SPECIFICATION OF EQUIPMENTS (No.1 to 40 - AS PER LIST)

1.SPECIFICATION FOR LEAD APRON

1. Lead Apron with collar2. Coat type Made of lead vinyal3. Length – 100 cm and width 60cm4. Velcro type5. Lead thickness – 0.35 or 0.5 Pb6. BARC/CE certified

2.SPECIFICATION FOR PLASTER DISPENSER

Outside & inside body is made of stainless steel. Operating both manually/ press on switch. Timing can be adjusted from 1sec to 100 sec. Capacity 10 Kg.

3

DOUBLE DISC MODEL TRIMMER

Specifications 1. Heavy duty double motors (2500-3000 rpm 1 Hp each) with two ball

bearings each motor2. 10 inch course carborandum cutting stone and 10 inch fine diamond/ indian

polishing stone disc3. Single speed and continuous rating4. Power supply 230 v 600 w 50/60 HZ

5. Wt 15-20 kg6. Inlet/outlet with PVC pipe 7. Installation by supplier

4.SPECIFICATION FOR HEAVY DUTY LATHE

Single motor 1 HP 2800 RPM heavy duty equipped with two ball bearing single speedcontinuous rating with 3 chucks (buffer, stone, bur chuck) high speed.

5.SPECIFICATION FOR ULTRA SONIC CLEANER 5

LIT.

Timer : YesConstruction : Stainless SteelFrequency Output : 60 kHzHeater : OptionalCapacity : 5 litre

6.

Specification for Spindle Alloy Grinder

Dental High Speed Spindle Alloy Grinder HP-1, RPM 2800

Heavy Duty, Equipped with two ball bearing single speed with high speed Spindle RPM-24000 with suction.ISO Certified

7.

PIN DEX SYSTEM

8.VACCUM MIXER

9.

SPECIFICATION FOR CIRCULAR SAW

Dental High Speed Spindle Alloy Grinder HP-1, RPM 2800

Heavy Duty, Equipped with two ball bearing single speed with high speed Spindle RPM-24000 with suction.ISO Certified

10.

Specification Bleaching Unit

Model NO.: M209A Medical Device Regulatory Type: Type 2 Input Voltage : AC100-240V Power: 33W to 40 W Illumination Density: 200-300mW/Cm2 Amount of LED tube - 8pcs Dimension of appearance (LxWxH) – 150x60x123cm. Product Size: 82 x 28 x 112cm Gross Weight: 10kg Type: Bleaching, Cleaning & Filling Teeth Equipments Light Source: LED Blue Light Output Wavelength: 460-490nm Light Bulb: 6

11.PNEUMATIC CHISEL

12.

Specification for Lab Air Rotor

RPM Range : 1,000-50,000 RPM

Torque : 8.7 Ncm

All-in one turbine, air nozzle and spray, reduced weight and ergonomic design, whisper quiet/no vibration, high torque, fiber optics and smooth transitioning while increasing or decreasing rpm’s. When choosing a dental laboratory hand piece and motor , Lightweight

13.

Specification for Vibrator

Big platform size adequate at least two bowls Noiseless smooth uniformly vibrating

14 .Specification for Rubber Dam Kit

Should be supplied with Rubber dam sheets (5/5), 12 clamps –anterior and posterior, Plastic and metallic frames, Rubber dam punch, Rubber dam template, Dental floss Clam forcep

15.

Specification for Impaction KitShould include Forceps- Maxillary set of 7 and mandible-set of 6Retractors 2 each (Austin, Langenback (small, & medium)Periosteal elevators 2 each (Molts and Howarth)Elevators I each- {straight & Copuland,

16Specification for Surgical Kit

Should includeB P Handles- 3 No.Toothed tissue forceps- 2 No.Non –Toothed tissue forceps- 2 No. Small artery forceps (straight) - 2 No.Small artery forceps (curved) - 2 NoNeedle holder-2 NoSuture cutting scissors (micro scissors)- 2 NoWire twister-1 NoWire cutter- 1 NoTissue dissectors/scissors - 2 No

17.

Specification for Physiodispensor Hand PieceContra angle hand piece with hexagon clamping system, 20:1 reduction ratio and light

18.

Specification for Intra Oral Camara with Monitor

Images - CCDVideo Output: High Speed USD 2.0Focus Range – 5-45 mmFocus Type – Fixed Cable Length- 5 m

Weight- 45gFeatures- Integrated frame, capture button, chair/ table mounted holder with on/off capability

19.

Specification for U.V.Chember Chamber Size 23”x12”x8” UV tube – 15 watt with duble tube Number of trays – 12 Door closing Mechanism –Magnetic Gasket

High quality stainless steel Equipped with Philip &

Osram UV tube

20

SPECIFICATION FOR GRASEBY TM 2100 SYRINGE PUMP

1. Factory calibrated for international & local brands of syringes including Rumson’s junior & unlock ( dispovan) so users can select and change syringe brands at the bedside without sending it to the biomedical department forcalibration

2. On pump syringe loading guidelines makes easy to use for the user 3. LED screen gives better visibility from far compared to LCD screen4. Front loading syringe where syringe driver arm is protected by syringe pump

body 5. Different button for turning on syringe pump and starting infusion thus avoiding

any error6. Safety features such as : a. patient tubing holder b. Post occlusion bolus

reduction c. key pad to be locked while infusion is on 7. Body weight mode help in calculating flow rate as prescribed by the physician

instead of manua

21.

DRY MODEL TRIMMERSpecifications

1. Should be Waterless,2. Speed 1400- 3000 rpm, heavy duty motor with ball bearings3. Long life diamond coated disc, fine4. Electric socket for automatic connection to the extraction system,5. Power supply 230 v 600 w 50/60 HZ6. Wt 15-20 kg7. With extra corborandum fine disc- 1nos

22.

Specification for Polishing Lathe

Dental Lathe Model, HP-1, Universal, RPM-2800Equiped with Double B.B, Single speed Rating continuous with chucks (Buffer,Stone & Bur Chuck)

23.

Specification for Light Curing Unit (LED)It should have optical fiber rotatable & autoclavable, much longer standby time, having three modes, battery can be replacable, battery should be of 3.7 v.having optical fiber black in colour.

24

Specification for Blow TorchIt should have on off button. It should have a nob to control gas.

25.

Specification for Airotor Handpiece with spare cartridge

Stainless steel slim body, super torque, low noise & vibration , 350,000 to 4,50,000 rpm speed, sterilizable up to 135C, push button technology, ceramic bearings,

26.

Specification for Endomotor

Hand piece with integrated on/off switch (only 3.22ounces or 92 gms)Large LCD screen, Speed range 120 rpm to 800 rpm, Auto reversefunction, Torque control range 0.6 to 5.2 Ncm, 9 adjustable programme selection With a supplied 16:1 compact contra angle, Operates on battery or electrical power

27.

Specification for Extraction forceps kitRust- free, light weight premium quality forceps which includes following1) lower anterior forcep2) lower premolar forcep3) lower molars & wisdom forcep right 4) lower molars & wisdom forcep left

5) lower third molars6) lower root forcep7) upper anterior forcep8) upper premolar forcep9) upper molars right10) upper molars left11) upper root forcep12) upper third molar forcep13) lower cow horn molar forcep14) upper cow horn molar (right) forcep15) upper cow horn molar (left) forcep

28.

Specification for Extraction elevator kit

1 ) hospital pattern straight elevator

2) cryer elevator right

3) cryer elevator left

4) Apex elevator right

5) apex elevator right

6) Winter cryer elevator right

7) Winter cryer elevator left

8) warwick james elevator straight

9) warwick james elevator right

10) warwick james elevator left

29.

BURNOUT FURNACE SPECIFICATIONS

1. Quick heating burnout furnace with heavy duty ceramic fibre blanket insulation, kanthal wire heating element with insulation,

2. Silver thermal fuse with two meter power lead 220-250 volts3. Maximum temp 1200-1300oc4. Working temp 11500c

a. Digital display and digital controller

30.

Indirect Sinus lift Kit i.e Crestal approach sinus Kit (CAS)Specifications

1. Should have CAS drill ranging from diameter 2.8 to 4.1mm2. Hydraulic Membrane Lifter easy to use to lift the sinus membrane3. Unique stopper system that prevents over drilling into the sinus cavity4. Should have ability to combine ostetome surgery5. Should have bone carrier system for transferring and filling bone material at surgical site6. Should have bone spreading for spreading bone material7. Should be simple for surgical system8. Should have colour coding for stoppers, 9. Should have depth guage10. Should have Guide drill and twist drill

31.

DOUBLE DISC MODEL TRIMMER

Specifications

1. Heavy duty double motors (2500-3000 rpm 1 Hp each) with two ball bearings each motor

2. 10 inch course carborandum cutting stone and 10 inch fine diamond/ indian polishing stone disc

3. Single speed and continuous rating4. Power supply 230 v 600 w 50/60 HZ5. Wt 15-20 kg6. Inlet/outlet with PVC pipe 7. Installation by supplier

32.

Specifications Osteotome Kit for sinus lift surgeries 1. Instruments with Concave tip designs ranging from 2-4mm which direct

compressive force to the bone.2. It should effectively and safely elevate the sinus membrane3. It should have the stopper system for safe and control penetration4. It should have lazer marking length guide5. It should have separate mallet for efficitive crestal bone tapping6. It should length indicator from range 5-15mm7. It should have offset body design so as to easily and correctly position an

osteotome

33.

Specification: - Lab Micromotor with Heavy duty Hand piece

Light weight well balanced construction for maximum hand

comfort has MINIMUM 6NCM torque and delivered speed up to

50000 RPM no oil lubrication required has both forward & reverse

direction working.

34.

Specifications: - Pneumatic Crown Remover

1 . Easy pneumatic crown and bridge remover II2. Bridge remover tip-#13. Single crown remover tip-#24. Single crown remover contrangled tip-#35. Open-end adjustment wrench 6. Rubber gasket7. Flexi-wire set 8. Storage/canying case 9. Instructional/clinical video(CD

35.

SPECIFICATIONS : DLP

Light ValveSingle chip DLP® LVDS(Low-voltage differential signaling) technology

Image Chipset 0.65" 1080p S600 DMD, DarkChip3™

Color Processing Technology BrilliantColor™

ANSI Lumens (Max>) 3,000 ANSI Lumens (Max.)

Contrast Ratio

2000:1 Typical (Full On/Full Off)

Uniformity 75% Typical (Japan Standard - JBMA)

Aspect Ratio 16:9

Native Resolution 1920 x 1080 (1080p)

Vertical Keystone Correction Manual +40° / -40°

Video CompatibilityComposite Video input:NTSC: M (3.58 MHz), 4.43 MHzPAL: B, D, G, H, I, M, N, 4.43 MHzSECAM: B, D, G, K, K1, L, 4.25/4.4 MHzComponent Video via VGA input:1080i (50/60Hz), 720p (50/60 Hz), 576i/p, 480i/pHDMI input:1080p, 720p, 576i/p, 480i/p

Lamp Type PHILIPS 220 W user-replaceable lamp

Lamp Life Up to 3,500 hours Normal ModeUp to 5,000 hours Eco-Mode

Projector Lens F-Stop: F/2.5~2.67Focal length, f=21.9-24 mm

Lens Offset Ratio 116 ± 5%

Throw Ratio 1.48~1.62 wide and tele

Zoom Manual 1.1X

Screen Size - Diagonal 84.98 cm ~ 774.7 cm (33.46" ~ 305") (diagonal)

Projection Distance

3.94 ~ 32.81 ft (1.2 ~ 10 m)

3D-Capable Active 3D goggles with DLP Link, 3D player software application, HDMI/VGA cable, 3D content, PC/laptop with a 120Hz signal output quad buffered graphics card are required and sold separately.

Mounting Capability with the exception of the Dell S520, all mounting kits are sold separately.

Ceiling-mountCeiling mount screw hole M3 x 6.5 mm depth.Recommended torque < 15 kgf-cm.

Projection Mode Front Projection - Desktop (Default) Rear Projection - Desktop Front Projection - Ceiling Mount Rear Projection - Ceiling Mount

Connectivity

Power AC power input socket (3-pin - C14 inlet)

Computer-In 1 x 15-pin D-sub connector (Blue),VGA In, for analog RGB/Component input signals

Computer-Out 1 x 15-pin D-sub connector (Black) for VGA-A loop through

Video-In 1x Yellow RCA jack for CVBS signal (Composite Video)

USB 1x mini USB-B slave for remote support and firmware upgrade

Audio Input Analog: 1x 3.5mm stereo mini phone jack (Blue)

Audio Output Variable: 1x 3.5mm stereo mini phone jack (Green)

HDMI Input 1 x HDMI connectors for supporting HDMI 1.4a. specification HDCP compliant.

5V/1A output: 1x USB type A 5V DC / 1 A output for support wireless display dongle.

Security

Kensington Lock SlotYes

Password Protection Yes

Quick Shutdown Yes (approximately 10 seconds)(prior set-up required)

Accessories

Remote Control Included with projector-Basic Infra Red (includes 2x AAA battery)

• with page-up/down 2

• w/o laser pointer

Remote Control Dimensions (WxDxH) 149mm x 52mm x 28mm ± 0.5mm(5.87" x 2.05" x 1.10" ± 0.02")

Remote Control Weight 65 g (0.6 lbs)

Ceiling Mount

Carrying Case

Dimensions

Dimensions (with stand)

Weight 2.8 kg (6.2 lbs)

Dimension (WxHxD) 314.4 mm x 86.7 mm x 223.5 mm(12.38" x 3.45" x 8.8")

Power

Power Supply Universal AC 100-240 V 50-60 Hz with PFC

Power consumption Normal Mode:275 W ± 10% @ 110 VacEco-Mode: 215 W ± 10% @ 110 VacStandby Mode: < 0.5 W

Noise Output Normal Mode: 35 dB(A) TypicalEco-Mode: 32 dB(A) Typical

Multimedia Audio 1x 10W speaker RMS

Elevator feet / Adjustment wheels 1x front tilt adjustment wheel (angle of tilt: -5° ~ 5°)2x rear tilt adjustment wheel

Should Include:

1x Dell 1850 Projector c/w lamp1x Power cord (DAO - 9.8ft, ROW - 1.8m) 1x VGA cable (1.8m / 5.9ft)1x Remote control2x AAA battery (remote control)CD User's Guide & Documentation

36.Specifications for Indirect Sinus lift Implant Kit

1. ∅2.0 Twist Drill The drill tip is 0.6mm and is 13mm long.

2. CAS-Drill its design forms conical bone and bone chips. - The CAS-Drill tip has an inverse conical shape

3. Comes in six diameters:∅2.8 / ∅3.1 / ∅3.3 / ∅3.6 / ∅3.8 / ∅4.1Unique Stopper system

4. Depth Gauge5. Hydraulic Lifter

The Hydraulic Lifter uses normal saline to raise the membrane6. Bone Carrier7. Bone Condenser8. Bone Spreader

9. Hydraulic Lifter Tube

37.

Ridge expansion Implant kit

1. Crest remover2. Twist Drill – Diameter 1.8

Length 8.5, 10,113. Saw (Blade Thickness 0.3 , Diameter 7,10,13 mm)4. Set drill For splitting and expansion of crest bone5. Mount Extension 6. Torque Wrench

Depth Gauge

38.Specification for Suction Machine

Vaccum pump :Twin Head , oil free Diaphragm PumpOperating Voltage : 230 Volt A.C. + 5%Jars for Collection : 2x 2 Liters Polycarbonate Shatterproof ( with flat valve)Remote Operation : Foot switch provided to unit selectively½ HP Motor

39.Specification for Orthodontic Plier set (set of 33 plier)

Orthodontic plier set (set of 33 plier - DISTAL END CUTTER, HARD WIRECUTTER, LIGATURE CUTTER STRAIGHT, BIRD BEAK PLIER WITH SERRATIONS,DELA ROSA WITH GROOVES, TWEEDS LOOP FORMING PLIER, OMEGAFORMING PLIER, RIBBON ARCH PLIER, DEBONDING PLIER CURVED,DEBONDING PLIER STRAIGHT, BAND CUTTING SCISSOR CURVED, BANDREMOVER, HOW PLIERSTRAIGHT, HOW PLIER CURVED, BAND PUSHER,SEPERATOR PLACING PLIER, WEINGART PLIER, MATHEWS NEEDLE HOLDER,MINI NEEDLE HOLDER STRAIGHT, HOOK CRIMPING PLIER, TORQUING PLIERFEMALE, TORQUING PLIER MALE, BRACKET PLACING PLIER, LIGATURETUCKER, ARCH FORMING TURRET WITH TORQUE, ARCH FORMING TURRETWITHOUT TORQUE,

40.Specification for Ultrasonic scaler (works without compressor)

Supply voltage:110-115-230 V~ 50/60 Hz . Max. power consumption:30 VA.Automatic Ultrasonic frequency: 28-36 kHz. Irrigation flow rate: 5-40 ml/min. Inbuilt cruise control system. Color coding system for various modes. In-built tank of 300 ml. Has periosteal pump (thus works without compressor).. Autoclavable, Newtron handpiece.