Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
NEWNon-slip!The minimum size 1 in the series of NV type STUDROLLER system !
Non-slip!The minimum size 1 in the series of NV type STUDROLLER system !
SLIDE WAY NV type, NVT type, NYT type
One of the Smallest in the World ! !One of the Smallest in the World ! !
NV-NVT-NYT.indd aNV-NVT-NYT.indd a 2017/6/20 13:13:282017/6/20 13:13:28
NV type rail
end piece
R-retainer
STUDROLLER
table
stopper
adjustment screw
NV type rail
bed R-retainer
table
NV type rail
adjustment screw
stopper
W type railR-retainer
SLIDE WAY
The NB slide way NV type comprises precisely ground rails and R-retainers (made of resin) with built-in STUDROLLERs and precision rollers. The rails have been optimally designed so that the STUDROLLERs move smoothly, and the STUDROLLERs in the R-retainers enable slip-free operation between the raceway surface and suitable for the motion of up and down and very fast cycle, which is the weak fi eld for slide way products.
The STUDROLLER system is based on a new concept to provide complete prevention of roller cage slippage during operation. This system permits usage in all orientations and positions.
Non-slip! NV type STUDROLLER System (Rivet Roller Structure)
Suitable for Minute MotionBecause the frictional resistance is extremely small and there is only little difference between the static and dynamic frictional resistances, the NB slide way is well suited for minute motion, resulting in highly accurate linear movement.
Low-Speed StabilitySince the frictional resistance fl uctuation is small even under low-load conditions, stable motion is obtained at from low to high speeds.
High Rigidity and High Load CapacityCompared to the ball elements, the rollers provide a larger contact area and less elastic deformation, thus the NB slide way has high rigidity and high load capacity.With new NV rail design, the roller contact area is increased by 30 to 58% (Figure 1). The number of effective rollers is increased by narrowing the roller pitch. Thus, the NV type has the load rating that is 1.3 to 2.5 times that of the SV type.
Low NoiseThe slide way never produces recirculation noise nor rollercontact noise due to a use of roller cage, resulting in quiet motion.
All Stainless Steel Type AvailableThe anti-corrosion SVS/SVWS/NVS-RNS slide ways have all stainless steel components, making them ideal for use in clean room applications.
Figure 1 Roller Contact Profi le
SV typeNV type
Figure 2 Structure of NV type Figure 3 Structure of NVT type Figure 4 Structure of NYT type
※To the NV type, fastening plates are attached for the purpose of maintaining the center position of the R-retainer before assembly. Please see Installation Procedure on page 3 and remove the fastening plates before use.
STRUCTURE AND ADVANTAGES
1
NV-NVT-NYT.indd 1NV-NVT-NYT.indd 1 2017/6/20 13:13:302017/6/20 13:13:30
Figure 5 NV Type Parallelism Figure 6 NV Type Accuracy Measurement Method
Ultra precision grade is available from size 1 to size 9.
10
8
6
4
2
0
high
precision (P)
ultra precision (UP)
rail length (L) mm200 400 600 800 1000 1200
μm
para
llelis
m (
V o
r W)
WW
V V V
Y
Z Z
Y
L=( fTfW・CP)10/3・50 Lh= L・103
2・ℓS・n1・60
T
S
The accuracy of the NV type is represented as parallelism measured across the full length with a method shown in Figure 6. It is classifi ed as high (blank), precision (P), or ultra precision (UP). Special accuracies can also be accommodated. Please contact NB for details.
The motion accuracy of NVT and NYT type is measured by placing indicators at the center of the top and side surface of the table, as illustrated in Figure 7. It is expressed in terms of the indicator deviation when the table is moved the full stroke without any load.For accuracy, please see the dimension tables.
The life of the slide way and the slide table is calculated with the following equations:
The load rating of the NV, NVT and NYT type differs depending on the direction of the load.
TYPES
ACCURACY
RATED LIFE
LOAD RATING
Figure 7 NVT · NYT Type Accuracy Measurement Method
Life TimeRated Life
Table 1 Change of Load Rating Corresponding to Load Direction Figure 8 Direction of Load
L: rated life (km) fT: temperature coefficient fW: applied load coeffi cient C: basic dynamic load rating (N) P: applied load (N)
Lh: life time (hr) ℓS: stroke length (m)n1: number of cycles per minute (cpm)
1.0×C0.85×C0.7×C1.0×CO0.85×CO0.7×CO
※There may be a difference depending on the size. Please contact NB for details.Consideration has been given to holes for STUDROLLERs in the raceway surface in calculation of load ratings.
basic dynamic load rating
basic static load rating
normal vertical direction
horizontal direction
reverse vertical direction
normal vertical direction
horizontal direction
reverse vertical direction
horizontal direction
reverse vertical direction
normal vertical direction
2
SLIDE WAY
The NV slide way consists of a set of four rails, two R-retainers, and eight end pieces. It permits flexible design of the table which will best suit your application.The NVS-RNS type has all stainless steel components, which is suitable for anticorrosion, high temperature and vacuum requirements.
NV typeNVS-RNS type
P.5
The NVT type slide table incorporates the NV type slide way. The table and bed have been precision machined to provide a h igh degree of accuracy and the product can be used, without any need for troublesome accuracy or preload adjustments.In the NVTS type, the anti-corrosion NVS type slide way is sandwitched between an accurately machined aluminum table and bed.
NVT-NVTS type
P.11
The NYT/NYTS type is a thin, compact slide table, utilizing the studroller system. Either tapped or counterbore mounting type (D type) is available.The anti-corrosion type NYTS slide table is made of all stainless steel components except for R-retainer.
NYT-NYTS type
P.15P.17
NV-NVT-NYT.indd 2NV-NVT-NYT.indd 2 2017/6/20 13:13:312017/6/20 13:13:31
adjustment screws
dial indicators
R-retainer
R-retainer
R-retainer
adjustment screws
end piece
fastening plates
table
bed
×: Adjustment screws should not be tightened.
◯: Adjustment screws can be tightened.
g
f
e
d
c
b
a
adjustment side
① ④
② ③
MOUNTING
INSTALLATION PROCEDURE OF NV TYPE
Example
Accuracy of Mounting SurfaceTo maximize the performance of the NB slide way, it is recommended that the accuracy of the mounting surface to be equal to or greater than the degree of parallelism of the slide way.
Parallelism of surface 1 against surface APerpendicularity of surface 2 against surface AParallelism of surface 3 against surface BPerpendicularity of surface 4 against surface BParallelism of surface 2 against surface CParallelism of surface 4 against surface C
Figure 9 NV type
31.6
4 412
31.6
1.6 1.6
1.6
1.6
1.6
A
B
C
Figure 10 Accuracy of Mounting Surface
Figure 11 Installation MethodInstallation Procedure※Please read“Use and Handling Precautions”
before installation.
(1) Remove bur r s , sc ra tches , and dus t f rom the railmounting surface of the bed and the table, be careful to prevent contamination during assembly.
(2) Apply low-viscosity oil to the contact surfaces, and align the bed and the table. (Figure 11a)
(3) Set the reference surface onto the mounting surface with the rails fastened. Set the table in the center position, and tighten the adjustment screws lightly so that almost no gap remains. (Figure 11b)
(4) Keep the table in the center, tighten the rail mounting bolts lightly, loosen the end pieces of both ends, and remove the fastening plates. Following this, lightly retighten the end pieces.
(5) While maintaining the conditions of (4), gently move the assembly through its stroke to check if the maximum stroke is secured, and if there is no irregularity.
(6) Move the table to the center and tighten only the ad justment screws on the R- re ta iner w i th the recommended torque shown in Table 2. (Figure 11c)
(7) Gently move the table to one stroke end, and check that the table has surely come into contact with the external mechanical stopper. Following this, tighten the adjustment screws in the same manner as (6). (Figure 11d)
(8) Move the table to the opposite stroke end, and tighten in the same manner as (6). (Figure 11e)
(9) Fasten the mounting screws on rails 1, 2, and 3 by tightening with the recommended torque shown in Table 3. (Figure 11f)
(10) Set the dial indicators to the center of the table and to the side (reference surface) of the table. (Figure 11g)
(11) Perform the fi nal preload adjustment. While moving the table back and forth, repeat steps (6) to (8) until the dial indicators show a minimum deviation.
(12) Fasten rail 4 securely with the recommended torque. As for the adjustment screws, successively tighten the mounting screws on the R-retainer by moving the table.
(13) Recheck the motion accuracy while moving the table. (14) Tighten the end pieces fi nally.
3
NV-NVT-NYT.indd 3NV-NVT-NYT.indd 3 2017/6/20 13:13:312017/6/20 13:13:31
Table 2 Recommended Torque for Adjustment Screw
Table 3 Recommended Torque for Mounting screw Unit: N·m
part number
NV1
NV2
NV3
NV4
NV6
NV9
size
M2
M3
M4
M4
M5
M6
torque
0.008
0.012
0.05
0.08
0.20
0.40
Unit: N·m
M2
M3
M4
M5
M6
M8
0.4
1.4
3.2
6.6
11.2
27.6
(for steel alloy screw)
size torque
Figure 12 Special Mounting Screw
BT 3BT 4BT 6BT 9BT12
part number
S
B
d
L1L2
H
D
Table 4 Special Mounting Screw
M3M4M5M6M8
B
2.33.13.94.66.25
dmm
Dmm55.888.511.3
34568
Hmm
L1mm1215203040
5 7 81217
L2mm
Smm2.53456
NV 3NV 4NV 6NV 9NV12
applicable size
special mounting screw
SPECIAL MOUNTING SCREW BT TYPE
USE AND HANDLING PRECAUTIONS
In case of mounting slide way by screws from the counterbore side, threaded holes become the pilot holes. Thus, pilot hole's clearance will be less than a standard clearance hole for a screw. NB offers reduced shoulder screws for mounting SlideWay from bottom when larger screw clearance is required due to preload adjustment or inaccuracy of mating threaded holes. This special mounting screw made of alloy steel is stocked, and custom stainless steel version is available as a special order. Please contact NB for details.
Careful HandlingDropping the slide way causes the rolling elements to make dents in the raceway surface. This will prevent smooth motion and will also affect accuracy. Be sure to handle the product with care.The NV type is packaged as a set of rails and R-retainers. Do not separate or disassemble until assembly/installation is completed. Precision is not guaranteed if disassembled.
Fastening PlatesFor the NV type, fastening plates are attached at both end faces of the rails to maintain the R-retainer center position prior to assembly. The fastening plates are not required after the NV type is mounted to a table and bed, however, when removal of the NV type is necessary such as when it will be reassembled, be sure to return the R-retainer to the proper center position, secure the fastening plates with the end pieces, and then remove the NV type.
Specifi ed Allowable StrokeFor the NV type, exceeding the specified stroke (overstroke) shall cause the raceway surface of the rail to be damaged and the performance of the STUDROLLER to drastically deteriorate. Be sure to provide external mechanical stoppers.
AdjustmentUsing the product with insufficient accuracy of the mounting surface or before adjusting the preload will cause the motion accuracy of the product to drop and will have a negative influence upon product l i fe and accuracy. Make sure to assemble, install, and adjust the product with care.
Caution against Excess PreloadIt is essential to give preload on the Slide Way products in order to assure rigidity and accuracy.
However, excess preload causes damage on the raceways and roller cages/R-retainers.On installation, please follow the installation procedure and recommended torque on page 3.
Use as a SetThe accuracy of the rails has been matched within each set. Note that the accuracy will be affected when the rails of different sets are combined.
Allowable LoadThe allowable load is a load under which the sum of raceway in the contact area subject to the maximum contact stress is small enough to guarantee smooth rolling movement. When very smooth and highly accurate linear motion is required, make sure to use the product within the allowable load.
StopperEnd pieces are attached to each end of the slide way to prevent removal of the cage. Do not use them as a mechanical stopper.
Operating TemperatureThe NV type uses resin parts. Please use the product in environments that are lower than 80℃.
Dust PreventionDust and foreign particles affect the accuracy and lifetime of the slide way. The slide way used in a harsh environment should be protected with a cover.
LubricationThe slide way is prelubricated with lithium soap based grease No. 00 prior to shipment for immediate use. Make sure to relubricate with a similar type of grease periodically depending on the operating conditions. NB provides low dust generation greases for your linear system.
4
SLIDE WAY
NV-NVT-NYT.indd 4NV-NVT-NYT.indd 4 2017/6/20 13:13:312017/6/20 13:13:31
NVS 2 150 41Z UP--
NV TYPE-NV1/NV2/NV3-
part number structure
example
specifi cationNV : standardNVS : anti-corrosion
※Stainless steel rollers are used for anti-corrosion type.
number of rollers
size
rail length
NV2030- 5Z2045- 9Z2060-15Z2075-19Z2090-23Z2105-27Z2120-33Z2135-37Z2150-41Z2165-47Z2180-51Z
NV3050- 9Z3075-13Z3100-19Z3125-23Z3150-29Z3175-35Z3200-41Z3225-43Z
NVS2030- 5Z2045- 9Z2060-15Z2075-19Z2090-23Z2105-27Z2120-33Z2135-37Z2150-41Z2165-47Z2180-51Z
NVS3050- 9Z3075-13Z3100-19Z3125-23Z3150-29Z3175-35Z3200-41Z3225-43Z
stroke
STmm
18 25 30 40 50 65 70 80 90 95 100 25 48 60 83 90 103 113 150
number of rollersZ
L
mm
A
mm
roller diameterDmm
2
3
5 9 15 19 23 27 33 37 41 47 51 9 13 19 23 29 35 41 43
30456075901051201351501651805075100125150175200225
12
18
6
8
5.7
8.65
B
mm
C
mm
The basic static load rating is the value at the center of the stroke.
part number
anti-corrosionstandard
1.5 8.5 4 4.03
NV1020- 5Z1030- 7Z1040-11Z1050-15Z1060-19Z1070-23Z1080-27Z
NVS1020- 5Z 1030- 7Z 1040-11Z
1050-15Z1060-19Z1070-23Z1080-27Z
12232834404551
571115192327
20304050607080
accuracy gradeblank : highP : precisionUP : ultra precision
5
NV-NVT-NYT.indd 5NV-NVT-NYT.indd 5 2017/6/20 13:13:312017/6/20 13:13:31
(T)(T)
C
A*
G E
H
Fd
D
P
(N)(N)
L
M×P 0-0.1B
*High grade: -0.2 Precision grade (UP): A-0.1 Ultra Precision grade (UP): A0 0
-0.10
One set consists of 4 rails, 2 R-retainers, and 8 end pieces.
1N≒0.102kgf
dynamicCN
staticCoN
basic load rating
size
2030204520602075209021052120213521502165218030503075310031253150317532003225
g
334962749110312013214916117497140192245290337385434
allowable load
mass (one set)
FN
F
M3
M4
1×152×153×154×155×156×157×158×159×1510×1511×151×252×253×254×255×256×257×258×25
7.5
12.5
2.5
3.5
M×P
mm
N
mm
E
mm
d
mm
G
mm
H
mm
T
mm
2.55
3.3
4.4
6
2
3.1
1.2
2
1,3602,3303,9904,7405,4606,1606,8307,4908,1309,3709,9706,1508,44012,50014,40016,30019,80021,50023,200
1,5203,0506,1107,6309,16010,60012,20013,70015,20018,30019,8008,06012,10020,10024,20028,20036,30040,30044,300
5091,0102,0302,5403,0503,5604,070
M2
1×102×103×104×105×106×107×10
5 1.8 1.65 3 1.4 0.8
4,5805,0906,1106,6202,6804,0306,7208,0609,41012,10013,40014,700
7341,2501,7202,1602,5602,9603,330
8491,6902,5403,3904,2405,0905,940
2835668491,1301,4101,6901,980
9131822263135
1020103010401050106010701080
major dimensions
6
SLIDE WAY
NV-NVT-NYT.indd 6NV-NVT-NYT.indd 6 2017/6/20 13:13:312017/6/20 13:13:31
NV 6 200 19Z UP--
NV TYPE-NV4/NV6/NV9/NV12-
part number structure
The UP grade is not available for NV 12
NV4080- 9Z4120- 17Z4160- 23Z4200- 29Z4240- 37Z4280- 43Z
4
91723293743
11
NV6100- 9Z6150- 15Z6200- 19Z6250- 25Z6300- 31Z6350- 35Z6400- 39Z
NV9200- 13Z9300- 21Z9400- 29Z9500- 35Z
NV12300- 15Z12400- 21Z12500- 27Z12600- 31Z
NVS4080- 9Z4120- 17Z4160- 23Z4200- 29Z4240- 37Z4280- 43Z
STmm
6385135158180230275120170220300180230280380
---------------
ZL
mmDmm
6
9
12
91519253135391321293515212731
100150200250300350400200300400500300400500600
22
A
mm
31
44
58
15
22
28
B
mm
10.65
15.15
21.5
28.5
C
mm 60 75 105 130 143 170
80120160200240280
part number
anti-corrosionstandard
stroke number of rollers
roller diameter
The basic static load rating is the value at the center of the stroke.
example
specifi cationNV : standardNVS : anti-corrosion
※Stainless steel rollers are used for anti-corrosion type.
number of rollers
size
rail length
accuracy gradeblank : highP : precisionUP : ultra precision
7
NV-NVT-NYT.indd 7NV-NVT-NYT.indd 7 2017/6/20 13:13:312017/6/20 13:13:31
(T)(T)
C
A*
G E
H
Fd
D
P
(N)(N)
L
M×P 0-0.1B
*High grade: -0.2 Precision grade (UP): A-0.1 Ultra Precision grade (UP): A0 0
-0.10
One set consists of 4 rails, 2 R-retainers, and 8 end pieces.
20
25
50
50
N
mm
1N≒0.102kgf
CN
CoN
6100 6150 6200 6250 6300 6350 6400 9200 9300 9400 950012300124001250012600
g
6509701,3001,6201,9402,3602,7802,7204,0805,4406,7906,7709,04011,30013,560
FN
F
M6
M8
M10
d
mm
G
mm
H
mm
5.2
6.8
8.5
5.2
6.2
8.2
29,60050,90060,60069,80087,40095,800104,00096,100143,000186,000226,000228,000271,000352,000391,000
37,50075,10093,900112,000150,000169,000187,000128,000213,000298,000384,000317,000397,000555,000635,000
12,50025,00031,30037,50050,10056,30062,600
M5 4.3
9.5
10.5
13.5
8 4.2
T
mm
3
4
4
2
42,60071,10099,500128,000105,000132,000185,000211,000
12,10020,70028,50032,10039,00045,600
15,70031,50047,20055,10070,90086,600
5,25010,50015,70018,30023,60028,800
265400530660800930
408041204160420042404280
4.5
6
9
12
E
mm1×402×403×404×405×406×401×502×503×504×505×506×507×501×1002×1003×1004×1002×1003×1004×1005×100
M×P
mm
dynamic staticbasic load rating allowable
loadmass
(one set)major dimensions
size
8
SLIDE WAY
NV-NVT-NYT.indd 8NV-NVT-NYT.indd 8 2017/6/20 13:13:322017/6/20 13:13:32
NVS 4 200 27ZRNS P--
NVS-RNS TYPE-Special Environments Type-
part number structure
NVS 2030-RNS 7Z2045-RNS11Z2060-RNS13Z2075-RNS17Z2090-RNS21Z2105-RNS23Z2120-RNS27Z2135-RNS31Z2150-RNS33Z2165-RNS37Z2180-RNS43Z
NVS 3050-RNS 9Z3075-RNS13Z3100-RNS17Z3125-RNS21Z3150-RNS25Z3175-RNS29Z3200-RNS33Z3225-RNS35Z
NVS 4080-RNS 9Z4120-RNS17Z4160-RNS21Z4200-RNS27Z4240-RNS31Z4280-RNS37Z
※Some specification values are different from those of NV standard type. Please contact NB for details.
STmm152030405065708090951002038557085103113150586098115143170
ZL
mm
A
mmDmm
2
3
4
71113172123273133374391317212529333591721273137
3045607590105120135150165180507510012515017520022580120160200240280
12
18
22
6
8
11
5.7
8.65
10.65
1×152×153×154×155×156×157×158×159×1510×1511×151×252×253×254×255×256×257×258×251×402×403×404×405×406×40
7.5
12.5
20
2.5
3.5
4.5
B
mm
C
mm
M×P
mm
N
mm
E
mm
part number
stroke number of rollers
roller diameter
major dimensions
example
specifi cationNVS : anti-corrosion
size
rail length
accuracy gradeblank : highP : precisionUP : ultra precision
number of rollers
cage typeRNS : stainless steel cage stainless steel rollerRN : stainless steel cage standard roller
9
NV-NVT-NYT.indd 9NV-NVT-NYT.indd 9 2017/6/20 13:13:322017/6/20 13:13:32
P
M×P (N)(N)
(T) L (T)
d
EGC
A*
H
D
F
0-0.1B
*High grade: -0.2 Precision grade (UP): A-0.1 Ultra Precision grade (UP): A0 0
-0.10
One set consists of 4 rails, 2 R-retainers, and 8 end pieces.
1N≒0.102kgf
CN
CoN
2030204520602075209021052120213521502165218030503075310031253150317532003225408041204160420042404280
g3044587387101115130144158173102151200249297346395443269405536670801935
FN
F
M3
M4
M5
d
mm
G
mm
H
mm
T
mm
2.55
3.3
4.3
4.4
6
8
2
3.1
4.2
1.2
2
2
2,3203,1903,1904,0004,7605,4906,1906,8706,8707,5308,8006,1508,46010,60012,60014,50016,40018,20019,90012,10020,80024,80032,20035,80039,200
3,0504,5804,5806,1107,6309,16010,60012,20012,20013,70016,8008,06012,10016,10020,10024,20028,20032,20036,30015,70031,50039,30055,10063,00070,900
1,0101,5201,5202,0302,5403,0503,5604,0704,0704,5805,6002,6804,0305,3706,7208,0609,41010,70012,1005,25010,50013,10018,30021,00023,600
dynamic staticbasic load rating
size
allowable load
mass (one set)
10
SLIDE WAY
NV-NVT-NYT.indd 10NV-NVT-NYT.indd 10 2017/6/20 13:13:322017/6/20 13:13:32
NVTS 3 205
NVT TYPE-NVT1/NVT2/NVT3-
part number structure
12 18 25 32 40 45 50
17±0.1 30 11 10 M2 4 12.5 12 - 2.5 - M2 6
NVTS1025103510451055106510751085
25 35 45 55 65 75 85
-1×102×103×104×105×106×10
stroke
STmm
18304050607080901001101203045607590105130155
major dimensions
21±0.1
28±0.1
Amm
Bmm
Lmm
bmm
P1mm
S1 famm
Nmm
M×Pmm
h1mm
h2mm
t1mm
t2mm
S2 fbmm
-0.240-0.4
-0.2-0.4
60±0.1
14
18.5
15
25
M3
M4
6
8
17.5
27.5
16
40
-
-
3.4
5.5
-
-
M2
M3
6
6
NVT20352050206520802095211021252140215521702185
NVT30553080310531303155318032053230
NVTS20352050206520802095211021252140215521702185
NVTS30553080310531303155318032053230
35506580951101251401551701855580105130155180205230
-1×152×153×154×155×156×157×158×159×1510×15-1×252×253×254×255×256×257×25
NVT1025103510451055106510751085
part number
anti-corrosionstandard
table-top mounting hole dimensions
table-end mounting hole dimensions
The basic static load rating is the value at the center of the stroke.
example
specifi cationNVT : standardNVTS : anti-corrosion
table length
size
11
NV-NVT-NYT.indd 11NV-NVT-NYT.indd 11 2017/6/20 13:13:322017/6/20 13:13:32
P1 Dd
ht1
c1
c2
t2
Ab
h2 P2h1
L(N)M×PN
P
B
S1depth fa
S2fb
(f1) f2f4f6f7
f5f3
f1
depth
1025103510451055106510751085
87124160195231267303
39 55 71 87103119136
2.5×4.5×2.522 5.5 9 3.5
-------
---
-------
-------
-------
2222222
734 1,250 1,720 2,160 2,560 2,960 3,330
849 1,690 2,540 3,390 4,240 5,090 5,940
283 566 849 1,130 1,410 1,690 1,980
3.73 1.77 9.0914.124.933.147.8
3.18 4.2410.316.726.736.750.7
5.73 1.93 7.67 9.6115.317.223.0
18283848586878
MR MP
center of R-retainer
MY1N≒0.102kgf 1N・m≒0.102kgf・m
CNCoN
2035205020652080209521102125214021552170218530553080310531303155318032053230
g g
2002873774555506407308108909801,0706439601,2601,5801,8602,1602,4602,780
951401822252602953403704104504903034455907258601,0001,1401,310
FN
3.5×6.5×3.5
4.5×8×4.5
P2mm
d×D×hmm
30
40
c1mm
c2mm
f1mm
f2mm
f3mm
f4mm
f5mm
f6mm
f7mm
Tμm
Sμm
MPN・m
MYN・m
MRN・m
bed-surface mounting hole dimensions
accuracy※(deviation)
allowable static moment
6.5
9
10.9
15
5
10
---------------85110135160
---40557085100115130145------85110
-------------------
-------7085100115--------
----------85--------
2222233333322333333
4455566667755666777
1,3602,3303,1903,9904,7405,4606,1606,8308,1308,7509,3706,1508,44010,50014,40016,30018,10019,80021,500
1,5203,0504,5806,1107,6309,16010,60012,20015,20016,80018,3008,06012,10016,10024,20028,20032,20036,30040,300
5091,0101,5202,0302,5403,0503,5604,0705,0905,6006,1102,6804,0305,3708,0609,41010,70012,10013,400
10.1 18.9 36.9 53.2 80.3 104 130 171 235 275 317 20.8 125 188 300 508 630 763 906
8.8 18.7 35.7 53.8 79.9 106 135 176 244 289 338 37.2 119 186 319 505 635 779 936
13.7 18.6 32.4 37.3 51.1 56 60.9 74.7 88.4 93.3 98.3 27.3 140 167 195 308 335 362 390
2540557085100115130145160175356085110135160185210
28384858
4445555
dynamic staticbasic load rating allowable
loadNVT NVTS
mass
size
※For accuracy (T, S), refer to Figure 7 (page 2).
center of R-retainer
12
SLIDE WAY
NV-NVT-NYT.indd 12NV-NVT-NYT.indd 12 2017/6/20 13:13:322017/6/20 13:13:32
NVT 6 210
NVT TYPE-NVT4/NVT6/NVT9-
part number structure
45±0.1 100±0.1
60±0.1 145±0.1
stroke
STmm
35±0.1
Amm
Bmm
Lmm
bmm
P1mm
S1 famm
Nmm
M×Pmm
h1mm
h2mm
t1mm
t2mm
S2 fbmm
80±0.1
NVT408541254165420542454285
NVTS408541254165420542454285
NVT6110616062106260631063606410
NVT9210931094109510
-----------
50751051301551856095130165200235265130180220300
85125165205245285110160210260310360410210310410510
24
31
43
40 M5 10 42.5
50
85
M6
M8
12
16
55
105
-1×402×403×404×405×40-1×502×503×504×505×506×50-1×1002×1003×100
55 - 6.5 - M3 6
60
90
92
135
8
11
15
20
M4
M4
8
8
part number
anti-corrosionstandard
table-top mounting hole dimensions
table-end mounting hole dimensions
major dimensions
The basic static load rating is the value at the center of the stroke.
example
specifi cationNVT : standardNVTS : anti-corrosion
table length
size
13
NV-NVT-NYT.indd 13NV-NVT-NYT.indd 13 2017/6/20 13:13:322017/6/20 13:13:32
P1 Dd
ht1
c1
c2
t2
Ab
h2 P2h1
L(N)M×PN
P
B
S1fa
S2fb
(f1) f2f4f6f7
f5f3
f1depth
depth
1N≒0.102kgf 1N・m≒0.102kgf・m
CNCoN
408541254165420542454285
g g1,7102,5203,3204,1304,9305,730
7901,1601,5301,9002,2702,630
FN
P2mm
d×D×hmm
c1mm
c2mm
f1mm
f2mm
f3mm
f4mm
f5mm
f6mm
f7mm
Tμm
Sμm
MPN・m
MYN・m
MRN・m
12,10020,70024,70032,10039,00042,400
15,70031,50039,30055,10070,90078,700
5,25010,50013,10018,30023,60026,200
156 327 656 1,270 1,740 2,380
147 357 660 1,250 1,780 2,400
239 320 559 874 956 1,190
5.5×10×5.4
7×11.5×7
9×14×9
55
60
90
10.5 18 10
13
16
23
29
10
55
---105145185
------
------
------
------
233333
567777
6510514518522526590140190240290340390100200300400
--90140190240290----
-----140190----
-----------
-----------
-----------
-----------
33333443333
66777886677
61106160621062606310636064109210931094109510
3,3004,8506,3107,7909,26010,90012,46012,55018,00024,01030,100
29,60040,70060,60069,80078,80087,400104,00096,100143,000186,000206,000
37,50056,30093,900112,000131,000150,000187,000128,000213,000298,000341,000
12,50018,70031,30037,50043,80050,10062,60042,60071,10099,500113,000
1929371,9302,6604,4605,5707,4301,6206,50012,70018,700
3039271,9802,7704,4105,5807,6602,1106,58012,70018,600
2298811,3001,5302,3702,6002,8301,8104,8807,3209,760
MR MPMY
bed-surface mounting hole dimensions
accuracy※(deviation)
allowable static momentdynamic static
basic load rating allowable load
NVT NVTS
mass
size
※For accuracy (T, S), refer to Figure 7 (page 2).
center of R-retainercenter of R-retainer
14
SLIDE WAY
NV-NVT-NYT.indd 14NV-NVT-NYT.indd 14 2017/6/20 13:13:322017/6/20 13:13:32
NYT 2 065
NYT TYPE
NYT 12182532404550
25354555657585
1×181×281×201×302×201×302×30
1447.067.520±0.18±0.1 M2.6 3
3.5 3.512.512.512.522.512.5
NYTS
NYT 2035205020652080209521102125
NYT 3055308031053130315531803205
STmm
183040506070803045607590105130
B1
mm
A
mm
L
mm
M1×P2
mm
P1
mm
c
mm
B2
mm
b
mm
S1 f
mm
N1
mm
35506580951101255580105130155180205
1×281×431×301×452×301×452×451×401×651×501×752×501×752×75
22
30
6
8
12.4
16.7
11.5
15.5
30±0.1
40±0.1
12±0.1
16±0.1
M3
M4
5
7
3.53.517.517.517.532.517.57.57.527.527.527.552.527.5
NYTS 2035205020652080209521102125
NYTS 3055308031053130315531803205
1025103510451055106510751085
1025103510451055106510751085
part number
anti-corrosionstandard
stroke major dimensions table-top mounting hole dimensions
The basic static load rating is the value at the center of the stroke.
part number structure
example
specifi cationNYT : standardNYTS : anti-corrosion
table length
size
15
NV-NVT-NYT.indd 15NV-NVT-NYT.indd 15 2017/6/20 13:13:322017/6/20 13:13:32
S1
P1
B1
P2N1 M1×P2 (N1)
LAb
c
S2
B2
(N2) M2×P3 N2P3depth f
1025103510451055106510751085
M2.6
5 7.57.57.57.57.57.5
2×7.52×103×104×105×106×107×10
2222222
4455555
734 1,250 1,720 2,160 2,560 2,960 3,330
849 1,690 2,540 3,390 4,240 5,090 5,940
283 566 849 1,130 1,410 1,690 1,980
3.73 1.77 9.0914.124.933.147.8
3.18 4.2410.316.726.736.750.7
3.18 1.07 4.26 5.33 8.52 9.5912.7
25 35 45 55 65 76 86
1N≒0.102kgf 1N・m≒0.102kgf・m
CN
CoN
20352050206520802095211021253055308031053130315531803205
FN
S2 N2
mm
M2×P3
mm
M3
M4
7.510101010101010151515151515
1×202×153×154×155×156×157×151×352×253×254×255×256×257×25
Tμm
Sμm
MP
N・m
MY
N・m
MR
N・m
22222222233333
44555555555555
1,3602,3303,1903,9904,7405,4606,1606,1508,44010,50014,40016,30018,10019,800
1,5203,0504,5806,1107,6309,16010,6008,06012,10016,10024,20028,20032,20036,300
5091,0101,5202,0302,5403,0503,5602,6804,0305,3708,0609,41010,70012,100
10.1 18.9 36.9 53.2 80.3 104 130 23.6 125 188 302 508 630 763
8.8018.7
35.7 53.8 79.9 106 135 37.2 119 186 319 505 635 779
9.9313.4
23.4 26.9 36.9 40.4 44.0 17.0 87.2 104 121 191 208 225
g
84120157190225265305228345450570665780890
bed-surface mounting hole dimensions accuracy※(deviation) dynamic static
basic load rating allowable load
allowable static moment mass
size
※For accuracy (T, S), refer to Figure 7 (page 2).
MPMRMY
center of R-retainer
center of R-retainer
16
SLIDE WAY
NV-NVT-NYT.indd 16NV-NVT-NYT.indd 16 2017/6/20 13:13:322017/6/20 13:13:32
NYTS 3 D-125
NYT-D TYPE
NYT 1025-D1035-D1045-D1055-D1065-D1075-D1085-D
12 18 25 32 40 45 50
1×181×281×201×302×201×302×30
1447.067.520±0.18±0.1 M2.6 3
3.5 3.512.512.512.522.512.5
NYTS 1025-D1035-D1045-D1055-D1065-D1075-D1085-D
NYT 2035-D2050-D2065-D2080-D2095-D2110-D2125-D
NYT 3055-D3080-D3105-D3130-D3155-D3180-D3205-D
stroke
STmm
183040506070803045607590105130
major dimensionsB1
mm
A
mm
L
mm
M1×P2
mm
P1
mm
c
mm
B2
mm
b
mm
S1 f
mm
N1
mm
35506580951101255580105130155180205
1×281×431×301×452×301×452×451×401×651×501×752×501×752×75
22
30
6
8
12.4
16.7
11.5
15.5
30±0.1
40±0.1
12±0.1
16±0.1
M3
M4
5
7
3.53.517.517.517.532.517.57.57.527.527.527.552.527.5
NYTS 2035-D2050-D2065-D2080-D2095-D2110-D2125-D
NYTS 3055-D3080-D3105-D3130-D3155-D3180-D3205-D
25 35 45 55 65 75 85
part number
anti-corrosionstandard
table-top mounting hole dimensions
The basic static load rating is the value at the center of the stroke.
part number structure
example
specifi cationNYT : standardNYTS : anti-corrosion
table length
size
with counterbore
17
NV-NVT-NYT.indd 17NV-NVT-NYT.indd 17 2017/6/20 13:13:322017/6/20 13:13:32
S1
P1
B1
P2N1 M1×P2 (N1)
L
h
Ab
c
d D
B2
(f1) f2 f1f3depth f
1025103510451055106510751085
2.5×4.1×2.2
--2529313540
18 25 38 48 55 65 75
3.55 3.53.55 5 5
2222222
4455555
734 1,250 1,720 2,160 2,560 2,960 3,330
849 1,690 2,540 3,390 4,240 5,090 5,940
283 566 849 1,130 1,410 1,690 1,980
3.73 1.77 9.0914.124.933.147.8
3.18 4.2410.316.726.736.750.7
3.18 1.07 4.26 5.33 8.52 9.5912.7
25 35 45 55 65 76 86
1N≒0.102kgf 1N・m≒0.102kgf・m
CN
CoN
20352050206520802095211021253055308031053130315531803205
FN
d×D×h
mm
f3
mm
f2
mm
f1
mm
3.5×6×3.3
4.5×7.5×4.3
--3340455055-435565958590
253555708595110406890115140165190
57.55557.57.57.567.57.57.57.57.5
Tμm
Sμm
MP
N・m
MY
N・m
MR
N・m
22222222233333
44555555555555
1,3602,3303,1903,9904,7405,4606,1606,1508,44010,50014,40016,30018,10019,800
1,5203,0504,5806,1107,6309,16010,6008,06012,10016,10024,20028,20032,20036,300
5091,0101,5202,0302,5403,0503,5602,6804,0305,3708,0609,41010,70012,100
10.1 18.9 36.9 53.2 80.3 104 130 23.6 125 188 302 508 630 763
8.80 18.7 35.7 53.8 79.9 106 135 37.2 119 186 319 505 635 779
9.9313.4 23.4 26.9 36.9 40.4 44.0 17.0 87.2 104 121 191 208 225
g
84120157190225265305228345450570665780890
bed-surface mounting hole dimensions accuracy※(deviation) dynamic static
basic load rating allowable load
allowable static moment mass
size
※For accuracy (T, S), refer to Figure 7 (page 2).
MPMRMY
center of R-retainer
center of R-retainer
18
SLIDE WAY
NV-NVT-NYT.indd 18NV-NVT-NYT.indd 18 2017/6/20 13:13:322017/6/20 13:13:32
NIPPON BEARINGHead Offi ce2833 Chiya, Ojiya-city, Niigata-pref., 947-8503 JapanPhone: +81 (0)258-82-0011 FAX: +81 (0)258-81-1135Overseas direct call: +81 (0)258-82-5709http://www.nb-linear.co.jp/
NB CORPORATION OF AMERICA930 Muirfi eld Drive Hanover Park, IL 60133Phone: (630)295-8880 FAX: (630)295-8881TOLL FREE: (800)521-2045
Western Regional Offi ce46750 Lakeview Blvd. Fremont, CA 94538Phone: (510)490-1420 FAX: (510)490-1733TOLL FREE: (888)562-4175
Eastern Regional Offi ce500 N. Franklin Turnpike, Ramsey, NJ 07446Phone: (201)236-3886 FAX: (201)236-5112TOLL FREE: (800)981-8190
http://www.nbcorporation.com/[email protected]
NB EUROPE B.V.Boekweitstraat 21, 2153 GK Nieuw-Vennep, The NetherlandsPhone: +31 (0)252-463-200 FAX: +31 (0)252-643-209http://www.nbeurope.com/[email protected]
NB CHINA CO.,LTD.Room 108, Building 2, Randong Commercial Center No. 150,Lane 2161 Wanyuan Road, Minhang District, Shanghai 201103P.R. ChinaPhone: +86-21-5228-6811 FAX: +86-21-5228-6810http://www.nb-linear.co.jp/chinese/[email protected]
NIPPON BEARING MALAYSIA SDN. BHD.No. 27, Jalan PJS 11/14, Bandar Sunway, 46150 Petaling Jaya,Selangor Darul Ehsan, MalaysiaPhone: +60-3-5621-0716 FAX: +60-3-5621-0729 [email protected]
Reproduction Prohibited Specifi cations are subject to change without notice. No. 4600 First Edition: July 1. 2017
NV-NVT-NYT.indd 19NV-NVT-NYT.indd 19 2017/6/20 13:13:332017/6/20 13:13:33