Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
www.huelsta.com
1/19Type list
SLEEPING
E
2Schlafen: LUNISE 1. 2019
Important notes: Generally speaking, you as a dealer/qualified fitter are responsible for the correct wall mounting of the units. That is why wall mounting should only be carried out by properly trained and qualified fitters. hülsta supplies materials for mounting units on walls for nearly all the units and which should be used for safety and for constructional reasons. The assembly materials supplied by hülsta (plugs, screws) are only suitable for fitting components on to concrete in firmness class C12/15.For other materials (please see separate materials table in the wall composition chapter) we provide you with an assembly mortar set as an extra order. Please note that this assembly mortar set is also only suitable for the materials listed in the materials table. If walls are made up of other materials (e.g. plastered or lighter wall materials), one should use another method of mounting better suited to the load on site. Please note that if the units are not mounted properly on the wall, there is a risk of the units falling down or tipping over – especially when alternative mounting materials acquired on site have been used.For the reasons stated above it is absolutely essential to enquire about the composition of any walls before signing any contracts.
Range introduction
LUNIS
Ancillary units• Consoles with flush fronts; in one height and two widths, console for pedestals• Pedestals in one height and two widths• Chests with drawers or doors, with flush fronts, high chests with drawers or with flap and drawers, wall
chests with drawers; in four widths• Dressing chest• Angled shelves, with optional lamps• Drawer frames of consoles and chests in standard grey version
WardrobesHinge-door wardrobes according to the endless assembly principle• Hinge-doors with shell handle, optionally in a different version to the hinge-doors• Hinge-doors with flush front, optionally with flush-front mirrors (at a surcharge)• With optional cornice profile and/or top LED lamp (12 V; 2.4 W)• Wardrobe interior carcase in standard white lacquer• Standard interior fittings: 2 fitted shelves. 1 clothes rod• Functional and high-quality interior wardrobe fittings (see “Wardrobe interior fittings” type list)
Quality features• Wardrobe doors with shell handles and spring hinges• All metal hinges• Visually unobtrusive 2.5 mm drilled holes for wardrobes• Centre partitions and end side-sections of wardrobes with special plinth adjustment• hülsta Push-to-open: Drawers and doors of ancillary units with hülsta Push-to-open• hülsta MagicClose: All wooden hinge-doors with door hinge cushioning device
Height reductions at intervals of 1.0 cm without surcharge
In combination with the hülsta Sleeping System, the beds guarantee highest sleeping comfort. With its high-grade quality spring base frames and mattresses, the hülsta Sleeping System provides the perfect prerequisites for relaxing sleep (see “Sleeping systems“ type list).
Contents Page
Range introduction, lists of versions 2-3
Special combinations 4-5
Hinge-door wardrobes 6-7
Bed system 8-13
Bed accessories 14-18
Ancillary units, dressing chest, angled shelves, Magic-Tronic, remote control 19-21
General information:
Switch options for lamps 23
Special-sized products, special articles 24-26
Usable bed inside height and space under bed 27
Important notes: quality of walls / assembly instruction 28
... for relaxing, dreaming and wonderful sleep
LUNIS is the bedroom range of your choice if you appreciate having a lot of choice when planning your new bedroom suite. The multitude of creative possibilities that LUNIS has to offer is just as unique as this place of refuge is itself. Classical combinations of slatted base frames and mattresses or Boxspring units, upholstered beds or bed surrounds in wood veneer - all the different bed versions, wardrobes and ancillary units mean that the visual design concept of LUNIS creates a convincing overall impression.
Beds• Beds with headboard in wood/lacquer version and in high-gloss version (only for headboard A) or with
upholstered headboard, bed surround in wood/lacquer, high-gloss or upholstered version or with Boxspring in upholstered version; in four widths and three lengths
• Beds in 2 different surface heights• Comprehensive bed accessories: different bedside lamps, headboard upholstery, headboard panels and
numerous accessories for headboard panels
34
Labelling in type list drawings / assembly notes for wall unitsThe majority of units have two wall mounting points (= number of base plates), if these are to be fitted as wall units. This is not expli-citly mentioned in the type list. If a different number of wall mounting points (= base plates) is required, this is marked in the drawings in the type list with numbers in black boxes. Please be sure to note here the information and notes in the “Wall composition” chapter!
Link to the assembly / user instruction movies
LUNIS
3Schlafen: LUNIS E 1. 2019
Lists of versions
Changing versions:The model nos. for the wardrobe exterior carcase, wardrobe front, shell handle and cornice profile must be stated separately as colour combinations are possible. If versions from different price groups are exchanged, the higher price group is always charged (exception: exchanging versions of shell handle). Wardrobe interior carcase in standard white lacquer version.
WardrobesWardrobe front
White lacquerHigh-gloss whiteNatural oakDark stained oakCore walnut
640860685692680
Wardrobe exterior carcase, cornice profile, shell handle
White lacquerNatural oakDark stained oakCore walnut
640685692680
IIIIIIIII
Model no.Model no.
IIIIIII
640860685692680
Beds
Changing versions:The model nos. for the bed headboard, headboard surround and application, the bed surround and leg A or the cover no. for the upholstered headboard, the upholstered bed surround or the Boxspring must be stated separately as colour combi-nations are possible. If versions from different price groups are exchanged, the higher price group is always charged (excep-tion: exchanging versions of headboard surround and application).
White lacquerHigh-gloss whiteNatural oakDark stained oakCore walnut
Profiled headboard A, bed surround, headboard panel, leg A (round)
IIIIIIIII
Model no.
hülsta cover collectionor
Upholstered headboard C, bed surround, Boxspring, headboard upholstery
Price group
Price group Price group
Changing versions:The model no. for the ancillary unit exterior carcase and front, the open compartment and frame of the open compartment of console, the pedestal carcase and front as well as the dressing chest carcase and front must be stated separately, as colour combinations are possible. When exchanging versions from different price groups, the higher price group is always charged. Ancillary unit interior carcase in standard white lacquer version.
Ancillary units, pedestals, dressing chest, angled shelvesCarcases, open compart-ment of console, angled shelves
White lacquerNatural oakDark stained oakCore walnut
640685692680
Fronts, frame of open compartment of console
640860685692680
Panel carcase with box drawer or flap, angled panel shelves, housing of bedside lamp
Panel carcase with box drawer or flap, angled panel shelves, housing of bed- side lamp
White lacquerSaffron lacquerPetrol lacquerPastel green lacquerNatural oakDark stained oakCore walnut
640655654653685692680
IIIIIIIIII
Model no. Price group
Beds with headboard A in wood/lacquer/high-gloss version or with upholstered headboard C, bed surround in wood/lacquer, high-gloss or upholstered version or with Boxspring in upholstered version.hülsta cover collection: see „hülsta cover collection“ type list.
White lacquerHigh-gloss whiteNatural oakDark stained oakCore walnut
Model no.
IIIIIII
Model no. Price group Price group
IIIIIIIII
4Schlafen: LUNISE 1. 2019
301
--
0383
-
303
--
0385
-
304
--
0385
-
5-door hinge-door wardrobe(centre door with right hinges) 252 cm wide
Important: Choose a bed with profiled headboard A and surround in wood/lacquer or high-gloss version (all bed sizes possible – please state type no.; see pages 10-11), two consoles (console types 5205 and 5207 are possible – please state type no.; see page 19) as well as one of the wardrobes listed below.
6-door hinge-door wardrobe302 cm wide
4-door hinge-door wardrobe202 cm wide
Surcharge for top LED lamp
1 lamp per unit
Surcharge for cornice profile
Surcharge for top LED lamp
1 lamp per unit
Surcharge for cornice profile
Surcharge for top LED lamp
1 lamp per unit
Surcharge for cornice profile
Special combinations
Special combinations consisting of bed unit (bed and 2 drawer consoles) and one wardrobe. The price of an entire special combination (bed unit and wardrobe) can be found in the boxes shaded grey!
Bed: Bed with profiled headboard A and bed surround in wood/lacquer or high-gloss version Consoles: Consoles with 2 drawers, optionally 51.2 or 70.0 cm wideWardrobe: Wardrobe with hinge-doors; height reductions of hinge-door wardrobes at intervals of 1 cm without surcharge.
Please also note the mattresses and base frames in the “Sleeping systems” type list!
Price gr.III
Bed with profiled headboard A and bed surround frame in wood/ lacquer or high-gloss version and two drawer consoles
Important note:Bed also available optionally with a different headboard, with bed surround in upholstered version, with Boxspring, in surface height 2, with other legs or with consoles with open compartment (at a surcharge).See here the following page!
A8406
--
A8416
--
A8436
--
Special-sized products for special combinations are possible! Pricing: special combination + 15%
plus all the required special-sized products (see „Special-sized products“)!
Please note: Height reductions of wardrobes remain free of charge!
LUNIS
5Schlafen: LUNIS E 1. 2019
This luminaire contains built-in LED lamps of the energy classes A++ to A. The lamps cannot be changed in the luminaire. 12 V; 2.4 W
14 / 22,1 * cm
3002
-
2004
-
2004
-
2004
-
Surcharge for mirrorEach wardrobe door can be fitted with an optional flush-front mirror which is charged extra.
-
Surcharge for mirror per hinge-door
Additional fittings for beds
Additional fittings for special combinations / surcharges / lampsAdditional fittings for wardrobes
Bed headboardStandard version: profiled headboard A in wood/lacquer or high-gloss version
Upholstered head-board C with cover in
price gr. I
Surcharge for upholstered head-
board C with cover in price gr. III
Surcharge for upholstered head-
board C with cover in price gr. II
Surface heightsStandard version: surface height 1 (as in illustration 1)
Bed surroundStandard version: wood/lacquer or high-gloss version
Surcharges for bed surround in uphols-
tered version
Surcharge for bed sur-round in upholstered version with cover in
price group I
Surcharge for bed sur-round in upholstered version with cover in
price group II
Surcharge for bed sur-round in upholstered version with cover in
price group III
Illustr. 2Illustr. 1
Alternative bed legs
Surcharge for surface height 2(as in illustration 2)
Surcharges for Boxspring in uphols-
tered version
Surcharge for Box-spring in upholstered version with cover in
price group I
Surcharge for Box-spring in upholstered version with cover in
price group II
Surcharge for Box-spring in upholstered version with cover in
price group III
3010
-
3020
-
Surcharge for leg A(as in illustration 1)
Surcharge for leg B(as in illustration 2)
2002
-
2002
-
2002
without surcharge
Additional fittings for consoles
Rear surface treated headboardThe upholstered headboard can be given an optional rear side surface treatment (against a surcharge). So the bed can be placed anywhere in the room.
2001
-
Surcharge for 70.0 cm wide console with open compartment (as in illustration 2);
surcharge per console:
Illustr. 2Illustr. 1
2003 2003 2003- - -
ConsolesStandard version: with 2 drawers, 51.2 or 70.0 cm wide (as in illustration 1)
Maximum usable bed inside height (when support slats in bottom position)
* Surface height: see here the information on page 14!
=
=
Top LED lamp
1602 -
1603 -
Remote control
Surcharge for extra transmitter type
Surcharge for extra receiver type
Surcharge for remote control unit(transmitter + receiver) type
-1601
=
=
Surcharge for each additional lamp type 369 -15
,9 /
15,0
cm
16,5
/ 17
,2 c
m
16,5
/ 17
,2 c
m
24,0
/ 22
,0 c
m
Illustr. 2Illustr. 1
6Schlafen: LUNISE 1. 2019
369 -
This luminaire contains built-in LED lamps of the energy classes A++ to A. The lamps cannot be changed in the luminaire. 12 V; 2.4 W
=
=
Top LED lamp
1602 -
1603 -
Remote control
Surcharge for extra transmitter type
Surcharge for extra receiver type
Surcharge for remote control unit(transmitter + receiver) type
-1601
=
=
61.4 cm
see page 7Widths
Depths
229.6 cm
Dimensions
Height reductions at intervals of 1.0 cm without surcharge
Heights incl. plinth
74.2 cm
234.6 cm
with LED top lamp
without cor-nice profile
with cornice profile
with cornice profile and top
LED lamp
231.0 cm 235.4 cm
61.5 cm 68.7 cm
61,4
242
61,4
202
61,4
302
Hinge-door wardrobesNotes on planning hinge-door wardrobes according to the endless assembly principle
Hinge-door wardrobes can be planned endlessly and combined with one another. Due to the various element widths one can create many total wardrobe widths. In this way the available floor space can be exploited to the full. For each wardrobe combination, the first element on the left is conside-red to be the basic unit, incorporating both outer side-sections. One can only include one basic unit in each combination. When adding on extension units, the right-hand side-section of the basic unit is employed as the end side-section of the complete combination. In the case of single-door hinge-door units one can choose between left- and right-hand hinges. The graphics shown below give you an excerpt from our wardrobe assortment.
Standard interior fittings per unit: 2 fitted shelves, 1 clothes rod. All interior surfaces are in white lacquer.
Examples of wardrobesHinge-door wardrobe Hinge-door wardrobe
Hinge-door wardrobe
• Hinge-door wardrobes can be planned endlessly and combined with one another• Cornice profile, flush-front mirror fronts and lamps at a surcharge• Unit outside widths: 42, 52, 82, 102 cm (basic units) 40, 50, 80, 100 cm (extension units)• Unit inside widths: 38, 48, 78, 98 cm• Outside depth: 61.4 cm• Inside depth: 56 cm• Door opening angle: approx. 94°
• Hinge-door wardrobes can be planned endlessly and combined with one another• Cornice profile, flush-front mirror fronts and lamps at a surcharge• Unit outside widths: 42, 52, 82, 102 cm (basic units) 40, 50, 80, 100 cm (extension units)• Unit inside widths: 38, 48, 78, 98 cm• Outside depth: 61.4 cm• Inside depth: 56 cm• Door opening angle: approx. 94°
• Hinge-door wardrobes can be planned endlessly and combined with one another• Cornice profile, flush-front mirror fronts and lamps at a surcharge• Unit outside widths: 42, 52, 82, 102 cm (basic units) 40, 50, 80, 100 cm (extension units)• Unit inside widths: 38, 48, 78, 98 cm• Outside depth: 61.4 cm• Inside depth: 56 cm• Door opening angle: approx. 94°
LampsAll hinge-door wardrobes are available with top LED lamps. One top LED lamp is fitted standard above each element – 1 or 2 door – 12 V; 2.4 W. If required, a top LED lamp can be fitted centrally above each door. Please include a sketch in all cases.Switching is done by an external footswitch. A remote control unit is also available as an alternative, which is charged extra. The remote control unit incorporates one transmitter and one receiver which operate all the LED lamps. The footswitch is omitted when the remote control unit is employed.
Please note: When including the cornice profile, please note that the distance to the ceiling must be at least 2.0 cm.
Surcharge for each additional lamp type
LUNIS
7Schlafen: LUNIS E 1. 2019 L/R = Door hinge left/right
Single-door unit, left or right, 42 cm wide
Single-door unit, left or right, 52 cm wide
Twin-door unit, 82 cm wide
Twin-door unit, 102 cm wide
Single-door unit, left or right, 40 cm wide
Single-door unit, left or right, 50 cm wide
Twin-door unit, 80 cm wide
Twin-door unit, 100 cm wide
Extension units with 1 centre partition (2 cm thick)
For each project please remember to leave a 2.0 cm gap to the ceiling and at the side for assembly!
Height: 229.6 cm (height with cornice profile and/or top LED lamp: see table on page 6 top right; height reductions in intervals of 1.0 cm without surcharge)Width: see tableDepth: 61.4 cm (depth with cornice profile and/or top LED lamp: see table on page 6 top right)
Interior fittings per unit: 2 fitted shelves, 1 clothes rod;interior fittings always in white lacquer.
All hinge-doors with shell handle, optionally in a different version to the hinge-doors (without surcharge).
Basic units with 2 outer side-sections (each 2 cm thick)
For each wardrobe combination, the first element on the left is considered to be the basic unit, incorporating both outer side-sections. One can only include one basic unit in each combination. When adding on extension units, the right-hand side-section is employed as the end side-section.
Please also note the functional and high-quality wardrobe interior fittings in the „Wardrobe interior fittings“ type list as well as the special articles and possible special-sized products.
Surcharge for top LED lamp
1 lamp per unit
Price gr.III
Price gr.III
Price gr.III
Price gr.III
Price gr.III
Price gr.III
Price gr.III
Price gr.III
Notes on energy efficiency class: see page 6!
Doors with flush front
Surcharge for cornice profile
61,4
61,4
61,4
61,4
61,4
L
61,4
L
61,4
L
61,4
L380
-
380
-
380
-
380
-
Please mark exactly in the front sketch or state in the order (from the left) which hinge-doors are to be fitted with a mirror.
Surcharge for mirror per hinge-door:
-
382
-
382
-
382
-
382
-
A02012 RA02011 L
--
3410
--
3420
--
A0202
--
3430
--
A202
--
3440
--
A00012 RA00011 L
--
3460
--
A0012 RA0011 L
--
3470
--
A0002
--
3480
--
A002
--
3490
--
A2012 RA2011 L
--
Hinge-door wardrobesSurcharge for mirrorEach wardrobe door can be fitted with an optional flush-front mirror which is char-ged extra.
8Schlafen: LUNISE 1. 2019
Example of planning and ordering
1 Bed with profiled headboard A and bed surround in wood/lacquer/high-gloss version, in surface height 1, 180 x 200 cm
2 Console with 2 drawers, 51.2 cm wide3 Angled shelf, 70.0 cm wide4 LED lamp for 70.0 cm wide angled shelf5 Angled shelf, 128.0 cm wide6 LED lamp for 128.0 cm wide angled shelf7 Swing-out LED bedside lamp (set of 2)
2
2
77
4
3
1
5
6
Example of planning and orderingType 827
2x Type 5205Type 570Type 5002Type 5100Type 5003Type 978
LUNIS
9Schlafen: LUNIS E 1. 2019
Example of planning and ordering
3
2
4
1
4
1 Bed with profiled headboard C and Boxspring in upholstered version, in surface height 1, 180 x 200 cm2 Console with 2 drawers and 1 open compartment left, 70 cm wide3 Console with 2 drawers and 1 open compartment right, 70 cm wide4 Surcharge for upholstered headboard with function
Example of planning and orderingType 6274Type 52071Type 52072Type 801
10Schlafen: LUNISE 1. 2019
Anti-slip mat2.5 mm high, 170 cm long, 67 cm wideBecause of the low usable inside bed height in standard surface height 1, we recommend including an extra anti-slip mat to avoid the mattress slipping on base frames and mattresses which are quite high ( > 10 cm).
Anti-slip mattype
Profiled headboard A in wood/lacquer/high-gloss version
-900
Bed system consisting of profiled headboard A in wood/lacquer or high-gloss version and bed surround in wood/lacquer, high-gloss or upholstered version on standard arched support in hovering look or with Boxspring in upholstered version
Beds with bed surround in wood/lacquer, high-gloss or upholstered versionBeds incl. support slats for base frames and mattresses• Adjustable in height by 3.2 cm upwards or 3.2 cm downwards and upwards (see here page 14)• Usable bed inside height: max. 14.0 / 22.1 cmorBeds with Boxspring (fixed, not adjustable)
Headboard surround and application (not available in high-gloss version), optionally in a different version to the head-board (no surcharge). Please state clearly in the order!
hülsta cover collection: see „hülsta cover collection“ type list.Please state all the versions clearly in the order!
Inside dims. Outside dims.*
* Note on outer sizes:
Outer length of beds with bed surround in wood/lacquer, high-gloss and upholstered version = inside length +16 cm (example: inside size 200 cm = > outer size 216 cm)
Outer length of beds with Boxspring = inside length +14 cm (example: inside size 200 cm = > outer size 214 cm)
Please also note the mattresses and base frames in the “Sleeping systems” type list!Bed system with profiled headboard A in wood/lacquer or high-gloss version
Note:All bed systems are available optionally in 2 different surface heights and/or with alternative legs at a surcharge, see page 14. Please state clearly in the order!
99,6
Headboard surroundHeadboard application
* Surface height: see here the information on page 14!
140 x 200160 x 200180 x 200200 x 200
140 x 210160 x 210180 x 210200 x 210
140 x 220160 x 220180 x 220200 x 220
158.2 x 216/214178.2 x 216/214198.2 x 216/214218.2 x 216/214
158.2 x 226/224178.2 x 226/224198.2 x 226/224218.2 x 226/224
158.2 x 236/234178.2 x 236/234198.2 x 236/234218.2 x 236/234
140 x 200160 x 200180 x 200200 x 200
140 x 210160 x 210180 x 210200 x 210
140 x 220160 x 220180 x 220200 x 220
158.2 x 216/214178.2 x 216/214198.2 x 216/214218.2 x 216/214
158.2 x 226/224178.2 x 226/224198.2 x 226/224218.2 x 226/224
158.2 x 236/234178.2 x 236/234198.2 x 236/234218.2 x 236/234
Profiled head-board A in price group I
Profiled head-board A in price group II
betw
een
15.0
an
d 24
.0 *
16,5
/ 17
,2 *
LUNIS
11Schlafen: LUNIS E 1. 2019
Bed surround in wood/lacquer/high-gloss version
Bed accessories: see pages 14-18!
Bed surround in wood/lacquer/high-gloss version
Please be sure to observe the notes on surface heights and alternative legs on page 14!
Bed surround in upholstered version
Please be sure to observe the notes on surface heights and alternative legs on page 14!
Maximum usable bed inside height (when support slats in bottom position)
Bed surround in upholstered version
Type no.
Boxspring in upholstered versionfixed, not adjustable
Please be sure to observe the notes on surface heights and alternative legs as well as the product features of
the Boxspring on page 14!
Boxspring in upholstered version
14 / 22,1 cm 14 / 22,1 cm
Type no.Cover price group
825826827828
- - - - - - - - - - - -
825826827828
- - - - - - - - - - - -
845846847848
- - - - - - - - - - - -
835836837838
- - - - - - - - - - - -
845846847848
- - - - - - - - - - - -
8254826482748284
- - - - - - - - - - - -
8354836483748384
- - - - - - - - - - - -
8454846484748484
- - - - - - - - - - - -
8254826482748284
- - - - - - - - - - - -
8354836483748384
- - - - - - - - - - - -
8454846484748484
- - - - - - - - - - - -
Type no.
Genuine leather
Genuine leather
Cover price groupPrice group
IIII II
835836837838
- - - - - - - - - - - -
825826827828
- - - - - - - -
835836837838
- - - - - - - -
845846847848
- - - - - - - -
Maximum usable bed inside height (when support slats in bottom position)
I II IIII II
825826827828
----
835836837838
----
845846847848
----
----
----
----
12Schlafen: LUNISE 1. 2019
---
99971
172 x 224/220192 x 224/220212 x 224/220232 x 224/220
172 x 234/230192 x 234/230212 x 234/230232 x 234/230
172 x 244/240192 x 244/240212 x 244/240232 x 244/240
* Surface height: see here the information on page 14!
Genuine leather
172 x 224/220192 x 224/220212 x 224/220232 x 224/220
172 x 234/230192 x 234/230212 x 234/230232 x 234/230
172 x 244/240192 x 244/240212 x 244/240232 x 244/240
172 x 224/220192 x 224/220212 x 224/220232 x 224/220
172 x 234/230192 x 234/230212 x 234/230232 x 234/230
172 x 244/240192 x 244/240212 x 244/240232 x 244/240
107,
8
betw
een
15.0
an
d 24
.0 *
16,5
/ 17
,2 *
Anti-slip mat2.5 mm high, 170 cm long, 67 cm wideBecause of the low usable inside bed height in standard surface height 1, we recommend including an extra anti-slip mat to avoid the mattress slipping on base frames and mattresses which are quite high ( > 10 cm).
Anti-slip mattype
Upholstered headboard C (fixed)Upholstered headboard C available optionally with function(at a surcharge, see page 15).
-900
Bed system consisting of upholstered headboard C (fixed) with bed surround in wood/lacquer, high-gloss or upholstered version on standard arched support in hovering look or with Boxspring in upholstered version
Beds with bed surround in wood/lacquer, high-gloss or upholstered versionBeds incl. support slats for base frames and mattresses• Adjustable in height by 3.2 cm upwards or 3.2 cm downwards and upwards (see here page 14)• Usable bed inside height: max. 14.0 / 22.1 cmorBeds with Boxspring (fixed, not adjustable)
hülsta cover collection: see „hülsta cover collection“ type list.Please state all the versions clearly in the order!
* Note on outer sizes:Outer length of beds with bed surround in wood/lacquer, high-gloss and upholstered version = inside length +24 cm (example: inside size 200 cm = > outer size 224 cm)
Outer length of beds with Boxspring = inside length +20 cm (example: inside size 200 cm = > outer size 220 cm)
Bed system with upholstered headboard C
Note:All bed systems are available optionally in 2 different surface heights and/or with alternative legs at a surcharge, see page 14. Please state clearly in the order!
140 x 200160 x 200180 x 200200 x 200
Upholstered headboard in cover price group I
Upholstered headboard in cover price group II
Upholstered headboard in cover price group III
140 x 200160 x 200180 x 200200 x 200
140 x 210160 x 210180 x 210200 x 210
140 x 220160 x 220180 x 220200 x 220
140 x 220160 x 220180 x 220200 x 220
140 x 210160 x 210180 x 210200 x 210
140 x 200160 x 200180 x 200200 x 200
140 x 220160 x 220180 x 220200 x 220
140 x 210160 x 210180 x 210200 x 210
Please also note the mattresses and base frames in the “Sleeping systems” type list!
Rear surface treated headboardThe upholstered headboard can be given an optional rear side surface treatment (against a surcharge). So the bed can be placed anywhere in the room.
type
Surcharge in price group ISurcharge in price group IISurcharge in price group III
Please be sure to state in the order!
Inside dims. Outside dims.*
LUNIS
13Schlafen: LUNIS E 1. 2019
----
625626627628
----
635636637638
----
645646647648
----
625626627628
----
635636637638
----
645646647648
----
625626627628
----
635636637638
----
645646647648
14 / 22,1 cm 14 / 22,1 cm
Genuine leather
Genuine leather
IIII II I II IIII II
Bed surround in wood/lacquer/high-gloss version
Bed accessories: see pages 14-18!
Bed surround in wood/lacquer/high-gloss version
Please be sure to observe the notes on surface heights and alternative legs on page 14!
Bed surround in upholstered version
Please be sure to observe the notes on surface heights and alternative legs on page 14!
Bed surround in upholstered version
Boxspring in upholstered versionfixed, not adjustable
Please be sure to observe the notes on surface heights and alternative legs as well as the product features of
the Boxspring on page 14!
Boxspring in upholstered version
Cover price group Cover price group
Maximum usable bed inside height (when support slats in bottom position)
Maximum usable bed inside height (when support slats in bottom position)
Type no.Price group
Type no. Type no.
625626627628
- - - - - - - -
635636637638
- - - - - - - -
645646647648
- - - - - - - -
625626627628
- - - - - - - -
635636637638
- - - - - - - -
645646647648
- - - - - - - -
625626627628
- - - - - - - -
635636637638
- - - - - - - -
645646647648
- - - - - - - -
----
6254626462746284
----
6354636463746384
----
6454646464746484
----
6254626462746284
----
6354636463746384
----
6454646464746484
----
6254626462746284
----
6354636463746384
----
6454646464746484
14Schlafen: LUNISE 1. 2019
Two different surface heightsAll beds are available in two different surface heights, optionally:
with 15.9/15.0 cm high bed sides = surface height 1 (standard height) orwith 24.0/22.0 cm high bed sides = surface height 2 = Type
If surface height 2 is required (at a surcharge), please state clearly in the order!
with surface height 1:Support slats adjustable by 3.2 cm upwards,usable inside bed height: max. 14.0 cm
with surface height 2:Support slats adjustable by 3.2 cm downwards and upwards,usable inside bed height: max. 22.1 cm
Alternative bed legsThe beds with bed surround in wood/lacquer, high-gloss, or upholstered version stand on a standard arched support in hovering look, the beds with a Boxspring in upholste-red version are on round black standard legs.All beds are available optionally with alternative legs at a surcharge.Please state clearly in the order!
Surcharge for leg A
Standard leg for beds with bed surround in wood/lac-quer, high-gloss or uphols-tered version: on arched support in hovering look
3010
-
3020
-
-3002
Product information BoxspringBox fixed, not adjustable, with upholstered mattress with 7-zone, flat cylinder pocket spring core in a cover of furniture fabric (cover not removable/washable; surface with almost invisible anti-slip feature).
• Height: approx. 16 cm; firmness level: medium; weight approx. 28 kg (100 x 200 cm)• Good zone elasticity• Good body and spine support• Good moisture dispersion• Elastic 7-zone, flat spring core with multiple-sealed cylinder springs, sewn into pockets; 350 springs/m²; core height: ca. 5 cm
Surface height 1 (standard height)
15,9
cm
17,2
cm
24,0
cm
17,2
cm
Surface height 2
15,0
cm
16,5
cm
22,0
cm
16,5
cm
Standard leg for beds with Boxspring in uphols-tered version: on round black standard legs
Two different surface heights, alternative leg versions
Bed with bed surround
Bed with bed surround
Bed with Boxspring
Bed with Boxspring
Surcharge for leg B
Bed accessories
Product information Boxspring
Leg Around leg, different versions, please state the required version clearly in the order!
Leg Bsquare leg, optionally in high-gloss chrome or matt chrome, please state the required version clearly in the order!
LUNIS
15Schlafen: LUNIS E 1. 2019
This luminaire contains built-in LED lamps of the energy classes A++ to A. The lamps cannot be changed in the luminaire. 12 V
Genuine leather
Set of 2Swing-out LED bedside reading lamp (set of 2) for all bed headboards aluminium colour; for fitting on headboard (left and right). Fitting on upholstered headboard with function is not possible.
978
-
894
-
Ambience lamp for headboard of bed with inside width of:
140 cm 160 cm 180 cm 200 cm
8914
-
8916
-
8918
-
8920
-
Upholstered headboard with functionThe upholstered headboard is available optionally with a function. The top corners can be adjusted forwards to guarantee side support (e.g. for reading in bed).
Surcharge for upholstered head-
board with function
for bed inside width:
140 cm160 cm180 cm200 cm
Headboard upholstery with cover in price gr. I
Headboard upholstery with cover in price gr. II
Headboard upholstery with cover in price gr. III
Headboard upholstery for profiled headboard Aelliptical, 14.0 cm high, max. 5.4 cm thick; is fitted in the headboard application of headboard A.Later fitting is not possible.hülsta cover collection: see „hülsta cover collection“ type list.Please state the required version clearly in the order!
801
-
----
7014701670187020
----
7014701670187020
----
7014701670187020
Upholstered headboard with function
Bed accessories
Headboard upholstery for profiled headboard A
Bed lamps
LED bedside lamp (pair)with motion sensor for switching on and off (no time interval)
Ambience lamp for bed headboards can be dimmed; switch on headboard. Fitting on upholstered headboard with function, later fitting or including lamps in combination with headboard panels is not possible.
3 W per metre length
3.0 W
1.8 W
16Schlafen: LUNISE 1. 2019
This luminaire contains built-in LED lamps of the energy classes A++ to A. The lamps cannot be changed in the luminaire. 12 V
Headboard panel protruding left and right by 73.5 cm(for 76.8 cm wide pedestals)
Ambience lamp for headboard panel protruding left and right by 73.5 cm
Ambience lamp for headboard panel protruding left and right by 99.0 cm
Ambience lamp for headboard panelscan be dimmed; switch in panel (left and right); position of switch:36.0 cm from top rim and 61.0 or 79.5 cm (for 73.5 or 99.0 cm protruding headboard panels) from outer rim of headboard panel
Neither a combination with ambience lamps for bed headboards nor later assembly is possible.
979
-
296 cm316 cm336 cm356 cm
347 cm367 cm387 cm407 cm
min. 296.0 to max. 407.0
73.5 / 99.0 (outer rim of headboard panel to outer side of bed)
85140851608518085200
- - - - - - - -
87140871608718087200
- - - - - - - -
Bed accessories
Headboard panel
140 cm160 cm180 cm200 cm
Lamps for headboard panels
140 cm160 cm180 cm200 cm
Headboard panel protruding left and right by 99.0 cm(for 102.4 cm wide pedestals)
296 cm316 cm336 cm356 cm
347 cm367 cm387 cm407 cm
for bed inside width:
for bed inside width:
Type no.
Type no.
Type no.
Type no.
Price group I Price group II
Price group I Price group II
Set of 2
Headboard panel (standard split in the middle)101.2 cm high, 5.1 cm deep incl. wall mounting bracket; for wall assembly 1.8 cm above floor
All beds can be fitted in front of optional headboard panels. The headboard panels can be enhanced with a comprehensive range of accessories (see below and following pages).
The headboard panels must only be fitted on absolutely solid walls. Light masonry is not suitable for this purpose.Please be sure to note here the information and notes in the “Wall composition” chapter!
Swing-out LED panel reading lamp (set of 2)Housing of lamp in different versions; for fitting on headboard panel (left and right). Position of lamp (top rim of lamp): 9.0 cm from top rim and 55.0 or 77.0 cm (for 73.5 or 99.0 cm protruding headboard panels) from outer rim of headboard panel. Please state the required version clearly in the order!Later fitting is not possible.
3 W per metre length
1.2 W
----
8514851685188520
----
8714871687188720
Total width:
Total width:
for headboard panel width:
for headboard panel width:
3 W per metre length
9
55/77
36
61/79,5
LUNIS
17Schlafen: LUNIS E 1. 2019
--
50512
--
50768
6,4
46,6
73,5
Fitting position of 51.2 cm wide wall consoles Fitting position of 70.0 cm wide wall consoles
6,4
46,6
99,0
Electric socket for headboard panelsPosition of electric socket (centre of socket): 25.6 cm from bottom rim and 61.6 cm or 82.6 cm (for 73.5 or 99.0 cm protruding headboard panels) from outer rim of headboard panel
Later fitting is not possible.
61,6/82,6
25,6
06
-
99,0
54,3
6,419,2
54,3
99,0
Wall consoles for headboard panels14.7 cm high;44.8 cm deep
See below for fitting positions of wall consoles!
Max. load: 10 kg
6,4
54,3
73,5
Fitting positions of wall consoles
Please state the required fitting position clearly in the order!
70.0 cm wide wall consoles are not possible with the 73.5 cm protruding headboard panel.
19,2
99,0
46,6
Accessories for headboard panels
Electric socket for headboard panels
Wall consoles for headboard panels1 drawer 1 drawer
51.2 cm wide 70.0 cm wide
Height position 1 for 73.5 cm protruding headboard panels
Height position 1 for 99.0 cm protruding headboard panels
Height position 2 for 73.5 cm protruding headboard panels
Height position 2 for 99.0 cm protruding headboard panels
Height position 1 for 99.0 cm protruding headboard panels
Height position 2 for 99.0 cm protruding headboard panels
Price gr.III
18Schlafen: LUNISE 1. 2019
Position of 70.0 cm wide angled shelvesPosition of 38.4 cm wide angled shelves Position of 51.2 cm wide angled shelves
Panel carcases with box drawer or flap
Position of panel carcase with box drawer:Can be fitted anywhere in height and width (up to max. 64 cm from outer rim of head-board panels)
Position of panel carcase with flap:Panel carcase can be fitted anywhere on headboard panel (up to max. 64 cm from outer rim of headboard panels)
5128
--
5192
--
51.2 cm wide38.4 cm wide 70.0 cm wide
Angled shelves for head-board panels9.8 cm high14.0 cm deep
See below for positions of angled shelves!
Max. load: 5 kg
6,4
45,8*
73,5 / 99,0
6,4
45,8*
73,5 / 99,0
6,4
45,8*
99,0
6,4
30,8*
73,5 / 99,0
6,4
30,8*
73,5 / 99,0
6,4
30,8*
99,0
Positions of angled shelvesfor 73.5 and 99.0 cm protru-ding headboard panels
Please state the required position clearly in the order!
70.0 cm wide angled shelves can only be fitted in the 99.0 cm protruding headboard panel.
* Distance between top rim of headboard panel and bottom rim of angled shelf
can be fitted anywhere,
depending on headboard
panel width (max. 64 cm)
can be fitted anywhere
(as far as headboard)
Panel carcases for headboard panels
Angled shelves for headboard panels
Accessories for headboard panels
Panel carcase with 1 box drawer;H x W x D: 12.8 x 12.8 x 12.8 cm
Panel carcase with 1 flap;H x W x D: 19.2 x 19.2 x 15.1 cm
5030
--
--
--
5050 5070
Price gr.III
Price gr.III
LUNIS
19Schlafen: LUNIS E 1. 2019
Pedestalson 1.8 cm high plinth adjus-ters;16.5 cm high;57.6 cm deep
Consoleson 1.8 cm high plinth adjus-ters;46.6 cm high;44.8 cm deep
If consoles are fitted on pe-destals (see below), the plinth adjusters are omitted.
38.4 cm wide
LED inside drawer lampsConsoles with drawers can be fitted with optional LED inside drawer lamps (7.5 V, 1.0 W powered by standard AAA 1.5 V batteries included - rechargeable batteries not possible; with automatic on/off switch).
Please state exactly in your order which drawer is to be fitted with LED inside drawer lamps.
This type of luminaire is excepted from obligatory labelling in accordance with EU-VO 874/2012 guidelines (Reason: battery-operated and/or < 30 Lumen).
Surcharge for LED inside drawer lamps per drawer:
70.0 cm wide51.2 cm wide
Pedestal console38.4 cm high;44.8 cm deep
for placing on pedestals (see below)
5205
--
5207
--
5203
--
-
102.4 cm wide76.8 cm wide
51176
--
51110
--
505
-
Consoles
LED inside drawer lamps
Pedestals
70.0 cm wide
Ancillary units
2 drawers2 drawers 1 open compartment; 2 drawers LED lamp for open com-partmentLED lamp incl. footswitch; Magic-Tronic (see page 21) possible at a surcharge.
1 drawer; 1 inside drawer
1 drawer 1 drawer
This luminaire contains built-in LED lamps of the energy classes A++ to A. The lamps cannot be changed in the luminaire. 12 V
2.0 W
5207252071
--
as illustr.v. versa
Price gr.III
Price gr.III
Price gr.III
20Schlafen: LUNISE 1. 2019
5047
--
50412
--
52128
--
54128
--
54179
--
5605
--
5615
--
53128
--
53179
--
3
High chestson 1.8 cm high plinth adjus-ters;136.9 cm high;44.8 cm deep
Chestson 1.8 cm high plinth adjus-ters;91.4 cm high;44.8 cm deep
128.0 cm wide
128.0 cm wide76.8 cm wide
51.2 cm wide51.2 cm wide
Chests
Wall chests
High chests
128.0 cm wide
Ancillary units
4 drawers4 drawers 2 doors
4 drawers
6 drawers Top:1 flap
Bottom:3 drawers
179.2 cm wide128.0 cm wide
3 drawers 3 drawers
4 drawers
179.2 cm wide
Wall chests64.0 cm high;44.8 cm deep
Max. load 30 kg
The wall chests must only be fitted on absolutely solid walls. Light masonry is not suitable for this purpose. Please be sure to note here the information and notes in the “Wall composition” chapter!
Price gr.III
Price gr.III
Price gr.III
Price gr.III
Assembly notes for wall units:Please be sure to note here the information and notes in the “Wall composition” chapter!
34
LUNIS
21Schlafen: LUNIS E 1. 2019
This luminaire contains built-in LED lamps of the energy classes A++ to A. The lamps cannot be changed in the luminaire. 12 V
522
--
550
--
570
--
5100
--
-
5001
-
5002
-
5003
7617
-
Dressing cheston 1.5 cm high plinth adjus-ters;Total height incl. mirror:122.0 cm;47.0 cm deep
Substructure of metal, powder- coated white, panel and mirror rear side in white lacquer 132.0 cm wide
Angled shelves
Dressing chest1 drawer; panel with mirror and box drawer
Ancillary units
Angled shelves22.6 cm high22.6 cm deep
for fitting anywhere on walls
Max. load: 15 kg
LED lamps for angled shelves: see below! 128.0 cm wide70.0 cm wide51.2 cm wide
LED lamps for angled shelvesLED lamps for angled shelves
for 128.0 cm widthfor 70.0 cm widthfor 51.2 cm width
Magic-TronicThe lamps are normally operated by an external footswitch. As an alternative we can also provide a Magic-Tronic switch, which is charged extra. By “stroking” the outer or top side of the unit at the same level as the invisible integrated sensor it is possible to switch all the lamps on and off (“Stroking method”). As an alternative the position of the hidden sensor can also be marked with a small metal plate on the furniture unit (“Marking method”). Lamps with a maximum power of 200 W can be operated by a Magic-Tronic unit (230 V). The footswitch is omitted when a Magic-Tronic unit is included.
Please be sure to observe the information and notes regarding the assembly position!
LED lamps incl. footswitch. A Magic-Tronic or remote control unit is possible for operation (against a surcharge).
1 W per lamp
Price gr.III
Price gr.III
Price gr.III
The angled shelves may only be fitted on absolutely solid walls. Gypsum or other light masonry is not suitable for this purpose. Please be sure to note here the information and notes in the “Wall composition” chapter!
22Schlafen: LUNISE 1. 2019
Possible arrangements
LUNIS
23Schlafen: LUNIS E 1. 2019
Illustration 1: “Stroking method“
Illustration 2: “Marking method“
The lamps are normally operated by an external footswitch. As an alternative we can also provide a Magic-Tronic switch, which is charged extra. By “stroking” the outer or top side of the unit at the same level as the invisible integrated sensor it is possible to switch all the lamps on and off (“Stroking method”). As an alternative the position of the hidden sensor can also be marked with a small metal plate on the furniture unit (“Marking method”). Lamps with a maximum power of 200 W can be operated by a Magic-Tronic unit (230 V). The footswitch is omitted when a Magic-Tronic unit is included.
Standard position of Magic-Tronic for angled shelves:• for angled shelves of the METIS plus range: sensor is fitted 8 cm from the top rim and 8 cm from the left side in
the rear wall panel• for angled shelves of the LUNIS range: sensor is fitted 16 cm from the rear rim and 9.6 cm from the left side in the
shelf
Standard position of Magic-Tronic for consoles and chests:• for consoles and chests of the LUNIS range: sensor is fitted 16 cm from the rear rim in the cover shelf and 15.0 cm
at the side next to the bed• for consoles and chests of the MULTI-VARIS range: sensor is fitted 12 cm from the rear rim in the outer side next to
the bed and in approx. 7-15 cm from the top rim of the unit
Standard position of Magic-Tronic for MULTI-FORMA II wardrobes:• for hinge- and folding-door wardrobes of the MULTI-FORMA II range: sensor is fitted in the right passepartout in
approx. 130 cm height (Magic-Tronic is not possible for wardrobes without passepartout, in sliding-door wardrobes and in the room and niche system)
Alternative positions:If the Magic-Tronic sensor is to be fitted on the right in the rear wall panel or in the shelf of angled shelves, in the left passepartout of the wardrobe or at any position other than that stated as standard (e.g., if a unit is planned in a niche so that there is insufficient space to the right of the unit), please state this clearly in the order and mark the position in the sketch. If in doubt, please contact your hülsta customer advisor!
Switch options for lamps
Magic-Tronic
Magic-Tronic
Examples of use (schematic diagrams)Black point = Standard position of Magic-Tronic sensor for angled shelves (example 1), consoles and chests (example 2) or hinge- and folding-door wardrobes MULTI-FORMA II (example 3)
Notes:The black point in the drawings is the area where the Magic-Tronic sensor is invisibly integrated. If the surface is „stroked“ at this position, the lamps are switched on or off.
If you would like to mark the position of the Magic-Tronic sensor on the furniture, you can fit a small metal plate supplied separately at the corresponding position.
for hinge- and folding-door wardrobes of the MULTI-FORMA II range
Example 3
for angled shelves of the METIS plus range for angled shelves of the LUNIS range
Example 1
for consoles and chests of the LUNIS range for consoles and chests of the MULTI-VARIS range
Example 2
-
7617
24Schlafen: LUNISE 1. 2019
Special widths
Only applies to hinge- and folding-door wardrobes
• Single-door units, left or right hinges, can be reduced down to 25 cm width (apart from profiled doors).• Twin-door units can be reduced at both sides down to 50 cm total width (apart from profiled doors).• Interior fittings such as drawers and other fittings cannot be reduced in width.• For notes on width reductions on MULTI-FORMA II sliding-door wardrobes please see special-sized products
for MULTI-FORMA II!
Special heights, special widths, special depths
Notes on calculating sizes of sloping units
Rear sloping
Rear sloping is possible on all wardrobe units.
Measurements required:H 1 = Room heightH 2 = Height of slope (If a space is required between the wall and the wardrobe/unit,
please state the exact distance.)T 1 = Depth of slopeT 2 = Depth of slope
max. 46 cm
Special heights
• Hinge-, folding- and sliding-door wardrobes can be reduced in height at intervals of 1.0 cm.• Below eye-level we recommend fitting a top cover shelf made of panelling material.
Please state in order!• Special heights in stepped versions (not possible on sliding-door wardrobes) at a surcharge.
Surcharge per step:
Special depths
• Depth reductions are made on side sections, plinths, cornices and shelves.• Interior fittings such as drawers and other fittings cannot be reduced in depth.• A max. reduction of 30.0 cm is possible on hinge- and folding-door wardrobes.• A max. reduction of 9.0 cm is possible on profiled hinge-doors.• For sliding-door wardrobes, a max. reduction of 30.0 cm is possible (max. 18 cm in combination with the electrical opening
system for MULTI-FORMA II).• Please note that for technical production reasons not every special depth can be achieved:
2.5 cm standard reduction between 0 and 2.5 cm 5.0 cm standard reduction between 4.5 and 5.0 cm 27.5 cm standard reduction between 27.0 and 27.5 cm
Special-sized products
Side sloping
Sloping is only possible on single-door units. The door hinge (left or right) is positioned on the taller outer side of the unit.
Measurements required:H 1 = Room heightH 2 = Height of slope (If a space is required between the wall and the wardrobe/unit,
please state the exact distance.)B 1 = Width of slopeB 2 = Width of slopeG = Total widthS = Wardrobe width
Please note!• If the slope cuts across the position of a handle, the handle of this door only is positioned further
down in production.• As floors, ceilings and walls are never exactly straight, the exact room size must be measured using
a spirit level.• If a cornice is fitted, please state if this is to be continued in the sloping section.
-
00030
LUNIS
25Schlafen: LUNIS E 1. 2019
Special-sized products
LUNISWardrobes
Special heights:Hinge-door - WoodHinge-door - Mirror
Special widths:for single-door unit - Woodfor single-door unit - Mirrorfor twin-door unit - Woodfor twin-door unit - Mirror
When ordering extra fitted shelves and clothes rodsSize reduction surcharge per fitted shelfSize reduction surcharge per clothes rod
Special depths:Surcharge per unit
When ordering extra fitted shelvesSize reduction surcharge per fitted shelf
Side sloping:Surcharge per unit without cornice in the slopeSurcharge per unit with cornice in the slope
Side sloping is possible up to a minimum height of 88.0 cm.
Rear sloping:Surcharge per unit
Ancillary units
Special heights (drawers not possible in special height and not possible on high-gloss versions)CarcaseDoorChest of drawers in drawer raster
Special widths (not possible on high-gloss versions):CarcaseDoorDrawerPedestalHeadboard panel
When ordering extra fitted shelvesSize reduction surcharge per fitted shelf
Special widths are not possible on panel carcase and on angled shelves (for headboard panels).
Special depths (drawers not possible in special depth):Carcase
When ordering extra fitted shelvesSize reduction surcharge per fitted shelf
Beds
Bed in special length 190 cmUpholstered headboard in special heightBed with two footboards (all-round bed; only for beds with bed surround frame in wood/lacquer/ high-gloss version)
Special width and height are not possible on the profiled wood/lacquer headboard.
Special-sized products for special combinations:Pricing: special combination + 15% plus all the required special-sized products (see above)
More special products are possible. Please get in touch with your customer advisor.
without surcharge
000300031
----
000500051000600061
--
99919992
-0007
-9993
-9994
-99916
-99912
--
9990299903
-99902
-----
9991209991309991709993099925
-999141
-99932
-999341
--
9996499965
99967
without surchargewithout surcharge
26Schlafen: LUNISE 1. 2019
Special-sized products
Special articles
High-gloss care setPolish, polishing sponge and polishing cloth (incl. instructions) for protecting and maintaining the high-gloss surfaces
Edge veneerfor veneered/lacquered versions per m. length
165° hingesWardrobe doors can also be fitted with 165° hinges against a surcharge (only possible on plain, straight hinge-doors; impossible on fabric-covered doors and accent fronts). Please mark the doors clearly in the order!
Surcharge for 165° hinges per hinge-door:
Panels for side and top covering of fitted wardrobes (not possible for high- gloss versions; support construction and fitting materials must be acquired on site).
For veneered/lacquered versions (max. 268.0 cm long, max. 59.0 cm wide, 2.0 cm thick)Basis charge per order:+ price per m² - lacquer+ price per m² - veneerVeneer match with fronts can not be guaranteed.
Wardrobe doors are also available as separate units and are charged as follows:
For 1 hinge-door/folding-door wing: 50% of the concerning 1-door hinge-door extension unit
For 1 sliding-door including mechanism: 35% of the twin-door sliding-door wardrobe
For door superstructures, type 100 (max. 98 cm wide, only for assembly between wardrobes): 100% of twin-door hinge-door extension unit
9901 -990 -990 -
9902 -
180 -
36 -
Special colours; Note on „Blue Angel“ / Emissions label of DGM
Special coloursAll the hülsta lacquer colours are possible for nearly all the hülsta ranges. Availability and prices on request.
Note on „Blue Angel“ (RAL-UZ 38) and Emissions label of DGM (Class A)It is possible that the requirements of the „Blue Angel“ and the DGM Emissions Label can-not be met by some of the lacquer colours in price groups II and III (see here the different lacquer versions in the NURIA range), depending on the colour mix (surface ratio of these colours in the corresponding order). However, the legal requirements are definitely met in all cases!
Individual special-sized productsIf the special-sized product that you require is so unusual that it cannot be illustrated with the many special sized products that we already provide and charge for, then we will quote you the price using a HK unit type factor. In your order please state for us the relevant enquiry number and the HK unit type factor stated.
-HK
LUNIS
27Schlafen: LUNIS E 1. 2019
Note on usable bed inside height:The support slats of the hülsta beds are delivered in the centre position, i.e. they can be adjusted by 3.2 cm upwards and downwards (exception: for LUNIS beds in the standard surface height 1 only by 3.2 cm upwards). If the slats are set in the lowest position, the maximum usable bed inside height is achieved. In the case of some beds, the bed inside height is comparatively low. This means that mattresses in combination with base frames that are somewhat higher are not held so well by the bed side sections. Please note that the usable bed inside height of beds with height adjustable support slats is reduced when these are set higher.
This is how to calculate the individual height from the data supplied with the base frames:
Note on space under bed:The storage space underneath the base frame is calculated from the bed height minus the usable bed inside height.
Example bed: 42.2 cm - 18.0 cm = 24.2 cm.
Max. usable bed inside height:18.0 cm
approx. 12.5 cm for holding mattress
5.5 cm total height of base frame (example: hülstaflex basic B)
Example (for all beds): bed and hülstaflex basic B base frame (back and foot sections adjustable)
Usable bed inside height and space under bed
{
LUNIS bed in standard surface height 1 and hülstaflex basic B base frame (back and foot sections adjustable)
Max. usable bed inside height:14.0 cm
approx. 8.5 cm for holding mattress
5.5 cm total height of base frame (example: hülstaflex basic B)
{
28Schlafen: LUNISE 1. 2019
Labelling in type list drawings / assembly notes for wall unitsThe majority of units have two wall mounting points (= number of support boards), if these are to be fitted as wall units. This is not explicitly mentioned in the type list. If a diffe-rent number of wall mounting points (= support boards) is required, this is marked in the drawings in the type list with numbers in black boxes. Every support board requires four mounting screws.
One assembly mortar set is sufficient for up to a maximum of 3 support boards or 4 wall side-panels.
Important note: Depending on the composition of the wall (see wall types illustrated above), assembly must be carried out using the special assembly mortar set and a standard trade mastic tool which are the basic essentials for safe and clean workmanship.
Wall composition / assembly instructionImportant notes:The composition of walls must be ascertained before concluding a contract and be checked by a qualified fitter before assembly takes place.
Assembly may only be carried out by a qualified fitter under careful observation of the assembly instructions.
The plastic Rawl plugs with the type name SX 8 x 65 from the Fischer Company supplied by hülsta as a standard set are only suitable for concrete ≥ C12/15, if the wall composi-tion and compression strength corresponds to the table below. Under no circumstances must a unit be assembled on light masonry.
Furthermore, we provide a mounting set with assembly mortar from the Fischer Company for the types of walls listed below (see assembly mortar set below). Again, assembly must be carried out by a qualified fitter under careful observation of the wall composition and assembly instruction. The compression strength levels stated below must be met under all circumstances.
Assembly mortar set for up to a maximum of 3 support boards consisting of:
9x injection retaining sleeve9x screw-in sleeve1x injection cartridge2x static mixer1x assembly instructions
Please use the mounting screws from the standard set (supplied free of charge).
Mounting sets
Standard setThe standard set consists of 4 plastic Rawl plugs (SX 8 x 65) and 4 mounting screws and is sufficient for 1 support board. The standard sets are included in the packet of fittings to match the number of support boards.
34
= 3 support boards= 4 support boards, etc.
Building bricks Mz 12Compression strength ≥ 12 N/mm²
Limestone blocks KS 12Compression strength ≥ 12 N/mm²
Perforated sand lime bricks KSL12Compression strength ≥ 12 N/mm²
Vertically perforated bricks HLz 12Compression strength ≥ 12 N/mm²Bulk density ≥ 1.0 kg/dm³
Concrete C12/15Compression strength ≥ 15 N/mm²
Assembly mortar set only suitable for the materials stated below!Standard set (SX 8 x 65)
Solid blocks of light concrete V2Compression strength ≥ 2 N/mm²
Perforated blocks of light concrete Hbl 2Compression strength ≥ 2 N/mm²
Aerated concrete PP2Compression strength ≥ 2 N/mm²
Materials tablewith a description of which sets are to be used with the following types of walls:
Example of order:
• Add up number of support boards for all existing unit types
• Divide the sum by “3”
• Round up the result to a full number
= Number of assembly mortar sets required
Important notes
-
M2
A different and more suitable type of mounting must be chosen by a qualified fitter in all other cases. hülsta cannot accept any responsibility for the choice of any other types of mounting! Please note that if the units are not mounted properly on the wall, there is a risk of the units falling down or tipping over – especially when alternative mounting materials acquired on site have been used. Generally speaking, you as a dealer/qualified fitter are responsible for the correct wall mounting of the units.
LUNIS
29Schlafen: LUNIS E 1. 2019
Notes
Design and concept legally protected, subject to error and alterations to construction, colour and materials by way of technological progress.
Stand:
hülsta LUNIS
Your Hotline to hülsta
Lots to do? A customer wants his project finished and you haven’t got enough time? Or the project is so complex that it will take too much time?
This is exactly the kind of situation we created the hülsta Planning Service for. hülsta’s employees create the required project for you at short notice. Based on your information, we implement the project perfectly with all views and a complete order list ready for immediate forwarding to the customer.
The hülsta check list (available at https://hulsta.com/de/service/showroom/) makes it all really easy for you. You won’t forget anything with this list and the customer receives a project he will be thrilled about as quickly as possible.
Our Saturday hotline is available all day from 10.00 a.m. until 6.00 p.m.
Telephone: +49 (0) 2563 / 86-1800
On working days the hülsta Sales Department is available all day from 8.00 a.m. until 6.00 p.m.
hülsta Planning Service
Special wishes? Come to us!
We are open Saturdays for you, too!
E 1. 2019
Maximum individuality! – Maximal flexibility! – hülsta makes most of your special wishes possible.And if you do have a wish which is not quite so easy to implement, just give us a call or send us a mail or a fax. We have our own hülsta “Special Wishes Team” who are there to help you realise just these customer requests. These colleagues are professionals when it comes to special products. They plan and calculate the products possible for you and even develop an alternative suggestion if the idea should turn out to be technically impossible.
Here is an overview of the hülsta range of special wishes:• A lot of special products can be ordered simply via the type list• Special-sized products are planned simply and professionally• Competent colleagues advise you by phone, by fax and by mail• You will be sent alternative suggestions if the idea is technically impossible• Many special-sized products are available without a surcharge• Specially qualified carpenters and technicians implement your plans perfectly
Do you have any questions or require any alterations to your order confirmation?Do you have any questions on our products or your current order?Do you have any complaints about supplied goods or required replacement parts?Contact Telephone: +49 (0) 2563 / 86-1144 • email: [email protected]
Do you have any questions, suggestions or wishes for the hülsta Marketing team or the hülsta product seminars?Contact Telephone: +49 (0) 2563 / 86-1611 • email: [email protected]
hülsta Planning ServiceTel.: +49 (0) 2563 / 86-0
Fax: +49 (0) 2563 / 86-2666Mail: [email protected] from 8.00 a.m. until 6.00 p.m.
hülsta Special Wishes TeamTel.: +49 (0) 2563 / 86-0
Fax: +49 (0) 2563 / 86-1417Mail: [email protected]
hülsta-werke · Karl-Hüls-Straße 1 · D-48703 StadtlohnTel. +49 (0) 2563 / 86-0 · Fax +49 (0) 2563 / 86-1000
www.huelsta.com