex AT-Facade on Sika PEF rod

Minimum 2 coats ofSika BlackSeal Elastic appliedto primed substrate

Sika BlackSeal Protection Sheet or50mm thick EPS fixed into positionwith tapeInstall Proprietary Isolation Tape

on to Sikaflex Tank prior to applicationof Sika Blackseal Elastic

Sikaflex Tank on PEF rod

Granular freedraining backfill

Square edges flushwith the joint

DRAWING MUST ALWAYS BE REVIEWED BY A DESIGN SPECIALIST AND IF NECESSARY MODIFIED TO ENSURE SUITABILITY FOR THE SPECIFIC APPLICATION

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) LtdPO Box 19192

Auckland 1746New Zealand.

Ph. 0800 745 269

www.sika.co.nz

Aug 2019Sika BlackSeal ElasticMasonry Walls - Pipe PenetrationScale 1:5Detail no: SBE18-A- Aug 2019

Minimum 2 coats of

Sika BlackSeal Elastic applied

to primed substrate

Sikaflex Tank on PEF rod

Sika BlackSeal Elastic taken

150mm onto wall and 150mm

on to pipe

Sika BlackSeal Protection Sheet or

50mm thick EPS fixed into position

with tape

Sikaflex AT - Facade

on PEF rod

Note:

Highly porous blocks and uneven

masonry walls shall be bagged with

Sika MonoTop Fairing Coat or other

appropriate cement based mortar.

Fill any gaps between EPS and pipe

with Sika Boom

SECTION

Isolation Tape

10mm fillet of Sika BlackSeal - 1

150 150

200mm wide Sika

Deckweb Mesh bedded

into Sika BlackSeal

Elastic

DRAWING MUST ALWAYS BE REVIEWED BY A DESIGN SPECIALIST AND IF NECESSARY MODIFIED TO ENSURE SUITABILITY FOR THE SPECIFIC APPLICATION

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) LtdPO Box 19192

Auckland 1746New Zealand.

Ph. 0800 745 269

www.sika.co.nz

Aug 2019Sika BlackSeal ElasticPrecast Walls - Wall to FloorScale 1:5Detail no: SBE19 Aug 2019

Precast concrete panel

Sikaflex Tank

to horizontal joint

SikaProof A Tape 150

Sika BlackSeal Protection Sheet or

50mm thick EPS fixed into position

with tape

Minimum 2 coats of

Sika BlackSeal Elastic applied

to primed substrate

Panel shim

Sika Grout-212

DPM

SikaProof A Edge sheet

100mm overlap, adhered to selvedge of

SikaProof A Edge sheet

50mm site concrete

100mm perforated drainage pipe wrapped

in geotextile filter fabric

Granular free

draining backfill

SECTION

100

500

500 n.t.s.200

min

.

Install Proprietary Isolation Tapeon to Sikaflex Tank prior to applicationof Sika Blackseal Elastic

DRAWING MUST ALWAYS BE REVIEWED BY A DESIGN SPECIALIST AND IF NECESSARY MODIFIED TO ENSURE SUITABILITY FOR THE SPECIFIC APPLICATION

The information contained herein and any other advice are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika's recommendations. The information onlyapplies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika'sTechnical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer tothe most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Sika (NZ) LtdPO Box 19192

Auckland 1746New Zealand.

Ph. 0800 745 269

www.sika.co.nz

Aug 2019Sika BlackSeal ElasticPrecast Walls on Continuous FootingScale 1:5Detail no: SBE20-A- Aug 2019

DPM

Precast concrete panel

Granular free

draining backfill

Sika BlackSeal Protection Sheet or

50mm thick EPS fixed into position

with tape

Minimum 2 coats of

Sika BlackSeal Elastic applied

to primed substrate

100mm perforated

drainage pipe wrapped

in geotextile filter fabric

to Engineer's design

Sika Grout-212

100mm overlap, adhered to

selvedge of

SikaProof A Edge sheet

SikaSwell - P Profile 2010H

SECTION

100 min.

150

Isolation Tape

Sikaflex Tank on PEF rod

SikaProof A Tape 150

100m

m10

0mm