Upload
alexjdm
View
375
Download
7
Embed Size (px)
Citation preview
8/13/2019 Solidworks Tutorial For Beginner
1/104
8/13/2019 Solidworks Tutorial For Beginner
2/104
i
Foreword
The main objective of these tutorials is to give you a kick start using SolidWorks. The approach to
write this tutorial is based on what is the most important knowledge you should know and what is
commonly tool used. You will learn step by step by working on it. These tutorials will teach you
the basic skills of using Solidworks in your daily design works. Even this tutorials didnt have fullexplanations of tools that Solidworks have but dont worry you will master it along the way, as I
did.
If you have any questions about these tutorials, drop your mail to
Solidworks 2010 Tutorials: Beginner
http://www.solidworkstutorials.com
2010 solidworkstutorials.com , All rights reserved.
This publication is copyright under the solidworkstutorials.com
All rights reserved. Apart from any fair dealing for the purpose of private study, research, criticism, or review, as permitted
under the Copyright Designs and Patents Act 1988, no part may be reproduced, stored
in a retrieval system, or transmitted in any form or by any means, electronic, electrical, chemical, mechanical,photocopying, recording or otherwise, without the prior permission of the copyright owners. Unlicensed multiple copying
of this publication is illegal. Inquiries should be addressed to: [email protected]
If this guide is distributed with software that includes an end-user agreement, this guide, as well as the software described
in it, is furnished under license and may be used or copied only in accordance with the terms of such license. Except as
permitted by any such license, no part of this guide may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of
solidworkstutorials.com. Please note that the content in this guide is protected under copyright law even if it is not
distributed with software that includes an end-user license agreement. The content of this guide is furnished for
informational use only, is subject to change without notice, and should not be construed as a commitment by
solidworkstutorials.com. Solidworkstutorials.com assumes no responsibility or liability for any errors or inaccuracies that
may appear in the informational content contained in this guide. Please remember that existing artwork or images that
you may want to include in your project may be protected under copyright law. The unauthorized incorporation of such
material into your new work could be a violation of the rights of the copyright owner. Please be sure to obtain anypermission required from the copyright owner. Any references to company names in sample templates are for
demonstration purposes only and are not intended to refer to any actual organization.
The publishers are not responsible for any statement made in this publication. Data, discussion, and conclusions
developed by the Author are for information only and are not intended for use without independent substantiating
investigation on the part of the potential users. Opinions expressed are those of the Author and are not necessarily those
of the Institution of Mechanical Engineers or its publishers.
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/8/13/2019 Solidworks Tutorial For Beginner
3/104
Solidworks Tutorials: Beginner Table of contents www.solidworkstutorials.com
Solidworks Tutorials: Beginner Table of contents ii
Table of contents
Beginner Part 1: My First Solid 1
The big picture how SolidWorks works, it starts
with a simple editable sketch. From this sketch a
feature build the solid. From this solid itproduces drawing...
Beginner Part 2: Sketching 10
Sketch is the base of your part, its a good
practice to master sketching in SolidWorks...
Beginner Part 3: Turning Parts 23
Some parts such as pins and shafts can be
manufacture by turning process on lathe
machine, we can create turning part by revolving
it sketch on it axis...
Beginner Part 4: Hole Wizard 30
Hole Wizard is used for creating predefined and
standard holes such as counter bore hole,
counter sunk hole, screw clearance hole and
many more...
Beginner Part 5: Pattern 40
Pattern (or some called array) is used to repeat
features in linear arrangement or circular
arrangement. Its good to know how to optimize
these tool, it help you make your part faster and
easier...
Beginner Part 6: Assembly Parts 60
Assembly is a part of design process, it show how
all designed parts work together as a single
unit...
Beginner Part 7: Detailing Drawing 80
Once solid parts created we need to transfer it to
engineering drawing so the others can
understand your parts
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/8/13/2019 Solidworks Tutorial For Beginner
4/104
Beginner Part 1: My First Solid www.solidworkstutorials.com
Beginner Part 1: My First Solid 1
Beginner Part 1: My First Solid
The big picture how SolidWorks works, it starts with a simple
editable sketch. From this sketch a feature build the solid. From
this solid it produces drawing... Lets begin your first solid...
1. Click New , click Part , OK.
2. Click Front Plane, insert sketch on plane by click Sketch.
3. Click Sketch , click
Corner Rectangular . Start first point at origin and
click another point at top right side.
4. Click Smart Dimension , click top edge set
dimension to 3inand click right edge set dimension to 2in.
In this tutorial you will make this
bracket, start from sketch and build
features.
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/8/13/2019 Solidworks Tutorial For Beginner
5/104
Beginner Part 1: My First Solid www.solidworkstutorials.com
Beginner Part 1: My First Solid 2
5. To build features, click Extruded Boss/Base , set D1to
0.10in and .
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/8/13/2019 Solidworks Tutorial For Beginner
6/104
Beginner Part 1: My First Solid www.solidworkstutorials.com
Beginner Part 1: My First Solid 3
6. Click on front face of the part, click Normal To.
7. Click Circle , sketch circle on face
.
Click Smart Dimension , click circle edge and set
diameter to 0.6in. For circle positioning click circle edge and
vertical part edge set to 0.5in. Click circle edge again and
click horizontal part edge set to 0.5in.
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/8/13/2019 Solidworks Tutorial For Beginner
7/104
Beginner Part 1: My First Solid www.solidworkstutorials.com
Beginner Part 1: My First Solid 4
8. Click Extruded Cut , change Direction 1to Through
All and .
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/8/13/2019 Solidworks Tutorial For Beginner
8/104
Beginner Part 1: My First Solid www.solidworkstutorials.com
Beginner Part 1: My First Solid 5
9. Click on front face and select Sketch
.
Select Corner Rectangular sketch rectangular from
top right edge to center.
10. Click Smart Dimension , set rectangular
dimension to 2inand 1in.
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/8/13/2019 Solidworks Tutorial For Beginner
9/104
Beginner Part 1: My First Solid www.solidworkstutorials.com
Beginner Part 1: My First Solid 6
Click
Extruded Cut and select Through All
and .
11. Click on front face and select Sketch
. Click
Corner Rectangular and sketch rectangular start
form bottom left edge to right edge.
8/13/2019 Solidworks Tutorial For Beginner
10/104
Beginner Part 1: My First Solid www.solidworkstutorials.com
Beginner Part 1: My First Solid 7
Click
Smart Dimensionand set rectangular height to 0.1in.
12. Click Extruded Boss/Base set Direction 1 to 0.5in
and . Click Display
Styleand select Isometric.
8/13/2019 Solidworks Tutorial For Beginner
11/104
Beginner Part 1: My First Solid www.solidworkstutorials.com
Beginner Part 1: My First Solid 8
13. Click Fillet , check Full preview
add fillet to all edges
8/13/2019 Solidworks Tutorial For Beginner
12/104
Beginner Part 1: My First Solid www.solidworkstutorials.com
Beginner Part 1: My First Solid 9
and
.
14. Save the part as Bracket and youre done! Simple isntit?
Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/8/13/2019 Solidworks Tutorial For Beginner
13/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 10
Beginner Part 2: Sketching
Sketch is the base of your part, its a good practice to master
sketching in SolidWorks...
1. Click New , click Part , OK.
2. Click Front Plane, insert sketch on plane by click Sketch.
3. Click Sketch , click
Corner Rectangular . Start first point at origin and
click another point at top right side.
4. Click Smart Dimension , click top edge set
dimension to 2inand click right edge set dimension to 2in.
In this tutorial you will make this
box, start from sketch and build
features. Youll learn how to use
sketch tools to build this part.
8/13/2019 Solidworks Tutorial For Beginner
14/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 11
5. To build features, click Features>Extruded Boss/Base
, set D1to 0.50in
and .
8/13/2019 Solidworks Tutorial For Beginner
15/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 12
6. Click on front face of the part, click Normal To.
7. Click on front face and click Sketch.
8/13/2019 Solidworks Tutorial For Beginner
16/104
8/13/2019 Solidworks Tutorial For Beginner
17/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 14
10. Click on side face, click Sketch.
11. While pressing Ctrlkey select inner left and right edge.
Click
Convert Entities .
12. Select Centerline from line menu ,
sketch a centerline midpoint to midpoint of both converted
8/13/2019 Solidworks Tutorial For Beginner
18/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 15
edges.
13. Click sketched centerline
and click Offset Entities.
8/13/2019 Solidworks Tutorial For Beginner
19/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 16
Set Parameter, D to 0.3incheck Bi-directionaland .
14. Now click Trim Entities to remove excess line,
before make any cut make sure under option Trim to
closestis selected. Trim extra line as
below sketch. Answers Yesif notification appear.
15. Click View Orientation>Isometric.
16. Click Features>Extruded Boss/Base , for Direction 1,
click Reverse Direction(green box) and set D1to 0.1in.
8/13/2019 Solidworks Tutorial For Beginner
20/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 17
and .
8/13/2019 Solidworks Tutorial For Beginner
21/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 18
17. Click on front face and click Normal To.
18. Click on front face and click Sketch.
8/13/2019 Solidworks Tutorial For Beginner
22/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 19
19. Click Circle, sketch circle at left edge.
20. Click Smart Dimension, dimension sketch as
below sketch.
21. Click on sketched circle, click
Copy Entities. Set delta x
8/13/2019 Solidworks Tutorial For Beginner
23/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 20
to 0.3in and .
22. Click Centerline, sketch centerlineacross front face and make sure it starts at midpoint left edge
and midpoint right edge and .
23. While press Ctrlkey, select both sketched circle and click
Mirror Entities , on Mirror Optionclick
Mirror about:box, and select centerline
8/13/2019 Solidworks Tutorial For Beginner
24/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 21
and .
24. Click Extruded Cut, and set D1to 0.1in
and .
25. Click View Orientation>Back,
8/13/2019 Solidworks Tutorial For Beginner
25/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 22
and click on back face and click Sketch.
26. Click Sketch>Circle, sketch circle at lower left edge.
Click Smart
Dimension and dimension sketched circle as
sketch below.
and .
8/13/2019 Solidworks Tutorial For Beginner
26/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 23
27. Click on sketched circle, and click
Linear Sketch Pattern and on
Direction 1set D1to 1.2inand on Direction 2, change #to
2and set D2to 1.2inand .
8/13/2019 Solidworks Tutorial For Beginner
27/104
Beginner Part 2: Sketching www.solidworkstutorials.com
Beginner Part 2: Sketching 24
28. Click Features>Extruded Cut, and set direction to
Through All and .Click View Orientation>Isometric.
29. Save the part as Sketch and youre done! Simple isnt
it?
Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/8/13/2019 Solidworks Tutorial For Beginner
28/104
Beginner Part 3: Turning Part www.solidworkstutorials.com
Beginner Part 3: Turning Part 25
Beginner Part 3: Turning Part
Some parts such as pins and shafts can be manufacture by
turning process on lathe machine, we can create turning part by
revolving it sketch on it axis...
1. Click New, click Part, OK.
2. Click Front Plane, insert sketch on plane by click Sketch.
3. Click on Line, sketch a closed loop start at origin, sketch
as sketch below end back at origin.
and
4. Click Smart Dimension and dimension sketch as
sketch below.
and .
5. Click Features>Revolved Boss/Base,and click on bottom line as it axis.
In this tutorial you will make this
pin, start from sketch and build
solid body by revolve it sketch on
axis. Youll learn how to use
revolved boss/base and revolved
cut to build this part.
8/13/2019 Solidworks Tutorial For Beginner
29/104
Beginner Part 3: Turning Part www.solidworkstutorials.com
Beginner Part 3: Turning Part 26
and .
6. Click View Orientation>Front
and click Front Planeand click Sketch.
8/13/2019 Solidworks Tutorial For Beginner
30/104
Beginner Part 3: Turning Part www.solidworkstutorials.com
Beginner Part 3: Turning Part 27
7. Click Corner Rectangle, and sketch rectangle overlap
on solid body as sketched below.
and .
8. Click Smart Dimension and dimension sketch as
sketched below.
9. To view solid body axis, click View>Temporary Axes.
10. To make second undercut, click Features>Revolved Cut
and select temporary axes as it axis
8/13/2019 Solidworks Tutorial For Beginner
31/104
Beginner Part 3: Turning Part www.solidworkstutorials.com
Beginner Part 3: Turning Part 28
and .
8/13/2019 Solidworks Tutorial For Beginner
32/104
Beginner Part 3: Turning Part www.solidworkstutorials.com
Beginner Part 3: Turning Part 29
11. To hide temporary axes, click View>Temporary Axes.
12. Save the part and youre done! Simple isnt it?
Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/8/13/2019 Solidworks Tutorial For Beginner
33/104
Beginner Part 4: Hole Wizard www.solidworkstutorials.com
Beginner Part 4: Hole Wizard 30
Beginner Part 4: Hole Wizard
Hole Wizard is used for creating predefined and standard holes
such as counter bore hole, counter sunk hole, screw clearance
hole and many more...
1. Click New, click Part, OK.
2. Click Top Plane, insert sketch on plane by click Sketch.
3. Click on Corner Rectangle, sketch a rectangle start at
origin.
and .
4. Click Smart Dimension and dimension sketch as
sketch below.
and .
5. Click Features>Extruded Boss/Base, on Direction 1
set D1to 1in
In this tutorial you will add
counterbore, countersink and tap
holes to this plate by using Hole
Wizard tools.
8/13/2019 Solidworks Tutorial For Beginner
34/104
Beginner Part 4: Hole Wizard www.solidworkstutorials.com
Beginner Part 4: Hole Wizard 31
and .
6. Click on top face and click Normal To.
7. Click Features>Hole Wizard on Hole Type, select
Counterbore, Standardto Ansi Inch, Typeto Socket Head
Cap Screw, Sizeto #10, Fitto Normaland End Condition
to Through All.
8/13/2019 Solidworks Tutorial For Beginner
35/104
Beginner Part 4: Hole Wizard www.solidworkstutorials.com
Beginner Part 4: Hole Wizard 32
For positions placement for this counterbore hole, click on
Positionstab. Now click three
more positions at each edge.
8/13/2019 Solidworks Tutorial For Beginner
36/104
Beginner Part 4: Hole Wizard www.solidworkstutorials.com
Beginner Part 4: Hole Wizard 33
8. Click on Smart Dimensions, click on center point
of counterbore hole and click left edge, set dimension to
0.5in.
Continue dimensioning as sketched below.
and .
9. For adding countersink at center, click on top faceand click
on Hole Wizard .
8/13/2019 Solidworks Tutorial For Beginner
37/104
Beginner Part 4: Hole Wizard www.solidworkstutorials.com
Beginner Part 4: Hole Wizard 34
On Hole Type, select Countersink, Standardto Ansi Inch,
Typeto Flat Head Screw (100), Sizeto #10, Fitto Normal
and End Conditionto Through All.
10. For positions placement for this countersink holes, click on
Positionstab. Now click three
more positions at center.
8/13/2019 Solidworks Tutorial For Beginner
38/104
Beginner Part 4: Hole Wizard www.solidworkstutorials.com
Beginner Part 4: Hole Wizard 35
11. Click on Smart Dimensions, click on center point
of countersink hole and click left edge, set dimension to
2.5in.
Continue dimensioning as sketched below.
and .
12. For adding center tap hole, click on top face at center and
click Hole Wizard.
8/13/2019 Solidworks Tutorial For Beginner
39/104
Beginner Part 4: Hole Wizard www.solidworkstutorials.com
Beginner Part 4: Hole Wizard 36
On Hole Type, select Tap, Standardto Ansi Inch, Typeto
Tapped hole, Sizeto 1/2-13, End Conditionto Through
All.
13. For positions placement for this tap hole, click on Positions
tab. There is another style to
positions hole wizard is define it position by sketch, let try it.
Click on Centerline, Sketch a
horizontal line start at midpoint of left edge to midpoint left
8/13/2019 Solidworks Tutorial For Beginner
40/104
Beginner Part 4: Hole Wizard www.solidworkstutorials.com
Beginner Part 4: Hole Wizard 37
edge. Press Escto end sketch centerline.
14. Click and drag tap center to midpoint of centerline.
and .
15. Click View Orientation>Isometric. Done.
8/13/2019 Solidworks Tutorial For Beginner
41/104
Beginner Part 4: Hole Wizard www.solidworkstutorials.com
Beginner Part 4: Hole Wizard 38
16. Save the part as Plate1 and youre done! Simple isnt it?
Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/8/13/2019 Solidworks Tutorial For Beginner
42/104
8/13/2019 Solidworks Tutorial For Beginner
43/104
Beginner Part 5: Pattern www.solidworkstutorials.com
Beginner Part 5: Pattern 40
and .
6. Click on top faceand click Normal To.
7. Click on top faceand click Sketch.
8/13/2019 Solidworks Tutorial For Beginner
44/104
Beginner Part 5: Pattern www.solidworkstutorials.com
Beginner Part 5: Pattern 41
Click on Circle and sketch a circle on top face and .
8. Click on Smart Dimension and dimension
sketched circle as sketch below.
9. Click Features>Extruded Cut on Direction 1set to
Through All. and .
10. Click Features>Hole Wizard on Hole Type, select
Counterbore, Standardto Ansi Inch, Typeto Socket Head
Cap Screw, Sizeto #10, Fitto Normaland End Condition
to Through All.
8/13/2019 Solidworks Tutorial For Beginner
45/104
Beginner Part 5: Pattern www.solidworkstutorials.com
Beginner Part 5: Pattern 42
For positions placement for this counterbore hole, click on
Positionstab. Click one point
at lower left edge.
8/13/2019 Solidworks Tutorial For Beginner
46/104
Beginner Part 5: Pattern www.solidworkstutorials.com
Beginner Part 5: Pattern 43
11. Click on Smart Dimension and dimension
sketched circle as sketch below.
and .
12. To pattern this counterbore hole, click on CBORE for #10
Socket Head Cap Screw1
and click Linear Pattern. Click on bottom edge as
Direction 1pattern.
8/13/2019 Solidworks Tutorial For Beginner
47/104
Beginner Part 5: Pattern www.solidworkstutorials.com
Beginner Part 5: Pattern 44
Set D1to 2.5inand pattern # to 3. Click on highlighted
arrowto switch it directions.
13. Click on left edgeas Direction 2pattern.
Set D2to 3.4inand number of pattern #to 2. You can click
8/13/2019 Solidworks Tutorial For Beginner
48/104
8/13/2019 Solidworks Tutorial For Beginner
49/104
Beginner Part 5: Pattern www.solidworkstutorials.com
Beginner Part 5: Pattern 46
Click Smart Dimension, set circle diameter to
1.5in.
15. Click Line, sketch a vertical line crossing sketch circle at
12 oclock to 6 oclock.
Press Esckey to end Line. Exit sketch.
16. Click on Hole Wizard, on Hole Typeclick on Tap,Standard: Ansi Inch, Type: Tapped Hole, Hole
Specifications Size:1/4-20, End Condition Through All.
8/13/2019 Solidworks Tutorial For Beginner
50/104
Beginner Part 5: Pattern www.solidworkstutorials.com
Beginner Part 5: Pattern 47
For positions placement for this tap hole, click on Positions
tab. Click one point at 12
oclock last sketched circle.
8/13/2019 Solidworks Tutorial For Beginner
51/104
Beginner Part 5: Pattern www.solidworkstutorials.com
Beginner Part 5: Pattern 48
and .
17. To hide guide sketch, click Sketch4and click Hide.
18. To pattern tap hole, click on 1/4-20 Tapped Hole1
and click Circular Pattern.
Change view to isometric by click on View
Orientation>Isometric
Click on open inner hole faceas its pattern axis, set
instances #to 6and .
8/13/2019 Solidworks Tutorial For Beginner
52/104
Beginner Part 5: Pattern www.solidworkstutorials.com
Beginner Part 5: Pattern 49
19. Save the part as Blockand youre done! Simple isnt it?
Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/8/13/2019 Solidworks Tutorial For Beginner
53/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 50
Beginner Part 6: Assembly Parts
Assembly is a part of design process, it show how all designed
parts work together as a single unit. ...
1. Click New, click Part, OK.
2. Click Front Plane, insert sketch on plane by click Sketch.
3. Click on Corner Rectangle, sketch a rectangle start at
origin.
and .
4. Click Smart Dimension and dimension sketch as
sketch below.
and .
5. Click Features>Extruded Boss/Base, on Direction 1
set D1to 4in
In this tutorial you will create this
toy horse by assembly parts to one
unit assembly.
8/13/2019 Solidworks Tutorial For Beginner
54/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 51
and .
6. Click on right faceand click Normal To.
8/13/2019 Solidworks Tutorial For Beginner
55/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 52
7. Click on right faceagain and click Sketch.
Click on Circle and sketch 4 circle at each corner. Click
on Smart Dimension and dimension sketch as
sketched below.
8. Click on Features>Extruded Cut and set Direction 1 to
Through All and . Click
on View OrientationIsometric.
8/13/2019 Solidworks Tutorial For Beginner
56/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 53
9. Click on top face and click Normal To.
Click on top face again and click Sketch.
8/13/2019 Solidworks Tutorial For Beginner
57/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 54
Click on Corner Rectangle and sketch 2 rectangles at
top and bottom.
Click on Smart Dimension and dimension theserectangles as sketched below.
8/13/2019 Solidworks Tutorial For Beginner
58/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 55
10. Click on Features>Extruded Cut and set Direction 1 to
1.0in
and .
Click on View Orientation>Isometric.
8/13/2019 Solidworks Tutorial For Beginner
59/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 56
11. Save the part as Body.
12. Click New, click Part, OK.
13. Click Right Plane, insert sketch on plane by click Sketch.
14. Click on Corner Rectangle, sketch a rectangle start at
origin.
and .
8/13/2019 Solidworks Tutorial For Beginner
60/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 57
15. Click Smart Dimension and dimension sketch as
sketch below.
16. Click Centerline and sketch vertical
centerline through top edge midpoint to bottom midpoint.
Press Escto end centerline.
8/13/2019 Solidworks Tutorial For Beginner
61/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 58
17. Click on Circle, sketch 3 circles onto centerline and
using Smart Dimension dimension sketch as
sketched below.
18. Click Features>Extruded Boss/Base, on Direction 1
set D1to 0.25in
and . Click on View
Orientation>Isometric.
8/13/2019 Solidworks Tutorial For Beginner
62/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 59
19. To change part color, right click on
Part2>Appearance>Appearance
On Colorselect Shinyand pick whitecolor.
and .
20. Save the part as Leg.
21. Click New, click Part, OK.
8/13/2019 Solidworks Tutorial For Beginner
63/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 60
22. Click Right Plane, insert sketch on plane by click Sketch.
23. Click on Circle, and sketch a circle. Click Smart
Dimension dimension this circle to 0.25in.
24. Click Features>Extruded Boss/Base, on Direction 1
set D1to 0.25in
and .
25. Click on right faceand click Normal To.
Click on this face againand click Sketch.
8/13/2019 Solidworks Tutorial For Beginner
64/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 61
26. Click on Circle, and sketch a circle. Click Smart
Dimension dimension this circle to 1.5in.
27. Click Features>Extruded Boss/Base, on Direction 1
set D1to 0.25in
and .
28. To change part color, right click on
Part3>Appearance>Appearance
8/13/2019 Solidworks Tutorial For Beginner
65/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 62
On Colorselect Standardand pick redcolor.
and .
29. Save the part as Wheel.
30. Click New, click Part, OK.
31. Click Right Plane, insert sketch on plane by click Sketch.
8/13/2019 Solidworks Tutorial For Beginner
66/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 63
32. Click on Line, and sketch a horse head.
33. Click on Smart Dimension and dimension sketch
as sketched below.
34. Click Features>Extruded Boss/Base, on Direction 1
set D1to 0.5in
and .
35. To change part color, right click on
Part4>Appearance>Appearance
8/13/2019 Solidworks Tutorial For Beginner
67/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 64
On Colorselect Shinyand pick whitecolor.
and .
36. Save the part as Head.
37. Click New, click Part, OK.
8/13/2019 Solidworks Tutorial For Beginner
68/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 65
38. Click Right Plane, insert sketch on plane by click Sketch.
39. Click on Line, and sketch a horse tail.
40. Click on Smart Dimension and dimension sketch
as sketched below.
8/13/2019 Solidworks Tutorial For Beginner
69/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 66
41. Click Features>Extruded Boss/Base, on Direction 1
set D1to 0.5in
and .
42. To change part color, right click on
Part5>Appearance>Appearance
On Colorselect Shinyand pick whitecolor.
8/13/2019 Solidworks Tutorial For Beginner
70/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 67
and .
43. Save the part as Tail.
Lets begin assembly all this parts.
44. Click New, click Assembly, OK.
45. To add part in assembly, Click Browse
8/13/2019 Solidworks Tutorial For Beginner
71/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 68
SelectBody.sldprt and clickOpen. Click on workspace.
46. To add leg part, click Insert Components , click
Browse
8/13/2019 Solidworks Tutorial For Beginner
72/104
8/13/2019 Solidworks Tutorial For Beginner
73/104
8/13/2019 Solidworks Tutorial For Beginner
74/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 71
Coincident mate already pre selected, click .
49. Turn the assembly back to previous view.
8/13/2019 Solidworks Tutorial For Beginner
75/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 72
50. Click on inner hole face on bodyand inner hole of leg.
The Concentric mate already pre selected, click . Repeat
this step for bottom hole.
and .
51. Turn the assembly the other way.
8/13/2019 Solidworks Tutorial For Beginner
76/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 73
52. Click on wheel shaft face and inner leg hole.
Concentric mate already pre selected, click .
53. Click on inner wheel face
turn the assembly to left side and click on outer leg face.
Coincident mate already pre selected, click .
54. Repeat step 46 53 for other set of legs and wheels.
55. To add head part, click Insert Components ,
click Browse
8/13/2019 Solidworks Tutorial For Beginner
77/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 74
SelectHead.sldprt and clickOpen. Click on workspace. To
add tail part, click Insert Components , click
Browse
Select Tail.sldprt and clickOpen. Click on workspace.
8/13/2019 Solidworks Tutorial For Beginner
78/104
8/13/2019 Solidworks Tutorial For Beginner
79/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 76
Coincident mate already pre selected, click .
58. Click on top edge of tail,
turn assembly to view top body and click on top face of the
body.
Coincident mate already pre selected, click .
59. Turn the model to facing front of the body, click on side face
of inner cut,
8/13/2019 Solidworks Tutorial For Beginner
80/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 77
turn the assembly to left and click on head side face.
Coincident mate already pre selected, click .
60. Click on inner cut face of the body,
turn the assembly around and click on back head face.
8/13/2019 Solidworks Tutorial For Beginner
81/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 78
Coincident mate already pre selected, click .
61. Turn the assembly to view front side, click on head lower
edge,
and click on body bottom inner cut.
Coincident mate already pre selected, click .
8/13/2019 Solidworks Tutorial For Beginner
82/104
Beginner Part 6: Assembly Parts www.solidworkstutorials.com
Beginner Part 6: Assembly Parts 79
62. Click View Orientation>Isometric
and youre done!
63. Save the assembly as Horseand youre done! Simple
isnt it?
Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/8/13/2019 Solidworks Tutorial For Beginner
83/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 70
Beginner Part 7: Detailing Drawing
Once solid parts created we need to transfer it to engineering
drawing so the others can understand your parts
1. Click New, click Drawing, OK.
2. On Sheet Format/Sizeselect A Landscapeand OK.
3. Click Browse...
locate you Block.sldprt(Part from Beginner Part 5: Pattern
tutorials)
In this tutorial you create drawing
for this part.
8/13/2019 Solidworks Tutorial For Beginner
84/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 71
Click Open.
4. For Orientation select Topand for Display Styleselect
Hidden Lines Visible,
8/13/2019 Solidworks Tutorial For Beginner
85/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 72
5. Click on sheet to add this view,
click again on left side to add side view of the part,
click once more to upper right of sheet to view its 3D view.
8/13/2019 Solidworks Tutorial For Beginner
86/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 73
Click .
6. Repositions part 3D view to upper right corner of the sheetby draggingit to this location.
7. There is no centerline for holes in side view, lets add this
centerline, click on side view,
8/13/2019 Solidworks Tutorial For Beginner
87/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 74
Click on Annotationtab,
click on Centerline,
centerline automatically added to side view, click .
8. Click Smart Dimension and click on bottom edgeand pull dimension to bottom.
8/13/2019 Solidworks Tutorial For Beginner
88/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 75
9. Zoom in, click on center hole edge,
click on counter bore hole edge
and pull dimension to bottom side.
8/13/2019 Solidworks Tutorial For Beginner
89/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 76
10. Click on center hole edge,
click on counter bore hole edge
8/13/2019 Solidworks Tutorial For Beginner
90/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 77
and pull dimension to bottom side.
11. Repeat step 10and continue dimension for the third counter
bore hole.
8/13/2019 Solidworks Tutorial For Beginner
91/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 78
8/13/2019 Solidworks Tutorial For Beginner
92/104
8/13/2019 Solidworks Tutorial For Beginner
93/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 80
13. Repeat step 12for right edge.
8/13/2019 Solidworks Tutorial For Beginner
94/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 81
14. Click on center hole edge and pull out its diameter
dimension.
8/13/2019 Solidworks Tutorial For Beginner
95/104
8/13/2019 Solidworks Tutorial For Beginner
96/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 83
16. Click on center hole edge,
click on counterbore hole edge
and pull its dimension to left side.
8/13/2019 Solidworks Tutorial For Beginner
97/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 84
17. Click on center hole edge,
click on bottom edge
and pull its dimension to left side.
8/13/2019 Solidworks Tutorial For Beginner
98/104
8/13/2019 Solidworks Tutorial For Beginner
99/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 86
20. Click on thread
and pull out its hole callout to right side.
Click to end hole callout annotation.
8/13/2019 Solidworks Tutorial For Beginner
100/104
8/13/2019 Solidworks Tutorial For Beginner
101/104
8/13/2019 Solidworks Tutorial For Beginner
102/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 89
23. You can customize each view how its appear on drawing bychanging its display style. Click on Section A-Aview,
on Display Styleclick on Hidden Line Removed.
Click . Your section view now changed.
8/13/2019 Solidworks Tutorial For Beginner
103/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
Beginner Part 7: Detailing Drawing 90
24. Click on 3D view,
on Display Styleclick on Shaded With Edges.
To change its scale, under Scaleclick on Use custom scale,
set to 1:3
and .
8/13/2019 Solidworks Tutorial For Beginner
104/104
Beginner Part 7: Detailing Drawing www.solidworkstutorials.com
25. Save the drawing as Blockand youre done! Simple isntit?
Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com
http://www.solidworkstutorials.com/http://www.solidworkstutorials.com/