Site Top DIP Switch

7/31/2019 Site Top DIP Switch

1/5

Both for the V3 and V2 site, the ID_DOG have 15 bits in logical. There are

two switches S1 and S2 physically.

For each bit of S1 and S2, status ON means 0, OFF means 1

S1 bits 18 are mapped ID_DOG logical bits 07; S2 bit 18 are mapped

ID_DOG logical bits 815;

V3

F I G U R E 1 - CA B I N E T -TO P DIP S W I T C H E S

14 13 345678910111215 012

B TS_TY PE BTS_N OSLAVE1_

PORT

SLAVE2_

PORTSATE ABIS_PORT ABIS_TS

The meaning of each bit is explained as follows:

NO Name Meaning Description

15 BTS_TYPE BTS TYPE 1100: B8018

14 1101: B811213 1110: M8202

12 1111: M8204

11 BTS_NO No. of the cabinet of the samesite

00: Basic cabinet

01: Extended cabinet

10: Extended cabinet10

9 SLAVE1_PORT The E1 port of the basic cabinetto connect extended cabinet 1

00: Port E of the basic cabinet

01: Port F of the basic cabinet

10: Port G of the basic cabinet

11: Port H of the basic cabinet

8




10: Port G of the basic cabinet

11: Port H of the basic cabinet

6

5 SATE Whether to use the satellite Abislink or not

0: Common Abis

1: Satellite Abis

4 ABIS_PORT O&M port number 00: Port A 01: Port B

10: Port C 11: Port D3

2 ABIS_TS The O&M LAPD timeslot on theAbis interface

000: TS16 001: TS31 010: TS30

011: TS29 100: TS28 101: TS27

110: TS26 111: TS25

1

0

The number of the E1 port of the basic cabinet to connect the lower-level site cannot be

the same as of SLAVE_PORT1 or SLAVE_PORT2. For example, suppose Port F of

the basic cabinet connects with the lower-level site, then the values of SLAVE_PORT1


2/5

and SLAVE_PORT2 cannot be 01.

For example,site1 and site2 are BTS B8018,site2 is the downsite of site1.Both sites use

the common Abis,site1 E1 port A connect to BSC,site2 E1 port A connect to site1 port

D. The O&M timeslot of site2 is TS31.Then the dip switches areSite1: S1(18) 00000000 S2(18) 00000011

Site2: S1(18) 10000000 S2(18) 00000011

V2

15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

INDOOR SYN CHANEL_NO BTS_NO SLAVE1_PO RT SLAVE2_P ORT SATE ABIS_PORT ABIS_TS

The meaning of each bit is explained as follows:

NO Name Meaning Description

15 INDOOR BTS TYPE 0: Indoor 1:Outdoor

14 SYN Network syn_clock source 0: Get from E1 1: SDH syn_clock 13 CHANNEL_NO Port of the monitor 00:RS232 for transparent channel

01:RS422 for transparent channel

10:RS232 for SMC

12

11 BTS_NO No. of the cabinet of the samesite

00: Basic cabinet

01: Extended cabinet

10: Extended cabinet10


00: Port C of the basic cabinet

01: Port D of the basic cabinet



8


00: Port C of the basic cabinet

01: Port D of the basic cabinet



6

5 SATE Whether to use the satellite Abislink or not

0: Common Abis

1: Satellite Abis

4 ABIS_PORT O&M port number 00: Port A 01: Port B

10: Port C 11: Port D3

2 ABIS_TS The O&M LAPD timeslot on theAbis interface

000: TS16 001: TS31 010: TS30

011: TS29 100: TS28 101: TS27

110: TS26 111: TS25

1

0

The number of the E1 port of the basic cabinet to connect the lower-level site cannot be

the same as of SLAVE_PORT1 or SLAVE_PORT2. For example, suppose Port D of

the basic cabinet connects with the lower-level site, then the values of SLAVE_PORT1

and SLAVE_PORT2 cannot be 01.


3/5

For example,site1 and site2 are BTSV2,site2 is the downsite of site1.Both sites use the

common Abis, site1 E1 port A connect to BSC,site2 E1 port A connect to site1 port

D.The O&M timeslot of site2 is TS31.Then the dip switches are

Site1: S1(18) 00000000 S2(18) 00000000

Site2: S1(18) 10000000 S2(18) 00000000

Note

To check the DIP switch status in site by signal trace

Site Power On Report (157)- last 4 they are in HEX change to BINARY this is for ibsc

For V2 leaving last 2 next 4 (Reset site and find this message in signal tracing(OAM))


4/5

DIP Configuration for Micro BTS(M8202)

S1 S2 S3

Figure 1: For Common Abis (Abis TS 16)

S1 S2

S3

Figure 2: For Satellite Abis (Abis TS 25)

1

OFF

2

OFF

3

ON

4

OFF

1

ON

2

ON

3

ON

4

ON

5

ON

6

OFF7

OFF

8

OFF

1

OFF

2

OFF

3

ON

4

OFF


5/5

Documents

Site Top DIP Switch