Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-1
350 Series Casement
Size and Performance Summary
Glazing Performance
Grille Profiles and Patterns
Size Tables
Design Data
Detailed Product Description
Cross Sections
The information published in this document is believed to be accurate at the time of publication. However, because we are constantly working to improve our products, specifications are
subject to change without notice. Consult your local Pella representative for up-to-date product information.
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-2
350 Series Casement
S = Standard; O = Optional
(1) Published performance data is for single unit only. See Design Data pages in this section for specific product performance class and grade values.
(2) The higher the level, the greater the product's ability to resist forced entry.
(3) ASTM E 1425 defines standard sizes for acoustical testing. Ratings achieved at that size are representative of all sizes of the same configuration.
The presence of low-e or argon have negligible effect on sound attenuation characteristics.
Sizes
Standard Sizes S
Special Sizes Available Built on 1/8" Increments O
Frames
Nail Fin Only O
Nail Fin with J-Channel O
4-1/2" Block S
3-1/4" Block Pocket Install/Replacement S
Double-Wall Flush Flange O
Integral 5/8" Flange O
Performance 1
Standard Performance
Meets or Exceeds AAMA/WDMA RatingsLC-PG40
Hallmark Certified
Air Infiltration (cfm / ft2 of frame @ 1.57 psf wind pressure.) 0.05
Design Pressure 40 psf
Water Penetration Resistance 6.06 psf
Performance Upgrade
Meets or Exceeds AAMA/WDMA RatingsLC-PG60
Hallmark Certified
Air Infiltration (cfm / ft2 of frame @ 1.57 psf wind pressure.) 0.05
Design Pressure 60 psf
Water Penetration Resistance 9.20 psf
Other Performance Criteria
Forced Entry Resistance (Minimum Security Grade) 2 40
Maximum Operating Force (lbs) (Initiate Motion / Maintain Motion) 15/6
Size and Performance Data
Sound Transmission Class / Outdoor-Indoor Transmission Class
Frame Size Tested 3
Glazing SystemSTC
RatingOITC
RatingOverall Glazing Thickness
Exterior Glass Thickness
Interior Glass Thickness
Third Pane Thickness
Casement - Dual-Pane Insulating Glass
24" x 60" 11/16" 3mm 3mm — 30 24
24" x 60" 11/16" 3mm 5mm — 33 28
Casement – Non-Impact Laminated Insulating Glass
24" x 60" 1" 3mm 7mm PVB — 36 29
24" x 60" 1" 5mm 7mm PVB — 37 29
Casement – Triple-Pane Insulating Glass
24" x 60" 1-1/4" 3mm 3mm 3mm 29 24
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-3
350 Series Casement
Glazing (Insulating Glass)
Glazing Type
Dual-pane insulating glass S
Triple-pane insulating glass O
Insulated Glass Options / Low-E Types
Advanced Low-E S
NaturalSun Low-E O
SunDefense™ Low-E 1 O
Gray Low-E 1 O
Bronze-tinted Advanced Low-E 1 O
Additional Glazing Options
Annealed glass S
Tempered glass O
Obscure glass 2 O
Noise reduction glass (STC 3mm / 5mm combination) 1 O
Noise Reduction laminated glass (non-impact) 1 O
Gas Fi l l / High Alt i tude
Argon S
High altitude O
High altitude with argon 1 O
Sash
Foam Insulation O
Performance Upgrade O
Interior / Exterior Color
White Interior/White Exterior S
Almond Interior/Almond Exterior O
White Interior/Brown Exterior O
White Interior/Fossil Exterior O
White Interior/Black Exterior O
White Interior/Brick Red Exterior O
White Interior/Hartford Green Exterior O
White Interior/Morning Sky Gray Exterior O
White Interior/Poplar White Exterior O
White Interior/Portobello Exterior O
White Interior/Tan Exterior O
Hardware
Color matched hardware S
Bright Brass, Satin Nickel or Oil-Rubbed Bronze O
Screens
Conventional black fiberglass screens - flat S
InView™ screens O
S = Standard; O = Optional
(1) Not available with triple-pane glazing.
(2) Contact your local Pella sales representative for current offering.
Features and Options
Grilles
Gri l les-Between-the-Glass
3/4" Contour O
1" Contour O
Grille Patterns: Traditional, Prairie, Top Row, Custom - Equally Divided O
Simulated-Divided-Light Gri l les 1 (without spacer)
7/8" contour profile O
Grille Patterns: Traditional, Prairie, Top Row, Custom - Equally Divided O
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-4
350 Series CasementG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent 11/16" Dual-Pane with 3mm Glass N NC SC S CA11/16" Advanced Low-E IG PEL-N-184-01363-00001 3 3 Air 0.28 0.24 0.44 59 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01363-00002 0.28 0.22 0.39 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01363-00003 0.28 0.22 0.39 59 NC SC S
11/16" Advanced Low-E IG PEL-N-184-01364-00001 3 3 Argon 0.25 0.23 0.44 62 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01364-00002 0.25 0.21 0.39 62 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01364-00003 0.25 0.21 0.39 62 N NC SC S
11/16" NaturalSun Low-E IG PEL-N-184-01323-00001 3 3 Air 0.29 0.43 0.49 58 N
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01323-00002 0.29 0.39 0.44 58 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01323-00003 0.29 0.39 0.44 58 N NC
11/16" NaturalSun Low-E IG PEL-N-184-01324-00001 3 3 Argon 0.26 0.43 0.49 62 N
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01324-00002 0.26 0.39 0.44 62 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01324-00003 0.26 0.39 0.44 62 N NC
11/16" SunDefense™ Low-E IG PEL-N-184-01389-00001 3 3 Air 0.28 0.18 0.40 59 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01389-00002 0.28 0.16 0.36 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01389-00003 0.28 0.16 0.36 59 NC SC S
11/16" SunDefense Low-E IG PEL-N-184-01390-00001 3 3 Argon 0.25 0.18 0.40 63 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01390-00002 0.25 0.16 0.36 63 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01390-00003 0.25 0.16 0.36 63 N NC SC S
Vent — with Foam Inserts11/16" Advanced Low-E IG PEL-N-184-01445-00001 3 3 Air 0.28 0.24 0.44 59 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01445-00002 0.28 0.22 0.39 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01445-00003 0.28 0.22 0.39 59 NC SC S
11/16" Advanced Low-E IG PEL-N-184-01446-00001 3 3 Argon 0.25 0.23 0.44 63 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01446-00002 0.25 0.21 0.39 63 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01446-00003 0.25 0.21 0.39 63 N NC SC S
11/16" NaturalSun Low-E IG PEL-N-184-01409-00001 3 3 Air 0.29 0.43 0.49 58 N
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01409-00002 0.29 0.39 0.44 58 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01409-00003 0.29 0.39 0.44 58 N NC
11/16" NaturalSun Low-E IG PEL-N-184-01410-00001 3 3 Argon 0.26 0.43 0.49 62 N
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01410-00002 0.26 0.39 0.44 62 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01410-00003 0.26 0.39 0.44 62 N NC
11/16" SunDefense™ Low-E IG PEL-N-184-01463-00001 3 3 Air 0.28 0.18 0.40 59 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01463-00002 0.28 0.16 0.36 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01463-00003 0.28 0.16 0.36 59 NC SC S
11/16" SunDefense Low-E IG PEL-N-184-01464-00001 3 3 Argon 0.24 0.18 0.40 63 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01464-00002 0.24 0.16 0.36 63 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01464-00003 0.24 0.16 0.36 63 N NC SC S
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
Glazing Performance - Total Unit
CA
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-5
350 Series Casement
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
Gla
ss
Thic
knes
s
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent 1" Dual-Pane with 5mm Glass N NC SC S CA1" Advanced Low-E IG PEL-N-184-01367-00001 5 5 Air 0.28 0.23 0.43 57 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01367-00002 0.28 0.21 0.38 57 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01367-00003 0.28 0.21 0.38 57 NC SC S
1" Advanced Low-E IG PEL-N-184-01368-00001 5 5 Argon 0.25 0.23 0.43 61 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01368-00002 0.25 0.21 0.38 61 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01368-00003 0.25 0.21 0.38 61 N NC SC S
1" NaturalSun Low-E IG PEL-N-184-01327-00001 5 5 Air 0.29 0.41 0.48 57 N
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01327-00002 0.29 0.37 0.43 57 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01327-00003 0.29 0.37 0.43 57 N NC
1" NaturalSun Low-E IG PEL-N-184-01328-00001 5 5 Argon 0.26 0.41 0.48 60 N
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01328-00002 0.26 0.38 0.43 60 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01328-00003 0.26 0.38 0.43 60 N NC
1" SunDefense™ Low-E IG PEL-N-184-01393-00001 5 5 Air 0.28 0.18 0.39 58 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01393-00002 0.28 0.16 0.36 58 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01393-00003 0.28 0.16 0.36 58 NC SC S
1" SunDefense Low-E IG PEL-N-184-01394-00001 5 5 Argon 0.25 0.17 0.39 61 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01394-00002 0.25 0.16 0.36 61 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01394-00003 0.25 0.16 0.36 61 N NC SC S
Vent — with Foam Inserts1" Advanced Low-E IG PEL-N-184-01449-00001 5 5 Air 0.28 0.23 0.43 58 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01449-00002 0.28 0.21 0.38 58 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01449-00003 0.28 0.21 0.38 58 NC SC S
1" Advanced Low-E IG PEL-N-184-01450-00001 5 5 Argon 0.25 0.23 0.43 61 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01450-00002 0.25 0.21 0.38 61 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01450-00003 0.25 0.21 0.38 61 N NC SC S
1" NaturalSun Low-E IG PEL-N-184-01413-00001 5 5 Air 0.29 0.41 0.48 57 N
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01413-00002 0.29 0.37 0.43 57 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01413-00003 0.29 0.37 0.43 57 N NC
1" NaturalSun Low-E IG PEL-N-184-01414-00001 5 5 Argon 0.26 0.41 0.48 60 N
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01414-00002 0.26 0.38 0.43 60 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01414-00003 0.26 0.38 0.43 60 N NC
1" SunDefense™ Low-E IG PEL-N-184-01467-00001 5 5 Air 0.28 0.18 0.39 58 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01467-00002 0.28 0.16 0.36 58 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01467-00003 0.28 0.16 0.36 58 NC SC S
1" SunDefense Low-E IG PEL-N-184-01468-00001 5 5 Argon 0.25 0.17 0.39 61 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01468-00002 0.25 0.16 0.36 61 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01468-00003 0.25 0.16 0.36 61 N NC SC S
Glazing Performance - Total Unit
CA
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-6
350 Series CasementG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent Dual-Pane Tinted Glass N NC SC S CA11/16" Bronze Advanced Low-E IG PEL-N-184-01381-00001 3 3 Air 0.28 0.23 0.32 59 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01381-00002 0.28 0.21 0.29 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01381-00003 0.28 0.21 0.29 59 NC SC S
11/16" Bronze Advanced Low-E IG PEL-N-184-01382-00001 3 3 Argon 0.25 0.23 0.32 63 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01382-00002 0.25 0.21 0.29 63 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01382-00003 0.25 0.21 0.29 63 N NC SC S
11/16" Gray Low-E IG PEL-N-184-01339-00001 3 3 Air 0.28 0.17 0.25 58 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01339-00002 0.28 0.15 0.22 58 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01339-00003 0.28 0.15 0.22 58 NC SC S
11/16" Gray Low-E IG PEL-N-184-01340-00001 3 3 Argon 0.25 0.16 0.25 62 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01340-00002 0.25 0.15 0.22 62 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01340-00003 0.25 0.15 0.22 62 N NC SC S
Tinted Glazing — with Foam Inserts11/16" Bronze Advanced Low-E IG PEL-N-184-01455-00001 3 3 Air 0.28 0.23 0.32 59 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01455-00002 0.28 0.21 0.29 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01455-00003 0.28 0.21 0.29 59 NC SC S
11/16" Bronze Advanced Low-E IG PEL-N-184-01456-00001 3 3 Argon 0.25 0.23 0.32 63 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01456-00002 0.25 0.21 0.29 63 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01456-00003 0.25 0.21 0.29 63 N NC SC S
11/16" Gray Low-E IG PEL-N-184-01425-00001 3 3 Air 0.28 0.17 0.25 58 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01425-00002 0.28 0.15 0.22 58 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01425-00003 0.28 0.15 0.22 58 NC SC S
11/16" Gray Low-E IG PEL-N-184-01426-00001 3 3 Argon 0.25 0.16 0.25 62 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01426-00002 0.25 0.15 0.22 62 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01426-00003 0.25 0.15 0.22 62 N NC SC S
Glazing Performance - Total Unit
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
CA
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-7
350 Series CasementG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent Dual-Pane Tinted Glass N NC SC S CA1" Bronze Advanced Low-E IG PEL-N-184-01385-00001 5 5 Air 0.28 0.21 0.28 57 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01385-00002 0.28 0.19 0.25 57 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01385-00003 0.28 0.19 0.25 57 NC SC S
1" Bronze Advanced Low-E IG PEL-N-184-01386-00001 5 5 Argon 0.25 0.21 0.28 61 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01386-00002 0.25 0.19 0.25 61 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01386-00003 0.25 0.19 0.25 61 N NC SC S
1" Gray Low-E IG PEL-N-184-01343-00001 5 5 Air 0.28 0.16 0.24 57 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01343-00002 0.28 0.15 0.22 57 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01343-00003 0.28 0.15 0.22 57 NC SC S
1" Gray Low-E IG PEL-N-184-01344-00001 5 5 Argon 0.26 0.16 0.24 60 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01344-00002 0.26 0.14 0.22 60 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01344-00003 0.26 0.14 0.22 60 N NC SC S
Tinted Glazing — with Foam Inserts1" Bronze Advanced Low-E IG PEL-N-184-01459-00001 5 5 Air 0.28 0.21 0.28 58 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01459-00002 0.28 0.19 0.25 58 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01459-00003 0.28 0.19 0.25 58 NC SC S
1" Bronze Advanced Low-E IG PEL-N-184-01460-00001 5 5 Argon 0.25 0.21 0.28 61 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01460-00002 0.25 0.19 0.25 61 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01460-00003 0.25 0.19 0.25 61 N NC SC S
1" Gray Low-E IG PEL-N-184-01429-00001 5 5 Air 0.28 0.16 0.24 57 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01429-00002 0.28 0.15 0.22 57 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01429-00003 0.28 0.15 0.22 57 NC SC S
1" Gray Low-E IG PEL-N-184-01430-00001 5 5 Argon 0.26 0.16 0.24 60 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01430-00002 0.26 0.14 0.22 60 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01430-00003 0.26 0.14 0.22 60 N NC SC S
Glazing Performance - Total Unit
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
CA
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-8
350 Series CasementG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent 1" Dual-Pane Non-Impact Laminated Glass N NC SC S CA1" Advanced Low-E PVB IG PEL-N-184-01369-00001 3 6 Air 0.28 0.23 0.43 59 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01369-00002 0.28 0.21 0.38 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01369-00003 0.28 0.21 0.38 59 NC SC S
1" Advanced Low-E PVB IG PEL-N-184-01370-00001 3 6 Argon 0.25 0.23 0.43 63 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01370-00002 0.25 0.21 0.38 63 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01370-00003 0.25 0.21 0.38 63 N NC SC S
1" Advanced Low-E PVB IG PEL-N-184-01333-00001 3 6 Air 0.28 0.40 0.48 58 N NC
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01333-00002 0.28 0.36 0.43 58 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01333-00003 0.28 0.36 0.43 58 N NC
1" Advanced Low-E PVB IG PEL-N-184-01334-00001 3 6 Argon 0.26 0.40 0.48 62 N NC
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01334-00002 0.26 0.36 0.43 62 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01334-00003 0.26 0.36 0.43 62 N NC
1" NaturalSun Low-E PVB IG PEL-N-184-01395-00001 3 6 Air 0.28 0.17 0.39 59 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01395-00002 0.28 0.16 0.35 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01395-00003 0.28 0.16 0.35 59 NC SC S
1" NaturalSun Low-E PVB IG PEL-N-184-01396-00001 3 6 Argon 0.25 0.17 0.39 63 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01396-00002 0.25 0.16 0.35 63 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01396-00003 0.25 0.16 0.35 63 N NC SC S
1" NaturalSun Low-E PVB IG PEL-N-184-01371-00001 5 6 Air 0.28 0.23 0.42 59 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01371-00002 0.28 0.21 0.38 59 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01371-00003 0.28 0.21 0.38 59 NC SC S
1" NaturalSun Low-E PVB IG PEL-N-184-01372-00001 5 6 Argon 0.25 0.22 0.42 62 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01372-00002 0.25 0.20 0.38 62 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01372-00003 0.25 0.20 0.38 62 N NC SC S
1" SunDefense™ Low-E PVB IG PEL-N-184-01335-00001 5 6 Air 0.28 0.38 0.48 58 N NC
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01335-00002 0.28 0.35 0.43 58 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01335-00003 0.28 0.35 0.43 58 N NC
1" SunDefense Low-E PVB IG PEL-N-184-01336-00001 5 6 Argon 0.26 0.38 0.48 61 N NC
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01336-00002 0.26 0.35 0.43 61 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01336-00003 0.26 0.35 0.43 61 N NC
1" SunDefense™ Low-E PVB IG PEL-N-184-01397-00001 5 6 Air 0.27 0.17 0.39 59 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01397-00002 0.27 0.16 0.35 59 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01397-00003 0.27 0.16 0.35 59 N NC SC S
1" SunDefense Low-E PVB IG PEL-N-184-01398-00001 5 6 Argon 0.25 0.17 0.39 63 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01398-00002 0.25 0.16 0.35 63 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01398-00003 0.25 0.16 0.35 63 N NC SC S
Glazing Performance - Total Unit
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
CA
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-9
350 Series CasementG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent 1" Dual-Pane Non-Impact Tinted Laminated Glass N NC SC S CA1" Bronze Advanced Low-E PVB IG PEL-N-187-01809-00001 3 7 Air 0.28 0.23 0.33 55 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-187-01809-00002 0.28 0.21 0.29 55 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-187-01809-00003 0.28 0.21 0.29 55 NC SC S
1" Bronze Advanced Low-E PVB IG PEL-N-187-01810-00001 3 7 Argon 0.25 0.23 0.33 58 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-187-01810-00002 0.25 0.21 0.29 58 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-187-01810-00003 0.25 0.21 0.29 58 N NC SC S
1" Gray Advanced Low-E PVB IG PEL-N-187-01805-00001 3 6 Air 0.29 0.16 0.24 55 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-187-01805-00002 0.29 0.15 0.22 55 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-187-01805-00003 0.29 0.15 0.22 55 NC SC S
1" Gray Advanced Low-E PVB IG PEL-N-187-01806-00001 3 6 Argon 0.26 0.16 0.24 58 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-187-01806-00002 0.26 0.14 0.22 58 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-187-01806-00003 0.26 0.14 0.22 58 N NC SC S
1" Bronze Advanced Low-E PVB IG PEL-N-187-01811-00001 5 7 Air 0.28 0.22 0.32 57 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-187-01811-00002 0.28 0.20 0.29 57 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-187-01811-00003 0.28 0.20 0.29 57 NC SC S
1" Bronze Advanced Low-E PVB IG PEL-N-187-01812-00001 5 7 Argon 0.25 0.22 0.32 61 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-187-01812-00002 0.25 0.20 0.29 61 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-187-01812-00003 0.25 0.20 0.29 61 N NC SC S
1" Gray Advanced Low-E PVB IG PEL-N-187-01807-00001 5 6 Air 0.28 0.16 0.24 57 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-187-01807-00002 0.28 0.15 0.21 57 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-187-01807-00003 0.28 0.15 0.21 57 NC SC S
1" Gray Advanced Low-E PVB IG PEL-N-187-01808-00001 5 6 Argon 0.26 0.15 0.24 61 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-187-01808-00002 0.26 0.14 0.21 61 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-187-01808-00003 0.26 0.14 0.21 61 N NC SC S
Glazing Performance - Total Unit
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
CA
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-10
350 Series Casement
Glazing Performance - Total Unit
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
CA
Gla
ss
Thic
knes
s
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext. Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent 11/16" Dual-Pane with 5mm/3mm Glass N NC SC S CA11/16" Advanced Low-E IG PEL-N-184-01365-00001 5 3 Air 0.29 0.23 0.43 57 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01477-00001 0.30 0.21 0.39 57 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01365-00002 0.29 0.21 0.39 57 NC SC S
11/16" Advanced Low-E IG PEL-N-184-01366-00001 5 3 Argon 0.26 0.23 0.43 61 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01478-00001 0.27 0.21 0.39 61 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01366-00002 0.26 0.21 0.39 61 N NC SC S
11/16" NaturalSun Low-E IG PEL-N-184-01325-00001 5 3 Air 0.30 0.41 0.49 56
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01473-00001 0.31 0.37 0.44 56
with 7/8" Simulated Divided Light grilles PEL-N-184-01325-00002 0.30 0.37 0.44 56 NC
11/16" NaturalSun Low-E IG PEL-N-184-01326-00001 5 3 Argon 0.27 0.41 0.49 61 N
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01474-00001 0.28 0.38 0.44 61 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01326-00002 0.27 0.38 0.44 61 N NC
11/16" SunDefense™ Low-E IG PEL-N-184-01391-00001 5 3 Air 0.29 0.18 0.40 57 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01481-00001 0.30 0.17 0.36 57 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01391-00002 0.29 0.17 0.36 57 NC SC S
11/16" SunDefense Low-E IG PEL-N-184-01392-00001 5 3 Argon 0.25 0.18 0.40 62 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01482-00001 0.27 0.16 0.36 62 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01392-00002 0.25 0.16 0.36 62 N NC SC S
Vent — with Foam Inserts11/16" Advanced Low-E IG PEL-N-184-01447-00001 5 3 Air 0.29 0.23 0.43 57 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01497-00001 0.30 0.21 0.39 57 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01447-00002 0.29 0.21 0.39 57 NC SC S
11/16" Advanced Low-E IG PEL-N-184-01448-00001 5 3 Argon 0.26 0.23 0.43 61 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01498-00001 0.27 0.21 0.39 61 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01448-00002 0.26 0.21 0.39 61 N NC SC S
11/16" NaturalSun Low-E IG PEL-N-184-01411-00001 5 3 Air 0.30 0.41 0.49 56
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01493-00001 0.31 0.37 0.44 56
with 7/8" Simulated Divided Light grilles PEL-N-184-01411-00002 0.30 0.37 0.44 56 NC
11/16" NaturalSun Low-E IG PEL-N-184-01412-00001 5 3 Argon 0.26 0.41 0.49 61 N
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01494-00001 0.27 0.38 0.44 61 N NC
with 7/8" Simulated Divided Light grilles PEL-N-184-01412-00002 0.26 0.38 0.44 61 N NC
11/16" SunDefense™ Low-E IG PEL-N-184-01465-00001 5 3 Air 0.29 0.18 0.40 57 NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01501-00001 0.30 0.17 0.36 57 NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01465-00002 0.29 0.17 0.36 57 NC SC S
11/16" SunDefense Low-E IG PEL-N-184-01466-00001 5 3 Argon 0.25 0.18 0.40 62 N NC SC S
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01502-00001 0.26 0.16 0.36 62 N NC SC S
with 7/8" Simulated Divided Light grilles PEL-N-184-01466-00002 0.25 0.16 0.36 62 N NC SC S
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-11
350 Series CasementG
lass
Th
ickn
ess
Type of Glazing NFRC Certified Product #
Glass (mm)
Gap Fill
Performance Values 1
Shaded Areas Meet ENERGY STAR® Performance Criteria in Zones Shown
Ext
.
Mid
.
Int.
U-F
acto
r
SHG
C
VLT CR
U. S. Canada 2
Zone ER Zone
Vent - Triple-Pane Insulating Glass N NC SC S CA1-1/4" Advanced Low-E Triple-pane IG PEL-N-184-01359-00001 3 3 3 Air 0.19 0.20 0.34 73 N NC SC S 28 CA
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01359-00002 0.19 0.18 0.30 73 N NC SC S 27 CA
1-1/4" Advanced Low-E Triple-pane IG PEL-N-184-01360-00001 3 3 3 Argon 0.17 0.20 0.34 77 N NC SC S 30 CA with 3/4" or 1" grilles-between-the-glass PEL-N-184-01360-00002 0.17 0.18 0.30 77 N NC SC S 29 CA
1-1/4" NaturalSun Low-E Triple-pane IG PEL-N-184-01329-00001 3 3 3 Air 0.23 0.39 0.45 67 N NC 34 CA with 3/4" or 1" grilles-between-the-glass PEL-N-184-01329-00002 0.23 0.35 0.41 67 N NC
1-1/4" NaturalSun Low-E Triple-pane IG PEL-N-184-01330-00001 3 3 3 Argon 0.21 0.39 0.45 70 N NC 36 CA with 3/4" or 1" grilles-between-the-glass PEL-N-184-01330-00002 0.21 0.35 0.41 70 N NC 34 CA
1-7/16" Advanced Low-E Triple-pane IG PEL-N-184-01357-00001 5 5 5 Air 0.19 0.19 0.33 71 N NC SC S 27 CA with 3/4" or 1" grilles-between-the-glass PEL-N-184-01357-00002 0.19 0.18 0.30 71 N NC SC S 27 CA
1-7/16" Advanced Low-E Triple-pane IG PEL-N-184-01358-00001 5 5 5 Argon 0.17 0.19 0.33 75 N NC SC S 30 CA with 3/4" or 1" grilles-between-the-glass PEL-N-184-01358-00002 0.17 0.18 0.30 75 N NC SC S 29 CA
1-7/16" NaturalSun Low-E Triple-pane IG PEL-N-184-01331-00001 5 5 5 Air 0.23 0.37 0.44 66 N NC with 3/4" or 1" grilles-between-the-glass PEL-N-184-01331-00002 0.23 0.33 0.39 66 N NC
1-7/16" NaturalSun Low-E Triple-pane IG PEL-N-184-01332-00001 5 5 5 Argon 0.21 0.36 0.44 69 N NC 35 CA
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01332-00002 0.21 0.33 0.39 69 N NC 33 CA
Vent - Triple-Pane Insulating Glass — with Foam Inserts1-1/4" Advanced Low-E Triple-pane IG PEL-N-184-01441-00001 3 3 3 Air 0.19 0.20 0.34 73 N NC SC S 28 CA
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01441-00002 0.19 0.18 0.30 73 N NC SC S 27 CA
1-1/4" Advanced Low-E Triple-pane IG PEL-N-184-01442-00001 3 3 3 Argon 0.17 0.20 0.34 77 N NC SC S 30 CA with 3/4" or 1" grilles-between-the-glass PEL-N-184-01442-00002 0.17 0.18 0.30 77 N NC SC S 29 CA
1-1/4" NaturalSun Low-E Triple-pane IG PEL-N-184-01415-00001 3 3 3 Air 0.23 0.39 0.45 67 N NC 34 CA with 3/4" or 1" grilles-between-the-glass PEL-N-184-01415-00002 0.23 0.35 0.41 67 N NC
1-1/4" NaturalSun Low-E Triple-pane IG PEL-N-184-01416-00001 3 3 3 Argon 0.20 0.39 0.45 70 N NC 37 CA with 3/4" or 1" grilles-between-the-glass PEL-N-184-01416-00002 0.20 0.35 0.41 70 N NC 35 CA
1-7/16" Advanced Low-E Triple-pane IG PEL-N-184-01439-00001 5 5 5 Air 0.19 0.19 0.33 71 N NC SC S 27 CA with 3/4" or 1" grilles-between-the-glass PEL-N-184-01439-00002 0.19 0.18 0.30 71 N NC SC S 27 CA
1-7/16" Advanced Low-E Triple-pane IG PEL-N-184-01440-00001 5 5 5 Argon 0.17 0.19 0.33 75 N NC SC S 30 CA with 3/4" or 1" grilles-between-the-glass PEL-N-184-01440-00002 0.17 0.18 0.30 75 N NC SC S 29 CA
1-7/16" NaturalSun Low-E Triple-pane IG PEL-N-184-01417-00001 5 5 5 Air 0.23 0.37 0.44 66 N NC with 3/4" or 1" grilles-between-the-glass PEL-N-184-01417-00002 0.23 0.33 0.39 66 N NC
1-7/16" NaturalSun Low-E Triple-pane IG PEL-N-184-01418-00001 5 5 5 Argon 0.20 0.36 0.44 69 N NC 36 CA
with 3/4" or 1" grilles-between-the-glass PEL-N-184-01418-00002 0.20 0.33 0.39 69 N NC 34 CA
Glazing Performance - Total Unit
(1) Glazing performance values are calculated based on NFRC 100, NFRC 200 and NFRC 500.
ENERGY STAR® values are updated to 2016 (Version 6) criteria.
(2) The values shown are based on Canada's updated ENERGY STAR® 2020 initiative.
Based on unit size, some products will use 2.5mm glass that may have improved glazing performance from what is shown.
See the Product Performance section for more detailed information or visit www.energystar.gov for Energy Star guidelines.
R-Value = 1/U-Factor
SHGC = Solar Heat Gain Coefficient
VLT % = Visible Light Transmission
CR = Condensation Resistance
ER = Canadian Energy Rating
Climate Zones
CA
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-12
350 Series Casement
For traditional patterns, see size tables.
1"3/4"
1" Contour3/4" Contour1" Contour
1"
3/4" Contour
3/4"
Simulated Divided Light7/8"
7/8"
Grille Profiles Grilles-Between-the-Glass Simulated-Divided-Light Grilles
Grilles
9-Lite Prairie
Traditional
- Specify number of lites.
- Grilles must be equally divided on visible glass.
- Minimum 6" x 6".
Top Row
- Standard visible glass to separator bar = 14" or half of total visible glass height, whichever is smaller.
Prairie
- Approximately 4" from edge of sash to center of bar
- Minimum actual glass is 13"
Grille Patterns Prairie Lite Patterns
Other Available Patterns
Traditional Top Row Custom — Equally Divided
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-13
350 Series Casement
3-0/6-02-8/6-02-6/6-02-4/6-02-0/6-01-6/6-0
3-0/5-62-8/5-62-6/5-62-4/5-62-0/5-61-6/5-6
3-0/5-02-8/5-02-6/5-02-4/5-02-0/5-01-6/5-0
3-0/4-62-8/4-62-6/4-62-4/4-62-0/4-61-6/4-6
3-0/4-02-8/4-02-6/4-02-4/4-02-0/4-01-6/4-0
3-0/3-62-8/3-62-6/3-62-4/3-62-0/3-61-6/3-6
2-6/3-0
2-6/2-6
3-0/3-02-8/3-02-4/3-02-0/3-01-6/3-0
2-4/2-62-0/2-61-6/2-6
E2E2E
E2E2E
E2E2E
E2E2E
E2E2E
E2E3E
"/ 21
71(1 8
16)
(1 8
29)
6' 0
"
"/ 21
65(1 6
64)
(1 6
76)
5' 6
"
"/ 21
59(1 5
11)
(1 5
24)
5' 0
"
"/ 21
53(1 3
59)
(1 3
72)
4' 6
"
"/ 21
47(1 2
07)
(1 2
19)
4' 0
"
2' 6"
"/21
(762)(749)
29
"/ 21
41
(914)
"/21
(902)
35
3' 0"
"/21
(610)(457) (711)
"/2117
1' 6"
(445)
"/2123
2' 0"
(597)
27
2' 4"
(699)(813)
"/21
(800)
31
2' 8"
1-Wide Vent
Opening
Frame
29(749
)(7
62)
(902
)(1
054
)(1
067
)(9
14) "/ 21
35"
/ 21
3' 6
"2'
6"
3' 0
"
Not to scale.
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
E2 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E3 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
Size Tables
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-14
350 Series Casement
Miscellaneous Formulas
1-Wide—Vent
Visible GlassVGW = FW – 7"
VGH = FH – 7"
Actual Glass AGW = FW – 5-7/8"
AGH = FH – 5-7/8"
Key:
AGW = Actual Glass Width AGH = Actual Glass Height FW = Frame Width FH = Frame Height VGW = Visible Glass Width VGH = Visible Glass Height COW = Clear opening width COH = Clear opening height
Clear Opening Formulas
1-Wide—Vent
Vent Area VA = (COH X COW) ÷ 144
COH COH = FH - 5.5
COW
Standard Performance COW = FW - 11.8125
Side Pivot COW = FW - 7.543
Side pivot hardware only available on frame widths of 28" to 32"
The clear opening formulas do not apply to units with FW < 16.25”
1-Wide Vent Unit
MINIMUM13-1/2" W x 17-1/2" H
(343 x 445)
MAXIMUM35-1/2" W x 71-1/2" H
(889 x 1 803)
General Notes:
• To convert areas to square meters (m 2), multiply square feet by 0.0929.• Rough Opening = Frame Dimension + 1/2".• Unit Height must be > Unit Width• Keep frame di men sions to the near est 1/8" increment.• Tempered glass must measure ≥ 18-1/2" diagonally.• If glass width to height ratio is > 5 to 1, then unit must be tempered.
Special Sizes and Dimensions
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-15
350 Series Casement
(1) Maximum performance when glazed with the appropriate glass thickness.
VENT UNITS
Unit
Eg
ress Frame (Inches)
Clear Opening (Inches) (Vent Units Only) Vent
Area Ft2
Visible Glass
Ft2
Standard Glass Thickness (mm)
Performance Class & Grade 1
Width Height Width Height Ft2 Annealed Tempered Standard Upgrade
1-6/2-6 17-1/2 29-1/2 5-11/16 24 0.9 0.9 1.6 2.5 3 LC40 LC601-6/3-0 17-1/2 35-1/2 5-11/16 30 1.1 1.1 2.1 2.5 3 LC40 LC601-6/3-6 17-1/2 41-1/2 5-11/16 36 1.4 1.4 2.5 2.5 3 LC40 LC601-6/4-0 17-1/2 47-1/2 5-11/16 42 1.6 1.6 3.0 2.5 3 LC40 LC601-6/4-6 17-1/2 53-1/2 5-11/16 48 1.8 1.8 3.4 2.5 3 LC40 LC601-6/5-0 17-1/2 59-1/2 5-11/16 54 2.1 2.1 3.8 2.5 3 LC40 LC601-6/5-6 17-1/2 65-1/2 5-11/16 60 2.3 2.3 4.3 2.5 3 LC40 LC601-6/6-0 17-1/2 71-1/2 5-11/16 66 2.6 2.6 4.7 2.5 3 LC40 LC602-0/2-6 23-1/2 29-1/2 11-11/16 24 1.9 1.9 2.6 2.5 3 LC40 LC602-0/3-0 23-1/2 35-1/2 11-11/16 30 2.4 2.4 3.3 2.5 3 LC40 LC602-0/3-6 23-1/2 41-1/2 11-11/16 36 2.9 2.9 4.0 2.5 3 LC40 LC602-0/4-0 23-1/2 47-1/2 11-11/16 42 3.4 3.4 4.6 2.5 3 LC40 LC602-0/4-6 23-1/2 53-1/2 11-11/16 48 3.8 3.8 5.3 2.5 3 LC40 LC602-0/5-0 23-1/2 59-1/2 11-11/16 54 4.3 4.3 6.0 2.5 3 LC40 LC602-0/5-6 23-1/2 65-1/2 11-11/16 60 4.8 4.8 6.7 2.5 3 LC40 LC602-0/6-0 23-1/2 71-1/2 11-11/16 66 5.3 5.3 7.4 3 3 LC40 LC602-4/2-6 27-1/2 29-1/2 15-11/16 24 2.6 2.6 3.2 2.5 3 LC40 LC602-4/3-0 27-1/2 35-1/2 15-11/16 30 3.2 3.2 4.1 2.5 3 LC40 LC602-4/3-6 27-1/2 41-1/2 15-11/16 36 3.9 3.9 4.9 2.5 3 LC40 LC602-4/4-0 27-1/2 47-1/2 15-11/16 42 4.5 4.5 5.8 2.5 3 LC40 LC602-4/4-6 27-1/2 53-1/2 15-11/16 48 5.2 5.2 6.6 2.5 3 LC40 LC602-4/5-0 27-1/2 59-1/2 15-11/16 54 5.8 5.8 7.5 3 3 LC40 LC602-4/5-6 27-1/2 65-1/2 15-11/16 60 6.5 6.5 8.3 3 3 LC40 LC602-4/6-0 27-1/2 71-1/2 15-11/16 66 7.1 7.1 9.2 3 3 LC40 LC602-6/2-6 29-1/2 29-1/2 17-11/16 24 2.9 2.9 3.5 2.5 3 LC40 LC602-6/3-0 29-1/2 35-1/2 17-11/16 30 3.6 3.6 4.5 2.5 3 LC40 LC602-6/3-6 E3 29-1/2 41-1/2 22 36 5.4 4.4 5.4 2.5 3 LC40 LC602-6/4-0 E2 29-1/2 47-1/2 22 42 6.4 5.1 6.3 2.5 3 LC40 LC602-6/4-6 E2 29-1/2 53-1/2 22 48 7.3 5.8 7.3 2.5 3 LC40 LC602-6/5-0 E2 29-1/2 59-1/2 22 54 8.2 6.6 8.2 3 3 LC40 LC602-6/5-6 E2 29-1/2 65-1/2 22 60 9.1 7.3 9.1 3 3 LC40 LC602-6/6-0 E2 29-1/2 71-1/2 22 66 10.0 8.1 10.1 3 3 LC40 LC602-8/3-0 31-1/2 35-1/2 19-11/16 30 4.0 4.0 4.8 2.5 3 LC40 LC602-8/3-6 E2 31-1/2 41-1/2 24 36 5.9 4.9 5.9 2.5 3 LC40 LC602-8/4-0 E2 31-1/2 47-1/2 24 42 6.9 5.7 6.9 2.5 3 LC40 LC602-8/4-6 E2 31-1/2 53-1/2 24 48 7.9 6.5 7.9 2.5 3 LC40 LC602-8/5-0 E2 31-1/2 59-1/2 24 54 8.9 7.3 8.9 3 3 LC40 LC602-8/5-6 E2 31-1/2 65-1/2 24 60 9.9 8.1 10.0 3 3 LC40 LC602-8/6-0 E2 31-1/2 71-1/2 24 66 10.9 9.0 11.0 3 3 LC40 LC603-0/3-0 35-1/2 35-1/2 23-11/16 30 4.9 4.9 5.6 2.5 3 LC40 LC603-0/3-6 E 35-1/2 41-1/2 23-11/16 36 5.9 5.9 6.8 2.5 3 LC40 LC603-0/4-0 E 35-1/2 47-1/2 23-11/16 42 6.9 6.9 8.0 2.5 3 LC40 LC603-0/4-6 E 35-1/2 53-1/2 23-11/16 48 7.8 7.8 9.2 2.5 3 LC40 LC603-0/5-0 E 35-1/2 59-1/2 23-11/16 54 8.8 8.8 10.4 3 3 LC40 LC603-0/5-6 E 35-1/2 65-1/2 23-11/16 60 9.8 9.8 11.6 3 3 LC40 LC603-0/6-0 E 35-1/2 71-1/2 23-11/16 66 10.8 10.8 12.8 3 3 LC40 LC60
Egress Notes:
Check all applicable local codes for emergency egress requirements.
E = Window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E1 = Window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
E2 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.7 ft 2.
E3 = With optional side pivot hardware, window meets minimum clear opening of 24" height, 20" width, and 5.0 ft 2.
To convert areas to square meters (m²), multiply square feet by 0.0929.
Design Data
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-16
350 Series Casement
1) Foam Insulation is not available with Performance Upgrade.
(2) Dual-Pane IG High Altitude glazing available with or without Argon. Triple-Pane IG High Altitude only available without Argon.
(3) Obscure glass not available with Bronze Advanced Low-E IG.
(4) Almond grilles only available on almond units. Almond units with grilles will have an almond grille color.
Frame • Overall frame depth: 4-1/2" on all frame types except the 3-1/4” pocket
replacement frame.• Frame members are mitered and heat fused to provide a fully welded
corner assembly.• Frame: [1-7/16" setback nail fin for 3-1/16" wall depth] [Block frame for
4-1/2" wall depth] [Block frame for 3-1/4" pocket replacement install] [Flush flange for 4" wall depth] [Integral flange for 3-7/8" wall depth].
• Interior and exterior frame surfaces are extruded rigid uPVC.
Sash
• Sash members are extruded rigid uPVC [with optional foam Insulation 1].• Panel members are mitered and heat-fused to provide a fully welded
corner assembly with SmoothSeam™ virtually invisible interior welds. • Contains sealed insulating glass.
Weatherstripping• Vent is weatherstripped around the sash with rainstrip and the frame
perimeter is weatherstripped with an extruded bulb weatherstrip in two locations.
Glazing System• Quality float glass complying with ASTM C 1036.• Exterior face-glazed sealed insulating glass. • Dual-Pane insulating glass [[annealed] [tempered]] [Advanced
Low-E coated [with Argon]] [NaturalSun Low-E coated [with Argon]] [SunDefense™ Low-E coated [with Argon]] [Bronze, Advanced Low-E coated [with Argon]] [Gray Low-E coated [with Argon]] [Obscure 3] [High Altitude 2] [Tempered].
-or-• Triple-Pane insulating glass [[annealed] [tempered]] [Advanced Low-E
coated with Argon] [NaturalSun Low-E coated with Argon] [Obscure 3] [High Altitude 2] [Tempered].
Interior / Exterior• Window frame and sash members are [[White] [Almond] with integral color
extruded throughout the profiles] [[Brown] [Black] [Brick Red] [Hartford Green] [Morning Sky Gray] [Poplar White] [Portobello] [Tan] [Fossil] exterior, consisting of a solar reflective coating exceeding AAMA 613 test requirements, with White integral color extruded throughout the profiles on the interior].
• All exposed PVC surfaces are smooth, glossy and uniform in appearance.
Hardware • Multipoint unison lock with single handle is factory-installed zinc die cast.
Lock tie-bars are [steel] [stainless steel].• High quality [steel] [stainless steel] dual-arm roto operator with fold down
crank handle on sill.• Hinge arms are [steel] [stainless steel].• Corrosion-resistant fasteners of PVC-compatible material.• Hardware finish [White] [Almond] [Bright Brass] [Satin Nickel] [Oil-Rubbed
Bronze].
Screens• Standard Screen
Black vinyl coated 18 / 14 mesh fiberglass screen cloth complying with ASTM D 3656 and SMA 1201.
Set in aluminum extruded frame and fitted to interior of window. Insect screen frame finish is baked enamel, color to match interior.
-or-• InView™ Screens
Vinyl-coated 18/18 mesh fiberglass screen cloth complying with SMA 1201, set in aluminum extruded frame fitted to inside of window, supplied complete with all necessary hardware.
Insect screen frame finish is baked enamel, color to match interior.
Optional ProductsGrilles • Grilles-Between-the-Glass
Insulating glass contains [3/4"] [1"] contoured profile aluminum grilles permanently installed between two panes of glass.
Patterns are [Traditional] [9-Lite Prairie] [Top Row] [Custom–Equally Divided].
Interior grille color matches interior frame. Exterior grille color [3/4" Grille is [White] [Almond 4] [Brown] [Black]
[Brick Red] [Hartford Green] [Morning Sky Gray] [Poplar White] [Portobello] [Tan] [Fossil]] [1" Grille is [White] [Almond 4] [Brown]].
Available on units glazed with dual-pane and triple-pane insulated glass.
• Simulated-Divided-Light grilles without spacer 7/8" Grilles permanently bonded to the interior and exterior of glass. Patterns are [Traditional] [9-Lite Prairie] [Top Row] [Custom – Equally
Divided]. Grilles match color of interior and exterior frame. Available only on units glazed with dual-pane insulated glass.
Hardware• Optional limited opening hardware available for vent units in stainless
steel; nominal 3" opening.• Optional window opening control device available for field installation.
Device allows window to open less than 4” with normal operation, with a release mechanism that allows the sash to open completely. Complies with ASTM F2090-17.
Detailed Product Description
Rev. 05/22/2020
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-17
350 Series Casement
SILLS
HEADH
[114
]4
1/2"
OAW
JAMBJJAMBJ
[114]4 1/2" OAW
Scale 3" = 1' 0"
All dimensions are approximate.
Optional Foam Insulation
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-18
350 Series Casement
[11]7/16"
[103]4 1/16"
[89]
3 1/
2"
[17]5/8"
[98]3 7/8"
[89]
3 1/
2"
[32]
1 1/
4"
[114]4 1/2" OAW
[32]
1 1/
4"
[89]
3 1/
2"
[114]4 1/2" OAW
[32]
1 1/
4"
[16]
5/8"
[89]
3 1/
2"[8
9]3
1/2"
[83]3 1/4" OAW
[32]
1 1/
4"
[57]
2 1/
4"
[32]
1 1/
4"[4
4]1
3/4"[1
9]3/
4"[8
9]3
1/2"
[37]1 7/16"
[78]3 1/16"
[32]
1 1/
4"
[44]
1 3/
4"[8
9]3
1/2"
[37]1 7/16"
[78]3 1/16"
[89]
3 1/
2"
[32]
1 1/
4"
[114]4 1/2" OAW
GLAZING OPTIONS
PANE IG1 1/4" TRIPLE-
1" IG
5/8" INTEGRAL FLANGEBLOCK FRAME with
with J-CHANNELNAIL FIN
NAIL FINSTANDARD
FLUSH FLANGEDOUBLE WALL
BLOCK FRAMESTANDARD POCKET REPLACEMENT
Scale 3" = 1' 0"
All dimensions are approximate.
Additional Glazing Options
Unit Sections - Frame Types
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-19
350 Series Casement
[38]1 1/2"
Optional Factory Applied Wood Jamb Extensions
[89]3 1/2"
[16]
5/8"
FRAME WIDTH
LJ
HINGE JAMBHJ LOCK JAMBLJ
[60]2 3/8"
[44]1 3/4"
[44]1 3/4"
[37]
1 7/
16"
[78]
3 1/
16"
[89]3 1/2"
[57]2 1/4"
[32]1 1/4"
[60]
2 3/
8"
[167]6 9/16"
[116]4 9/16"
[37]1 7/16"
[78]3 1/16"
[69]
2 3/
4"[2
0]3/
4"
FRA
ME
HE
IGH
T
[44]
1 3/
4"[8
9]3
1/2"
[114]4 1/2" OAW
S
HJ
H
SILLS
HEADH
Scale 3" = 1' 0"
All dimensions are approximate.
Unit Sections - Standard Nail Fin
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-20
350 Series Casement
SILLS
HEADHLJ
S
HJ
H
[20]
3/4"
[60]2 3/8"
[69]
2 3/
4"
FRA
ME
HE
IGH
T
[89]
3 1/
2"
[83]3 1/4" OAW
FRAME WIDTH
[69]2 3/4"
[20]3/4"
[89]3 1/2"
[83]
3 1/
4"
JAMBJ[6
0]2
3/8"
Scale 3" = 1' 0"
All dimensions are approximate.
Unit Sections - Block Pocket Replacement Frame
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-21
350 Series Casement
FRAME WIDTH
HINGE JAMBHJ LOCK JAMBLJ
[44]1 3/4"
[44]1 3/4"
[37]
1 7/
16"
[78]
3 1/
16"
[89]3 1/2"
[57]2 1/4"
[32]1 1/4"
[60]
2 3/
8"
LJHJ
M
S
H
[20]
3/4"
[89]
3 1/
2"[6
9]2
3/4"
[52]
2 1/
16"
[60]2 3/8"
SILLS
HEADH
[32]
1 1/
4"
[191
]7
1/2"
[76]3"
[89]
3 1/
2"
TOTA
L FR
AM
E H
EIG
HT
MULLIONHORIZONTALM
FRA
ME
HE
IGH
TFR
AM
E H
EIG
HT
FRA
ME
HE
IGH
TFR
AM
E H
EIG
HT
1/2"
[13]
[37]1 7/16"
[78]3 1/16"
[44]
1 3/
4"
[114]4 1/2" OAW
Scale 3" = 1' 0"
All dimensions are approximate.
See Installation and Performance section for mulling limitations.
Unit Sections - Typical Factory-Assembled Joining Mullions
Pella 2020 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.Pella.com V350-CM-22
350 Series Casement
[38]1 1/2"
Optional Factory Applied Wood Jamb Extensions
[89]3 1/2"
[16]
5/8"
[44]1 3/4"
[69]2 3/4"
[20]3/4"
[52]2 1/16"
[60]
2 3/
8"
HINGE JAMBHJLOCK JAMBLJ
FRAME WIDTHFRAME WIDTHFRAME WIDTH FRAME WIDTH1/2" [13]
[44]1 3/4"
TOTAL FRAME WIDTH
[32]1 1/4"
[191]7 1/2"
[76]3"
MULLIONVERTICALM
[37]
1 7/
16"
[78]
3 1/
16"
[89]3 1/2"
[60]2 3/8"
[167]6 9/16"
[116]4 9/16"
[37]1 7/16"
[78]3 1/16"
[69]
2 3/
4"[2
0]3/
4"
FRA
ME
HE
IGH
T
[44]
1 3/
4"[8
9]3
1/2"
[114]4 1/2" OAW
SILLS
HEADH
M
S
HJ
H
Scale 3" = 1' 0"
All dimensions are approximate.
See Installation and Performance section for mulling limitations.
Unit Sections - Typical Factory-Assembled Joining Mullions
Product Selection GuideSize and Performance DataSound Transmission Class and Outdoor-Indoor Transmission ClassFeatures and Options
Glazing Performance11/16" Insulating Glass with 3mm1" Insulating Glass with 5mmDual-Pane Tinted GlassNon-Impact LaminatedTriple-Pane Insulating Glass
Grille TypesSize TablesSpecial Size Frame DimensionsMiscellaneous FormulasDesign DataDetailed Product DescriptionsUnit SectionsFrame Types OverviewStandard Nail FinBlock FrameJoining Mullion