Upload
marcos-silva
View
284
Download
14
Tags:
Embed Size (px)
Citation preview
Lubrication is our World
Special Lubricantsfor Textile Machinery
2
Note: The overview of our partner companies from the textile machine sector shown on pages 4and 5 is not exhaustive.
For the next edition of this brochure, we will be pleased to include in this list the logo of othertextile machine and component manufacturers cooperating with us in the generation of lubri-cant recommendations for textile machine operators.
Contents Page
1.0 Introduction 3
Lubricants for:2.0 Preparatory and spinning machines (staple fibres) 6-73.0 Spinning machines (staple fibres) 8-94.0 Synthetic fibre spinning machines (filaments) 10-115.0 Synthetic fibre processing machines (filaments) 12-136.0 Twisting and spool winding machines 14-157.0 Apparatuses, accessories and special machines 16-178.0 Knitting machines 18-199.0 Warp knitting machines 20-21
10.0 Sizing machines and looms 22-2311.0 Textile finishing machines 24-2912.0 Gear units and electric motors in textile machines 30-3113.0 Lubricants for compressors in the textile industry 32-33
14.0 Product survey14.1 Lubricating oils 34-3514.2 Release agents 3614.3 Lubricating greases 36-3814.4 Lubricating pastes 3914.5 Solid lubricants 39
ALTEMPALTEMPANBARRIERTAFORMINOLGRAFLOSCONHOTEMPISOFLEXKlüber MadolKlüberoil TEXKlüberpasteKlüberplex
Klüber SilvertexKlüberspeedKlüberquietKlüber SummitKlübersynthKlübertempLAMORAMICROLUBEMOLYBKOMBINPARALIQPETAMO
PRIMIUM FLUID SPECIALQUIETSCH-EXSTABURAGSSTRUCTOVISSYNTHESOTEX SYNTHESOUNIMOLYUNISILKONWOLFRACOAT
are registered trademarks of Klüber Lubrication München KG
3
1.0
The operation of modern-day, high-performance textile
machinery involves a multitude of lubrication requirements
which standard lubricants can meet only partly, if at all.
The German Standard DIN 64 921, “Lubricants for textile
dyeing and finishing machinery”, provides a general listing
of only two lubricating greases based on mineral oils, plus
some lubricant groups (e.g. lubricating and hydraulic oils)
and adhesive lubricants on a mineral oil basis, together
with the corresponding standard code letters. This does
not yet amount to overall application engineering guidelines
and standardization options.
Formulating these is rendered more difficult by the
extremely wide variety of different friction points, with their
very different stresses and environmental conditions. It is
here that special lubricants come into their own.
At Klüber Lubrication, application-tailored solutions involv-
ing special lubricants for highly stressed friction points in
textile machinery have a long tradition. All over the world,
machine manufacturers and users can benefit from high-
quality lubricants of proven efficiency. Special lubricants,
when properly selected and utilized, not only improve oper-
ational reliability, they also cut maintenance costs sub-
stantially. The very high sums which still have to be spent
on correcting damage caused by friction and wear can be
effectively reduced by the use of special lubricants. In this
context it is of course of crucial importance to choose the
right lubricant – this is the key to successful lubrication. The
choice of a lubricant must be governed by the technical
and operational requirements profile of the friction point
involved and not primarily by the costs. The performance
and functional reliability of the lubricant are much more
important than a price per pound comparison showing the
supposed advantages of “cheap lubricant purchasing”.
High-quality special lubricants, though they may cost more,
are more economical for you in the long run.
Lubrication and lubricants are today more than ever the
subject of meticulous scrutiny by engineers and materials
planning staff. But special lubricants also make an impor-
tant contribution to reducing environmental pollution; often
only small quantities are needed to provide long-term or
lifetime lubrication in cases where total-loss lubrication
would not only be uneconomical but would also involve
substantial environmental difficulties.
In this brochure we present “intelligent” solutions for the
highly stressed friction points found in textile machinery,
restricting ourselves, of course, to the most important and
widespread cases of typical applications.
Technical development, however, is never at a standstill;
and we will always welcome your suggestions for expand-
ing and supplementing this brochure.
On the following pages, you will find details of typical appli-
cations and solutions to lubrication problems involving the
following types of textile machinery:
• Spinning machines
• Synthetic fibre spinning machines
• Synthetic fibre processing machines
• Twisting and spool machines
• Apparatuses and special machines
• Knitting machines
• Sizing machines and looms
• Textile finishing machines
All Klüber products recommended are high-performance
lubricants, most of them on a synthetic basis.
They offer:
• maximum operational reliability
• low machinery servicing costs
• long maintenance intervals
• environment-friendly utilization
For detailed descriptions of the products, with additional
information on the applications involved, please consult the
appropriate product information leaflets, which you can
obtain from us free of charge.
Please note that due to the extraordinarily large number
of technical solutions possible, the illustrations in this
brochure do not in each and every case relate directly to
the lubricant recommendations accompanying them. They
are intended merely as examples; the operating and main-
tenance instructions of the machine manufacturer as well
as the lubricant recommendations are of course binding.
Our network of production and sales companies all over
the world ensures that you always have a supplier of our
products conveniently near to you, who will also keep you
up-to-date with the latest results from research, develop-
ment and testing.
Introduction
4
GTM
Tessili Impianti
Klüber Lubrication – Partner of Textile Industry
5
6
2.0
Example Machine / Component Lubrication Problem / Requirements
Rotary plate (plain bearings) in carders anddrawing frames
Top and bottom drawingroller bearings in drawframes
Rolling bearings in thedrawing assembly(ring spinning frame)
Top roller bearings(ring spinning frame)
Frequent maintenance
High bearing temperature, danger of contamination of
the spinning material (sliver) in the can
Insufficient bearing life if lubricated with standard
greases
Overheating of bearings
“Bearing bleeding”
Excessive separation of the oil from the grease in the
bearings, necessitating frequent relubrication
Lubricants for Preparatory and Spinning Machines
7
Staple fibres
Klüberpaste 46 MR 401
Modern white multi-purpose
lubricating paste
or
ALTEMP Q NB 50
Well-proven, light-coloured lubri-
cating and assembly paste
ISOFLEX TOPAS NB 52
Fully synthetic special grease for
high-speed needle bearings
or
STABURAGS NBU 12 / 300 KP
STABURAGS NBU 12 / 300 KP
Special high-pressure grease with
excellent long-term effectiveness
Long-term lubrication lasting for
weeks; minimized contamination and
low-wear operation
Klüberpaste 46 MR 401 or
ALTEMP Q NB 50 should be in every
workshop since, being an assembly
paste, they protect against fretting
corrosion.
Relubrication intervals may exceed the
recommended intervals by far.
ISOFLEX TOPAS NB 52
is recommended by Messrs. Vouk for
older machine types.
Rieter / Ingolstadt uses
ISOFLEX LDS 18 SPECIAL A for initial
lubrication and lists it in the lubricant
recommendations.
Excellent corrosion protection and
long-term lubrication of bottom roller
bearings (needle bearings)
On top rollers (deep groove ball bear-
ings) a service life of several years
without relubrication is achievable.
STABURAGS NBU 12 / 300 KP has
been used for initial lubrication for
example by Spindelfabrik SUESSEN
for many years.
Recommended Lubricants Advantages Notes
8
INA
3.0
Example Machine / Component Lubrication Problem / Requirements
Needle bearings in bottom drawing rollers(ring spinning frame)
OE spinning turbines(direct or TwinDisc drive)
Opening rollers(OE spinning frame)
Extensive maintenance in case of bearing failure, thus
long-term lubrication required
Extremely high speeds
Overheating and wear of the bearing
Too frequent relubrication
Bearing wear may lead to uneven opening
of the sliver.
Lubricants for Spinning Machines
9
Staple fibres
STABURAGS NBU 12 / 300 KP
Special high-pressure grease with
excellent long-term effectiveness
Klüber high-speed lubricants for
open-ended spinning turbines,
opening and pressure rollers
ISOFLEX NBU 15
ISOFLEX NCA 15
ISOFLEX LDS 18 SPECIAL A
Depot and relubricating oil for
Rieter OE machines
ISOFLEX PDP 65
ISOFLEX NBU 15
Besides long-term lubricity, very good
corrosion protection
Low maintenance requirements
Long-term lubrication
Increased operational reliability and
extended bearing life with very long
relubrication intervals
The Klüber high-speed lubricants
listed are recommended by leading
rotor manufacturers.
The range of lubricants is continuously
adjusted to keep up with development
trends in the rotor manufacturing
sector.
Higher operational reliability ensures
flawless opening of the sliver.
Recommended Lubricants Advantages Notes
10
4.0
Example Machine / Component Lubrication Problem / Requirements
Spinning pumps
Spinerets
Godet bearings
Pre-heating temperature 260 °C to 280 °C
Start-up problems due to deficient oil film
or oil residues
Difficulty in dismantling spinerets after long produc-
tion runs, caused by seized screw threads
Clogging of the fine nozzles in the spineret plate
results in malfunctions and delays in production.
“Bleeding” of the grease results in impeded bearing
operation.
Relubrication intervals too short
Lubricants for Synthetic FibreSpinning Machines
11
Filaments
From the
UNISILKON TK 017 THERM oil
series
Essential for testing and start-up of
precision gear pumps in the melt
spinning process
Klüberpaste HEL 46-450
or
WOLFRACOAT C
Well-proven hot screw thread
compound
UNISILKON TK 44 N 2 REC. A
UNISILKON L 50/2
BARRIERTA L 55/2
Excellent rolling bearing greases
with high thermal stability for long-
term lubrication
PETAMO GHY 441
Uniform viscosity for exact metering
adjustment and precise delivery
Low evaporation and sufficient resid-
ual oil for the start-up lubrication of
preheated pumps
Separating effect towards many
synthetic materials
The UNISILKON TK 017 THERM oils
are recommended e.g. by pump man-
ufacturers and successfully used by
numerous synthetic fibre processors.
Protection against seizure of spinerets
Easy removal
Easy dismantling of the spinerets
Klüberpaste HEL 46-450 and
WOLFRACOAT C are suitable for hot
screw threads up to 1200 °C.
Long-term lubrication and improved
bearing life under extreme conditions
Lubrication acc. to OEM recommendation,
e.g. by Starlinger
< 150 °C, PETAMO GHY 441
150 – 170 °C, BARRIERTA L 55/2
or Barmag: up to 180 °C
UNISILKON TK 44 N 2 REC. A
up to 200 °C: UNISILKON L 50/2
(cooperation: Starlinger – Windmöller + Hölscher)
Klübersynth BH 72-422
Recommended Lubricants Advantages Notes
UNISILKON M 2000-SPRAY
Effective separating lubricant for
polymers during spinning start
No clogging of the spinerets and
secure start-up of production at tem-
peratures up to 180 – 200 °C max.
UNISILKON M 2000-SPRAY is a uni-
versal separating lubricant for thermo-
plastics and duroplastics as well as
elastomers and is also suitable as a
sliding agent for seals.
12
5.0
Example Machine / Component Lubrication Problem / Requirements
Cold and hot separator rollers
Spinning rings(sintered metal)
Thread breakage on fine denier caused by dragging
rollers; frequent maintenance
Production losses
Traveller and ring wear
Uneven or excessive yarn tension as well as lubricant
starvation
Filament coiling(after drawing)
High bearing loads resulting from high speeds up to
14,000 rpm
Lubricants for Synthetic FibreProcessing Machines
13
Filaments
ISOFLEX SUPER LDS 18/25 S
Lubricant dispersion system for
long-term lubrication
SYNTHESO XOL 12
Synthetic oil with an extraordinary
performance spectrum
Extremely smooth running, thus no
thread breakage; ensures years of
maintenance-free operation.
ISOFLEX SUPER LDS 18/25 S is a
CFC-free long-term lubricant (disper-
sion). Observe the solvent’s extended
evaporation period during relubrica-
tion.
Very low wear rates
Reduced yarn tension and optimum
distribution on the friction points
SYNTHESO XOL 12 is also suitable
for the lubrication of compressed air
tools.
Recommended Lubricants Advantages Notes
ISOFLEX NBU 15
One of Klüber’s high-speed lubri-
cants that is being successfully
used worldwide
High operational reliability ensures
accurate coiling of the filament.
Filament coiling bearings are initially
lubricated with ISOFLEX NBU 15 by
Neumag.
14
6.0
Example Machine / Component Lubrication Problem / Requirements
Thread guide slides andzig-zag winding guides
Travelling knotter/splicer(Schlafhorst Autoconer®)
Spindle can bearing(see photo)
Belt guide rollers(no photo)
Wear
Yarn staining due to lubricant splashes
Excessive frictional temperature and
power requirement
High mechanical stress
Wear
Friction points difficult to access
Splicer(also knotter)
Flawed operation due to fibre build-up, contaminants
Impaired sliding effect
High energy consumption
Short relubrication intervals
Excessive frictional resistance of the grease
Impeded operation of guide rollers
Lubricants for Twisting and Spool Winding Machines
15
ISOFLEX TEL 3000 ALTEMP
Dynamically very light grease with
emergency lubricating properties
imparted by a light-coloured solid
lubricant compound
MOLYBKOMBIN M 5-SPRAY
Molybdenum disulphide lubricating
oil concentrate ensuring high wear
protection and emergency lubricat-
ing properties
UNIMOLY PLUS
Assembly paste for maintenance
operations
ISOFLEX LDS 18 SPECIAL A
Dynamically light synthetic grease
for long-term or even lifetime
lubrication
STABURAGS N 4
A smooth running grease offering
an alternative to the above product
PETAMO GHY 133 N
Temperature reduction due to less
friction
Long maintenance intervals
Clean lubrication
ISOFLEX TEL 3000 ALTEMP
is also suitable for thread guide
rails/boxes on flat bed knitting
machines.
Easy application by spraying
High protection against wear
Long-term effect
UNIMOLY PLUS for the ball cups on
the swivelling device, generally for the
lubrication of all sliding points and
connections after overhauling
MOLYBKOMBIN M 5-SPRAY is
approved for the lubrication of the
internal mechanism in the housing of
travelling knotters. It is also used for
the internal mechanism of the spool-
ing equipment and for gears in the
gear reducer unit of the travelling
splicer or travelling knotter.
Substantial reduction of power
requirement
Extended relubrication intervals of
5000 h or more
Relubrication interval: up to 10,000
operating hours
ISOFLEX LDS 18 SPECIAL A
is a special grease for high speeds
ensuring uniform speed.
STABURAGS N 4
ensures low-friction guiding of drive
belts.
Recommended Lubricants Advantages Notes
QUIETSCH-EX SPRAY
is a low-viscous lubricant, corro-
sion protective and rust removing
agent.
Preventive maintenance with a com-
bined cleaning and oil spray. The ultra-
thin oil film ensures the necessary
wear protection, excellent surface
wetting and protection against corro-
sion.
QUIETSCH-EX SPRAY
is also used for guide bars on knitting
machines and for the Jacquard nee-
dles of looms.
An ultra-thin layer ensures efficientlubrication.
16
7.0
Example Machine / Component Lubrication Problem / Requirements
Lid seals of dyeing vessels(see photo)
and
yarn steamers(no photo)
Worm gear of overheadtravelling cleaners
Sticking of rubber seals results in excessive seal wear.
Excessive temperature due to high frictional heat
Lubricant leakage
Contamination and severe wear
Lubricants for Apparatuses and Special Machines
17
SYNTHESO PROBA 270
Fully synthetic grease with neutral
properties towards natural and
synthetic rubber
STRUCTOVIS P LIQUID
Synthetic, intrinsically viscous lubri-
cant improving gear efficiency
Due to the sliding film the lids open
and close easily and the seals reach
an extended service life.
Seal relubrication only required weekly
SYNTHESO PROBA 270
The water and steam resistant grease film
is also an ideal assembly aid for all rubber
seals and in the finishing section.
For lubricating bearings in the washing
liquor circulation pumps,
STABURAGS NBU 12/300 KP (Thies)
or
PETAMO GHY 133 N (Then) are recom-
mended
Prevents leaks on shaft seals.
Low gear temperature, suitable for
long-term lubrication
STRUCTOVIS P LIQUID
is recommended for gearboxes that
are not oil-tight.
Recommended Lubricants Advantages Notes
18
8.0
Example Machine / Component Lubrication Problem / Requirements
Needles and sinkers in circular knittingmachines
Flat bed knittingmachines
Application in stitch-
forming elements
Slide rails on flat bedknitting machines,thread guide box
Overheating in the knitting section
Production malfunctions caused by wear resulting in
formation of stripes as well as problems due to insuffi-
cient scouring of the textile machine oils from the knit-
ted fabrics
Neutral towards elastane fibres and elastomers
Hosiery knittingmachines
Application in
stitch-forming elements
and gears
Temperature increase in high-speed machines, along
with increased wear
Neutral towards elastane fibres and elastomers
Drops or splashes of lubricant caused by the sudden
arrest of the thread guide box on reaching its stop as
well as frequent dragging motion
Lubricants for Knitting Machines
19
Running-in oil:Klüber Silvertex P 91
Needle oil:Klüber Silvertex W 22/W 32Klüber Silvertex T 22/T 32Klüberoil TEX 1-22 N/1-32 N
Cleaning oil:Klüber Silvertex R 14/R 20
Running-in oil:Klüber Silvertex P 91
Needle oil:Klüber Silvertex W 32Klüber Silvertex T 32/T 46Klüberoil TEX 1-32 N/1-46 N
Cleaning oil:Klüber Silvertex R 14/R 20
Klüber Silvertex GREASE 3000 N
ISOFLEX TEL 3000 ALTEMP
Light-coloured, soft sliding greases
replacing oil lubrication
Klüber needle oils reduce the operat-
ing temperatures and protect against
wear and corrosion of the stitch-form-
ing elements, thus reducing mainte-
nance costs of production machines.
They are scourable and neutral
towards elastane fibres and elas-
tomers. Klüber needle oils have been
tested and approved by knitting
machine manufacturers worldwide.
For instance, they are used for initial
lubrication by Mayer & Cie., Terrot,
Stoll and Universal.
There is no universal method to
remove oil stains from the different
types of knitting materials or fibre
mixtures. In consequence, close
cooperation between the knitting and
the finishing sections is required when
selecting a suitable detergent.
Relubrication is usually necessary only
once a week and looping of the thread
is avoided in Jacquard equipment.
Klüber Silvertex GREASE 3000 N
ISOFLEX TEL 3000 ALTEMP
for slide rails where smooth sliding
operation is of primary importance
Recommended Lubricants Advantages Notes
Running-in oil:Klüber Silvertex P 91
Needle oil:TEX SYNTHESO M 32 NTEX SYNTHESO M 46 NKlüber Madol 172Klüber Madol 183
Cleaning oil:Klüber Silvertex R 14Klüber Silvertex R 20
20
9.0
Example Machine / Component Lubrication Problem / Requirements
Friction gears
Guide bars in warp knitting machines
Insufficient traction, non-uniform operation of the gear
Contamination of fabrics and frequent maintenance
work between warp beam changes resulting from
insufficient adhesion and insufficient life of the lubri-
cant film
Lubricants for Warp Knitting Machines
21
FORMINOL DS 23 K
or as a synthetic, long life oil and
super traction fluid
LAMORA VARIOGEAROIL EL 2
QUIETSCH-EX SPRAY
for flat bed frames
and
Klüberpaste 46 MR 401
or
ALTEMP Q NB 50
for ball joint bushes
These gear oils ensure optimum gear
operation, thus allowing precise
thread feed and fabric take-up.
They are indispensable for producing
top-quality fabrics.
FORMINOL DS 23 K and
LAMORA VARIOGEAROIL EL 2
are recommended by the leading
machine manufacturers.
The performance of these lubricants
lasts at least from one warp beam
change to the next, so trouble-free
production is guaranteed due to the
long-lasting effect and good adhesion
to the friction points.
QUIETSCH-EX is also an excellent
corrosion preventive and rust removal
agent.
Klüberpaste 46 MR 401 and
ALTEMP Q NB 50
also are universal lubricating and
assembly pastes preventing fretting
corrosion.
Recommended Lubricants Advantages Notes
22
10.0
Example Machine / Component Lubrication Problem / Requirements
Bearings of drying cylin-ders and calender rollersin sizing dryers
Gripper looms(tape gripper looms)
Open gears and chains
If mineral-oil-based lubricants are used, high bearingtemperatures (drying cylinders up to max. 165 °C)result in short lubrication intervals and/or increasedresidue formation.
Rolling bearings subject to vibrations, especially in theflywheel support and the crosshead axle
Motor coupling withbrake and sliding block
Rapier guide roller anddistributor cutter
Short oil change intervals in tape driveWeaving machine gears
Dragging motion
Tape grippers of gripper looms
High friction and wear as well as contamination of thewoven fabric by pasty and fluid lubricants
Dripping and splashing of the lubricant, short relubri-cation intervals and thus high maintenance require-ments and wear problems
Furthermore, contamination of the workplace and dis-turbing noise level due to insufficient damping orlubricating effect
Lubricants for Sizing Machines and Looms
23
SYNTHESO D 220Synthetic high-temperature oil.Suitable up to 150 °C and shortpeaks up to 180 °CFor grease lubrication:STABURAGS NBU 30 G 5(contains solid lubricant particles;e.g. for older types of sealing units)
STABURAGS NBU 12 (no solid particles; for cylinderbearings in the sizing section)
MICROLUBE GBU Y 131
or
STABURAGS NBU 12 ALTEMP
White special lubricant (containssolid lubricant particles) with a highpressure absorption capacity
GRAFLOSCON CA ULTRA-SPRAYAdhesive lubricant with graphite anda synergetic additive package sup-plied in a convenient aerosol can
HOTEMP 2000-SPRAYVery adhesive, high-performance oil,resistant to high temperatures, goodpenetration
SYNTHESO D 220 has excellent lubricating properties.
Compared with mineral oil, residueformation is substantially lower, and oilchange intervals can be extendedconsiderably (3 to 5 times longer).
SYNTHESO D 220 is recommendedfor sizing dryers. Calender manufac-turers recommend it for oil-lubricatedrolling and plain bearings subject tohigh thermal stress.
MICROLUBE GBU Y 131 allowsextension of relubrication intervals toone month, even at extremely highspeeds.
STABURAGS NBU 12 ALTEMP provides reliable protection againstfretting corrosion.
MICROLUBE GBU Y 131 has an
excellent backflow behaviour, which is
especially important in friction points
subject to oscillating motion.
This lubricant is recommended by
Sultex (Sulzer Textil).
Excellent wear protection combinedwith high adhesion allow extremelylong relubrication intervals.
Chain and gear lubricant, very adhe-sive, which prevents splashing, gooddamping properties. Suitable for sprayheads with point and wide-jet applica-tion
GRAFLOSCON CA ULTRA-SPRAY isan ideal lubricant for open gears. Well-metered application on drive chainsensures minimum adhesion of lint anddust.
HOTEMP 2000-SPRAY is a universalchain spray – also suitable for drive,control and transport chains runningat high speeds.
Recommended Lubricants Advantages Notes
SYNTHESO D 150 EP orSYNTHESO D 100 EP (dependingon weaving machine type) Fully synthetic gear oils with highpressure absorption capacity forextreme loads
Longer oil change intervals: approx.15000 op. hrs. instead of approx.5000 op. hrs. (mineral oil)
Recommended by VAMATEX for tapegripper and terry looms
For further information on gear lubri-cation see p. 30/31.
ISOFLEX TOPAS NB 52
ISOFLEX ALLTIME SL 1
Both ISOFLEX types are smooth-run-ning greases with operational reliabilityand long service life.
Recommended for weaving machinesby Sauer-Diederichs
ALTEMPAN POBWhite lubricant powder with extraordi-nary sliding characteristics; consump-tion approx. 1 g per 24 h per machine
This lubricating powder eliminates therisk of contamination and increasesthe service life of the gripper tapes byup to 100 %.
ALTEMPAN POB has been success-fully used for bobbins in bobbinetweaving for many years.
24
11.0
Example Machine / Component Lubrication Problem / Requirements
Rolling bearings in wash-ing and mercerisingmachines, dyeingmachines and festoonsteamers
Corrosion protection for the inner lining ofsteamers
Chains in steamers
Bearings in steamers
Bearing failures due to corrosion
Washing-out of the grease from the bearings bydetergents, processing fluids and splash water
Corrosion of steel lining resulting from severe mediaattack
Reduced production and increased costs for repair
Fabric conveyor chains
Condensates from softeners and finishing materials
Increased deposits at temperatures above 160 °C,resulting in dragging chain links, chain rattle and thusexcessive power consumption
Lubricants for Textile Finishing Machines
25
STABURAGS NBU 12 or 30STABURAGS NBU 12 / 300 KPWater and steam resistant specialgrease, which is also resistant toaqueous alkaline and aqueous acidsolutions
The lubricating grease has goodsealing properties and protectsbearings against corrosion.Alternatively: Klüberplex BE 31-222
STABURAGS NBU 30A hot-water, steam, alkali and acidresistant special grease, ideal for theinternal protection of steamers
High-temperature chain oils:Klübersynth CTH 2-260 orPRIMIUM FLUID SPECIAL orHOTEMP PLUS
UNISILKON L 50/2Alternatively: UNISILKON GLK 112
High operational reliability and resist-ance to water, hot water, aggressivevapours and many other mediaencountered in textile finishing
Good corrosion protection and longrelubrication intervals
STABURAGS NBU 12 or 30
STABURAGS NBU 12 / 300 KP
are special high-pressure and long-term greases for all lubrication pointsexposed to media.
STABURAGS NBU 30 is a reliable andeconomical long-term protection, as itprovides an internal coating which lastsfor one year or more in most cases.Premature expensive replacement ofthe steamer lining is, consequently, notnecessary.
Note: New steamer wall materials mayrequire a different long-term protectionagent.
STABURAGS NBU 30 is a speciallong-term grease with excellent seal-ing properties suitable for low-speedrolling and plain bearings in wet pro-cessing machines.
It is applied according to the recom-mendations of the machine manufac-turers.
Recommended Lubricants Advantages Notes
For sliding chains:Klübersynth CTH 2-260Fully synthetic high-performancechain oil for high temperatures orHOTEMP PLUSabove 200 °C orPRIMIUM FLUID SPECIAL
Grease lubrication for chains sup-ported by ball bearings:BARRIERTA L 55/2 for long-term lubrication or in acc.with manufacturer’s instructions. Long-term lubricated bearingshave a different design requiringlower relubrication quantities. Alternative for long-term lubrica-tion:Klübertemp HM 83-402UNISILKON L 50/2
For oil lubrication:HOTEMP PLUS
Separating effect on condensatesand, consequently, less build-up ofresidues. Efficient lubrication of thechain links, rolling bearings and sliderails under varying operating condi-tions (speed, temperature, stretchingtension). Low power consumptionwith practically wear-free operation
Synthetic sliding surfaces on stenterchains with special lubricant require-ments in terms of evaporation, forma-tion of residues, regenerative capacity,friction and wetting behaviour resultedin the development of KlübersynthCTH 2-260.
This special chain oil meets all require-ments and has a considerably betterviscosity-temperature behaviour thanprevious standard chains oils.
Klüber Lubrication high-temperaturechain oils for operating temperaturesup to 250 °C are recommended for alloil-lubricated chain systems in stenterframes, drying and setting machines,multi-layer systems, festoon steamers,steamers, condensers and coatinginstallations by leading machine manu-facturers.
26
11.0
Example Machine / Component Lubrication Problem / Requirements
Chains in dryers forprinted fabrics(in combination with the
printing machine)
Needle bars, clip tables
Rolling bearings in fansand exhaust fans in dryers(direct drive)
Deposits of condensates
Formation of residues at a temperature above 160 °C
Dragging chain links, chain rattle and excessive
power requirements
Contamination of the fabric by deposits of burnt-on
softeners and condensed finishing compounds
Extensive cleaning work
Rolling bearings of electric motors in dryers(indirect drive)
Cracking and carbon residues, as well as the loss of
grease due to high temperatures
Bearing wear and premature bearing failures
Increased maintenance and repair costs
Lubricants for Textile Finishing Machines
27
HOTEMP PLUS
Fully synthetic, high-performance,
high-temperature chain oil or
PRIMIUM FLUID SPECIAL
or
STRUCTOVIS BHDup to 120 °C
UNISILKON M 2000-SPRAY
or
UNISILKON TK 002/100for semi-automatic application via
drip feed oilers or rotating brushes
Separating effect on condensates
and, consequently, less build-up of
residues
Efficient lubrication of the chain links
at high operating temperatures
Low energy requirement of the
machine and virtually wear-free
operation
High-temperature chain oils produced
by Klüber Lubrication are recommend-
ed for all oil-lubricated chain systems
and fully meet the requirements of
chain and machine manufacturers and
operators.
Smooth opening and closing of clips
ensured by small lubricant quantities
(acting as release agent), which keeps
needle bars and clip tables clean
Regular application of the release
agent to low-speed clips or needle
bars ensures an optimum separatingeffect.
Expressly recommended by
MONFORTS
Recommended Lubricants Advantages Notes
STABURAGS N 12 MFHigh-temperature and long-term
grease with emergency lubricating
properties imparted by MoS2 solid
lubricant compound
or
according to the recommendation
of other manufacturers, e.g.
PETAMO GHY 133
UNIMOLY GB 2
MICROLUBE GNY 202
Klüberplex BEM 34-132< 150 ºC (Brückner)
Long relubrication intervals
Wear protection under boundary
friction conditions
Reliability at high operating tempera-
tures
STABURAGS N 12 MF for the lubrica-
tion of fan bearings. Exclusively rec-
ommended and time-tested for the
lifetime lubrication of electric motor
bearings
Also suitable for rolling bearings on
chain return wheels as well as grease
lubrication of splined shafts. The syn-
thetic lubricating greases
UNISILKON L 50/2
and
BARRIERTA L 55/2
offer sound technical and economical
solutions to applications with bearing
temperatures in excess of 150 °C,
especially for long-term and lifetime
lubrication.
28
11.0
Example Machine / Component Lubrication Problem / Requirements
Width adjustment spindles
Rolling and plain bearings in heated calenders
Compensator and guideroller bearings in Hotfluefinishing machines
Heavy build-up of contaminants with lubricating oils
or greases, as well as carbon and cracking residues
that may impede motion
In heated calenders the oil’s operating viscosity
is too low.
Mineral oils may cause the formation of residues, thus
short oil change intervals required.
Rotary couplings e.g. insteam-heated finishingmachines
Excessive seal wear due to inadequate lubrication of
the rolling bearings at temperatures up to 180 °C and
above
Relubrication intervals too short
Drying-out of the lubricating grease due to extreme
thermal influences
Lubricants for Textile Finishing Machines
29
MOLYBKOMBIN UMF T 4 – SPRAY
Molybdenum disulphide bonded
coating, providing a dry lubricating
film up to 450 °C
or according to manufacturer’s
special recommendation:
UNISILKON L 50/2
UNISILKON GLK 112
SYNTHESO D oils
Fully synthetic high-temperature
oils with good viscosity-tempera-
ture characteristics
Largely prevents the build-up of lint
and contamination. Consequently,
easy and accurate width adjustment is
possible requiring comparatively little
maintenance.
MOLYBKOMBIN UMF T 4 – SPRAY is
ideal in workshops for assembly pur-
poses, e.g. screwed connections and
bearing seats.
Protects against seizure, especially at
high temperatures.
Can be delivered through oil pumps
and pipe systems, also at room tem-
perature. At higher temperatures up to
150 °C or short peaks up to 180 °C
(maximum film temperature 225 °C)
SYNTHESO D oils have a higher oper-
ational viscosity than mineral oils of a
similar ISO viscosity grade and fulfil
the demands for the required full fluid-
film lubrication.
To suit the recommendations of
machine manufacturers SYNTHESO D
oils are available in all common ISO
viscosity grades.
ISO viscosity grades 220, 460 and
1000 are recommended.
Recommended Lubricants Advantages Notes
PETAMO GY 193
at temperatures up to 180 °C;
BARRIERTA L 55/2
or
Klübertemp HM 83-402
at temperatures above 180 °C;
Alternatively:
Klübersynth BH 72-422
Particularly good resistance to
aggressive media
High wear protection
Good sealing effect
Klübertemp HM 83-402,
PETAMO GY 193 and
BARRIERTA L 55/2
are expressly recommended by
Messrs. Maier Heidenheim.
STABURAGS NBU 30 G 5 is used in
older types of sealing units.
Klübertemp HM 83-402
or
BARRIERTA L 55/2
Synthetic high-temperature
lubricating greases
Alternatively:
Klübersynth BH 72-422
Very good resistance to aggressive
media and temperatures
Excellent lubricating properties
Klübertemp HM 83-402 and
BARRIERTA L 55/2
are also suitable for wear protection of
electrical contacts and suitable for the
lubrication of sliding material combi-
nations, i.e. plastic to plastic.
30
12.0
Example Machine / Component Lubrication Problem / Requirements
Spur and bevel gears
Rolling bearings in electric motors
High temperatures lead to rapid oil ageing and short
oil change intervals.
Extremely high specific flank pressure under mixed
friction conditions (e.g. with high torques at low
speeds)
Worm gears Excessive oil sump temperature
Rapid oil ageing and short oil change intervals
Excessive wear of wheel resulting in low efficiency
Premature bearing failure resulting in machine
downtime
Lubricants for Gear Units and Electric Motors in Textile Machines
31
Oil series:
Klübersynth EG 4 oils
High-performance gear oils on a
PAO basis
SYNTHESO D ... EP oils
Synthetic gear oils for extreme
loads on a PG basis
Other alternatives:
Klübersynth 100 KV(Klübersynth GE 4 75 W 90)Klübersynth G 4-130
(see Notes)
Good friction behaviour resulted in
gear temperature reduction by 10 °K
or more. Oil change intervals are at
least three times as long as those of
mineral oils.
Klübersynth EG 4 oils are available in
all common ISO viscosity grades.
They are miscible with mineral oil and
show mostly neutral behaviour
towards paints and seals.
SYNTHESO D ... EP oils are not misci-
ble with mineral oils or oils on a PAO
basis. We recommend testing com-
patibility with sealing materials, paints
and inspection glass.
The optimum choice for gear lubrica-
tion in weaving machines if long oil life
is desired. Approvals by several man-
ufacturers, e.g. by VAMATEX NUOVA
for Klübersynth 100 KV and by
SOMET for Klübersynth G 4-130
(for relubrication)
Recommended Lubricants Advantages Notes
Klübersynth GH 6 oils
High-performance gear oils on a
PG basis
Alternatively:
Klübersynth EG 4 oils
(see above)
or
STRUCTOVIS BHD MF
Klübersynth GH 6 oils have an excel-
lent friction behaviour. They reduce
gear temperatures considerably and
increase gear efficiency by more than
25 %. Owing to their special additives
they reduce wear substantially, espe-
cially on materials that are typically
used for worm gears. Oil change inter-
vals are at least five times longer than
those of mineral oils.
STRUCTOVIS BHD MF is an intrinsi-
cally viscous long-term and high-tem-
perature lubricant. It contains solid
lubricant particles and is especially
suitable for worm gear drives of width
adjustment spindles.
Klübersynth GH 6 oils are available in
all common ISO viscosity grades.
They are not miscible with mineral oils
or oils on a PAO basis. We recom-
mend testing compatibility with seal-
ing materials, paints and inspection
glass.
BRÜCKNER recommend
STRUCTOVIS BHD MF for the lubrica-
tion of worm gears in stenters.
Klüberquiet BQH 72-101, BQ 72-72for long-term and lifetime lubrica-
tion mostly of rolling bearings that
do not allow relubrication running
at > 100 °C and high speeds
For rolling bearings that can berelubricated:
Klüberplex BEM 41-132
Klüberquiet greases are characterized
by a wider service temperature range
and an extremely high resistance to
temperature and speed.
At high temperatures, runtimes
> 4000 hours are possible without
relubrication; the same applies to
Klüberplex BEM 41-132 at low tem-
peratures.
Klüberquiet/Klüberplex greases meet
most requirements to be satisfied by
today’s rolling bearing lubricants.
Our tried-and-tested greases
STABURAGS N 12 MF and
STABURAGS NBU 8 EP continue to
be good choices for many applica-
tions.
32
High-Pressure Stage
13.0
Example Machine / Component Lubrication Problem / Requirements
Screw-type compressor
Rotary vane compressor
High operating temperatures leading to rapid oil
ageing through oxidation, and short oil change
intervals
High operating temperatures leading to rapid oil
ageing through oxidation, and short oil change
intervals
Coking of the oil leads to formation of residues.
Cleaning of screw-typeand rotary vane com-pressors
(before)
(after)
Deposits due to pronounced oxidation especially of
mineral-oil-based products
This will inevitably lead to contamination of the new oil
fill unless the compressor is cleaned during
changeover.
Lubricants for Compressors in the Textile Industry
33
Klüber Summit SH oils
High-performance compressor oils
on a PAO basis
Klüber Summit DSL oils
High-performance compressor oils
on a diester basis
Clean compressor thanks to good
oxidation stability
Oil change intervals at least three
times longer than those of mineral oils
When changing over from mineral oils,
energy cost cuttings by 3 to 5% are
possible.
Klüber Summit SH oils are available in
all common viscosity grades. They are
miscible with any residual mineral oil in
the compressor and are mostly neutral
towards paints and seals.
Low tendency towards residue forma-
tion reduces deposits and gluing of
vanes.
Oil change intervals at least three
times as long as those of mineral oils
When changing over from mineral oils,
energy cost cuttings by 3 to 5% are
possible.
Klüber Summit DSL oils are available
in all common viscosity grades.
Compatibility with seals and paints
should be tested.
Recommended Lubricants Advantages Notes
Concentrated compressor
conditioner
Klüber Summit VARNASOLV
Concentrated conditioner for cleaning
screw-type and rotary vane compres-
sors, especially when changing over
from mineral-oil-based products to the
synthetic Klüber Summit DSL or SH oil
Klüber Summit VARNASOLV is added
to the oil fill at a concentration of 10 %
and should remain in the compressor
for 40 to 60 operating hours.
Then drain the compressor while the
oil is still hot.
When used at a concentration of
10 %, VARNASOLV is compatible with
all materials resistant to mineral oil.
The oil ageing condition can be visual-
ly inspected (preferably before oil
change) by means of the
Klüber Summit TAN kit.
34
14.0
Highly efficient lubricating oil on a mineral hydrocarbon basis for friction
gears
Synthetic high-temperature chain oil, retards wear, spreads easily and
adheres excellently
Very adhesive, fully synthetic high-temperature chain oil;
solvent: hydrocarbon; propellant: propane-butane
Instrument oil for a wide service temperature range
Needle and sinker oil for hosiery knitting machines with anticorrosive and
antiwear effect; dampens vibration and noise; for oil circulating systems
Special running-in oil with a synthetic ester basis for problem-free running-
in of knitting machines, especially at low ambient temperatures (new or
overhauled machines)
Special cleaning oil for stitch-forming elements in circular, flat-bed and
hosiery knitting machines; dissolves contaminants such as yarn dust, fibre
particles and paraffins during machine operation
Special cleaning oil for stitch-forming elements in circular, flat-bed and
hosiery knitting machines; dissolves contaminants such as softening
agents from synthetic fibres or unsuitable needle and sinker oils during
machine operation
High-performance needle and sinker oil for the knitting industry; based on
universal and synthetic oils; scourable with customary washing liquors
High-performance needle and sinker oil with a mineral oil basis; scourable
with customary washing liquors; compatible with elastane fibres
Synthetic compressor oil with excellent low-temperature behaviour; espe-
cially for application in screw-type compressors
Synthetic compressor oil with reduced deposit formation; preferred choice
for piston and rotary vane compressors
Synthetic high-performance gear oil with excellent load-bearing capacity
and viscosity-temperature behaviour for use in weaving machines
Synthetic high-performance gear oil without additives for use in weaving
machines; neutral towards nonferrous metals such as brass, bronze, copper
Synthetic long-term gear oil on a PAO basis with very high scuffing load
capacity (GL 5) for use in weaving machines
Fully synthetic high-temperature oil for oil-lubricated stenter chains; effi-
cient lubrication also at high operating temperatures; low evaporation
losses; spreads and penetrates easily, also when used on chains with plas-
tic sliders
Klüber products
FORMINOL DS 23 K
HOTEMP PLUS
HOTEMP 2000-SPRAY
ISOFLEX PDP 65
Klüber Madol 172Klüber Madol 183
Klüber Silvertex P 91
Klüber Silvertex R 14
Klüber Silvertex R 20
Klüber Silvertex T 22 / T 32 / T 46
Klüber Silvertex W 22 / W 32
Klüber Summit SH 32…100
Klüber Summit DSL 32…125
Klübersynth 100 KV
Klübersynth G 4-130
Klübersynth GE 4 75 W 90
Klübersynth CTH 2-260
Application notes
Product Overview14.1 Lubricating Oils
Please order further information on the a.m. products
35
Fully synthetic high-performance gear oils for cylindrical, bevel and worm
gears; they are miscible with mineral oils and almost neutral towards
commercial sealing materials and paints; these oils offer good wear and
corrosion protection, as well as resistance to ageing and oxidation; in the
FZG test (A 10/16,6R/90) they achieve the scuffing load stage GL 4.
High-performance gear oils on a polyglycol basis with a high scuffing load
stage and good protection against wear; in the stringent FZG test
A/16.6/140 they achieve a scuffing load stage > 12 and a work-related
change in weight < 0.2 mg/kWh; GH 6 oils are particularly resistant to age-
ing and oxidation, they have a good viscosity-temperature behaviour and
are especially suitable for high-temperature lubrication1) (up to 150 °C, oil
sump temperature > 100 °C). Developed for the lubrication of steel/bronze
worm gears, GH 6 oils are also suitable for the lubrication of all types of
spur and bevel gears; Klübersynth GH 6 oils are not miscible with mineral
or PAO oils; we recommend testing compatibility with sealing materials,
paints and inspection glass.
Traction fluid for infinitely variable frictional control gears made of soild
steel
Fully synthetic high-temperature chain oil
Thin-bodied universal fluid on a mineral hydrocarbon basis ensuring excel-
lent wetting and penetration; suitable as a lubricant, rust dissolving and
anticorrosion agent; free from solvents
Intrinsically viscous long-term and high-temperature lubricant on the basis
of mineral oil and synthetic hydrocarbon oil
Intrinsically viscous long-term and high-temperature lubricant on the basis
of mineral oil and synthetic hydrocarbon oil; contains solid lubricant parti-
cles (MoS2)
Synthetic high-temperature lubricating and heat transfer oil on a PAG
basis; not miscible with mineral and PAO oils; we recommend testing com-
patibility with sealing materials, paints and inspection glass.
High-performance gear oils for the lubrication of spur and bevel gears
operating under extreme loads; also suitable for hypoid gears; the oil of
ISO VG 220 passes the FZG-L-42 test (hypoid gear test); not miscible with
mineral and PAO oils; we recommend testing compatibility with sealing
materials, paints and inspection glass.
Mineral-oil-based antiwear needle and sinker oils; scourable with custom-
ary washing liquors
Klüber products
Klübersynth EG 4-150Klübersynth EG 4-220Klübersynth EG 4-320Klübersynth EG 4-460Klübersynth EG 4-680Klübersynth EG 4-1000
Klübersynth GH 6-32Klübersynth GH 6-80Klübersynth GH 6-100Klübersynth GH 6-150Klübersynth GH 6-220Klübersynth GH 6-320Klübersynth GH 6-460Klübersynth GH 6-680Klübersynth GH 6-1000
LAMORA VARIOGEAROIL EL 2
PRIMIUM FLUID SPECIAL
QUIETSCH-EX UNIVERSAL FLUID-SPRAY
STRUCTOVIS BHD
STRUCTOVIS BHD MF
SYNTHESO D 220
SYNTHESO D 100 EPSYNTHESO D 150 EPSYNTHESO D 220 EP
TEX SYNTHESO M 32 NTEX SYNTHESO M 46 N
Application notes
1) see page 39Please order further information on the a.m. products
36
Klüber products
Klüberoil TEX 1-22 NKlüberoil TEX 1-32 NKlüberoil TEX 1-46 N
Klüber Summit VARNASOLV
UNISILKON M 2000-SPRAY
UNISILKON TK 002 / 100
UNISILKON TK 017 / 200 THERM (as example)
BARRIERTA L 55 /2
GRAFLOSCON CA ULTRA-SPRAY
ISOFLEX ALLTIME SL 1
ISOFLEX LDS 18 SPECIAL A
ISOFLEX NBU 15
ISOFLEX NCA 15
ISOFLEX SUPER LDS 18 / 25 S
Application notes
14.2 Release agents
Please order further information on the a.m. products
Anti-wear and biodegradable needle and sinker oils; good scourability with
commercial washing liquors, protect against corrosion, dampen oscillation
and noise, compatible with elastane fibers
Concentrated compressor conditioner; reliably dissolves varnish and
carbon build-ups during operation
Clear silicone film, free from solvents; suitable as a release agent to prevent
softening or finishing agents from sticking to needle bars and clip tables
Colourless, clear synthetic oil on a methyl silicone oil basis; suitable as a
release agent to prevent softening or finishing agents from sticking to
needle bars and clip tables
Lubricating oil on a methyl phenyl silicone oil basis with an excellent resist-
ance to high temperatures; no polymerization after 1000 h at 250 °C1)
High-temperature lubricating grease, resistant to water, extremely resistant
to oxidation, not aggressive towards most elastomers and plastics, not
corrosive towards ferrous and nonferrous metals, resistant to most chemi-
cals and organic solvents (also to CHC solvents); not resistant to
fluorinated hydrocarbon solvents
Adhesive spray lubricant with a high solid lubricant content (fine graphite),
CFC-free, contains solvent; suitable for small open spur and bevel gear
stages and for the external lubrication of chains; good absorption of high
pressure, good anticorrosion properties; thermal load carrying capacity,
depending on relubrication, up to approx. 200 °C1)
Dynamically light rolling bearing grease for high speeds and a wide service
temperature range
Dynamically light grease for plain and rolling bearings subject to high
speeds; good pressure absorption capacity
Lubricating grease for plain and rolling bearings subject to high speeds;
good pressure absorption capacity
Lubricating grease for plain and rolling bearings, especially for spindle and
taper roller bearings subject to very high speeds
Dynamically light grease for plain and rolling bearing subject to high
speeds; dispersed in a solvent (aliphatic hydrocarbon) for easier
application
14.3 Lubricating greases
1) see page 39
37
Sliding grease for friction points in textile machines and optical equipment
Plain and rolling bearing grease for a wide service temperature range,
excellent resistance to water, good pressure absorption capacity
Fully synthetic lubricating grease manufactured under clean-room condi-
tions, hence very high purity and low noise; for use at up to 180 °C1)
Lubricating grease forming a lubricating film of high mechano-dynamical load resi-
stance; very good wear protection and resistance to aggressive media; sealing effect
Special grease offering high resistance to water and aggressive media
Special grease offering good high-temperature resistance1) (up to 150 °C)
as well as wear and corrosion protection
High-performance grease for lubrication of carriage guides and the bases
of needle and selection slides
Long-term and high-temperature grease for slow moving rolling bearings,
plain bearings and slideways; operating temperature1) up to 220 °C; friction
points can be cleaned with organic solvents
High-temperature and long-term grease with a fully synthetic basis; neutral
towards a large number of plastic materials, especially FKM; high resist-
ance to chemicals and aggressive media
Low-noise rolling bearing grease for long-term lubrication; very good com-
patibility with elastomers and excellent low-temperature behaviour
Long-term grease for plain and rolling bearings to prevent tribocorrosion;
suitable for high temperatures, very adhesive, resistant to oxidation, pro-
longed working and water; excellent pressure absorption capacity and
good protection against corrosion
High-temperature grease for plain and rolling bearings
Long-term and high-temperature grease for rolling bearings in electric
motors, high-temperature fans, driers, textile machinery
High-temperature grease for rolling bearings
High-temperature grease with synthetic base oil for plain and rolling bea-
rings; good pressure absorption capacity
Smooth-running grease for long-term lubrication e.g. of belt guiding rollers
High-temperature long-term or lifetime grease for encased rolling bearings
that are not relubricated, especially for electric motors; good emergency
lubrication properties owing to the MoS2 solid lubricant combination
Long-term grease for plain and rolling bearings; suitable for high tempera-
tures, resistant to hot water, good pressure absorption capacity
Klüber products
ISOFLEX TEL 3000 ALTEMP
ISOFLEX TOPAS NB 52
Klüberquiet BQH 72-102
Klüberplex BE 31-222
Klüberplex BEM 34-132
Klüberplex BEM 41-132
Klüber Silvertex GREASE 3000 N
Klübersynth BH 72-422
Klübertemp HM 83-402
Klüberquiet BQ 72-72
MICROLUBE GBU Y 131
MICROLUBE GNY 202
PETAMO GHY 133 N
PETAMO GY 193
PETAMO GHY 441
STABURAGS N 4
STABURAGS N 12 MF
STABURAGS NBU 12
Application notes
Please order further information on the a.m. products 1) see page 39
38
Lubricating grease for plain and rolling bearings, especially for lubrication
points subject to external vibrations or oscillations
Long-term grease for plain and rolling bearings; suitable for high tempera-
tures, resistant to hot water, good pressure absorption capacity
Adhesive grease, resistant to steam, good pressure absorption capacity;
suitable as a valve and sealing grease for plain and rolling bearings operat-
ing at low speeds
Adhesive grease, resistant to steam, good pressure absorption capacity;
suitable as a valve and sealing grease for plain and rolling bearings operat-
ing at low speeds
Fluid grease with a wide service temperature range; especially suitable for
splash lubrication of steel/bronze worm gears; universally suitable for long-
term and lifetime lubrication
Valve and bearing grease for hot water valves and rubber seals, e.g. in
autoclaves and HT dyeing installations; resistant to water and oxidation;
protects against corrosion
Emulsifiable and scourable grease for ring travellers
High-temperature grease for rolling bearings; especially suitable for electric
motors, fans, chain wheel bearings
Silicone grease for a service temperature range1) between – 50 °C and
180°C; good wetting of surfaces
Lubricating grease for plain and rolling bearings with a wide service tem-
perature range; protects against seizure at high temperatures
Rolling bearing grease containing solid lubricant particles; suitable for
increased loads and for emergency lubrication in case of surface pressure
or sliding friction
Klüber products
STABURAGS NBU 12 ALTEMP
STABURAGS NBU 12 / 300 KP
STABURAGS NBU 30
STABURAGS NBU 30 G 5
STRUCTOVIS P LIQUID
SYNTHESO PROBA 270
TEX SYNTHESOTRAVEL 45WEISS A
UNIMOLY GB 2
UNISILKON GLK 112
UNISILKON L 50 / 2
UNISILKON TK 44 N 2 REC A
Application notes
Please order further information on the a.m. products 1) see page 39
39
1) Service temperatures are guide values which depend on the lubricant’s composition, the intended use and the application method. Lubricantschange their consistency, apparent dynamic viscosity or viscosity depending on the mechano-dynamical loads, time, pressure and temperature.These changes in product characteristics may affect the function of a component.
The data in this technical brochure is based on our general experience and knowledge at the time of printingand is intended to give information of possible applications to a reader with technical experience. It consti-tutes neither an assurance of product properties nor does it release the user from the obligation of per-forming preliminary tests with the selected product. We recommend contacting our Technical Consult-ing Staff to discuss your specific application. If required and possible we will be pleased to provide asample for testing. Klüber products are continually improved. Therefore, Klüber Lubrication reservesthe right to change all the technical data in this technical brochure at any time without notice.
Publisher and design: Klüber Lubrication München KG
Copyright: Klüber Lubrication München KG
5.49 e, edition 07.03
replaces edition 04.99
Reprints, total or in part, are permitted if source is indicated
and a voucher copy is forwarded.
Light-coloured multi-purpose and assembly paste reducing stick slip and
fretting corrosion
“White” multi-purpose paste with a very high pressure absorption capacity;
prevents tribocorrosion and protects against corrosion
Assembly paste on a synthetic oil basis; free from heavy metals and halo-
gen; service temperature range1) – 40 °C to 1000 °C; above 200 °C dry
lubrication, below 200 °C excellent corrosion protection
Multi-purpose and assembly paste, e.g. for the initial lubrication of sliding
points and joints after maintenance
High-temperature compound, release and sliding agent for screws, guide-
ways, gates and low-speed plain bearings
Klüber products
ALTEMP Q NB 50
Klüberpaste 46 MR 401
Klüberpaste HEL 46-450
UNIMOLY PLUS
WOLFRACOAT C
White lubricating powder for weaving machines
Solid lubricant suspension in mineral oil supplied as a spray; solvent:
hydrocarbon; propellant: propane-butane
Solid lubricant with binding agent for spray lubrication of threaded spindles
in stenters; solvent: acetone; propellant: dimethyl ether
ALTEMPAN POB
MOLYBKOMBIN M 5-SPRAY
MOLYBKOMBIN UMF T 4-SPRAY
Application notes
14.4 Lubricating pastes
Please order further information on the a.m. products.
14.5 Solid lubricants
Klüber Lubrication München KGGeisenhausenerstraße 781379 MünchenGermany� +49 89 7876-0Telefax +49 89 [email protected]
Klüber Lubrication AustriaGes.m.b.H.Franz-Wolfram-Scherer-Straße 32Postfach 845028 Salzburg-KasernAustria� +43 662 452705-0Telefax +43 662 [email protected]
Klüber Lubrication BeneluxS.A./N.V.Rue Cardinal Mercier 1007711 DottigniesBelgium� +32 56 483311Telefax +32 56 [email protected]
Klüber Lubrication CZ s.r.o.Prazakova 1061900 BrnoCzech Republic� +420 5 43424836-7Telefax +420 5 [email protected]
Klüber Lubrication Skandinavien A/SLiterbuen 92740 SkovlundeDenmark� +45 70 234277Telefax +45 70 [email protected]
Klüber Lubrication SkandinavienA/S, Filial FinlandMartinkyläntie 6701720 VantaaFinland� +358 9 8545610Telefax +358 9 [email protected]
Klüber Lubrication France S.A.S.Z.I. des Auréats,10 à 16 Allée E. Ducretet26014 Valence CedexFrance� +33 4 75448436Telefax +33 4 [email protected]
Klüber Lubrication Italia S.a.S.Via Monferrato 57, Sesto Ulteriano20098 S. Giuliano MilaneseCasella postale 438120098 San Giuliano Milanese Centro (MI)Italy� +39 02 98213-1 Telefax +39 02 98281595 [email protected]
Klüber Lubrication Benelux N.V.Energiestraat 51411 AN NaardenPostbus 1111400 AC BussumNetherlands� +31 35 6951464Telefax +31 35 [email protected]
Klüber Lubrication SkandinavienA/S, Filial NorgePostboks 721483 SkyttaNorway� +47 67067840Telefax +47 [email protected]
Klüber Lubrication Polskasp.z o.o.ul. Skoczowska 1961-345 PoznanPoland� +48 61 8700790Telefax +48 61 [email protected]
Klüber Lubrication GmbH Ibérica S. en C.Carretera C-17, Km 15,508150 Parets del Vallés (Barcelona)Spain� +34 93 5738400,Telefax +34 93 [email protected]
Klüber Lubrication SkandinavienA/S, Filial SverigeBox 601194 26 Upplands VäsbySweden� +46 8 59098600Telefax +46 8 [email protected]
Klüber Lubrication AG (Schweiz)Thurgauerstrasse 398050 ZürichSwitzerland� +41 1 3086969Telefax +41 1 [email protected]
Klüber LubricationYaglama ÜrünleriSanayi Ve Ticaret A.S.Cerkezköy Organize Sanayi BölgesiAtatürk Cad. 10 Sok. No: 7Cerkezköy/TekirdagTurkey� +90 282 7581530Telefax +90 282 [email protected]
Klüber Lubrication Great Britain Ltd.Hough MillsNorthowram, Halifax, HX3 7BNGreat Britain� +44 1422 205115Telefax +44 1422 [email protected]
Klüber Lubrication Argentina S.A.Martin J. Haedo 4301/63(1602) FloridaProv. Buenos AiresArgentina� +54 11 4709-1400Telefax +54 11 [email protected]
Klüber LubricationLubrificantes Especiais Ltda. & Cia.Rua São Paulo, 345Distrito Industrial de Alphaville06465-902 Barueri - São PauloBrazil� +55 11 4166-9000Telefax +55 11 4195-6832, [email protected]
Klüber Lubrication North America L.P.North American Headquarters32 Industrial DriveLondonderry, NH 03053USA� +1 603 647-4104Telefax +1 603 [email protected]
Klüber Lubrication North America L.P.Canadian officeOntarioCanada� +1 905 3049485Telefax +1 905 [email protected]
Klüber Lubrication TexasSummit Industrial Products, Inc.9010 County Road 2120Tyler, Texas 75707POB 131359Tyler, Texas 75713USA� +1 903 5348021Telefax +1 903 [email protected]
Klüber Lubrication Chile Ltda.Avda. Pdte. Eduardo Frei M. 9950oficina Nº 5, Cargo ParkQuilicura, Santiago Chile� +56 2 7471188Telefax +56 2 [email protected]
Klüber Lubricación Mexicana, S. A. de C. V.Boleo 62, Col. Maza, Del.Cuauhtemoc06270 Mexico, D.F.Mexico� +52 55 57020048Telefax +52 55 [email protected]
Klüber Lubrication China Ltd.Hong Kong OfficeUnit 18, 1/F., AdvancedTechnology CentreNo. 2, Choi Fat StreetSheung Shui, New TerritoriesHong KongChina� +852 26920191Telefax +852 [email protected]
Klüber Lubrication China Ltd.Beijing Representative OfficeRoom 610, Junefield PlazaNo. 6 Xuanwumenwai StreetXuanwu District, BeijingChinaPost Code: 100052� +8610 6310-3568, 6310-3569,6310-4504Telefax +8610 [email protected]
Klüber Lubrication China Ltd.Shenzhen Representative OfficeRM 2903, Huaneng BuildingShennanzhong RoadFutian District, Shenzhen CityChinaPostal Code: 518031� +86 755 8368-0482Telefax +86 755 [email protected]
Klüber Lubrication (Shanghai) Co. Ltd.Shanghai Liaison OfficeRm 2504, World Trade TowerNo.500 Guang Dong RoadShanghaiChina Postal Code: 200001� +86 21 63620160Telefax +86 21 [email protected]
Klüber Lubrication (Shanghai) Co. Ltd.Chengdu Liaison OfficeNew Times Plaza, 17 CWenwu Road, No. 42, Xinhua StreetChengdu, SichuanChinaPostal Code: 610017� +86 28 8675-2970, +86 28 8675-2971Telefax +86 28 [email protected]
Klüber Lubrication India Pvt. Ltd.504, A-Wing, Navbharat EstatesZakaria Bunder RoadSewri (West), Mumbai – 400 015India� +91 22 24178580,+91 22 24178740Telefax +91 22 [email protected]
NOK Klüber Co. Ltd.5th Floor Seidensha Bldg.1-10-11, Hamamatsu-ChoMinato-Ku, Tokyo, 105-0032Japan� +81 3 3434-1734Telefax +81 3 [email protected]
NOK Klüber Co. Ltd.Kitaibaraki Plant955-4, Aza - Ohishi, IsoharaIsoharamachi, Kitaibaraki-City Ibaraki – 319-15Japan� +81 293 427320, 425365Telefax +81 293 [email protected]
Klüber Lubrication Korea Ltd.Seoul Head OfficeSuite 802, Samhwan Camus Bldg. 17-3Yoido-Dong, Youngdungpo- kuSeoulKorea� +82 2 7825151Telefax +82 2 [email protected]
Klüber Lubrication Korea Ltd.Factory562 Okmyung-ri Daesong-myunNam-ku, Pohang, Gyungbuk 790-840Korea� +82 54 278-5151Telefax +82 54 [email protected]
Klüber Lubrication (Malaysia) Sdn. Bhd.No. 17 Jalan PJU 3/49Sunway Damansara Technology Park47810 Petaling JayaSelangor Darul EhsanMalaysia� +60 3 78034954Telefax +60 3 [email protected]
Klüber Lubrication South East Asia Pte. Ltd.25 International Business Park# 04-54 German CentreSingapore 609916� +65 65 629460Telefax +65 65 [email protected]
Klüber Lubrication (Pty) Ltd.P.O. Box 11461Randhart, Alberton 1457South Africa� +27 11 908-2457, -2458, -2459Telefax +27 11 [email protected]
Klüber Lubrication Australia Pty. Ltd.1st Floor, 3 Brand DriveP.O. Box 4Thomastown, VIC. 3074Australia� +61 3 94647577Telefax +61 3 [email protected]
Klüber Lubrication Australia Pty. Ltd.Sydney OfficeUnit 23, 380 Marion Street Condell Park, NSW 2200, Sydney Australia� +61 2 97908562Telefax +61 2 [email protected]
www.klueber.comKlüber Lubrication München KG a member of the Freudenberg group