Stainless Steel, Gas fired Commercial Water Heater

Up to 96% Thermal Efficiency

Up to 5:1 Turndown Ratio

Industry first for Condensing Water Heaters: Top and Side Connection Choices for Inlet and Outlet

Ease of Installation Extremely lightweight tank fits virtually anywhere; 100 gallon: 63” height &80 gallon: 55“ height

316L Stainless Steel Tank Eliminates the need for anode rods

Vents in Inexpensive PVC or CPVC pipe Combined vent lengths up to 200’ in 3” pipe or vent lengths up to 85’ in 2” pipe

Beautiful Stainless Steel Look

80/100 Gallon - 130k /199k Btuh

Inlet / Outlet Connections On Both The Top & Side

This water heater will accommodate even the most difficult installations with lower clearance and multiple inlet and outlet connections making it easier to replace traditional center flue heaters.

Top hot water outlet (stainless steel)

Top cold water inlet (stainless steel)

Tank constructed of 316L stainless steel

Insulated w/ water blown foam

2” thick in the side wall

w/ a rating of R14.2 - 3” thick in the top

w/ a rating of R21.3

Factory installed ASME rated

temperature and pressure

relief valve

Low water cutoff sensor

Lower (cold water)temperature sensor

Upper (hot water) temperature sensor

Side cold water inlet (stainless steel)

Exhaust adaptor to P VC / CPVC / PolyPro venting

Venting Options:- Direct vent side wall- Direct vent vertical- Unbalanced venting- Room air- Combined vent /air intake length up to 200ft

Proprietary heat exchanger: body constructed of 90/10 cupronickel top section constructed of 800H stainless steel

High limit safety sensor

Side hot water outlet (stainless steel)

A Closer Look Inlet / Outlet Connections On Top & Side

L aser Welded Tank An advanced laser allows for more precise welding through a concentrated heat source, producing high quality 316L stainless steel tank construction with stronger, long lasting seams.

Stainless steel burner - 120 volt motor w/

wave modulation control

Condensate trap assembly

Components located on front of heater for

easy service access, all related hardware is made of stainless steel

studs and brass nuts

Digital LED display system monitoring

and temperature adjustment

Why Choose A Stainless Steel Tank?Because They Are Built To Last!

All coated tanks require anodes to delay inevitable corrosion and tank failure. The average commercial water heater lasts about 6 years. The Westinghouse Gas fired Com-mercial Water Heater stain-less steel tank will outlast any coated steel tank in the market.

The Advantages

Eliminates Scale Build-up on HXProlongs Tank Life

No Need for Anode RodsLight Weight Construction

Stainless Steel vs. Glass -Lined

Westinghouse’s 100 GAL. Tank

405 Lbs. (Shipping Weight)

Top Competitor’s 100 GAL. Tank

550 Lbs.

SCALE BUILD-UP

NO Anode Rods Needed!

-Durable Construction

-High Performance

-Excellent Heat Transfer Capabilities

-Self Cleaning

Stainless Steel (1.65mm thick) welded to the top of the heat exchanger where flue gas is the hottest.

Transitions to 90/10 Cupronickel (1.1mm thick) spiral design that expands and contracts rapidly with the change in temperature eliminating scale build-up.

HTP’s Unique Heat Exchanger

G

E F

*ALL DIMENSIONS ARE APPROXIMATE, A SUFFIX OF "LP" DENOTES PROPANE GAS

LP-179-B

PHOENIX MULTI FIT WATER HEATER SPECIFICATION

MODEL* INPUT MODULATIONAIR INTAKE/

EXHAUST VENT SIZE

INLET/OUTLET

SIZE

GASLINE

CONN.

SYSTEMRELIEF

PIPE SIZE

SHIPPINGWEIGHT

MAX.TEMPERATURE

LIMIT

PHM130-80 35,000 - 130,000 2" 1-1/2" 227 GAL

FIRSTHOUR

RATING

314 GAL

238 GAL

329 GAL

PHM199-80 40,000 - 199,000 3" 1-1/2"

PHM130-100 35,000 - 130,000 2" 1-1/2"

PHM199-100 40,000 - 199,000 3" 1-1/2"

08/25/14

PHOENIX MULTI FIT WATER HEATERMODEL* GAL. A B C D E F G H J K L M

PHM130-80/199-80 80 27" 55" 46" 7-1/4" 17" 18-1/4" 8" 3" 46" 38-1/4" 7-1/4" 9-1/2"

PHM130-100/199-100 100 27" 63" 54" 7-1/4" 17" 18-1/4" 8" 3" 54" 38-1/4" 7-1/4" 9-1/2"

L

J

K A

B

D

C

H

M M

285 LBS.

285 LBS.

315 LBS.

315 LBS.

G

E F

*ALL DIMENSIONS ARE APPROXIMATE, A SUFFIX OF "LP" DENOTES PROPANE GAS

LP-179-B

PHOENIX MULTI FIT WATER HEATER SPECIFICATION

MODEL* INPUT MODULATIONAIR INTAKE/

EXHAUST VENT SIZE

INLET/OUTLET

SIZE

AUXILIARYCONN.

GASLINE

CONN.

SYSTEMRELIEF

PIPE SIZE

SHIPPINGWEIGHT

MAX.TEMPERATURE

LIMIT

PHM130-80 35,000 - 130,000 2" 1-1/2" NPT 1" FNPT 3/4" 3/4" 235 LBS 160

PHM199-80 40,000 - 199,000 3" 1-1/2" NPT 1" FNPT 3/4" 3/4" 235 LBS. 160

PHM130-100 35,000 - 130,000 2" 1-1/2" NPT 1" FNPT 3/4" 3/4" 405 LBS. 160

PHM199-100 40,000 - 199,000 3" 1-1/2" NPT 1" FNPT 3/4" 3/4" 405 LBS. 160

08/25/14

PHOENIX MULTI FIT WATER HEATERMODEL* GAL. A B C D E F G H J K L M

PHM130-80/199-80 80 27" 55" 46" 7-1/4" 17" 18-1/4" 8" 3" 46" 38-1/4" 7-1/4" 9-1/2"

PHM130-100/199-100 100 27" 63" 54" 7-1/4" 17" 18-1/4" 8" 3" 54" 38-1/4" 7-1/4" 9-1/2"

L

J

K A

B

D

C

H

M M

Specifications

Stainless Steel, Gas fired Commercial Water Heater

HTP Made In Am

erica • HTP Made In A

mer

ic

a • HTP Made In A

merica • HTP Made In

Am

eric

a •

SCAQMD Rule 1146.2

Stainless Steel, Gas fired, Commercial Water Heater

Model Gal. A B C D E F G H J K L MWGCM080NG130/ WGCM080LP130WGCM080NG199/ WGCM080LP199 80 27” 55” 46” 7 ¼” 17” 18 ¼” 8” 3” 46” 38 ¼” 7 ¼” 9 ½”

WGCM100NG130/ WGCM100LP130WGCM100NG199/ WGCM100LP199 100 27” 63” 54” 7 ¼” 17” 18 ¼” 8” 3” 54” 38 ¼” 7 ¼” 9 ½”

Stainless Steel, Gas fired, Commercial Water Heater

Model Input Modulation Vent Size Inlet/Outlet 1st Hr Rating Gas Line System

Relief PipeShippingWeight

WGCM080NG130/ WGCM080LP130 35,000-130,000 2” 1 ½” NPT 227 Gal. ¾” ¾” 285 Lbs.

WGCM080NG199/ WGCM080LP199 40,000-199,000 3” 1 ½” NPT 314 Gal. ¾” ¾” 285 Lbs.

WGCM100NG130/ WGCM100LP130 35,000-130,000 2” 1 ½” NPT 238 Gal. ¾” ¾” 315 Lbs.

WGCM100NG199/ WGCM100LP199 40,000-199,000 3” 1 ½” NPT 329 Gal. ¾” ¾” 315 Lbs.*All Dimensions are Approximate, LP denotes Propane Gas

, WESTINGHOUSE are trademarks of Westinghouse Electric Corporation. Used under license by HTP, Inc. All Rights Reserved. MKTLIT-XX - 09/ 2016