Upload
paulo-ferreira
View
225
Download
0
Embed Size (px)
Citation preview
8/17/2019 SSD 500(1B)Disassembling
1/21
M11201~M11300
M11451C~
S/N
:
ApplicableSerial Numbers :
8/17/2019 SSD 500(1B)Disassembling
2/21
DSC PC
(EP519200 / EP519201 EP519900 )
DSC PC boards
PNL-500
Operating panel assembly
(PSU-S500 )
Power supply unit
(IP-0702 )
Monitor unit
PC
(EP518500 EP518600 )
Transmitting and
receiving PC boards
8/17/2019 SSD 500(1B)Disassembling
3/21
M5.5 M6 Box driver 1
M5.5 M6 1
8/17/2019 SSD 500(1B)Disassembling
4/21
Probe Holder Connextor Cover Rear Cover
PC
Operation panel
assembly and PC BoardLeft Shield Cover
Right Shield Cover
Front Cover
DSC PC CPU
DSC PC Board (CPU)
Tx & Rx PC Rx
Tx & Rx PC Board (Rx)
CRT-PC
CRT- PC Board
PC
Rear Blocking PC Board
Power Supply Unit
DSC PC DIU
DSC PC Board (DIU)
Tx & Rx PC Tx
Tx & Rx PC Board (Tx)
8/17/2019 SSD 500(1B)Disassembling
5/21
8/17/2019 SSD 500(1B)Disassembling
6/21
8/17/2019 SSD 500(1B)Disassembling
7/21
8/17/2019 SSD 500(1B)Disassembling
8/21
7. 7. Left-Right shield cover dismounting procedure
7-1
(1) 19 7-2
(1) 28
7-1 Left shield cover dismounting procedure
(1)Remove the 19 screws at the left side, and remove the left shield cover. in Fig.
7-2 Right shield cover dismounting procedure
(1)Remove the 28 screws at the right side, and remove the right shield cover. in Fig.
A
B
A
B
BNK3 8 Fe,Ni, 28
Right shield cover B
BNK3 8 Fe,Ni, 19
Left shield cover
A
8/17/2019 SSD 500(1B)Disassembling
9/21
8. 8. Front cover dismounting procedure
(1) (2)
(3) (4) P302 P210 P7
(1)Loosen the two screws at both side of the bottom. in Fig.
(2) While keeping the front cover from failing downward by holding it with the hand, remove
the four screws, and loosen one screw. in Fig.
(3)Extract the front cover forwards while looking wiring. in Fig.
(4)Remove three cables (P302 P210 P7) , and remove the front cover. in Fig.
A
B
C
D
A
B
C
D
,1
Screw to be loosened
,4
Screw to be removed
B
(BNK4 10),2
Screw to be loosened
Front cover
C
A
D
D
P7
P210 D
P302
BNK3 8, 3
BNK4 10, 2
8/17/2019 SSD 500(1B)Disassembling
10/21
9.PC
9.Operating panel assembly,and PC board dismounting procedure
9-1 (PNL-500*)
(1) PC P304 P308 P302 3 (2) (3) PC P311 (4) (L-KEY-58*-1/EP490500**)
(5) P309 P312 P314 (L-KEY-58*-1
/EP490500**)
9-1 Operation panel assembly (PNL-500*) dismounting procedure
(1) Remove three connectors (P304, P308, P302) connected to the PC board. in Fig.
(2) Remove the 20 screws, and remove the front shield. in Fig.
(3) Remove connector (P311) connected to the PC board. in Fig.
(4) Remove the four spacers, and lift the top part of operation panel assembly (L-KEY-58*-1
/EP490500**). in Fig.
(5) Remove the three connectors (P309, P312, P314), and remove the operation panel
assembly (L-KEY-58*-1/EP490500**). in Fig.
A
B
C
D
E
A
B
C
D
E
C
D
P311
: TSB-311, 4
Spacer: TSB-311, 4
BNK3 8 Fe,Ni, 10
P tight 3 8 Fe,Ni, 6
CNK3 8 Fe,Ni, 4
Front shield
P304
P308
P302
A
B
A
P312 P314
(L-KEY-58*-1/EP490500**)
Operation panel assembly
E
P309
8/17/2019 SSD 500(1B)Disassembling
11/21
P tight round head screw
3 x 8, 7
P 3 x 8, 7
P tight round head screw3 x 6, 2
P 3 x 6, 2
7
(L-KEY-58*-2/EP490400**)
Full keyboard
seven screws
(L-KEY-58*-2 / EP490400**) dismounting procedure
(L-KEY-58*-2 / EP490400**)
full-keyboard (L-KEY-58*-2/EP490400**).
(L-KEY-58*-2/EP490400**)
9-2
9-2
8/17/2019 SSD 500(1B)Disassembling
12/21
9-3 PC (L-KEY-58*-3 / EP490600**)
PC (L-KEY-58*-3/EP490600**)
9-4 PC (EP510100 )
PC (EP510100 ) 9-5 PC (EP490700 )
PC (EP490700 )
9-3 PC board (L-KEY-58*-3 / EP490600**) dismounting procedure
Remove the knob on the front side of front cover, then remove two screws, and remove
the PC board (L-KEY-58*-3/EP490600**). in Fig.
9-4 PC board (EP510100**) dismounting procedure
Remove the two screws, and remove the PC board (EP510100**). in Fig.
9-5 PC board (EP490700**) dismounting procedure
Remove the two screws, and remove the PC board (EP490700**). in Fig.
A
B
C
A
B
C
CPC (EP490700 )
PC board
P tight 3 8 Fe,Ni, 2
A
Front Cover
STC
STC Knob Knob
A
PC
(L-KEY-58*-3/EP490600**)
PC board
P tight 3 8 Fe,Ni, 2
B
PC (EP510100
PC board
)
P tight 3 8 Fe,Ni, 2
8/17/2019 SSD 500(1B)Disassembling
13/21
10. PC 10. PC boards dismounting procedure
10-1 DSC PC (CPU: EP519900 )
(1) P405 (2)PC P301 P405 2 (3) PC
10-1 DSC PC board (CPU: EP519900**) dismounting procedure
(1) Remove the one screw, and remove the cable (P405) from the shield case. in Fig.
(2) Remove two connectors (P301·P405) connected to the PC board. in Fig.
(3) Remove the six screws, and remove the PC board. in Fig.
A
B
C
A
B
C
BNK3 8 Fe,Ni, 6
B
C
PC (CPU: EP519900 )
PC board (CPU: EP519900 )
P405
P301
BNK3 8 Fe,Ni, 1
Shield case
A
8/17/2019 SSD 500(1B)Disassembling
14/21
10-2 DSC PC (DIU: EP519200 )
(1) P404 (2) PC P213 P212 P404 3 (3) DIU 2 2 4
4 (4) PC
10-2 DSC PC board (DIU: EP519200 ) dismounting procedure
(1) Remove the one screw, and remove the cable (P404) from the shield case. in Fig.
(2) Remove three connectors (P213 P212 P404) connected to the PC board. in Fig.
(3) Remove the total four screws (each two screws), and remove the two DIU cable earth
at the top. Remove the four screws, and remove the flat cable cover. in Fig.
(4) Remove the six spacers, and remove the PC board. in Fig.
A
B
C
D
A
B
C
D
Flat cable cover
DIU
DIU cable earth
DIU
DIU cable earth
BNK3 8, 4
CNK3 8, 4
D
P212
P404
P213
BNK3 8 Fe,Ni, 1
Shield case
AB
B
PC (DIU: EP519200 )
PC board (DIU: EP519200 )
(M6 )
Spacer
(M6 Box driver)
C
8/17/2019 SSD 500(1B)Disassembling
15/21
10-3 PC (Rx: EP518500 )
(1) P402 P403 (2)PC P204 P402 2 (3) PC
10-4 PC (Tx & Control: EP518600 )(1) PC P208 P403 2 (2) PC
10-3 Rx PC board (Rx: EP518500 ) dismounting procedure
(1) Remove the one screw, and remove the cable (P402·P403) from the shield case. in Fig.
(2) Remove two connectors (P204·P402) connected to the PC board. in Fig.
(3) Remove the six screws, and remove the PC board. in Fig.
10-4 Tx PC board (Tx & Control: EP518600 ) dismounting procedure
(1) Remove two connectors (P208·P403) connected to the PC board. in Fig.
(2) Remove the six spacers, and remove the PC board. in Fig.
A
B
C
D
E
A
B
C
D
E
P208
P403
E
PC (Tx: EP518600 )
PC board (Tx: EP518600 )
(M6 )
Spacer
(M6 Box driver)
D
P204
P402
C
B
PC (Rx: EP518500 )
PC board (Rx: EP518500 )
BNK3 8 Fe,Ni, 1
Shield case
A
BNK3 8 Fe,Ni, 6
8/17/2019 SSD 500(1B)Disassembling
16/21
11. PC 11. Rear blocking PC board dismounting procedure
11-1
(1)PC P204 P213 2 (2) 4 DIU (3) (4) 8
11-1 Rear blocking plate dismounting procedure
(1) Remove two connectors (P204, P213) connected to the PC board. in Fig.
(2) Remove the four screws, and remove the DIU cable earth, then remove the cable. in Fig.
(3) Remove the cable from the cable-clamp and fan fitting plate. in Fig.
(4) Remove the eight screws, and remove the rear blocking plate. in Fig.
A
B
C
D
A
B
C
D
DIU
DIU cable earth
P204
BNK3 8 Fe,Ni, 2
BNK3 8 Fe,Ni, 2
P213
DIU
DIU cable earth
B
A
B
A
Rear blocking plate
Cable-clamp
D
BNK3 8 Fe,Ni, 8
C
8/17/2019 SSD 500(1B)Disassembling
17/21
11-2 PC
(1) 2 BNC (2) 2 (3) 4
(4)PC P505 (5) 3 PC
11-2 Rear blocking PC board dismounting procedure
(1) Remove the two screws, and remove the BNC shield cover. in Fig.
(2) Remove the two screws, and remove the fixture pushing cable. in Fig.
(3) Remove the four screws, and remove the rear blocking cover. in Fig.
(4) Remove connector (P505) connected to the PC board. in Fig.
(5) Remove the three screws, and remove the PC board. in Fig.
A
B
C
D
E
A
B
C
D
E
BNK3 8 Fe,Ni, 1
BNC
BNC shield cover
A
BNK3 8 Fe,Ni, 2
Fixture pushing cable
B
BNK3 8 Fe,Ni, 3
P505
PC (EP510200 )
PC board (EP510200 )
BNK3 8 Fe,Ni, 1
Rear blocking cover S3 6, 2
BNK3 8 Fe,Ni, 1
ED
C
8/17/2019 SSD 500(1B)Disassembling
18/21
12. 12. Power supply unit dismounting procedure
12-1
(1) 1 P404 (2)PC P403 P404 2 (3) 6
12-1 Power supply unit shield cover dismounting procedure
(1) Remove the one screw, and remove the cable (P404) from the shield case. in Fig.
(2) Remove two connectors (P403, P404) connected to the PC board. in Fig.
(3) Remove the six screws, and remove the power supply unit shield cover. in Fig. When it fix the power supply shield cover, make the cable never pile up, and be caught
the all cables between the gaskets. in Fig.
A
B
C
D
A
B
C
D
D
P403
P404
BNK3 8 Fe,Ni, 6 BNK3 8 Fe,Ni, 1
Power supply unit shield cover
Shield case
C
B
B
A
D
8/17/2019 SSD 500(1B)Disassembling
19/21
12-2
(1) P406 P407 2 (2) 2
12-2 Power supply unit dismounting procedure
(1) Remove two connectors (P406·P407) connected to the power supply unit. in Fig.
(2) Remove the two screws, and remove the power supply unit. in Fig.
A
B
A
B
S3 8 Fe,Ni, 2
Power supply unit
B
Power supply unit
A
P407 P406
8/17/2019 SSD 500(1B)Disassembling
20/21
13. CRT-PC 13. CRT-PC pull-out procedure
13-1
(1)
(2) 9 DIU (3) GEU (4) 9 GEU
13-1 Shield case dismounting procedure
(1) Remove the one screw at the under side of the fan fitting plate. Loosen four screws,
and shift the fan fitting plate upward so that the ground shaped holes are released, then
remove the fan fitting plate. in Fig.
(2) Remove the nine screws, and remove the DIU shield case. in Fig. (3) Remove the insulation sheet from the GEU shield case. in Fig.
(4) Remove the nine screws, and remove the GEU shield case. in Fig.
A
B
C
D
A
BC
D
DIU
DIU shield case
S3 6 Fe,Ni, 9
C
S3 6 Fe,Ni, 9
Insulation sheet
DIU
DIU shield case
D
B
BNK3 8 Fe,Ni, 1
Screw to be removed
FAN fitting plate
Ground shaped hole BNK3 8 Fe,Ni, 4
Screw to be loosened A
8/17/2019 SSD 500(1B)Disassembling
21/21
13-2 CRT-PC
(1) 8 (2) 1 CRT-PC
13-2 CRT-PC board pull out-procedure
(1) Remove the eight screws, and remove the top cover. in Fig.
(2) Remove the one screw, and pull out the CRT-PC. in Fig.
A
B
A
B
CNK3 6 Fe,Ni, 1
B
CRT-PC
CRT-PC
S3 6 Fe,Ni, 8
Top cover
A