Sika Pre-Treatment ChartFor Sikafloor® Marine Applications

Sikafloor® Marine Technology

Version 1 (05/2012)

Sika Services AGBusiness Unit IndustryTuffenwies 16CH-8048 ZurichSwitzerlandPhone +41 (0) 58 436 40 40Fax +41 (0) 58 436 45 64E-Mail industry@ch.sika.com

Please consult the most current local Product Data Sheet prior to any use.

www.sika.com

Legal NoteThe information contained herein and any other advice are given in good faith based on Sika‘s current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sika‘s recommendations. The information only applies to the application(s) and product(s) expressly referred to herein and is based on laboratory tests which do not replace practical tests. In case of changes in the parameters of the application, such as changes in substrates etc., or in case of a different application, consult Sika‘s Technical Service prior to using Sika products. The information contained herein does not relieve the user of the products from testing them for the intended application and purpose. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which can be downloaded on your local sika company website or will be supplied on request.

Abbreviation Product/Explanation

No special pre-treatment required

B C / V Broom Cleaning or Vacuum Cleaning

P C Sikafloor® Marine Primer-C

GR Grinding (40 grit)

ZP SikaCor® ZP-Primer

n.a. Not applicable

Utilisation of Sika Pre-Treatment ChartInformation about the pre-treatment of surfaces in this document serves as a guideline only and must be verified by tests on original substrates. Project specific pre-treatment recommendations, based on laboratory tests, are available from Sika on request.

Recommendations for Sikafloor® Marine Range

Application Temperature: 5 – 35°C, (40 – 95°F)1 If the deck is contaminated with oil, grease or similar use Sika Remover®-208 prior to Sikafloor® Marine Primer C / Sikafloor® Marine PU-Red 2 Remove any loose rust prior to use of Sikafloor® Marine Primer C / Sikafleoor® Marine PU-Red 3 Please contact local Technical Departement of Sika Industry

Products

Substrates

Sikafloor® Marine PU-Red(Visco elastic)

Self-levelling mortar: Sikafloor® Marine 100Sikafloor® Marine 120

Trowel out levelling mortar:Sikafloor® Marine KG-202 NSikafloor® Marine KG-404 N

Sikafloor® Marine Litosilo N(Trowel out levelling mortar)

Sikafloor® Marine 18(Trowel out levelling mortar)

Sikafloor® Marine Thermo-light(2 layer level-ling system)

Sikafloor® Marine Elastic(Water proofing mortar)

Sikafloor® Marine E-43(Epoxy floor)

Steel Deck B C / V B C / V P C B C / Vbefore Rockwool

B C / V P C B C / V P C n.a.B C / V

Aluminium Deck GR B C / V ZP

GR B C / V ZP P C

B C / Vbefore Rockwool

GR B C / V ZP P C

GR B C / V ZP P C

n.a.GR B C / V ZP

Steel Deck with zinc Primer

GR B C / V ZP

GR B C / V ZP P C

B C / Vbefore Rockwool

GR B C / V ZP P C

GR B C / V ZP P C

n.a.GR B C / V ZP

Sikafloor® Marine 18 Sikafloor® Marine KG-202 NSikafloor® Marine KG-404 N

n.a.GR B C / V P C

B C / Vbefore Rockwool

GR B C / V P C

GR B C / V P C

GR B C / V GR B C / V

Sikafloor® Marine Litosilo N

n.a.GR B C / V P C

GR B C / V P C

GR B C / V P C

GR B C / V P C

GR B C / V GR B C / V

PU-Red n.a. B C / V n.a. n.a. n.a.

SikaCor® ZP-Primer Sikafloor® Marine Primer-C Sika® Remover-208

Colour Component A: grey or red

Component B:pale yellow

White Transparent

Type of product Primer Remover

Application temperature 10 – 35°C (50 – 95°F) 5 – 35°C (40 – 95°F) 5 – 40°C (40 – 105°F)

Application Brush, roller Roller Wipe-on, wipe-off with lint-free paper towel

Material consumption on: – steel– mortar layers

200 g/m2 approx. by brush or rollerNo use of SikaCor® ZP-Primer on this substrate

75 g/m2 approx.150 – 300 g/m2 approx.

depending on contaminationn. a.

Flash-off time 10°C (50°F): 5 h (maximum 14 h)30°C (86°F): 2 h (maximum 14 h)20°C (68°F): 3 h (maximum 14 h)

2 h to 3 h 30 min. (max. 24 h)

Notice: Sika® Remover and Primers are moisture reactive systems. In order to maintain product quality it is important to reseal the container immediately after use. With frequent use i.e. opening and closing several times, we recommend to dispose of the product one month after opening. With infrequent use, we recommend to dispose of the product 2 months after opening.

1

1

1

2

2

1

3