Smart Can Data

8/13/2019 Smart Can Data

1/56

Ryder Towing Equipment LtdTF2302 SmartCAN Towing Module Fitting Guide

Quality Service InnovationAlvanley House, Alvanley Industrial Estate, Stockport Road East, Bredbury, Stockport, SK6 2DJ

Phone 0161 430 1120 (fax 0161 430 8140) www.rydertowing.co.uk

1

Introducing

SmartCAN

The Universal CANbus Towing Module

CONTENTS

SmartCAN Universal CANbus Towing Module ii (2)

Introduction to the module iii -iv(3-4)

Fitting procedure v (5)

Generic guide to all vehicles covered vi-ix (6-9)

Index to vehicle-specific sheets x-xi (10-11)

Vehicle-specific sheets New section after xi Pages 1-46


2/56




2

SmartCAN Universal CANbusTowing Module

Interfaces directly to CAN - Identifies the vehicle it is fitted in

Enables activation of cars towing related functions

**Has builtin caravan auxiliary function.

Interfaces directly to CAN

The TF2302 towing module connects directly to the vehicles CANbus network. All the signal data to the towing

module comes from a direct connection to the vehicles CAN HI, CAN LO wires.

Identifies the vehicle in which it is fitted: dedicates itself

As soon as the module is connected and powered up, it analyses the data the car is sending, recognises the vehicle it

is in, dedicates itself to that vehicle and applies the correct codes.

Enables activation of cars towing related functions

When the vehicle requires data from the towing module to activate towingrelated functions, the smart module

sends it.

**Caravan auxiliary function.

The SmartCAN module has a CANactivated 12S function to control caravan auxiliary circuits. Two switched 12S

outputs on the module are activated when the CAN detects that the engine is running.

The diagram below shows the module and the short loom.

Clig gauche/LH flasherMasse/ChassisAnalogue brake input (green/white)C2 (pink)CAN LO (blue/black)CAN HI (yellow/red)Clig droit/RH flasherVeilleuse droite/RH tailStops outputVeilleuse gauche/LH tailRecul/reverse (yellow/white)Antibrouillard/fog

Ryd er TF2302

Smar tCAN

Towing mo dule

1.2.3.4.5.6.7.8.9.10 .11.12 .

1 12N + 12v Input2 12S + 12v Input3 12S + 12v Input4 12S switched output5 12S switched output

12 11 10 9 8 7

6 5 4 3 2 1 21 3 4 5

Pin designations

+12V

CAN HICAN LO

C2

Hardbrakesignal

12 Sswitchedoutputs

12Nandreverseoutputs

13-pinor12Sand12 Nsockets

To car To trailer


3/56




3

Introduction to the module12-pin connector: pin designations are shown in the diagram on the previous page.

The short loom that mates with this socket carries the following circuits:

CAN HI and CAN LO: From Pins 5 and 6, a blue/black. wire and a red/yellow wire.

The blue/black wire is CAN HI and the red/yellow wire is CAN LO. Each has a butt connector

attached.

You need grey two-core data cable* to connect to CAN in the vehicle.

(*This cable is available in 50M coils from Ryder Towing. If you have bought the SmartCAN module as part of a complete kit,

the kit should contain a 5.5 metre coil of data cable.)

C2: Pink

This wire is a negative switch for an external C2 trailer flasher warning lamp or buzzer. There is no

buzzer on board the module. Connect one end of the buzzer/lamp to live and the other to this wire.

Hard (analogue) brake input* Green/white single unterminated wire.

Some cars do not have brake lights on the CAN so a hard brake connection is required. Also, it is

common for a belt and braces approach to be used, with the hard brake connection made even

if there is a brake function on the cars CANbus system. The brake signal has to be picked up from a

feed that supplies a single function bulb. not from a modulated feed that operates both the brake

light and sidelight (otherwise the trailer brakes will come on with the sidelights).

Earth: White single unterminated wire:

This is the earth for the module only. Earth to the chassis

6 outputs to the trailer socket.

Yellow, blue, green, brown, red, black and yellow/white. Fit a prewired trailer socket (7-pin or 13-pin) in the normal way, thread the cable into the car and connect the socket wires to the

corresponding colours on the short loom. Connect the trailer reverse light wire to yellow/white on

the short loom.

5-way screw terminal block

This block carries 12N and 12S power inputs and two switched caravan auxiliary outputs:

Pin 1: 12V input for trailer light outputs. Protect with a 15 amp fuse, close to power source.

Pin 2: 12V input for caravan auxiliary outputs. Protect with a 15 amp fuse close to the power source.

Pin 3: 12V input for caravan auxiliary outputs. Protect with a 15 amp fuse close to the power source.

Pin 4: Switched 12V output CAN controlled

Pin 5: Switched 12V output CAN controlled

Clig gauche/LH flasherMasse/ChassisAnalogue brake input (green/white)C2 (pink)CAN LO (blue/black)CAN HI (yellow/red)Clig droit/RH flasherVeilleuse droite/RH tailStops outputVeilleuse gauche/LH tailRecul/reverse (yellow/white)Antibrouillard/fog

Ryder TF2302

Smar tCAN

Towing module

1.2.3.4.5.6.7.8.9.10.11.12.

1 12N + 12v Input2 12S + 12v Input3 12S + 12v Input4 12S switched output5 12S switched output

12 11 1 0 9 8 7

6 5 4 3 2 1 21 3 4 5

Pin designations

+12V

CAN HICAN LO

C2

Hardbrakesignal

12Sswitchedoutputs

12Nandreverseoutputs

13-pinor12Sand12Nsockets

To car To trailer


4/56




4

The 12N wires from the trailer

socket (7 or 13-pin) connect to

these butt terminals

Hard brake

connection

White to chassis earth

The C2 warning connects

to the pink wire

To trailer reverse

Screw terminals

1. +12V 12N in

2. +12V 12S in

3. +12V 12S in

4. Switched 12S out

5. Switched 12S out

The data cable

(twisted pair) from

CAN HI & CAN LO

connects here

Coil of data cable:Different

lengths (from less than 1m to

5.5m) are required in

different cars. We

recommend buying in 50m

coils and cutting to required

lengths from job to job.

SmartCAN module with

short loom

The picture on the left showshow the short loom makes all

the wiring connections

simple.

Self-crimp option.

Connecting wires are brought directly to the plug. Using the

crimp tool* (TT7702) the crimp terminals are attached to

the wires and pushed into the correct cells in the housing.

The map of cell allocations is printed on the top of the

module. (*To ensure good, gas-tight connections, use of the

correct crimp tool is essential.)

Simple and cost-effective

This is the simplest and most cost-effective option, with the

fewest connections within the system. The housing and

crimps (WT2121HC) cost well under a pound.

Easy

The special crimp tool is easy to use and used with care,

virtually guarantees high-quality connections.

Long loom option

WT2121 Full 7-core loom, 2 metres: 12-way plug with 2 metres of 7-core cable, 5.5 metres of twisted data cable

plus earth, hard brake and C2 cables. Trailer socket not connected.


5/56




5

FITTING PROCEDUREDisconnecting the battery: If you do disconnect the battery, make sure the ignition is switched off before you

disconnect. Only disconnect for the shortest possible time.

Refer to Practical Guide atwww.rydertowing.co.ukfor general fitting information.

Details for all cars of where to connect and details of the CAN interface are given on the master sheet in later pages, and on the

car- specific sheets (SmartCAN Data) available in CarData at www.rydertowing.co.uk.

Install all components, including connecting the module to the trailer cable(s). If you decide to

disconnect the battery, do so now.

Make your connections to Can HI and CAN LO. The HI and LO wires are always a twisted pair. If the

instruction refers you to a connector or OBD2, connect to the wires leading to the specified pins.

Cut a suitable length of the grey two-core data cable and connect one end to the red/yellow and

blue/black CAN wires in the short loom, red to red/yellow and black to blue/black.

Connect the other end to the vehicle CAN wires: red to CAN HI, black to CAN LO.

NOTE: The connections to CAN HI and CAN LO have to be excellent, and soldering is not

recommended because of potential heat transfer to sensitive circuits in the car, so each

kit includes a SuperSplice connector. We strongly recommend its use for this interface.

Connect both power inputs to the power source but do not fit the fuses. If you have

disconnected the battery, reconnect it now.

Switch on the ignition.

Insert the fuses that protect the module and test the installation.

If you have connected the wrong way round to CAN HI / CAN LO, you will not damage the vehicle or the unit, but the

module will not work. The LED in the module will flash in the sequence: 3 rapid - pause/3 rapid - pause, etc. In this

case, simply reverse your connections to HI and LO.

The correct flash sequence is:

o REGULAR 1 SECONDlocked on and working

Error sequences are:

o NONENo CAN detected or asleep

o STEADYIncompatible with vehicle

o 3 RAPID - PAUSE/3 RAPID - PAUSE, etcCAN wires reversed.

Overload protection: As well as the fuse protection you put on the input cables, the module has on board protection against

overloadsit will shut down any lighting circuit that shorts, etc. In service, making this a very durable unit.

The SmartCAN module recognises the host vehicle: Data from all the vehicles on the application list is programmed into the

Smart module. Once fitted, the module recognises its host and becomes specific to that vehicle.

If the module sends trailer data back to the vehicle: Some vehicles automatically accept data back from the unit and alter some

functions when a trailer is connected. Some require a recode before they do this and others react partially without a recode,

adding new functions when they have been recoded. Recode information is given on the car-specific sheets.

Generic instruction sheets and Car-specific pages: The following pages list all vehicles currently covered and give concise fitting

instructions for each. Car-specific pages can be downloaded as a PDF file fromwww.rydertowing.co.uk.

OBD II: In some cases, the CAN connection is found on the cars diagnostic socket (OBDII)

OBD II(On-board diagnostic) data link connectors (DLC) are the international standard for the diagnostic interface. They have to

be within easy reach of the drivers seat, sometimes in the centre console, sometimes under the dash. Two of the pins are CAN

HI, CAN LO and these are listed in the data chart in these

instructions.

The images on the right show what an OBD II connector looks like.
http://www.rydertowing.co.uk/http://www.rydertowing.co.uk/http://www.rydertowing.co.uk/http://www.rydertowing.co.uk/http://www.rydertowing.co.uk/http://www.rydertowing.co.uk/http://www.rydertowing.co.uk/http://www.rydertowing.co.uk/http://www.rydertowing.co.uk/http://www.rydertowing.co.uk/http://www.rydertowing.co.uk/http://www.rydertowing.co.uk/


6/56

Ryder Towing SmartCAN Module TF2302Fitting Guide

Vehicle Make Model YearsModule

type

CAN

high/low

location

High/low

colours/

from pins

Power

source

Fusebox

(/117)

location

Socket

cable entry

Hard brake

connection

2-way

dataAuto add

Recode adds:

TSP if available

plus

CommentNote: Please let us know if you see

any errors in our data or if you can

add information

Audi A3 2009> Stan. JR45-113 301/302 117 JR45 M60 /119 JR45/113 Y FCO C2/PDC/Brake Possible dealer code issues

Audi A4 2008 > Stan. JR45-113 301/302 117 JR45 M60 /119 JR45/113 Y FCO C2/PDC/Brake Possible dealer code issues

Audi A5 2008 > Stan. JR45-113 301/302 117 JR45 M60 /119 JR45/113 Y FCO C2/PDC/Brake Possible dealer code issues

BMW 1 Series 2004 > Stan. B9/111 301/310 117 JL42-43 M60 Y C2, PDC/FCO




BMW X5 2007 > Stan. JR45 301/310 117 JR45 I40/119 JR45/324 Y C2, PDC/FCO CAN also at B9

Chevrolet Captiva 2007 > Stan. OBDII Pins 1/4 137 A4 NCitroen Berlingo 2008 > Stan. C10/125 319/308 117 B7/118 I38/119 JL42/325 Y C2/PDC/FCO

Citroen C4 2005 > Stan. M59 332/333 117 B7/118 I38/119 JL42/325 Y C2, PDC/FCO

Citroen C4 Picasso 2008 > Stan. JL42 331/311 117 A4 I38/119 JL42/330 Y C2, PDC/FCO

Citroen C5 2008 > Stan. JL42/125 318/319 117 B7/118 I38/119 JL42/125/321 Y C2, PDC/FCO

Citroen Dispatch 2007 > Stan. JL42/125 JL43/125 C11 N61 JL42/310 Y C2, PDC/FCO Add fuse position H

Fiat Scudo 2007 > Stan. JL42/125 JL43/125 C11 N61 JL42/310 Y C2, PDC/FCO Add fuse position H

Ford Mondeo 2007 > Stan. JR45 303/304 117 JL42 140/141 JL42/322 Y C2, PDC/FCO

Ford S-Max 2008 > Stan. JR45 303/304 117 JL42 140/141 JL42/322 Y C2, PDC/FCO

Land Rover Freelander 2 2007 > Stan. JL42-125 139 JL42/125 JL42 I38/119 JL42/322 Y C2?, PDC/FCO

Mercedes C Class (203) 2001 > Stan. JL42/127 317/311 117 JL42 M58/119 Y PDC/FCO C2

Mercedes CLK (209) 2002 > Stan. JL42/127 317/311 117 JL42 M58/119 Y PDC/FCO C2

Mercedes E Class (211) 2002 > Stan. JL42/127 317/311 117 JL42 M58/119 Y PDC/FCO C2

Mercedes M Class (W164) 2005> Stan. JR45/125 317/311 117 JR45 JR45/119 JR46 /320 Y PDC/FCO C2

Nissan Cube 2001 > Stan. OBDII Pins 6/14 117 N

Nissan Micra (K12) 2003 > Stan. OBDII Pins 6/14 117 I39 N

Nissan Note 2006 > Stan. OBDII Pins 6/14 117 I39 N

Nissan Navara 2005 > Stan. OBDII Pins 6/14 117 N

Nissan Pathfinder 2005 > Stan. OBDII Pins 6/14 /117 I40/119 N

Peugeot 307 2005 > Stan. JL42 319/308 117 B7 /118 I38/119 JL42/318 NPeugeot 308 2008 > Stan. JL42 319/308 JL42 beige B7 /118 I38/119 JL42/327 Y

Peugeot Partner 2008 > Stan. C10/125 319/308 117 B7/118 I38/119 JL42/325 Y C2/PDC/FCO

Peugeot Expert 2007 > Stan. JL42/125 JL43/125 C11 N61 JL42/310 Y C2, PDC/FCO Add fuse position H

Renault Laguna 3 2008 > Stan. OBDII Pins 6/14 JR48 JL42/310 N

Renault Megane 3 2009 > Stan. OBDII Pins 6/14 117 I39 JR46/328 N

Seat Altea 2008 > Stan. B9-113 301/302 B9/125 B9 M60 /119 Y FCO C2/PDC/Brake Late models may be coded

Seat Exeo 2009 > Stan. B9-113 301/302 B9/125 B9 M60 /119 Y FCO C2/PDC/Brake Late models may be coded

Seat Leon 2005 > Stan. B9-113 301/302 B9/125 B9 M60 /119 Y FCO C2/PDC/Brake Late models may be coded

Skoda Octavia 2005 > Stan. B9-113 301/302 B9/125 B9 M58-9/119 JL42-43/329 Y FCO C2/PDC/Brake Late models may be coded

Skoda Octavia II 2009 > Stan. B9-113 301/302 B9/125 B9 M58-9/119 Y FCO C2/PDC/Brake Late models may be coded

Numbers below with a letter in front refer to the diagram. Numbers only refer to "Further Details"

Ryder Towing Equipm ent Ltd - Quality, Service, Innovation - www.rydertowing.co.uk


7/56


Vehicle Make Model YearsModule

type

CAN

high/low

location

High/low

colours/

from pins

Power

source

Fusebox

(/117)

location

Socket

cable entry

Hard brake

connection

2-way

dataAuto add

Recode adds:

TSP if available

plus

CommentNote: Please let us know if you see

any errors in our data or if you can

add information

Numbers below with a letter in front refer to the diagram. Numbers only refer to "Further Details"

Skoda Superb II 2009 > Stan. B9-113 301/302 B9/125 B9 M58-9/119 Y FCO C2/PDC/Brake Late models may be coded

Skoda Yeti 2009 > Stan. B9-113 301/302 B9/125 B9 M58-9/119 Y FCO C2/PDC/Brake Late models may be coded

Vauxhall Astra 2005 > GM OBDII Pins 1/4 117 JL42 /43 M58 /119 N FCO

Vauxhall Astra Sedan 2010 > GM OBDII Pins 1/4 117 B7/118 I38 /119 Y C2?, PDC/FCO

Vauxhall Astra SW 2010 > GM ...........See note.................... I38 /119 Y C2?, PDC/FCO Use plug-in kit TF120VX

Vauxhall Corsa 2005 > GM OBDII Pins 1/4 117 JL43 M60 N FCO

Vauxhall Ins ignia Sedan 2009 > GM OBDII Pins 1/4 117 B7/118 I38 Y C2?, PDC/FCOVauxhall Insignia SW 2009 > GM ...........See note.................... I38 /119 Y C2?, PDC/FCO Use plug-in kit TF120VX

Vauxhall Meriva 2010 GM OBDII Pins 1/4 117 JL43 I38 /119 Y C2?, PDC/FCO

Vauxhall Signum 2005 > GM OBDII Pins 1/4 117 JL43 I38 N FCO

Vauxhall Vectra 2005 > GM OBDII Pins 1/4 117 JL43 I38 N FCO

Vauxhall Zafira 2005 > GM OBDII Pins 1/4 117 JL43 M58 /119 N FCO

Volvo S80 2006> Stan. OBDII Pins 3/11 JL43/125 JL43 I38 Y C2?, PDC/FCO

Volvo V70 2007 > Stan. OBDII Pins 3/11 117 JL43 I38 Y C2?, PDC/FCO

Volvo XC60 2007> Stan. OBDII Pins 3/11 117 JL43 I38 Y C2?, PDC/FCO

Volvo XC70 2007> Stan. OBDII Pins 3/11 117 JL43 I38 Y C2?, PDC/FCO

Volkswagen Golf 2005 > Stan. B9-113 301/302 B9-110/204 B9 M60 /119 Y FCO C2/PDC/Brake Late models may be coded

Volkswagen Golf VI 2008 > Stan. B9-113 301/302 B9-110/204 B9 M60 /119 Y FCO C2/PDC/Brake Late models may be coded

Volkswagen Jetta 2005 > Stan. B9-113 301/302 B9-110/204 B9 M60 /119 Y FCO C2/PDC/Brake Late models may be coded

Volkswagen Passat 2005 > Stan. B9-113 301/302 B9-110/204 B9 M60 /119 Y FCO C2/PDC/Brake Late models may be coded

Volkswagen Tauran 2008 > Stan. B9-113 301/302 B9-110/204 B9 M60 /119 Y FCO C2/PDC/Brake Late models may be coded

Volkswagen Tiguan 2008 > Stan. B9-113 301/302 B9-110/204 B9 M60 /119 Y FCO C2/PDC/Brake Late models may be coded



8/56


Ref Comment Ref Comment Ref Comment

109 Bumper 204 Fuse terminal (Power Tap) 301 Orange/green

110 Bus bar 207 PDC cut off 302 Orange/brown

111 Rear of instruments 208 Fog cut off 303 Grey/orange

112 Chassis 209 C2 display on dash 304 Violet/orange

113 Control centre 210 Radio: ISO plug /quadlock 305 Yellow/red

114 Cover 211 306 Yellow/brown

115 Cross member 212 307 Pink

116 Behind cushions 213 308 White

117 Fusebox 214 309 Yellow/black118 Behind/below glove box 215 310 Green

119 Grommet 216 311 Brown

120 Interior lamp 217 312 Blue/red

121 By jack 218 313 Grey/red

124 Light access cover 219 314 Green/red

125 Connector block 220 315 Green/black

126 Lighter socket 221 316 Yellow

127 Loom 222 317 Brown/red

128 Number plate light 223 318 Purple

129 Panel/Trim 224 319 Red

130 Pedals 225 320 Blue/black

131 Roof lining 226 321 Violet

132 Spare wheel pan 227 322 Purple/brown

133 Radio 228 323 Black/red

134 Throttle pedal 229 324 Black/yellow

135 Towing plug 230 325 Blue

136 Vent 231 326 Grey

137 Battery 232 327 Blue

138 Lamp/cluster 233 328 Black139 Twisted pair on plug 234 329 White/yellow

140 Depends on model. 235 330 Light brown

141 Possibly drill 236 331 Red/black

142 237 332 Red/blue

143 238 333 Brown/yellow

144 239 334

145 240 335

What the numbers mean

A Engine compartmentB DashC Footwell & front bulkheadD Centre consoleE Door kick platesF Centre pillarsG Roof liningH Parcel shelf seat backsI Boot floorJL Boot side LeftJR Boot side RightK Boot lidL Hinge gaiters

M Rear panel of bootN Rear pillars (Vans, Estates)O Main cabin area

11

G29 G30 G31

H32 H33 H34

48 45

46

47

C

E

13

JR

F

20

B7 B8 B9

10 14 D

1516

17 18 F

19

2324

25

26 27 28

4441

42

43

I35 I36 I37I38 I39 I40

L50 L51

55 56 57

52 53 54

58 59 60

JL

K

C

E

12

M

1

4

2

5

3

6

A

N

61

N

62

E

21E

22

O



9/56

Ryder Towing Equipment Ltd

SmartCAN Fitting Guides ContentsUse Thumbnails, Page number or Search to select the page you need

Audi Year Page

Audi A4 and A5 All 2008 - 1

BMW Year Page

BMW 1, 3, 5, & 7 Series All 2005 - 2

BMW X5 4WD Apr 2007 - 3

Citroen Year Page

Citroen C4 Picasso MPV 2004 - 5

Citroen C4 Saloon etc Nov 2004 - 6

Citroen C5 Saloon etc Oct 2008 - 7

Citroen Despatch Van 2008 - 8

Fiat Year Page

Fiat Scudo Van 2007 - 9

Ford Year Page

Ford Mondeo Mk 4 All 2007 - 11

Ford S-Max MPV 2006 - 12

Landrover Year Page

Landrover Freelander II 4WD 2007 - 13

Mercedes Year Page

Mercedes C Class (203) Saloon 2005 - 14

Mercedes CLK (209) Saloon etc 2005 - 15

Mercedes E Class (211) Saloon 2002 - 16

Mercedes ML (W169) 4WD 2005 - 17

Nissan Year Page

Nissan Cube All 2001 - 18

Nissan Micra All 2002 - 19

Nissan Navara Pickup Aug 2005 - 20Nissan Note All 2007 - 21

Nissan Pathfinder All 2005 - 22

Peugeot Year Page

Peugeot 307 All Oct 2005 - 23

Peugeot 308 Hatchback July 2007 - Oct 2008 24

Peugeot Expert Van 2007 - 25

Peugeot Partner Van 2008 - 26

27 September 2010


10/56

Ryder Towing Equipment Ltd

SmartCAN Fitting Guides ContentsUse Thumbnails, Page number or Search to select the page you need

Renault Year Page

Renault Laguna Hatchback 2008 - 27Renault Megane All 2010 - 28

Seat Year Page

Seat Altea All 2004 - 29

Seat Exeo All 2009 - 30

Seat Leon All 2006 - 31

Skoda Year Page

Skoda Octavia Estate 2005 - 32

Skoda Octavia Hatchback July 2004 - 33

Skoda Superb Saloon 2009 - 34

Vauxhall Year Page

Vauxhall Astra All 2010 - 36

Vauxhall Corsa All 2007 - 37

Vauxhall Insignia Sedan/Hatchback 2009 - 38

Vauxhall Insignia SW and Astra SW 2009 - 39

Vauxhall Vectra/Signum All 2005 - 40

Vauxhall Zafira MPV 2005 - 41

Volkswagen Year PageVolkswagen Golf V All May 2004 - 42

Volkswagen Golf VI All 2008 - 43

Volkswagen Passat Saloon etc Late 2005 - 44

Volkswagen Tiguan AWD 2008 - 45

Volvo Year Page

Volvo S80 (06-) V70/XC60/XC70 (07-) All 2007 - 46

27 September 2010


11/56

SmartCAN fitting guide Audi A4 and A5 All 2008 -

Socket cable entry point M60 Grommet

CAN HI/LO location JR45 Control centre

HI/LO pins/colours HI Orange/green, LO Orange/brown

Is data two way? Yes

Recode data below: recode adds: C2 on dash; PDC; TSP; Auto hold brake adjustment

Hard brake connection JR45 Control panel

Power source Fusebox

Fusebox Location JR45

Audi:

Vehicle self-diagnosis:Gateway assembly list: 19-diagnosis interface for data bus Coding (Service 1A) Switch to coded!

K E Y T O Z O N E S O N T H E P L A NA E n g i n e c o m p a r t m e n tB D a s hC F o o t w e l l / a re a b e l o w d a s hD C e n t r e c o n s o l eE D o o r k i c k p l a t e sF Centre pi l larsG R o o f l i n in gH P a r c e l s h e l f s e a t b a c k s

4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2

I B o o t f l o o rJ L B o o t s i d e L e f tJ R B o o t s i d e R i g h tK B o o t l i dL H inge ga itersM R e a r p a n e l o f b o o tN Rear pi l lars (Vans, etc.)O M a i n c a b in a r e a

The boxes below show key fittting details - Cable entry point, CAN connection details, etc. Alpha-

numeric references (e.g. A4) refer to the car map at to foot of the page .

VAG: Park assist:Gateway assembly list:76-park assist system:07-code control unit Add 10000 to current coding; Re-

program (Vehicles 2008+usually pre-coded for towing module)

You may have to switch ignition on/off, click

key fob, etc. to activate CAN on the vehicle.

If you connect CAN HI CAN LO the wrong wayround, you will not do any damage to the

vehicle or the module. The LED in the modulewill flash rapidly three times, pause, flash

again, etc.Just reverse the CAN connecions you have

made. When the module recognises thevehicle and starts working, the LED will flashonce every second. If the module does not

recognise the vehicle, either the LED will lightconstantly or nothing will happen.

Trailer Stability ProgramIf TSP is available, the module will enable it to

be activated, either automatically or byrecoding, according to the vehicle.

Possibly affects cooling system control.

Consult dealer.See Audi Service Net

Also possible coding issues with dealer.

Ryder Towing Equipm ent Ltd


12/56

SmartCAN fitting guide BMW 1, 3, 5, & 7 Series All 2005 -

Socket cable entry point M60

CAN HI/LO location B9, behind instrument cluster

HI/LO pins/colours HI Orange/green, LO Green


Recode data below: recode adds: Optional

Hard brake connection N/A

Power source Fusebox.

Fusebox Location JL42 /43

Functions added automatically: C2 on dash; PDC; FCO


4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2




You may have to switch ignition on/off, clickkey fob, etc. to activate CAN on the vehicle.










13/56

SmartCAN fitting guide BMW X5 4WD Apr 2007 -


CAN HI/LO location JR45 twisted pair

HI/LO pins/colours HI Orange/green, LO Green


Recode data below: recode adds: N/A

Hard brake connection JR45 Black/yellow



Functions added automatically: C2 on dash; PDC; FCO


4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2




CAN also at B9


If you connect CAN HI CAN LO the wrong wayround, you will not do any damage to thevehicle or the module. The LED in the module

will flash rapidly three times, pause, flashagain, etc.

Just reverse the CAN connecions you havemade. When the module recognises the

vehicle and starts working, the LED will flashonce every second. If the module does not






14/56

BLANK


15/56

SmartCAN fitting guide Citroen C4 Picasso MPV 2004 -

Socket cable entry point I38 Grommet

CAN HI/LO location JL42 Twisted pair on connector

HI/LO pins/colours HI Red, LO Brown


Recode data below: recode adds: C2 display, park assist cut off

Hard brake connection JL42 yellow wire on connector block


Fusebox Location B7, behind or below glovebox

Remote loading / remote coding >Installation / de-installation>selection vehicle type> > trailer control unit (BSR)>

Installation of equipment


4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2





If you connect CAN HI CAN LO the wrong way

round, you will not do any damage to thevehicle or the module. The LED in the module









16/56

SmartCAN fitting guide Citroen C4 Saloon etc Nov 2004 -

Socket cable entry point

CAN HI/LO location M59 in loom (1 of 2 twisted pairs)

HI/LO pins/colours HI Red/blue, LO Brown/yellow



Hard brake connection N61 White wire (1 of 5)



Remote loading / remote coding >Installation / de-installation>selection vehicle type> > trailer control unit (BSR)>

Installation of equipment


4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2















17/56

SmartCAN fitting guide Citroen C5 Saloon etc Oct 2008 -


CAN HI/LO location JL42 Twisted pair

HI/LO pins/colours HI purple, LO red


Recode data below: recode adds: C2 display; Fog & Park Assist cut off

Hard brake connection JL42 thick purple with twisted pair



Autologic, etc.

Start diagnostics/Press Towbar/Select Citroen or Peugeot or Fiat/Press Trailer Module/Press Edit by Trailer

Module Status/Press Fitted


4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2














18/56

SmartCAN fitting guide Citroen Despatch Van 2008 -

Socket cable entry point N61 grommet

CAN HI/LO location JL42 Connector block




Hard brake connection JR46 Green wire


Fusebox Location C11 Add fuse, position H

Autologic, etc.




4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2














19/56

SmartCAN fitting guide Fiat Scudo Van 2007 -









Autologic, etc.




4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2














20/56

BLANK


21/56

SmartCAN fitting guide Ford Mondeo Mk 4 All 2007 -

Socket cable entry point Saloon I39, Estate I40 possibly drill

CAN HI/LO location OBDII or connector at JR45

HI/LO pins/colours Pins 3/11 or Grey/orange, Violet/orange



Hard brake connection JL42 Purple/brown wire


Fusebox Location JL42

Ford Recode information:

>Programmable parameter >Vehicle configuration parameter >Vehicle configuration

>Upload Veh Config file> Modify Veh Config file >Trailer module(Select "Trailer module 7(or 13)-position socket.


4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2

I B o o t f l o o rJ L B o o t s i d e L e f tJ R B o o t s i d e R i g h tK B o o t l idL H i n g e g a i te r sM R e a r p a n e l o f b o o tN Rear pi l lars (Vans, etc.)O M a i n c a b in a r e a














22/56

SmartCAN fitting guide Ford S-Max MPV 2006 -

Socket cable entry point JR46 Grommet

CAN HI/LO location OBDII or connector at JR45

HI/LO pins/colours Pins 3/11 or Grey/orange, Violet/orange






Ford Recode information:

>Programmable parameter >Vehicle configuration parameter >Vehicle configuration

>Upload Veh Config file> Modify Veh Config file >Trailer module(Select "Trailer module 7(or 13)-position socket.


4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2

I B o o t f l o o rJ L B o o t s i d e L e f tJ R B o o t s i d e R i g h tK B o o t l idL H i n g e g a i te r sM R e a r p a n e l o f b o o tN Rear pi l lars (Vans, etc.)O M a i n c a b in a r e a














23/56

SmartCAN fitting guide Landrover Freelander II 4WD 2007 -

Socket cable entry point I38 Grommet

CAN HI/LO location OBDII or twisted pair at JL42

HI/LO pins/colours On OBDII, Pins 3/11






Freelander recode info:

>Add/Remove Acessories

>Trailer module>A-1dd Accessories

>JI_TRAIL_MOD_13P_12N_12S


4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2














24/56

SmartCAN fitting guide Mercedes C Class (203) Saloon 2005 -

Socket cable entry point M59/60 Grommet

CAN HI/LO location JR45 twisted pair

HI/LO pins/colours HI Brown/red, LO Brown


Recode data below: recode adds: C2 display

Hard brake connection JR45

Power source Battery


Connect>Start>Special functions>Input for retrofits or conversions>user name and password>"550" in upper +

field>Accept & close>>Start again>Controllers View>"CGW">"Adjust">LHS "Configurations SCN encoding">online

wait>entry 550+ shows>Accept.


4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2




Functions added automatically: PDC; FCO












25/56

SmartCAN fitting guide Mercedes CLK (209) Saloon etc 2005 -






Hard brake connection N/A


Fusebox Location JL42 /43

> Control devices > Construction > ZGW - central gateway

> Read and change if necessary > Trailer recognition (switch to present)> Execute coding (F5).


4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2















26/56

SmartCAN fitting guide Mercedes E Class (211) Saloon 2002 -






Hard brake connection JL42






4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2















27/56

SmartCAN fitting guide Mercedes ML (W169) 4WD 2005 -





Recode data below: recode adds: ?

Hard brake connection JR46 Black/red






4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2















28/56

SmartCAN fitting guide Nissan Cube All 2001 -


CAN HI/LO location OBDII

HI/LO pins/colours Pins 6/14

Is data two way? No


Hard brake connection


Fusebox Location

K E Y T O Z O N E S O N T H E P L A N

A E n g i n e c o m p a r t m e n tB D a s hC F o o t w e l l / a re a b e l o w d a s hD C e n t r e c o n s o l eE D o o r k i c k p l a t e sF Centre pi l larsG R o o f l i n in gH P a r c e l s h e l f s e a t b a c k s

4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 6

4 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2














29/56

SmartCAN fitting guide Nissan Micra All 2002 -




Is data two way? No




Fusebox Location



4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 6

4 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2














30/56

SmartCAN fitting guide Nissan Navara Pickup Aug 2005 -




Is data two way? No




Fusebox Location



4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 6

4 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2














31/56

SmartCAN fitting guide Nissan Note All 2007 -




Is data two way? No




Fusebox Location



4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 6

4 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2














32/56

SmartCAN fitting guide Nissan Pathfinder All 2005 -




Is data two way? No

Recode data below: recode adds:



Fusebox Location



4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 6

4 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2














33/56

SmartCAN fitting guide Peugeot 307 All Oct 2005 -



HI/LO pins/colours HI Purple, LO White



Hard brake connection JL42 Purple wire



Peugeot PPS tester - Select vehicle

Select Peugeot Planet 2000

Optional extrasTow hook: Set trailer hook to present

Remote coding with F1


4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2














34/56

SmartCAN fitting guide Peugeot 308 Hatchback July 2007 - Oct 2008



HI/LO pins/colours HI Purple, LO White



Hard brake connection JL42, Blue wire



Peugeot PPS tester

Select vehicle> select application -Peugeot Planet 2000> Optional extras> Towing hook > install tow bar

K E Y T O Z O N E S O N T H E P L A NA E n g i n e c o m p a r t m e n tB D a s hC F o o t w e l l / a re a b e l o w d a s hD C e n t r e c o n s o l eE D o o r k i c k p l a t e sF Centre pi l larsG R o o f l i n in g

H P a r c e l s h e l f s e a t b a c k s

4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2




Autologic, etc.













35/56

SmartCAN fitting guide Peugeot Expert Van 2007 -









Autologic, etc.




4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2














36/56

SmartCAN fitting guide Peugeot Partner Van 2008 -

Socket cable entry point JL42 Grommet

CAN HI/LO location C10 Connector block

HI/LO pins/colours 10-pin connector, cells 3 HI and 5 LO



Hard brake connection N61 White wire


Fusebox Location A4 or A6

Peugeot PPS tester

Select vehicle> select application -Peugeot Planet 2000> Optional extras> Towing hook > install tow bar


4 34 1

4 2

1 1

G 2 9 G 3 0 G 3 1

H 3 2 H 3 3 H 3 4

4 8 4 5

4 64 7

C

E

1 3

J R

F

2 0

B 7 B 8 B 9

1 0 O 1 4 D

1 5O 1 6

O 1 7 O 1 8 F

1 9

O 2 3O 2 4

O 2 5

O 2 6 O 2 7 O 2 8

4 4

I35 I36 I37

I38 I39 I40

L 5 0 L 5 1

K 5 5 K 5 6 K 5 7

K 52 K 5 3 K 5 4

M 5 8 M 5 9 M 6 0

JL

C

E

1 2

A 1

A 4

A 2

A 5

A 3

A 6

N

6 1

N

6 2

E

2 1

E

2 2




Autologic tool: >Start> Towbar> select Citroen or Peugeot>Trailer module>Edit Trailer module status> Fitted







Trailer Stability ProgramIf TSP is available, the module will enable it

Documents

Smart Can Data