Sound & Vision Bible...Crown XLS 602 #1 IN 1 2 OUT 1 2 FLOOR AUDIO JBL Control 30 REAR R JBL Control 30 FOH L JBL Control 30 FOH R Mackie SMR Sub L Mackie SRM450 ATMOS L Mackie SRM450

A MIDSUMMER NIGHTS DREAM

Complied by: Ben Mills

Sound & Vision Bible

Table of Contents

Page 3 Page 4Page 5Page 8Page 10Page 11Page 12Page 13Page 14Page 15Page 16Page 17Page 18 Page 21

Sound and Vision SchematicArchive Schematic

Sound and Vision Equipment ListSound and Vision Equipment Loan Request Form

Sound Patch SheetVision Patch SheetNetwork Allocation

Communications AllocationSpeaker Placement Plan

Speaker SectionVision Placement Plan

Vision SectionArchive Procedure

Sound & Vision Designer/QLab Operator Show Plot

SYSTEM

Page 27 Page 34Page 35Page 36

Sound Cue SynopsisAPRA Application

APRA DurationVision Cue Synopsis

DESIGN

Show

VenueVersion

Title

Drawn ByContact

A Midsummer Night’s Dream

The Loft, Kelvin GroveV3 as of 14/10/2018Sound & Vision Schematic

Benjamin Mills

Director

DesignersFrancesca Savige

Stephanie YauSet, Costume &Vision Designer

Nicholas SeeryLighting Designer

Benjamin MillsSound & Vision Designer/ QLab Operator

KEY NOTES

RIGGED

CISCO Network Switch 10 port

1 2 3 4 5 6 7 8

Mac Pro - Vision(Qlab 4, Decklink)

Ethernet Decklink Quad OUT8

IP Address: 192.168.10.161

Mac Mini - Sound(Qlab 4)

Ethernet Thunderbolt OUT

IP Address: 192.168.10.162

CAT 6DIN21 - SDISDIThunderbolt

MOTU 16A

IN

OUT IN[FOH L] 1[FOH R] 2

[REAR L] 3[REAR R] 4

[SUB L] 5[SUB R] 6

[ATMOS L] 7[ATMOS R] 8

910111213141516

12345678910111213141516

Soundcraft SI Expression 1

OUT123456789

10111213141516

TRS - XLR

JBL Control 30REAR L

XLR

Crown XLS 602 #1

IN12

OUT12

FLOOR AUDIO

JBL Control 30REAR R

JBL Control 30FOH L

JBL Control 30 FOH R

Mackie SMR Sub L

Mackie SRM450ATMOS L

Mackie SRM450ATMOS R

Crown XLS 602 #2

IN12

OUT12

Venue PatchingIN OUTSP12 - MIC 2SP14 - MIC 2SP12 - MIC 1SP14 - MIC 1

SP12 - AUD 2SP14 - AUD 2SP12 - AUD 1SP14 - AUD 1

Wireless Mic (Primary)Shure ULXD4D

ReceiverIN OUTRX1 1

Shure Wireless ULX SM58

RF OUT

RF

SDI IN

Panasonic PT-DZ21Kw/ ET-D75LE10

Ethernet

IP Address: 192.168.10.160

Monitor Speaker(for SM)

IN

SM Stage Feed

NTG3

- Computer Monitors have not been drawn.- Not to scale.- Comms System hasn’t been drawn in.- Speaker Placement refer to Speaker Placement plan.- Keyboard & Mouse not drawn.- Power not drawn.

Wireless Mic (Redundant)Shure ULXD4D

ReceiverIN OUTRX2 2

Shure Wireless ULX SM58

RF OUT

SM58

God Mic

Wireless Router (Production Desk)

Sound DesignerScreen Sharing

Ethernet

IP Address: 192.168.10.167

Vision DesignerScreen Sharing

Ethernet

IP Address: 192.168.10.169

Mackie SMR Sub L

Mackie SMR Sub R

Show

VenueVersion

Title

Drawn ByContact

A Midsummer Night’s Dream

The Loft, Kelvin GroveV1 as of 20/09/2018Archive Schematic

Benjamin Mills

Director

DesignersFrancesca Savige

Stephanie YauSet, Costume &Vision Designer

Nicholas SeeryLighting Designer

Benjamin MillsSound & Vision Designer/ QLab Operator

KEY NOTESSDI

XLR

- Not to scale.- Comms System hasn’t been drawn in.- Camera Placement refer to Camera Placement plan.- Power not drawn.- Footage from the Stage Feed cameras will be

recorded onto SD cards in the Hyperdeck Mini.- Audio from Zoom H6 willbe ercorded

Stage Feed

NT5

NT5 Zoom H6IN123

Comms

SOUND

Blackmagic ATEM TV Studio HD

N70

N70

N70SDI OUT

N70

Hyperdeck Mini

Hyperdeck Mini

Hyperdeck Mini

Hyperdeck Mini

SDI IN

1

2

3

4

SDI OUT

SDI OUT

SDI OUTSDI OUT

5

6

7

8

VIDEO Stage Feed

Subject to Change Correct as of 24/10/2018 Ben Mills | Sound & Vision Designer / Qlab Operator

Version 2Page 1 of 3

A MIDSUMMER NIGHT’S DREAM SOUND & VISION EQUIPMENT LIST

Version #2

Quanity Item Hirer Pickup Date Return Date Department

1 MacBook Pro Ben Mills 3/10/18 22/10/18 SND

1 MacBook Air Ben Mills 3/10/18 22/10/18 VIS

1 Zoom H6 Handy Recorder Nick Seery 3/10/18 22/10/18 ARCH

1 GoPro Hero 5 Black Ben Mills 3/10/18 22/10/18 ARCH

1 Panasonic DZ21K with ET-D75LE10 QUT Gardens Theatre 3/10/18 22/10/18 VIS

1 5 meter SDI Cable QUT Gardens Theatre 3/10/18 22/10/18 VIS

3 10 meter SDI Cable The Loft 3/10/18 22/10/18 ARCH

1 Soundcraft Expressions 1 The Loft 3/10/18 22/10/18 SND

2 Shure Wireless ULXD SM58 The Loft 3/10/18 22/10/18 SND

1 Shure ULXD4D Receiver The Loft 3/10/18 22/10/18 SND




Version #2

2 Mackie SRM450 The Loft 3/10/18 22/10/18 SND

3 Mackie SRM Subwoofer The Loft 3/10/18 22/10/18 SND

1 TRS - XLR Loom The Loft 3/10/18 22/10/18 SND

4 Camera Tripods Z6 ELC 2/10/18 22/10/18 ARCH

4 Sony NX70 Z6 ELC 2/10/18 23/10/18 ARCH

2 Rode NT5 Z9 Level 1 ELC 3/10/18 22/10/18 ARCH

1 Rode NTG3 Z9 Level 1 ELC 3/10/18 22/10/18 ARCH

1 Blackmagic ATEM TV Studio HD Z9 Level 1 ELC 3/10/18 22/10/18 ARCH

4 Blackmagic Hyperdeck Mini Z9 Level 1 ELC 3/10/18 22/10/18 ARCH

1 Mac Mini w/ Motu 16a (Qlab 4 installed) Z9 Level 1 ELC 3/10/18 22/10/18 SND

2 Monitor w/ Keyboard and Mouse Z9 Level 1 ELC 3/10/18 22/10/18 SND

1 DIN21 - SDI Z9 Level 1 ELC 3/10/18 22/10/18 VIS

1 Cisco Network Switch (10 port) Z9 Level 1 ELC 3/10/18 22/10/18 VIS

1 TP-LINK Wireless Router Z9 Level 1 ELC 9/10/18 22/10/18 SND




Version #2

1 Mac Pro (Qlab, Decklink Quad Installed) Z9 Level 1 ELC 3/10/18 22/10/18 VIS

5 Ethernet Cables Ben Mills 3/10/18 22/10/18 VIS

Subject to Change Correct as of 25.10.18 Ben Mills | Sound & Vision Designer


A MIDSUMMER NIGHT’S DREAM Sound Patch Sheet

Version #2

Audio Patch Sheet – QLAB, Motu, Sound Craft SI Expression 1

Channel # Name MOTU Outputs Sound Craft

Inputs Sound Craft

Outputs Venue Patching -

Control Venue Patching -

Floor

1 FOH LEFT 1 1 1 AMP 2/Chan 1 N/A 2 FOH RIGHT 2 2 2 AMP 2/Chan 2 N/A 3 REAR LEFT 3 3 3 AMP 1/Chan 1 N/A 4 REAR RIGHT 4 4 4 AMP 1/Chan 2 N/A

5 SUB L 5 5 5 SP12 - MIC 2 SP12 - AUD 2

SUB L (2) N/A N/A N/A N/A N/A 6 SUB R 6 6 6 SP14 - MIC 2 SP14 - AUD 2 7 ATMOS LEFT 7 7 7 SP12 - MIC 1 SP12 - AUD 1 8 ATMOS RIGHT 8 8 8 SP14 - MIC 1 SP14 - AUD 1

9 WIRELESS MIC (PRI) N/A 9 9 RT1 N/A

10 WIRELESS MIC (RED) N/A 10 10 RT2 N/A

11 GOD MIC N/A 11 11 N/A N/A



A MIDSUMMER NIGHT’S DREAM Vision Patch Sheet

Version #2

Vision Patch Sheet – Decklink Quad 2, QLAB, Panasonic PT-DZ21K

SOURCE IN OUT SURFACE

Panasonic DZ21K SDI IN DECKLINK QUAD 2 #8 Surface #1 Back Wall


Version 2 Page 1 of 1

SHOW NAME DOCUMENT TITLE

Version #

A MIDSUMMER NIGHT’S DREAM NETWORK ALLOCATION

Version #2

Machine IP Address

Vision Mac Pro 192.168.10.161

Sound Mac Mini 192.168.10.162

Panasonic DZ21K Projector 192.168.10.160

Sound Designer 192.168.10.167

Vision Designer 192.168.10.169

Ben Mills | Sound & Vision Designer Subject to Change Correct as of 2.10.18 Version 2 Page 1 of 1

SHOW NAMEDOCUMENT TITLE

Version #

A MIDSUMMER NIGHT’S DREAM Communication Allocation

Version #2

If there are any issues or concerns with the current comms allocations, please see Ben Mills (Sound & Vision Designer/ QLab Operator).

Personnel Comm's Pack Number Plot Tech/Dress Show Production Stage

Manager 1 x x x

Assistant Stage Manager 2 x x x

Head LX/ Lighting Designer 3 x x x

Lighting Operator 4 x x x

Sound & Vision Designer / QLab

Operator 5 x x x

Set, Costume & Vision Designer 6 x x x

Head of Set 7 x x x Lecturer 8 x x x

Duty Tech 9 x x x

Control Room PS RailOP Rail

11800

2498 2498

Notes Key - Mackie SRM450's to face the Upstage wall.

D - Mackie SRM Sub to face downstage. JBL Control 30 D Mackie SRM Subwoofer

[ Mackie SRM450

TITLE: Speaker Section Sound Designer: Ben Mills

Version: V3 as of 12/10/2018 Venue: The Loft, Kelvin Grove

Drawn by: Ben Mills Mobile:

Scale: 1 :50 @ A3

Control RoomPS RailOP Rail

Rear Rail

Notes

- Aspect Ratio: 16:1 0 - Surface Dimensions: 1920 x 1040.

- Lens: ET-O75LE10 1.3 - 1.7:1 - Surface dimensions: 11800mm x 7400mm...

e

Title: Vision Section Drawn by: Ben Mills

v- r-s_i a_n:_v_3_a_s_ot_1_21_1_0 1_20_ 1_a ...

- Projector: Panasonic PT-DZ21 K - Projector will sit on a black wooden box

- Distance from liens to surface: 18.25 m in the centre of the bio box.- Projector surface is the upstage wall. - Projector not drawn, only beam.

Venue: The Loft, Kelvin Grove Emai

Vision Designers: Stephanie Yau & Ben Mills




Version #

A MIDSUMMER NIGHT’S DREAM Archival Procedure

Version #2

Time-lapse

You MUST Format the SD Card before each Recording

STARTING THE TIME-LAPSE

Step One: Format SD Card 1. Turn on Go Pro by holding the button on the side down.2. Swipe down from the top of the screen to reveal the menu.3. Click on “Preferences” and scroll down to “FORMAT SD CARD”4. Select this, and press “OK”

Step Two: Selecting Time-Lapse Mode 1. As default, once the Go Pro is turned on I have configured it to be ready to

start Time Lapsing (photo) at 30 seconds.2. Press the Mode (side button) button until the Time-Lapse screen appears.3. Select “Time-Lapse Photo”, ensure settings are set to “30 Seconds” and

“12mp”4. Press the mode button to escape once settings have been set.

Step Three: Plug in Go Pro to GPO 1. Plug the Go Pro charging cable (USB-A to USB Type C) into the Go Pro with

the USB C termination going into the camera.2. Plug the charger into a GPO located on the Bio Box desk near the projector.

Step Four: Positioning of Go Pro 1. Place the Go Pro in the position, closest to the silver lip on the edge of the bio

box desk.2. Ensure the power cable is still in place once the Go Pro has been positioned,

make sure the Go Pro will not move during the time-lapse.

END OF TIME-LAPSE

1. Press the recording button (top button) on the Go Pro to stop its recording.2. Power off the Go Pro, hold down the side button.3. Take Go Pro out of its housing, import footage via the USB-C cable.4. Import all footage onto LaCie HD (Ben Mills) in the Archive folder, and then

into corresponding subfolders (bump in, focus, plot etc.)




Version #


Version #2

Show Recording

Pre-show 1. See show plot for power up sequence.2. For All three of the Blackmagic Hyperdeck minis ensure that all are

set to record as H624 Medium.3. Format the SD cards in both the Hyperdecks minis and in the

Zoom H6 Recorder.

Beginners 1. Start recording on all three Blackmagic Hyperdeck minis by

pressing the record button, each Hyperdeck will record on of thefollowing OP Stage Camera, C Stage Fee Camera and PS StageCamera.

2. Start recording on the Zoom H6 which will record the stage feedaudio (left and right) and comms recording.

Post Show 1. Stop recording on all devices. Hyperdecks, this is done by using

the STOP button on each device. Zoom H6 Recorder, this is doneby pressing the stop button.

Post Show After FOH Clearance

1. Stop the Zoom H6 recording for the stage feed and commsrecording. Bring SD Card down to the green room to importcontent into the LaCie HD (Ben Mills).

2. Stop all recording on cameras #1-3, on the Hyperdecks, this isdone by using the STOP button on each device.

3. Import all footage onto the Archive HD into the appropriate folders,(Show, Camera, Comms Recording etc).

4. Once confirmed that all footage has been backed up to the ArchiveHD format all the SD Cards.




Version #


Version #2

Comms Recording Announcement

Ladies and Gentlemen of the A Midsummer Night’s Dream Company. Please be advised that comms and archival recording will commence shortly, comms and archival recording will commence shortly. Thank you

Ladies and Gentlemen of the A Midsummer Night’s Dream Company, this is comms recording for A Midsummer Night’s Dream, Show Number #, 15/16/17/18/19/20th October, 2018. Please be advised that comms are now recording. Please be advised that comms are now recording.

Subject to Change Correct as of 20-Oct-18 Ben Mills | Sound & Vision Designer



Version #

A MIDSUMMER NIGHT’S DREAM SOUND & VISION DESIGNER / QLAB OPERATOR SHOW PLOT

Version #2

Two Hour Call: Power On:

- Vision:o Turn on the vision control power board which is connected to a technical earth

GPO. This power board has plugged in into it the Mac Pro, Monitor, NetworkSwitch, Blackmagic Decklink Quad 2.

o Power on the Projector that is used in the show, which is the Panasonic PT-DZ21K. The mains power button should be already in the ON position, press thePOWER ON button on the side of the projector for 3 seconds. Wait until theprojector starts to power up and continue with the power up sequence.

o Power on the Mac Pro by pressing the silver power button on the front of itshousing for 3 seconds until the mac start up sound can be heard.

o Turn on the monitor by pressing the touch sensor power icon on the front of thedisplay.

o Once the projector has powered up, check that the signal that the projector isbeing inputted is 1080/60i. A pop-up window will appear on the left-hand side ofthe surface.

o Open Blackmagic Desktop Video Setup on the Mac Pro.

o Click through until Decklink Quad (8) appears on the screen. From this click into itto check its settings.




Version #


Version #2

o Check that the Output Format is set to 1080i60.o Check that the Connector is set to SDI 8.

o Once this is all correct. Save and QUIT Blackmagic Desktop Video Setup. Makesure this is completely quit before opening the QLAB Show file.

§ If the projector isn’t recognising the input, check the following:• Make sure that the DIN21-SDI cable located at the back of the Mac

Pro in the Decklink Quad 2 is connected properly and isn’tdamaged.

• Make sure the connection from DIN21 – SDI to the SDI cable to theprojector is securely in place. As well as the SDI connection into theprojector itself.

• Make sure the projector is set to INPUT SDI 1 this can be checkedby going into MENU, scrolling down and selecting signal list, andchecking that the input the projector is receiving is SDI 1, at1080i60.

• If the projector is still not receiving any signal, quit Decklink andrestart the computer and power down the projector. Once all hasbeen powered down, wait at least 1 minute to give it some time,then power up the projector then the Mac Pro. This should resolvethe issue.




Version #


Version #2

o On the desktop open the Folder named “Show Files”o Open the file named “2018_QUTActing_MND_VisionShowFile_Bundle_V2

o Once this is opened, click on the setting icon and go into the VIDEO Tab.

o Click EDIT, on the Back Wall Surface which should be the only surface available.

o Open the surface setting and put up the grid. This is done by clicking the GRIDbutton.




Version #


Version #2

o Make sure that the projector is focused correctly to the edges of the wall andmake sure that the focus is correct.

o Once the grid is up and the focus is correct, unclick the GRID button and returnback to the main cue list.

o Check that QLAB has control of the shutter over the network. This is done bygoing on the Shutter Close Cue and Shutter Open Cue that is located in thePreshow Checks Cue List.

§ If this doesn’t work check that the ethernet cable that is in the projectorhasn’t come lose or unplugged.

§ Double check that the Network switch is powered on and the ethernetcables connected are plugged in correctly.

§ Check the IP Address of the projector and make sure it is 192.168.10.160.If this has changed, set it back to 192.168.10.160. To check this, on theprojector, using the button on the side, click MENU, then use the arrowdown button (with will be the top arrow because the projector has beenpositioned upside down due to restrictions on placement) until NETWORKis selected, click the ENTER button, scroll down until IP Address isselected and click ENTER and use the arrows to change the IP address.

SOUND: - Turn on all GPO’s that are on the desk of the bio box.- Power on the Mac Mini by pressing the power button.

o Open the folder Show file, and open the file“2018_QUTActing_MND_SoundShowFile_V3”

- Turn on the monitor by pressing the power on touch sensor on the front of the monitor.- Power on the MOTU 16A audio interface, by switching on the power switch (located on

the front right of the mac mini housing)- The sound console that is being used of MND is the Soundcraft SI Expression 1. Power

on the sound console by pressing the power button in and holding for 2 seconds. Theconsole will take a while to power on but whilst this is happening, turn on the FOH andREAR speaker AMPS. This is done by pressing the power buttons locating in the venuepatching rack at the bottom and turning the two amps labelled “REAR” and “FOH” ON.




Version #


Version #2

- Power on all Stage Audio, which consists of the three Subs and the two atmosspeakers, they are located in the upstage wall traps in the wall both OP and PS.

- Power on the ULXD4D rack which is located below the base station for Comms.- Turn on the base station (HME DX200) by pressing the power button.- Turn on the Show Relay which is located above the base station, by pressing the power

switch onto the ON position. Please note that the LED lights are broken and do not workbut if the switch is in the ON position, the show relay is on.

- Wireless Microphones:o The Wireless microphones that are used in the show are the ULXD SM58. There

are two of these used, on the desk Chan 9 is the Primary and Chan 10 is theSecondary. On the physical microphone the primary has been labelled for easeof locating it for the actors.

o Before each show the batteries MUST be changed with new fresh AA batteries.These batteries can be located in the Audio Cupboard.

o Each microphone requires two AA batteries.

- Sound Check:o Play the Preshow Check group in the show file. Mute channels 1 through 11 at

the desk and bring up each speaker and turn it on and check that sound iscoming out, then move onto the next speaker.

o Once this is done, press the RECALL button located above the master fader andrecall “MND18”.

- Hour Call:o Mic Check with Cast:

§ Once Ms Grima, is ready with the cast after fight call get Ms Tucker, MsPrice and Mr Carseldine to get ready for a Mic Check. Make sure thePrimary and Secondary microphones are switched on and are receivingsignal at the desk.

§ Turn on Chan. 9 on the desk and bring up the fader to -10db.§ Get cast to say a couple of their lines when they use the microphone and

make sure there is no feedback.o Once Mic Check is complete, get Ms Grima to turn off both microphones and

place them in there pre-set positions.- Archival

o Turn on the Blackmagic Video Switcher at the front of its housing which is locatedunderneath the projector.

o Put the SD card into SD 1 into each of the Hyperdeck Minis and Click MENU,then click SET, then use the wheel to scroll down to Format, click set, then selectSD1, then SET, then OX Extended, then set, then confirm that you are wanting toformat the SD card. Do this for all three SD cards.

o Power on the Cameras by opening the screens on the physical device in theseating bank.

o Make sure the ZOOM H6 Recorder (located on top of the switcher) has power.o Plug in the SD card and format it.

- 10 Minutes to Beginners:o Do the Archival Warning over comms.




Version #


Version #2

§ Ladies and Gentlemen of the A Midsummer Night’s Dream Company.Please be advised that comms and archival recording will commenceshortly, comms and archival recording will commence shortly. Thank you

Beginners: o Start recording on the three hyperdecks and the Zoom.o Do the Comms recording announcement over comms:

§ Ladies and Gentlemen of the A Midsummer Night’s Dream Company, thisis comms recording for A Midsummer Night’s Dream, Show Number #,15/16/17/18/19/20th October, 2018. Please be advised that comms arenow recording. Please be advised that comms are now recording.

During the Show: - When instructed by SM go into SND Q 0.5 (Preshow).- Shutter the projector when instructed by Head LX for Blackout check.- Respond to standby’s with Sound when SM puts up standbys.- When a MIC Q is called, press Chan. 9 ON and ride the fader up.- Write down any notes of nothing that went wrong during the show.

Power Down: - Once Front of House Clearance has been given, save the show file on both the Sound

Mac Mini and the Vision Mac Pro- Stop recording on the Hyperdecks and the Zoom.

o Take out all SD cards and start downloading content off them onto Archive LacieHardrive.

- Power down the projector by pressing the Standby button and then selecting the OKbutton.

- Power down the Mac Pro.- Power off all stage audio speakers and the FOH & REAR Amps.- Power down the audio sound console by press and holding the power button and

pressing it again. This will power down the console.- Turn off the wireless microphones and the ULXD40 Receiver.- Turn off the Comms base station.- Power off the vision power board.- All systems will have been powered down.

Subject to Change Correct as of 15/10/18 11:30 am Ben Mills | Sound & Vision Designer / Qlab Operator


A MIDSUMMER NIGHT’S DREAM SOUND CUE SYNOPSIS

Version #3

LEGEND:

BOLD = Cue Point

CUE Unit Page Cue Name Source Line/Blocking Notes SND Q 0.5

Preshow

- Pre-show TBC SM's Discretion W/ SHUT Close SND Q 0.7 - FOH Clearance TBC FOH Clearance

SND Q 1 1

Fade & Stop Pre-show - Front of House

Clearance. After song has finished

W/ VISQ Q 1 & SHUT Open Dream Sequence

- SpookyWind_V3.- RA by Slumberjack- AthensWorld_Atmos

2 1 Fade Up Atmos - AthensWorld_Atmos After Hippolyta wakes up.

SND Q 3 6 5 Door Open - DoorOpen_CreakyV1 VISQ: HELENA opens the fourth wall door.

SND Q 3.5 6 5 Door Slam Close -DoorSlamClose_V2 VISQ: as HELENA steps onto stage from stairs. MIC Q 1 7 6 MIC ON - Wireless SM58 W/ SND Q 3.5 Through FOH L & R

SND Q 4 7 7 Forest Fairy Theme - ForestFairyTheme_V3- ForestWorld_AtmosV1BOTTOM: Hold or cut bow strings! W/ VIS Q 2.5

MIC Q 2 8 7 MIC OFF - Wireless SM58 W/ SND Q 4

SND Q 4.5 8 7 Fade Out and scratch -ComedicScratch_V1 PUCK Entrance SNAP OUT

SND Q 5 8 8 Oberon Entrance -OberonEntrance_V2 PUCK: wanderer of the night. Rear R, Atmos R, Sub




Version #3

SND Q 5.5 8 8 TITANIA Entrance Sound -ForestFairyTheme_V2PUCK: here comes Oberon

SND Q 6 12 12 Fade Low Fairy Lullaby

-ForestFairTheme_V3

OBERON: "I know a bank."

SND Q 6.1 12 12 Fade Up Fairy Lullaby TITANIA Enters

SND Q 6.2 12 12 Fade Up Fairy Lullaby OBERON: Dances and delight.

SND Q 6.5 12 12 Fade Down Fairy Lullaby

COBWEB: Now all is well

SND Q 6.7 12 12 Cigarette Sound (breathing something) - CigaretteEnhale_V1VISQ: Flute put the cigarette in his mouth the right way.

SND Q 7 12 12 TITANIA Orgasm -TitaniaOrgasm_V4 OBERON: Wake when some vile thing is near W/ VIS Q 3.5

SND Q 8 13 12 Siri Response -SiriResponse_V2LYSANDER: …you faint with wandering in the wood

SND Q 9 14 13 Lysander Orgasm - LysanderOrgasm_V2 PUCK: Sleep his seat on thy eyelid w/ VISQ 4.5

SND Q 10 15 14 Glass Smash -GlassSmashWall_V1 VISQ: Lysander punches fourth wall on DSPS

SND Q 10.5 15 Bottom Transition into Donkey -BottomTransitionDonkey_V1

VISQ: When Bottom puts his foot up on rostra.

MIC Q 3 17 15 MIC ON - Wireless SM58 QUINCE Entrance




Version #3

MIC Q 4 17 16 MIC OFF - Wireless SM58 BOTTOM: Odours savours sweet

MIC Q 5 17 17 MIC ON - Wireless SM58 PUCK: I'll follow you, I'll lead you about a round… MIC Q 6 17 17 MIC OFF - Wireless SM58 PUCK: …at every turn.

SND Q 11 18 18 Bottom Dancing - Let's Get It On_V1 VISQ: PUCK presses remote button MIC Q 7 18 18 MIC ON - Wireless SM58 W/ SND Q 11 Will on Mic.

SND Q 11.5 18 18 Fade Down Bottom Dancing

- Let's Get It On_V1

TITANIA: What an angle... Fade Down

SND Q 11.7 18 18 Fade Up Bottom Dancing TITANIA: …from my flowery bed? Fade Up

SND Q 11.75 18 18

Fade Out Bottom Dancing

VISQ: Bottom falls over DSOP Long Fade

SND Q 12 18 18 Flying Moth -FlyingMoth_V1 TITANIA: Cobweb! Moth!

SND Q 12.5 18 18 Button Running into Fourth Wall -ButtomRunningIntoDoor_V1VISQ: Button runs DS into Fourth wall.

SND Q 13 19 19 Fade Up Rave Music

-RaveMusic_V1

PUCK: HOW NOW MAD SPIRIT

SND Q 13.2 19 19 Fade Out Rave Music VISQ: Oberon presses REMOTE




Version #3

SND Q 13.5 19 19 Fade Up Rave Music VISQ: Oberon presses REMOTE

SND Q 13.7 19 19 Fade Out Rave Music VISQ: Oberon presses REMOTE SND Q 14 19 20 Demetrius Orgasm -DemetriusOrgasm_V1 OBERON: remedy. W/ VIS Q 5

SND Q 15 22 25 Puck Boxing Ring -PuckBoxingRingV1 VISQ: PUCK getting angry.

MIC Q 7 22 25 MIC ON - VISQ: Puck picking up microphone, walking into rostra

SND Q 15.5 22 25 SLOWMO Boxing -PuckBoxingRingSlowmoV0 VISQ: Puck climbs into the Upstage Box.

SND Q 15.6 22 23 Fade Out PUCK Boxing Ring -PuckBoxingRingSlowmoV1

SND Q 15.7 22 26 Flower on Titania -FairyForestMusic_V1 PUCK: Gentle lover, remedy

MIC Q 8 22 26 MIC OFF - PUCK: and all things shall be well.

SND Q 16 23 26 Titania' Lap Dance

- Pony

PUCK: shall be well (beat)

SND Q 16.2 23 26 Fade Down Titania Lap Dance TITANIA: Come sit thee

SND Q 16.3 23 26 Fade Down and Stop Titania Lap Dance TITANIA: By gentle joy

SND Q 16.9 24 27 BIRD CALL -BirdCall_V1 PUCK: I do hear the morning lark.




Version #3

SND Q 17 28 30 Flute' Sad Leaf Blower - Only Time_V1

VISQ: As Flute enters from USPS W/ VIS Q 6.5

SND Q 17.5 28 30 Stop Flute' Sad Leaf Blower VISQ: Quince takes out Flutes earphones. Snap Out

SND Q 18 29 31 Grand Entrance Music -GrandEntranceMusic_V1VISQ: QUINCE presses remote. W/ VIS Q 7.5

MIC Q 8 30 32 MIC ON - Wireless SM58 QUINCE: If we offend... W/ SND Q 18.

SND Q 18.5 30 32 STOP Grand Entrance Music -GrandEntranceMusic_V1VISQ: QUINCE presses remote.

SND Q 19 30 32

Entrance Music -GrandEntranceMusic_V1

QUINCE: The actors are at hand

SND Q 19.5 Fade down Entrance Music VISQ: QUINCE presses remote.

SND Q 20

31 32

Entrance Music -GrandEntranceMusic_V1 W/ MIC Q 9

SND Q 20.5 WALL Theme

-WallTheme_V1 VISQ: Wall stomps her right foot onto rostra DS. Fade and stop Entrance music

SND Q 21 31 32

PYRAMUS Entrance Theme -

PyramusEntranceTheme_V2

VISQ: QUINCE presses remote.

SND Q 21.5 Stop Pyramus Theme VISQ: QUINCE presses remote.

SND Q 22 31 33

Thisbe Entrance Theme

- ThisbeEntranceTheme_V2


SND Q 22.5 Stop Thisbe Entrance Theme VISQ: QUINCE presses remote.




Version #3

SND Q 23 31 34

Lion Theme -LionTheme_Roar_V1


SND Q 23.5 Stop Lion Theme VISQ: QUINCE presses remote.

SND Q 24 31 34

Moon Theme -MoonTheme_V1


SND Q 24.5 Stop Moon Theme VISQ: QUINCE presses remote.

SND Q 26 31 34 Thisbe Theme - ThisbeEntranceTheme_V2


SND Q 26.5 Stop Thisbe Teme


SND Q 27

31 35

Pyramus Theme - PyramusEntranceTheme_V2


SND Q 27.5 Stop Pyramus Theme VISQ: QUINCE presses remote.

SND Q 28 Thisbe Theme - ThisbeEntranceTheme_V2


SND Q 28.5 Stop Thisbe theme VISQ: QUINCE presses remote.

SND Q 29 Glass Wall Smash - GlassSmashing_V1 VISQ: BOTTOM runs into the fourth wall DSPS.

SND Q 30 Thisbe Theme - ThisbeEntranceTheme_V2


SND Q 30.5 Stop Thisbe theme VISQ: QUINCE presses remote.




Version #3

SND Q 31

36

Grandfather Clock Chime

-GrandfatherClockChime_V1

THESEUS: Very notable discharged.

SND Q 31.5

Fade and stop Grandfather Clock PUCK: Tis only fairy

time" Fade low Fairy Lullaby -FairyForestMusic_V1

SND Q 32 32 37 Techno Rave

-RaveMusic_V1

PUCK: Now are frolic.

SND Q 32.5 32 37 Slow-mo Techno Rave TITANIA: Now, until the break of day.

SND Q 33 32 37 Build up Techno Rave TITANIA: Trip away

SND Q 34 32 37 Fade Out Techno Rave. W/ mic drop voom sound.

TBC TITANIA: break of day

MIC Q 16 32 37 MIC OFF - Wireless SM58 W/ SND Q 34

VISQ 8.5 32 37 VISQ 8.5 - Particles Dissolve VIS CONTROL MAC PRO PUCK: Shall restore amends." W/ SHUT Q (Close)

SND Q 35 Post show 37 Post show - Run the World Girls

VISQ: After bows TITIANIA presses remote button.

Post show Music TBC



A MIDSUMMER NIGHT’S DREAM APRA APPLICATION

Version #1

APRA SONG ID

(GW CODE)

SONG (Musical

Work)

COMPOSER(s) (Arranger – if applicable)

PERFORMER(s) DURATION (to be used)

00:00

PUBLISHER (office use

only) GW24012401 ONLY TIME BRENNAN E/RYAN N/RYAN R ENYA 01:00

GW15169885 MY HEART WILL GO ON

HORNER J/JENNINGS W CELINE DION 00:30

GW14869458 I’M KISSING YOU WEEKES D/ATACK T Des’ree 01:00

GW17404752 BELIEVE HIGGINS B/TORCH S/BARRY P Cher 00:30

GW36509311 I KISSED A GIRL /HUDSON K/GOTTWALD L/DENNIS C/SANDBERG M Katy Perry 00:30

GW43363438 DIAMONDS LEVIN B/ERIKSEN M/FURLER S/HERMANSEN T Rihanna 00:30

GW23927679 I’M COMING OUT RODGERS NILE GREGORY Diana Ross 00:30

GW00360345 I WILL SURVIVE FEKARIS D/PERREN F GLORIA GAYNOR 00:30

GW26172320 RESPECT COLES/DIGGS/HAWKINS/HUNTER/JONES/WOODS/S ARETHA FRANKLIN 00:30

GW01061651 YOU DON’T OWN ME

MADARA J/WHITE D GRACE 00:30

GW02766131 SISTERS ARE DOIN’ IT FOR THEMSELVES

LENNOX A/STEWART D EURYTHMICS

00:30

GW01069269 LETS GET IT ON TOWNSEND E/GAYE M MARVIN GAYE 00:45

GW12128864 PONY MOSLEY T/LUMPKIN E/GARRETT S GINUWINE 00:45

GW44740641 ROAR PERRY/MCKEE/GOTTWALD/WALTER/SANDBERG KATY PERRY 00:45



A MIDSUMMER NIGHT’S DREAM APRA DURATION

Version #1

APRA SONG ID

(GW CODE)

SONG (Musical

Work)

COMPOSER(s) (Arranger – if applicable)

PERFORMER(s) DURATION (to be used)

00:00

PUBLISHER (office use

only) GW24012401 ONLY TIME BRENNAN E/RYAN N/RYAN R ENYA 01:00

GW49902588 RA EHLERS F/THEN Y SLUMBERJACK 00:30

GW01069269 LETS GET IT ON

TOWNSEND E/GAYE M MARVIN GAYE 00:45

GW12128864 PONY MOSLEY T/LUMPKIN E/GARRETT S GINUWINE 00:45

GW44740641 ROAR PERRY/MCKEE/GOTTWALD/WALTER/SANDBERG KATY PERRY 00:45

GW24012401 ONLY TIME BRENNAN E/RYAN N/RYAN R ENYA 01:00

Subject to Change Correct as of 15/10/2018 Ben Mills & Stephanie Yau | Sound & Vision Designer / Set, Costume & Vision Design


A MIDSUMMER NIGHT’S DREAM VISION CUE SYNOPSIS

Version #3

CUE Unit Page Cue Name Line/Blocking Notes SHUT Q 1 Preshow 1 Shutter Close With SND Q 0.5 SHUT Q 2 Preshow 1 Shutter Open VIS Q: As Pre-show song finishes

VIS Q 1 1 1 Dream Sequence With SND Q 1 Athens World

VIS Q 2 7 7 Transition into Forest With SND Q 4 - Bottom: Hold or cut bow strings!'

VIS Q 3 12 12 TITANIA orgasm With SND Q7 - OBERON: Wake when some vile thing is near

VIS Q 4 14 13 Lysander orgasm With SND Q9 - PUCK: …on thy eyelid

VIS Q5 19 20 Demetrius orgasm With SND Q14 - Oberon: Beg of her for remedy

VIS Q6 28 31 Return to Athens World VIS Q: As mechanicals exit

VIS Q7 29 Athens into Pyramus & Thisbe With SND Q18

VIS Q 7.5 32 37 Vision fade out (Snap) PUCK: Shall restore amends.

SHUT Q 3 32 37 Shutter Close With SND Q35

2018_QUTActing_MND_SpeakerSection_V3.pdfSht-2 [Speaker Section V2]1/Sht-2

2018_QUTActing_MND_VisionPlacementPlan_V3.pdfSht-1 [Sheet Title]4/Sht-1

2018_QUTActing_MND_VisionSection_V3.pdfSht-1 [Sheet Title]4/Sht-1

Documents

Sound & Vision Bible...Crown XLS 602 #1 IN 1 2 OUT 1 2 FLOOR AUDIO JBL Control 30 REAR R JBL Control 30 FOH L JBL Control 30 FOH R Mackie SMR Sub L Mackie SRM450 ATMOS L Mackie SRM450