Simon XT with Plug & Protect™Quick Start Guide

For the most current resources, video and live chat during office hours: www.livewatchsecurity.com/login

Thanks for choosing Plug & Protect™ from SafeMart. This product is designed to be quickly placed in your home or office while offering comprehensive protection. Your home will be fully protected in just a few minutes. This guide is designed to aid you in the placement of your sensors and master control unit. Please read this guide in its entirety before placing your sensors. This system has been programmed to your specifications and sensor placement labels have been applied to each sensor. It is important not to separate the labeled boxes from the sensors until you are ready to place the devices in the locations stated on the label.

If you have ordered a Wireless Communicator with your system, be sureto follow along with the video sent to your email address.

Disclaimer – Important Information, Please read

Copyright: © 2002-2012 SafeMart, LiveWatch Security LLC St. Mary’s KS 66536. All Rights Reserved.

Trademarks and patents: SafeMart and LiveWatch logos, are registered trademarks of LiveWatch Security LLC. Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.

Warning: The unauthorized reproduction or distribution of this copyright work is illegal. Criminal copyright infringement, including infringement without monetary gain, is investigated by the FBI and is punishable by up to 5 years in federal prison and a fine of $250,000.

Disclaimer: The information in this document is subject to change without notice. LiveWatch Security LLC (“LiveWatch Security”) d/b/a SafeMart assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or indirectly, of the use or application of any of the contents of this document. For the latest documentation, log in at LiveWatchSecurity.com/Login.

This publication may contain examples of screen captures and reports used in daily operations. Examples may include fictitious names of individuals and companies. Any similarity to names and address of actual businesses or persons is entirely coincidental.

Safety Information: Before you install your products, please read the appropriate information, notices and other material, including the safety and site preparation section in your product documentation. For your safety, please consult a professional if you have any questions. There are certain components that connect to high voltage electrical outlets. Improper installation or workmanship by you (the installer) can lead to severe injury, property damage, system malfunction or death.

This guide is provided as information about low voltage products. Since every low-voltage project is unique, any information contained herein WILL NOT constitute an endorsement of the suitability of any equipment or application. Use this product only for the purpose it was designed. For the latest documentation, contact LiveWatch Security d.b.a. SafeMart log in at LiveWatchSecurity.com/Login

Simon XT Door & Window Sensors

Keychain Remote Motion Detector

Identify the Components in the Box

For the most current resources, video and live chat during office hours: www.livewatchsecurity.com/login

AfterBefore

1. Before plugging your panel into the wall, connect the red wires in the back of your master control unit. This connects your backup battery. Make sure the wires are snug.

2. Your system should be powered up and the display should be active.

1. The location of your master control unit should be:• Near a power outlet within reach of the unit’s power cord.• Away from windows–the display cannot be legible from outside.• On a surface that is easily accessible to you.• Away from wireless routers or wireless telephones.• In an area with cellular service (see next step).

2. Test the strength of your cellular signal by pressing and holding the number 5 on your keypad for 5 to 10 seconds. The display will indicate signal strength by showing boxes. 5 boxes indicates strong signal strength and 0 indicates no signal at all. We recommend a location with at least 3 boxes. See figure 3 below.

After the wires are connected, your system will beep until you complete the next step. To silence these beeps, press STATUS, then DISARM

The radio bars above indicate that the home security system has 3 of 5 boxes–standard signal strength.

1a: Connect Your Backup Battery

1b: Find a Location For Your Master Control Unit

3. Plug your master control unit into the wall outlet.

For the most current resources, video and live chat during office hours: www.livewatchsecurity.com/login

AfterBefore

1. Select a location on the door or window. The larger part of the contact should be on the non-movable part of the door/window frame - see diagram.

2. After peeling off the wax paper backing on the tape, mount the two contacts by applying pressure to the door/window. When you mount:

• Place the sensors at a maximum of ½” apart – closer is better.• Do not exceed the width of a pencil between the sensors.• The small arrows on the components need to be aligned and

facing each other on the inside of the mount.

1. Remove the double sided backing from the tape on the back of the sensor.

2. We recommend mounting these sensors in the corners of the rooms you are protecting. Do not place the motions towards a window facing the outside; place them facing in, towards the inside of your home; in an area where a burglar may pass. Once the tape is peeled place the sensor about 7 or 8 feet high in the corner. Press the motion sensor hard into place. Once the adhesive is secure, you have completed the installation.

If your doors or windows do not allow you to properly place the large part of the sensor on the frame, it is okay to place the smaller portion on the door or window frame to make the placing work more easily. This is an acceptable method of sensor placement although it should only be used when necessary.

2a: Place the Door and Window Sensors

2b: Place the Motion Sensors

For the most current resources, video and live chat during office hours: www.livewatchsecurity.com/login

There are 2 “arming modes”: Stay Mode and Away Mode.1. Stay Mode arms the perimeter (windows and exterior doors for

example) and is usually used while you are home. 2. Away Mode arms the perimeter as well as the interior sensors

(motion sensors for example) and is usually used while you are away from the phone.

Arm your system1. Master Control Unit

1. Press “Doors + Windows” to arm the system using Stay Mode2. Press “Doors + Windows” and “Motions” to arm the system

using Away Mode2. Keychain Remote

1. Press “Arm” key once for Stay Mode2. Press “Arm” key twice for Away Mode

3. Alarm.com App or Website1. Click “Arm (Away)” for Away Mode2. Click “Arm (Stay)” for Stay Mode

Disarm your system1. Master Control Unit

1. Press the “Disarm” key on the Master Control Unit followed by your user code. (Your user code was created in the LiveWatch Customer Center and was sent to you in a confirmation email)

2. Enter your user code into the master control unit2. Keychain Remote

1. Press the “Disarm” key on your keychain for 2 seconds3. Alarm.com App or Website

1. Click “Disarm”

When arming and disarming your system, the master control unit will beep to indicate that you have a given amount of time to either exit when leaving or enter your code when entering. This is known as Entry/Exit Delay. When the armed master control unit begins the count down by beeping, the beeps that it gives off will cease once the system is armed. Your system will not beep the entire time you are gone, only the time that is set under Entry/Exit Delays; commonly 30 or 60 seconds.

Keychain RemoteMaster Control Alarm.com App

3: Arm and Disarm Your System

For the most current resources, video and live chat during office hours: www.livewatchsecurity.com/login

• Before you are ready to activate your system, log into your LiveWatch Customer Account and make sure that you have completed Steps 1-4 in your Customer Dashboard.

• A SafeMart support technician will call you on the date and time of your scheduled appointment to test and activate the system. Please be at the location of the system.

• If you are unable to make your scheduled appointment, please visit www.livewatchsecurity.com/login to reschedule.

After your system is tested and activated you will receive:• Your account number (eg: ABC7890)• The phone number for our 24/7 Central Station

You can customize your system using the Alarm.com App and website. The SafeMart technician will provide you with a login and password during your activation appointment.

4: Activate and Test Your System

For the most current resources, video and live chat during office hours: www.livewatchsecurity.com/login

©2012  LiveWatch  Security  d.b.a.  SafeMart,  All  Rights  Reserved

The fastest answers 24/7 can be found at: www.livewatchsecurity.com/login

Mobile Apps• iPhone: Download the free Alarm.com App for your iPhone or iPod

touch (iOS 3.2 or later required). Search for "Alarm.com" in the App Store.

• iPad: Download the free Alarm.com App for your iPad (iOS 3.2 or later required). Search for "Alarm.com" in the App Store.

• BlackBerry: Download the free Alarm.com App for BlackBerry by visiting www.alarm.com/bbinstall from the web browser of your compatible BlackBerry device. (Requires OS 4.2.1 or later. Compatible with the BlackBerry Curve, Pearl, Bold, and 8800 series devices.)

• Android: To download the free Alarm.com App for Android (compatible with Android OS 1.6 or later), visit the Android Market from your device and search for "Alarm.com".

• Mobile Site: Have web access on your cell phone? Just open its web browser and go to the Mobile Site URL (m.alarm.com) to log into your account. The Mobile Site includes many features of the primary website and is specially formatted to fit your mobile screen.

Monitor and control your system from the road with these free tools for mobile devices.

On the Go?

For the most current resources, video and live chat during office hours: www.livewatchsecurity.com/login

Thank  you  for  choosing  SafeMart  and  LiveWatch  Security.

For the most current resources, video and live chat during office hours: www.livewatchsecurity.com/login