SPM-50 RF Spectrum Power Meter PC Software User Manual RF Spectrum Power... · 2018-12-17 · ShinewayTech RF Spectrum Power Meter PC software User Manual Shineway Technologies, Inc

SPM-50

RF Spectrum Power Meter

PC Software

User Manual

Shineway Technologies, Inc.

ShinewayTech RF Spectrum Power Meter PC software User Manual

Shineway Technologies, Inc. - 2 -

Notices

Copyright© 2014, ShinewayTech, All rights reserved. No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or translation into a foreign language) without prior

agreement and written consent from ShinewayTech as governed by international copyright laws.

Warranty

The material contained in this document is subject to change without notice.

ShinewayTech makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular

purpose. ShinewayTech shall not be liable for errors contained herein or for incidental or consequential damages in connection with furnishing, performance, or use of this material. The battery is a consumable part and is not subject to the SPM-50 warranty. ISO9001 Certification Produced to ISO9001 International Quality System Standard as part of

ShinewayTech, objective of continually increasing customer satisfaction through improved process control.



Safety Instructions

During each stage of operation of this instrument, please always observe the

following safety instructions. Not taking any safety precautions or following the

instructions will violate the safety standards of design, manufacturing and application

of these instruments. In no case will Shineway Technologies bear the responsibilities

for consequences incurred by violation of the following instructions.

Safety Terms Used in This Manual

The WARNING sign denotes a hazard. It calls attention to a

procedure, practice, or the like, which, if not correctly performed

or adhered to, could result in personnel injury. Do not proceed

beyond a WARNING sign until the indicated conditions are fully

understood and met.

The CAUTION sign denotes a hazard. It calls attention to an

operating procedure, or the like, which, if not correctly

performed or adhered to, could result in damage to or

destruction of part or the entire product. Do not proceed

beyond a CAUTION sign until the indicated conditions are fully

understood and met.

The NOTE sign information that may be beneficial during the

use and maintenance of the instrument.

Never connect or disconnect probe when RF signal is live,

emitted RF signal may harm human health.



Contents

Notices ................................................................................................................. 2

Warranty .............................................................................................................. 2

Safety Instructions ........................................................................................... 3

1. General Information .................................................................................. 6

1.1 Scope of this Manual ............................................................................................... 6

1.2 Unpacking and Inspection ....................................................................................... 6

1.3 Introduction ............................................................................................................. 7

2. Introduction ................................................................................................. 8

Software Interface ............................................................................................................... 8

2.1 Software Interface Description ................................................................................ 9

2.2 Software Menu Description ..................................................................................... 9

3. Basic Operation ....................................................................................... 11

3.1 Test Mode Selection .............................................................................................. 11

3.2 Sample Rate ........................................................................................................... 13

3.3 CCDF Threshold ................................................................................................... 13

3.4 Measure Time ........................................................................................................ 13

3.5 Unit ........................................................................................................................ 13

3.6 Power Limit ........................................................................................................... 13

3.7 User Information ................................................................................................... 14

3.8 Default Set ............................................................................................................. 15

4. Test Operation .......................................................................................... 16

4.1. Single Normal ........................................................................................................ 16

4.2. Single Burst Mode ................................................................................................. 16

4.3. Segment Sweep Mode ........................................................................................... 16

4.4. Result ..................................................................................................................... 16

5. Save and Review Test File ..................................................................... 17

5.1. Open File ............................................................................................................... 17

5.2. Save File ................................................................................................................ 17

5.3. Print Preview ......................................................................................................... 17

6. Specification ............................................................................................. 18

7. Maintenance and Calibration ................................................................ 19

7.1. Cleaning of Interfaces ............................................................................................ 19

7.2. Calibration Requirements ...................................................................................... 19



8. Warranty Information .............................................................................. 20

Terms of Warranty ............................................................................................................. 20

Exclusions ......................................................................................................................... 20

Warranty Registration ........................................................................................................ 20

Returning Instruments ....................................................................................................... 20

Contacting Customer Service ............................................................................................ 21



1. General Information

1.1 Scope of this Manual

Thank you for purchasing ShinewayTech instrument. Please read this manual

carefully before using any of ShinewayTech series fiber-optic instrument. Always observe the warnings and cautions appearing throughout this manual.

This manual contains the information necessary for proper operation and

maintenance of ShinewayTech SPM-50, troubleshooting instructions as well as information regarding obtaining services.

All ShinewayTech SPM-50 are carefully assembled and undergo a rigorous mechanical, electrical, and optical inspection prior to shipment. Beside the instrument, the package should also include a data transfer cable, a power adapter, a PC Analysis software installation disk and this users’ manual etc. For detailed information, refer to the packing list

Upon receiving the instrument, please check for any obvious signs of physical damage that may have occurred during shipment. Report any damage to the shipping agent or the representative of Shineway Technologies Inc. immediately. Retain the original packing materials in case reshipment becomes necessary.

1.2 Unpacking and Inspection

This instrument has been carefully packed in accordance with standard shipping procedures. Examine the instrument for damage that may have occurred during shipment. If you find any damage or the instrument is not working, or if any of the following items are not included, please contact your representative of Shineway Technologies, Inc.

If necessary, you may contact Shineway Technologies, Inc via this email: [email protected].

To return the instrument in the case of repair, calibration or other maintenance, please note the following: Be sure to pack the instrument with soft cushion like

Polyethylene, so as to protect the shell of the instrument.

Please use the original hard packing box. If use other packing material, please

ensure at least 3 cm soft material around the instrument.

Be sure to correctly fill out and return the warranty registration card, which

should include the following information: company name, postal address,

contact, phone number, email address and problem description.

Be sure to seal the packing box with exclusive tape.



Be sure to ship to your representative or the agent of the Company in a reliable

way.

1.3 Introduction

ShinewayTech RF Spectrum Power Meter PC software (the software) controls

SPM-50A to run measurement, display result on PC screen, export result to PC and

print report.

Function:

1. Automatic probe detection

2. Measurement settings, real time test display

3. Measurement mode: Single Normal, Single Burst, Segment Sweep

4. Measurement settings and result list

5. Power indicating dials

6. Histogram display

7. Max power & frequency point indication in Segment Sweep mode

8. Real time power & frequency correspondence in Segment Sweep mode

9. Histogram coordinates display in status bar

10. Alarm function

11. Open and save measurement data

12. Data preview and print



2. Introduction

Software Interface

Double click “RF Power Meter.exe” icon to run the software. The software interface

is shown below. When power meter probe is connected to PC via USB, the status

bar will display “Device: Online” in the right area.

Software Interface (Normal Mode)



2.1 Software Interface Description

Item Function

Menu Bar File management, parameter setup

Tool Bar Run test, stop test and mode switch

Information

Area Parameters, data and indicating dials display

Histogram Power per frequency points

Status Bar Device connection status, probe temperature

information

2.2 Software Menu Description

1. Menu Bar

Top Menu Sub Menu Function

File

Open File Open test result (.CSV file)

Save File Save test result (.CSV file)

Print Preview Preview results to be printed

Print Print test results

Settings

Measure Set

Mode (Single frequency point / Segment Sweep),

Frequency, Filter Type,

Sample Rate, CCDF Threshold, Unit (dBm,

mw/W)

Power Limit

When power limit is enabled, normal power is

shown in green, over-range power is shown in

Red.

User

Information Operator, Sample Type and Sample S/N

Default Set Load default settings, Single Normal as default

measurement mode

Help About Copyright



2. Tool Bar

Item Function

Run Start test

Stop Stop test

Normal / Burst

Mode Toggle between Normal / Burst mode

Measure Set

Mode (Single frequency point / Segment Sweep),

Frequency, Filter Type,

Sample Rate, CCDF Threshold, Unit (dBm, mw/W)

3. Information Area

Item Function

List Display measurement parameters and results

Indicating Dial Forward power and reflected power

Histogram Display historical data or frequency sweep data



3. Basic Operation

SPM-50A RF Spectrum Power Meter works in three modes:

1. Single Normal: Forward Power, Reflected Power, Return Loss, VSWR, Peak

Power, Crest, CCDF.

2. Single Burst: Burst, Burst Peak, Duty Cycle.

3. Segment Sweep: Forward Power, Frequency (Frequency of max forward

power), Mark (Input frequency to get corresponding power).

User need set measurement mode and frequency before test. If the signal to be

tested is modulated, sample rate is also to be set. When testing CCDF, user need to

set CCDF threshold. In segment sweep mode, user need set frequency range.

Typical operation guide:

3.1 Test Mode Selection



Single Normal

In “Measure Set”, select “Single”, click “Normal / Burst Mode” to select Single Normal

mode.

Single Burst

In “Measure Set”, select “Single”, click “Normal / Burst Mode” to select Single Burst

mode.

Segment Sweep

In “Measure Set”, set frequency range.

There are two ways to enter “Measurement Set”: Click “Measure Set” on Tool Bar or

select “Measure Set” from “Settings” Menu.

Frequency Setting

User need set frequency before test:

Measurement Settings

User can select Single or Segment Sweep mode, when in Single mode, user can



toggle between Single Normal and Single Burst by clicking “Normal / Burst Mode”

button on Tool Bar.

In Single Normal and Single Burst modes, user can manually set frequency

(400MHz~4000MHz) or select preset frequency ranges (Major mobile bands).

In Segment Sweep mode, user can manually set frequency range (Minimum

Difference from start frequency and stop frequency is 5MHz) or select preset

frequency ranges.

3.2 Sample Rate

User need set appropriate sample rate before testing modulated signals in “Measure

Set” menu. Available sample rates are: 5K, 30K and 300K. Higher frequency of the

modulated signal, higher sample rate.

3.3 CCDF Threshold

User need set CCDF threshold before CCDF test in “Measure Set” menu, the

threshold range is: 17dBm—57dBm.

3.4 Measure Time

Default test interval is 2 seconds and total time is 86400 seconds.

3.5 Unit

User can choose dBm or W/mW as power unit in “Measure Set” menu.

3.6 Power Limit

Click “Settings” menu to select “Power Limit”. When certain test item e.g. Forward

Power is over limit range, the power data will be displayed in red color.



Power Limit Menu

Check “Enable Warning” to enable Power Limit function.

Available power limits in each mode:

Single Normal mode: Forward Power, Reflected Power, Return Loss, Peak Power

Single Burst mode: Burst, Burst Peak

Segment Sweep mode: Forward Power

3.7 User Information

User can input: Operator, Sample Type and Sample S/N information and save them

to test results. Click “Settings” menu and select “User Information” to enter below

interface:

User Information



3.8 Default Set

Load default settings to Single Normal mode. Click “Settings” menu and select

“Default Set”.



4. Test Operation

After finishing test setup, user can start test in three supported modes: Single

Normal, Single Burst, and Segment Sweep.

4.1. Single Normal

Single Normal mode is to test continuous signal including continuous modulated

signals. Test items include: Forward Power, Reflected Power, Return Loss, VSWR,

Peak Power, Crest and CCDF.

4.2. Single Burst Mode

Single Burst mode tests the power, peak power and duty cycle of burst signal.

Set frequency and sample rate before test.

4.3. Segment Sweep Mode

Segment Sweep mode tests the frequency carried by the line.

Set frequency range before test.

4.4. Result

Click “Run” button on Tool Bar to start test.

Test result is displayed in three ways:

1. Result list in information area.

2. Indicating dial shows forward power or burst power.

3. Histogram shows historical test result of selected item or frequency sweeping

result.

Over-range test result will be displayed in red color.

In Single Normal or Single Burst mode, test will automatically stop at 86400 second

from start.



5. Save and Review Test File

5.1. Open File

User can open saved file (.CSV) in current test mode.

5.2. Save File

User can save test data in to .CSV file format.

Click “Files” menu and select “Save File”.

Default prefix of file name for each test mode respectively is:

“NData” for Single Normal mode, “BData” for Single Burst mode and “SData” for

Frequency Sweep mode.

5.3. Print Preview

User can preview the printing effect of current file (.CSV).



6. Specification

* Specifications subject to change without notice

Basic Specification

Frequency Range 400MHz ~ 4000MHz

Return Loss 0 ~ 23dB

Max Input Power 57dBm

Input VSWR <1.1

Insertion Loss ≤0.1dB

Directivity ≥30 dB (<3GHz); ≥28 dB (>3GHz)

Test Mode Segment Sweep / Single Normal / Single Burst

Segment Sweep Specification

Frequency Range 5M~3.6GHz

Frequency Resolution 10KHz

Frequency Stability ±2.5ppm

Filter Bandwidth (3dB) 1MHz

Power Range 10~57dBm

Power Accuracy ±0.8 dB

Power Measurement Specification

Power Range Average: 100mW ~ 200W (20 ~ 53dBm)

Peak: 100mW ~ 500W (20 ~ 57dBm)

Peak Average Ratio <12dB

CCDF 0.1 ~ 100%

Power Resolution ±0.01 dB

Power Accuracy (Single Normal)

±0.3dB (0℃ ~ +15℃ or +35℃ ~ +50℃ increase

±0.4dB) NOTE: lower 700MHz or higher 3300MHz, increase +3%

Burst Measurement Specification

Burst Width 30us ~ 80ms

Duty Cycle 0.001-1

Min. Measurement Frequency 12Hz

Average Burst Power 100mW~200W or 20~53dBm

General Specification

PC Connection USB

RF Port N-type female (50Ω)

Power Supply USB Power: 5V, 500mA

Power Consumption ≤ 2W

Working Temperature 0℃ ~ 50℃

Storage Temperature -20℃ ~ 70℃

Humidity 0 ~ 95% (Non-condensing)

Weight 495g

Dimensions 130×(95)×124×34mm (H × W × T)



7. Maintenance and Calibration

7.1. Cleaning of Interfaces

Safety instructions to be followed before cleaning

a) Make sure the instrument is power off when cleaning

b) Any operations contradict to the instructions may result in dangerous

radiation

c) Be cautious of electric shock and make sure AC power is disconnected

with the instrument before cleaning. Always use dry or moistest soft

cloth to clean the outside of the instrument, and never clean the inside

d) For maintenance, always go to qualified or certified professionals

e) Put cap on N-type port when port is not in use

7.2. Calibration Requirements

Calibration of the instrument is recommended every 3 years. Please contact our representatives or nearby customer service centers for proper calibration.



8. Warranty Information

Terms of Warranty

All ShinewayTech products are warranted against defective material and workmanship for a period of one (1) year from the date of shipment to the original customer. Any product found to be defective within the warranty period would be repaired or replaced by Shineway Technologies Inc. free of charge.

In no case will Shineway Technologies, Inc. liabilities exceed the original purchase

price of the product.

Exclusions

The warranty on your equipment shall not apply to defects resulting from the following:

Unauthorized repair or modification

Misuse, negligence, or accident

Shineway Technologies, Inc. reserves the right to make changes to any of its products at any time without having to replace or change previously purchased units.

Warranty Registration

A warranty registration card is included with the original shipment of equipment. Please take a few moments to fill out the card and mail or fax it to the local Customer Service Center of Shineway Technologies, Inc. to ensure proper initiation of your warranty term and scope of your warranty.

Returning Instruments

To return instrument for reasons of yearly calibration or other, please contact the local Customer Service Center of Shineway Technologies, Inc. to obtain additional information and a RMA# (Return Materials Authorization number). And describe briefly reasons for the return of the equipment, to allow us offer you more efficient service.

To return the instrument in the case of repair, calibration or other maintenance, please note the following:



Be sure to pack the instrument with soft cushion like Polyethylene, so as to

protect the shell of the instrument.

Please use the original hard packing box. If use other packing material,

please ensure at least 3 cm soft material around the instrument.

Be sure to correctly fill out and return the warranty registration card, which

should include the following information: company name, postal address,

contact, phone number, email address and problem description.

Be sure to seal the packing box with exclusive tape.

Be sure to ship to your representative or the agent of the Company in a

reliable way.

Contacting Customer Service

Please check our web site (www.shinewaytech.com) for updates to this manual and additional application information. If you need technical or sales support, please contact local Shineway Technologies Customer Service. Shineway Technologies (China), Inc.: Address: Fl.7, Zhongtai Plaza, No.3 Shuangqing Rd, Haidian District, Beijing,

China Postal code: 100085 Tel: +86-10-62953388 Fax: +86-10-62958572 Email: [email protected] WEB: www.shinewaytech.com

THANK YOU FOR CHOOSING SHINEWAY TECHNOLOGIES!

Documents

SPM-50 RF Spectrum Power Meter PC Software User Manual RF Spectrum Power... · 2018-12-17 · ShinewayTech RF Spectrum Power Meter PC software User Manual Shineway Technologies, Inc