View
217
Download
2
Embed Size (px)
Citation preview
Soil Water Content Soil Moisture Content
Water that may be evaporated from soil by heating at 1050C to a constant weight
Gravimetric moisture content (w) =mass of water evaporated (g)
mass of dry soil (g)
Volumetric moisture content () =volume of water evaporated (cm3)
volume of soil (cm3)
= w *bulk density of soil
density of water g
cm
cm
g
g
g
cmgcmg
g
g
cm
cm 3
3
3
3
3
3
Bulk density of soil () =mass of dry soil (g)
volume of soil (cm3)
Example: A soil is sampled by a cylinder measuring 7.6 cm in diameter and 7.6 cm length. Calculate gravimetric and volumetric water contents, and wet and dry bulk densities using the following data:
1. Weight of empty cylinder = 300 g
2. Weight of cylinder + wet soil = 1000 g
3. Weight of cylinder + oven dry (1050C) soil = 860 g
Volume of cylinder = *r2*h = 3.14*(7.6/2)2*7.6 = 345 cm3
Weight of wet soil = 1000 – 300 = 700 g
Weight of dry soil = 860 – 300 = 560 g
Dry bulk density = 560/345 = 1.62 g cm-3
Gravimetric moisture content = (700-560)/560 = 0.25 or 25%
Volumetric moisture content = *w = 1.62*0.25 = 0.41 or 41%
Know how to do these calculations for quiz on Friday
Calculating dry soil weight basis of samples for analysis
Weigh drying pan, moist soil subsample + pan,
Oven dry the subsample at 105C for 24 hr,
Weigh the dried soil + pan.
Calculate the moisture content (w):
w = (g moist soil – g dry soil)/(g dry soil – pan)
Rearrange the eqn to solve for dry soil wt.
Dry soil wt = g moist soil / (1 + w)
Methods for measuring soil water content
Direct method (Gravimetric)
Indirect methods(need to calibrate)
Electrical properties
Radiation technique
Acoustic method
Thermal properties
Chemical methods
Electrical Conductance
Dielectric constant
-Neutron scattering- ray attenuation
- Gypsum blocks- Nylon blocks- Change in conductance
TDR
Principles underlying different methods of assessment of soil water content
Direct
Gravimetric: evaporating water at 1050C (be able to do the calc’ns)
Indirect
Neutron scattering:Thermalization Time domain reflectrometry:
Dielectric constant
Water Content
In-direct:
Watermark (granular matrix sensor), gypsum block
Direct: Tensiometer
Soil Water (matric) Potential
Gently tap a tube into the soil to take an undisturbed sample from the center of
the effective root zone.
Trim the soil at each end of the tube to the tube length so that the soil occupies the
exact tube volume.
Calibration for moisture content• Measure and weigh the tube• Weigh the field moist soil + tube• Oven dry the soil from the tube• Calculate:
W = g water/g dry soil = (wet – dry) / dry soil
Db = g dry soil / cm3 volume soil
Θ = (W x Db) / Dw
• Compare lab moisture content to field measurements
• For water potential, compare water retention curves derived in lab using pressure plates.
Water retention curves: Water content vs pressure or tension
Note: clay holds more water at a specific water potential than sand or loam;
Water is held tighter at a given water content in clay than in sand.
Structure is predominant at low potentials; as soil dries out, texture is more important
Effect of structure on water flow
www.soils.umn.edu/.../soil2125/doc/s7chp3.htm
Saturated flow
where Q is volume of water in time (t)
A is area of cross section
Ksat is saturated hydraulic conductivity of soil (how fast water moves)
L is length of column
Ψ is the water potential at points 1 and 2
Ksat = Q/A x L/(Ψ1 - Ψ2)
http://soils.usda.gov/technical/technotes/note6fig1.jpg
Flux can be thought of as water flowing from a hose. The flux is the rate of water discharged by the hose, divided by the cross-sectional area of the hose.
Saturated flow in soils
• The pores are full of water and matric potential is considered to be negligible
because at least some of the water is a long distance from solid surfaces
• Under these conditions, flow is: Rapid - moving through large pores Driven by gravity and sometimes
Hydrostatic pressure if water is ponded
Unsaturated flow – most common in soils• Occurs along soil surfaces, not through large pores.• Driven by matric forces that are much stronger than
gravity.Gravity is not sufficiently strong to exert a significant influence on unsaturated flow because much of the soil water adheres to solid surfaces.
• Unsaturated flow is slow. • Even though the driving force is usually greater than for
saturated flow, the resistance to flow is enormous. • Water will flow toward a lower (more negative) potential
regardless of direction (up, down, laterally). In other words it will flow towards: drier medium salty solution finer texture (small pores)