Solenoid Operated Pinch Valves - Cole-Parmer 2-way 3-way Dual 3-way Choice of tubing materials. Bio-Chem Fluidics offers two high-purity medical grade tubing materials for pinch valves:

……………. Solenoid Operated

Pinch Valves

……………

2

INDEX

Page 3 Pinch Valve General Information

Page 7 Silicone and C-Flex® Tubing Options Spare tubing part numbers

Page 9 Pinch Valve Selection Guide

Page 10 Pinch Valve Part Numbering Conventions

Page 12 075-series Pinch Valves Pinch valves for 1/16” (1.6mm) inner diameter tubing and smaller.

Page 18 100-series Pinch Valves Pinch valves for 1/4” (6.3mm) inner diameter tubing and smaller.

Page 26 Position Feedback Sensor

Page 27 CoolCube Hit-and-Hold Circuit

Page 28 Controller

Page 29 Fittings and Connectors

Page 32 Mounting Accessories

3

PINCH VALVE GENERAL INFORMATION What is a Pinch Valve?

The Bio-Chem Fluidics pinch valve is a solenoid-operated device. It is designed for opening and closing tubing to achieve controlled fluid flow. When the solenoid is energized, the valve plunger is retracted. This either opens the tubing (normally closed configuration) or closes the tubing (normally open configuration). A valve in the 3-way configuration has both a normally open and a normally closed flow path, which are operated simultaneously. When the solenoid is de-energized, a spring returns the tubing back to its original open or closed position.

Why a Pinch Valve rather than an Isolation Valve?

Compared to an isolation valve that uses a diaphragm, the pinch valve has several distinctive advantages: An unobstructed flow path with minimal pressure drop. Resistant to damage from particulates in the fluid stream. Ease of changing the wetted surfaces (i.e. the tubing for pinch valves) between operations. Easy sterilization of fluid path. No dead volume inside the valve.

FEATURES OF BIO-CHEM VALVE™ PINCH VALVES Choice of tubing configurations.

The pinch valves are supplied with tubing already inserted in the valve: 2-way valves: one 12-inch (30cm) tubing section. 3-way valves: two 6-inch (15cm) tubing sections joined by a “Y” connector.

Dual tubing configurations (i.e. two tubes being operated simultaneously) are offered for smaller tubing sizes. Multi-tube pinch valves with 4, 6 or 8 tubes and normally open operation are also available.

4

2-way

3-way

Dual 3-way

Choice of tubing materials.

Bio-Chem Fluidics offers two high-purity medical grade tubing materials for pinch valves: Platinum cured silicone tubing. C-Flex® tubing.

These tubing options have been specifically developed to withstand the rigors of usage with pinch valves. The tubing will not stick shut even after prolonged closure. Excellent tubing memory characteristics permit unencumbered flow when the valve is in the open position. In combination with the Bio-Chem Valve pinch valves, both tubing options are rated for over 300,000 cycles. It is also possible to use the pinch valves with tubing other than that supplied by Bio-Chem Fluidics. In that case, Bio-Chem Fluidics will adjust the valve settings to meet the exact requirements of the customer’s tubing.

Stroke set for each individual valve.

The stroke (i.e. the travel between the open and closed positions) is individually set and tested for each pinch valve. Through this process, we ascertain: ~95% full flow in the open position. No leakage in the closed position at rated

pressures. Efficient valve operation with minimal

power usage and heat generation. Maximum tubing life.

Easy tube insertion.

The tubing entry area of the valve body is contoured to guide the tubing into its seat.

Tubing securely seated.

The tubing is securely seated in a groove. The gap between the valve plunger and the valve’s anvil is slightly smaller than the tubing’s outer diameter. The tubing is held in place during operation without need for mechanical locking features. Fluid flow and pressure drop are minimally affected, achieving around 95% of full flow given the nominal tubing inner diameter.

5

Long life cycles.

Bio-Chem Valve™ pinch valves are designed to last for a minimum of 2 million open-and close cycles. By choosing optional alternative body and plunger materials, the valve life can be extended even further. Thanks to the precise stroke adjustment performed on each valve, we also optimize the tubing life. Both the silicone and the C-Flex® tubing are rated for over 300,000 life cycles.

Continuous duty.

Bio-Chem Valve™ pinch valves can remain in the fully energized state indefinitely without damage to the valve or the tubing.

Low power consumption and minimal heat generation.

The pinch valves’ efficient construction permits the use of low wattage solenoid coils, ranging from 2.8 Watt for 075-series valves to 8.0 Watt for 150-series valves. Heat generation is correspondingly low. Both power usage and heat generation can be lowered further by stepping down the voltage after actuation. With most of the pinch valves, voltage reduction of 66% is possible, reducing power consumption by 89%.

Optional features, particularly for medical applications.

Override button for manual opening or closing of tubing. This feature provides flow control in the case of power loss. It also facilitates tubing changes, especially when working with hard tubing, such as Tygon®.

Pre-configured, factory-installed mounting flanges. The flanges can be fixed so as to be on the inside or the outside of the bulkhead. The customer can choose the orientation of the mounting holes vis-à-vis the tubing. The flanges are securely fixed to ensure the valves permanent position despite of frequent manipulation and tubing changes.

“Quiet” operation. Through the use of noise-dampening materials on internal valve components, the noise generated at actuation of 075-series and 100-series pinch valves is reduced dramatically.

6

The noise level drops from approximately 72 dB to 52dB. This feature is recommended in noise-sensitive environments, such as hospitals. Position feedback sensor. An infra-red optical sensor can be factory-mounted on the pinch valve. The sensor detects the position of the valve pusher assembly. It sends an electrical signal back to the controller confirming the open or closed valve position. PPS body material. For applications where the valve body may come into contact with corrosive liquids, chemically resistant glass-filled PPS material is available for the valve body and plunger. Use of the PPS body extends the valve life to 5 million cycles.

7

PINCH VALVE TUBING

A. Platinum-cured silicone tubing

1. Test Standards. The Bio-Chem Valve silicone tubing is tested in accordance to the standards set by the United States Pharmacopoeia National Formulary XVII, 1990, Class VI Biological Test for Plastics. It is FDA Masterfile listed (MAF 819).

2. Durability. This tubing has been selected for use with pinch valves. Platinum curing performed on the tubing during the extrusion process imparts superior strength and durability. The byproduct of this process, ethanol, is completely removed. The tubing has a low compression set and will not stick shut even after prolonged periods in the closed position. Excellent memory characteristics ensure full opening and unencumbered flow. The silicone tubing is rated for 300,000 pinch valve cycles.

3. Sterilization. The silicone tubing can be sterilized through steam autoclaving, boiling, dry heat, steam, and gamma radiation.

4. Gas permeability. Silicone tubing has a poor gas permeability rating.

Besides being already installed in the Bio-Chem Fluidics pinch valves, silicone tubing is also available in 50-foot (15-meter) coils. The coils can be ordered under the part numbers listed below:

Diameter Pressure Part number Inner Outer Minimum Maximum Length

10025-10S 0.010” / 0.25mm 0.093” / 2.36mm vacuum 30 psi / 2.0 bar 50 ft / 15m10025-23S 0.023”/ 0.58mm 0.093” / 2.36mm vacuum 20 psi / 1.3 bar 50 ft / 15m10025-01S 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 50 ft / 15m10025-50S 1/20” / 1.27mm 0.134” / 3.40mm vacuum 15 psi / 1.0 bar 50 ft / 15m10025-02S 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 50 ft / 15m10025-03S 1/16” / 1.59mm 3/16” / 4.76mm vacuum 25 psi / 1.6 bar 50 ft / 15m10025-04S 3/16” / 4.76mm 1/4” / 6.35mm 0 psi / 0 bar 10 psi / 0.6 bar 50 ft / 15m10025-05S 1/8” / 3.18mm 1/4” / 6.35mm vacuum 20 psi / 1.3 bar 50 ft / 15m10025-06S 1/4” / 6.35mm 3/8” / 9.52mm 0 psi / 0 bar 10 psi / 0.6 bar 50 ft / 15m10025-07S 5/16” / 7.94mm 7/16” / 11.1mm 0 psi / 0 bar 10 psi / 0.6 bar 50 ft / 15m

8

B. C-Flex® tubing

1. Test Standards. The C-Flex® tubing used on the Bio-Chem Valve pinch valves is tested in accordance to the standards set by the United States Pharmacopoeia National Formulary XVII, 1990, Class VI Biological Test for Plastics. It is FDA Masterfile listed.

2. Material. The C-Flex® tubing material is a thermoplastic elastomer based on styrene-ethylene-butylene. It does not contain leachable plasticizers.

3. Chemical compatibility. C-Flex® can be used with many acids and alkalis. It is not recommended for use with oils and organic solvents.

4. Durability. This tubing has been selected for use with pinch valves. The tubing has a low compression set and will not stick shut even after prolonged periods in the closed position. Good memory characteristics ensure full opening and unencumbered flow. The C-Flex® tubing is rated for 200,000 pinch valve cycles.

5. Sterilization. The C-Flex® tubing can be sterilized through steam autoclaving, ethylene oxide (ETO), and gamma radiation.

6. Gas permeability. C-Flex® tubing has a fair gas permeability rating. It has lower gas permeability than silicone.

Besides being already installed in the Bio-Chem Fluidics pinch valves, C-Flex® tubing is also available in 50-foot (15-meter) coils. The coils can be ordered under the part numbers listed below:

Diameter Pressure Part number Inner Outer Minimum Maximum Length

10025-23B 0.023”/ 0.58mm 0.093” / 2.36mm vacuum 20 psi / 1.3 bar 50 ft / 15m10025-01B 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 50 ft / 15m10025-02B 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 50 ft / 15m10025-03B 1/16” / 1.59mm 3/16” / 4.76mm vacuum 25 psi / 1.6 bar 50 ft / 15m10025-05B 1/8” / 3.18mm 1/4” / 6.35mm vacuum 20 psi / 1.3 bar 50 ft / 15m10025-06B 1/4” / 6.35mm 3/8” / 9.52mm 0 psi / 0 bar 10 psi / 0.6 bar 50 ft / 15m10025-07B 5/16” / 7.94mm 7/16” / 11.1mm 0 psi / 0 bar 10 psi / 0.6 bar 50 ft / 15m

9

PINCH VALVE SELECTION GUIDE

A. Valves with Bio-Chem Valve silicone or C-Flex® tubing installed

1. Select the tubing material – either silicone or C-Flex®. (See page 7 for additional information about these tubing material options.)

2. Identify your required valve specifications among the following features: a. Tubing internal diameter. b. Flow configuration – normally open, normally closed, three-way or multi-tube. c. Minimum and maximum pressure parameters.

3. Determine the valve type by looking up your combination of valve specifications in the tables below.

Silicone Tubing Flow Configuration Internal

diameter 2-Way NC

2-Way NO

3-Way 2 or 3-Way dual tube

Min Pressure

Max Pressure

Valve Type

0.010” / 0.25mm √ √ vacuum 30 psi / 2.0 bar

0.023”/ 0.58mm √ √ √ vacuum 20 psi / 1.3 bar

1/32” / 0.79mm √ √ √ vacuum 15 psi / 1.0 bar

1/20” / 1.27mm √ √ √ vacuum 15 psi / 1.0 bar 1/16” / 1.59mm √ √ √ 0 psi / 0 bar 15 psi / 1.0 bar

075P pg 11

1/32” / 0.79mm √ √ √ √ vacuum 25 psi / 1.6 bar

1/16” / 1.59mm √ √ √ √ vacuum 25 psi / 1.6 bar

1/8” / 3.18mm √ √ √ vacuum 20 psi / 1.3 bar

3/16” / 4.76mm √ √ √ 0 psi / 0 bar 10 psi / 0.6 bar

1/4” / 6.35mm √ √ 0 psi / 0 bar 10 psi / 0.6 bar

100P pg 12

1/4” / 6.35mm √ 0 psi / 0 bar 10 psi / 0.6 bar 150P pg 14

1/32” / 0.79mm Multi-tube

√ 0 psi / 0 bar 15 psi / 1.0 bar 108P pg 15

C-Flex® Tubing

Flow Configuration Internal diameter 2-Way

NC 2-Way

NO 3-Way 2 or 3-Way

dual tube

Min Pressure

Max Pressure

Valve Type

0.023”/ 0.58mm √ √ √ vacuum 20 psi / 1.3 bar

1/32” / 0.79mm √ √ √ vacuum 15 psi / 1.0 bar 1/16” / 1.59mm √ √ √ 0 psi / 0 bar 15 psi / 1.0 bar

075P pg 11

1/32” / 0.79mm √ √ √ √ vacuum 25 psi / 1.6 bar

1/16” / 1.59mm √ √ √ √ vacuum 25 psi / 1.6 bar

1/8” / 3.18mm √ √ √ vacuum 20 psi / 1.3 bar

1/4” / 6.35mm √ √ 0 psi / 0 bar 10 psi / 0.6 bar

100P pg 12

1/4” / 6.35mm √ 0 psi / 0 bar 10 psi / 0.6 bar 150P pg 14

1/32” / 0.79mm Multi-tube

√ 0 psi / 0 bar 15 psi / 1.0 bar 108P pg 15

10

4. Turn to the appropriate page and select the valve based on the specification identified above and

additional attributes of your choice: Voltage(12 or 24 VDC) “Quiet” feature (optional) Mounting holes (optional) Mounting flange (optional) Position feedback sensor (optional) Manual override button (optional)

B. Valves for silicone or C-Flex® tubing to be installed by the customer

The Bio-Chem Fluidics valves can be purchased without the tubing installed. The customer can then order the tubing separately and add the tubing at a later time.

For this option, follow the same valve selection process as outlined above. Then follow the part number convention process for the determining the valve part number. C. Valves for customer-specific tubing

If the customer intends to use the pinch valves with tubing other than Bio-Chem Fluidics-supplied silicone or C-Flex® tubing, this requirement can be accommodated. The customer should provide a sample of the tubing to Bio-Chem Fluidics, who will select the appropriate valve size and adjust the stroke and force settings to match the tubing diameter and durometer.

Bio-Chem Fluidics will assign a special part number to this valve.

11

PINCH VALVE PART NUMBER CONVENTIONS

A. Single or dual tube pinch valves

The part numbers are constructed according to the following pattern:

1. Shell size corresponds to the diameter of the solenoid shell. Available sizes are 075P (3/4” diameter), 100P (1.0” diameter) and 150P (1.5” diameter).

2. Flow path options are “2” (2-way), “3” (3-way), “D2” (dual 2-way), and “D3” (dual 3-way).

3. Flow configuration options are “NC” (normally closed), “NO” (normally open), and “MP” (3-way with one port normally open and the other port normally closed).

4. Voltages offered are “12” (12 Vdc) and “24” (24 Vdc).

5. Tube size designators are assigned according to the following table:

Designator Inner diameter Outer diameter Silicone C-Flex® -10 0.010” / 0.25mm 0.093” / 2.36mm √

-23 0.023”/ 0.58mm 0.093” / 2.36mm √ √

-01 1/32” / 0.79mm 3/32” / 2.36mm √ √

-50 1/20” / 1.27mm 0.134” / 3.40mm √

-02 1/16” / 1.59mm 1/8” / 3.18mm √ √

-03 1/16” / 1.59mm 3/16” / 4.76mm √ √

-04 3/16” / 4.76mm 1/4” / 6.35mm √

-05 1/8” / 3.18mm 1/4” / 6.35mm √ √

-06 1/4” / 6.35mm 3/8” / 9.52mm √ √

6. Tubing material options are “S” (silicone) and “B” (C-Flex®). In case the valve is to be delivered without tubing, the material designating letter is replaced by a hash mark (“#“). The tubing size designator must still be indicated as before.

7. Valve options can be designated by the following letters, which should be added in the sequence indicated below:

4 – PPS body material. Q – “quiet” valves, available for 075P and 100P normally closed valves. M – mounting holes situated on the bottom of the valve body. F – position feedback sensor. K – manual override button, available for 075P and 100P valves without dual tubing. When the manual override button is chosen, the “M” for mounting holes cannot be selected. L – factory-installed mounting flange, available for 075P and 100P valves. The flanges will be installed at 90º to the tubing path. When an option is not selected, the corresponding part number position is simply left blank.

12

075P SERIES PINCH VALVES

For use with soft-walled tubing with inner diameters from 0.010”/0.25mm to 1/16”/1.59mm.

Features of standard 075P series pinch valves.

Continuous duty solenoid operated valve. Can remain fully energized for indefinite time period.

Valve life above 2 million cycles. Precise stroke and closing force setting

to protect tubing and extend valve life. Chemically resistant PPS plunger and

ASA/PC body materials. 15-inch (38cm) lead wires. Low power consumption (3.5 Watt or

less) and minimal heat generation.

A. Two-Way Normally closed valves

Part No. Inner diameter Outer diameter Min pressure Max pressure Power at 21ºC

075P2NC12-10S 0.010” / 0.25mm 0.093” / 2.36mm vacuum 30 psi / 2.0 bar 3.5 Watt 075P2NC12-23S 0.023”/ 0.58mm 0.093” / 2.36mm vacuum 20 psi / 1.3 bar 2.8 Watt 075P2NC12-01S 98302-00

1/32” / 0.79mm already switched

3/32” / 2.36mm vacuum 15 psi / 1.0 bar 2.8 Watt

075P2NC24-01S 98302-10


3/32” / 2.36mm vacuum 15 psi / 1.0 bar 2.8 Watt 24 VDC

075P2NC12-50S 1/20” / 1.27mm 0.134” / 3.40mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P2NC12-02S 98302-02


1/8” / 3.18mm 0 psi / 0 bar 15 psi / 1.0 bar 2.8 Watt

075P2NC24-02S 98302-12


1/8” / 3.18mm 0 psi / 0 bar 15 psi / 1.0 bar 2.8 Watt 24 VDC


075P2NC12-10B 0.010” / 0.25mm 0.093” / 2.36mm vacuum 30 psi / 2.0 bar 3.5 Watt

12 VDC valves with silicone tubing. 12-inch (30cm) strip of silicone tubing is installed in the valve.

NOTE: For 24 VDC, replace 075P2NC12 with 075P2NC24 in any of the part numbers listed.

12 VDC valves with C-Flex® tubing. 12-inch (30cm) strip of C-Flex® tubing is installed in the valve.

3-way valve

Plunger

Body

Solenoid shell

Lead wires

2-way valve

13

075P2NC12-23B 0.023”/ 0.58mm 0.093” / 2.36mm vacuum 20 psi / 1.3 bar 2.8 Watt 075P2NC12-01B 1/32” / 0.79mm 3/32” / 2.36mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P2NC12-50B 1/20” / 1.27mm 0.134” / 3.40mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P2NC12-02B 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 15 psi / 1.0 bar 2.8 Watt

B. Two-Way Normally open valves

Part No. Gapped for inner diameter

Gapped for outer diameter

Min pressure Max pressure Power at 21ºC

075P2NC12-10# 0.010” / 0.25mm 0.093” / 2.36mm vacuum 30 psi / 2.0 bar 3.5 Watt 075P2NC12-23# 0.023”/ 0.58mm 0.093” / 2.36mm vacuum 20 psi / 1.3 bar 2.8 Watt 075P2NC12-01# 1/32” / 0.79mm 3/32” / 2.36mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P2NC12-50# 1/20” / 1.27mm 0.134” / 3.40mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P2NC12-02# 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 15 psi / 1.0 bar 2.8 Watt


075P2NO12-10S 0.010” / 0.25mm 0.093” / 2.36mm vacuum 30 psi / 2.0 bar 3.5 Watt 075P2NO12-23S 0.023”/ 0.58mm 0.093” / 2.36mm vacuum 20 psi / 1.3 bar 2.8 Watt 075P2NO12-01S 98302-20

1/32” / 0.79mm switch Apr 2010


075P2NO24-01S 98302-30

1/32” / 0.79mm switch Apr 2010


075P2NO12-50S 1/20” / 1.27mm 0.134” / 3.40mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P2NO12-02S 98302-22

1/16” / 1.59mm switch Apr 2010


075P2NO12-02S 98302-32

1/16” / 1.59mm switch Apr 2010



075P2NO12-10B 0.010” / 0.25mm 0.093” / 2.36mm vacuum 30 psi / 2.0 bar 3.5 Watt 075P2NO12-23B 0.023”/ 0.58mm 0.093” / 2.36mm vacuum 20 psi / 1.3 bar 2.8 Watt 075P2NO12-01B 1/32” / 0.79mm 3/32” / 2.36mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P2NO12-50B 1/20” / 1.27mm 0.134” / 3.40mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P2NO12-02B 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 15 psi / 1.0 bar 2.8 Watt

12 VDC valves without factory-installed tubing. Valves can be used with Bio-Chem Fluidics supplied silicone or C-Flex® tubing.

NOTE: For 24 VDC, replace 075P2NO12 with 075P2NO24 in any of the part numbers listed.



14

C. Three-way valves (one port normally open, other port normally closed)




075P2NO12-10# 0.010” / 0.25mm 0.093” / 2.36mm vacuum 30 psi / 2.0 bar 3.5 Watt 075P2NO12-23# 0.023”/ 0.58mm 0.093” / 2.36mm vacuum 20 psi / 1.3 bar 2.8 Watt 075P2NO12-01# 1/32” / 0.79mm 3/32” / 2.36mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P2NO12-50# 1/20” / 1.27mm 0.134” / 3.40mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P2NO12-02# 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 15 psi / 1.0 bar 2.8 Watt


075P3MP12-23S 0.023”/ 0.58mm 0.093” / 2.36mm vacuum 20 psi / 1.3 bar 2.8 Watt 075P3MP12-01S 98302-40

1/32” / 0.79mm switch July 2010


075P3MP24-01S 98302-48

1/32” / 0.79mm switch July 2010


075P3MP12-50S 1/20” / 1.27mm 0.134” / 3.40mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P3MP12-02S 98302-42

1/16” / 1.59mm switch July 2010


075P3MP24-02S 98302-50

1/16” / 1.59mm switch July 2010



075P3MP12-23B 0.023”/ 0.58mm 0.093” / 2.36mm vacuum 20 psi / 1.3 bar 2.8 Watt 075P3MP12-01B 1/32” / 0.79mm 3/32” / 2.36mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P3MP12-50B 1/20” / 1.27mm 0.134” / 3.40mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P3MP12-02B 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 15 psi / 1.0 bar 2.8 Watt


NOTE: For 24 VDC, replace 075P3MP12 with 075P3MP24 in any of the part numbers listed.

12 VDC valves with silicone tubing. Two 6-inch (15cm) strips of silicone tubing joined by ‘Y’ connector installed in the valve.

12 VDC valves with C-Flex® tubing. Two 6-inch (15cm) strips of C-Flex® tubing joined by ‘Y’ connector installed in the valve.

15

D. Options 1. Glass-filled PPS body material (suffix = “4”). Changing the body material from ASA/PC to PPS

provides two advantages: a. Enhanced chemical resistance in the case of spills onto the body or when using aggressive

cleaning agents on the valves. b. Longer cycle life, extending the valve life cycles from 2 million to 5 million.

2. “Quiet” operation (suffix = “Q”). Implementing the “quiet” option reduces the valve noise level from about 72 dB to about 52 dB. The “quiet” option is available for: a. 075P2NC-way normally closed valves. b. 075P2NO-way normally open valves. The “quiet” option cannot be used on 075P3MP three-way valves. The noise level of the 3-way valves is inherently attenuated by tubing dampening the motion in both directions.

3. Mounting holes (suffix = “M”) situated on the bottom of the valve body (i.e. the plastic). The dimensions are as follows: a. A (thread) = #2-56 b. B = 0.50 inches / 12.7mm center-to-center c. C = 0.125 inches / 3.2mm The mounting holes cannot be used in combination with the manual override button.

4. Position feedback sensor (suffix = “F”). The feedback sensor can be mounted on 075P pinch valves in the normally closed and the three-way configurations. (Please see page XX for details about this option.)

5. Manual override button (suffix = “K”). The manual override button is available for all 2-way and 3-way valve configurations. Its uses include: a. Flow control for emergencies during electric power loss. b. To facilitate tubing changes.




075P2NO12-23# 0.023”/ 0.58mm 0.093” / 2.36mm vacuum 20 psi / 1.3 bar 2.8 Watt 075P2NO12-01# 1/32” / 0.79mm 3/32” / 2.36mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P2NO12-50# 1/20” / 1.27mm 0.134” / 3.40mm vacuum 15 psi / 1.0 bar 2.8 Watt 075P2NO12-02# 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 15 psi / 1.0 bar 2.8 Watt


16

6. Factory-installed mounting flange (suffix = “L”). The mounting flanges are available for all 075P pinch valve configurations. They will be installed at a 90º angle to the tubing with the orientation to the outside of the bulkhead. a. 30% glass-filled polypropylene material provides secure

fit. b. Can be cleaned with alcohol, bleaches and other

cleaning agents. c. White color. d. Distance between mounting hole centers = 1.25” /

3.2cm. e. The flanges can be installed at angles other than 90º to

the tubing and/or with orientation to the inside of the bulkhead upon request.

This mounting flange can be purchased as a stand-alone item under part number MFP-075. Please see page XX for details.

E. “Hit and Hold” voltage reduction Within 100 ms of valve actuation, the voltage required to hold the valve in position can be reduced. The voltage step-down results in the dual benefits of power conservation and heat reduction. The amount of the voltage reduction possible is 66% (i.e. 24 Vdc to 8 Vdc or 12 Vdc to 4 Vdc) for all 075P pinch valves that do not incorporate the “quiet” feature. This results in a power usage / heat generation drop of 89%.

The 66% voltage reduction can be accomplished using the Bio-Chem Fluidics CoolCube-R hit-and-hold circuit. Please see page XX for details.

For the 075P pinch valves with the “quiet” feature, voltage can be reduced by 33% (i.e. 24 Vdc to 16 Vdc and 12 Vdc to 8 Vdc) after 100 ms for a power usage drop of 55%.

F. Dimensions

075P2NC Normally Closed 2-Way Pinch Valve

17

075P2NC Normally Open 2-Way Pinch Valve

075P3MP 3-Way Pinch Valve

18

100P SERIES PINCH VALVES

For use with soft-walled tubing with inner diameters from 1/32” / 0.79mm to 1/4” / 6.35mm.

Features of standard 100P series pinch valves.

Continuous duty solenoid operated valve. Can remain fully energized for indefinite time period.

Valve life above 2 million cycles. Precise stroke and closing force setting to

protect tubing and extend valve life. Chemically resistant PPS plunger and

ASA/PC body materials. 15-inch (38cm) lead wires. Low power consumption (mostly 4.0 Watt)

and minimal heat generation.

A. Two-Way Normally closed valves


100P2NC12-01S 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 100P2NC12-02S 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt 100P2NC12-03S 98302-04

1/16” / 1.59mm switch July 2010


100P2NC24-03S 98302-14

1/16” / 1.59mm switch July 2010


100P2NC12-04S 3/16” / 4.76mm 1/4” / 6.35mm 0 psi / 0 bar 10 psi / 0.6 bar 4.0 Watt 100P2NC12-05S 98302-06

1/8” / 3.18mm switch July 2010


100P2NC24-05S 98302-16



100P2NC12-06S 98302-10



100P2NC24-06S 98302-18



Lead wires

Solenoid shell

Plunger

Body

2-way valve 3-way valve


NOTE: For 24 VDC, replace 100P2NC12 with 100P2NC24 in any of the part numbers listed.

19

B. Two-Way Normally open valves


100P2NC12-01B 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 100P2NC12-02B 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt 100P2NC12-03B 1/16” / 1.59mm 3/16” / 4.76mm vacuum 25 psi / 1.6 bar 4.0 Watt 100P2NC12-04B 3/16” / 4.76mm 1/4” / 6.35mm 0 psi / 0 bar 10 psi / 0.6 bar 4.0 Watt 100P2NC12-05B 1/8” / 3.18mm 1/4” / 6.35mm vacuum 20 psi / 1.3 bar 4.0 Watt 100P2NC12-06B 1/4” / 6.35mm 3/8” / 9.52mm 0 psi / 0 bar 10 psi / 0.6 bar 8.0 Watt




100P2NC12-01# 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 100P2NC12-02# 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt 100P2NC12-03# 1/16” / 1.59mm 3/16” / 4.76mm vacuum 25 psi / 1.6 bar 4.0 Watt 100P2NC12-04# 3/16” / 4.76mm 1/4” / 6.35mm 0 psi / 0 bar 10 psi / 0.6 bar 4.0 Watt 100P2NC12-05# 1/8” / 3.18mm 1/4” / 6.35mm vacuum 20 psi / 1.3 bar 4.0 Watt 100P2NC12-06# 1/4” / 6.35mm 3/8” / 9.52mm 0 psi / 0 bar 10 psi / 0.6 bar 8.0 Watt



NOTE: For 24 VDC, replace 100P2NO12 with 100P2NO24 in any of the part numbers listed.

20


100P2NO12-01S 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 100P2NO12-02S 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt 100P2NO12-03S 98302-24

1/16” / 1.59mm switch April 2010


100P2NO24-03S 98302-34



100P2NO12-04S 3/16” / 4.76mm 1/4” / 6.35mm 0 psi / 0 bar 10 psi / 0.6 bar 4.0 Watt 100P2NO12-05S 98302-26



100P2NO24-05S 98302-36



100P2NO12-06S 98302-28



100P2NO24-06S 98302-38




100P2NO12-01B 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 100P2NO12-02B 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt 100P2NO12-03B 1/16” / 1.59mm 3/16” / 4.76mm vacuum 25 psi / 1.6 bar 4.0 Watt 100P2NO12-04B 3/16” / 4.76mm 1/4” / 6.35mm 0 psi / 0 bar 10 psi / 0.6 bar 4.0 Watt 100P2NO12-05B 1/8” / 3.18mm 1/4” / 6.35mm vacuum 20 psi / 1.3 bar 4.0 Watt 100P2NO12-06B 1/4” / 6.35mm 3/8” / 9.52mm 0 psi / 0 bar 10 psi / 0.6 bar 8.0 Watt



21




100P2NC12-01# 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 100P2NC12-02# 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt 100P2NC12-03# 1/16” / 1.59mm 3/16” / 4.76mm vacuum 25 psi / 1.6 bar 4.0 Watt 100P2NC12-04# 3/16” / 4.76mm 1/4” / 6.35mm 0 psi / 0 bar 10 psi / 0.6 bar 4.0 Watt 100P2NC12-05# 1/8” / 3.18mm 1/4” / 6.35mm vacuum 20 psi / 1.3 bar 4.0 Watt 100P2NC12-06# 1/4” / 6.35mm 3/8” / 9.52mm 0 psi / 0 bar 10 psi / 0.6 bar 8.0 Watt

C. Three-way valves (one port normally open, other port normally closed)


100P3MP12-01S 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 100P3MP12-02S 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt 100P3MP12-03S 98302-44

1/16” / 1.59mm switch July 2010


100P3MP24-03S 98302-52

1/16” / 1.59mm switch July 2010


100P3MP12-04S 3/16” / 4.76mm 1/4” / 6.35mm 0 psi / 0 bar 10 psi / 0.6 bar 8.0 Watt 100P3MP12-05S 98301-46



100P3MP24-05S 98301-54




100P3MP12-01B 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 100P3MP12-02B 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt 100P3MP12-03B 1/16” / 1.59mm 3/16” / 4.76mm vacuum 25 psi / 1.6 bar 8.0 Watt 100P3MP12-04B 3/16” / 4.76mm 1/4” / 6.35mm 0 psi / 0 bar 10 psi / 0.6 bar 8.0 Watt 100P3MP12-05B 1/8” / 3.18mm 1/4” / 6.35mm vacuum 20 psi / 1.3 bar 8.0 Watt


NOTE: For 24 VDC, replace 100P3MP12 with 100P3MP24 in any of the part numbers listed.

12 VDC valves with silicone tubing. Two 6-inch (15cm) strips of silicone tubing joined by ‘Y’ connector installed in the valve.

12 VDC valves with C-Flex® tubing. Two 6-inch (15cm) strips of C-Flex® tubing joined by ‘Y’ connector installed in the valve.

22




100P3MP12-01# 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 100P3MP12-02# 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt 100P3MP12-03# 1/16” / 1.59mm 3/16” / 4.76mm vacuum 25 psi / 1.6 bar 8.0 Watt 100P3MP12-04# 3/16” / 4.76mm 1/4” / 6.35mm 0 psi / 0 bar 10 psi / 0.6 bar 8.0 Watt 100P3MP12-05# 1/8” / 3.18mm 1/4” / 6.35mm vacuum 20 psi / 1.3 bar 8.0 Watt

D. Valves with Dual Tubing For use with soft-walled tubing with inner diameters of1/32” / 0.79mm and 1/16” / 1.59mm.

Features of standard 100PD series dual-tubing pinch valves are identical to those of single-tubing pinch valves except:

The body and plunger material is Acetal. There are two sets of tubing in every

valve.

Configuration Part No. Inner diameter Outer diameter Min pressure

Max pressure Power at 21ºC

100PD2NC12-01S 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 2-Way normally closed 100PD2NC12-02S 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt

100PD2NO12-01S 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 2-Way normally open 100PD2NO12-02S 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt

100PD3MP12-01S 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 8.0 Watt 3-Way

100PD3MP12-02S 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 8.0 Watt


NOTE: For 24 VDC, replace 100PD---12 with 100PD---24 in any of the part numbers listed.

12 VDC valves with silicone tubing. 2-Way: 12-inch (30cm) strip of silicone tubing is installed in the valve. 3-Way: Two 6-inch (15cm) strips of silicone tubing joined by ‘Y’ connector installed in the valve.

23

Configuration Part No. Inner diameter Outer diameter Min

pressure Max pressure Power at

21ºC 100PD2NC12-01B 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 2-Way normally

closed 100PD2NC12-02B 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt 100PD2NO12-01B 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 2-Way normally

open 100PD2NO12-02B 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt 100PD3MP12-01B 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 8.0 Watt

3-Way 100PD3MP12-02B 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 8.0 Watt

Configuration Part No. Inner diameter Outer diameter Min

pressure Max pressure Power at

21ºC 100PD2NC12-01# 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 2-Way normally

closed 100PD2NC12-02# 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt 100PD2NO12-01# 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 4.0 Watt 2-Way normally

open 100PD2NO12-02# 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 4.0 Watt 100PD3MP12-01# 1/32” / 0.79mm 3/32” / 2.36mm vacuum 25 psi / 1.6 bar 8.0 Watt

3-Way 100PD3MP12-02# 1/16” / 1.59mm 1/8” / 3.18mm 0 psi / 0 bar 25 psi / 1.6 bar 8.0 Watt

E. Options 1. Glass-filled PPS body material (suffix = “4”). (Not available for dual-tubing valves.) Changing the

body material from ASA/PC to PPS provides two advantages: a. Enhanced chemical resistance in the case of spills onto the body or when using aggressive cleaning

agents on the valves. b. Longer cycle life, extending the valve life cycles from 2 million to 5 million.

2. “Quiet” operation (suffix = “Q”). Implementing the “quiet” option reduces the valve noise level from about 72 dB to about 52 dB. The “quiet” option is available for: a. 100P2NC-way normally closed valves. b. 100P2NO-way normally open valves. The “quiet” option cannot be used on 100P3MP three-way valves. The noise level of the 3-way valves is inherently attenuated by tubing dampening the motion in both directions.

12 VDC valves with C-Flex® tubing. 2-Way: 12-inch (30cm) strip of silicone tubing is installed in the valve. 3-Way: Two 6-inch (15cm) strips of silicone tubing joined by ‘Y’ connector installed in the valve.

12 VDC valves without factory-installed tubing. Valves can be used with Bio-Chem Fluidics supplied silicone or C-Flex® tubing. 2-Way: 12-inch (30cm) strip of silicone tubing is installed in the valve. 3-Way: Two 6-inch (15cm) strips of silicone tubing joined by ‘Y’ connector installed in the valve.

24

3. Mounting holes (suffix = “M”) situated on the bottom of the valve body (i.e. the plastic). The dimensions are as follows: 1. A (thread) = #4-40 2. B = 0.687 inches / 17.5mm center-to-center 3. C = 0.218 inches / 5.54mm The mounting holes cannot be used in combination with the manual override button.

4. Position feedback sensor (suffix = “F”). The feedback sensor can be mounted on 075P pinch valves in the normally closed and the three-way configurations. (Please see page XX for details about this option.)

5. Manual override button (suffix = “K”). The manual override button is available for all 2-way and 3-way valve configurations except for dual-tubing valves. Its uses include: a. Flow control for emergencies during electric power loss. b. To facilitate tubing changes.

6. Factory-installed mounting flange (suffix = “L”). The mounting flanges are available for all 100P pinch valve configurations. They will be installed at a 90º angle to the tubing with the orientation to the outside of the bulkhead. a. 30% glass-filled polypropylene material provides secure

fit. b. Can be cleaned with alcohol, bleaches and other

cleaning agents. c. White color. d. Distance between mounting hole centers = 1.56” /

3.97cm. The footprint is identical as that of Sirai pinch valves.

e. The flanges can be installed at angles other than 90º to the tubing and/or with orientation to the inside of the bulkhead upon request.

This mounting flange can be purchased as a stand-alone item under part number MFP-100. Please see page XX for details.

F. “Hit and Hold” voltage reduction Within 100 ms of valve actuation, the voltage required to hold the valve in position can be reduced. The voltage step-down results in the dual benefits of power conservation and heat reduction. The amount of the voltage reduction possible is:

66% (i.e. 24 Vdc to 8 Vdc or 12 Vdc to 4 Vdc) for all 100P pinch valves that do not incorporate the “quiet” feature. This results in a power usage / heat generation drop of 89%.

50% (i.e. 24 Vdc to 12 Vdc or 12 Vdc to 6 Vdc) for all 100P pinch valves with the “quiet” feature. This results in a power usage / heat generation drop of 75%.

The voltage reduction can be accomplished using the Bio-Chem Fluidics CoolCube hit-and-hold circuit. Please see page XX for details.

25

G. Dimensions

100P2NC Normally Closed 2-Way Pinch Valve

100P2NO Normally Open 2-Way Pinch Valve

100P3MP 3-Way Pinch Valve

26

OPTICAL POSITION FEEDBACK SENSOR

Position feedback is provided through a compact, factory-mounted infrared optical sensor that instantaneously detects the position of the pinch valve pusher/armature assembly. An electrical signal is transmitted back to the instrument control system, confirming whether the valve is open or closed. With no moving parts, the optical sensor has a virtually unlimited life. The position feedback sensor is an essential feature in many critical operations, such as in life-sustaining medical applications.

A. Design and dimensions.

B. Feedback sensor installation in the instrument

1. Electrical specifications: Input voltage: 5.0 VDC Maximum output voltage: 30.0 VDC Maximum output current: 40.0 mA

Proper valve function is indicated by a drop in feedback voltage when the valve is open.

2. Installation: a. Connect sensor leads, Red (+) and Black (-), to a 5 VDC power supply. b. Connect the valve leads, Brown (+) and Blue (-), to a 12 VDC or 24 VDC power supply

as indicated on the valve label. c. Connect the signal lead, White (+), to a positive rail via the appropriate resistor. The

feedback voltage and pull-up resistor will depend on the electrical load in the system.

3. Typical setup diagram:

27

CoolCube™ “Hit and Hold” Circuit

Features of the CoolCube™.

Steps down DC voltage through pulse width modulation after 100 ms.

Reduces power consumption and heat generation while in “hold” setting.

Permits faster response and longer stroke through brief use of voltage above valve nominal rating.

No power storage. Valve turns off immediately when power is cut to the circuit.

Terminal pins for easy in-line installation.

A. Specifications

CoolCube-R 01356-52

CoolCube-50

Time from “hit” to “hold” voltage: 100 ms 100 ms Voltage step-down percentage: 67% 50% Maximum input voltage: 36 VDC 36 VDC Maximum input current: 1 amp 1 amp “Hold” voltage with 36 VDC input: 12 VDC 18 VDC “Hold” voltage with 24 VDC input: 8 VDC 12 VDC “Hold” voltage with 12 VDC input: 4 VDC 6 VDC Power consumption reduction: 89% 75%

B. Installation 1. Connect to DC power supply using AMP™, Molex® or similar connector. Respect polarity. 2. Connect to valve lead wires using AMP™, Molex® or similar connector. No polarity requirement. 3. Turn on the power supply.

C. Dimensions

28

FlowTest™

Automated controller for micro-fluidic systems

FlowTest™ is an automated controller that operates up to eight fluidic control devices (FCD’s, such as solenoid valves and pumps), each of which can be run in parallel or independently. Programming is carried out using the dedicated CosDesigner™ software running on a PC or a laptop computer. Multiple programs can be set up, stored and managed. The fields of use include laboratory and industrial applications requiring precise liquid transfers, sampling and injection.

FlowTest™ can also operate as a stand-alone instrument, without a computer. In this mode, programs are loaded using a USB key. The controller is operated by “run” and “stop” buttons conveniently located on top of the control unit.

A. Technical specifications Dimensions: 22 x 18 x 8.5 cm / 9 x 7 x 3.5 inches Capacity: Up to 8 valves and pumps running in parallel. Output voltage: 12 V or 24 V External trigger: 4 IRQ’s (0-5V TTL, dry contact) permitting the start or stop of valve or pump

operation. IRQ inputs through female CINCH/AV connectors. FCD connection: Spring-loaded terminal blocks with bi-color LED’s indicating state of actuation. USB-A port: Designated for USB key for loading programs into controller. A USB key

loaded with the Bio-Chem Fluidics database is supplied with the controller. USB-B port: Designated for PC or laptop connection. Input voltage: 110-120 V, 60 Hz / 220-240 V, 50 Hz. Power cables with U.S. and European

plugs are supplied with the controller. Programming: CosDesigner™ tool can be run on Windows Vista and Windows XP operating

systems in either 32-bit or 64-bit versions.

B. Characteristics of the main screen of the CosDesigner™ software

Graphic window for micro-fluidic diagrams.

Library of fluid system components, incl. valves and pumps.

Preview window used to pan and zoom around the graphic window.

Table of FCD’s and their technical characteristics.

Visualization of program sequence.

Visualization of the Pulse Width Modulation (PWM) signals for each FCD.

29

BARBED FITTINGS

Adaptors for soft-walled tubing to ¼”-28 threaded ports.

A. DIBA Click-N-Seal™ Barbed Adaptors

Click-N-Seal barbed fittings allow you to feel and hear that the fitting is properly installed. When the correct torque is reached, the cap emits an audible click. The fitting itself does not tighten beyond the torque limit. Both the port and the fitting are protected from over-tightening and cannot be stripped.

The wetted material is polycarbonate.

Part No. Tubing inner diameter

Thread Cap color

008NB16-CS5R 1/16” / 1,6mm Male ¼”-28 Red 008NB32-CS5R 1/8” / 3.2mm Male ¼”-28 Red 008NB40-CS5R 5/32” / 4.0mm Male ¼”-28 Red

B. OMNIFIT® ¼”-28 Thread to Barbed Adaptors

Omnifit® barbed adaptors are designed for use with soft wall tubing. Machined from chemically resistant PEEK™ (polyetheretherketone) or Acetal material, they have a superior barb with a crisp edge that retains tubing more securely than molded adaptors.

The PEEK fittings have a natural brown color and the Acetal fittings are white.

30

PEEK fitting Part No.

Acetal fitting Part No.

Tubing inner diameter

008NB10-KD2L 06463-61

008NB10-AD2B 0.039” / 1.0mm

008NB15-KD2L 06463-62

008NB15-AD2B 1/16” / 1.5mm

008NB20-KD2L 06463-63

008NB20-AD2B 0.79” / 2.0mm

008NB25-KD2L 06463-64

008NB25-AD2B 1.0” / 2.5mm

008NB32-KD2L 06463-65

008NB32-AD2B 1/8” / 3.2mm

PEEK fitting Part No.

Acetal fitting Part No.

Tubing inner diameter

008NB10-KD5L 06463-51

008NB10-AD5B 0.039” / 1.0mm

008NB15-KD5L 06463-52

008NB15-AD5B 1/16” / 1.5mm

008NB20-KD5L 06463-53

008NB20-AD5B 0.79” / 2.0mm

008NB25-KD5L 06463-54

008NB25-AD5B 1.0” / 2.5mm

008NB32-KD5L 06463-55

008NB32-AD5B 1/8” / 3.2mm

008NB40-KD5L 06463-56

008NB40-AD5B 5/32” / 4.0mm

008NB60-KD5L 06463-57

008NB60-AD5B 1/4” / 6.0mm

008NB80-KD5L 06463-58

008NB80-AD5B 5/16” / 8.0mm

Female ¼”28 thread to barbed adaptors in PEEK and Acetal

Male ¼”28 thread to barbed adaptors in PEEK and Acetal

31

C. Polypropylene tubing connectors

32

MOUNTING OPTIONS A. MFP-075 and MFP-100 Mounting Flanges

1. Features 30% glass-filled polypropylene material. Spring steel retainer and set screw ensure

secure fit. Can be cleaned with alcohol, bleaches and

other cleaning agents. White color. Can be mounted on inside or outside of

bulkhead. Angle relative to tubing entirely adjustable. 2. Installation Option 1: factory installed in the position requested by the customer (part number suffix “L”).

Security of the flange position is enhanced through a dowel pin inserted into the metal valve shell. Option 2: installed by customer facing inside or outside of bulkhead at desired angle to tubing.

3. Dimensions

MFP075

MFP100

33

B. Spring Steel Mounting Clip, Polyethylene Mounting Flange, Aluminum Mounting Ring

Documents

Solenoid Operated Pinch Valves - Cole-Parmer 2-way 3-way Dual 3-way Choice of tubing materials. Bio-Chem Fluidics offers two high-purity medical grade tubing materials for pinch valves: