corporatet (877) SSL-GREENf (630) 889-8106 3609 Swenson Ave. St. Charles, IL 60174

THIS DOCUMENT IS THE PROPRIETARY PROPERTY OF SOLID STATE LUMINAIRES. ANY UNAUTHORIZED TRANSFER, USE OR REPRODUCTION IS STRICTLY PROHIBITED. ©2017 SOLID STATE LUMINAIRES.

SSL-UNLE - INSTALLATION INSTRUCTIONS part 1 POWER CONNECTIONS

CAUTION: BEFORE CONNECTING THE FIXTURE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.

DETAILED ILLUSTRATION

GENERAL:1. Before starting the installation, make sure all electricity has been turned

off and electrical breaker has been locked out and tagged out.

2. To ensure the success of the installation, be sure to read these instructions and review the diagrams thoroughly before beginning.

3. All electrical connections must be in accordance with local codes, ordinances, or the National Electrical Code.

SAFETY INFORMATION:The UNDERLINE series is for indoor use only. The LED module is not protected against short circuits, overload or overheating; therefore you must use an electronically stabilized power supply that offers protection against the previously mentioned safety risks. SSL power supplies are specifically designed with protection features for safe operation.

wARNING: If a non Solid State Luminaires power supply is used to power the fixtures, the manufacturer warranty will be voided.

INSTALLATION1. Determine all measurements for installation (Fig.1)

2. Add fixture lengths to less than the measured space to allow for cords and connectors. (Fig 2)

IMPORTANT: Include cord length and fixture components when adding total length. See specification sheets for component dimensions.

3. Determine power layout. See (Fig 3)wARNING: Each max run length must not exceed 36W of power consumption.NOTE: A run is all devices directly connected to power supply.

wARNING: Do not open, alter or tamper with the fixture housing. This will void the manufacturer’s warranty. To avoid electrical shock, never open the UNL fixture housing. Do not attempt to service the electronic components yourself. Non-expert handling may damage the product and cause injury to the user.

24V DC Power

FIG-3

100W Power

FIG-1

Sample Surface Areas

––––––––––––– 36" ––––––––––––– ––––––––––––––––– 43" –––––––––––––––––

––– 11.9" ––– –––––– 19.8" –––––– –––––– 19.8" –––––––––––– 19.8" ––––––

Include Straight Connector + .625" - Include 1.5” Cord Allowance per Fixture

PowerTotal length from this example:11.9" + .625" + 19.8" + 1.5" = 33.825"UNLE-1 UNLE-2

UNLE-1 UNLE-2

18W CC3 CC6

4S

UNLE-3 UNLE-3

18W

UNLE-1

6W

UNLE-1

6W

UNLE-2

12W 12W

UNLE-2

Total Watts= 364S

Total Watts = 36

FIG-2

Direct Connections

RF Rev 0117

corporatet (877) SSL-GREENf (630) 889-8106 3609 Swenson Ave. St. Charles, IL 60174

THIS DOCUMENT IS THE PROPRIETARY PROPERTY OF SOLID STATE LUMINAIRES. ANY UNAUTHORIZED TRANSFER, USE OR REPRODUCTION IS STRICLY PROHIBITED. ©2017 SOLID STATE LUMINAIRES.

SSL-UNLE - INSTALLATION INSTRUCTIONS part 2 MOUNTING INSTRUCTIONS

CAUTION: BEFORE CONNECTING THE FIXTURE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.

DETAILED ILLUSTRATION24V DC Power

GENERAL:1. Before starting the installation, make sure all electricity has been turned off and

electrical breaker has been locked out and tagged out.

2. To ensure the success of the installation, be sure to read these instructions and review the diagrams thoroughly before beginning.

3. All electrical connections must be in accordance with local codes, ordinances, or the National Electrical Code.

SAFETY INFORMATION:The UNDERLINE series is for indoor use only. The LED module is not protected against short circuits, overload or overheating; therefore you must use an electronically stabilized power supply that offers protection against the previously mentioned safety risks. SSL power supplies are specifically designed with protection features for safe operation.wARNING: If a non Solid State Luminaires power supply is used to power the fixtures, the manufacturer warranty will be voided.

MOUNTING INSTRUCTIONS1. Screws are provided in each fixture package. You may use different screws if

longer ones are required (sold by others).

2. Align mounting bracket MC-E provided with mounting surface. (Fig.1)

3. Screw the mounting bracket to the mounting surface. (Fig. 2)

4. Push fixture into mounting bracket. (Fig. 3)

5. Connect all fixtures and accessories following part 1 (Power) of installation instructions.wARNING: Each max run length must not exceed 36W of power consumption. Read page 1 before proceeding with power connections.NOTE: A run is all devices directly connected to power supply.

6. Plug in power cable to the fixture.

FIG-1

Align Mounting Clip bracket to surface.

Screw the Mounting Clip bracket to surface.

FIG-2

Push fixture into bracket.

FIG-3

MC-E Mounting Clip attaches to surface using screws provided.