Upload
angelochintu
View
1.035
Download
3
Embed Size (px)
DESCRIPTION
Citation preview
SLSB LLCCONSTRUCTION FASTENER MANUFACTURERS
SINCE 1887
St. Louis Screw & Bolt (SLSB LLC) is oneof the oldest domestic bolt manufacturers in theUnited States, with bolts in many well-known civilengineering projects in the US and the world. St.Louis Screw & Bolt stocks everything a bridge orsteel fabricator might need to complete a major pro-ject.
SLSB’s experienced personnel provide servicebefore, during and after the sale by providing infor-mation on the availability of structural products andHONEST lead times. The structural fastener buyerWILL find SLSB’s combination of the country’s mostdiverse structural bolt inventory and ability to manufacture specials in-house are what makesSLSB a complete one stop source for all their structural fastener requirements.
Structural Bolts
• A325 type I & type III • Hex Heads• A490 type I & type III • Countersunk Heads• A449 • Dome Heads• A307-A & A307-B • Carriage Heads• A354-BD • Special Heads
TC Bolts• F1852 type I & type III • A490• Mechanically Galvanized
Anchor Bolts• ASTM F1554 Grade 36 • ASTM F1554 Grade 105• ASTM F1554 Grade 55 • 304, 316 A193-B7 A193-B8 & A449
Fabricated Rod Products• Tie Rod Assemblies • Eye Bolts• U-Bolts • J-Bolts
Stocked Finishes• Plain • Mechanically Galvanized• Hot Dip Galvanized • Zinc Plated
Other grades of domestically produced steels are available for those special needs customers might face.
Diameters from 1/2" through 4" Up to 40 feet in length
With the ability to ship to every state in the USA and any foreign country, SLSB is a global supplier.
St. Louis Screw & Bolt is a charter member of the Industrial Fastener Institute (IFI) andwas instrumental in the passage of the Fastener Quality Act (FQA). SLSB is also an associatemember of the American Institute for Steel Construction (AISC) and the National Steel BridgeAlliance (NSBA). SLSB’s in house quality lab is A2LA certified and CALTRANS approved.
ASTM A325 Type I Standard
ASTM A325 Type III Weathering
ASTM A490 150,000 Min. Tensile
A449 Gr. 5
Heavy Hex Head, Button Head Shear andSlotted Countersunk Bolts
1⁄2" through 11⁄2" in Diameter
Specials, made to customer’s drawings
Standard and Special Lengths AvailableIn Stock in Our Warehouse
Plain, Hot Dip Galvanized or Mechanical Galvanized
A563 Gr. DH, Gr. A, A194 Gr. 2H Heavy HexNuts
Direct Tension Indicator Washers ASTM F959
Electric Wrenches for Shear Bolts and HeavyHex Bolts
Sales, Repairs and Replacement Parts for Wrenches
Jobsite Bolt Tension Calibration Inspections
In House Rotational Capacity Testing
Complete Mill Traceability and CertificationAvailable
F436 Heavy Structural Washers
STRUCTURAL BOLTS: Heavy Hex, Tension Control, Heavy Hex Nuts & Washers
Anchor Bolts
Plates
Round U Bolts
Square U Bolts
Threaded Rebar
Rod Couplings
Tie Rods
Eye Bolts & Rods
Welded Assemblies
Wilson Sleeves
Threaded Studs
STEELS — ASTM F1554 Grades 55 and 105, A588, A325, A449,A490, A354, A193
STAINLESS STEELS — AlSl Type 304, 316, 410
Nickel Alloys
1⁄2 to 4" in Diameter–Any Length
Turnbuckles
Clevises
FABRICATED STEEL COMPONENTS FOR CONSTRUCTION
Hex and Square Head Bolts with Extra Thread
Tie Rods: 1⁄2" to 4" in Diameter, Any Length
Dock Washers
OGEE Washers
Plate Washers
All Thread Rod Galvanized
Dock Spikes, Dome Head and Countersunk Head Bolts
Lag Screws up to 11⁄2" in Diameter
Stainless Steel and Nickel Alloys
Epoxy Coatings Available
HOT DIP GALVANIZED MARINE HARDWARE
On the Shelf — Ready for Pickup or Delivery
Plain, Stainless Steel and Hot Dip Galvanized
For Concrete, Block or Hollow Wall Masonry
Epoxy Anchor Systems with Threaded Studs
Stocking Popular Brand Names
MASONRY ANCHORS
6900 N. Broadway St. Louis, MO 63147800-237-7059 Fax: 314-389-7510
www.stlouisscrewbolt.com
TC Wrench TC Indexable Grip
Simple Torqon
St. Louis Screw & BoltTABLE OF CONTENTS
TONE Shear WrenchOperating Methods & Specifications . . . . . . . . . . . . . . . . . . . . . . . . 1
Tone Mid-Size Shear Wrench – S-60EZA . . . . . . . . . . . . . . . . . . . . 2
Tone Heavy Duty Shear Wrench – S-90EZ & S-110EZ . . . . . . . . . . 3
Tone Corner Shear Wrench – S-80EZ. . . . . . . . . . . . . . . . . . . . . . . 4
Tips & Problem Solving Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . 5
TONE Indexable Grip Type Shear WrenchSpecifications – M-221HRZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TONE Simple Torqon Electric WrenchSpecifications – SR31E, SR51E, SR71E. . . . . . . . . . . . . . . . . . . . . 7
Specifications – SR121E, SR211E, SR171E . . . . . . . . . . . . . . . . . . 8
Bar Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6900 N. Broadway St. Louis, MO 63147800-237-7059 Fax: 314-389-7510
www.stlouisscrewbolt.com
1 www.stlouisscrewbolt.com
OPERATING METHODS
• Insert bolt into the work, then put washer, turn nut through to make primary tightening.
� Place bolt thru hole in the joining members.
� Attach washer & run up nut finger tight to the working members.
� Fit the inner socket firmly over the bolt tip (spline).
� Engage the outer socket over the nut by pushing the wrench.
� Pull lever switch to on. The outer socket rotates the nut until the torque control groove in the spline shears off, thereby achieving proper bolt tension.
� Turn off wrench when bolt tip (spline) shears off.
� Pull the wrench back to remove outer socket from the nut.
Pull the eject lever on the wrench to discharge the severed bolt tip (spline) from the inner socket.
(Fig.1)
Model
S-60EZAS-90EZS-110EZS-80EZ
MaximumTorque(lbf•ft)435595747595
Voltage (v)
SinglePhase
115
No-loadSpeed(rpm)22(20)15(16)16(16)12(12)
Weight(lb.)13192818
ApplicableBolt Dia.
7⁄8"1"
11⁄8"1"
SPECIFICATIONS
TONE Shear Wrench
2 www.stlouisscrewbolt.com
TONE MID-SIZE SHEAR WRENCH
S-60EZASIZE RANGE5/8" Ø & 3/4" Ø A325 ASTM F1582/A325 & A4907/8" Ø ASTM F1852/A325
Accessories
1. Steel case2. Interchangeable (-) screw driver for socket.3. Inner socket for 3/4"4. Outer socket for 3/4"
TONE S-60EZA Dimensional Drawing(For specifications, refer to separate chart)
Subject to change through improvement without previous notice.
13"
12"
4"
6"
8"
3.3"
2.4"
2.1"
TONE Shear Wrench
3 www.stlouisscrewbolt.com
TONE HEAVY DUTY SHEAR WRENCH
Accessories
1. Steel case2. Interchangeable (-) screw driver for socket.3. Inner socket for 1"4. Outer socket for 1"
Accessories
1. Steel case2. Interchangeable (-) screw driver for socket.3. Inner socket for 1"4. Outer socket for 1"
S-90EZ S-110EZSIZE RANGE3/4"Ø & 7/8"Ø ASTM F1852/A325 & A4901"Ø ASTM F1852/A325
TONE S-90EZ Dimensional Drawing(For specifications, refer to separate chart)
Subject to change through improvement without previous notice.
SIZE RANGE1"Ø & 1 1/8"Ø ASTM F1852/A325 & A490
TONE S-110EZ Dimensional Drawing(For specifications, refer to separate chart)
Subject to change through improvement without previous notice.
16"
8"
ø2.2"
ø2.8"
ø3.8"
17"
9"
ø2.5"
ø3.2"
ø4.5"
TONE Shear Wrench
4 www.stlouisscrewbolt.com
TONE CORNER SHEAR WRENCH
S-80EZSIZE RANGE3/4"Ø & 7/8"Ø ASTM F1852/A325 &A4901"Ø ASTM F1852/A325
Accessories
1. Metal case2. Instruction Manual3. Screwdrive4. Inner sockets for 3/4", 7/8" & 1"5. Outer sockets for 3/4", 7/8" & 1"6. Connector
TONE S-80EZ Dimensional Drawing(For specifications, refer to separate chart)
Subject to change through improvement without previous notice.
The S-80EZ was developed for use on bridge U-ribs, truss joints, and other confined loca-tions where conventional shear wrenches cannot be used.
23"
2.7"
3.8"
8.4"
2.1"
TONE Shear Wrench
5 www.stlouisscrewbolt.com
TIPS & PROBLEM SOLVING SOLUTIONSSTAYING OUT OF TROUBLE AT THE JOB SITE
I. VERIFY BOLT TENSION AT THE JOB SITEA) Review the basic calibrator set up as described for a bolt tension calibrator such as a Skidmore-Wilhelm.B) Be sure that the unit is in calibration and that adapters for tension control bolts are in the unit.C) Review the instructions for use of the calibrator and test the assembly.D) It is recommended that the test procedure be performed three times, each time with a new fastener set
selected from the same lot intended to be used in the actual bolted connection. The actual number of tests is at the discretion of the inspector.
II. INSTALLATION PROBLEMSA) Bolt breaks at the threaded portion before the pintails shears off?
Answer: Most likely the torque co-efficiency value has become lower.Possible Causes:
1) Storage conditions allowing exposure to rain, water, moisture, high humidity, temperatures over 140˚F or similar environmental conditions.
2) Lubrication of the product beyond “as delivered” condition from the factory. (Use of oil, grease, or wax on the product components at the job site)
3) Adhesion of oil, paint, mill scale, dirt burrs, or foreign material on the faying surfaces which may allow rotation of the bolt, or rotation of the washer with the nut during the tightening operation.
4) Not properly making the connection “snug” tight before final wrench tightening which may allow the bolt to rotate.(Same as common hex bolt)
5) Possible misalignment of the connection surfaces that may prevent proper contact of the head and faying surface.
6) Exposure to the environment over an extended period before final tightening.
B) Pintail breaks at the shear groove before joint connection is made or before specified fastener tension isachieved.
Answer: Most likely the torque coefficiency value has become higher.Possible Causes:
1) Storage and handling conditions allowing sand, dirt or other foreign material to accumulate on the threads of the bolt or nut.
2) Rough handling of the fasteners that would cause nicks or gouges on the bolt and nut.3) Exposure to environmental conditions that cause rust to form on the threads of the bolt, nut or
washer face.4) Failure to follow AISC procedures for initial tightening in bringing all plies of the joint into firm contact
before final tightening. (ie, trying to draw the distorted plies together and shearing the pintail before the plies are in contact rather than sequentially tightening, or using “fit up” bolts to draw them together) On a T.C. bolt, the pintail will shear off when too great a torque is applied. Whereas a hex bolt may be torqued beyond the plastic limit of the bolt without the knowledge of the installer when pulling the distorted steel together.
III. CAUSE OF WRENCH PROBLEMS (See wrench booklet for instructions)A) Pintail does not discharge from socket.
1) Check inner socket for abrasions or upsets. Remove and replace socket2) Check inner socket for rust, sand, dirt, oil or other foreign material caused by poor handling or care in the field.
Clean inner socket and replace if necessary.3) Check bolt pintail for foreign material as a result of poor handling in the field. Remove foreign material from pintail,
or discard the T.C. assemblies that are contaminated. DO NOT remove lubrication from “as received” products nor re-lubricate.
4) Check ejector pin and spring for contamination. Disassemble and clean components. Replace spring if broken, and pin if worn.
5) Check sockets for wear. Replace if necessary.
B) Socket does not engage properly with pintail or nut.1) Check serrations of the socket for wear. Replace sockets if necessary.2) Check socket size to be sure correct size for the fastener is being used. An oversized socket will wear faster and
create tightening problems.TSW-5/01
TONE Shear Wrench
Indexable Grip
6 www.stlouisscrewbolt.com
Based on M221EZ wrenches, thiswrench has a special feature, thatthe grip can be indexed at every90 degrees and locked.
At 180 degrees, upper use is madeeasier while operator stays abovebeam.
At 90 degrees, tightening bolts onthe web is made easier.
SPECIFICATIONS
Indexable Angles: 0, 90, 180 & 270°
ACCESSORIES INCLUDED1) 3/4” Inner & Outer Sockets (1 pc.) 4” Long2) Screw Driver (-)3) Connector (115V only)4) Instruction Manual5) Metal Case
OPTIONAL ACCESSORIES7/8” Inner & Outer Sockets 4” Long3/4” & 7/8” Short Inner & Outer Sockets
1-1/2” Long
MODEL M-221HRZVoltage(S) 115VMax. Current 13.5AFrequency 50/60HzMax. PowerConsumption 1300WRated Max. Torque 544 ft. lbs.Free Rotation 19 rpmWeight - SS Model 13.3 lbs.Weight - LS Model 16.0 lbs.
EXTERNAL DIMENSIONS
M-221HRZ for 3/4” A325, A490 and 7/8” ASTM F1852/A325 Tension Control Bolts
SHORT SOCKET WRENCH SHOWN
INDEXABLE GRIP TYPE SHEAR WRENCHNEW
Simple Torqon Electric
7 www.stlouisscrewbolt.com
TORQON ELECTRIC ADJUSTABLE TORGUE CONTROL WRENCH
Model SR31E SR51E SR71E
L 9 – 10 1/2" 9 3/8 – 10 5/8" 9 3/4 – 11"
L1 4 – 5 1/4" 4 1/8 – 5 1/2" 4 5/8 – 5 7/8"
L2 1 5/8 – 2 7/8" 1 5/8 – 2 7/8" 1 5/8 – 2 7/8"
H 9 7/8" 10" 10 1/4"
ØD 2 1/4" 2 5/8" 3"
Ød 2 1/8 – 3 1/2" 2 1/8 – 3 1/2" 2 1/8 – 3 1/2"
SR31E, SR51E, SR71E for Hexagonal Bolts
� Torque control functions in both directions.� Non-impact, very smooth and high precision
wrench of a new design. Simple to set targetedtorque and easy and comfortable to operate.
� No separate control unit, as the torque control device is built into the main body. The wrench design is compact, light in weight and well-balanced.
� Socket with reaction bar turns independently to a certain angle to make it easier to insert socket into the nut.
� Main body will stand still during the movement of the reaction bar until it makes contact with opposing resistance i.e. another bolt or the structure.
ModelSize Range
Voltage(S)
Max. Current
Frequency
Power Consumption
Controllable Range
Free Rotation
Weight (Mainbody)
SR31E5/8 Ø A325 & A490
115V
13.5 A
50/60 Hz
max 1100 W
150~300 N•m
110~220 lbf•ft
31 rpm
9.5 lb
SR51E5/8 Ø A325 & A490
3/4 Ø A325
115V
13.5 A
50/60 Hz
max 1100 W
300~500 N•m
220~370 lbf•ft
25 rpm
11.2 lb
SR71E3/4 Ø A325 & A490
7/8 Ø A325
115 V
13.5 A
50/60 Hz
max 1100 W
350~700 N•m
260~520 lbf•ft
17 rpm
12.1 lb
ACCESSORIES1) 1pc. Bar Socket 3) Metal Case2) Screw Driver (-) 4) Instruction Manual
SPECIFICATIONS
Simple Torqon Electric
8 www.stlouisscrewbolt.com
TORQON ELECTRIC ADJUSTABLE TORGUE CONTROL WRENCH
SR121E, SR211E, SR171E for Hexagonal Bolts
� Torque control functions in both directions.� Non-impact, very smooth and high precision
wrench of a new design. Simple to set targetedtorque and easy and comfortable to operate.
� No separate control unit, as the torque control device is built into the main body. The wrench design is compact, light in weight and well-balanced.
� Socket with reaction bar turns independently to a certain angle to make it easier to insert socket into the nut.
� Main body will stand still during the movement of the reaction bar until it makes contact with opposing resistance i.e. another bolt or the structure.
ModelSize Range
Voltage(S)
Max. Current
Frequency
Power Consumption
Controllable Range
Free Rotation
Weight (Mainbody)
SR121E7/8 Ø A325 & A490
1 Ø A325
115V
15.0 A
50/60 Hz
max 1400 W
600~1200 N•m
450~900 lbf•ft
16 rpm
19.4 lb
SR211E1 Ø A325 & A490
1 1/8 Ø A325 & A490
1 1/4 Ø A325
115V
12.0 A
50/60 Hz
max 1100 W
1000~2100 N•m
750~1550 lbf•ft
4 rpm
38.6 lb
SR171E1 Ø A325 & A490
1 1/8 Ø A325 & A490
115V
12.5 A
50/60 Hz
max 1200 W
850~1700 N•m
630~1250 lbf•ft
6 rpm
17 lb
SPECIFICATIONS
ACCESSORIES1) 1pc. Bar Socket 3) Metal Case2) Screw Driver (-) 4) Instruction Manual
Model SR121E SR211E SR171E
L 13 5/8 – 15 1/8" 16 5/8 – 18" 11"
L1 6 7/16 – 7 7/8" 9 3/8 – 10 7/8" 6"
L2 2 – 3 7/16" 2 – 3 7/16" 2 1/2"
H 11 1/4" 11 5/8" 10 5/8"
ØD 3 3/8" 4 3/4" 4"
Ød 2 1/2 – 4 1/4" 2 1/2 – 4 1/4" 3 – 3 3/8"
Simple Torqon Electric
9 www.stlouisscrewbolt.com
Code No.
MRUB 34 Z
MRUB 40 Z
MRUB 46 Z
MRUB 52 Z
AF Size
(in)
1 1/16
1 1/4
1 7/16
1 5/8
d
2 3/8
2 3/8
2 1/2
2 3/4
A
3 1/4
3 1/4
3 1/4
3 1/2
L
2
2
2
2 3/8
Bolt Ø
5/8
3/4
7/8
1
Code No.
HRUB 46 Z
HRUB 52 Z
HRUB 58 Z
AF Size
(in)
1 7/16
1 5/8
1 13/16
d
2 3/4
3
3 1/8
A
3 1/4
3 1/2
4
L
2 1/8
2 1/2
2 5/8
Bolt Ø
7/8
1
1 1/8
Code No.
SRUB 58 Z
SRUB 64 Z
AF Size
(in)
1 13/16
2
d
3 3/8
3 1/2
A
4 5/8
5
L
2 1/2
2 1/2
Bolt Ø
1 1/8
1 1/4
Specifications are subject to change without notice
SR31E, SR51E, SR71E
SR121E
SR211E
Code No.
VRU 41 T
VRU 46 T
AF Size
(in)
1 5/8
1 13/16
d
3
3 3/8
A
4 15/16
4 15/16
L
2 1/2
2 1/2
Bolt Ø
1
1 1/8
SR171E
PLEASE NOTE:WHEN USING THESE WRENCHES TO ESTABLISH THE CORRECT TORQUE SETTING THE METHODS RECOM-MENDED BY THE FOLLOWING AGENCIES MUST BE APPLIED.THE RESEARCH COUNCIL ON STRUCTURAL CONNECTIONS, AMERICAN INSTITUTE OF STEEL CONSTRUCTION& INDUSTRIAL FASTENERS INSTITUTE ALL RECOMMEND THE FOLLOWING PROCEDURES.
1. A BOLT TENSION CALIBRATOR WHICH MEASURES DIRECT TENSION.
2. TURN-OF-NUT TIGHTENING.
FOR EXACT DETAILS REFER TO SPECIFICATION FOR STRUCTURAL JOINTS USING ASTM A325 OR A490 BOLTS.STE-5/01
BAR SOCKET
CONSTRUCTION FASTENER MANUFACTURERSSINCE 1887
6900 N. Broadway St. Louis, MO 63147800-237-7059 Fax: 314-389-7510
www.stlouisscrewbolt.com