STANDARD SCHEDULE OF RATES FOR THE YEAR 2020-2021

STANDARD SCHEDULE OF RATESFOR THE YEAR 2020-2021

BLANK

BLANK

BLANK

INDEX

I General Notes 1-12

II Rates for Labour 13-18IIIA Rates for Materials

1 1 PVC Rigid pipes 21

2 1.1 PVC CASING Pipes 223 1.2 UPVC pipes 23

4 1.3 UPVC Column pipe 23

5 1.4 PVC specials 24-256 1.5 PVC specials 26

7 1.6 O-PVC pipes 27

8 2 HDPE pipes 28-309 2.1 HDPE specials 31-32

10 3 A.C. pressure pipes 33

11 3.1 AC Coupler 3412 3.2 CID Joints 35

13 4 CI Spun Pipes 36-3714 4.1 CI D/F Pipes Standard and Non Standard 38

15 4.2 CI D/F Specials & S/S Specials Standard and Non Standard 38

16 5 GI pipes (Medium) 3917 5.1a GI specials 40-42

18 5.1b GI specials 43

19 5.2 GM valves 4420 6 D I S/S K7 pipes 45

21 6.1 D I S/S K9 pipes 46

22 6.2 D I Flanged pipes PN 10 47-5023 6.3 DI specials(All socket) and (All flanged) 51

24 7 House Service Connection for WSS 52-54

25 8 Bar wrapped steel cylinder pipes 55-5826 9 Pipes for UGSS 59

27 10 M.S. Pipes as per IS -3589 spirally/ longitudinal welded 60-62

28 10.1 M.S. Specials 6329 11 RCC non pressure Pipes 64

30 11.1 Rubber gaskets 65

Sl. Category CONTENTS PAGENo. No. NO.


31 12 C.I.D/F sluice valve (PN.1) 6632 12.1 C.I.D/F Reflux valves with ISI marking 6733 12.2 CI Double Air valve with ISI marking 6834 12.3 CI single Air valve with ISI marking 6835 12.4 Kinetic Air valve 6936 12.5 CI Sluice valve PN 1.6 6937 12.6.1 CI Butterfly valve PN 1.6-Wafer Liner 7038 12.6.2 CI Butterfly valve PN 1.6-D/F Gear operated 7039 12.7.1 CI Non-return valve - Wafer type (Dual plate check valve) 7040 12.7.2 CI Non-return valve - Double flanged (Dual plate check) 7141 12.7.3 CI Non-return valve outdoor use 7142 12.8 D.I. Single Chamber Air Release valve 7243 12.9 D.I. D/F Gate valve 7244 12.10 D.I. D/F Butterfly valves 7345 12.11 DI Non return valve 7346 12.12 DI Wafer type Butterfly valve 7447 12.13 DI Disk Check Valve 7548 12.14 DI Diaphragm type flow control Valve 7649 12.14.1 DI Altitude Control valve 7650 12.14.2 DI Pressure reducing valve 7751 12.14.3 DI Flow rate limit control valve 7852 12.14.4 DI Pressure sustaining / Relief valve 7953 12.14.5 DI Pump control valve 8054 12.14.6 DI Pressure reducing and Flow limit control valve 8155 12.14.7 DI Altitude Control and Flow control valve 8256 12.15 DI Plunger type flow control valve 8357 12.16 DI Surge control valve 8458 12.17 OHT flow control valve 8459 13 Salt Glazed Stone Ware pipe of 600MM length 8560 13.1 Salt glazed Stoneware Pipes of 1000MM length with

Rubber Gasket 8561 13.2 Salt glazed Stoneware Pipes of 1200MM length with

Rubber Gasket 8562 14 Sulphate Resistant Cement 8563 15 FRC Frame and Manhole Cover 8664 16.1 Water meter,Dirt box and Strainer and Erection Charges 87

65 16.2 Full Bore Electromagnetic Flowmeter. 87-88


66 17 HDPE Tank 89

67 18 M S Kiosk 89

68 19 MS Ladder. 90

69 20 MS Door , Window, Ventilator 91

70 21.1 Replacement of electrode for Water Disinfection Equipment 92

71 21.2 Electro Chlorinator based on common salt 93

72 22 Fusion Bonded Epoxy coating to Reinforcement Steel Bars 94

73 23 Mechanical joint collars 95

74 24 Stainless steel clamp 96-98

III (B) Rates for Pump Sets

1 1 Centrifugal Monobloc Pumpset without Panel Board 101

2 2 Single phase submersible pumpset without panel board 102

3 3 Three phase submersible pumpset for 100 mm dia bore

without panel board 103

4 3.1. Three phase submersible pumpset for 150 mm dia

Bore without panel board 104-106

5 4 Openwell submersible pumpset without panel board 107-110

6 5 Horizontal Split Casing Centrifugal Pump (1500RPM) 111

7 6 Horizontal Squirrel cage Motor 1500RPM 112

8 7 Horizontal Squirrel cage Motor 1000RPM 113

9 8 Vertical Turbine pump for 1500RPM VHS motor 114

10 9 Vertical Hollow/ Solid Shaft motors for

turbine pump 1500 RPM 115

11 10 Iron Core Oil Cooled Transformer - 11KV/22KV/

11&22KV /433V 116

12 11 Single phase panel board with two level guard and auto start 117

13 11.1 Three phase D.O.L panel board 117

14 11.2 Three phase star delta panel board where

MV panel Board is not used 118

15 11.3 DOL Starter with Single Phasing Preventor 118

16 11.4 FCMA Soft Starter for LT motor 119

17 11.5 FCMA Soft Starter for HT motor 120

18 11.6 Fully Auto Star Delta Starter for installing where

MV panel Board is used 121

19 11.7 Fully Automatic ATS Starter 122


20 12 L.T.Cables (3,3.5,4) Armoured Aluminium conductor cable 123

21 12.1 PVC Insulated and sheathed 3 Core Flat Copper Cables 124

22 12.2 Rate for cable joints including material & labour 125-126

23 12.3 Rate for laying UG Cable below GL and inside pumproom 127

24 12.4 Cable clamps 127

25 12.5 H.T.Aluminium Conductor Cables 128

26 13 Vaccum Pumpset 128

27 14 MCCB 3 Pole & 4 Pole 129

28 15 Capacitor 129

29 16 LT/LTCT Metering Box 130

30 17 Transformer sub station related works 130

31 17.1 ACB 3 Pole & 4 Pole 131

32 18 Safety appliances 131

33 19 Twin CI earthing 132

34 20 Tools 133

35 21 HOT Crane and Accessories 134

36 22 Non Clog Submersible Pumpsets for Sewage applications 135-138

III (C ) Rates for Electro Mechanical items

1 1 Selector switch for Panel Board/Cubical Panel Board/Starter 141

2 2 Multi functions meter-Flush type for M V Panel Board 141

3 3 Ammeter -Digital 141

4 4 Pressure Gauge 141

5 5 Mechanical Interlocking System type for M V Panel Board 142

6 6 Ammeter -Analog 142

7 7 Voltmeter -Digital 142

8 8 Voltmeter -Analog 142

9 9 M V Cubical Panel Board vermi proof box 142

10 10 Electromagnetic contactors 142-143

11 11 Overload relay 143

12 12 Preventor-Single phasing 143

13 13 Preventor-Dry Run 143

III (D) Rates for Building Materials

1 1 Cement 147

2 2 Steel 147


3 1-16 Bricks and Tiles 149-150

4 17 - 54 Stone and Road Materials 150-153

5 55-75 Timber and Roofing Materials 153-154

6 76-82 Metal and Iron Items 154-155

III (E) Rates for Other Construction Materials

1 1-188 Tiles, Polished Stones, Stone Slabs, Aluminium Doors,

Rolling Shutters etc., 159-172

2 189 Cast Iron Nahini / Floor Trap 172

3 190-197 PVC Nahini / Floor Trap etc., 172

4 198-200 Supply & Installtion of Anutone (New Item) 172-174

5 201-225 Polymer Coatip, Termite Proof, Lamination Sheet,

Manhole Cover, PVC Mould CI Steps etc., 174-175

III (F) Water Supply and Sanitary arrangments (Deleted)

III (G) Rates for Electrical Items

I PART-A

1 1 Incandescent Bulbs 230V/ 250V Grade BC/ES 179

2 2 Incandescent Bulb 230V/ 250V Grade BC/ES 179

3 3 PL Lamp (Philips/ Osram) 179

4 4 Fluorescent Tubular Lamps 179

5 5 18w Crystal Glass Led Tube Light 179

6 6 Mercury Vapour Discharge Lamp 230v Grade 3 Pin BC 179

7 7 Box Type Single Fluorescent Fitting With Copper

Choke And Condenser Complete With ISI Mark 179

8 8 Box Type Twin Fluorescent Fitting With

Copper Choke And Condensor [HPF] 180

9 9 Industrial Type Fluorescent Fitting Stove Enamelled

With Copper Choke And Condensor (HPF) 4 Ft. 40w 180

10 10 Decorative Twin Fluorescent Type Fitting With Copper

Choke And Condensor Complete Suitable For 2 Numbers

Fluorescent Tubes 180

11 11 Single Type Street Light Fluorescent Fitting Suitable For

One No. Fluorescent Tube With Copper Choke And Condensor 180

12 12 Twin Type Street Lights Fluorescent Fitting Suitable For

2 Nos. Fluorescent Tubes With Copper Choke And Condensor 180


13 13 Post Top Lantern Fitting Of (Integral Type) With Copper

Choke And Condensor & Necessary Accessories

(Philips/ Crompton Greaves/Wipro)(Spherical / Ribbed /

Conical Acrylic Cover) 180

14 14 CFL Street Light Fittings (Compact Flourescent Lamp) 181

15 15 4ft LED Fitting (New Item) 181

16 16 LED Indoor Fittings (Light Emitting Diode) - Higher End 181

17 17 LED Outdoor Fittings (Light Emitting Diode) - Lower End 182

18 18 LED Outdoor Fittings (Light Emitting Diode) 182

19 19, 20 Timer Switches 63A 4 Pole Contactor 182

20 21 Starters For Fluorescent Tubes 182

21 22 Polyster Filled Copper Choke 182

22 23 Condensor For S.V/ M.V Lamp 183

23 24 Battern type Bakelite holder for lamp 183

24 25 Water tight bulk head fitting 183

25 26 Ceiling Rose 183

26 27 Ceiling fixtures 250/300mm 183

27 28 Ceiling luminaire with mirror optics 183

28 29 Fan clamp (dia 12mm) 183

29 30 Call Bells 183

30 31 Water Heater with ISI Mark 183

II PART ‘B’

31 1 Fans – Confirming to ISS 374 / 1979 184

32 2 Exhaust Fans 184

33 3 Louver shutters arrangements 184

34 4 Ceiling Fan 184

35 5 Dimmer and Regulator 185

III. PART “C”

35 1 Switches 185

36 2 Double Pole Switches 185

37 3 Triple Pole switches (side Handle) 185

38 4 Switch Disconnector fuse units in sheet steel enclosure 186

39 5 Switch Disconnector Fuse Units In Open Execution

(Interior For Cubical) 186

40 6 Fuse units 18641 7 Single Phase DBS 187

42 8 Three Phase DBS 18743 9 Change Over Switches 18744 10 Modular Switches 18745 10.1 Switches 6A - 230V 18746 10.2 Switches 16A - 230V 18847 10.3 Switches 20A - 230V 18848 10.4 Switches 25A - 230V 18849 10.5 Switches 32A - 230V 18850 11 Push Buttons 18851 12 Motor Starter 18852 13 Flush Mounting Boxes (GI) 18853 14 Surface Mounting Boxes (Plastic) 18854 15 Combined Plates (Plastic) 18955 16 Combined Plates (Aluminium) 189

IV PART ‘D’

56 1 Plug and Sockets 19057 2 Single Phase WATT Hour Meters 19058 3 Three Phase WATT Hour Meters 190

V PART ‘E’

59 1 Service Connection Accessories LT. 1100V PVC AluminiumConductor Armoured Under Ground Cable With ISI Mark 190

60 2 PVC Insulated Single Core Multi Strand Fire RetardantFlexible Copper Cable With ISI Mark Conforming ToIS 694/ 1990 191

61 3 Conductor 191

62 4 Cable Glands 19163 5 Fuse Wire(Copper) 19264 6 Neutral Link 15 AMPs 192

VI PART ‘ F ‘

65 1 M.S. Box with Painting (16 SWG) 192VII PART ‘ G ‘

66 1 MS Angles 19267 2 Aluminium Flat 19368 3 Copper Flat 19369 4 Power Capacitor 193

VIII PART ‘ H ‘

70 1 Conduit Materials 16 Gauge 19371 2 Conduit TEE Bends 193


72 3 Conduit Bends 16 Gauge 19373 4 Conduit Inspection Bend 16 Gauge 19374 5 HDPE Pipe 194

IX PART ‘ I ‘

75 1 PVC (Rigid) Pipes (1.8mm Thick) with ISI Mark 19476 2 PVC Rigid Bends 19477 3 PVC Couples 19478 4 PVC TEES 19579 5 PVC Saddles 19580 6 PVC Junction Boxes 19581 7 PVC Hylem sheets 19582 8 Insulation Tape PVC 195

X PART ‘ J ‘

83 1 Teak Wood Materials -T.W. Box concealed type 195XI PART ‘ K ‘

84 1 Crimping Lugs 19685 2 Cable Route Indicator 196

XII PART ‘ L ‘

86 1 Brass Screws 19687 2 Coach Screws 19688 3 Conduit Saddles 19689 4 Sodium Vapour Fittings & Lamp 19790 5 Sodium Vapour Lamp Fitting 19791 6 Miniature Circuit Breakers 19792 7 Plug and Sockets 19893 8 Sheet Steel Enclosure for MCB’s 19894 9 RCCB/ ELCB 19895 10 RCCB/ELCB (Four Pole) 19896 11 HRC Fuses 19997 12 MCB Isolators 19998 13 MCCB 199

XIII PART “M”

99 1 11 KV Indoor Vaccum Circuit Breaker 200100 2 11 KV Outdoor Vaccum Circuit Breaker 200101 3 11 KV Indoor Ring Main Gear (RMG) 200102 4 11 KV Out door Ring main Gear (RMG) 200103 5 HT Cables 200104 6 Cables, Accssories and kits 201


XIV PART “N”

105 1 Supply & Installation of Air-Conditioner with Copper Coil 201106 2 Supply, Installation, Testing, Commissioning and Handing

over of Air- Cooled self contained ductable AC Units 201107 3 Accessories for Package AC 202108 4 Generators with Standard Panel 203109 5 Generators with Auto Main Failure (AMF) Panel 203110 6 Exhaust Pipe with Silencer 204

7 Passenger Lifts (G+3)111 A 8 Persons Passenger Lift Car Size (1300 x 1100) 204112 B 10 Persons Passenger Lift Car Size (1300 x 1350) 204113 C 13 Persons Passenger Lift Car Size (2000 x 1100) 204114 D 20 Persons Passenger Lift Car Size (2000 x 1500) 204

8 Bed - cum - Passenger Lifts (G+3)SS 304 Grade with1m/sec. speed with ARD

115 A 15 Persons Passenger Lift Car Size (1000 x 2400) 205116 B 20 Persons Passenger Lift Car Size (1300 x 2400) 205117 C 26 Persons Passenger Lift Car Size (1600 x 2400) 205

XV PART “O”

118 1 GI Steel tubular pole for street Light 205-207119 2 Octogonal Post 207

3 Lightning Rod120 a Early Streamer Emission Air Terminal (ESEAT). Model: L 208121 b Early Streamer Emission Air Terminal (ESEAT). Model: S 209122 c Mounting Structure 209123 d Down Conductor 209124 e Test Link 209125 f Earth Electrode 210126 g Surge Protection 210

XVI PART “P”

127 1 Conference type Public Address System, Projector andMotorized Screen 210-213

XVII PART “Q”

128 1 Hire charges for Temporary arrangements 213-215XVIII Vertical Three Phase Distribution Board With MCBS

129 1 TPMCB DB With Metal Door Cover With IP 42 Protection 216130 2 TPMCB DB With Acrylic Door Cover With IP 42 Protection 216


129 3 Way vertical TPN Distribution Board 216130 4 Industrial Type TPMCB DB with IP 54 Protection 217

XIX Horizontal Three Phase Distribution Board With MCBS

132 1 TPMCB DB With Metal Door Cover With IP 42 Protection 217133 2 TPMCB DB With Acrylic Door Cover With Ip 42 Protection 217134 3 Industrial Type TPMCB DB With IP 54 Protection 218

XX 7 Segments (3 Tier) 3 Phase Distribution Board With MCB

135 1 Vertical TPN Distribution Board With MCBs(Exceeding100amps) 218

136 2 TPMCB DB With Metal /Acrylic Door Cover With IP 42Protection 218

XXI Single Phase Distribution Board With MCBS

137 1 SPMCB DB With Metal Door Cover With IP 42 Protection 219138 2 SPMCB DB With Acrylic Door Cover With IP 42 Protection 219139 3 Industrial Type TPMCB DB With IP 54 Protection. 219

III (H) Rates for Conveyance of Materials

1 1 Rates for Conveyance of C.I. / G.I / D.I pipes and specials 2232 2 Rates for Conveyance of M.S. pipes and specials 2243 3 Rates for Conveyance of R.C.C. / P.S.C / B.W.S.C

pipes and specials 2254 4 Rates for Conveyance of A.C. pipes and specials 2265 5 Rates for Conveyance of PVC / HDPE /

GRP pipes and specials 2276 6 Rates for Conveyance of SW pipes and specials 2287 7 Rates for Conveyance of Pig lead and Yarn 2298 8 a Rates for Conveyance of Materials by Road in Hills 2309 8 b Rates for Conveyance of Materials by Road in Plains 23110 9 Rates for Conveyance of Materials by Head load 232

IV (A) Rates for Works

1 1-4a Infiltration Works 235-2412 5a - 14f Pipe Laying Works 241-2603 15 a. Slow Sand Rapid Sand Filter Works 2604 16 Drainage Works 2615 17 HDPE Jointing 2616 18 Jointing of Mechanical joint collars 2627 19 Disjointing of GI pipes 2628 20 Welding of GI pipes. 2629 Data Illustrations 263


IV (B) Rates for Earthwork Excavation other than pipe

laying works and open wells

1 1-18 Earth Excavation other than pipe laying works and open wells 267-2682 19 a) Refilling with excavated sand 2683 19 b) Refilling with excavated soil (other than sand) 2684 20 Quarrying and Blasting 268

IV (C ) Rates for earthwork excavation for pipe laying

works for water Supply and Sewerage works

1 I Earthwork excavation in 273a) Sand, silt or other loose soil -SS 20B 273b) Hard stiff clay,Stiff black Cotton etc.,-SS 20B 273

2 II a) In Soft Disintegrated rock etc., not requiring blasting 273b) In Dense Medium rock not requiring blasting 273c) In Dense Medium rock requiring blasting 273d) In Hard Rock including blasting 273

3 III a) Earth work excavation control basting - in DMR 273 b) Earth work excavation control basting - in HR 274

IV (D) Rates for earthwork excavation and refilling for

pipe line works having base width 1.25m & below on

linear Measurement Basis

1 1 Earthwork excavation and Refilling for pipe line works havingbase width 1.25m & below on Linear Measurement Basis. 277-279

IV (E) Rates for Miscellaneous works

1 1-7. Plumbing 283-2842 8-21. Drilling works 284-2953 22 Surveying and Levelling by Total Station Method 2964 23 Dismantling 296-2995 24 Open well excavation 299-3006 25 Rate for work by Deploying Machineries 3017 26 Lift charges - concrete - Brick or stone

Masonry above or below ground level 301-3038 27 Concrete Vibrators 3039 28 plastering 30310 29 White Washing and Colour wasing and distempering 30411 30 Painting, Wood oiling, Tarring, Vanishing , Bee’s Waxing etc 30412 31 Miscellaneous 30413 32 River Conservancy of Korambu Works 304


14 33 Labour Wrought and put up for Doors , Windows and

Ventilators 305-30615 34 Breaking Metals 307

16 35 Cement Mortar 307

17 36 Metal & Iron Works 30718 37 Conveyance of excavated earth from the narrow street

(width less than 3.75m) 307

19 38 Re-Conveyance of earth from the stock yard to the narrowstreet (width less than 3.75m) for refilling the trenches 307

20 39 Disposal of surplus earth including loading and conveyance

within a distance of 5 km 30721 40 Lighting arrangements (maintenance works) with genset: 307

22 41 Hire charges for deploying earth moving machinery

(JCB/Poclain) for earthwork 30823 42 Supply and delivery of Natural Pebbles filter media 308

24 43 Barricading for pipeline works for the WSS / UGSS works 309

25 44 Shoring and Strutting for the WSS / UGSS works 31026 45 Trenchless Technology for pipe laying work in

Railway/NHAI/SH/NH crossings. 311-313

27 46 Replacement of under ground utilities (HSC pipes,distribution system & pumping main pipes, etc.) 314-317


1

I. GENERAL NOTES

2

.

3

I. GENERAL NOTES

1. For items not covered in the schedule of rates, the Superintending Engineercan fix the rates based on the lowest sealed quotations duly observing all thedepartmental formalities under intimation to the concerned Chief Engineerand Head Office.

2. For special nature of works, for which rates are not covered in the Scheduleof Rates separate schedule of rates issued by the respective Officers /Department / Board are to be followed.

3. Extra percentage other than those for the specified areas noted below, shallnot be allowed.

1. Corporation Limits.

An extra 10% on the Rates of Labour, Rates of Works and for Head Loadshall be allowed for the works in Erstwhile Chennai Corporation limit and thebelt area of 32 km around erstwhile Chennai Corporation limits (i.e) prior toformation of Greater Chennai Corporation, Madurai Corporation limits,Coimbatore Corporation limits and also for works in Hosur Taluk.

2. An extra 5% on the Rates of Labour, Rates of Works and for Head Loadshall be allowed for the works in Trichy, Salem, Tirunelveli, Tiruppur, Erode,Thoothukudi and Vellore Corporation limits.

3. Restricted areas:

I. An extra 10% on the Rates of Labour and Rates of Works shall beallowed for sewer works under unhygienic condition.

II. An extra 10% on the Rates of Labour, Rates of Works and Conveyancecharges shall be allowed for works in the campus of Central Jails.

III. An extra 5% on the Rates of Labour, Rates of Works and Conveyancecharges shall be allowed for works in the campus of Sub-Jails.

IV. An extra 20% on the Rates of Labour, Rates of Materials, Rates ofWorks, Conveyance Charges and Head Load shall be allowed for worksin Reserve Forest Areas.

4. Special Nature of Works

I. i. 5 times over the basic rates for earthwork excavation for bothrural and urban areas is allowed for putting trial pits.

ii. 5 times over the basic rates for earthwork excavation for leakrectification works is allowed.

iii. If the works are done (leak rectification works) in odd hours(i.e) 8.00PM to 8.00AM of the next day, 7.50 times over thebasic rate is allowed.

4

II. For individual footings of the service reservoirs, valve pits, Manholesin UGSS double the relevant rate for earthwork excavation is allowed.

III. An extra 5% is allowed for laying of sewers under UGSS for earthworkexcavation alone below 4m depth.

5. For Works in Hills:

As the transport facilities in most of the Hilly Areas are now considerablyimproved and as there is no necessity for allowing extra percentage as hithertofollowed, the Hilly Areas are now again regrouped as detailed hereunder andthe extra percentage allowable has been revised accordingly and fixed.

The conveyance table approved and furnished in the Schedule of Rates underthe Head “Conveyance table”, Conveyance of materials by Road on hillsshall be adopted for all works in hills.

i. For works in Nilgiris District an extra 40% on the rates of labour,rates of work, head load and an extra 25 % on the rates of materialsshall be allowed.

ii. For works in Mudumalai Sanctuary, Shandy Nallah Sheep Farm,Dansandle areas, an extra 40% over rates of labour, rates of workand head load and an extra 25% on the rates of materials shall beallowed.

iii. For works in Valparai Area an extra 40% on the rates of labour,rates of work, head load and an extra 25% on the rates of materialsshall be allowed.

iv. For works in Gudiyalathur, Siruvani, Thavalamalai Hills, TalavadiHills, Bargur Hills, Anamalai, Chennimalai and Sivanmalai Hills anextra 20% on the Rates of Labour, Rates of Materials, Rates of Worksand Head Load shall be allowed.

v. For works in Western Ghats of Madurai, Virudhunagar, Coimbatore,Tirunelveli & Kanyakumari Districts an extra 20% on the Rates of Labour,Rates of Materials, Rates of Works and Head Load shall be allowed.

vi. (a) An Extra 50% on the Rates of Labour for works in Thekkady shallbe allowed.

(b) Add 25% extra shall be allowable on the Rates of Materials whichare to be supplied at Thekkady, subject to the condition that thereshall not be any extra on conveyance, tollgate fee, interstateallowance, etc. The conveyance charge as applicable for Ghat Road,Cart Track, etc., as per schedule of rates is only applicable.

5

vii. An extra 60% shall be allowable on the Rates of Materials to be suppliedfor Periyar Dam Site subject to the condition that there shall not be anyextra on conveyance, tollgate fee, interstate allowance, etc. Theconveyance charge as applicable for Ghat Road, Cart Track, etc., as perSchedule of Rates is only applicable.

viii. An extra 100% on the Rates of Labour for works in Periyar DamSite under normal condition shall be allowed.

ix. An extra 150% on the Rates of Labour for works in Periyar DamSite under hanging condition shall be allowed.

x. An extra 50% on the Rates of Labour, Rates of Materials, Ratesof Works and Head Load shall be allowed for the works at LowerCamp above Kuruvanthu Bridge, Bodi Hills, Cumbam mettu,Sirumalai, Pachai Kamatchi Hills, Palani Hills, Thiruparankundram Hills,Idumban Hills, Megamalai Panchayat and Thummakundu Panchayat.

xi. An extra 40% on the Rates of Labour, Rates of Works and HeadLoad and an extra 25% over the rates of materials shall be allowedfor the works at Kodaikanal.

xii. An extra 25% on the Rates of Labour, Rates of Materials, Ratesof Works and Head Load shall be allowed for works in Yercaud,Yercaud Sub-Taluk, Boothamalai, Aranuthumalai, Sarugumalai andThiruchengode Hills in Salem & Namakkal District.

xiii. An extra 40% on the Rates of Labour, Rates of Works and HeadLoad and an extra 25% over the Rates of Materials shall be allowedfor works in Kalrayan Hills, Pachamalai Hills and Kolli Hills in Salem &Namakkal Districts.

xiv. An extra 40% on the Rates of Labour, Rates of Works and HeadLoad and an extra 25% over the Rates of Materials shall be allowedfor works in Jawadhu Hills, Elagiri Hills, Kalrayan Hills, NakkanamalaiHills, Naickerneri Hills in Thiruvannamalai and Vellore Districts.

xv. An extra 40% on the Rates of Labour, Rates of works and HeadLoad and an extra 25% over the Rates of Materials shall be allowedfor works in Piranmalai covering Oduvarpatti, Kattugudipatti,Ponnadaipattu, V.Pudur Village, Mamalai covering Vannar Irruppu,Nagamangalam Villages, Usilamalai covering Poolankurichi Village,Hillocks at Musundapatti, Usilam, Ammapatti and Thuthampatti inSivagangai District.

xvi. An extra 40% on the Rates of Labour, Rates of Works and HeadLoad and an extra 25% over the Rates of Materials shall be allowed

6

for works in Chitteri Hills, Sittiling in Kalrayan Hills in DharmapuriDistrict.

xvii. An extra 40% on the Rates of Labour, Rates of Works and HeadLoad and an extra 25% over the Rates of Materials shall be allowedfor works in Kalrayan Hills in Cuddalore and Villupuram Districts.

xviii. An extra 40% on the Rates of Labour, Rates of Works and HeadLoad and an extra 25% over the Rates of Materials shall be allowedfor works in Pachamalai Hills in Trichy, Karur and Perambalur Districts.

Note: Since the studies for allowing extra percentage for hilly areas was workedout in the year 2002-2003, the Committee decided that the same hasto be revised or modified by constituting a separate Committee to takea decision on revision, based on the latest transport facilities,infrastructural facilities etc., available in the hilly areas for the issue ofSchedule of Rates from the next year 2020–2021 onwards.

6. ISLANDS in Ramanathapuram District:

a. For works in Rameswaram Island:

An extra 25% on the Rates of Labour, Rates of Works and Head Loadshall be allowed.

b. For works in Other Islands:

An extra 125% on the Rates of Labour, Rates of Materials, Rates ofWorks, Conveyance Charges and Head Load shall be allowed for otherIslands in Ramanathapuram viz., (1) Upputhannie Island, (2) PuleevilaichalliIsland, (3) Aalaippar Island, (4) Valimunai Island, (5) Appa Island,(6) Thalaiyari Island, (7) Valai Island, (8) Mullai Island, (9) Manoli Island(10) Minoliputti Island, (11) Nadu Island, (12) Nallathannie Island, (13)Pullivasal Island, 14) Poomarichan Island, (15) Muyal Island, (16) SingalaIsland and (17) Kurusedar Island.

c. For works in Islands of Thoothukudi District :

An extra 125% on the Rates of Labour, Rates of Materials, Rates ofWorks, Conveyance Charges and Head Load shall be allowed for Van,Kasuvar, Karaichalli Island and Vilankuchali Islands.

7. TUNNELS:

An extra 15% on the Rates of Labour and Rates of Works shall be allowedfor works inside Tunnels.

7

8. DAM SITES UNDER HANGING CONDITION (Other than Periyar DamSite)

An extra 75% on the Rates of Labour employed for the items of works,which may have to be executed by hanging from the top of Dam throughslings (or) rope ladders to work in dizzy height. (This will apply only formaintenance and repair works).

9. General Foot Note:

i) The rates of labour means the labour rates fixed under the head, Rates ofLabour.

ii) Rates of works includes the labour for earthwork, refilling foundation,dismantling, jungle clearance, head load etc., also where human labour aloneis involved.

iii) The percentage increase provided for the materials are applicable only forthe materials which are quarried or manufactured locally in the specifiedarea.

iv) The percentage increase provided for Rates of Works are allowable only onthe items where human labour alone is involved.

v) The percentage increase provided for Conveyance Charges are allowablefor the distance covered in the specified area / Special Tract only.

vi) The extra percentage allowable as specified above shall not be applicable forthe materials / works covered under “Rates of other construction materials”and “Rates of Electrical items of works”. Similarly, no conveyance chargesshall be allowed for the items covered under these two categories. The ratesapproved therein are applicable at site of work.

vii) While adopting source of any materials inside the special tracts viz., Corporationlimits, Reserve Forest Areas, Hilly areas, Islands, Dam Sites etc., where extrapercentage allowable for the materials which are quarried or manufacturedlocally, it is the duty of the officer in charge of the work (not below the rank ofAssistant Executive Engineer), to analyse and confirm whether the finishedcost of such materials/ works are higher if the materials are conveyed andbrought to the site from the areas outside the specified area, where suchextra percentage are not permissible.

viii) As per Notification No.31/2017- Central Tax(Rate) dated 13th October, 2O17the concessional rate of GST at 12 % [CGST at 6% + SGST at 6% ] isleviable for any Government contract, whether Civil or Electrical, irrespectiveof the GST rate applicable on purchase of goods used in the execution ofGovernment Contract. The contractor is eligible to get refund of excess tax

8

paid over or liable to pay tax as per Notification No.20/2017, Central Tax(Rate) dated 22.8.2017, Notification No.24/2017, Central Tax (Rate) dated21.9.2017 and Notification No.31/2017, Central Tax (Rate) dated 13.10.2017.

ix) Further, for Works Contract services involving predominantly earth works(that is, constituting more than 75 % of the value of the works contract)supplied to Central Government, State Governments, Local Authority,Governmental Authority for Government Entity shall be taxed at 5 % as perNotification No.31/2017 - Central Tax (Rate) dated 13th October, 2017.Therefore, for such contract the amount of GST is to be calculated at 5 %[CGST at 2.5 % + SGST at 2.5 %) over and above the Basic rate.

10. LEAD

i. District-wise average lead may be approved by the concernedChief Engineers based on the approved quarry by the PWD for CWSS.

ii. Lead for respective local body such as Town Panchayats, Municipalities,and Corporation may be adopted separately for the stand alone watersupply schemes/ UGSS.

9

1 For works in Erstwhile ChennaiCorporation limits and the beltarea of 32 KM around erstwhileChennai Corporation limits (i,e)prior to formation of GreaterChennai Corporation, MaduraiCorporation limits, CoimbatoreCorporation limits and also forworks in Hosur Taluk.

2. For works in Trichy, Salem,Tirunelveli, Tiruppur, Erode,Thoothukudi and VelloreCorporation limits.

3. Restricted Areas

i For Sewer works underunhygienic condition

ii For works in Central jail Campus

iii For works in Sub Jail Campus

iv For works in Reserve ForestAreas

4 Hills

i For works in Nilgiris District

ii For works at MudumalaiSanctuary, Shandy Nalla SheepFarm, Dansandle Area

iii For works at Valparai

iv For works at Gudiyalathur,Siruvani, Thavalamalai Hills,Thalavadi Hills, Bargur Hills,Anamalai, Chennimalai andSivanmalai Hills

v For works in Western Ghatsof Madurai, Virudhunagar,Coimbatore, Tirunelveli andKanyakumari Districts.

10% — 10% — 10%

5% — 5% - 5%

10% — 10% — —

10% — 10% 10% —

5% — 5% 5% —

20% 20% 20% 20% 20%

40% 25% 40% — 40%

40% 25% 40% — 40%

40% 25% 40% — 40%

20% 20% 20% — 20%

20% 20% 20% — 20%

STATEMENT SHOWING THE EXTRA PERCENTAGE ALLOWABLE AS PERGENERAL NOTE TO SCHEDULE OF RATES FOR THE YEAR 2020-2021

(with effect from 01-07-2020)

Labour Material

Rate of work(where

human labourinvolved)

Conveyance HeadLoad

PERCENTAGE EXTRA ALLOWABLE ONSl.No. Area

10

Sl.No. Area Labour Material

Rate of work(where


Conveyance HeadLoad

PERCENTAGE EXTRA ALLOWABLE ON

In Madurai, Theni & DindigulDistricts.

vi For works at Thekkady

vii For works at Periyar Dam Site

viii For works at Periyar Dam Siteunder normal condition

ix For works at Periyar Dam Siteunder hanging condition

x For works at Lower Camp aboveKuruvanthu Bridge, Bodi Hills,Cumbum Mettu, Sirumalai,Pachai Kamatchi Hills, Palani Hills,Tiruparankundram Hills,Idumban Hills, MegamalaiPanchayat and ThummakunduPanchayat

xi For works at Kodaikanal

xii For works at Yercaud Hills,Yercaud Sub - Taluk,Boothamalai, Aranuthumalai,Sarugumalai and TiruchengoduHills in Salem & NamakkalDistricts.

xiii For works at Kalrayan Hills,Pachamalai Hills, Kolli Hills inSalem and Namakkal Districts.

xiv For works at Jawadhu Hills,Elagiri Hills, Kalrayan Hills,Nakkanamalai Hills, NaickenneriHills in Thiruvannamalai andVellore Districts.

xv For works at Piranmalai coveringOduvarpatti, Kattugudipatti,Pannadaipattu, V.Pudur Villages,Mamalai covering Vannar Iruppu,Nagamangalam Villages,Usilamalai covering PoolankurichiVillage, Hillocks at Musundapatti,Usilam, Ammapatty andThuthampatti in SivagangaiDistrict.

50% 25% — — —

— 60% — — —

100% — — — —

150% — — — —

50% 50% 50% — 50%

40% 25% 40% — 40%

25% 25% 25% — 25%

40% 25% 40% — 40%

40% 25% 40% — 40%

40% 25% 40% — 40%

11

Sl.No. Area Labour Material

Rate of work(where


Conveyance HeadLoad

PERCENTAGE EXTRA ALLOWABLE ON

xvi For works at Chitheri Hills,Sittiling in Kalrayan Hills inDharmapuri District.

xvii For works at Kalrayan Hills inCuddalore and VillupuramDistricts.

xviii For works at Pachamalai Hills inTrichy, Karur and PerambalurDistricts.

5 ISLANDS

I For works at Rameswaram Islandin Ramanathapuram District.

ii For works in other Islands viz.,Upputhannie, Puleevilaichalli,Alaiappar, Valimunai, Appa,Thalaiyari, Valai, Mullai, Manoli,Minidiputti, Nadu, Nallathannie,Pullivasal, Poomarichan, Muyal,Singala, Kuruseedar Islands inRamanathapuram District.

iii For works in Van, Kasuvar,Karaichalli and VilankurichiIslands in Thoothukudi District.

6 TUNNELS

i Where human labour alone isinvolved

7 DAM SITES UNDER HANGINGCONDITION

i. For works at dam sites otherthan Periyar Dam Site, whichmay be executed by hangingfrom top of dam through slingsor rope ladders to work in dizzyheight.

40% 25% 40% — 40%

40% 25% 40% - 40%

40% 25% 40% — 40%

25% - 25% - 25%

125% 125% 125% 125% 125%

125% 125% 125% 125% 125%

15% - 15% - -

75% - - - -

12

.

II. RATES FOR LABOUR

14

.

15

TWAD BOARDII. RATES FOR LABOUR

Schedule Rate for

Item No. Description Unit 2020-21in Rupees

1 Driller Day 714.002 Assistant Driller Day 586.003 Special heavy labour for driving sheet pile Day 714.004 Boring Attendant Day 521.005 Water Meter Reader Day 498.006 Helper for Rig Day 521.007 a. Electrician with LEE/DEE and ‘C’ certificate Day Deleted

b. Electrician with LEE/ DEE Day DeletedC. Electrician with ITI and ‘C’ Certificate Day Deletedd. Electrician with ITI ‘and B’ Certificate Day Deletede. Electrician with ITI Day Deleted

8 a. Pump Operator with ITI Day Deletedb. Pump Operator without ITI Day Deleted

9 Laboratory Attender SSLC/ 10th Std passed Day 422.0010 a. Filter Bed Operator with D.M.E. Day 874.00

b. Filter Bed Operator with ITI Day 714.00c. Filter Bed operator without I.T.I. Day 608.00

11 Cleaner for Treatment Unit, Pump and vehicles Day 498.0012 Boring Mechanic for Hand Boring set Day 608.0013 Turn Cock (Experience in pipe line

Operationand maintenance) Day 498.0014 Fitter (Pipe laying / Bar bending) I Class Day 667.0015 Fitter (Pipe laying / Bar bending) II Class Day 647.0016 Sewer Cleaner Day 498.0017 Store Attender SSLC /10th Std Passed Day 498.0018 Divers and Well Sinkers Day 683.0019 Hammer Man (Geophysical survey) Day 473.0020 Geological Assistant Day 730.0021 Maintenance Assistant Day 521.0022 Plant Operator, SSLC passed with 3 years experience Day 585.0023 Reverse Osmosis (R.O.) Plant Operator SSLC passed with

3 years experience Day 714.0024 Mechanic with ITI Day 587.0025 a. Carpenter I Class Day 752.00

b. Carpenter II Class Day 718.0026 a. Cleaner I Gr. Day 400.00

b. Cleaner II Gr. Day 396.0027 a. Fitter I Class Day 679.00

b. Fitter II Class Day 660.00

16

28 Floor Polisher Day 592.0029 Gardener Day 469.0030 Head Mazdoor for Well sinking Day 497.0031 a. Driver (Light duty) Day 592.00

b. Driver (Heavy duty) Day 633.0032 Jumper Mazdoor Day 469.0033 a. Maistry, Road Inspector & Work Inspector Day 571.00

b. Maistry, Road Inspector & Work Inspector(Degree holder) Day 633.00

34 a. Mason for Brick Work - I Class Day 769.00b. Mason for Brick Work - II Class Day 718.00

35 a. Mason for Stone Work - I Class Day 769.00b. Mason for Stone Work - II Class Day 718.00

36 a. Mazdoor Category I Day 502.00b. Mazdoor Category II Day 412.00c. Head Mazdoor Day 519.00

37 a. Moplah - I Class Day 591.00a. Moplah - II Class Day 569.00

38 a. Painter/Varnisher-I Class Day 615.00b. Painter/Varnisher-II Class Day 595.00

39 Pile Driver Day 546.0040 a. Plumber I Class Day 667.00

b. Plumber II Class Day 647.0041 Pump Driver Day 519.0042 a. Stone cutter- I Class Day 591.00

b. Stone cutter- II Class Day 569.0043 a. Welder/ Bracer - I Class Day 591.00

b. Welder/ Bracer - II Class Day 569.0044 Well sinking Diver working with Helmet

(above two metres depth of water) Day 689.00Technical Assistant

45 a. Technical Assistant Gr.I (BE passed) Day 937.00b. Technical Assistant- Gr.II (Diploma in Engg. Passed/

B.E. failed/ Degree in Geology for ground water works) Day 844.00c. Technical Assistant Gr.III (Diploma in Engg. Failed /

ITI (Civil) passed Day 714.0046 a. Laboratory Assistant. Gr.I (Post Graduate in Science) Day 714.00

b. Laboratory Assistant. Gr.II (Degree in Science/Degree in Geology for ground water) Day 654.00

c. Laboratory Assistant Grade III (with Degreequalification to work as works clerk) Day 589.00

47 a. Mazdoor employed for Geological maping Day 502.00

Schedule Rate for


17

b. Mazdoor employed for Pitting, Trenching, Samplingand Drilling works Day 502.00

c. Mazdoor employed for Geophysical Investigation works Day 502.00d. Head Mazdoor to supervise exploratory works Day 531.00

48 Mixer Operator (including concrete mixer ) Day 546.0049 Mixer Driver Day 519.0050 Compressor Operator Day 522.0051 Computer Operator

a. Gr.I [B.E. (Computer Science)/M.Sc., (Computer Science)] Day 937.00

b. Gr.II [B.Sc., (Computer Science)/Diploma in Computer Science] Day 844.00

52 Stone & Crusher Operator Day 522.0053 Heavy Mazdoor Day 546.0054 Wireman Grade I/ Electrician Grade I Day 636.0055 Wireman Grade II/ Electrician Grade II Day 633.0056 Electrical Helper Day 497.0057 Laboratory Attendant Day 425.0058 Electrical Maistry Day 730.0059 Axe Mazdoor Day 469.0060 Blacksmith - 1st Class Day 592.0061 Blacksmith - 2nd Class Day 569.0062 Boat Mazdoor Day 497.0063 Bullocks pair with driver (with bandy) Day 928.0064 Bullocks single with driver (with bandy) Day 667.0065 Caulker Day 519.0066 Ferry Mazdoor Day 519.0067 Hammer Mazdoor Day 476.0068 Mechanic - 1st Class Day 592.0069 Mechanic - 2nd Class Day 569.0070 Navagonies or Javali Man - 1st Class Day 497.0071 Sawyer Day 546.0072 Smith 1st Class Day 591.0073 Smith 2nd Class Day 569.0074 Sprayer Mazdoor (for bitumen, tar etc.,) Day 469.0075 Syrang-1st Class Day 591.0076 Syrang-2nd Class Day 569.0077 Thatcher Day 497.0078 Tinker 1st Class Day 476.0079 Tinker 2nd Class Day 469.0080 Turner 1st Class Day 546.0081 Turner 2nd Class Day 519.00

Schedule Rate for


18

82 Time Keeper Ist Class Day 591.0083 Time Keeper 2nd Class Day 569.0084 Well Diver for removing silt - 1 st Class Day 591.0085 Well Diver for removing silt - 2nd Class Day 569.0086 Well sinker - 1st Class Day 667.0087 Well sinker - 2nd Class Day 647.0088 Wodder Day 497.0089 Cinema Operator (ITI Passed) Day 589.0090 B.Sc., (Agriculture) Passed- Technical Assistant Day 844.0091 Irrigation Community Organiser Grade I [B.E(Agri) passed/

B.Sc.,(Agri)Passed/PG (Geology) & Rural Development] Day 903.0092 Irrigation Community Organiser Grade II [B.E(Agri) failed/

B.Sc.,(Agri)failed /Diploma in Agri. Passed)] Day 752.0093 HeatMaster Operator Day 497.0094 Raker Day 519.0095 Lift Operator Day 571.0096 Sound Service Operator Day 476.00

Schedule Rate for


III (A) RATES FOR MATERIALS

20

.

21

1.0 UN PLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLYAS PER IS 4985 / 2000

Sl. Description UnitRate for 2020-21 in Rupees

NoI Quarter II Quarter III Quarter IV Quarter

I 4KSC

1 63mm Metre 50.002 75mm Metre 69.003 90mm Metre 95.004 110mm Metre 134.505 140mm Metre 224.006 160mm Metre 290.007 180mm Metre 376.008 200mm Metre 451.00II 6KSC

1 50mm Metre 44.002 63mm Metre 70.003 75mm Metre 96.004 90mm Metre 135.005 110mm Metre 188.006 140mm Metre 325.007 160mm Metre 412.008 180mm Metre 532.009 200mm Metre 660.00

III 10KSC

1 50mm Metre 69.002 63mm Metre 105.003 75mm Metre 146.504 90mm Metre 211.005 110mm Metre 317.006 140mm Metre 517.007 160mm Metre 652.008 180mm Metre 840.009 200mm Metre 1035.00

Note : 1) The above rates are basic rates inclusive of transportation charges to stockyardanywhere in Tamilnadu.

2) Unloading, stacking at stock yard and Conveyance from stock yard to siteare extra.

3) GST extra applicable as per GO

22

1.1 PVC CASING PIPE AS PER IS 12818 / 2010


No I Quarter II Quarter III Quarter IV Quarter

1 150mm CS Metre 442.00

2 150mm CM Metre 576.00

3 150mm RS Metre 722.00

4 200mm CS Metre 825.00

5 200mm CM Metre 1061.00

6 200mm RS Metre 1247.00


2) Unloading, stacking at stock yard and Conveyance from stock yard to site areextra.


CS - Casing Shallow depth up to 80mCM - Casing Medium depth 81m to 250mRS - Ribbed screen pipe

23

1.2 UN PLASTICIZED NON - PRESSURE POLYVINYL CHLORIDE (PVC-U)PIPES FOR USE IN UNDERGROUND DRAINAGE AND SEWERAGE

SYSTEMS AS PER IS 15328/2003

Sl. Description Unit Rate for 2020- 21 in RupeesNo.

I SN8-SDR 34(S 16.5)1 110mm Per Metre 201.002 125mm Per Metre 263.003 160mm Per Metre 422.004 200mm Per Metre 658.005 250mm Per Metre 1021.006 315mm Per Metre 1637.00II SN4-SDR 41(S 20)1 125mm Per Metre 225.002 160mm Per Metre 342.003 200mm Per Metre 544.004 250mm Per Metre 852.005 315mm Per Metre 1317.00

III SN2-SDR 51(S 25)1 160mm Per Metre 291.002 200mm Per Metre 449.003 250mm Per Metre 695.004 315mm Per Metre 1113.00

Note : 1) The above rates are basic rates inclusive of transportation charges tostockyard anywhere in Tamilnadu.



1.3 UPVC- Column Pipe

Sl.No. Description Unit Rate for 2020 -21 in Rupees

1 25mm Per Metre 72.00









24

1.4 PVC SPECIALS AS PER IS 7834/1987


PVC THREADED COUPLER

1 63 mm x 50 mm Each 42.002 75 mm x 50 mm Each 65.003 90 mm x 80 mm Each 82.004 110 mm x 100 mm Each 147.005 140 mm x 125 mm Each 205.00

UNEQUAL TEE

1 63 mm x 50 mm Each 32.002 75 mm X 50 mm Each 39.003 90 mm x 50 mm Each 93.004 90 mm x 63 mm Each 87.005 90 mm x 75 mm Each 92.006 110 mm x 50 mm Each 81.007 110mm x 63 mm Each 82.008 110 mm x 90mm Each 164.009 140mm x 50 mm Each 332.0010 140 mm x 63 mm Each 300.0011 140 mm x 90 mm Each 312.0012 140 mm x 110 mm Each 265.0013 160 mm x 50 mm Each 472.0014 160 mm x 63 mm Each 460.0015 160 mm x 90 mm Each 218.0016 160 mm x 110mm Each 250.0017 160 mm x140 mm Each 627.00

PVC REDUCER COUPLER

1 63 mm x 50 mm Each 15.002 75 mm x 63 mm Each 12.003 90 mm x 63 mm Each 24.004 90 mm x 75 mm Each 19.005 110 mm x 63 mm Each 35.006 110 mm x 75 mm Each 40.007 110 mm x 90 mm Each 30.008 140 mm x 63 mm Each 108.009 140 mm x 90 mm Each 77.0010 140 mm x 110 mm Each 48.0011 160 mm x 110 mm Each 108.0012 160 mm x 140 mm Each 89.00

25

PVC REDUCER MULTI STAGE


PVC REDUCER FABRICATED


SADDLE PIECE

1 63 mm x 20 mm Each 51.002 75 mm x 20 mm Each 59.003 90 mm x 20 mm Each 68.004 110 mm x 20 mm Each 79.005 140 mm x 20 mm Each 99.006 160 mm x 20 mm Each 113.00




26

1.5

P

VC

SP

EC

IALS

AS

PE

R I

S 1

01

24

/1

98

2 P

art

-II

co

nt.

.

Sl.

Rat

e fo

r 2

02

0 -

21

i

n

Ru

pee

s

No.

Des

crip

tion

20

mm

25

mm

32

mm

40

mm

50

mm

63

mm

75

mm

90

mm

11

0m

m1

40

mm

16

0m

m2

00

mm

1PV

C C

oupl

ers

fabr

icat

ed 4

KS

C-

--

-6.

008.

0012

.00

19.0

030

.00

55.0

086

.00

182.

00

2PV

C C

oupl

ers

fabr

icat

ed 6

KS

C-

--

-6.

0013

.00

19.0

030

.00

46.0

080

.00

128.

0026

5.00

3PV

C B

ends

fab

rica

ted

4 K

SC

--

--

19.0

024

.00

40.0

060

.00

102.

0025

3.00

346.

0066

6.00

4PV

C B

ends

fab

rica

ted

6 K

SC

--

--

19.0

037

.00

62.0

094

.00

160.

0036

6.00

510.

0098

9.00

5PV

C E

qual

Tee

Fab

rica

ted

4 K

SC

--

--

34.0

050

.00

54.0

012

1.00

173.

0028

7.00

362.

0044

8.00

6PV

C E

qual

Tee

Fab

rica

ted

BIS

101

24/1

982

Part

V 6

KSC

--

--

36.0

061

.00

88.0

013

3.00

237.

0042

1.00

464.

0056

8.00

7PV

C C

oupl

ers

(Mou

ld)

BIS

783

4/19

75 P

art

VI

3.00

3.00

5.00

5.00

9.00

20.0

031

.00

46.0

071

.00

199.

0024

4.00

458.

00

8PV

C E

lbow

(M

ould

)

BIS

783

4/19

75 P

art

VI

3.00

5.00

9.00

13.0

026

.00

44.0

066

.00

94.0

016

4.00

154.

0025

0.00

579.

00

9PV

C E

qual

tee

(M

ould

)

BIS

783

4/19

755.

007.

0011

.00

19.0

031

.00

56.0

078

.00

128.

0019

9.00

231.

0033

9.00

1008

.00

10PV

C M

ale

Thre

aded

Ado

pter

--

--

15.0

020

.00

41.0

056

.00

80.0

012

5.00

221.

0031

9.00

11PV

C E

nd C

ap2.

003.

005.

007.

0010

.00

16.0

019

.00

29.0

050

.00

72.0

097

.00

287.

00

12PV

C T

ail

piec

e w

itho

ut

flang

e

(BIS

mar

ks)

--

--

35.0

024

.00

37.0

058

.00

93.0

017

2.00

253.

0035

2.00

13PV

C f

lang

ed T

ail

piec

e-

--

--

195.

0023

4.00

292.

0034

1.00

567.

0074

3.00

1112

.00

Not

e :

1)Th

e ab

ove

rate

s ar

e ba

sic

rate

s in

clus

ive

of t

rans

port

atio

n ch

arge

s an

ywhe

re in

Tam

ilnad

u.

2)G

ST

extr

a ap

plic

able

as

per

GO

27

1.6 UN PLASTICIZED O-PVC PIPES FOR PORTABLEWATER SUPPLY AS PER IS 16647 / 2017


No I Quarter II Quarter III Quarter IV Quarter

I PN 12.5 Class 500

1 110mm Metre 681.00

2 160mm Metre 1114.00

3 200mm Metre 1457.00

4 250mm Metre 2044.00

5 315mm Metre 2695.00

6 400mm Metre 4088.00

II PN 16 Class 500

1 110mm Metre 752.00

2 160mm Metre 1250.00

3 200mm Metre 1641.00

4 250mm Metre 2174.00

5 315mm Metre 2992.00

6 400mm Metre 4491.00




28

2.0 HDPE PIPES - PE 100 AS PER IS 4984/2016


No I Quarter II Quarter III Quarter IV QuarterPN 6

1 50 mm Metre 71.002 63 mm Metre 110.003 75 mm Metre 156.004 90 mm Metre 216.005 110 mm Metre 320.006 125 mm Metre 415.007 140 mm Metre 520.008 160 mm Metre 678.009 180 mm Metre 853.0010 200 mm Metre 1054.0011 225 mm Metre 1338.0012 250 mm Metre 1641.0013 280 mm Metre 2058.0014 315 mm Metre 2606.0015 355 mm Metre 3301.0016 400 mm Metre 4140.0017 450 mm Metre 5247.0018 500 mm Metre 6472.0019 560 mm Metre 8103.0020 630 mm Metre 10234.00

PN 81 50 mm Metre 88.002 63 mm Metre 138.003 75 mm Metre 194.004 90 mm Metre 278.005 110 mm Metre 416.006 125 mm Metre 533.007 140 mm Metre 666.008 160 mm Metre 873.009 180 mm Metre 1100.0010 200 mm Metre 1355.0011 225 mm Metre 1719.0012 250 mm Metre 2115.0013 280 mm Metre 2653.0014 315 mm Metre 3356.0015 355 mm Metre 4247.0016 400 mm Metre 5149.0017 450 mm Metre 6503.00

29

18 500 mm Metre 8041.0019 560 mm Metre 10065.0020 630 mm Metre 12727.00

PN 101 50 mm Metre 107.002 63 mm Metre 165.003 75 mm Metre 238.004 90 mm Metre 337.005 110 mm Metre 500.006 125 mm Metre 644.007 140 mm Metre 804.008 160 mm Metre 1052.009 180 mm Metre 1336.0010 200 mm Metre 1526.0011 225 mm Metre 2075.0012 250 mm Metre 2558.0013 280 mm Metre 3204.0014 315 mm Metre 4057.0015 355 mm Metre 5159.0016 400 mm Metre 6218.0017 450 mm Metre 7842.0018 500 mm Metre 9688.0019 560 mm Metre 12142.0020 630 mm Metre 15379.00

PN 12.51 50 mm Metre 126.002 63 mm Metre 204.003 75 mm Metre 287.004 90 mm Metre 419.005 110 mm Metre 621.006 125 mm Metre 796.007 140 mm Metre 998.008 160 mm Metre 1304.009 180 mm Metre 1648.0010 200 mm Metre 2031.0011 225 mm Metre 2576.0012 250 mm Metre 3165.0013 280 mm Metre 3974.0014 315 mm Metre 5032.0015 355 mm Metre 6383.00



30

16 400 mm Metre 7407.0017 450 mm Metre 9369.0018 500 mm Metre 11583.0019 560 mm Metre 14505.0020 630 mm Metre 18364.00

PN 161 50 mm Metre 155.002 63 mm Metre 253.003 75 mm Metre 349.004 90 mm Metre 501.005 110 mm Metre 749.006 125 mm Metre 967.007 140 mm Metre 1209.008 160 mm Metre 1583.009 180 mm Metre 1997.0010 200 mm Metre 2463.0011 225 mm Metre 3121.0012 250 mm Metre 3848.0013 280 mm Metre 4822.0014 315 mm Metre 6099.0015 355 mm Metre 7735.0016 400 mm Metre 8748.0017 450 mm Metre 11053.0018 500 mm Metre 13658.00






31

2.1 SPECIALS FOR HDPE PIPES AS PER IS 8360/1977/Part I, (Reaffirmed 1992)PART II and III (Reaffirmed 2002)


No90 Degree Bend Equal Tee

PN61 50 mm Each 34.00 51.002 63 mm Each 54.00 82.003 75 mm Each 93.00 142.004 90 mm Each 193.00 270.005 110 mm Each 349.00 440.006 125 mm Each 459.00 473.007 140 mm Each 632.00 649.008 160 mm Each 916.00 956.009 180 mm Each 1277.00 1359.0010 200 mm Each 1730.00 1810.0011 225 mm Each 2381.00 2555.0012 250 mm Each 3245.00 3471.0013 280 mm Each 4547.00 4826.0014 315 mm Each 7599.00 6656.0015 355 mm Each 10650.00 9309.0016 400 mm Each 15741.00 13614.0017 450 mm Each 21412.00 19328.0018 500 mm Each 29290.00 33388.0019 560 mm Each 40632.00 41735.0020 630 mm Each 52602.00 57792.00

PN 81 125 mm Each 438.00 502.002 140 mm Each 584.00 686.003 160 mm Each 832.00 993.004 180 mm Each 1161.00 1385.005 200 mm Each 1505.00 1850.006 225 mm Each 2146.00 2580.007 250 mm Each 2888.00 3481.008 280 mm Each 3995.00 4810.009 315 mm Each 8302.00 6590.0010 355 mm Each 11840.00 9167.0011 400 mm Each 17281.00 13293.0012 450 mm Each 24617.00 18774.0013 500 mm Each 33765.00 33957.0014 560 mm Each 47450.00 42515.0015 630 mm Each 67561.00 54134.00

PN 101 50 mm Each 48.00 79.002 63 mm Each 81.00 126.003 75 mm Each 135.00 214.004 90 mm Each 286.00 367.005 110 mm Each 465.00 630.006 125 mm Each 638.00 871.007 140 mm Each 936.00 1212.008 160 mm Each 1322.00 1859.009 180 mm Each 2019.00 2570.0010 200 mm Each 2587.00 3432.00

32

Sl. Description UnitRate for 2020-21

Noin Rupees

90 Degree Bend Equal Tee

11 225 mm Each 3546.00 4736.0012 250 mm Each 4736.00 6395.0013 280 mm Each 6566.00 8811.0014 315 mm Each 11514.00 12023.0015 355 mm Each 16625.00 16678.0016 400 mm Each 24389.00 24072.0017 450 mm Each 32756.00 31956.0018 500 mm Each 43446.00 54902.0019 560 mm Each 63410.00 88250.0020 630 mm Each 94046.00 125772.00

PN 12.51 125 mm Each 644.00 858.002 140 mm Each 899.00 1210.003 160 mm Each 1286.00 1801.004 180 mm Each 1786.00 2581.005 200 mm Each 2388.00 3535.006 225 mm Each 3399.00 4653.007 250 mm Each 4341.00 6350.008 280 mm Each 6213.00 8950.009 315 mm Each 13182.00 11751.0010 355 mm Each 17441.00 16812.0011 400 mm Each 24625.00 22481.0012 450 mm Each 35889.00 42548.0013 500 mm Each 49188.00 61012.0014 560 mm Each 69028.00 85655.0015 630 mm Each 98308.00 121940.00

PN 161 50 mm Each 70.00 110.002 63 mm Each 115.00 178.003 75 mm Each 194.00 299.004 90 mm Each 444.00 504.005 110 mm Each 810.00 580.006 125 mm Each 876.00 896.007 140 mm Each 1223.00 1287.008 160 mm Each 2123.00 1826.009 180 mm Each 2868.00 2588.0010 200 mm Each 3843.00 3533.0011 225 mm Each 5471.00 4894.0012 250 mm Each 6994.00 6824.0013 280 mm Each 10000.00 9543.0014 315 mm Each 17265.00 12892.0015 355 mm Each 24217.00 19522.0016 400 mm Each 35881.00 28168.0017 450 mm Each 50876.00 39160.0018 500 mm Each 77639.00 68213.00



33

3.0 A.C.PRESSURE PIPES AS PER IS 1592 / 2003

Sl.No Description UnitRate for 2020-21

in Rupees

I Class 15

1 80mm Metre 296.00

2 100mm Metre 389.00

3 125mm Metre 508.00

4 150mm Metre 715.00

5 200mm Metre 1184.00

6 250mm Metre 1500.00

7 300mm Metre 2099.00

8 350mm Metre 2559.00

9 400mm Metre 3628.00

10 450mm Metre 4307.00

II Class 20

1 80mm Metre 324.00

2 100mm Metre 495.00

3 125mm Metre 633.00

4 150mm Metre 890.00

5 200mm Metre 1515.00

6 250mm Metre 1946.00

7 300mm Metre 2735.00

8 350mm Metre 3326.00

9 400mm Metre 4746.00

10 450mm Metre 5718.00

Note : 1) The above rates are basic rates inclusive of transportation chargesanywhere in Tamilnadu.

2) GST extra applicable as per GO.

34

3.1 A.C. COUPLER AS PER IS 1592 /2003


in Rupees

I Class 15

1 80mm Each 256.00

2 100mm Each 331.00

3 125mm Each 417.00

4 150mm Each 500.00

5 200mm Each 856.00

6 250mm Each 999.00

7 300mm Each 1268.00

8 350mm Each 1655.00

9 400mm Each 2436.00

10 450mm Each 2878.00

II Class 20

1 80mm Each 272.00

2 100mm Each 351.00

3 125mm Each 449.00

4 150mm Each 591.00

5 200mm Each 919.00

6 250mm Each 1236.00

7 300mm Each 1601.00

8 350mm Each 2075.00

9 400mm Each 3094.00

10 450mm Each 3699.00



35

3.2 C.I.D.JOINTS AS PER IS 8794 / 1988


in Rupees

I Class 15

1 80mm Each 453.60

2 100mm Each 569.10

3 125mm Each 717.15

4 150mm Each 918.75

5 200mm Each 1336.65

6 250mm Each 1738.80

7 300mm Each 2097.90

8 350mm Each 3529.05

9 400mm Each 4400.55

10 450mm Each 5284.65

II Class 20

1 80mm Each 465.15

2 100mm Each 576.45

3 125mm Each 773.85

4 150mm Each 931.35

5 200mm Each 1420.65

6 250mm Each 1872.15

7 300mm Each 1949.85

8 350mm Each 3754.80

9 400mm Each 4506.60

10 450mm Each 5323.50



36

4.0 C.I. SPUN PIPES AS PER IS 1536/2001 Amendment No.3. July 2008

Sl No. Description Unit Rate for 2020- 21in Rupees

I LA Class

1 80mm Metre 1034.00

2 100mm Metre 1281.00

3 125mm Metre 1670.00

4 150mm Metre 1982.00

5 200mm Metre 2865.00

6 250mm Metre 3861.00

7 300mm Metre 4979.00

8 350mm Metre 6442.00

9 400mm Metre 7839.00

10 450mm Metre 9453.00

11 500mm Metre 11066.00

12 600mm Metre 14747.00

13 700mm Metre 18927.00

14 750mm Metre 21270.00

II A Class

1 80mm Metre 1124.00

2 100mm Metre 1411.00

3 125mm Metre 1824.00

4 150mm Metre 2170.00

5 200mm Metre 3110.00

6 250mm Metre 4194.00

7 300mm Metre 5443.00

8 350mm Metre 6988.00

9 400mm Metre 8567.00

10 450mm Metre 10385.00

11 500mm Metre 12055.00

12 600mm Metre 16099.00

13 700mm Metre 20614.00

14 750mm Metre 23155.00

37

III B Class

1 80mm Metre 1206.00

2 100mm Metre 1505.00

3 125mm Metre 1964.00

4 150mm Metre 2336.00

5 200mm Metre 3364.00

6 250mm Metre 4548.00

7 300mm Metre 5899.00

8 350mm Metre 7579.00

9 400mm Metre 9248.00

10 450mm Metre 11204.00

11 500mm Metre 13041.00

12 600mm Metre 17441.00

13 700mm Metre 22211.00

14 750mm Metre 25050.00

Sl. Description Unit Rate for 2020-21No. in Rupees




38

4.1 C.I D/F PIPES AS PER IS 7181/1986 & IS 1537/1996

Sl. Description Unit Rate for 2020 - 21No. in Rupees

I STANDARD

1 80mm to 200mm Kg 71.00

2 250mm to 400mm Kg 74.00

3 450mm to 750mm Kg 78.00

II NON-STANDARD

1 80mm to 200mm Kg 76.00

2 250mm to 400mm Kg 78.00

3 450mm to 750mm Kg 82.00

4.2 CI D/F SPECIALS & S/S SPECIALS AS PER IS 1538/1993


I STANDARD

1 80mm to 200mm Kg 67.00

2 250mm to 400mm Kg 78.00

3 450mm to 750mm Kg 85.00

II. NON-STANDARD

1 80mm to 200mm Kg 71.00

2 250mm to 400mm Kg 82.00

3 450mm to 750mm Kg 88.00

Note: 1) The above rates are basic rates inclusive of transportation charges anywherein Tamilnadu.


39

5.0 G I PIPES (MEDIUM) AS PER IS 1239/PART I/2004


1 15mm Metre 96.00

2 20mm Metre 128.00

3 25mm Metre 186.00

4 32mm Metre 233.00

5 40mm Metre 271.00

6 50mm Metre 369.00

7 65mm Metre 472.00

8 80mm Metre 584.00

9 100mm Metre 832.00

10 125mm Metre 1196.00

11 150mm Metre 1338.00




40

5.1a G.I. SPECIALS AS PER IS 1239/PART II

Sl.No. Description UnitRates for 2020-21

in Rupees

GI REDUCER (HEAVY)

1 150 mm x 125 mm Each 791.002 150 mm x 100 mm Each 814.003 150 mm x 80 mm Each 814.004 125 mm x 100 mm Each 719.005 125 mm x 80 mm Each 733.006 125 mm x 65 mm Each 726.007 125 mm x 50 mm Each 733.008 100 mm x 80 mm Each 505.009 100 mm x 65 mm Each 505.0010 100 mm x 50 mm Each 494.0011 80 mm x 65 mm Each 306.0012 80 mm x 50 mm Each 315.0013 80 mm x 40 mm Each 309.0014 80 mm x 32 mm Each 315.0015 65 mm x 50 mm Each 216.0016 65 mm x 40 mm Each 212.0017 65 mm x 32 mm Each 216.0018 65 mm x 20 mm Each 214.0019 50 mm x 40 mm Each 119.0020 50 mm x 32 mm Each 115.0021 50 mm x 20 mm Each 119.0022 40 mm x 32 mm Each 81.0023 40 mm x 20 mm Each 83.00

GI REDUCER (MEDIUM)

1 150 mm x 125 mm Each 662.002 150 mm x 100 mm Each 649.003 150 mm x 80 mm Each 662.004 125 mm x 100 mm Each 544.005 125 mm x 80 mm Each 560.006 125 mm x 65 mm Each 554.007 125 mm x 50 mm Each 560.008 100 mm x 80 mm Each 357.009 100 mm x 65mm Each 364.0010 100 mm x 50 mm Each 364.0011 80 mm x 65 mm Each 199.0012 80 mm x 50 mm Each 159.00

41

Sl.No. Description Unit Rates for 2020-21in Rupees

13 80 mm x 40 mm Each 154.00

14 80 mm x 32 mm Each 156.00

15 65 mm x 50 mm Each 114.00

16 65 mm x 40 mm Each 114.00

17 65 mm x 32 mm Each 114.00

18 65 mm x 20 mm Each 113.00

19 50 mm x 40 mm Each 77.00

20 50 mm x 32 mm Each 75.00

21 50 mm x 20 mm Each 77.00

22 40 mm x 32 mm Each 49.00

23 40 mm x 20 mm Each 49.00

G I UNEQUAL TEE (HEAVY)

1 150 mm x 125 mm Each 1688.00

2 150 mm x 100 mm Each 1705.00

3 150 mm x 80 mm Each 1738.00

4 125 mm x 100 mm Each 1412.00

5 125 mm x 80 mm Each 1412.00

6 125 mm x 65 mm Each 1399.00

7 125 mm x 50 mm Each 1412.00

8 100 mm x 80 mm Each 962.00

9 100 mm x 65mm Each 981.00

10 100 mm x 50 mm Each 981.00

11 80 mm x 65 mm Each 556.00

12 80 mm x 50 mm Each 572.00

13 80 mm x 40 mm Each 561.00

14 80 mm x 32 mm Each 570.00

15 65 mm x 50 mm Each 421.00

16 65 mm x 40 mm Each 413.00

17 65 mm x 32 mm Each 421.00

18 65 mm x 20 mm Each 417.00

19 50 mm x 40 mm Each 250.00

20 50 mm x 32 mm Each 243.00

21 50 mm x 20 mm Each 250.00

22 40 mm x 32 mm Each 155.00

23 40 mm x 20 mm Each 158.00

24 32 mm x 20 mm Each 113.00

42

G.I UNEQUAL TEE(MEDIUM)

1 150 mm x 125 mm Each 1043.002 150 mm x 100 mm Each 1043.003 150 mm x 80 mm Each 1023.004 125 mm x 100 mm Each 846.005 125 mm x 80 mm Each 846.006 125 mm x 65 mm Each 838.007 125 mm x 50 mm Each 846.008 100 mm x 80 mm Each 557.009 100 mm x 65mm Each 557.0010 100 mm x 50 mm Each 546.0011 80 mm x 65 mm Each 266.0012 80 mm x 50 mm Each 274.0013 80 mm x 40 mm Each 274.0014 80 mm x 32 mm Each 274.0015 65 mm x 50 mm Each 193.0016 65 mm x 40 mm Each 190.0017 65 mm x 32 mm Each 193.0018 65 mm x 20 mm Each 193.0019 50 mm x 40 mm Each 111.0020 50 mm x 32 mm Each 112.0021 50 mm x 20 mm Each 114.0022 40 mm x 32 mm Each 83.0023 40 mm x 20 mm Each 83.0024 32 mm x 20 mm Each 82.00

MS BOLTS AND NUTS

1 16 mm dia x 65 to 90 mmlength fully threaded boltsand nuts with 2 Nos. Kg. 99.00

2 20mm dia and above x 90mmto 120mm length fully threadedbolts and with nuts 2 Nos. Kg. 104.00RUBBER INSERTION SHEET

1 3 Ply R.I. Sheet Kg. 86.00AC COWL

1 80 mm dia Each 30.002 100 mm dia Each 52.00

Note : 1) The above rates are basic rates inclusive of transportationcharges anywhere in Tamilnadu.


Sl.No. Description Unit Rates for 2020-21in Rupees

43

5.1

b

G.I

. S

PEC

IALS

A

S P

ER

IS

12

39

/P

AR

T I

I

C

ON

TIN

UED

….

Sl.

Desc

ripti

on

Rate

for

20

20

-21

in

Ru

pees

No.

15m

m20

mm

25m

m32

mm

40m

m50

mm

65m

m80

mm

100m

m12

5mm

150m

m

1G.

I. Eq

ual E

lbow

pla

in23

.00

31.5

049

.00

82.9

510

3.95

156.

0028

0.00

412.

6573

7.00

760.

0018

22.8

0

2G.

I. Eq

ual T

ee p

lain

36.7

545

.00

65.0

095

.55

139.

6523

1.00

363.

0051

5.55

922.

9513

30.0

018

61.6

5

3G.

I. Co

uplin

g22

.00

22.0

029

.00

53.5

582

.95

120.

7520

7.90

256.

0051

1.00

770.

7015

54.0

0

4G.

I. Fl

ange

set

——

——

—73

.50

90.0

010

3.95

171.

0024

9.90

885.

00

5G.

I. Cr

oss

53.5

568

.00

112.

0018

0.60

232.

0035

0.70

542.

8585

7.85

1128

.95

1421

.70

—

6G.

I. He

x Ni

pple

22.0

038

.85

38.8

560

.90

76.6

510

6.00

180.

6025

4.00

376.

9540

2.00

866.

00

7G.

I.Thr

ee W

ay E

lbow

47.0

072

.00

107.

0016

9.00

219.

0035

2.80

——

——

—

8G.

I.Plu

g Di

a He

ad Ta

per T

hrea

d9.

0021

.00

21.0

035

.70

35.7

065

.00

89.0

012

9.00

180.

6023

9.00

—

9G.

I.Ben

d22

.00

38.8

560

.90

72.0

095

.55

142.

8024

2.55

366.

0064

2.60

929.

0021

98.7

0

10G.

I.Uni

on64

.00

68.0

011

5.50

162.

7520

6.85

294.

0055

1.00

768.

6011

41.0

015

25.6

522

68.0

0

11G.

I.sto

p co

ck17

0.00

227.

8541

2.65

615.

0091

4.55

1323

.00

1687

.00

2228

.00

3414

.60

4885

.65

—

12Ru

bber

shee

t for

Fla

nge

set

——

——

14.7

014

.70

21.0

040

.95

43.0

098

.70

13G.

I. Re

duce

d El

bow

Pla

in29

.00

33.6

056

.70

90.0

011

7.60

172.

0030

1.00

458.

8579

0.65

1140

.00

1538

.00

14G.

I.Red

uced

Tee

Plai

n40

.95

55.6

584

.00

120.

7515

3.00

232.

0035

5.95

551.

0010

38.0

014

65.8

017

50.0

0

15G.

I. Re

duce

d So

cket

Pla

in23

.00

47.0

051

.00

72.0

011

1.00

158.

5520

2.65

312.

9044

1.00

570.

0082

3.00

16G.

I. Ch

eck

Nut

14.7

021

.00

28.0

042

.00

55.6

575

.60

124.

9516

4.85

219.

0027

8.00

802.

00

17G.

I.Red

uced

Nip

ple

22.0

025

.00

46.0

089

.00

106.

0016

0.65

300.

0034

7.55

488.

0069

3.00

866.

00

18G.

I. Du

mm

y (H

eavy

)—

——

—23

.00

36.7

546

.00

60.9

010

7.00

154.

00—

19G.

I.Dum

my

(Med

ium

)—

——

—21

.00

30.0

042

.00

51.0

098

.70

152.

00—

20M

.S.S

addl

e Pi

ece

——

——

—90

.00

95.5

511

4.00

152.

0019

5.00

602.

70

21W

aste

Not

Tap

—12

9.00

——

——

——

——

—

22C.

I.Foo

tval

ve w

ith st

aine

r—

——

——

402.

00—

597.

00—

——

23M

.S.C

lam

pset

——

——

178.

5020

6.85

354.

9049

7.70

592.

00—

868.

00

Note

:1)

The

abov

e ra

tes

are

basi

c ra

tes

incl

usiv

e of

tra

nspo

rtat

ion

char

ges

anyw

here

in

Tam

ilnad

u.2)

GS

T ex

tra

appl

icab

le a

s pe

r G

O

44

5.2

G.M

GA

TE

VA

LV

ES

A

S P

ER

IS

BS

51

54

an

d r

ela

ted

IS

Sp

ecs

Sl.

No.

Desc

rip

tion

Rate

fo

r 2

02

0-2

1

in R

up

ees

15m

m20

mm

25m

m32

mm

40m

m50

mm

65m

m80

mm

100m

m12

5mm

1G.

M. G

ate

valv

es—

498.

7566

8.85

871.

0012

00.1

519

09.0

029

23.0

047

34.4

579

56.0

011

541.

60

2G.

M. N

on R

etur

n va

lves

——

——

—19

27.8

019

73.0

030

96.4

5—

—

Not

e:

1)Th

e ab

ove

rate

s ar

e ba

sic

rate

s in

clus

ive

of t

rans

port

atio

n ch

arge

s an

ywhe

re in

Tam

ilnad

u.2)

GS

T ex

tra

appl

icab

le a

s pe

r G

O

45

6.0 DUCTILE IRON SOCKET/SPIGOT PIPES FOR CLASS K7AS PER IS 8329/2000


1 100 mm Metre 1019.00

2 150 mm Metre 1475.00

3 200 mm Metre 1904.00

4 250 mm Metre 2505.00

5 300 mm Metre 3160.00

6 350mm Metre 3884.00

7 400 mm Metre 4664.00

8 450 mm Metre 5513.00

9 500 mm Metre 6494.00

10 600 mm Metre 8563.00

11 700 mm Metre 10508.00

12 750 mm Metre 12063.00

13 800 mm Metre 13495.00

14 900 mm Metre 15734.00

15 1000 mm Metre 20485.00


2) Unloading, stacking at stock yard and Conveyance from stock yard tosite are extra.


46

6.1 DUCTILE IRON SOCKET/SPIGOT PIPES FOR CLASS K9AS PER IS 8329/2000


1 100 mm Metre 1155.00

2 150 mm Metre 1697.00

3 200 mm Metre 2290.00

4 250 mm Metre 3016.00

5 300 mm Metre 3808.00

6 350mm Metre 4647.00

7 400 mm Metre 5577.00

8 450 mm Metre 6705.00

9 500 mm Metre 7752.00

10 600 mm Metre 10266.00

11 700 mm Metre 11840.00

12 750 mm Metre 13276.00

13 800 mm Metre 14720.00

14 900 mm Metre 17793.00

15 1000 mm Metre 21325.00




47

6.2 DUCTILE IRON CLASS PN10 FLANGED PIPES

AS PER IS 8329/2000


I 4 m length of pipes

1 80 mm Each 5661.002 100 mm Each 6419.003 150 mm Each 9244.004 200 mm Each 12431.005 250 mm Each 16375.006 300 mm Each 21071.007 350mm Each 28400.008 400 mm Each 36373.009 450 mm Each 44031.0010 500 mm Each 51501.0011 600 mm Each 66655.0012 700 mm Each 88660.0013 750 mm Each 102859.0014 800 mm Each 114164.0015 900 mm Each 155792.0016 1000mm Each 182808.00

II 5 m length of pipes

1 80 mm Each 6565.002 100 mm Each 8336.003 150 mm Each 12141.004 200 mm Each 16044.005 250 mm Each 21793.006 300 mm Each 27843.007 350 mm Each 33611.008 400 mm Each 42308.009 450 mm Each 50995.0010 500 mm Each 58763.0011 600 mm Each 77039.0012 700 mm Each 97425.0013 750 mm Each 111119.0014 800 mm Each 124469.0015 900 mm Each 169257.0016 1000 mm Each 198964.00

III 1 m length of pipes

1 80 mm Each 2632.002 100 mm Each 3137.003 150 mm Each 4349.00

48


4 200 mm Each 5787.005 250 mm Each 7780.006 300 mm Each 10143.007 350mm Each 12918.008 400 mm Each 17554.009 450 mm Each 21511.0010 500 mm Each 24514.0011 600 mm Each 31152.0012 700 mm Each 41600.0013 750 mm Each 47793.0014 800 mm Each 53985.0015 900 mm Each 75101.0016 1000mm Each 87175.00

IV 1.5 m length of pipes


V 2 m length of pipes

1 80 mm Each 3855.002 100 mm Each 4031.003 150 mm Each 5604.004 200 mm Each 7516.005 250 mm Each 9996.006 300 mm Each 12939.007 350mm Each 17201.008 400 mm Each 22676.00

49

9 450 mm Each 27598.0010 500 mm Each 31582.0011 600 mm Each 40527.0012 700 mm Each 54372.0013 750 mm Each 63137.0014 800 mm Each 71903.0015 900 mm Each 98941.0016 1000mm Each 115508.00VI 2.5 m length of pipes

1 80 mm Each 4467.002 100 mm Each 4478.003 150 mm Each 6231.004 200 mm Each 8380.005 250 mm Each 11102.006 300 mm Each 14337.007 350 mm Each 19341.008 400 mm Each 25238.009 450 mm Each 30643.0010 500 mm Each 35117.0011 600 mm Each 45218.0012 700 mm Each 60760.0013 750 mm Each 69054.0014 800 mm Each 77349.0015 900 mm Each 106042.0016 1000 mm Each 124043.00VII 3 m length of pipes

1 80 mm Each 4826.002 100 mm Each 4924.003 150 mm Each 6859.004 200 mm Each 9243.005 250 mm Each 12284.006 300 mm Each 15773.007 350mm Each 21484.008 400 mm Each 27794.009 450 mm Each 33688.0010 500 mm Each 38649.0011 600 mm Each 49908.00


50

12 700 mm Each 67151.0013 750 mm Each 76537.0014 800 mm Each 85923.0015 900 mm Each 117441.0016 1000mm Each 137599.00

VIII 3.5 m length of pipes






51

6.3 DUCTILE IRON SPECIALS AS PER IS 9523/2000


in Rupees

ALL SOCKET

1 100mm - 200 mm dia Kg 116.00

2 250 mm - 300 mm dia Kg 116.00

3 350 mm - 450 mm dia Kg 116.00

4 500 mm - 600 mm dia Kg 116.00

5 700 mm - 750 mm Kg 170.00

6 800mm Kg 170.00

7 900 mm Kg 179.00

8 1000 mm Kg 194.00

ALL FLANGE

1 100mm - 200 mm dia Kg 122.00

2 250 mm - 300 mm dia Kg 122.00

3 350 mm - 450 mm dia Kg 122.00

4 500 mm - 600 mm dia Kg 122.00

5 700 mm - 750 mm Kg 179.00

6 800 mm Kg 179.00

7 900 mm Kg 195.00

8 1000 mm Kg 195.00



3) In respect of flanged and spigot, flanged and socketted type specials,the rate applicable for flanged type specials is allowed.

52

7.0 HOUSE SERVICE CONNECTION IN WSS.

Sl.No Description Unit Rate for2020-21 in

Rupees.1 HSC Connection in HDPE Mains for Water

Supply SchemeElectrofusion tapping saddle PE 80 blue, PN 12.5with female threaded metal insert of SS 304 asper standards BS EN 12201 tested as per BS6920 for drinking water in WRC-NSF ltd, UK. (NonWrap with top loading type). Sizes:63mm to315mm dia distribution HDPE pipes.20mm (1/2”) 1 No. 538.0025mm (3/4”) 1 No. 538.0032mm (1”) 1 No. 538.00

2 HSC Connection in DI Mains for Water SupplySchemeProviding suitable dia non corrosive engineeringplastic moulded Clamp Saddle with SS 304threaded metal inserted for tapping outlet suitingfor ½”, 3/4” &1” clear bore and with wide plasticstrap (Engineering Plastic) with SS 304 suitablebolts & nuts. Saddle to have sealing of Thermoplastic elastomeric (TPE) material around shallas detailed in a drawing furnished.20mm (1/2”) 1 No. 692.0025mm (3/4”) 1 No. 795.0032mm (1”) 1 No. 823.00

3 Common Items for HSC Connectioni Brass Ferrule as per IS 319 grade of sizes 15mm,

20mm and 25mm size and threaded as per IS :554BSPT, ISO:7-1 to suit the corresponding boresizes of 15mm, 20mm and 25mm dia size(1/2", 3/4" and 1") in the saddle Connection, asper IS:1554 BSPT, ISO:7-115mm (1/2”) 1 No. 141.0020mm (3/4”) 1 No. 234.0025mm (1”) 1 No. 299.00

ii Poly Propylene compression Female ThreadedAdaptor with metal insert of SS 304 as perstandards ISO 14236 and Tested as per BS 6920in WRC-NSF LTD, UK for connecting 15mm, 20mmand 25mm outlet points of Brass ferrule of sizes15mm, 20mm and 25mm respectively.

53


Rupees

20mm (1/2”) 1 No. 117.0025mm (3/4”) 1 No. 150.0032mm (1”) 1 No. 178.00

iii Poly propylene 90 Degree Compression elbow withcompression joint at both ends as per standardsISO 14236 and Tested as per BS 6920 in WRC-NSF LTD, UK suitable for 20mm, 25mm and 32mmOD MDPE pipes20mm (1/2”) 1 No. 66.0025mm (3/4”) 1 No. 85.0032mm (1”) 1 No. 135.00

iv Poly Propylene compression Female ThreadedElbow with metal insert of SS 304 as perstandards ISO 14236 and Tested as per BS 6920in WRC-NSF LTD, UK suitable for 20mm, 25mmand 32mm OD MDPE pipes20mm (1/2”) 1 No. 117.0025mm (3/4”) 1 No. 149.0032mm (1”) 1 No. 178.00

v Poly Propylene compression Male ThreadedAdaptor with metal insert of SS 304 as perstandards ISO 14236 and Tested as per BS 6920in WRC-NSF LTD, UK suitable for 20mm, 25mmand 32mm OD MDPE pipes20mm (1/2”) 1 No. 112.0025mm (3/4”) 1 No. 146.0032mm (1”) 1 No. 178.00

vi MDPE PE 80 PN16 Blue pipe as per standardsISO 4427 and Tested as per BS 6920 in WRC-NSF LTD, UK20mm (1/2”) 1M 19.00

vii MDPE PE 80 PN12.5 Blue pipe as per standardsISO 4427 and Tested as per BS 6920 in WRC-NSF LTD, UK, suitable for 20mm, 25mm and 32mmOD MDPE pipes25mm (3/4”) 1M 26.0032mm (1”) 1M 29.00

viii U PVC ball valve with one side compression endand other side female end as per ISO 4422-4and Tested as per BS 6920 in WRC-NSF LTD,UK,size : 20mm ODx1/2"ID, 25mm ODX1/2"ID and32mm OD X 3/4" ID

54



20mm (1/2”) 1 No. 117.0025mm (3/4”) 1 No. 150.0032mm (1”) 1 No. 178.00

ix Supply and delivery of protection box of size20cm x 30cm for fixing of Water Meter. The boxshould be rectangular base in construction andmaterial of construction should be weatherresistant polyethylene (PE) blue /block.Reinforcement rips should be provided at thewalls of the box. Box should be at twocomponents comprising body and lid. Lid shouldbe press fitted to the body. No hinges should beused for opened /closed. Operation meter boxshould be provided with built in lock. The bodyas inlet and outlet windows to pass the pipethrough suitable for use with pipes of sizes upto 1" .Base of the box should be designed insuch a way That the box can be installed to thefloor/wall using anchor Bolts / screws withoutgrouting the entire base of the meter Box.Provision for fixing Name plate showing the nameof the Department etc., complete and as directedby the TWAD Board Officers.


Rupees

1 No. 430.00

55

8.0 BAR WRAPPED STEEL CYLINDER PIPES AS PER IS 15155 - 2002


in Rupees

4 Ksc Pipe

1 350mm Metre 3207.002 400mm Metre 3551.003 450mm Metre 4081.004 500mm Metre 4451.005 600mm Metre 5719.006 700mm Metre 6640.007 800mm Metre 7599.008 900mm Metre 9436.009 1000mm Metre 10927.0010 1100mm Metre 15636.0011 1200mm Metre 17357.0012 1300mm Metre 19186.0013 1400mm Metre 21418.0014 1500mm Metre 25498.00

6 Ksc Pipe


8 Ksc Pipe

1 350mm Metre 3212.002 400mm Metre 3562.003 450mm Metre 4092.004 500mm Metre 4473.005 600mm Metre 5735.006 700mm Metre 6679.00

56

7 800mm Metre 7621.008 900mm Metre 9452.009 1000mm Metre 10958.0010 1100mm Metre 15661.0011 1200mm Metre 17357.0012 1300mm Metre 19208.0013 1400mm Metre 21452.0014 1500mm Metre 25540.00

10 Ksc Pipe


12 Ksc Pipe



in Rupees

57

14 Ksc Pipe


16 Ksc Pipe


18 Ksc Pipe

1 350mm Metre 3230.002 400mm Metre 3611.003 450mm Metre 4297.004 500mm Metre 4297.005 600mm Metre 6374.006 700mm Metre 7972.00


in Rupees

58

7 800mm Metre 9722.008 900mm Metre 11624.009 1000mm Metre 13450.0010 1100mm Metre 17018.0011 1200mm Metre 19830.0012 1300mm Metre 22710.0013 1400mm Metre 26235.0014 1500mm Metre 31972.00


in Rupees



59

9.0 PIPES FOR UGSS


Rupees.

1 Supply and Delivery of DWC Structured WallPolyethylene Piping Systems (Pipe with online/

offline coupler and elastomeric sealing ring)

with required specials non-smooth externalannular corrugated and smooth internal surface

(Double wall) (SN 8 Class) for non-pressure

underground sewerage, drainage applicationgenerally as per IS-16098 (Part-2) type B.

a 150mm ID SN 8 pipe Per M 231.00

b 200mm ID SN 8 pipe Per M 372.00c 250mm ID SN 8 pipe Per M 599.00

d 300mm ID SN 8 pipe Per M 797.00

2 Supply and delivery of HDPE pipes for seweragePE 100 PN 6 conforming to IS : 14333/1996

(Ammended on 2009)

a 355 mm/ PN.6/HDPE Pipe ‘ISI’(PE 100 Grade) Per M 3871.00b 400 mm/ PN.6/HDPE Pipe ‘ISI’(PE 100 Grade) Per M 5030.00

c 450 mm/ PN.6/HDPE Pipe ‘ISI’(PE 100 Grade) Per M 6353.00

d 500 mm/ PN.6/HDPE Pipe ‘ISI’(PE 100 Grade) Per M 7851.00e 560 mm/ PN.6/HDPE Pipe ‘ISI’(PE 100 Grade) Per M 9813.00

f 630 mm/ PN.6/HDPE Pipe ‘ISI’(PE 100 Grade) Per M 12428.00

g 710 mm/ PN.6/HDPE Pipe ‘ISI’(PE 100 Grade) Per M 15772.00



60

10.0 M.S. PIPES- SPIRAL/LONGITUDIDNAL WELDING AS PER IS 3589/2001WITH INTERNAL LINING AND EXTERNAL COATING MADE WITH FE410

Sl.No.

Dia metre &thickness ofpipe in mm

Barepipeper

metre

CMLInternal6mm to12mm

thick permetreas per

table ofIS3589 :

2001

CMCexternal

20mmthick per

metre

Internalfood

gradeepoxy

coating406

micr.permetre

Externalepoxy

Coating406

micr.per

metre

CTEexternaldouble

coating &double

wrappingminimum

4mm thickper metre

ExternalPolyethy-

leneSheet ingper metre

1 168.3X2.6 630.00 344.00 551.00 571.00 725.00 630.00 789.00

2 168.3X3.2 772.00 344.00 551.00 571.00 725.00 630.00 789.00

3 168.3X4 963.00 344.00 551.00 571.00 725.00 630.00 789.00

4 168.3X4.5 1082.00 344.00 551.00 571.00 725.00 630.00 789.00

5 219.1X2.6 825.00 466.00 734.00 740.00 945.00 819.00 1029.00

6 219.1X3.6 1134.00 466.00 734.00 740.00 945.00 819.00 1029.00

7 219.1X4.5 1365.00 466.00 734.00 740.00 945.00 819.00 1029.00

8 219.1X6.3 1890.00 466.00 734.00 740.00 945.00 819.00 1029.00

9 273X3.6 1420.00 580.00 894.00 922.00 1155.00 1050.00 1310.00

10 273X4 1577.00 580.00 894.00 922.00 1155.00 1050.00 1310.00

11 273X5 1943.00 580.00 894.00 922.00 1155.00 1050.00 1310.00

12 273X6.3 2363.00 580.00 894.00 922.00 1155.00 1050.00 1310.00

13 323.9X4 1872.00 690.00 1029.00 1103.00 1363.00 1253.00 1557.00

14 323.9X4.5 1941.00 690.00 1029.00 1103.00 1363.00 1253.00 1557.00

1 Supply and Delivery of MS pipes of preferred dimensions ranging from 168.30mm ODto 2540mm OD having 2.6mm to 25mm thickness as per Table- 5 of IS 3589/2001fabricated with Fe410 grade steel conforming to IS 3589:2001 and other alliedcodes.

2 Pipes shall be internally lined with plant applied cement mortar lining 1:2, The Liningthickness range from 6 mm to 12 mm for 168.3 mm OD to 2540 mm OD as per Table -8 of IS 3589:2001

3 Pipes shall be externally coated with plant applied CM 1:3, 20mm thick minimumincluding reinforcement as per clause A-9 of Annex-A of IS 3589:2001

4 Pipes shall be internally lined with plant applied Food Grade Liquid epoxy coating ofminimum dry film thickness (DFT)of 406 microns as per Annex -B ,Clause- 1.2 of IS3589:2001

5 Pipes shall be externally coated with plant applied Food grade liquid Epoxy coating of406 microns dry film minimum thickness (DFT)as per Annex - B of IS 3589:2001

6 Pipes shall be externally coated double coating & double wrapping minimum 4mm thickper metre with plant applied coal Tar as per clause 6.1 of IS 10221:2008recommendations.

7 External polyethylene sheathing as per IS recommendations

Rate for 2020-21 in Rupees

61

15 323.9X5.6 2468.00 690.00 1029.00 1103.00 1363.00 1253.00 1557.00

16 323.9X7.1 3255.00 690.00 1029.00 1103.00 1363.00 1253.00 1557.00

17 355.6X4 1994.00 753.00 1145.00 1103.00 1460.00 1322.00 1680.00

18 355.6X5 2520.00 753.00 1145.00 1103.00 1460.00 1322.00 1680.00

19 355.6X5.6 2835.00 753.00 1145.00 1103.00 1460.00 1322.00 1680.00

20 355.6X8 3885.00 753.00 1145.00 1103.00 1460.00 1322.00 1680.00

21 406.4X4 2258.00 869.00 1298.00 1395.00 1680.00 1431.00 1890.00

22 406.4X5 2625.00 869.00 1298.00 1395.00 1680.00 1431.00 1890.00

23 406.4X6.3 3570.00 869.00 1298.00 1395.00 1680.00 1431.00 1890.00

24 406.4X8.8 4935.00 869.00 1298.00 1395.00 1680.00 1431.00 1890.00

25 457X4 2625.00 969.00 1324.00 1395.00 1943.00 1319.00 1947.00

26 457X5 3255.00 969.00 1324.00 1395.00 1943.00 1319.00 1993.00

27 457X6.3 3939.00 969.00 1324.00 1395.00 1943.00 1319.00 1993.00

28 457X10 6300.00 969.00 1324.00 1395.00 1943.00 1319.00 1993.00

29 508X5 3623.00 1022.00 1418.00 1518.00 2023.00 1465.00 2051.00

30 508X5.6 3990.00 1022.00 1418.00 1518.00 2023.00 1465.00 2051.00

31 508X6.3 4463.00 1022.00 1418.00 1518.00 2023.00 1465.00 2051.00

32 508X11 7665.00 1022.00 1418.00 1518.00 2023.00 1465.00 2051.00

33 610X5.8 4988.00 1239.00 1680.00 1734.00 2520.00 1725.00 2730.00

34 610X6.3 5513.00 1239.00 1680.00 1734.00 2520.00 1725.00 2730.00

35 610X12.5 10499.00 1239.00 1680.00 1734.00 2520.00 1725.00 2730.00

36 711X6.3 6195.00 1508.00 1994.00 2050.00 2705.00 2019.00 3150.00

37 711X7.1 7034.00 1508.00 1994.00 2050.00 2815.00 2019.00 3150.00

38 711X14.2 14174.00 1508.00 1994.00 2050.00 2888.00 2019.00 3150.00

39 813X7.1 7140.00 1722.00 2258.00 2363.00 3114.00 2154.00 3570.00

40 813X8 9686.00 1722.00 2258.00 2363.00 3393.00 2154.00 3570.00

41 813X18 20998.00 1722.00 2258.00 2363.00 3414.00 2154.00 3570.00

42 914X8 9974.00 1830.00 2415.00 2574.00 3569.00 2520.00 4095.00

43 914X8.8 11024.00 1830.00 2415.00 2574.00 3675.00 2520.00 4095.00

44 914X10 12441.00 1830.00 2415.00 2574.00 3675.00 2520.00 4095.00

Sl.No.


Barepipeper

metre



table ofIS3589 :

2001

CMCexternal

20mmthick per

metre

Internalfood

gradeepoxy

coating406

micr.permetre

Externalepoxy

Coating406

micr.per

metre

CTEexternaldouble

coating &double

wrappingminimum

4mm thickper metre

ExternalPolyethy-



62

Note: 1) The above rates are basic rates. 2) GST extra applicable as per GO 3) Refer conveyance table for Transportation Charges.

45 914X17.5 21523.00 1830.00 2415.00 2574.00 3675.00 2520.00 4095.00

46 1016X8.8 12389.00 2044.00 2835.00 3045.00 3949.00 2933.00 4961.00

47 1016X10 14174.00 2015.00 2835.00 3045.00 4199.00 2933.00 4961.00

48 1016X20 27298.00 2044.00 2835.00 3045.00 4199.00 2933.00 4961.00

49 1067X8.8 12914.00 2101.00 2888.00 3049.00 4304.00 2994.00 5125.00

50 1067X10 14699.00 2101.00 2888.00 3049.00 4304.00 2994.00 5125.00

51 1067X11 15959.00 2101.00 2888.00 3049.00 4304.00 2994.00 5125.00

52 1118X8.8 13506.00 2260.00 2939.00 3150.00 4459.00 3056.00 5250.00

53 1118X10 15223.00 2260.00 2939.00 3150.00 4459.00 3056.00 5250.00

54 1118X11 16064.00 2260.00 2939.00 3150.00 4459.00 3056.00 5250.00

55 1219X10 16641.00 2529.00 3045.00 3255.00 4696.00 3452.00 5460.00

56 1219X11 18373.00 2529.00 2846.00 3255.00 4696.00 3452.00 5460.00

57 1219X12.5 20998.00 2529.00 2846.00 3255.00 4696.00 3452.00 5460.00

58 1422X12.5 24305.00 2798.00 3779.00 3680.00 5775.00 3779.00 6300.00

59 1422X14.2 27823.00 2798.00 3779.00 4411.00 5775.00 3779.00 6300.00

60 1626X14.2 31602.00 3336.00 4304.00 4515.00 6614.00 4692.00 7349.00

61 1626X16 36222.00 3336.00 4304.00 4515.00 6614.00 4692.00 7349.00

62 1829X14.2 36222.00 3430.00 4830.00 4935.00 7349.00 4830.00 8399.00

63 1829X16 40527.00 3430.00 4830.00 4935.00 7349.00 4830.00 7850.00

64 1829X17.5 44317.00 3430.00 4830.00 4935.00 7349.00 4830.00 8399.00

65 2032X16 45146.00 4037.00 5460.00 5775.00 8189.00 5460.00 9027.00

66 2032X17.5 48926.00 4037.00 5460.00 5775.00 8189.00 5460.00 9134.00

67 2032X20 55226.00 4037.00 5460.00 5775.00 8189.00 5460.00 9134.00

68 2235X17.5 54596.00 4521.00 5985.00 6300.00 8926.00 5985.00 9816.00

69 2235X20 62995.00 4521.00 5985.00 6300.00 8926.00 5985.00 9974.00

70 2235X22.2 68245.00 4521.00 5985.00 6300.00 8926.00 5985.00 9974.00

71 2540X20 73494.00 5166.00 6825.00 7140.00 10394.00 6929.00 11549.00

72 2540X22.2 78744.00 5166.00 6825.00 7140.00 10394.00 6929.00 11549.00

73 2540X25 89243.00 5166.00 6825.00 7140.00 10394.00 6929.00 11549.00

Sl.No.


Barepipeper

metre



table ofIS3589 :

2001

CMCexternal

20mmthick per

metre

Internalfood

gradeepoxy

coating406

micr.permetre

Externalepoxy

Coating406

micr.per

metre

CTEexternaldouble

coating &double

wrappingminimum

4mm thickper metre

ExternalPolyethy-



63

10.1 MS SPECIALS AS PER IS 1916

Sl.No. Description UnitRate for 2020-21

in Rupees

1 Supply and Delivery of MS specialswith inside lining/epoxy coatingas per IS 13620 -1993 and outsidecoating with cement mortar 20mmth ick as per IS 1916-1989 andIS 7322-1985.

2 Supply and Delivery of MS specialsa s pe r IS 7322-1985 withoutinside lining and outside coating.

3 Supply and Delivery of MS specialswithout inside lining and outsidecoating but with anti rust painting

as per IS 14589 -1999.



Kg 106.00

Kg 97.00

Kg 100.00

64

11.0 RCC NON PRESSURE SPUN PIPE AS PER IS 458/2003

RCC non pressure spun pipe with socket and spigot ends as per IS 458/2003manufactured with sulphate resistant cement with 12 mm HI -alumina lining providedfor rubber ring joints.

Sl. No. Internal Dia. UnitRate for 2020-21 in Rupees

NP2 Class NP3 Class NP4 Class

1 200mm One Metre 647.00 686.00 726.00

2 250mm One Metre 746.00 805.00 845.00

3 300mm One Metre 873.00 983.00 1083.00

4 350mm One Metre 1152.00 1690.00 1730.00

5 400mm One Metre 1430.00 1918.00 1958.00

6 450mm One Metre 1710.00 2220.00 2423.00

7 500mm One Metre 2070.00 2515.00 2796.00

8 600mm One Metre 2216.00 2892.00 3223.00

9 700mm One Metre 3261.00 4413.00 4565.00

10 800mm One Metre 3796.00 5276.00 5692.00

11 900mm One Metre 4189.00 6085.00 6581.00

12 1000mm One Metre 4967.00 6732.00 7779.00

13 1100mm One Metre 5921.00 9618.00 10710.00

14 1200mm One Metre 6794.00 11738.00 12925.00

15 1400mm One Metre 8127.00 14530.00 16557.00

16 1500mm One Metre 15975.00 17566.00 18326.00

17 1600mm One Metre 18583.00 21606.00 22461.00




65

11.1 RUBBER GASKETS AS PER IS 5382/1985 (Reaffirmed 1998)

Sl. No. Internal Dia. UnitRate for 2020-21 in Rupees

NP2 Class NP3 Class NP4 Class

1 200mm Each 32.00 37.00 44.00

2 250mm Each 37.00 44.00 51.00

3 300mm Each 44.00 51.00 57.00

4 350mm Each 51.00 63.00 69.00

5 400mm Each 70.00 84.00 88.00

6 450mm Each 90.00 100.00 101.00

7 500mm Each 100.00 120.00 120.00

8 600mm Each 120.00 150.00 156.00

9 700mm Each 157.00 183.00 196.00

10 800mm Each 180.00 215.00 221.00

11 900mm Each 240.00 270.00 277.00

12 1000mm Each 300.00 340.00 340.00

13 1100mm Each 360.00 460.00 460.00

14 1200mm Each 480.00 576.00 580.00

15 1400mm Each 600.00 740.00 740.00

16 1500mm Each 730.00 940.00 940.00

17 1600mm Each 806.00 1100.00 1100.00

Note : 1) The above rates are basic rates with inclusive of transportation chargesanywhere in Tamilnadu.


66

12.0 CI D/F SLUICE VALVE WITH CAP/ WHEELAS PER IS 14846/2000 PN 1.0 WITH ISI MARKING


in Rupees

1 50 mm Each 3774.00

2 65mm Each 4332.00

3 80mm Each 4472.00

4 100mm Each 6233.00

5 125mm Each 7826.00

6 150mm Each 9224.00

7 200mm Each 16630.00

8 250mm Each 24736.00

9 300mm Each 31863.00

10 350mm Each 46676.00

11 400mm Each 63223.00

12 450mm Each 79797.00

13 500mm Each 100201.00

14 600mm Each 139331.00

15 700mm Each 311685.00

16 750mm Each 347586.00

17 800mm Each 424004.00

18 900mm Each 555976.00

19 1000mm Each 822149.00

20 1100mm Each 995160.00

21 1200mm Each 1171944.00



3) Supply of valves includes 5 year warranty.

67

12.1 C.I. D/F REFLUX VALVE AS PER I.S. 5312/2004/ PART I/ 84 PN 1.0WITH BYE-PASS ARRANGEMENTS WITH ISI MARKING


in Rupees

1 50 mm Each 4211.00

2 65 mm Each 4693.00

3 80 mm Each 5698.00

4 100 mm Each 7360.00

5 125 mm Each 9323.00

6 150 mm Each 11138.00

7 200 mm Each 23453.00

8 250 mm Each 34575.00

9 300 mm Each 44888.00

10 350 mm Each 71075.00

11 400 mm Each 93383.00

12 450 mm Each 130894.00

13 500 mm Each 188532.00

14 600 mm Each 243643.00




68

12.2 C.I. DOUBLE AIR VALVE AS PER ISI 14845/2000


in Rupees

1 40 mm Each 3774.00

2 50 mm Each 4193.00

3 80 mm Each 7384.00

4 100 mm Each 9405.00

5 150mm Each 19006.00

6 200mm Each 26971.00

Note : 1) The above rates are basic rates inclusive of transportation charges anywherein Tamilnadu.



12.3 CI SINGLE AIR VALVE AS PER ISI 14845/2000


in Rupees

1 15mm Each 1159.00

2 25 mm Each 1667.00

3 40 mm Each 2083.00

4 50 mm Each 2309.00

5 80 mm Each 3093.00

6 100 mm Each 3367.00

7 150mm Each 5993.00




69

12.4 KINETIC AIR VALVES FOR HANDLING MORE VOLUMES OF AIR INPUMPING MAIN, DOUBLE ORIFICE KINETIC AIR VALVE CONFIRMINGTO IS 14845 TAMPER PROOF DESIGN (PN-1)


in Rupees

1 50mm 1 No. 11040.00

2 80mm 1 No. 13696.00

3 100mm 1 No. 17189.00

4 150mm 1 No. 28090.00

5 200mm 1 No. 50703.00




12.5 CI SLUICE VALVES NON RAISING SPINDLE TYPES TO PRESSURE RATINGOF 1.6 PN TO BE USED IN PUMP HOUSES (LONG BODY/ LONG FACE TOFACE) Conforming to IS.


in Rupees

1 100mm 1No. 8888.00

2 125mm 1No. 11008.00

3 150mm 1No. 13747.00

4 200mm 1No. 24502.00

5 250mm 1No. 33011.00

6 300mm 1No. 45561.00

With spur gear arrangements

7 350mm 1No. 69567.00

8 400mm 1No. 94227.00

9 450mm 1No. 116461.00

10 500mm 1No. 146155.00

11 600mm 1No. 207657.00




70

12.6 BUTTERFLY VALVES WITH TOP AND BOTTOM OF S.S. 410 SHAFT, WAFERLINER/ WITH REDUCTION GEAR UNIT (Conforming to BS 5155 & IS13095/1996)

12.6.1 WAFER LINER


in Rupees

1 100mm 1 No. 3047.00

2 150mm 1 No. 4320.00

3 200mm 1 No. 7149.00

4 250mm 1 No. 13430.00

5 300mm 1 No. 15380.00

12.6.2 D/F GEAR OPERATED


in Rupees

1 400mm 1 No. 62691.00

2 450mm 1 No. 77446.00

3 500mm 1 No. 88507.00

4 600mm 1 No. 116777.00

Conforming to standard BS 5155 Butterfly valve with Body, Disc and retainer ofCast Iron Grade F.260 with EDPM rubber sleeve. Internal hardware shall be confirmingto AISI 304. External hardware Carbon Steel shall be confirming to IS 1367. Topand bottom shaft stainless steel to AISI 410. Body and disc should be tested(Hydro test) to 15 kg/sq.cm.

12.7 NON RETURN VALVES12.7.1 WAFER TYPE (DUAL PLATE CHECK VALVE) CONFORMING TO IS


in Rupees

1 100mm 1 No. 3675.00

2 150mm 1 No. 7482.00

3 200mm 1 No. 14347.00

4 250mm 1 No. 23927.00

5 300mm 1 No. 33415.00




71

12.7.2 DOUBLE FLANGED (DUAL PLATE CHECK VALVE)


in Rupees

1 400mm 1 No. 78264.002 450mm 1 No. 83496.003 500mm 1 No. 96704.004 600mm 1 No. 119501.005 700mm 1 No. 166792.006 800mm 1 No. 232342.007 900mm 1 No. 256603.008 1000mm 1 No. 336366.009 1100mm 1 No. 361527.0010 1200mm 1 No. 386688.00

Construction conforming to standard API 594. Body should confirm cast iron GradeFG 260 (IS 210), Disc plates confirming to ASTM A216, hinch pin/ stop pin/ springshould be of SS to AISI 410/304. Body seat should be of EDPM rubber. The bodyshould be tested to 15 kg/ sq.cm and seat should be tested to 10 kg/ sq.cmNote : 1) The above rates are basic rates inclusive of transportation charges

anywhere in Tamilnadu.2) GST extra applicable as per GO3) Supply of valves includes 5 year warranty.

12.7.3 D/F NON RETURN VALVE (OUT DOOR USE)CI Single Door/ Multi Door Non return valve conforming to IS 5312/2003(part I & II)to be fixed after Water meter/ Flow recorder on pumping main near Pump housewith dash pot arrangement for 90% fast closing & 10% slow closing.


in Rupees

1 300mm 1 No. 60189.00

2 350mm 1 No. 91869.00

3 400mm 1 No. 110846.00

4 450mm 1 No. 153888.00

5 500mm 1 No. 201702.00

6 600mm 1 No. 288993.00

7 700/750mm 1 No. 486154.00

8 800mm 1 No. 564384.00

9 900mm 1 No. 1003466.00

10 1000mm 1 No. 1086195.00

11 1100mm 1 No. 1580125.00

12 1200mm 1 No. 1737580.00Note : 1) The above rates are basic rates inclusive of transportation charges

anywhere in Tamilnadu.2) GST extra applicable as per GO3) Supply of valves includes 5 years warranty

72

12.8 DI SINGLE CHAMBER AIR RELEASE VALVE

Manufacture, Supply and Delivery of Tamper proof DI single chamber air releasevalves with pressure range from PN 1.0 to 2.5 with body and cover made of DuctileIron of Grade GGG 40 or equivalent grade conforming to IS 1865 with Food GradeEpoxy Powder coating(EP-P) inside and for outside of colour blue RAL 5005. Allinternal parts such as float, shell etc., cover bolts, made of Austenitic alloy steelof SS AISI 304/316. The float shall be made of Polytetrafluroethylene/ Austeniticalloy steel of AISI 304/316. Gaskets and seals of EPDM / Neoprene rubber forTWAD Board works anywhere in Tamil Nadu.


in Rupees

1 50mm each 11959.002 80mm each 15204.00

3 100mm each 17084.00

4 150mm each 32159.00

5 200mm each 35106.00


2) GST extra applicable as per GO3) Supply of valves includes 5 year warranty.

12.9 DI D/F GATE VALVESSupply and Delivery of DI D/F Gate (sluice) valves (Soft Seated) resilient seatedsoft sealing gate valves (sluice valves) with body bonnet of ductile cast iron ofgrade GGG40 or equivalent grade, wedge fully rubber lined with EPDM, replaceablespindle nut, without gland packing and with 3 O-Ring protection on the shaft andseals of NBR and the valves should be of vaccum tight and 100% leak proof withface to face dimentions as per BS 5163-89/ ISI 14846-2000/ DIN 3202 F 4. All thevalves should be with electrostatic powder coating both inside and outside withpocket less straight through body passage. All the valves are to be compatible forburried application with pressure rating PN 10/16


in Rupees

1 50mm 1 No. 7497.00

2 80mm 1 No. 9604.00

3 100mm 1 No. 12658.00

4 150mm 1 No. 19937.00

5 200mm 1 No. 31900.00

6 250mm 1 No. 45883.00

7 300mm 1 No. 69352.00

8 350mm 1 No. 204807.00

9 400mm 1 No. 220234.00



73

12.10 DI D/F BUTTERFLY VALVESSupply and Delivery of DI D/F Butterfly Valves with GGG40 or equivalent grade asper IS 3896 (part 2) 1985 and subsequent revisions double ecentrically disc withrenevable soft seal on the disc and body seat face of stainless steel / nickel weldoverlay microfinished with powder or liquid epoxy coating with minimum thicknessof 250 microns applied on both body and disc inside and outside face to facedimensions as per AWWA C 504 or BS 5155 or IS 13095

Sl.No. Description UnitRate for 2020-21 in Rupees

PN 10 PN 16

1 400mm 1 No. 149019.00 174362.002 450mm 1 No. 191420.00 191420.003 500mm 1 No. 193245.00 193245.004 600mm 1 No. 253274.00 253274.005 700mm 1 No. 413373.00 485446.006 800mm 1 No. 520837.00 542055.007 900mm 1 No. 669861.00 708898.008 1000mm 1 No. 862691.00 888637.009 1100mm 1 No. 1021940.00 1021940.0010 1200mm 1 No. 1190674.00 1190674.00



12.11 DI Non - Return ValveManufacture, Supply and Delivery of DI D/F Slanted seat Swing Check Valve. Body ofductile cast iron of Grade GGG-40 or equivalent grade and disc of ductile cast ironGGG-40 or equivalent grade with fully encapsulated EPDM rubber, where both facescan be used. Electrostatic epoxy powder/liquid coating (EP-P) inside and outsidecolor blue RAL 5005 with minimum coating thickness of 250 microns. The EPDM rubber& Epoxy Powder should be approved by W 270. (EP-P) it is a resi-coat powder approvedfor drinking water application, applied through fusion bonding process by dipping theshot-blasted casted components heated up to 200 deg C). Face to face dimensions asper EN558-1, series 48 and flange connections as per EN 1092-2/IS 1538.


in Rupees

1 40mm 1 No. 10556.002 50mm 1 No. 10865.003 65mm 1 No. 11881.004 80mm 1 No. 14738.005 100mm 1 No. 12106.006 125 mm 1 No. 27156.007 150mm 1 No. 34144.008 200 mm 1 No. 36204.009 250mm 1 No. 92050.0010 300mm 1 No. 116964.00



74

12.12 DI Wafer type Butterfly Valve

Manufacturing, supply and delivery of resilient seated wafer type butterfly valve inaccordance with EN 593, centric disk mounted in three maintenance-free bearingbushes, tight in both flow directions, Replaceable rubber sleeve with integratedseal for functionally reliable use for flared flanges, welding flanges, PE flanges aswell as loose flanges with V-collar, Stable seat due to collar with vulcanized supportring. Vaccum tight upto 1 Torr. Face to face length acc.to 558-1, basic series 20(DIN 3202/k1). With Electrostatic epoxy powder coating (EP-P) inside and outsidecolor blue RAL 5005 with minimum coating thickness of 250 microns. The EPDMrubber & Epoxy Powder should be approved by W 270.(EP-P it is resi-coat powderapproved for drinking water application, applied through fusion bonding technologyprocess by dipping the shot-blasted casted components heated upto 200 deg C).

Sl.No. Description Unit Rate for 2020-21in Rupees

1 40mm 1 No. 9982.00

2 50mm 1 No. 9982.00

3 65mm 1 No. 10316.00

4 80mm 1 No. 11231.00

5 100mm 1 No. 13175.00

6 125 mm 1 No. 14935.00

7 150mm 1 No. 22687.00

8 200 mm 1 No. 26820.00

9 250mm 1 No. 44783.00

10 300mm 1 No. 74877.00

11 350mm 1 No. 114373.00

12 400mm 1 No. 156100.00

13 450mm 1 No. 261295.00

14 500mm 1 No. 267547.00




75

12.13 DI Disk Check Valve

Manufacture, supply and delivery of DI D/F Slanted seat Tilting Disc Swing CheckValve in single piece body and closed eye disc construction. Hemisherical discwith 59 degree inclination for fast open and closing. Corrosion proof and wearresistent(triple offset) disc face & body seat face, both made of fusion bondedNickel Chromium weld overlay and microfinished. Body and disc of ductile cast ironGGG-40 or equivalent grade, medium free(dry) shafts of stainless steel and bearingsof Zinc-free Bronze, Valve should have provision for internal damping unit forreducing the effects of water hammer/surge, if required at later stage. Electrostaticepoxy powder/liquid coating(EP-P) inside and outside color blue RAL 5005 withminimum coating thickness of 150 microns. The EPDM rubber & Epoxy Powdershould be approved by W 270.(EP-P it is a resi-coat powder approved for drinkingwater application, applied through fusion bonding technology process by dippingthe shot-blasted casted components heated upto 200deg C). Face to facedimensions as per EN 558-1 series 14 and flange connections as per EN 1092-2/IS

Sl.No. Description Unit Rate for 2020-21 in Rupees

PN 10 PN 16

1 200mm 1 No. 389909.00 389909.00

2 250mm 1 No. 392465.00 392465.00

3 300mm 1 No. 394206.00 394206.00

4 350mm 1 No. 435797.00 435797.00

5 400mm 1 No. 439073.00 439073.00

6 450mm 1 No. 547444.00 586693.00

7 500mm 1 No. 535442.00 591220.00

8 600mm 1 No. 728933.00 741087.00

9 700mm 1 No. 1606968.00 1644568.00

10 800mm 1 No. 1867943.00 1939181.00

11 900mm 1 No. 2127062.00 2163483.00

12 1000mm 1 No. 2602471.00 2635516.00




76

12.14 DI Diaphragm Type Flow Control Valve12.14.1 DI Altitude Control Valve (PN10/16) with the function to prevent waterlevel in a tank from exceeding a set level. The set level can be changed as per therequirement.“Manufacture supply and delivery of DI D/F Diaphragm type own medium controlledAltitude Control valve with cast body of ductile iron grade GGG-40 or equivalent gradeor as per IS 3896-Part-2-1985 customized control cylinder for linear control behaviouror equivalent, performed diaphragm and pull out safe profile sealing ring of EPDM,threaded inserts (CORFIX - to prevent the coating from coming off in the connectionsarea as well as corrosion and incrustations in the control circuit) or equivalent. Flangeconnection dimensions according to EN 1092, Part 2/ ISO 7005[DIN]/ IS 1538, allparts (Epoxy coating, and diaphragm) in contact with medium are as per KTW andDVGW certified (harmless)/WRAS & NSF approved. The EPDM rubber & Epoxy coating(EP-P) should be approved by W270. (EP-P)/WRAS & NSF.”Pilot valve system having Stainless Steel / Brass fittings as per standard parts accordingto DIN EN 12 266-1 with all the external control tubing of SS 304 / copper / reinforcedplastic rated PN16 Tightness to DIN EN 12 266-1, leakage rate A (or) equivalent andthe needle valve / speed control device should be provided to vary opening speed ofthe main diaphragm with self-cleaning filter to avoid possibility of dirt build up insidethe control tubing.


1 50mm 1 No. 97685.00

2 65mm 1 No. 100165.00

3 80mm 1 No. 110349.00

4 100mm 1 No. 137538.00

5 150mm 1 No. 180852.00

6 200 mm 1 No. 279681.00

7 250mm 1 No. 343889.00

8 300mm 1 No. 533148.00

9 350mm 1 No. 790866.00

10 400mm 1 No. 1345363.00Note : 1) The above rates are basic rates inclusive of transportation

charges anywhere in Tamilnadu.2) GST extra applicable as per GO


77

12.14.2 DI Pressure Reducing Valve (PN10/16) with the function to reducedownstream pressure to set point irrespective of upstream fluctuations. The downstreampressure set point can be changed as per the requirement.

“Manufacture supply and delivery of DI D/F Diaphragm type own medium controlledPressure Reducing valve with cast body of ductile iron grade GGG-40 or equivalentgrade or as per IS 3896-Part-2-1985 customized control cylinder for linear controlbehaviour or equivalent, performed diaphragm and pull out safe profile sealing ring ofEPDM, threaded inserts (CORFIX - to prevent the coating from coming off in theconnections area as well as corrosion and incrustations in the control circuit) orequivalent. 2 pressure gauges for operator-friendly control to determine the actualinlet and outlet pressure connected directly to the valve. Flange connection dimensionsaccording to EN 1092, Part 2/ ISO 7005[DIN]/ IS 1538, all parts (Epoxy coating, anddiaphragm) in contact with medium are as per KTW and DVGW certified (harmless)/WRAS & NSF approved. The EPDM rubber & Epoxy coating (EP-P) should be approvedby W270.(EP-P)/ WRAS & NSF.”

Pilot valve system having Stainless Steel / Brass fittings with spring of SS 304 as perstandard parts according to DIN EN 12 266-1 with all the external control tubing of SS304 / Copper/ reinforced plastic rated PN16, Tightness to DIN EN 12 266-1, leakagerate A (or) equivalent and the needle valve/ speed control device should be providedto vary opening speed of the main diaphragm with self-cleaning filter to avoid possibilityof dirt build up inside the control tubing.


1 50mm 1 No. 61905

2 65mm 1 No. 63012

3 80mm 1 No. 74570

4 100mm 1 No. 85818

5 150mm 1 No. 145420

6 200 mm 1 No. 202100

7 250mm 1 No. 266220

8 300mm 1 No. 455390

9 350mm 1 No. 674229

10 400mm 1 No. 1254491

Note : 1) The above rates are basic rates inclusive of transportationcharges anywhere in Tamilnadu.



78

12.14.3 DI Flow rate Limit control Valve (PN10/16) with the function to limit theflow rate to a set point. In case the downstream demand increases beyond the setlimit, the valve closes down to bring the flow back to set limit. The valve shall havean orifice plate and the orifice diameter is designed based on the set point as per therequirement and installed downstream of the control valve.

“Manufacture supply and delivery of DI D/F Diaphragm type own medium controlledFlow rate Limit Control valve with cast body of ductile iron grade GGG-40 or equivalentgrade or as per IS 3896-Part-2-1985 customized control cylinder for linear controlbehaviour or equivalent, performed diaphragm and pull out safe profile sealing ring ofEPDM, threaded inserts (CORFIX - to prevent the coating from coming off in theconnections area as well as corrosion and incrustations in the control circuit) orequivalent. Flange connection dimensions according to EN 1092, Part 2/ ISO 7005[DIN]/IS 1538, all parts (Epoxy coating, and diaphragm) in contact with medium are as perKTW and DVGW certified (harmless)/WRAS & NSF approved. The EPDM rubber &Epoxy coating (EP-P) should be approved by W270. (EP-P)/ WRAS & NSF.”

Pilot valve system having Stainless Steel / Brass fittings with spring of stainless steel304 as per standard parts according to DIN EN 12 266-1, orifice plate shall be as perthe set point of flow rate and all the external control tubing of SS 304 / Copper/reinforced plastic rated PN16, Tightness to DIN EN 12 266-1, leakage rate A (or)equivalent and the needle valve/ speed control device should be provided to varyopening speed of the main diaphragm with self-cleaning filter to avoid possibility ofdirt build up inside the control tubing.


1 50mm 1 No. 78556.00

2 65mm 1 No. 81035.00

3 80mm 1 No. 94763.00

4 100mm 1 No. 102468.00

5 150mm 1 No. 179853.00

6 200 mm 1 No. 236905.00

7 250mm 1 No. 301025.00

8 300mm 1 No. 490284.00

9 350mm 1 No. 726569.00

10 400mm 1 No. 1296294.00




79

12.14.4 DI Pressure Sustaining / Relief Valve (PN10/16) with the function torelieve excess pressure in the downstream pressure to set point irrespective of upstreamfluctuations. The downstream pressure set point can be changed as per therequirement.

“Manufacture supply and delivery of DI D/F Diaphragm type own medium controlledPressure Sustaining / Relief valve with cast body of ductile iron grade GGG-40 orequivalent grade or as per IS 3896-Part-2-1985 customized control cylinder for linearcontrol behaviour or equivalent, performed diaphragm and pull out safe profile sealingring of EPDM, threaded inserts (CORFIX - to prevent the coating from coming off inthe connections area as well as corrosion and incrustations in the control circuit) orequivalent. 2 pressure gauges for operator-friendly control to determine the actualinlet and outlet pressure connected directly to the valve. Flange connection dimensionsaccording to EN 1092, Part 2/ ISO 7005[DIN]/ IS 1538, all parts (Epoxy coating, anddiaphragm) in contact with medium are as per KTW and DVGW certified (harmless)/WRAS & NSF approved. The EPDM rubber & Epoxy coating (EP-P) should be approvedby W270.(EP-P)/ WRAS & NSF.”

Pilot valve system having Stainless Steel / Brass fittings with spring of stainless steel304 as per standard parts according to DIN EN 12 266-1 with all the external controltubing of SS 304/ Copper/ reinforced plastic rated PN16, Tightness to DIN EN 12 266-1, leakage rate A (or) equivalent and the needle valve/ speed control device shouldbe provided to vary opening speed of the main diaphragm with self-cleaning filter toavoid possibility of dirt build up inside the control tubing.


1 50mm 1 No. 61905.00

2 65mm 1 No. 64385.00

3 80mm 1 No. 74570.00

4 100mm 1 No. 85818.00

5 150mm 1 No. 145420.00

6 200 mm 1 No. 202100.00

7 250mm 1 No. 266220.00

8 300mm 1 No. 455390.00

9 350mm 1 No. 674229.00

10 400mm 1 No. 1254491.00




80

12.14.5 DI Pump control Valve (PN10/16) with the function to open / close thepump discharge to the downstream network gradually the start-up / shut-off of apump to protect the pumping assembly.

“Manufacture supply and delivery of DI D/F Diaphragm type own medium controlledPump Control Valve with cast body of ductile iron grade GGG-40 or equivalent grade oras per IS 3896-Part-2-1985 customized control cylinder for linear control behaviouror equivalent, performed diaphragm and pull out safe profile sealing ring of EPDM,threaded inserts (CORFIX - to prevent the coating from coming off in the connectionsarea as well as corrosion and incrustations in the control circuit) or equivalent. Flangeconnection dimensions according to EN 1092, Part 2/ ISO 7005[DIN]/ IS 1538, allparts (Epoxy coating, and diaphragm) in contact with medium are as per KTW andDVGW certified (harmless)/WRAS & NSF approved. The EPDM rubber & Epoxy coating(EP-P) should be approved by W270.(EP-P)/ WRAS & NSF.”

Pilot valve system having Stainless Steel / Brass fittings as per standard parts accordingto DIN EN 12 266-1 and 3 way NO 24 V AC 50/60 Hz Solenoid, all the external controltubing of SS 304/ Copper/ reinforced plastic rated PN16 with Position indicator,Tightness to DIN EN 12 266-1, leakage rate A (or) equivalent and the needle valve/speed control device should be provided to vary opening speed of the main diaphragmwith self-cleaning filter to avoid possibility of dirt build up inside the control tubing.


1 50mm 1 No. 105035.00

2 65mm 1 No. 107515.00

3 80mm 1 No. 117700.00

4 100mm 1 No. 127701.00

5 150mm 1 No. 235223.00

6 200 mm 1 No. 291773.00

7 250mm 1 No. 355262.00

8 300mm 1 No. 545546.00

9 350mm 1 No. 674229.00

10 400mm 1 No. 1254491.00




81

12.14.6 DI Pressure Reducing and Flow Limit Control Valve (PN10/16) with thefunction to reduce higher upstream pressure into a preset lower downstream pressureand to not allow flow rate in the line to exceed beyond the defined set point. The floworifice diameter is designed based on the set point as per the design requirement. Theset point can be changed to a maximum of +10%.

“Manufacture supply and delivery of DI D/F Diaphragm type own medium controlledPressure Reducing and flow limit control valve with cast body of ductile iron gradeGGG-40 or equivalent grade or as per IS 3896-Part-2-1985 customized control cylinderfor linear control behaviour or equivalent, performed diaphragm and pull out safeprofile sealing ring of EPDM, threaded inserts (CORFIX - to prevent the coating fromcoming off in the connections area as well as corrosion and incrustations in thecontrol circuit) or equivalent. 2 pressure gauges for operator-friendly control todetermine the actual inlet and outlet pressure connected directly to the valve. Flangeconnection dimensions according to EN 1092, Part 2/ ISO 7005[DIN]/ IS 1538, allparts (Epoxy coating, and diaphragm) in contact with medium are as per KTW andDVGW certified (harmless)/WRAS & NSF approved. The EPDM rubber & Epoxy coating(EP-P) should be approved by W270.(EP-P)/ WRAS & NSF.”

Pilot valve system having Stainless Steel / Brass fittings with spring of stainless steel304 as per standard parts according to DIN EN 12 266-1 and Stainless steel 316orifice plate shall be as per the set point of flow rate, all the external control tubing ofSS 304 / Copper/ reinforced plastic rated PN16, Tightness to DIN EN 12 266-1,leakage rate A (or) equivalent and the needle valve/ speed control device should beprovided to vary opening speed of the main diaphragm with self-cleaning filter toavoid possibility of dirt build up inside the control tubing.


1 50mm 1 No. 105940.00

2 65mm 1 No. 111944.00

3 80mm 1 No. 125670.00

4 100mm 1 No. 133375.00

5 150mm 1 No. 211134.00

6 200 mm 1 No. 267814.00

7 250mm 1 No. 331934.00

8 300mm 1 No. 521193.00

9 350mm 1 No. 757478.00

10 400mm 1 No. 1327201.00




82

12.14.7 DI Altitude Control and Flow Control Valve (PN10/16) with the functionto ensure that water in tank does not exceed a certain level and the same time notallow flow rate to exceed set point. The Hydraulic Valve trim connection shall havetwo metal points, one for Altitude control and Flow-rate control function. The valveshall use an orifice plated on downstream side to limit the flow rate. The set level canbe changed to a maximum of +10%.

“Manufacture supply and delivery of DI D/F Diaphragm type own medium controlledAltitude Control and Flow Control Valve with cast body of ductile iron grade GGG-40 orequivalent grade or as per IS 3896-Part-2-1985 customized control cylinder for linearcontrol behaviour or equivalent, performed diaphragm and pull out safe profile sealingring of EPDM, threaded inserts (CORFIX - to prevent the coating from coming off inthe connections area as well as corrosion and incrustations in the control circuit) orequivalent. Flange connection dimensions according to EN 1092, Part 2/ ISO 7005[DIN]/IS 1538, all parts (Epoxy coating, and diaphragm) in contact with medium are as perKTW and DVGW certified (harmless)/WRAS & NSF approved. The EPDM rubber &Epoxy coating (EP-P) should be approved by W270.(EP-P)/ WRAS & NSF.”

Pilot valve system having Stainless Steel / Brass fittings with spring of SS 304 foraltitude pilot as per standard parts according to DIN EN 12 266-1, the stainless steel316 of orifice plate and dimension of orifice as per the flow rate set point, all theexternal control tubing of SS 304 / copper / reinforced plastic rated PN16, Tightnessto DIN EN 12 266-1, leakage rate A (or) equivalent and the needle valve / speedcontrol device should be provided to vary opening speed of the main diaphragm withself-cleaning filter to avoid possibility of dirt build up inside the control tubing.


1 50mm 1 No. 129104.00

2 65mm 1 No. 131309.00

3 80mm 1 No. 143511.00

4 100mm 1 No. 150360.00

5 150mm 1 No. 219478.00

6 200 mm 1 No. 269861.00

7 250mm 1 No. 326856.00

8 300mm 1 No. 495086.00

9 350mm 1 No. 705117.00

10 400mm 1 No. 1211539.00




83

12.15 DI Plunger type flow control Valve“Manufacturing, supply and delivery of DI D/F Plunger type(Control valve) with onepiece body of ductile cast iron of grade GGG-40, all internal parts of stainless steel.Piston guides of bronze welded overlay & micro-finished and bearing bush of zinc freeBronze. Valve/profile sealing seat shall be in the no-flow zone. Double sealingeffect between the body and the plunger shall be by Quadring Seal (twist freeoperation). The valve shall be designed to operate smoothly throughout the specifiedflow range without cavitation. Corrosion protected medium free bearing in the bodyby way of double O-ring seal and encapsulated shaft seal. There shall be noobstacles in the main flow passage except the plunger and the attached controlcylinders. Plunger shall be by means of stainless steel crank drive mechanism. Face-to-face dimensions EN558-1 basic series 15 and 1.5X DN from DN500 and flangeconnections as per EN1092-2/ISO 7005[DIN]”.


1 150mm 1 No. 481058.00

2 200mm 1 No. 685418.00

3 250mm 1 No. 830341.00

4 300mm 1 No. 1084390.00

5 400 mm 1 No. 1718974.00

6 450mm 1 No. 2346954.00

7 500 mm 1 No. 2992117.00

8 600mm 1 No. 3883201.00

9 700mm 1 No. 4534731.00

10 800mm 1 No. 5435703.00

11 900mm 1 No. 7573788.00

12 1000mm 1 No. 8816497.00




84

12.16 DI Surge Control Valve

“Manufacturing, supply and delivery of Surge anticipating Relief valves againstpower failure surges or pressure waves caused by velocity changes, quick openingrelief easily adjustable pressure setting. The valve should remain closed when linepressure is between the set-points of the two pilots. The valve should openinitially when line pressure drops below the setting of the low-pressure pilot toanticipate surges associated with a pump stopping. The valve will also continue toreact and remain open when the return high-pressure wave is above the setting ofthe high-pressure pilot or open when inlet pressure exceeds a pre-determined set-point at which time the valve opens quickly. With high speed discharge, withflange dimension to EN 1092-2/ ISO 7005[DIN]. Body and cover in ductile cast ironof Grade GGG 40 or equivalent grade. All internal parts & all cover bolts of austeniticalloy steel and gaskets and seals of EPDM of grade W 270(approved for drinkingwater) with Electrostatic epoxy powder coating (EP-P) inside and outside colorblue RAL 5005 with minimum coating thickness of 250 microns”.


1 50mm 1 No. 94870.00

2 80mm 1 No. 103699.00

3 100mm 1 No. 131441.00

4 150mm 1 No. 187027.00

5 200 mm 1 No. 274964.00Note : 1) The above rates are basic rates inclusive of transportation charges

anywhere in Tamilnadu.2) GST extra applicable as per GO3) Supply of valves includes 5 year warranty.

12.17 OHT FLOW CONTROL VALVE

Supply and delivery of the following sizes of OHT flow control valve with femaleBSP treaded ends, (20mm length) with Stainless Steel Body as per ANSI 202Grade, Plug, Flange – Nylon 66, (to be tested at NABL accredited lab.) Triangularnotch type flow control path with opening reference scale arrangements for flownotch and Upstream & Downstream pressure checking spring loaded moutharrangements. Working Pressure 10 KSC, (FCRI, Palgaut pressure test and flowtest to be furnished).


a. 40mm (1 lpm to 400lpm adjustable

type arrangements) Each 5185.00

b 100mm (20 lpm to 2000 lpm

adjustable type arrangements) Each 19141.00



85

13.0 SALT GLAZED STONEWARE PIPE AS PER IS 651/2007 of 600MM length


SP1 Class SP2 Class

1 100mm Each 106.00 115.002 150mm Each 185.00 200.003 200mm Each 280.00 305.004 250mm Each 455.00 495.005 300mm Each 710.00 775.00

13.1 SALT GLAZED STONEWARE PIPE AS PER IS 651/2007 of 1000MM lengthwith Rubber Gasket


SP1 Class SP2 Class

1 150mm Each 440.00 502.002 200mm Each 660.00 720.003 250mm Each 1238.00 1345.00

13.2 SALT GLAZED STONEWARE PIPE AS PER IS 651/2007 of 1200MM lengthwith Rubber Gasket


SP1 Class SP2 Class

1 150mm Each 557.00 608.00

2 200mm Each 794.00 865.00

3 250mm Each 1500.00 1633.00




14.0 SULPHATE RESISTANT CEMENT AS PER IS 12330/1988


in Rupees1 Sulphate Resistant Cement as per IS

12330/1988 and as amended fromtime to time.

50Kg/Bag 300.00


2) GST extra applicable as per GO3) The rate is subject to revision by PWD

86

15.0 FIBER REINFORCED CONCRETE FRAME AND COVER AS PER IS 12592/2002, PART 1 & 2

Sl.No. Description Rate for 2020-21in Rupees

Supply and delivery of following sizes Heavy Extra Heavy dutyof FRC Manhole Covers / Frames to dutystores on as per IS 12592:2002 to itslatest revision with reinforcementdetails for covers and frames.

1 450mm dia FRC manhole cover tosuit 450 mm clear opening manholeframe 763.00 881.00

2 450mm dia FRC manhole frame to haveclear opening of 450mm dia to suit450mm dia FRC Cover 953.00 1103.00

3 600mm dia FRC manhole cover tosuit 600 mm clear opening manholeframe 984.00 1136.00

4 600mm dia FRC manhole frame tohave clear opening of 600mm diato suit 600mm dia FRC Cover 1405.00 1623.00



87

16.1 WATER METER CONFORMING TO IS2373/ISO 4064 & DIRT BOX STRAINER

Supply and delivery of Woltman model with removal mechanism water meters (non-domesticuse) confirming to ISO 4064 part I, II,III class B and IS 2373 with life cycle test certificatefrom FCRI/NABL accredited lab. The water meters shall have magnetic drivers or mechanicaldrivers and shall be versatile for installation in any position. The meters shall behydrodynamically, hydrostatically balanced. The runner, runner chamber, pointers of themeter shall be as per ISO 4064 specification. Dry dial excavated counter housing fullyprotected against flooding ensuring easy reading in all climates.

Sl.No. Description UnitRate for 2020-21 in Rupees

Water meter Dirt Box ErectionCharges

1 50mm Each 9249.00 2918.00 3102.00

2 80mm Each 11505.00 4726.00 3870.00

3 100mm Each 12226.00 5795.00 6024.00

4 150mm Each 17881.00 9635.00 7084.00

5 200mm Each 22258.00 11651.00 8825.00

6 250mm Each 48348.00 25041.00 10006.00

7 300mm Each 103194.00 44609.00 10720.00

8 400mm Each 183144.00 74255.00 10915.00

9 500mm Each 213133.00 108006.00 10940.00


2) GST extra applicable as per GO3) Erection charges includes earth work excavation,labour charges, cutting

and threading, conveyance,welding and hire charges for tools and plantsets., complete.

16.2 FULL BORE ELECTROMAGNETIC FLOW METER

Electromagnetic Flow Meter shall be a velocity sensing Electromagnetic type,microprocessor based signal converter, sealed housing, flanged tube meter for 1.0 Mpaworking pressure, manufactured to highest standard available for mag-meters, equippedwith minimum six digit digital totalizers, reading in different units (Kiloliters / Cubicmeter) and shall be accurate within 0.5% of Measured value, shall operate within arange of 0.3 m/sec to 4 m/sec and be constructed as follows: Meter tube (Sensor)shall be fabricated from stainless steel tube and use class PN10 flat face carbon steelflanges in accordance with IS 1538. These flanges shall be welded to the flow tube. Theinternal and external of the meter tube shall be blasted to near white and lined withhard rubber preferably by SBR or EPDM. Meter tube shall have a constant nominal insidediameter offering no obstruction to the flow. The accuracy should be inclusive oflinearity, hysteresis, repeatability, temperature and pressure effects. Coil Housing shallbe fabricated from stainless steel (SS304) for corrosion resistance and welded to thetube providing a completely sealed environment for all coils, electrode connections andwiring harness capable of submerged or buried operation with IP68 Protection. SignalConverter shall be pulsed DC coil excitation type with auto zeroing. The signal converter

88


1 10MM 1 No. 55914.002 25 MM 1 No. 44775.003 50 MM 1 No. 49925.004 80 MM 1 No. 79950.005 100 MM 1 No. 98127.006 125 MM 1 No. 102705.007 150MM 1 No. 114903.008 200MM 1 No. 142680.009 250MM 1 No. 177018.0010 300 MM 1 No. 201706.0011 350MM 1 No. 249793.0012 400MM 1 No. 302785.0013 450MM 1 No. 349423.0014 500 MM 1 No. 399545.0015 600MM 1 No. 458380.0016 700 MM 1 No. 535153.0017 800MM 1 No. 599113.0018 900 MM 1 No. 673938.0019 1000 MM 1 No. 851775.0020 1200 MM 1 No. 1223526.0021 1400MM 1 No. 1465545.0022 1600MM 1 No. 1667675.0023 1800 MM 1 No. 2214000.0024 2000 MM 1 No. 3179550.0025 2200 MM 1 No. 3328175.0026 2400MM 1 No. 3662325.0027 2600 MM 1 No. 4086163.0028 2800 MM 1 No. 4536650.0029 3000 MM 1 No. 4882075.00



shall be remotely mounted away from the meter. The converter shall indicate directionof flow and provide a flow rate indication and a total of flow volume for both forwardand reverse directions. The converter shall provide an isolated 4-20 mA output intominimum 500-ohm load and a frequency output of a maximum of 0-10 KHZ and a scaledpulse output, Communication interface is RS485, HART output. The microprocessor basedsignal converter shall have a self-diagnostic test mode and a backlit display thatcontinuously displays “Rate of Flow” and “Total Volume”. Converter shall be suppliedwith a programmable low flow drop out, higher flow and empty pipe zero return. Thesignal converter housing should be die-cast aluminum with glass window. The convertercum transmitter should be fully programmable form the front facia. The programmingshould be user friendly, self-prompting menu driven. Flow meter test calibration certificatefrom FCRI, flow test lab / NABL accredited lab to be furnished.

89

17.0 HDPE TANK


1 Supply and delivery and fixing of HDPEtank as per IS 12701 / 1996 includingloading, unloading, transportation andlabour charges for fixing of the GIpipes and specials for pipe connectionworks including cutting, threading andfixing charges etc.,200 litres 1 No. 1642.00500 litres 1 No. 3953.001000 litres 1 No. 7905.002000 litres 1 No. 18480.005000 litres 1 No. 43512.0010000 litres 1 No. 92400.00



18.0 MS KIOSK


1 Supply and delivery of MS Kiosk ofsize 0.75m x 0.45m x 0.75m made upof MS angle of size 50mm x 50mmx4mm alround covered with 16 gaugeMS sheet and kiosk door made up of 1 No 8640.00MS plates of size 25 mm x 3 mmincluding cutting, welding, grinding,locking arrangements and labourcharges etc.,



90

19.0 MS LADDERSl No. Description Unit Rate for 2020-21

in Rupees

1 Supply and Delivery and fixing of outside MSLadder of 45cm clear wide made out of 50mm x 50mm x 6mm MS angle for sides andsteps in 16 mm MS plain rods fixed at 30cm C/C welded jointed etc ., providing with suitableside supports, c lamps and lockingarrangements provided with two coats ofapproved enamel paint over one coat ofredoxide paint , for providing access to rooftop of OHT of suitable inclined length, includingbottom anchorage and transportation and asdirected by TWAD Board officers. The rateincludes concrete bed block in CC 1:2:4 using20mm HBGS at top and bottom of suitable sizewith necessry anchor bolts.For OHT Capacities

a 1. 10000 litres with - 7.5m staging height Each 23830.00b 2. 20000 litres with - 7.5m staging height Each 23830.00

2 Fabrication, supply, delivery and fixing ofoutside MS Ladder of 45cm clear wide madeout of 50 mm x 50mm x 6mm MS angle forboth sides and for steps at 30cm C/C weldedjointed etc ., for I staging from GL to 1st levelbrace (weight 4.5kg/m) IInd and IIIrd stagingupto floor slab and IVth staging from floor slabto roof top. Supply, delivery and fixing of 32mm GI pipes medium for hand rails from I stageto IVth stage. RCC M30 Grade mix for Landingslab 5 nos. at Ground Level- 1No. and aboveGround Level - 4Nos. Supply and fixing of 32mmGI pipe medium for hand rails for the Landingslab. Supplying and fixing of MS Base plate of100mm X 100mm X 6mm thick for fixingAnchore fastener bolt for fixing of hand railsat Landing slab and MS Ladder providing lockingarrangements with two coats of approvedenamel paint over one coat of red oxide paintas per approved Type Design and as directedby TWAD board officers.For OHT Capacities

a 30000 litres capacity at 12.0m staging height Each 116788.00b 40000 litres capacity at 12.0m staging height Each 116788.00c 50000 litres capacity at 12.0m staging height Each 116788.00d 60000 litres capacity at 12.0m staging height Each 116788.00e 100000 litres capacity at 12.0m staging height Each 116788.00



91

20.0 MS DOOR / WINDOW/VENTILATOR

Sl.No. Description UnitRate for2020-21

in Rupees

1 Supply and Delivery Fabrication of MSdoors and windows with outer frameand shutter frame in MS angle of size40mm x 40mm x 6 mm with MS flat25mm x 25mm x 6mm and MS sheet of18 gauge including ventilating arrange-ments using 20mm square MS rodswith locking arrangements includingtwo coats of approved enamel paintover coat of red oxide including costof angles, plates, sheets, fabricationcharges, cost of hold fast and

transportation charges etc., complete.

i Fully panelled Double leaf - Door 1.00 x 2.50 m 6710.00

ii. Fully panelled Double leaf - Door 1.00m x2.10 m 5852.00

iii. Fully panelled Double leaf - Door 1.00m x2.00 m 4288.00

iv. Fully panelled Single leaf - Door 0.75 m x2.10 m 3583.00

v Fully panelled Single leaf - Door 0.90 m x 2.00 m 3825.00

vi. Fully panelled Single leaf - Door 0.90 m x 2.10 m 4237.00

vii Fully panelled Single leaf - Door 1.00 m x2.00 m 3986.00

viii Fully panelled Double leaf - Window

(without Ventilator) 1.20 m x0.90 m 3179.00

ix Fully panelled Double leaf - Window

(without Ventilator) 0.60 m x 0.90 m 2321.00

x Ventilator 0.45 m x0.60 m 1395.00



92

21.1 REPLACEMENT ELECTRODE FOR WATER DISINFECTION

EQUIPMENT USING SILVER IONIZATION

Supply and delivery of electrode assembly suitable for water disinfection equipmentusing silver ionization process using pure silver metal electrode and fixed on PVC/Nylon sheets and nuts with electrical leads for the following capacities. The supplyshould be with the quality test certificate from approved organisations.

Life of electrodes inmillion litre at dosage

Sl.No.

CapapcityLPH


1 1000 2318.00

2 2000 3864.003 3000 6 12 5893.00

4 5000 8 16 6547.00

5 10000 9 18 7200.006 15000 15 30 9821.00

7 25000 30 60 25872.00

8 50000 60 120 52365.009 100000 120 240 104730.00

10 200000 240 480 209459.00

11 300000 360 720 313598.0012 400000 480 960 418920.00

13 500000 600 1,200 523650.00

0.01mg/lt 0.005mg/lt



93

Sl.No. Capacity in litres per day Rate for 2020-21 in Rupees.

1 50000 48720.00

2 100000 61698.00

3 150000 83431.00

4 200000 95275.00

5 250000 115361.00

6 300000 127720.00

7 350000 143321.00

8 400000 150380.00

9 450000 159650.00

10 500000 161195.00

11 1000000 395417.00

12 2000000 580508.00

13 3000000 762200.00

14 4000000 937300.00

15 5000000 1044715.00

16 6000000 1356656.00

17 7000000 1461618.00

18 8000000 1614009.00

19 9000000 1792199.00

20 10000000 2032189.00



21.2 ELECTRO CHLORINATOR BASED ON COMMON SALT

Supply, Delivery, erection and commissioning of Batch type electro chlorinatorusing common salt as raw material, consisting of electrolyzers cell made of Titaniumwith coating mixed metal oxide such as Anabium, Cadmium, etc, capable of producingsodium hypochlorite solution within time span of 8 hours, having adjustable meteringcum dosing pump capable of dozing the prepared sodium hypochlorite solution inwater supply system with sensor having auto shut down when the storage of FRPtank gets empty. The storage vessel and electrolyzer tank (hypo processingtank)must be made of FRP tank coated inside with hypothalic - BIS standard,having capacity to store required quantity of hypochlotrite solution, water andcommon salt for electrolysis process respectively. The electrochlorinator musthave power source or control module for producing necessary DC current forelectrolyser process from 440v, 3 phase / single phase AC supply and must haveauto cut off after batch time of 8 hours. For all power connection, copper cablesshould be used.

94

22.0 PROVIDING EPOXY COATING TO REINFORCEMENT STEEL BARS

Rate forSl No. Description unit 2020-21

in Rupees.

Providing Fusion Bonded Epoxy coatingnot less than 175microns thickness andupto 300 microns to reinforcement ofall diameters as per IS 13620/1993including testing of coating atplant.The cost is inclusive of cost onaccount of careful handling, PVC coatedbinding wires, touchup material suppliedby coating agency, repair work, loading,unloading and strengthening of bentrods etc., complete as per specificationand as directed by the Engineer incharge.

a. for 8mm to 16mm MT 14861.70

b. for 20mm to 32mm MT 11267.55



95

23.0 MECHANICAL JOINT COLLARS AS PER IS

Sl No. Description Unit Rate for 2020-21 in Rupees.

Supply and Delivery of MJ

Collars.

1 100mm Each 2553.00

2 150mm Each 4061.00

3 200mm Each 5300.00

4 250mm Each 7378.00

5 300mm Each 9578.00

6 350mm Each 13674.00

7 400mm Each 16288.00

8 450mm Each 18840.00

9 500mm Each 24051.00

10 600mm Each 30691.00



96

24.0 STAINLESS STEEL CLAMP

Supply and delivery of Leak Arresting Flexible SS Clamps of Wrap Around Single Sectiontype upto 500 mm diameter and Maxi Range double section type beyond 500 mm OD ofall rigid pipe sections. The Clamps made of stainless steel SS304 metallic body of 0.8 to1.0mm maximum thickness pasted with Waffle gaskets of Natural / Nitrile / EPDM grade(BS EN681-1) and fitted with self stabilizing Finger type clamps of 200 mm length SGgrade malleable cast iron duly powder coated (BS 2789 grade 400/12) and connectedthrough fasteners of EN8 material with Zinc Coating (BS 970). Suitable width of theclamps to be decided by the engineer incharge at site depending on the nature of pipecrack.

Sl No. Description Unit

Rate for 2020-21 in Rupees.

400 MM 600 MM 800 MM 1000MM 1200 MMWidth Width Width Width Width

I Suitable for AC Pipes

Class 10

1 100NB 1No. 4830 7935 10580 13230 158702 150NB 1No. 5880 9660 12880 16100 193203 200NB 1No. 6825 11215 14950 18690 224304 250NB 1No. 7718 12680 16910 21140 253605 300NB 1No. 8295 13630 18170 22720 272606 350NB 1No. 9135 15010 20010 29020 300207 400NB 1No. 9818 16130 21510 26890 322608 450NB 1No. 10920 17940 23920 29900 358809 500NB 1No. 12930 19400 25860 32330 38800

Class 15

1 100NB 1No. 5040 8280 11040 13800 165602 150NB 1No. 6090 10010 13340 16680 200103 200NB 1No. 7088 11650 15530 19410 232904 250NB 1No. 7928 13030 17370 21710 260505 300NB 1No. 8558 14060 18750 23440 281206 350NB 1No. 9345 15360 20470 25590 307107 400NB 1No. 10028 16480 21970 27460 329508 450NB 1No. 11235 18460 24610 30770 369209 500NB 1No. 13230 19850 26460 33100 39700

Class 20

1 100NB 1No. 5355 8800 11730 14670 176002 150NB 1No. 6300 10350 13800 17250 207003 200NB 1No. 7350 12080 16100 20130 241504 250NB 1No. 8190 13460 17940 22430 269105 300NB 1No. 8925 14670 19550 24440 293306 350NB 1No. 9555 15700 20930 26170 31400

97




7 400NB 1No. 10343 17000 22670 28320 33990

8 450NB 1No. 11550 18980 23300 31630 37950

9 500NB 1No. 13450 20200 26900 33630 40350

10 600NB 1No. - 27500 36700 45850 55000

11 700NB 1No. - 28500 38000 47500 72000II Suitable for Cast Iron or Ductile Iron Pipes

a Suitable for MS/CI/DI Pipes - Single section SS Clamp

1 4" Dia 1No. 4620 7590 10120 12650 15180

2 6" Dia 1No. 5460 8970 11960 14950 17940

3 8" Dia 1No. 6458 10610 14150 17690 212204 10" Dia 1No. 7455 12250 16330 20420 24500

5 12" Dia 1No. 7980 13110 17480 21850 26220

6 14" Dia 1No. 8820 14490 19320 24150 289807 16" Dia 1No. 9398 15440 20590 25740 30880

8 18" Dia 1No. 10238 16820 22430 28040 33640

9 20" Dia 1No. 11235 18460 24610 30770 36920b Suitable for MS/CI/DI Pipes - Double section SS Clamp

1 550 nb 1No. - 21840 33120 41400 496802 900 nb 1No. - 26220 34960 43700 52440

3 650 nb 1No. - 27140 36230 45260 54280

4 700 nb 1No. - 28520 38070 47560 570405 750 nb 1No. - 29440 39280 49110 58880

6 800 nb 1No. - 30480 40710 50830 60950

7 850 nb 1No. - 37950 50600 63250 759008 900 nb 1No. - 39100 52160 65210 78200

9 1000 nb 1No. - 42780 57040 71300 85560

10 1100 nb 1No. - 51750 69000 86250 10350011 1200 nb 1No. - 57500 76710 95860 115000III Suitable for PSC Pipes

a PSC Pipes - Wrap around single section

1 300 NB 1No. 9240 15180 20240 25300 30360

2 350 NB 1No. 10080 16560 22080 27600 33120

3 400 NB 1No. 10920 17940 23920 29900 35880

4 450 NB 1No. 11655 19150 25530 31920 38300

5 500 NB 1No. 12600 20700 27600 34500 41400

98

b PSC Pipes - Double section SS Clamp

1 600 nb 1No. - 28520 38070 47560 57040

2 700 nb 1No. - 29440 39280 49110 58880

3 800 nb 1No. - 33580 44850 56010 67160

4 900 nb 1No. - - 58650 73320 87930

5 1000 nb 1No. - - 64400 80500 96600

6 1100 nb 1No. - - 71300 89130 106950

7 1200 nb 1No. - - 80500 100630 120750

c PSC Pipes - Maxi RangeTriple section SS Clamp

1 1300 nb 1No. - - 96600 120750 144900

2 1400 nb 1No. - - 110000 137500 165000

3 1500 nb 1No. - - 124000 155000 186000

IV Suitable for HDPE Pipes

a Wrap around single section SS Clamp

1 110mmOD 1No. 4515 7420 9900 12380 14850

2 140mmOD 1No. 4935 8110 10820 13530 16230

3 160mmOD 1No. 5250 8690 11500 14380 17380

4 180mmOD 1No. 5775 9490 12600 15830 18890

5 200mmOD 1No. 6300 10350 13800 17250 20700

6 225mmOD 1No. 6825 11220 14960 18700 22440

7 250mmOD 1No. 7140 11730 15640 19550 23460

8 280mmOD 1No. 7613 12510 16680 20850 25020

9 315mmOD 1No. 7875 12940 17260 21575 25880

10 355mmOD 1No. 8400 13800 18400 23000 27600

11 400mmOD 1No. 8925 14670 19560 24450 29340

12 450mmOD 1No. 9975 16390 21860 27330 32780

13 500mmOD 1No. 10815 17770 23700 29630 35540

b Maxi Range Double section SS Clamp

1 566mmOD 1No. 15120 26340 35120 43900 52680

2 1000 mm OD 1No. - - 60000 75000 90000




Note : 1) The above rates are basic rates2) Transportation charges extra3) GST extra applicable as per GO

99

III (B) RATES FOR PUMP SETS

For individual specifications for various items regardingpump sets & Electrical Equipments, the specificationsalready given in the Manual for Pump sets should befollowed.

100

.

101

- Deleted-

1.0 CENTRIFUGAL MONOBLOCK PUMPSET AS PER IS9079/1989 WITHOUTPANEL BOARD THREE PHASE.Supply and delivery of Electric Monoset centrifugal pump conforming to IS9079:2002 as amended from time to time, with CI FG 200 Casing,hydraulically and dynamically balanced Bronze grade LTB-2 impeller, impellerring and casing ring, stainless steel shaft capable of discharging requiredquantity of water against a total head noted below due to all causes.Pump shall be of BEE 3 Star Rated and capable of discharging the specifiedquantity at the head noted at the minimum NPSHA at site conditions. Theshut off head shall be atleast 25% over and above the head at duty point.The pump shall be suitable for operation in AC three phase, 415 V+/- 10%,50 Hz +/- 5%. Squirrel cage induction motor for continuous operation. Thespeed of the Pump and Motor shall be not less than 2700 to 2900 RPMrespectively.

Sl.No. Duty Unit Rate for 2020-21lpmxm in Rupees

1 100x20 1 No 108352 150x20 1 No 159633 200x20 1 No 165874 250x20 1 No 183595 300x20 1 No 189856 350x20 1 No 189857 400x20 1 No 189858 450x20 1 No 189859 500x20 1 No 2201910 700x20 1 No 2372111 50x35 1 No 1722812 100x35 1 No 1957813 150x35 1 No 2367914 200x35 1 No 2665715 250x35 1 No 2995416 300x35 1 No 2995417 350x35 1 No 2995418 400x35 1 No 3005119 450x35 1 No 3005120 500x35 1 No 3005121 50x50 1 No 2665522 100x50 1 No 2995423 150x50 1 No 2995424 200x50 1 No 3202925 250x50 1 No 3202926 300x50 1 No 32029

Note: 1) The above rates are basic rates only.2) GST extra applicable as per GO.3) Duty of the Pumpset is the criteria for the rates.

102

2.0. SINGLE PHASE SUBMERSIBLE PUMPSET AS PER IS 8034/2002WITHOUT PANEL BOARDSupply and delivery of clear water vertical wet type submersible pumpconforming to IS 8034/2002 and as amended thereafter and BEE 3 StarRated capable of discharging noted LPM against head of water column dueto all causes. The pump shall be with stainless steel shaft and dynamicallybalanced bronze or Cast SS impeller, brass screws and CI FG 200 gradepump bowl/diffuser with ISI mark. The pump shall be directly coupled to acontinuous rated two pole suitable wet type vertical squirrel cage inductionmotor suitable for operation in AC single phase 230 V+/- 10%, 50HZ+/-5%


1 15x40 1 No 18419

2 15x50 1 No 18419

3 15x60 1 No 19151

4 15x70 1 No 22129

5 15x80 1 No 22129

6 15x90 1 No 22129

7 15x100 1 No 25245

8 15x125 1 No 28679

9 15X150 1 No 30874

10 20x40 1 No 19151

11 20x50 1 No 19151

12 20x60 1 No 19151

13 20x70 1 No 22129

14 20x80 1 No 22129

15 20x90 1 No 22539

16 20x100 1 No 26879

17 20X125 1 No 28679

18 20X150 1 No 30694


103

3.0. THREE PHASE SUBMERSIBLE PUMPSET SUITABLE FOR 100MM DIABOREWELL AS PER IS 8034/2002 WITHOUT PANEL BOARDSupply and delivery of clear water vertical wet type submersible pumpsuitable for 100mm dia borewell conforming to IS 8034/2002 as amendedthereafter and BEE 3 Star Rated capable of discharging noted LPM againsthead of water column due to all causes. The pump shall be with stainlesssteel shaft and dynamically balanced bronze or Cast SS impeller, brassscrews and CI FG 200 grade pump bowl/diffuser with ISI mark. The pumpshall be directly coupled to a continuos rated two pole suitable wet typevertical squirrel cage induction motor as per IS 9283 /1995 and as amendedthere after, suitable for operation in AC three phase 415 V+/- 10 %,50 HZ +/- 5 %


1 30x40 1 No 18753

2 30x50 1 No 18864

3 30x60 1 No 19746

4 30x70 1 No 20849

5 30x80 1 No 23828

6 30x90 1 No 25924

7 30x100 1 No 25924

8 30x125 1 No 28461

9 40x40 1 No 18643

10 40x50 1 No 19636

11 40x60 1 No 19636

12 40x70 1 No 25593

13 40x80 1 No 26696

14 40x90 1 No 28792

15 40x100 1 No 28792


104

3.1. THREE PHASE SUBMERSIBLE PUMPSET SUITABLE FOR 150MM DIABOREWELL AS PER IS 8034/2002 WITHOUT PANEL BOARDSupply and delivery of clear water vertical wet type submersible pumpsetsuitable for 150mm dia borewell conforming to IS 8034/2002 as amendedthereafter and BEE 3 Star Rated capable of discharging noted LPM againsthead of water column due to all causes. The pump shall be with stainlesssteel shaft and dynamically balanced bronze or Cast SS impeller, brassscrews and CI FG 200 grade pump bowl/diffuser with ISI mark. The pumpshall be directly coupled to a continuous rated two pole suitable wet typevertical squirrel cage induction motor as per IS 9283 /1995 as amendedthere after, suitable for operation in AC three phase 415 V+/-10%, 50HZ+/- 5 %

Duty Rate forSl.No. lpm x m Unit 2020-21

in Rupees

1 50x40 1 No 26272

2 50x50 1 No 28950

3 50x60 1 No 29567

4 50X75 1 No 32380

5 50x100 1 No 39650

6 50x125 1 No 42351

7 50x175 1 No 53770

8 50x200 1 No 59600

9 50x225 1 No 64169

10 50x250 1 No 75683

11 50x275 1 No 82629

12 75x40 1 No 28050

13 75x50 1 No 28950

14 75x60 1 No 30373

15 75x75 1 No 34635

16 75x100 1 No 42308

17 75x125 1 No 44844

18 75x150 1 No 53530

19 75x175 1 No 53530

20 75x200 1 No 58543

21 75x225 1 No 61621

22 75x250 1 No 75683

23 75x275 1 No 82629

24 100x30 1 No 26272

105

25 100x40 1 No 28050

26 100x50 1 No 30670

27 100x60 1 No 32380

28 100x75 1 No 38180

29 100x100 1 No 45148

30 100x125 1 No 51866

31 100x175 1 No 51866

32 100x200 1 No 56608

33 100x225 1 No 73723

34 100x250 1 No 82629

35 125x25 1 No 26526

36 125x40 1 No 28050

37 125x50 1 No 30480

38 125x60 1 No 33723

39 125x75 1 No 35614

40 125x100 1 No 43264

41 125x125 1 No 48747

42 125x200 1 No 66322

43 125x225 1 No 70532

44 150x25 1 No 26526

45 150x40 1 No 28050

46 150x50 1 No 28950

47 150x60 1 No 33723

48 150x75 1 No 37441

49 150x100 1 No 43992

50 150x125 1 No 48681

51 175x40 1 No 28050

52 175x50 1 No 33533

53 175x60 1 No 34487

54 175x75 1 No 34487

55 175x100 1 No 41192

56 200x25 1 No 26526

57 200x40 1 No 28050

58 200x50 1 No 32439


in Rupees

106

59 200x60 1 No 38180

60 200x75 1 No 38180

61 200x100 1 No 48318

62 200x125 1 No 55661

63 250x40 1 No 28050

64 250x50 1 No 34487

65 250x60 1 No 35048

66 250x75 1 No 45709

67 250x100 1 No 55663

68 250x125 1 No 65046

69 300x40 1 No 30295

70 300x50 1 No 35339

71 300x60 1 No 47600

72 300x75 1 No 53048

73 300x100 1 No 56245

74 350x40 1 No 35339

75 350x50 1 No 39883

76 350x60 1 No 47600

77 350x75 1 No 55661

78 350x100 1 No 61996

79 400x40 1 No 41741

80 400x50 1 No 50501

81 400x60 1 No 49027

82 400x75 1 No 65334

83 500x40 1 No 44755

84 500x50 1 No 49027

85 500x75 1 No 65334

86 600x40 1 No 46294

87 600x50 1 No 62388

88 600x75 1 No 71881



in Rupees

107

4.0 OPENWELL SUBMERSIBLE PUMPSET AS PER IS 14220/2002 WITHOUTPANEL BOARDSupply and delivery of Open well Submersible pump set conforming to IS14220 /2002 and as amended thereafter and BEE 3 Star Rated capable ofdischarging the following duties due to all causes. The pump shall be withstainless steel shaft and dynamically balanced bronze mixed type impeller, CIFG 200 grade casing and brass screws and rotor shall be of copper rod as perIS 613/1984 with ISI mark. The pump suitable for installation in sump with1.1KV grade 3 core suitable copper flat submersible cable to a length of 15mwith necessary cable joints. The non-return valve located at the top of thepump in the discharge outlet connection is to be designed with minimumfriction. The pump should be directly coupled to 2880 RPM, three phase, 50Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable forDOL upto 5 HP , Fully Automatic Air break Star Delta up to 20 HP and AutoTransformer starter for above 20 HP starting and for continuous operation.


in Rupees

1 50x25 1 No 22832

2 50x40 1 No 22864

3 50x50 1 No 27112

4 50x60 1 No 33909

5 50x75 1 No 45979

6 50x100 1 No 46523

7 50x125 1 No 73249

8 75x25 1 No 22864

9 75x40 1 No 25637

10 75x50 1 No 29046

11 75x60 1 No 33910

12 75x75 1 No 45979

13 75x100 1 No 46525

14 75x125 1 No 68562

15 75x150 1 No 92422

16 100x25 1 No 24713

17 100x40 1 No 29046

18 100x50 1 No 30532

19 100x60 1 No 45980

20 100x75 1 No 46524

21 100x100 1 No 46524

22 100x125 1 No 73361

23 125x25 1 No 25379

108

24 125x40 1 No 30478

25 125x50 1 No 35916

26 125x75 1 No 45980

27 125x100 1 No 46524

28 125x125 1 No 73361

29 150x25 1 No 25966

30 150x40 1 No 30478

31 150x50 1 No 30532

32 150x60 1 No 45979

33 150x75 1 No 45979

34 150x100 1 No 46525

35 150x125 1 No 77905

36 175x25 1 No 25606

37 175x40 1 No 30478

38 175x50 1 No 35916

39 175x60 1 No 45980

40 175x75 1 No 45980

41 175x100 1 No 63498

42 200x25 1 No 25606

43 200x40 1 No 30478

44 200x50 1 No 30532

45 200x60 1 No 45980

46 200x75 1 No 50532

47 200x100 1 No 63498

48 200x125 1 No 92204

49 250x25 1 No 25966

50 250x40 1 No 30532

51 250x50 1 No 37775

52 250x60 1 No 45980

53 250x75 1 No 63498

54 250x100 1 No 67253

55 250x125 1 No 87609


in Rupees

109

56 300x25 1 No 25966

57 300x40 1 No 30532

58 300x50 1 No 35916

59 300x60 1 No 50532

60 300x75 1 No 63498

61 300x100 1 No 67253

62 350x25 1 No 27985

63 350x40 1 No 41421

64 350x50 1 No 44673

65 350x60 1 No 51958

66 350x75 1 No 63498

67 350x100 1 No 67253

68 400x25 1 No 30532

69 400x40 1 No 41586

70 400x50 1 No 44673

71 400x60 1 No 53428

72 400x75 1 No 66051

73 500x25 1 No 30532

74 500x40 1 No 41586

75 500x50 1 No 44673

76 500x75 1 No 66758

77 600x25 1 No 30478

78 600x40 1 No 45524

79 600x50 1 No 54445

80 600x75 1 No 66758

81 700x40 1 No 50882

82 700x60 1 No 68534

83 700x80 1 No 68534

84 700x100 1 No 68534

85 800x40 1 No 50882

86 800x60 1 No 68534

87 800x80 1 No 68534


in Rupees

110


in Rupees

88 800x100 1 No 68534

89 900x40 1 No 68534

90 900x60 1 No 68534

91 900x80 1 No 68534

92 900x100 1 No 68534

93 1000x40 1 No 77611

94 1000x60 1 No 77611

95 1000x80 1 No 91805

96 1000x100 1 No 147189

97 1250x40 1 No 87744

98 1250x60 1 No 104620

99 1250x80 1 No 163443

100 1250x100 1 No 163443

101 1500x40 1 No 99100

102 1500x60 1 No 144777

103 1500x80 1 No 169204

104 1500x100 1 No 211063

105 2000x40 1 No 117114

106 2000x60 1 No 169204

107 2000x80 1 No 169204

108 2000x100 1 No 169204

109 2500x40 1 No 165161

Note: 1) The above rates are basic rates only.


3) Duty of the Pumpset is the criteria for the rates.

111

5.0

.RA

TES

FO

R H

OR

IZO

NTA

L S

PLIT

CA

SIN

G C

EN

TR

IFU

GA

L P

UM

P (

15

00

RP

M)

con

form

ing

to I

S 1

52

0Sup

ply

and

deliv

ery

of H

oriz

onta

l spl

it c

asin

g ce

ntri

fuga

l pum

p co

nfor

min

g to

IS 1

520

and

as a

men

ded

ther

eaft

er w

ith

CI

casi

ngan

d sp

lit g

land

s, s

tain

less

ste

el s

haft

, hyd

raul

ical

ly a

nd d

ynam

ical

ly b

alan

ced

bro

nze

impe

llers

cap

able

of d

isch

argi

ng r

equi

red

quan

tity

of

wat

er a

gain

st a

tot

al h

ead

note

d be

low

due

to

all ca

uses

and

wit

h th

e ac

cess

orie

s su

ch a

s G

.M a

ir r

elea

se c

ock,

Gre

ase

cup,

G.I

pri

min

g fu

nnel

, M

.S li

ftin

g ho

ok, dr

ip w

ater

G.I

pip

e co

nnec

tion

s, le

adin

g to

the

out

side

of p

ump

hous

e ru

bber

wat

er d

efle

ctor

, do

uble

fla

p fo

ot v

alve

, G

.M s

trai

ner

incl

udin

g un

ique

tyr

e ty

pe c

oupl

ing,

com

mon

M.S

fab

rica

ted

base

to

mou

nt p

ump

and

mot

or a

nd o

ther

sta

ndar

d fit

ting

s et

c co

mpl

ete.

Pum

p sh

all b

e ca

pabl

e of

dis

char

ging

the

spe

cifie

d qu

anti

tyat

the

hea

d no

ted

at t

he m

inim

um N

PSH

at

site

con

diti

ons.

The

shu

t of

f he

ad s

hall

be a

tlea

st 2

5% o

ver

and

abov

e th

e he

ad a

tdu

ty p

oint

. Th

e pu

mp

shal

l be

suit

able

for

ope

rati

on in

AC

thr

ee p

hase

, 4

15 V

, 5

0 H

z ,

1500

RPM

.

Rate

fo

r 2

02

0-2

1 in

Ru

pees

Rs.

in

Lakh

s.S

l.N

o.

Ca

pa

cit

y in

LP

MH

ea

d in

Metr

es

25

30

35

40

45

50

55

60

70

80

90

115

003.

273.

123.

793.

853.

884.

674.

954.

965.

285.

285.

882

2500

3.27

3.27

3.89

4.01

4.78

4.78

5.02

5.31

5.93

6.15

6.15

330

003.

273.

274.

094.

155.

025.

024.

785.

316.

346.

346.

404

3500

3.27

3.27

4.09

4.15

5.02

5.74

6.19

6.51

6.77

6.77

6.77

540

003.

783.

784.

154.

155.

095.

816.

466.

626.

776.

776.

776

5000

4.13

4.13

4.24

4.37

5.91

6.16

6.74

6.97

7.19

7.23

7.24

760

004.

134.

135.

735.

866.

216.

647.

047.

828.

188.

338.

618

7000

5.28

5.61

5.81

6.03

6.50

6.77

7.27

7.98

8.23

9.19

9.37

980

005.

435.

615.

866.

466.

777.

127.

277.

6311

.90

12.1

912

.79

1090

005.

435.

816.

016.

776.

977.

127.

277.

3812

.47

13.6

614

.71

1110

000

5.43

5.81

6.08

6.80

7.14

7.43

7.43

12.8

916

.48

17.1

717

.28

1215

000

6.68

6.88

6.71

8.26

8.67

9.13

10.7

414

.25

17.1

517

.15

17.2

813

2000

07.

347.

487.

4914

.51

14.9

116

.37

18.6

818

.68

19.0

819

.19

19.7

114

2500

016

.90

17.1

717

.65

17.9

018

.35

18.3

819

.11

19.1

119

.71

20.1

320

.06

1530

000

18.2

818

.97

19.8

720

.17

20.3

520

.94

20.8

723

.83

26.9

027

.88

28.6

6

Not

e:1)

The

abov

e ra

tes

are

basi

c ra

tes

incl

usiv

e of

MS b

ase

plat

e, fle

xibl

e ty

re c

oupl

ing

and

foun

datio

n bo

lts.

2)G

ST

extr

a ap

plic

able

as

per

GO

3)Ef

ficie

ncy

may

be

take

n fr

om u

nive

rsal

cur

ve fo

r ca

lcul

atio

n of

mot

or H

P, o

ther

wis

e m

anuf

actu

rers

may

be

cons

ulte

dfo

r ef

ficie

ncy

curv

e.4)

NPS

H req

uire

men

t sho

uld

be a

sses

sed

and

sum

p sh

ould

be

desi

gned

acc

ordi

ngly

.

112

6.0. HORIZONTAL SQUIRREL CAGE MOTOR 1500 RPM

AC three Phase /415 V/ Horizontal SPDP 4 Pole Squirrel cageInduction motor for HSC Centrifugal pumps

Supply and delivery of AC three Phase 4 pole Horizontal squirrel cage Inductionmotor confirming to IS 325/1996 and as amended thereafter with Class F insulationto suit the speed of pump and suitable for operation with continuous S1 rated,415V +/- 10 %, 50 HZ +/- 5% supply , TEFC (upto 20 HP), SPDP (above 20 HP).The motor offered should be of energy efficient motors.

Sl.No KW HP Rate for 2020-21in Rupees

1 9.3 12.5 92480

2 11 15 98179

3 15 20 115635

4 18.5 25 157956

5 22 30 173463

6 30 40 196308

7 37 50 246040

8 45 60 297607

9 55 75 303784

10 75 110 461341

11 90 120 486056

12 110 150 606470

13 125 170 780573

14 132 180 825882

15 150 200 833092

16 160 215 908265

17 180 240 908265

18 187 250 945337

19 200 270 1015362

20 220 300 1334594

21 250 335 1519535

22 280 375 2096630

23 300 400 2419981

Note: 1) The above rates are basic rates inclusive of handling charges.


113

7.0. HORIZONTAL SQUIRREL CAGE MOTOR 1000 RPM

AC three Phase /415 V/ Horizontal SPDP 6 Pole Squirrel cage Inductionmotor for HSC Centrifugal pumps

Supply and delivery of AC three Phase 6 pole Horizontal squirrel cage Inductionmotor confirming to IS 325/1996 and as amended thereafter with Class F insulationto suit the speed of pump and suitable for operation with continuous S1 rated,415 V +/- 10 %, 50 HZ +/- 5% supply , TEFC (upto 20 HP), SPDP (above 20 HP).The motor offered should be of energy efficient motors.


1 9.3 12.5 89735

2 11 15 94295

3 15 20 132893

4 18.5 25 156944

5 22 30 202011

6 30 40 251978

7 37 50 314959

8 45 60 387994

9 55 75 444509

10 75 110 533542

11 90 120 605219

12 110 150 777594

13 125 170 925170

14 132 180 925170

15 150 200 987568

16 160 215 1065056

17 180 240 1490535

18 187 250 1514376

19 200 270 1639121

20 220 300 1880702

21 250 335 2105450



114

8.0

.V

ER

TIC

AL T

UR

BIN

E P

UM

P (

WA

TE

R L

UB

RIC

ATE

D)

CO

NFIR

MIN

G T

O I

S1

71

0/

19

89

(R

EA

FFIR

ME

D 2

00

9)

15

00

RP

M S

UIT

AB

LE F

OR

VER

TIC

AL H

OLLO

W S

HA

FT S

QU

IRR

EL C

AG

ESup

ply

and

deliv

ery

of V

ertica

l wat

er/o

il lu

bric

ated

sta

tica

lly,

dyna

mic

ally

, hy

drau

lical

ly b

alan

ced

turb

ine

pum

pca

pabl

e of

dis

char

ging

the

follo

win

g d

uty

cond

itio

n as

giv

en b

elow

due

to

all c

ause

s w

ith

surf

ace

disc

harg

e he

adco

nfir

min

g to

IS 1

710

and

as a

men

ded

as o

n da

te w

ith

acce

ssor

ies

as

per

IS 5

120/

1977

( R

eaff

irm

ed 2

011

) an

das

am

ende

d th

erea

fter

to

suit t

he s

ite

cond

itio

n.

The

spee

d, N

umbe

r of

sta

ges,

siz

es o

f co

lum

n pi

pes

and

line

shaf

t in

dica

ted

is b

ased

on

site

con

dition

pre

vaili

ng d

urin

g in

vest

igat

ion.

The

pum

p sh

ould

be

supp

lied

with

non

reve

rsib

le r

atch

et p

in h

ousi

ng s

afet

y cl

utch

, su

ctio

n st

rain

er e

tc.

The

Pum

p Bow

l ass

embl

y sh

all b

e w

ith

bron

zeim

pelle

r ru

nnin

g at

145

0 RPM

. The

pum

p in

clud

es s

uita

ble

head

sha

ft, s

uita

ble

1.5

met

re lo

ng S

S li

ne s

haft

req

uire

dN

os. to

sui

t th

e w

ell d

epth

, Rub

ber

line

shaf

t be

arin

g of

req

uire

d N

os.,

C.I

Bea

ring

ret

aine

r of

req

uire

d N

os.,

100

litre

HD

PE P

re-

lubr

icat

ing

tank

with

20m

m P

VC R

igid

pip

e co

nnec

tion

alo

ng w

ith

GM

gat

e va

lves

, Sui

tabl

e ER

Wco

lum

n pi

pe o

f ea

ch 1

.5m

long

of re

quir

ed N

os.

to s

uit

the

wel

l dep

th,

Suc

tion

bel

l mou

th o

f su

itab

le s

ize,

M

.S.

clam

ps s

uita

ble

for

colu

mn

pipe

/lin

e sh

aft

-2 s

et a

nd S

pann

er -

1 s

et e

tc c

ompl

ete

Rate

fo

r 2

02

0-2

1 in

Ru

pees

Rs.

in

Lakh

s.S

l.N

o.

Ca

pa

cit

y in

LP

MH

ea

d in

Metr

es

15

m2

0m

30

m4

0m

50

m6

0m

70

m8

0m

90

m1

00

m1

1500

3.21

3.21

3.43

3.43

3.56

3.65

3.86

3.86

4.27

4.49

220

006.

436.

807.

618.

449.

4110

.05

10.4

710

.68

10.8

911

.65

330

008.

308.

499.

0010

.01

11.0

811

.53

11.9

811

.98

11.9

812

.04

440

009.

089.

3911

.68

11.8

712

.04

12.0

412

.42

13.2

213

.59

13.5

95

5000

10.9

711

.29

11.8

712

.68

13.0

913

.41

13.9

714

.19

14.3

914

.78

660

0011

.29

11.2

912

.03

12.6

413

.41

13.4

113

.97

14.1

914

.40

14.7

87

7000

11.2

911

.29

12.0

312

.64

13.4

113

.41

14.4

014

.40

14.4

014

.78

880

0012

.63

12.2

712

.64

13.2

313

.59

13.5

914

.40

14.4

014

.40

14.7

89

1000

012

.03

12.2

712

.75

13.2

313

.59

13.9

714

.40

14.4

014

.78

14.7

810

1500

013

.19

13.4

913

.59

13.9

714

.86

14.7

815

.15

15.9

516

.31

16.6

911

2000

015

.01

15.4

916

.12

16.7

217

.14

19.1

621

.07

21.4

824

.76

29.8

112

2500

015

.43

15.9

216

.52

17.0

317

.54

19.5

321

.48

21.9

825

.26

30.7

213

3000

026

.45

27.7

028

.72

30.6

530

.95

32.6

032

.99

36.6

837

.13

41.0

6

Not

e:1)

The

abov

e ra

tes

are

basi

c ra

tes

incl

usiv

e of

tra

nspo

rtat

ion

and

hand

ling

char

ges

2)G

ST

extr

a ap

plic

able

as

per

GO

3)M

ultipl

y w

ith

1.15

for

oil l

ubri

cate

d pu

mps

(fo

r ra

w w

ater

)4)

Rate

s gi

ven

are

with

sus

pens

ion

leng

th o

f 7m

, bro

nze

impe

ller,

SS 4

01 s

haft

, MS c

olum

n pi

pe,

disc

harg

e ca

se &

CI

bell

mou

th.

5)Add

7.5

% e

xtra

for

each

1.5

m le

ngth

col

umn

pipe

ass

embl

y in

the

abo

ve r

ate.

115

9.0 VERTICAL HOLLOW / SOLID SHAFT MOTORS FOR TURBINE PUMP

AC three Phase /415 V/ Vertical Hollow / Solid Shaft TEFC & SPDP 4 PoleSquirrel cage Induction Motor 1500RPM

Supply and delivery of vertical Hollow / Solid shaft Squirrel cage induction motor(IS 325 ) suitable for the above pump continuous rated TEFC/SPDP type with Class ‘F’insulation for operation in AC, three Phase/50 HZ (±5%), 415V (±10%) running with aspeed of pump noted above and with inbuilt thrust bearing assembly capable of takingup the entire load and non - reverse ratchet assembly etc., complete. The motorrating noted above is the minimum and shall be such that it should never be overloaded when the pump works at MWL condition and shall be 10% over and above themaximum HP absorbed by the pump. The motor offered should be energy efficientmotors to have maximum efficiency at high power factor. Separate thrust bearingassembly could also be supplied to take up the down load.


TEFC MOTORS

1 18.5 25 1111742 22 30 1222943 30 40 1414864 37 50 1851925 45 60 223750

SPDP MOTORS

6 55 75 3503177 75 100 4622348 90 120 4820869 110 150 62122210 125 170 64199911 132 180 71991112 150 200 81101313 160 215 97442414 180 240 101597715 187 250 102325016 200 270 113232717 220 300 118426918 250 335 126737619 280 375 148111120 300 400 167909121 380 520 185465822 400 540 2194585

Note: 1) The above rates are basic rates inclusive of handling charges.2) GST extra applicable as per GO

116

10.0 Iron core Oil Cooled Transformer with Copper Winding Conformingto IS 1180 (Part 1) of 2014.Supply and delivery of 11 KV/433 Volts, 22 KV/433 Volts and 11 /22 KV/433 Volts, three Phase 50 Hz double wound oil immersed natural air cooled,core type continous rating, outdoor distribution power transformer withcopper winding for voltage ratio 22-11 KV/433 volts between phases withneutral brought out at LV side. The transfer shall be contained in a mildsteel plain & radiator cooled tank, conforming to IS 1180 (Part I) of 2014.with off-load tap switch for ±10% on LV side and ±5 % on H.V.side. Thetransformer shall be supplied with first filling of oil and consisting of all thefittings and accessories such as Inspection cover,Oil level indicator withminimum and filling level markings, Externally operated off circuit tapchanging switch with locking device & keys, H.V. Terminals- Bushings, L.V.Terminals cable box Rating plate, Two earthing terminals, two lifting hooksetc complete as per IS 1180 (Part I) of 2014 and as amended thereafter.

Sl.No Rating in KVA Rate for 2020-21 in Rupees

11KV/433V 22 KV/433 V 11KV/22KV

/433V

1 63 172763 183560 205157

2 100 199181 209664 230630

3 150 353443 374320 430468

4 160 291538 318532 345527

5 200 323930 318532 345527

6 250 394676 453503 485897

7 315 464300 496694 539885

8 400 518290 572278 626267

9 500 597542 642968 712856

10 630 670924 712856 796722

11 750 796722 824678 985420

12 800 824678 859621 1031545

13 1000 922520 964453 1157344

Note : 1) The above rates are basic rates inclusive of transportation andhandling charges.


117

11.0. SINGLE PHASE PANEL BOARD WITH TWO LEVEL GUARD AND AUTO STARTSupply and delivery of direct online starter confirming to IS13947,IEC60947-1 suitable KW rating for operation in AC/single Phase/50Hz(± 5%)and 230 V(±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16amps 2 pole Magnetic Contactor with under Voltage protection, Indicationlamp, starting capacitor, running capacitor and On/Off Push button switches,5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulatedcable, powder coated vermin proof box including the capacitor (the cost ofcapacitor is to be taken separately).

Sl. No. HP Unit Rate for 2020-21 in Rupees

1 1 1 No. 5544.00

2 1.5 1 No 5775.00

3 2 1 No 6695.00

Note: 1) The rate are basic rates inclusive of two level guard worth Rs.550/- andauto start facility worth Rs. 400/-

2) Timer is not recommended for this panel board.3) Panel board should be provided as per specification given in Board circular

No. 23/DCE/QATA/2004/Dt. 23.8.20044) GST extra applicable as per GO

11.1. THREE PHASE PANEL BOARD- D.O.L. WITH TWO LEVEL GUARD AND AUTO STARTSupply and delivery of direct online starter confirming to IS13947,IEC 60947-1 suitable KW rating for operation in AC/three Phase/50HZ(± 5%)and 415 V(±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16amps 2 pole Magnetic Contactor with under Voltage protection, Indicationlamp, starting capacitor, running capacitor and On/Off Push button switches,5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulatedcable, powder coated vermin proof box including the capacitor (the cost ofcapacitor is to be taken separately).


1 1 1 No. 13006.00

2 2 1 No 13006.00

3 3 1 No 13283.00

4 4 1 No. 13283.00

5 5 1 No 13656.00

6 6 1 No 13656.00

Note : 1) The rate are basic rates inclusive of two level guard worth Rs.550/- andauto start facility worth Rs. 400/-

2) For Timer facility if necessary Rs.4000/- may be added as extra.3) Panel board should be provided as per specification given in Board circular

No. 23/DCE/QATA/2004/Dt. 23.8.20044) GST extra applicable as per GO5) DOC starters are to be adopted upto 6 HP

118

11.2 THREE PHASE PANEL BOARD-STAR DELTA WITH TWO LEVEL GUARD ANDAUTO STARTSupply and delivery of Star-Delta starter confirming to IS13947,IEC 60947-1 suitable KW rating for operation in AC/ three Phase/50Hz(+/- 5%) and 415V (+/- 10%) including 3 pole magnetic contactor with undervoltage release - 3 nos., CT operated Ammeter(65 mm dia) with suppressedscale, Voltmeter (65mm dia), Voltmeter selector switch, Minature circuit breaker,Thermal Overload relay, Air Break contactors suitable for next Standardhigher KW rating, Single phasing preventor, dry running preventor and On/OffPush button switches, wiring with 1 sq.mm/4 sq. mm copper pvc insulatedcable, powder coated vermin proof box, including the capacitor(the cost ofcapacitor is to be taken separately).


1 6 1 No. 16354

2 7.5 1 No 17170

3 10 1 No 20797

4 12.5 1 No. 21665

5 15 1 No 22557

6 20 1 No 22557

7 25 1 No 22557

Note : 1) The rate are basic rates inclusive of two level guard worth Rs.550/- andauto start facility worth Rs. 400/-

2) For Timer facility if necessory Rs. 4000/- may be added as extra.3) Panel board should be provided as per specification given in Board circular

No. 23/DCE/QATA/2004/Dt. 23.8.20044) Air break fully automatic star delta starters are suggested for above 6 HP

upto 20HP except submersible pumpsets for which fully automatic ATSstarters are to be adopted


11.3 DOL STARTER WITH SINGLE PHASING PREVENTOR WITH ANALOG AMMETERAND VOLTMETER CONFORMING TO IS13947, IEC60947-1 WITH AUTORESTART FACILITY FOR PUMP HOUSES WHERE PANEL BOARDS AREAVAILABLE

Supply and delivery of direct online starter confirming to IS13947,ICE 60947-1 suitable KW rating for operation in AC/ three Phase/50HZ(+/- 5%) and 415V (+/- 10%) including Ammeter, Overload relay, underVoltage release with no Volt coil, Air Break contactors suitable for nextStandard higher KW rating, Single phase preventor, dry running preventorand On/Off Push button switches, including the capacitor(the cost ofcapacitor is to be taken separately).

Upto 5 HP - Rs. 4947/- each.

Note : 1) The above rate is basic rate only. 2) GST extra applicable as per GO

119

11.4 FLEX COMPENSATED MAGNETIC AMPLIFIER SOFT STARTER SUITABLEFOR L.T.SQUIRREL CAGE MOTOR

Supply and delivery of floor mounted type FCMA Air/ Oil Cooled soft startersuitable for the LT motor offered for operation in AC three Phase 50Hz(+/- 5%), 415V(+/-10%) including line contactors suitable for next standardhigher KW rating, Over load relay, instrument panel with frequency meter,Ammeter, Voltmeter, indicating lamp 6Nos, LED ON/OFF type and Start /Stop push button.

Sl. No. KW Unit Rate for 2020-21 in Rupees

1 30 to 37 1 No 180073

2 38 to 75 1 No 321048

3 76 to 135 1 No 447612

4 136 to 160 1 No 506268

5 161 to 250 1 No 756316

6 251 to 300 1 No 886998

7 301 to 500 1 No 1247446

8 501 to 750 1 No 1635081

Note: 1) The above rates are basic rates only

2) FCMA soft starter are to be adopted for 100 HP and above.


120

11.5 FLEX COMPENSATED MAGNETIC AMPLIFIER SOFT STARTER SUITABLEFOR H.T.SQUIRREL CAGE MOTOR

Supply and delivery of suitable KW indoor automatic air cooled dust andvermin proof FCMA Soft Starter for the operation in 3.3 KV three Phase50 Hz, AC supply termination with phase segregated neutral terminal boxof the motor , housed in 14 SWG sheet steel enclosure, painted withepoxy or polyurethene , 230V AC 10 Amps control supply , Class B insulation,300 mm height fabricated pedastal (to prevent water ingress for starterpanel) and condensation heater with switch with thermostat, interlockingwith running motor with built in facility for run mode/by pass etc. complete.The starter may be provided with contactors suitable for next standardhigher KW rating, Over load relay, instrument panel with frequency meter,Ammeter, Voltmeter, indicating lamp 6 Nos, LED ON/OFF type and Start /Stop push button.

Sl. No. KW Unit Rate for 2020-21 in Rupees

1 250 1 No 722693

2 300 1 No 761210

3 350 1 No 818277

4 400 1 No 856491

5 500 1 No 893975

6 600 1 No 1005361

7 700 1 No 1106311

8 800 1 No 1236512

9 900 1 No 1341490

10 1000 1 No 1467428

Note: 1) The above rates are basic rates only

2) FCMA soft starter are to be adopted for 100 HP and above.


121

11.6 FULLY AUTOMATIC AIR BREAK STAR DELTA STARTER WITH SINGLE PHASEPREVENTOR WITH AMMETER CONFIRMING TO IS13947, IEC 60947-1 WITHAUTO RESTART FACILITY FOR PUMP HOUSES WHERE PANEL BOARDS AREAVAILABLE

Supply and delivery of Star-Delta starter where panel boards are availableconfirming to IS13947, IEC 60947-1 suitable KW rating for operation in AC/three Phase/50Hz(+/- 5%) and 415V (+/-10%) including 3 pole magneticcontactor with under voltage release - 3 Nos., CT operated Ammeter(65 mmdia) with suppressed scale, Voltmeter (65mm dia), Voltmeter selector switch,Minature circuit breaker, Thermal Overload relay, Air Break contactors suitablefor next Standard higher KW rating, Single phasing preventor, dry runningpreventor and On/Off Push button switches, wiring with 1 sq.mm/4 sq. mmcopper pvc insulated cable, powder coated vermin proof box, including thecapacitor(the cost of capacitor is to be taken separately).

Sl. No. KW Rating HP Unit Rate for 2020-21 in Rupees

1 7.5 10 1 No 16441

2 11 15 1 No 16441

3 15 20 1 No 17728

4 18.5 25 1 No 17728

5 22 30 1 No 28934

6 30 40 1 No 33143

7 37 50 1 No 37798



3) Air break fully automatic star delta starters are suggested for above 6HP upto 20HP except submersible pumpsets for which fully automaticATS starters are to be adopted

122

11.7 FULLY AUTOMATIC AIR BREAK AUTO TRANSFORMER STARTER WITHSINGLE PHASING PREVENTOR WITH AMMETER CONFIRMING TO IS 8544PART IV WITH AUTO RESTART FACILITYSupply and delivery of Fully Automatic Auto Transformer Starter suitablefor the motor offered. Floor mounting type air/ oil cooled Auto TransformerStarter with tapings at 50%, 65%, 80%, housed in robust steel chamberwith arc and main contacts confirming to IS 8544 Part IV and as amendedthereafter for operation in AC three Phase 50 Hz (+/- 5%), 415V (+/- 10%)with the following components etc. under voltage release with no voltcoil, over load relay with dash pot arrangements, single phasing preventor,LED ON/ OFF switches, Mounted Ammeter, Earth leakage relay, contactorassembly suitable for next standard KW rating, incoming and outgoingcable entry provisions, transformer tank including first filling of oil etc.

Sl.No. KW Rating HP Unit Rate for 2020-21 in Rupees

1 5.5 7.5 1 No 28851

2 7.5 10 1 No 28851

3 9 12.5 1 No 33187

4 11 15 1 No 34570

5 15 20 1 No 69140

6 22 30 1 No 88373

7 30 40 1 No 99414

8 37 50 1 No 114676

9 45 60 1 No 127985

10 60 80 1 No 177019

11 75 100 1 No 193934



3) Air break fully automatic star delta starters are suggested for above 6HP upto 20HP except submersible pumpsets for which fully automaticATS starters are to be adopted

123

12.0. L.T. CABLES 3,3.5,4 CORE 1.1 KV GRADE ARMOURED ALUMINIUMCONDUCTOR CROSS LINKED POLY ETHYLENE INSULATED PVC SHEATHEDCABLES CONFIRMING TO IS 7098 (PART I)/1988 AND AS AMENDEDTHEREAFTER WITH ISI MARKING

Sl.No Description UnitRate for 2020-21 in Rupees

3 Core 3.5 Core 4 Core

1 4sq.mm metre 74.00 _ 149.00

2 6sq.mm metre 90.00 _ 158.00

3 10sq.mm metre 101.00 _ 173.00

4 16sq.mm metre 106.00 _ 226.00

5 25sq.mm metre 133.00 276.00 _

6 35sq.mm metre 163.00 324.00 _

7 50sq.mm metre 216.00 424.00 _

8 70sq.mm metre 285.00 543.00 _

9 95sq.mm metre 373.00 701.00 _

10 120sq.mm metre 449.00 858.00 _

11 150sq.mm metre 547.00 1016.00 _

12 185sq.mm metre 675.00 1245.00 _

13 240sq.mm metre 852.00 1571.00 _

14 300sq.mm metre 1034.00 1928.00 _

15 400sq.mm metre 1324.00 2467.00 _

Note: 1) The above rates are basic rates only.2) GST extra applicable as per GO

124

12.1. PVC INSULATED AND SHEATHED 3 CORE FLAT TYPE COPPER CABLECONFIRMING TO IS 694/1990 AND AS AMENDED THEREAFTER.

Sl.No Description Unit Rate for 2020-21 in Rupees

1 1.5 sq.mm meter 71







8 35.0 sq.mm meter 1204

9 50.0 sq.mm meter 1687

10 70.0 sq.mm meter 2487

11 95.0 sq.mm meter 3028

Note: 1) The above rates are basic rates only.2) GST extra applicable as per GO

125

12.2 RATE FOR CABLE JOINTS INCLUDING JOINTING MATERIALS ANDLABOUR

I. JOINTING OF L.T.CABLES - 3,3.5,4 CORE 1.1 KV GRADEARMOURED ALUMINIUM CONDUCTOR CABLE CONFIRMING TO IS1554 AND AS AMENDED THEREAFTER PART I WITH ISI MARKING

Sl.No Description UnitRate for 2020-21 in Rupees

3 Core 3.5 Core 4 Core

1 4sq.mm metre 81 _ 163

2 6sq.mm metre 97 _ 171

3 10sq.mm metre 110 _ 188

4 16sq.mm metre 116 _ 247

5 25sq.mm metre 144 300 _

6 35sq.mm metre 178 353 _

7 50sq.mm metre 235 461 _

8 70sq.mm metre 311 591 _

9 95sq.mm metre 407 765 _

10 120sq.mm metre 490 935 _

11 150sq.mm metre 598 1105 _

12 185sq.mm metre 736 1356 _

13 240sq.mm metre 928 1713 _

14 300sq.mm metre 1127 2101 _

15 400sq.mm metre 1442 2689 _

126

II. JOINTING OF XLPE INSULATED AND SHEATHED 3 CORE FLAT TYPECOPPER CABLE CONFIRMING TO IS 694/1990 and as amendedthereafter


1 1.5 sq.mm metre 79







8 35.0 sq.mm metre 1307

9 50.0 sq.mm metre 1833

10 70.0 sq.mm metre 2703

11 95.0 sq.mm metre 3290

III. JOINTING OF HT CABLE -XLPE INSULATED ARMOURED ALUMINIUMCONDUCTOR CABLE


11KV 12KV

1 3 C 240 sq.mm metre 1407 1718

2 3 C 185 sq.mm metre 1172 1453

3 3 C 150 sq.mm metre 994 1292

4 3 C 120 sq.mm metre 884 1161

5 3 C 95 sq.mm metre 750 1052

6 3 C 70 sq.mm metre 672 927

127

12.3 CABLE LAYING


Sl.No Description Unit For laying below For laying inGL including trenches insideearth work in the pump room

Rupees or in air

1 up to 95 sq.mm Metre 155.00 100.00

2 95 to 240 sq.mm Metre 218.00 151.00

3 240 to 400 sq.mm Metre 316.00 248.00

12.4 CABLE CLAMPS


in Rupees

1 up to 95 sq.mm each 318.00

2 95 to 240 sq.mm each 396.00

3 240 to 400 sq.mm each 585.00

NOTE : 1) The above rates are basic rates only.


3) For every 3 metre length one set of clamp is to be provided

4) Suitable number of clamps are to be arrived at according to the length

5) Provision for cable trench and delivery pipe duct are to be provided in pumphouse detailed estimate.

128

H.T. CABLE

12.5. PVC INSULATED ARMOURED ALUMINIUM CONDUCTOR CABLE


11KV 12KV

1 3 C 240 sq.mm metre 1291 1577

2 3 C 185 sq.mm metre 1075 1334

3 3 C 150 sq.mm metre 913 1186

4 3 C 120 sq.mm metre 810 1065

5 3 C 95 sq.mm metre 688 966

6 3 C 70 sq.mm metre 616 850

Note: 1) The above rates are basic rates only.2) GST extra applicable as per GO.

13.0 VACCUM PUMP SET WITH ACCESSORIES

Sl. No. Description Unit Rate for 2020-21in Rupees

1 Price for 5 HP Model/Rotary typeVaccum pumpsets (Pumpset + GIPipes + Fittings + Starters + Valves+ 100 Lr.Tank) including Transportationand handling charges. 1 No 383167

2 Price for 10 HP Vaccum pumpsetwith all the above Accessories 1 No 494893

3 150mm dia Pressure Gauge and Vaccumguage including all accessories as perspecification (For Suction and Deliveryto be mounted on wall on Teak WoodBoard) 1 No 6855

NOTE : 1) The above rates are basic rates only.


129

14.0 MOULDED CASE CIRCUIT BREAKER(MCCB) WITH THERMO MAGNETICRELEASE

Sl.No. RangeRate for 2020-21 in Rupees

3POLE 4 POLE

1 32-100 9996 12376

2 125 13804 15232

3 160 16679 19992

4 200 28560 31682

5 250 28560 33321

6 320 36578 42353

7 400 38526 44268

8 630 42605 51340

9 800 57756 76956

10 1000 89820 115513

11 1250 101359 139943

12 1600 115454 174215

NOTE: 1) The above rates are basic rates inclusive of handling charges and F.O.Rdestination.

2) GST extra applicable as per GO3) The rate for MCB for single phase usage the PWD schedule of rates shall

be referred.4) Add 35% cost of MCCB/ACB/ MCB towards the cost of fabrication, other

fittings and labour5) Upto 15 KW distribution box shall be used. For more than one outgoing

loads PWD schedule of rates shall be referred.

15.0 RATE FOR MIXED DI ELECTRIC CAPACITOR WITH TNEB TEST

CERTIFICATE WITH ACCESSORIES INCLUDING BANKING CONFIRMING

TO IS 2834.

Rs.449/- per KVAR

Note: 1) The above rate is basic rate inclusive of handling charges.


3) The rate for mixed DI Electric Capacitor with Test Certificate given asRs.449/- per KVAR is inclusive of Banking charges, such as providing ofcopper bus bars with provision for adding atleast 2 capacitors at laterdate, cable entry box, fabricating charges etc. complete. This rate is notapplicable for replacement of capacitors which does not require bankingand fabrication works.

130

16.0 LT/LTCT METERING BOX as per IE rules and TANGEDCO norms

Rate forSl.No. Description Unit 2020-21

in Rupees

1 Up to 50HP/37 KW (which includes LT meterpanel board 6 Nos. suitable fuse carriers 1 No. 24740.00

2 75 HP/56 KW (which includes LT meter panelboard 6 Nos. suitable fuse carriers) 1 No. 32287.00

3 75HP-150HP/56-112 KW (which includesLTCT meter panel board 6 Nos. suitable fusecarriers and 3 Nos. CT Coil) 1 No. 40234.00

4 In HT supply using LTCT metering Box as perIE rules and TANGEDCO norms (Above 150 HPbelow 200 HP) 112-150 KW 1 No. 64974.00

Note : 1) The above rates are basic rates inclusive of handling charges.2) GST extra applicable as per GO

17.0 TRANSFORMER SUB STATION RELATED WORKS


in Rupees

1 Designing and preparation of CEIG drawings,obtaining Approval and safety certificateincluding submission of Completion report andrectification report. 1 No. 67353.00

2 Supply, delivery of 6 pole structure materialswith suitable Size RSJ along with all structurematerial are as under.

a For 11 KV Sub station 1 No. 342720.00

b For 22 KV Sub station 1 No. 456960.00

3 Construction of transformer plinth 1 No. 22848.00

4 Chain link fencing with gate including theTNEB 2 poles Spreading of materials as perCEIG requirements 1 No. 57120.00

5 Transformer yard earthing using copper flatand TWIN earthing as per IS

a Upto 250 KVA Transformer sub station 1 No. 34272.00

b Above 250 KVA 1 No. 68544.00

6 Transformer sub station erection charges 1 No. 21783.00

Note : 1) The above rates are basic rates inclusive of handling charges.2) GST extra applicable as per GO3) Provision for cement concrete flooring has to be made at the sub station

yard

131

17.1 AIR CIRCUIT BREAKER (With Shunt release and Under voltage release)

Sl.No. Range in AMPSRate for 2020-21 in Rupees

3POLE 4 POLE

1 630 126243 127257

2 800 156950 159069

3 1000 177872 219300

4 1250 188799 231270

5 1600 209516 269484

6 2000 247519 295120

7 2500 271320 323680

8 3200 356999 429352

9 4000 495880 595000

Note: 1) The above rates are basic rates inclusive of handling charges, F.O.Rdestination.


18.0 SAFETY APPLIANCES


in Rupees

1 Electrical gloves tested to 11 KV /22 KV withwooden box dusted with french chalk powder 1 No. 594

2 Electrical quality 6mm thick rubber mat 1 No. 649

3 5 kg capacity ISI marked Dry chemical powderfire extinguisher 1 No. 2318

4 Fire Bucket-3 Nos Hooked to MS stand 1 No. 926

5 Laminated shock treatment chart 1 No. 618

6 Wooden First Aid Box 1 No. 780

7 Rechargeable Emergency lamp( 600mmfluorescent lamp) 1 No. 3101

H.T. SUPPLY

8 Teak Wood ladder –5M Ht. 1 No. 1588

9 Earth Discharge Rod (3 Nos. -RYB) 1 No. 1328



132

19.0 TWIN CI EARTHING as per IS 3043/1987 and Latest amendments


in Rupees

1 Upto 25 HP installation 1 No. 12644

2 Above 25-60 HP 1 No. 19460

3 Above 60-150 HP 1 No. 30341

4 Above 150 HP 1 No. 48648

Note : 1) The above rates are basic rates only.2) GST extra applicable as per GO3) In case of collector well the collector well distance from the bank of the

river should be ascertained to find out the weight of GI strip to be usedonly in the foot bridge and rate of Rs.47/- per Kg should be adopted forestimation and this amount should be added with the above rates.

133

20.0 TOOLS


in Rupees

1 6” Chain wrench best India make or equivalent 1 No. 6742 8”Chain Wrench Best India Make or equivalent 1 No. 9113 Connector Screw Driver 901 Taparia Make or

equivalent 1 No. 594 200mm Screw Driver 825 Taparia Make or



equivalent 1 No. 2617 200mm Cutting Plier Taparia Make or equivalent 1 No. 3178 800gm Ball Pane Hammer with Handle Taparia Make 1 No. 4009 Digital Tong Tester CE Make or equivalent 1 No. 353710 Digital Multi Meter CE Make or equivalent 1 No. 237611 15” Screw Spanner Taparia Make or equivalent 1 No. 82312 12” Bearing Puller 1 No. 81713 Lever Type Grease Gun 1 No. 66814 12”Screw Spanner 1 No. 60515 Crow Bar 5” 1 No. 59116 1” Cold Chisel 1 No. 21617 Hacksaw Frame with Blade 1 No. 13418 Electrical Air Blower 1 No. 306519 Digital Tachometer 1 No. 205920 Hand Crimpling Tool 8” 1 No. 55721 DE Spanner set 6 to 32 Jhalani Make or

equivalent 1 No. 106622 Rings spanner set 6 to 32 Jhalani Make or

equivalent 1 No. 238623 Pipe Wrench 24” Jhalani Make or equivalent 1 No. 136524 Pipe Wrench 14” Jhalani Make or equivalent 1 No. 67425 12” Flat rough File Scissors Make or equivalent 1 No. 33626 12” Flat smooth File Scissors Make or equivalent 1 No. 50627 12”Round File Rough Scissors Make or equivalent 1 No. 39128 12” Round File Smooth Scissors Make or equivalent 1 No. 46729 12”Half Round File Rough Scissors Make or

equivalent 1 No. 68330 12”Half Round File Smooth Scissors Make or

equivalent 1 No. 683



134

21. H.O.T. CRANE AND ACCESSORIES


in Rupees

1 2T capacity hand operated over head Travelling

(HOT) crane suitable for a span upto 6 Mtrs,

and travel length upto 10 Mtrs. with clear liftupto 6 Mtrs. including gear type chain pulley

block with GI chain and geared Travelling trolley

complete with all accessories including girder 1 No. 346059.00

2 2T HOT crane with above specifications upto

8 M Span including Girder 1 No. 359473.00

3 2T HOT crane with above specifications upto10 M Span including Girder 1 No. 390742.00


(HOT) crane suitable for a span upto 6 Mtrs,and travel length upto 10 Mtrs. with clear lift

upto 6 M including gear type chain pulley block

and geared Travelling trolley complete withall accessories including Girder. 1 No. 374544.00


8 M Span including Girder. 1 No. 405369.00

6 3T HOT crane with above specifications upto10 M Span including Girder. 1 No. 420370.00


(HOT) crane suitable for a span upto 6 Mtrs, andtravel length upto 10 M with clear lift upto 6 M

including gear type chain pulley block and

geared Travelling trolley complete with allaccessories including Girder. 1 No. 441075.00


8 M Span including Girder. 1 No. 473923.00


10M Span including Girder. 1 No. 492685.00

Note: 1) The above rates are basic rates inclusive of handling charges.2) GST extra applicable as per GO

135

22.0. Submersible Centrifugal Sewage non clog pumps

Supply and delivery of submersible centrifugal sewage non-clog pumps, vertical spindletype pump , wear resistance with submersible motor for the various duty conditions asstated in the annexure. Pump shall be capable of handling min 100 mm solid size withsewage specific gravity of up to 1.05. Pump shall be of robust construction . Liquidpassages shall be finished smooth and designed as to allow free passage to solids.Pump Impeller should be of Non-clog semi open type , single vane / multi vanepreferably contra bloc or vortex impeller design. Double mechanical seal with siliconcarbide faces should be provided to protect the motor from ingress of sewage alongthe shaft. The critical speed of the rotor shall be at least 30% above the operatingspeed. Pumps to have double bearings between the pump & motor. The bearings lifeshall be minimum 100,000 hrs of operation with greased for life. Pump should beprovided with automatic coupling device including pedestal, duck foot bend, stainlesssteel guide pipe or related accessories of suitable size to facilitate lifting and loweringinto guide rails for easy maintenance. Pump shall be provided with a stainless steellifting chain conforming to BS 970 Gr 304. Pump speed shall be of 9600rpm for highduty pumps and 960/1450 rpm for low duty pumpsets. Casing and impeller should be ofCI Gr. FG 260 :IS210 more preferably with hardened impeller. Shaft should be ofstainless steel AISI 410. All the fasteners and bolts shall be of AISI 410.The submersiblemotor shall be operated with 3 ph , 415 V( + or – 10 % ) , 50 Hz ( + or - 5 % ) dryinduction type. Motor shall be capable of giving rated output without reduction in theexpected life span when operated continuously . The rotating assembly shall bedynamically balanced as per standards. The starting current of the motor shall notexceed 200% of rated full load current for Star / Delta or ATS starting under anycircumstances .The motor shall be suitable for full voltage star delta / ATS starting.The locked rotor current of the motor shall not exceed 600% of full load current unlessotherwise specified. Motor shall be designed to withstand 120 % of rated speed fortwo minutes without any mechanical damage , in either direction of rotation. Themotor vibration shall be within the limit specified in applicable standards . Motorshould be of IE2, explosion proof compatible for VFD operation together with star-Delta / ATS starter, protection against increase in stator winding temperature (15 degCelsius) , bearing temperature, leakage in the stator housing and terminal box shall beprovided and to be suitably interlocked with the control panel for tripping the pump incase of increase in temperature beyond set limit.

Insulation class shall be of “Class H” and degree of protection shall be of IP 68 asper IS 4691. Motor shall be suitable for continuous operation in fully submerged orpartially submerged condition.The pumpset shall be supplied with power cable ofPVC insulated and PVC sheathed , copper , flexible ,round type with requiredconductor size and number of cores as per starting method and of specified lengthfor continuous use under water and air. The control cable of PVC insulated , PVCsheathed , flexible for stator winding temperature sensor 3 core x 1.5 sq.mmcopper conductor and for bimetallic switches 2 core x 1.5 sqmm copper conductorshall be provided. Motor shall be supplied with 10 mts of round submersiblecopper cable of suitable size.

The non clog submersible pumpset shall be provided with suitable starter controlpanel having all protections as mentioned above. (upto 5 HP - DOL Starter, above5 HP to 25 HP -Star Delta Panel and beyond 25 HP shall be ATS)

136


in Rupees

10 m upto 15 m head

1 Discharge Upto 20 M3/hour 1 No 477476

2 Discharge 20 to 100 M3/hour 1 No 477476











above 15m upto 20 m head













above 20 m upto 25 m head




137


in Rupees










above 25 m upto 30 m head













Note : 1) The above rates are basic rates inclusive of transportation handlingcharges.


138

.

139

III ( C ) RATES FORELECTROMECHANICAL ITEMS

140

.

141

III ( C ) RATES FOR ELECTROMECHANICAL ITEMS

Sl. Rates for

No. Description Unit 2020-21in Rupees

1 Selector Switch for Panel Board /Cubical Panel Board/ Starter

a Voltmeter Selector Switch - 6A Each 284b Ammeter Selector Switch - 6A Each 5472 Multi Functions Meters - Flush type for

M V Panel Board

a LED type, CT/PT, Voltage, Current, Frequency,Kilowatt, Kilo Volt Ampere, KVAR , KVAH, RunHours, unbalance(V,A),Rpm, Phase angles,Thd-Class 1 With RS 485 Port Each 17874

b LED type, CT/PT, Voltage, Current, Frequency,Kilowatt, Kilo Volt Ampere, KVAR , KVAH, RunHours, unbalance(V,A), Rpm, Phase angles,Thd - Class 0.5 With RS 485 Port Each 21846

3 Ammeter - Digital

a 96 mm X 96 mm Single Phase AmmeterClass 1-5A Each 2537

b 96 mm X 96 mm Single Phase AmmeterClass 1-1A Each 2758

c 96 mm X 96 mm Three Phase AmmeterClass 1-5A Each 3089

d 96 mm X 96 mm Three Phase AmmeterClass 1-1A Each 3420

4 Pressure Gauge only

a 50 mm upto 60 Kg/CM2 with s.s.case Each 652b 50 mm Glycerine filled upto 400 Kg/CM2 Each 1463c 63 mm upto 60 Kg/CM2 with s.s.case Each 676d 63 mm Glycerine filled upto 400 Kg/CM2 Each 1553e 80 mm upto 60 Kg/CM2 with s.s.case Each 877f 80 mm Glycerine filled upto 400 Kg/CM2 Each 2588g 100 mm upto 60 Kg/CM2 with s.s.case Each 1350h 100 mm Glycerine filled upto 400 Kg/CM2 Each 3150i 150 mm upto 60 Kg/CM2 with s.s.case Each 1632j 150 mm Glycerine filled upto 400 Kg/CM2 Each 3713k 200 mm upto 60 Kg/CM2 with s.s.case Each 3600l 200 mm Glycerine filled upto 400 Kg/CM2 Each 7989m 250 mm upto 60 Kg/CM2 with s.s.case Each 4501n 250 mm Glycerine filled upto 400 Kg/CM2 Each 9002

142

5 Mechanical Interlocking System forM V Panel Board

a 2 lock 1 key Each 3004b 3 lock 2 key Each 52446 Ammeter Analoga SR 65 5D/5A C.T.operated-AC Each 546b SR 72 5D/5A C.T.operated-AC Each 708c SR 96 5D/5A C.T.operated-AC Each 7577 Voltmeter - Digitala Voltmeter- Single Phase Class 1-AC Each 2537b Voltmeter- Three Phase Class 1-AC Each 34208 Voltmeter Analoga Voltmeter SR 65 600V-AC Each 598b Voltmeter SR 72 500V-AC Each 783c Voltmeter SR 96 600V-AC Each 8669 Fabrication & Supply of M V Cubical Panel

board vermi proof box of MS sheet 20 SWGpowder coated, door with 180 degreeopening, poly urethane/rubber gasketsas per IE rules - 1m2

a Projection of 0.3 m per m2 13654.00b Projection of 0.45m per m2 15839.00c Projection of 0.6 m per m2 20645.00

10 Electro magnetic contactors of suitablecapacity in AC Three Phase rating,conforming to IS/IEC 60947-4-1.

a 9Amps No. 792b 12 Amps No. 920c 18 Amps No. 1585d 22 Amps No. 2623e 25 Amps No. 3406f 32 Amps No. 4157g 40 Amps No. 4326h 45 Amps No. 5350i 50 Amps No. 6300j 70 Amps No. 8470k 80 Amps No. 10739l 95 Amps No. 13541m 110 Amps No. 16314n 140 Amps No. 21530

Sl. Rates for


143

o 185 Amps No. 25903p 225 Amps No. 28515q 250 Amps No. 32167r 300 Amps No. 38785s 400 Amps No. 49315t 550 Amps No. 70721u 650 Amps No. 105830

11 Overload Relays: Directly operatedBimetallic Thermal overload relay whichoperates in case of overload and also incase of under voltage with manual andauto reset mode.

a Upto 5 A No. 1255b 5 A to 10 A No. 1265c 10 A to 20 A No. 1423d 20 A to 30 A No. 2060e 30 A to 50 A No. 2836f 50 A to 75 A No. 4111g 75 A to 110 A No. 6077h 110 A to 150 A No. 7242i 150 A to 200 A No. 8231j 200 A to 300 A No. 9914

12 Preventer – Single PhasingElectric Motor protection device against singlephasing. The device should protect the motoragainst single phasing, reverse phasing andunbalance supply. The device should besuitable for any device and have provisionsfor mounting in panel boards. Operate withoutneed of any auxiliary supply. No. 1103.00

13 Preventer – Dry RunElectric Motor protection device against dryrunning. The device should protect the motoragainst Dry running. The device should besuitable for any auxiliary device and haveprovisions for mounting in panel boards.Operate without need of any auxiliary supply No. 1544.00

Sl. Rates for


Note: 1. The above rates are basic rates.2. GST extra applicable as per G.O.

144

.

III (D) RATES FOR BUILDING MATERIALS

146

.

147

BUILDING MATERIALS

1. Cement - Rs. 5,800/ – per metric tonne

(Rupees Five Thousand and Eight Hundred only)

The above rate for cement is basic rate and GST extra applicable as per GO.

Necessary lead charges (i.e. excluding loading and unloading charges), as applicable as

per conveyance table, may be allowed from the Dealer’s Godown / stockyard to the site

of work, if duly certified by an Officer not below the rank of Assistant Executive Engineer.

However, in the case, if the source is specified as “Stockyard” the same shall be

decided and approved by the Superintending Engineers concerned.

2. Steel Rods of all sizes - Rs.45,000/- per metric tonne

(Rupees Forty Five Thousand only)

The above rate for steel is basic rate and GST extra applicable as per G.O.

Necessary lead charges (i.e. excluding loading and unloading charges), as applicable as

per conveyance table, may be allowed from the Dealer’s Godown / stockyard to the site

of work, if duly certified by an Officer not below the rank of Assistant Executive Engineer.

However, in the case, if the source is specified as “Stockyard” the same shall be

decided and approved by the Superintending Engineers concerned.

(The above rates are subject to revision as and when revised by the PWD

authorities)

148

.

149

BUILDING MATERIALS

Rate forSl. No. Description Unit 2020-21

in Rupees

1 Bricks-II Class Table Moulded (Chamber burnt)

a. 9” x 4 ½” x 3” 1000 Nos. 7509.00

b. 9” x 4 3/8” x 2 ¾” 1000 Nos. 7221.00

2 Bricks-II Class (Ground Moulded Chamber burnt)

a. 9”x 4 ½” x3” 1000 Nos. 6469.00

b. 9”x 4 3/8” x 2 ¾” 1000 Nos. 6282.00

3 Bricks-III Class (Country Bricks, Kiln burnt)

a 22 x 11 x 5 cm (8 ¾” x 4 ¼” x 2”) 1000 Nos. 4095.00

b. 22 x 11 x 5.7 cm (8 ¾” x 4 ¼” x 2 ¼”) 1000 Nos. 4277.00

c. 22 x 11 x 7cm (8 ¾ ” x 4 ¼ ” x 2 ¾”) 1000 Nos. 5438.004 Fly Ash bricks

a. 230 x 110 x 70mm 1000 Nos. 6282.00

b. 230 x 110 x 75mm 1000 Nos. 6469.005 Bricks Country (specially moulded for well steining)

a. 8 ¾ ”x 4 ¼ ” x 2” 1000 Nos. 2408.00

b. Perforated Bricks 19 x 9 x 9cm 1000 Nos. 3671.00c. Terrace Bricks 15 x 7.5 x 2.5cm 1000 Nos. 943.00

6 Special Bricks 8" x 4" x 2" for Heritage works 1000 Nos. 12726.00

7 Terrace Bricks 6" x 3" x 1" for Heritage works 1000 Nos. 9544.008 Wire cut Bricks for Heritage works

a Size 9” x 4” x 3” 1000 Nos. 12726.00

b Size 9” x 4” x 2” 1000 Nos. 10605.00c. Size 9” x 6.5” x 2” 1000 Nos. 15907.00

9 Flat Tiles

a. 15cm x 15cm x 12mm 1000 Nos. 789.00b. 15cm x 15cm x 20mm 1000 Nos. 937.00

10 Brick Jelly

a. 40mm size cu.m. 672.00b. 20mm size cu.m. 749.00

11 Pressed Tiles

a. 20cm x 20cm x 2cm 1000 Nos. 11356.00b. 23cm x 23cm x 2cm 1000 Nos. 16106.00

12 Pan Tiles

a. 23cm x 8cm x 1.7cm 1000 Nos. 429.00b. 16.5cm x 8cm x 1.7cm 1000 Nos. 353.00

150

13 Best Mangalore Tiles

a. 1st Class ’A’ 1000 Nos. 10286.00

b. Class ’AA’ 1000 Nos. 10498.00

c. Best Mangalore Ridge Tiles 1000 Nos. 30118.00d. Best Mangalore Ceiling Tiles 1000 Nos. 6330.00

e. Best Mangalore Glass Roofing Tiles Each 296.00

f. Best Mangalore Ventilating Tiles (Single) Each 44.40g. Best Mangalore Ventilating Tiles (Double) Each 56.50

14 Mosaic Flooring tiles GREY


15 Mosaic (other colour)


c. Mosaic (Green)Tile 20cm x 20cm x 2cm 1000 Nos. 11559.00

d. Mosaic (Green) Tile 25cm x 25cm x 2cm 1000 Nos. 18134.00e. Mosaic Chequered Tile of Grey colour size

25 cm x 25 cm x 2 cm 1000 Nos. 14528.00

16 Attangudi Tiles for Heritage Worksa Size 8” x 8” x 3/4" Each 26.20

b Size 10” x 10” x 3/4" Each 31.80

Stone and Road materials

17 Rough stone for Masonry works (Hard Granite) cu.m. 437.00

18 Rough stone for revetment works cu.m. 378.00

19 Jeddy size for revetment (Hard granite) cu.m. 416.0020 Cut stone pillar of size 0.15 x 0.15 x 2.1M Each 161.00

21 From boulders without blasting for revetment cu.m. 111.00

22 From boulders without blasting for masonry cu.m. 144.0023 Course Rubble stone for masonry works cu.m. 349.00

24 Course Rubble stone for Arch works cu.m. 378.00

25 Chisel dressed stone

a. 70cm x 30cm x 29cm Each 172.00

b. 37cm x 30cm x 29cm Each 155.00

26 Hammer dressed stone

a. 37cm x 30cm x 29cm Each 120.0027 Cut stone fully dressed to size on all faces cu.m. 6256.00


in Rupees

151

28 Cut stone roughly dressed cu.m. 4305.0029 Ashlar arch stone fully dressed to size all faces cu.m. 4751.0030 Flooring stone SS size (not less than 10cm thick) sq.m. 347.0031 Stone slab for culvert (3 faces, one line dressed)a. Above 1.2m cu.m. 4532.00b. Up to 1.2m cu.m. 4119.0032 Stone slab for culvert (3 faces, two line dressed) cu.m. 5047.0033 For lintel coping (3 faces, two line dressed) cu.m. 5047.0034 Bond stones cu.m. 630.0035 Kilometre stone 1.65 x 0.45 x 0.15m Each 431.0036 Hecta metre stone

a. 0.90 x 0.10 x 0.10m Each 120.00b. 0.75 x 0.23 x 0.10m Each 220.00c. 0.90 x 0.15 x0.15m Each 216.0037 Demarcation stone (Two line dressed for top 30cm)

a. 0.75 x 0.15 x 0.15m Each 89.80b. 0.90 x 0.23 x 0.23m Each 115.00c. 0.75 x 0.23 x 0.23m Each 107.00d. 0.90 x 0.15 x 0.15m Each 97.90e. Demarcation Stone with letters cut 0.75 x 0.15 x 0.15m Each 120.00f. Edge stone 0.45 x 0.15 x 0.15m Each 54.50g. T.R.S. Bench Mark Stone neatly dressed the exposed

surface to a height of 15cm including cutting lettersi) 0.15 x 0.15 x 0.60m Each 138.00ii) 0.10 x 0.10 x 0.25m Each 99.80

38. a. Guard Stone (Two line dressed for 45cm)23cm dia 1.0m long Each 159.00

b. Guard stone (Top 0.70m chisel dressed and 0.50mbottom roughly dressed) 0.23m x 0.23m x 1.20m long(Two line dressed top 45cm) 23cm dia 1.0m long Each 170.00

c. Guard stone (Top 0.70m chisel dressed and 0.50mbottom roughly dressed) 0.23m x 0.23m x 0.9m long(Two line dressed top 45cm) 23cm dia 0.90m long Each 159.00

d. Guard stone (Top 0.70m chisel dressed and 0.50mbottom roughly dressed) 0.15m x 0.15m x 0.90m long(Two line dressed top 45cm) 23cm dia 0.90m long Each 111.00

e. Guard stone 90cm long 23cm dia Each 81.80


in Rupees

152

39 Hard broken Granite stone jelly (I.S.S.)

machine crushed / Hand broken.

i. 90mm size cu.m. 430.00ii. 80mm size cu.m. 481.00iii. 63mm size cu.m. 556.00iv. 50mm size cu.m. 645.00v. 40mm size cu.m. 1004.00vi. 25mm size cu.m. 863.00vii. 20mm size cu.m. 1398.00viii. 12mm size cu.m. 1297.00ix. 10mm size cu.m. 954.00x. 6mm size cu.m. 645.00xi. 3mm size cu.m. 581.0040 Quartz metal

i. 50mm cu.m. 94.90ii. 40mm cu.m. 95.9041 Soft broken stone

i. 63mm cu.m. 72.70ii. 40mm cu.m. 81.8042 Laterite 40mm to 75mm size cu.m. 94.9043 Kankar 40mm to 75mm size cu.m. 94.90

44.a Soling stones 15cm cube (un blasted) cu.m. 111.00b. Soling stones 15cm cube (blasted) cu.m. 181.00

45.a Gravel cu.m. 210.00b. Well Gravel cu.m. 157.00c. Screened Kankar Gravel cu.m. 115.00

46.a Quarry rubbish cu.m. 93.90b. Stone dust cu.m. 120.10c. Pond Ash (wet /dry) cu.m. 92.90d Crushed Stone Sand (M-Sand) cu.m. 1250.00e. Plastering sand (P- Sand) cu.m. 1255.0047 Sand for Mortar ** cu.m. 447.0048 Sand for Filling ** cu.m. 447.0049 Clay for puddle and masonry cu.m. 36.30

50. i) Cuddapah slab 50mm thick sq.m 413.00ii) Cuddapah slab 38mm/40mm thick sq.m 397.00iii) Cuddapah slab 20mm/30mm thick sq.m 366.00


in Rupees

153

LIME

51 Shell Lime (Slacked and screened) cu.m. 1297.0052 Freshly Slacked and Screened Burnt Lime Stone cu.m. 955.0053 Stone Lime or Lime Metal cu.m. 82.6054 Unslaked Pollachi Lime for Heritage Works cu.m. 10143.0055 Teakwood scantlings (over 3m for joists and rafters)

Malabar cu.m. 116600.0056 Teakwood scantlings

(for tiebeams and principal rafters) - Malabar cu.m. 114700.0057 Teakwood scantlings (over 2m and below

3m in length) - Malabar cu.m. 111600.0058 Teakwood scantlings(below 2m in length ) – Malabar cu.m. 99400.0059 Teakwood planks

i) Over 45cm wide and 12mm thick. cu.m. 123100.00ii) Over 30cm and up to 45cm wide and 12mm thick cu.m. 114300.00iii) Over 30cm and up to 45cm wide and 12mm to 25mm thick cu.m. 107000.00iv) Over 30cm and up to 45cm wide and 25mm to 40mm thick cu.m. 102600.00v) Over 15cm and up to 30cm wide and 12mm thick cu.m. 99900.00vi) Over 15cm and up to 30cm wide and 12mm to 25mm thick cu.m. 95000.00vii) Over 15cm and upto 30cm wide and 25mm to 40mm thick cu.m. 93100.00viii) Up to 15cm wide and 12mm thick cu.m. 91300.00ix) Up to 15cm wide and 12mm to 25mm thick cu.m. 91300.00x) Up to 15cm wide and 25mm to 40mm thick cu.m. 86200.0060 Seasoned Teakwood for Scantling and Planks for

Heritage Works 185200.0061 Teak Wood Reepers

i) 50mm x 25mm RM 76.00ii) 50mm x 12mm RM 61.0062 Country wood Scantlings

i) Up to 4m in length cu.m. 34300.00ii) Over 4m in length cu.m. 36200.0063 Country wood scantlings (for tiebeams and principal

rafters for trusses) cu.m. 36200.0064 Jack wood Scantlings (up to 4m) cu.m. 37900.0065 Silver Oak Scantling cu.m. 15500.0066 Country wood planks

i) 40mm thick- upto 30cm wide cu.m. 39400.00ii) 25mm thick - up to 30cm wide cu.m. 39400.00


in Rupees

154

iii) 40mm thick - over 30cm wide cu.m. 39400.00iv) 25mm thick - over 30cm wide cu.m. 39400.00

67.a. Jack wood planks 25 to 40mm thick cu.m. 41300.00b. Silver Oak plank (40mm thick) cu.m. 17600.00c. Blue gum plank cu.m. 18100.0068 Country wood reepers

a. 50mm x 25mm RM 34.60b. 50mm x 12mm RM 24.9069 Mango Plank cu.m. 16700.00

70.a. Palmyrah rafter (50mm to 60mm wide and 125mm depth) RM 49.50b. Palmyrah leaves 100 Nos. 255.00c. Palmyrah leaves (Labour for cutting) 100 Nos. 40.2071 Casurina Poles

a. 13cm to 15cm diameter RM 33.00b. 10cm to 13cm diameter RM 25.20c. 8cm to 10cm diameter RM 19.20d. 5cm to 8cm diameter RM 17.5072 Eucalyptus Poles

a. 13cm to 15cm dia RM 33.00b. 10cm to 13 cm dia RM 23.60c. 8 cm to 10 cm dia RM 19.20d. 5 cm to 8 cm dia RM 16.40e. Below 5 cm RM 15.0073 Eucalyptus Bullies 4cm to 5 cm dia & cross ties RM 12.0074 Casurina Bullies 4cm to 5cm dia & cross ties RM 13.5075 Bamboo large

i) 10cm diameter and above RM 12.00ii) 7.5cm to 10cm diameter RM 10.60

METAL AND IRON ITEMS

76 Mild steel plates or sheets BG 10 Kg. 41.2077 Mild Steel Angles 25mm x 25mm x 3mm Kg. 41.20

78.a) Binding wire (Black 18G) Kg. 43.75b) Binding wire (Galvanised – 18G) Kg. 43.7579 G.I. sheets 30cm wide and 1.6mm thick sq.m. 304.0080 Weld mesh

i) 7.5 x 2.5cm, 10 gauge sq.m. 295.00ii) 7.5cm x 5cm, 10 gauge sq.m. 264.00


in Rupees

155

iii) 10cm x 10cm, 10 gauge sq.m. 143.0081 Chicken Mesh sq.m. 31.6582 Fly Proof Mesh sq.m. 91.0083 Supplying mild steel grills for windows, ventilators, etc.,

including priming coat Kg. 54.50Note:

1. For Road works, the Schedule of Rates of Highways Department may be adoptedin respect of materials for which rates are not available in this schedule of rates.

2. For all the materials viz. Bricks and Tile products, Stone Jelly, Gravel, Sand, LimeStone etc., necessary incidental charges , loading charges and unloading chargeshave been included in the basic cost of materials listed above. Hence no separateincidental charges, loading and unloading charges shall be allowed for the abovematerials.

3. The above rate is exclusive of all tax and GST.4. ** The cost of sand as indicated Sl. No. 47 & 48 is at Government sand Depot.


in Rupees

156

.

157

III (E) RATES FOR OTHERCONSTRUCTION MATERIALS

158

.

159

RATES OF OTHER CONSTRUCTION MATERIALSNote : No extra on cost, conveyance charges shall be allowed for all the items

included under this category. The rates approved therein are applicableat site of work.


in Rupees

1 Water proofing compound Kg 41.90

2 Mild Steel Flats of all sizes Kg 40.45

3 Mild Steel Square Rods of all sizes Kg 40.45

4 First Quality Design Ceramic tiles of all coloursi 305 mm x 305 mm x 6 mm Each 45.00

ii 200 mm x 200 mm x 6 mm Each 19.80

iii 200 mm x 100 mm x 6 mm Each 10.705 First Quality Plain ceramic tiles of all colours

i 305 mm x 305 mm x 6 mm Each 32.20

ii 200 mm x 200 mm x 6 mm Each 14.40iii 200 mm x 100 mm x 6 mm Each 7.40

6 Joint free Rectified Glazed Ceramic Flooring

Tiles 305 x 305 x 8 mm Each 53.007 Solar Reflective Ceramic Tiles of Size

i. 305mm x 305mm x 7mm thick sq.m. 464.00i. 305mm x 240mm x 6mm thick sq.m. 383.00

8 Dadooing Ceramic Tiles of Size

300mm x 450mm x 8mm Each 57.209 Dadooing Ceramic Tiles of Size

300mm x 600mm x 10mm Each 85.00

10 First quality White glazed tilesi 150 mm x 150 mm x 6 mm Each 7.70

ii 100 mm x 200 mm x 6 mm Each 6.70

11 First quality colour glazed tilesi 150 mm x 150 mm x 6 mm Each 8.90


12 First quality colour glazed tiles with printed designi 150 mm x 150 mm x 6 mm Each 10.50


13 Colour designed glazed tiles 300 x 200 x 6 mm Each 28.3014 Stain free Nano polish Vitrified Tiles 600x600x 8mm sq.m. 603.00

15 Double charged Vitrified Tiles 800 x 800 x 10mm sq.m. 1150.0016 Pre-polished concrete anti-skid step tiles of 20mm thick sq.m. 599.00

160

17 Rubber Moulded Hydraulic Pressed Paver Block

i. 83mm thick sq.m. 542.00

ii. 63mm thick sq.m. 451.00

18 TAMIN Paver Block of size - Supply at site

i. 60mm thick sft 50.60

ii. 80mm thick sft 60.60

19 Tactile paver Type of New Tek BT Yellow colour

ceramic tiles of size 305x305x15mm for vision

Impairment person sq.m. 2000.00

20 Providing and filling the tile join with epxy grout with

folllowing specificaion:Surface preparation including

cleaning the joint to be free from dust and loose

particles. Providing masking sealing tape on either side

of the tile joint edges and and providing sealing the tile

gap with epoxy tile joint grout and finishing neatly and

as directed by the departmental officers. The rate

inclusive of cost of materials and labour, etc., complete. sq.m. 430.00

New Item

21 SRC Cement (Sulphate Resisitant Cement) 50 kgs/

bag 300.00

22 Slag Cement 50 kgs/

bag 270.00

23 White Cement Kg 22.20

24 Colour Cement (White cement mixed with

colouring pigments) Kg 26.80

25 Multi-colour marble chips of all Grades / Sizes Bag 89.40

26 White Marble slab (Adanga) 18 mm to 20 mm thick

i 4’0'’ x 2’0'’ and above sq.m. 1378.00

ii 2’0'’ x 2’0" or 2’0" x 1’0" or 1’0" x1’0" sq.m. 688.00

27 Granite tiles - (Superfine polished with

Machine cut edges) of size 2’0" x 1’0" or 1’0" x 1’0" or

1’0" x 0’6", of 10 mm thick

a Jet Black sq.m. 844.00

b Ruby Red, Raw Silk sq.m. 756.00

c Sinthetic Grey, Paradise and Similar varieties. sq.m. 714.00


in Rupees

161

28 Granite slabs (Super fine polished with machine cutedges) of sizes 4’x2' and above 18mm to 20mm thick.

a Jet Black sq.m. 1706.00b Ruby Red, Raw Silk sq.m. 1595.00c Sinthetic Grey, Paradise and Similar varieties. sq.m. 1434.00d Fine polished Steel Grey Granite Slab

1200mm x 600mm, 16mm to 18mm thick sq.m. 1484.00e Fine polished Blue Pearl Granite Slab

1200mm x 600mm, 16mm to 18mm thick sq.m. 7423.0029 Flamed Steel Grey Granite Slab

1200mm x 600mm, 16mm to 18mm thick sq.m. 1797.0030 Flamed Ruby Red Granite Slab

1200mm x 600mm, 16mm to 18mm thick sq.m. 1908.0031 Nosing for Granite slaba Single Nosing RM 191.90b Double Nosing RM 363.0032 Polished shahabad stone slabs of 20 mm thick with

machine cut edges of size 2' 0" x 2’0" and above. sq.m. 370.0033 Polished shahabad stone slabs 20 mm thick with

machine cut edges of size below 2' 0" x 2’0". sq.m. 312.0034 Polished Rajasthan Kota stone slabs of 20 mm thick

with machine cut edges of size 2' 0" x 2’0" and above. sq.m. 540.0035 Polished Rajasthan Kota stone slabs of 20 mm thick

with machine cut edges of size below 2’0" x 2’0". sq.m. 476.0036 Dolphur stone slabs - semi polished with machine

cut edges of all sizes

a 40 mm thick sq.m. 412.00b 20 mm thick sq.m. 375.00

37 PVC Trims (Beading) RM 90.00

38 Teracota Jally of size 20x20x0.75mm Each 38.3039 Aluminium strips of size 40 mm wide x 1.5 mm thick RM 32.3040 Brass strips of size 40 mm wide x 1.5 mm thick RM 67.9041 Glass strips of size 40 mm wide and 4 mm thick RM 15.4042 Marblex Tiles 3 mm thick sq.m. 664.0043 Red Oxide - Superior quality for floor finish Kg 142.4044 Decorative pressed tiles of 12 mm thick of

all sizes and shapes sq.m. 1055.00


in Rupees

162

45 Exterior Emulsion Paint - Water based primer (Liquid) Litre 148.40

46 Alkali Resistant Distemper Primer Litre 133.00

47 Sandtex matt Litre 155.00

48 Vinaratex or equivalent Textured coat sq.m. 199.90

49 Best Lac Polish / French Polish Litre 259.00

50 Varnish Litre 266.00

51 Cotton Waste Kg 10.20

52 Cement based Hydraulically pressed Anti skid tiles

(pattern design) - 20 mm thick sq.m. 500.00

53 Marble Powder Kg 4.49

54 Polishing Stone

i Rough Each 65.80

ii Medium Each 87.90

iii Fine / Nice Each 100.70

55 Oxalic Acid Kg 38.10

56 Turpentine Litre 23.30

57 Mansion polish 400 gram 146.30

58 Poly Sulphide Kg 173.60

59 Primer for expansion joints Kg 149.30

60 Filler material sq.m. 142.40

61 Bond Breaker RM 3.68

62 PVC Water Bar 150mm wide with single bulb RM 282.80

63 Plain G.I. sheet 0.8mm thick (22 Gauge) sq.m. 357.50

64 Phil Plug Each 4.95

65 G.I. Screws

i 30mm x 6mm Each 1.26

ii 19mm x 6mm Each 0.80

66 G.I. Limpet / Cup Washers Each 1.86

67 Bitumen washers 15mm dia Each 1.11

68 Asbestos Cement pipe - 100mm dia 3 RM 141.30

69 A.C. shoe - 100mm dia Each 44.80

70 A.C. Bend - 100mm dia Each 51.30

71 A.C. Cylindrical Cowl - 100mm dia Each 77.00

72 C.I. Brackets for A.C. pipe 100mm dia Each 19.70

73 C.I. Grating - 100mm dia Each 31.50


in Rupees

163

74 Asbestos cement fully corrugated sheet - 6mm thick sq.m. 186.00

75 Asbestos cement plain sheet

i 6mm thick sq.m. 166.90

ii 4mm thick sq.m. 115.60

New Item

76 Supplying and fixing shade net (Green net) for

under construction of high rise buildings sq.m. 66.00

77 Asbestos cement adjustable ridges Pair 192.60

78 G.I. “J” or “L” Bolts with nuts 6mm Dia Each 3.84

79 Steel - special extruded sections for steel windows

and ventilators conforming to I.S.S. 7452 / 1990

including Fabrication charges Kg 61.50

80 CRCA pressed steel Box section 18 Gauge or 1.25mm

thick for Door frames including providing holes and

fixing wooden blocks for fixing furniture and fittings

a With one coat of Red oxide priming coat. RM 353.00

b With powder coated primer RM 376.70

81 Aluminium extruded sections (for Doors, windows,

ventilartors, partitions, false ceiling etc.) including

charges for Anodising for 15 micron thickness

a Natural colour matt finish. Kg 287.00

b With powder coating of any colours. Kg 307.00

82 Alumninum Extruded Box Section for Staircase

Hand Rails including charges for Anodising for

15 micron thickness - Natural colour matt finish Kg 359.00

83 Rubber beading for aluminium glazed doors RM 37.60

84 Rubber beading for aluminium glazed windows. RM 28.60

85 PVC / Woollen felt for aluminium doors 6mm thick RM 7.55

86 Pivot for Aluminium Door Set 147.40

87 Hydraulic Door closer of various sizes of approved quality

using Aluminium Extruded section body tubular type

universal hydraulic door closer with double speed

adjustment like HARDWYN (make) ‘GAZEL’ (or) equivalent

(with ISI Monogram) Each 890.00


in Rupees

164

88 Hydraulic Floor springs of various sizes double acton

hydraulic floor spring of approved quality, brand,

manufacture as per BIS standards for doors including

cost of cutting floors as required, embedding in to floors

and Stainless Steel Cover plates with Aluminium Pivet

and single piece M.S. sheet outer box with side plate

etc., capable of taking upto 130 Kg. weight from door

shutter, like HARDWYN make (U-32) or its equivalent

with ISI monogram. Each 2055.00

89 Lock for Aluminium doors Each 251.0090 Lock for Aluminium sliding windows Each 62.8091 Aluminium Grill of standard pattern (diamond shape) -

10mm thick including ‘F’ (or) ‘H’ Section. sq.m. 1835.0092 Aluminium Grill of standard pattern (diamond shape) -

6mm thick including ‘F’ (or) ‘H’ Section. sq.m. 1485.0093 Bolts and Nuts 10mm dia for false ceiling Each 5.5594 Rawl Plugs for false ceiling Each 9.4095 PVC Roller for sliding windows Each 13.8596 Synthetic Resin - Fevicol or equivalent

(Phenol Formaldehide based Resin) Kg 195.9097 Butt Hinges with nylon washers of various sizes.

Length and width (with required screws).a 125mm x 30mm Each 79.10b 100mm x 30mm Each 63.50c 75mm x 30mm Each 43.60d 50mm x 30mm Each 35.15

New Item

98 Brass Hinges

125mm x 30mm Each 210.00

100mm x 30mm Each 180.00

75mm x 30mm Each 150.00

50mm x 30mm Each 125.00

99 Tower Bolts of various lengths and diameter(with required screws)

a 400mm long and 12mm dia Each 149.70b 300mm long and 12mm dia Each 115.20c 250mm long and 12mm dia Each 86.30


in Rupees

165

d 200mm long and 12mm dia Each 72.60e 150mm long and 12mm dia Each 57.20f 100mm long and 10mm dia Each 50.30g 75mm long and 10mm dia Each 35.10

New Item

100 Brass Tower Bolts

a 400mm x 12mm Each 1000.00

b 300mm x 12mm Each 750.00

c 200mm x 12mm Each 530.00

d 150mm x 12mm Each 400.00

e 100mm x 10mm Each 320.00

f 75mm x 10mm Each 200.00

101 Aldrops of following lengths and diameter withrequired screws, bolts and nuts.

a 300mm long and 16mm dia Each 185.20b 250mm long and 16mm dia Each 159.70c 200mm long and 16mm dia Each 108.10d 200mm long and 12mm dia Each 89.70

New Item

102 Brass Aldrops

a 300mm x 16mm Each 950.00

b 250mm x 16mm Each 820.00

c 200mm x 16mm Each 700.00

d 200mm x 12mm Each 500.00

103 Handles “D” type of various sizes with required screwsa 200mm long Each 56.70b 150mm long Each 50.90c 100mm long Each 31.20

104 Ornamental handles of various sizes with required screwsa 200mm long Each 146.30b 150mm long Each 97.50c 100mm long Each 53.80

New Item

105 Brass Ornamental Handles

a 200mm Each 390.00b 150mm Each 250.00c 100mm Each 180.00


in Rupees

166

106 Aluminium door stopper with rubber bush withrequired screws Each 43.80

107 Rubber bush - 40 mm dia and 60 mm long withrequired screws Each 22.70

108 Mortice Lock-(Godrej or equivalent) with requiredscrews with 3 Keys

a With night latch Each 530.00b Without night latch Each 394.00c Wire nails Kg 62.80

109 Teakwood beadinga 15mm x 12mm RM 15.15b 35mm x 12mm RM 38.40

110 Teakwood Beading (ordinary)a 30mm x 12mm RM 31.90b 25mm x 12mm RM 25.60

111 Teakwood beading - Ornamental / designa 40mm x 12mm RM 89.70b 40mm x 15mm RM 102.80c 25mm x 12mm RM 70.30d 15mm x 12mm RM 48.30

112 Medium Density Fibre (MDF) Board - Exterior Grade,Both sides pre-laminated including external lippingwith kiln dried soft wood 35mm thick sq.m. 2141.00

113 Medium Density Fibre (MDF) Board - exterior Grade -Both sides pre-laminated, 12mm thick sq.m. 1030.00

114 MDF Board exterior Grade - Plain including externallipping with kiln dried soft wood

i 35mm thick sq.m. 1747.00ii 30mm thick sq.m. 1610.00

115 Medium density fibre (MDF) Board 12 mm thickExterior grade - with melamine finish.

a One side melamine finish sq.m. 1090.00b Both sides melamine finish sq.m. 1227.00

116 Medium density fibre (MDF) board - Exterior grade -Plain - With teak wood external lipping alround

a 35mm thick sq.m. 1878.00b 30mm thick sq.m. 1666.00


in Rupees

167

117 Solid core Flush shutters with Teak ply on both sidewith teak wook lipping alround 35 mm thick sq.m. 2211.00

118 Solid core Flush shutters with Teak ply on one side

and commercial ply on other side with teak woodlipping alround 35 mm thick sq.m. 1944.00

119 Solid core Flush shutters with commercial ply on

both side with teak wood lipping alround 35 mm thick sq.m. 1666.00120 Providing cup board Shutter using termite/ water proof

plywood of 19mm thick over which laminated sheet of0.8mm thick fixed inside the shutter and 1mm thickfixed outside the shutter using fevicol along withnecessary furniture fittings such as hydraulic hingestower bolt handles multi purpose locks etc as directedby the Departmental officers. the design pattern waterproof plywood laminate sheet and other materialsshould be got approved from the Executive Engineerbefore use on work sq.m. 4949.00

121 Solid PVC door shutters using 19 Gauge 19mm MS squaretubes for styles and outer frames. 15mm MS squaretubes for top, lock and bottom rails. The steel tubesshall be covered with 5mm thick solid PVC sheets.Shutter using 5mm thick solid PVC sheets for panellingshall rigidly fixed in position including necessary furnitureand fittings. The over all size of styles shall be 50mmx 30mm. The over all size of top rail, Lock rail andbottom rail shall be 75mm x 30mm. The over all size offrames shall be 50mm x 45mm, with suitable rabate forhousing the shutter.

a Solid panel PVC door with frame sq.m. 2828.00

b Solid panel PVC door without frame sq.m. 2383.00

122 Supplying and fixing of PVC sliding door with roller sq.m. 3030.00123a FRP door Shutter with FRP door frames made out of

FRP Sheets of 3mm thick of over all size 65mm x 50mmwith rebate suitably reinforced using MS Angle / Flats,cost of holdfasts and solid core FRP shutter Panel of5mm thick and hollow core frames of 3mm wall thicknessfor styles and rails etc., of sizes specified by Engineers. sq.m. 3918.00

b Excluding door frames sq.m. 3009.00


in Rupees

168

124a PVC panelled door shutters hollow type -200 mm x 20 mm panels with 1 mm wall thickness forpanels and styles and rails of suitable size with 2 mmwall thickness suitably reinforced using MS Angle /Flat including cost of necessary Aluminium hinges andother furniture fittings. sq.m. 2014.00

b Excluding door frames sq.m. 1701.00125 RCC door frame of 100mm x 65mm cross sectional size

with necessary rebate for housing the shutters,manufactured with cement concrete of grade not lessthan M20 using 10 mm and below graded stone jellyand using steel reinforcement as per C.E. (B) circularinstructions. RM 275.00

126 Stainless Steel (Salem Stainless Steel) Door Frame (BoxSection using Stainless Steel Plate of 1 mm thick) ofsize 100 mm x 60 mm with a rebate of 30/ 35 mm x 15mm on one side of the frame including supplying andfixing dovetail splayed end stainless steel Hold fast etc., RM 900.00

127 Stainless Steel (Salem Stainless Steel) Door Frame(Box Section using Stainless Steel Plate of 1.6mm thick)of size100mmx60mm with a rebate of 30/ 35mm x15mm on one side of the frame including supplying andfixing dovetail splayed end stainless steel hold fast etc., RM 1217.00

128 Supplying and erecting pull and push type rolling shutterwith ISI make of approved size and section using 18 GIsheet. The shutter shall be painted with one coat ofred oxide primer and the rate is inclusive of hood covers,transportation charges etc.,

A ROLLING SHUTTERS (WITH ISI MONOGRAM)a Manually operated (up to 8 m2 area) sq.m. 2131.00b Gear operated type (from 8 m2 to 12 m2 area) sq.m. 2373.00c Electrically operated type (exceeding 12m2 area) sq.m. 2575.00B ROLLING GRILLS (WITH ISI MONOGRAM)a Manually operated (up to 8 m2 area) sq.m. 2171.00b Gear operated (from 8 m2 to 12 m2 area) sq.m. 2444.00c Electrically operated (exceeding 12 m2 area) sq.m. 2716.00

129 Barbed Wire - 10 Gauge - Two ply and four pronged 1 Kg(Galvanised) or 6 RM 60.90


in Rupees

169

130 Chain link - 2" x 2" using 10 Gauge

Galvanised Iron Wire (of all sizes) sq.m. 157.20131 Pin Headed / Fluted / Figured Glass 3mm thick sq.m. 222.20

132 Plain Glass - 4mm thick sq.m. 300.90

133 Plain Sheet Glass - 5.5mm thick sq.m. 355.50134 Metal screws (for Aluminium Doors, windows etc.)

i 75mm x 8mm Each 2.17

ii 38mm x 6mm Each 1.52iii 19mm x 8mm Each 1.06

iv 19mm x 6mm Each 0.80

135 Cement paint (First quality) Kg 48.95136 Oil Bound Distemper Kg 72.40

137 Acrylic Distemper Kg 83.60

138 Primer for Plastic Emulsion paint Litre 144.70139 Plastic Emulsion paint (First quality) Litre 289.80

140 Wood Primer Litre 144.70

141 Synthetic Enamel paint for Wood work Litre 234.30142 Red Oxide primer for Iron work Litre 134.30

143 Synthetic Enamel paint for Iron work Litre 223.20

144 Melamine polish sq.m. 636.00145 Exterior Emulsion Paint Litre 297.90

146 Painting the wall with texture finish paint

including labour charges sq.m. 404.00147 White wall putty powder Kg 27.00

147a Sand paper (Water proof abrasive sheet) Each 10.00

147b 8" Putty blade Dozen 120.00147c 6" Putty blade Dozen 90.00

148 Brass chromium plated screw down Tap 15 / 12mm Dia

(Heavy Type) Each 202.00149 Chromium plated stop cock 15mm Dia Each 148.40

150 Brass chromium plated pillar Tap (Heavy type)-

15/12mm Dia Each 265.00151 Brass chromium plated shower Rose - 100mm Dia Each 190.80

152 CP wall mixture tap 3 in 1 system with hand showers Each 4065.00

153 CP two way bib cock with health faucet Each 2020.00154 CP Shower Arm with Overhead shower rose Each 1160.00


in Rupees

170

155 Wooden plug, clamp and screws Set 12.00156 Shellac 100 gram 18.15157 Thread Ball Each 3.53

New items

158 UPVC Adhesive 100 gram 80.00

159 CPVC Adhesive 100 gram 110.00

160 Vajjram Kg 77.00

161 CP Heavy duty Bottle trap 32mm Each 1085.00162 CP Angle cock tap Each 762.00163 Oriya Type Indian Water closet 580mm x 440mm with

“P” or “S” Trapi White Set 1180.00ii Colour Set 1504.00

164 European Water closet with “P” or “S” Trap withDouble Flapped seat and seat cover with Brass Hingesand 10 litre capacity PVC low level flusing tank withall internal fittings

i White Set 3030.00ii Colour Set 3420.00

165 European water closet with “P” or “S” Trap with Doublefalpped seat and seat cover with Brass Hinges and12.5 litre capacity Porcelin low level flusing tank withall internal fittings

i White Set 4270.00ii Colour Set 5140.00

166 SS Elbow Action tap of size 15mm Each 1515.00167 SS Heavy Duty long body tap 15mm Each 1515.00168 SS Swan Neck Tap Each 1010.00169 PVC water tank Litre 8.60170 Wash Hand Basin of size 550mm x 400mm with all

accessories such as cast iron brackets, 32mm dia C.P.waste coupling, rubber plug and chain, 32mm dia ‘B’Class G.I. waste pipe, 15mm dia G.M. wheel valve, 15mmdia nylon connection, 15mm dia brass nipples, 15mmC.P. pillar tap etc.

i White without pedastal Set 1640.00ii White with pedastal Set 1974.00


in Rupees

171

iii Colour without pedastal Set 2196.00

iv Colour with pedastal Set 2429.00

171 White Porcelin Sink of size 600mm x 450mm x 200mm

with 32mm dia ‘B’ Class G.I. waste water pipe and32mm dia C.P. waste coupling. Set 2105.00

172 Cuddapah Slab Sink of size 600mm x 450mm x 200mm

with 32mm dia ‘B’ Class G.I. waste water pipe & 32mmdia C.P. waste coupling. Set 755.00

173 Cuddapah Slab Sink of size 600mm x 600mm x 200mm

with 32mm dia ‘B’ Class G.I. waste water pipe & 32mmdia C.P. waste coupling. Set 1000.00

New Item

174 Stainless Steel Sink

i 600mm x 600mm x 200mm Each 9000.00

ii 600mm x 450mm x 200mm Each 7000.00

175 Lipped Mouth Porcelin Flat Back Urinal with allaccessories such as 32mm dia Bell mouth PVC

connection, 15mm dia G.M. wheel valve, 15mm dia ‘B’

Class G.I. waste water pipe, 15mm dia nylon connection,15 mm dia brass nipple etc.,

i White Set 922.00

ii Colour Set 1055.00176 Supplying and fixing of SS Sink of size 1200x550x180mm Each 18180.00

177 Supplying and fixing of Granite Sink of

size 600x600x250mm Each 4066.00178 Supplying and fixing Ornamental type White glazed

Porcelain corner L type Wash hand Basin of size 350mm Each 3484.00

179 Supplying and fixing of Oval shape wash hand basinof size 560x450mm Each 2843.00

180 Supplying and fixing of white glazed porcelain ova

shape special type Urianal of size 382x398x601mm Each 9872.00181 Porcelin soap dish of size 150mm x 150mm x 50mm

i White Each 192.40

ii Colour Each 263.60

182 Brass chromium plated soap tray of size

150mm x 100mm Each 161.90


in Rupees

172

183 Brass chromium plated towel rail 60cm long and20mm dia with Brackets Set 263.80

184 SS Towel rack 600mm long with lower hanger Each 1515.00185 Anodised Aluminium Towel Rail 60cm long and 20mm

dia with Brackets. Set 128.00186 PVC / Fibre Glass framed 5.5mm thick mirror, shelf type

with Hard Board Backingi 600mm x 450mm Each 466.60ii 500mm x 400mm Each 375.70

187 Special type Mirror of size 1000x780mm Each 2525.00188 Stone ware gully trap of size 150mm x 100mm with

cast Iron Double Gratings Each 167.10189 Cast Iron Nahini/Floor Trap with stainless Steel Grating

i 100mm x 75mm Each 274.20ii 75mm x 50mm Each 214.80

190 PVC Nahini / Floor Trap with PVC Gratingi 100mm x 75mm Each 151.50ii 75mm x 50mm Each 132.70

191 Spun Yarn Kg 12.90192 Hemp Yarn Kg 11.60193 Gunny Tape / Kithan sq.m. 11.60194 Tar Kg 40.30195 Bitumen Felt 15 mm thick pad sq.m. 230.00196 Supplying, fabricating, erecting and fixing hilux or

equivalent board false ceiling upto a ceiling height of4.5m from floor level.

a Using hilux board plain sheets (10mm thick) sq.m. 954.00b Using perforated sheets (10mm thick) sq.m. 976.00

197 Supplying and laying Glass wool for insulation includingnecessary packing materials.

a Using 50mm thick Glass wool sq.m. 385.00b Using 25mm thick Glass wool sq.m. 205.00

New Item

198 Supply and installation of Anutone (or) Euivalent

Brand of Acoustical False Ceiling of subtex nubby,

square edge, glass fibrecore fully encapsulated

ceiling tile of size 595 x 595 x 15mmhaving volume


in Rupees

173

density 120 Kgs / m3, weight 1.8 / 2.4 / 3 kg /m2which is suspended by using 0.3mm thick skelettrelis T15 metal grid system. Skelet trelis T15 metalgrid system of 600 x600mm module includes skeletWA15 W30 wall angle with unequal flanges of 15 /19mm, length 3000mm, fixed along the perimeterof walls with the help of nylon sleeves andsuitablefasteners at 300mm centers. Then suspendthe skelet MT15W36 MainT with flange width 15mm,height 32mm and length3600mm, from the soffitslab with help of soffit cleat and wire rod withleveling spring clip at 1200mm centres. SkeletCT15W12 CrossT with flange width 15mm, height26mm and length1200mm is interlocked into thepre-cut slots in the Main T15 at 600mm centers inthe perpendicular direction to the Main T15.Finally,the skelet CT15W06 CrossT with flange width15mm,height 26mm and length 600mm areinterlocked into the precut slots in the CT15W12CrossT in direction parallel to the Main T15 to resultin 600 x 600mm module. The subtex nubby squareedge of size 595 x 595 x 15mm shall be placed intothe grid size of 600x 600mm. Ensure arrow marksbehind the tiles are oriented in one direction toachieve uniform shade. The systems to achievenoise reduction coefficient not less than 0.9 NRC,so as to have an neat appearance as directed bythe department offices. The cost includes, cost ofmaterial, cost of labour, scaffolding,transportation, conveyance, etc. complying tostandard specication. sq.m. 1700.00

199 Supply and installation of Anutone (or) EquivalentBrand of Acoustical False Ceiling of Sisoli Serene /Slate Spirts / SlatePolka Mineral Fibre/ GRG CoreCeiling Tiles of size 595 x 595 x15mm havingvolume density 270 kgs / m3, weight 4kg / m2which is suspended by using 0.3mm thick skelettrelis T15 metalgrid system. The skelet trelis T15metal grid system of 600 x600mm module includesskelet WA15 W30 wall angle with unequal flanges


in Rupees

174

of 15 / 19mm, length 3000mm, fixed along theperimeter of walls with the help of nylon sleevesand suitable fasteners at 300mm centers. Thensuspend the skelet MT15 W36MainT with flangewidth 15mm, height 32mm and length 3600mm,from the soffit slab with help of soffit cleat andwirerod with leveling spring clip at 1200mmcentres. Skelet CT15W12 CrossT with flange width15mm, height 26mm and length 1200mm isinterlocked into the pre-cut slots in the Main T15at600mm centers in the perpendicular direction tothe Main T15.Finally skelet CT15 W06 CrossT withflange width 15mm, height 26mm and length600mm are interlocked into the precut slots in theCT15 W12 CrossT in direction parallel to the MainT15 toresult in 600 x 600mm module. Sisoli Serene/ Slate Spirts /Slate Polka of size 595 x 595 x15mm shall be placed into the grid size of 600 x600mm. The systems to achieve noiser eductioncoefficient not less than 0.5 NRC, so as to have anneatappearance as directed by the departmentoffices. The cost includes, cost of material, cost oflabour, Scaffolding,transportation, conveyance,etc., complying to standardspecication. sq.m. 950.00

200 Supply of laying of Anutone (or) Equivalent BrandofAcoustical Insulation of Sound Synth Polywool,50mm thick made from recycled poly fibre and fullyrecyclable, surface density 1000 g / m2, weight1.0 kg/ m2 in form of rolls of 600mm wide and 15minlength, adhered to surface with stick S7 adhesiveorheld in position with chicken wire meshetc., complying to standard specication. sq.m. 420.00

201 Providing Polymer coating (water proof coating) forsunken portion of toilet with following specification andthe surface shall be cleaned to remove all dust, foregin,matters lose material or any other deposits ofcontamination by rubbing with wire brush.Slurry: Dryblend and polymer liquid blend shall be mixed into thedesired ratio as per recommendation of the supplier.the mix shall be stirred thouroughly until no bubbles


in Rupees

175

remain in the mix . Any lumps found in mix shall beremoved. Apply first coat of polymer modifiedcementitious slurry by brush on wet cleaned surface.After drying, second coat shall be applied on the firstcoat as directed by the departmental officers etc., The rateinclusive of cost of materials and labour etc., complete sq.m 323.00

202 Providing Cornice work for Gyp Board false ceiling RM 186.80

203 8mm thick Calcium Silicate Board designed and

perforated for false ceiling sq.m 1515.00

204 Termite proof/ water proof plywood 19mm thick sq.m 1313.00

205 Laminated sheet 0.8mm thick (inside) sq.m 242.00

206 Laminated sheet 1mm thick (outside) sq.m 404.00

207 Double Charged Vitrified Tiles of size 600 x 600 x 8 mm sq.m. 900.00

208 Pre-polished concrete anti-skid step tiles of 20mm thick sq.m. 599.00

209 Colour designed glazed tiles 300 x 200 x 6 mm Each 28.30

210 Squatting Urinal Set 446.00

211 CI Brackets for fixing the sink set 105.90

212 Swan Neck Tap Each 248.00

213 Brass Screws (30 x 6 mm) Each 2.37

214 Brass Screws (75 x 10 mm) Each 4.80

215 Special clamp, teak wood plugs and screws Set 21.20

216 PVC Clamp, teak wood plugs and screws Set 8.35

217 Teak Wood plug Each 1.06

218 Teak wood plug (50 x 50 x 100 mm) Each 5.30

219 Manhole cover 60 x 60 cm (heavy duty) with frame Each 1828.00

220 Welding Charges

a 50 mm Each 2.07

b 40 mm Each 1.61

221 Add for painting/ tarring for Hex Nipple Each 2.77

222 Labour charges for fixing cuddapah slab to cup board sq.m. 45.10

223 Hire charges for polishing machinery Day 224.20

224 Electricity charges Unit 11.70

225 PVC Mould CI steps for sump Each 226.00


in Rupees

176

.

III (G) RATES FOR ELECTRICAL ITEMS

178

.

179

ELECTRICAL ITEMS OF WORKSELECTRICAL LAMPS, FITTINGS AND CONNECTED ACCESSORIES

Note:- No extra on cost, conveyance charges shall be allowed for all the items includedunder this category. The rates approved therein are applicable at site of work.

Rates forItem Description Unit 2020-21No. in Rupees

I PART-A

1 INCANDESCENT BULBS 230V/ 250V GRADE BC/

ES WITH ISI

a. 15 Watts Each 9.35b. 25 Watts Each 9.35c. 40 Watts Each 9.35d. 60 Watts Each 9.35e. 100 Watts Each 9.35f. 200 Watts Each 18.802 INCANDESCENT BULB 230V/250V GRADE BC/ ES

a. Colour 15 Watts Each 11.50b. Blended lamp 160 Watts Each 228.103 PL LAMP (PHILIPS/ OSRAM/EQUIVALENT)

a. 9 Watts Each 71.00b. 11 Watts Each 75.60c. 18 Watts Each 119.20d. 36 Watts Each 132.604 FLUORESCENT TUBULAR LAMPS WITH ISI MARK

a. Cool Day light 2 Ft. 20 Watts Each 35.60b. Cool Day light 4 Ft. 40 Watts Each 35.60c. Cool Day light 4 Ft. 36 Watts Each 34.805 4' 18W crystal Glass LED Tube Light fitting

(Havells / Equivalent) Each 384.306 MERCURY VAPOUR DISCHARGE LAMP 230V

GRADE 3 PIN BC

a. 80 Watts Each 163.80b. 125 Watts Each 172.00c. 250 Watts Each 420.00d. 400 Watts Each 592.007 BOX TYPE SINGLE FLUORESCENT FITTING WITH

COPPER CHOKE AND CONDENSOR COMPLETE

WITH ISI MARK

a. 4 Ft. 40 Watts with ballast Each 303.00b. 4 Ft. 40 Watts Box type with Ballast (Philips/

Crompton / Wipro/ Equivalent) Each 446.00

180

8 BOX TYPE TWIN FLUORESCENT FITTING WITH

COPPER CHOKE AND CONDENSOR[HPF]

COMPLETE WITH ISI MARK

a. 4 Ft. 40 Watts Each 569.00b. 4 Ft. 40 Watts Box type With Ballast (Philips/

Crompton/ Equivalent ) Each 744.009 INDUSTRIAL TYPE FLUORESCENT FITTING STOVE

ENAMELLED WITH COPPER CHOKE AND CONDENSOR

(HPF) 4 Ft. 40W

a. Single type suitable for 1 No. tube Each 839.00b. Twin type suitable for 2 Nos. tube Each 1031.0010 DECORATIVE TWIN FLUORESCENT TYPE FITTING

WITH COPPER CHOKE AND CONDENSOR COMPLETE

SUITABLE FOR 2 NUMBERS FLUORESCENT TUBES

a. 4 Ft. 40W Twin Mirror optic Recessed mounting tubefitting Each 1446.00

b. 4 Ft. 40W Twin Mirror optic Suspension type fitting.(Philips/ Crompton /Wipro/ Equivalent) Each 2607.00

c. 4 Ft. 40W Twin Mirror Optic Recessed mounting typefitting(Philips/ Crompton/ Wipro/ Equivalent) Each 1912.00

11 SINGLE TYPE STREET LIGHT FLUORESCENT FITTING

SUITABLE FOR ONE NO. FLUORESCENT TUBE WITH


a. 4 Ft. 40 Watts type Each 636.0012 TWIN TYPE STREET LIGHTS FLUORESCENT FITTING

SUITABLE FOR 2 Nos. FLUORESCENT TUBES WITH


a. 4 Ft. 40 Watts type Each 856.0013 POST TOP LANTERN FITTING OF (INTEGRAL TYPE)

WITH COPPER CHOKE AND CONDENSOR &

NECESSARY ACCESSORIES (PHILIPS/ CROMPTON

GREAVES/WIPRO/ EQUIVALENT)(SPHERICAL /

RIBBED /CONICAL ACRYLIC COVER)

a. Suitable for 125 Watts M.V lamp Each 3080.00b. Suitable for 70 Watts S.V. Lamp Each 3246.00c. Post top lantern fitting with S.C. holder suitable for

160 W blended lamp/ incandescent lamp Each 1773.00


181

14 CFL STREET LIGHT FITTINGS (COMPACT Higher Lower EndFLOURESCENT LAMP) End Orbit/

Havells / Inventa /Crompton/ Equivalent/Equivalent/

a T5 Street Light (IP65) with EB / 4 x 14W T5 Each 3670.00 2935.00b T5 Street Light (IP65) with EB / 4 x 24W T5 Each 4055.00 3246.00c 1 x 9W CFL Street Light Each 845.00 675.00d 1 x 11W CFL Street Light Each 845.00 675.00e 1 x 13W CFL Street Light Each 850.00 678.00f 1 x 18W CFL Street Light Each 850.00 678.00g 2 x 9W CFL Street Light Each 809.00 647.00h 2 x 11W CFL Street Light Each 989.00 792.00i 2 x 13W CFL Street Light Each 989.00 792.00j 2 x 18W CFL Street Light Each 989.00 792.00k 1 x 36 CFL Street Light Each 1010.00 808.00l 45-1 x 45W 4U Retro CFL B22 Street Light Each 943.00 756.00m CFL - 1 x 85W CFL E27 Street Light Each 1534.00 1228.00n CFL 1 x 85W CFL B22 Street Light Each 1534.00 1228.00o 36WFP-LHF(MS) Street Light Each 1596.00 1275.00p 36WFP-LHF(AL) Street Light Each 1773.00 1414.00q T5 1 x 24W FTL T5 Street Light Each 1654.00 1322.00r T5 2 x 14W FTL T5 Street Light Each 1830.00 1467.00s T5 2 x 24W FTL T5 Street Light Each 1917.00 1534.00t FTL 1 x 36 / 40W FTL Street Light Each 1327.00 1062.00u FTL 2 x 36 / 40W FTL Street Light Each 1892.00 1513.00

New Items15. 4 Feet LED Fitting Higher Lower End

End Orbit/

Havells / Equivalent/

Crompton/ EachEquivalent/

Eacha. 18W 4 Feet LED fitting with LED 747.00 636.00b. 20W 4 Feet LED fitting with LED 758.00 742.0016. LED INDOOR FITTINGS (LIGHT EMITTING Higher Lower End

DIODE) End Orbit/Havells / Equivalent/

Crompton/Equivalent/

a 24W LED 4000K 2 x 2 Square TypeRecessed Fitting with LED Each 3474.00 2463.00

Rates for 2020-21Item Description Unit No. in Rupees

182

b 18W LED 3000K Square Type RecessedFitting with LED Each 1358.00 896.00

c 18W LED 3000K Round Type RecessedFitting with LED Each 1234.00 974.00

17 LED OUTDOOR FITTINGS Higher End Havells /(LIGHT EMITTING DIODE) Crompton/ Equivalent

a 30W LED Street Light Fitting with LED Each 2478.00b 48W LED Street Light Fitting with LED Each 4895.00c 80W LED Focus Light Fitting with LED Each 11660.00d 120W LED Street Light Fitting with LED Each 13785.00e 150W LED Street Light Fitting with LED Each 17180.0018 LED OUTDOOR FITTINGS Lower

(LIGHT EMITTING DIODE) End Orbit /Equivalent

a 25W LED Street Light Fitting with LED Each 1171.00b 30W LED Street Light Fitting with LED Each 1820.00c 60W LED Street Light Fitting with LED Each 3598.00d 120W LED Street Light Fitting with LED Each 11665.00e 150W LED Street Light Fitting with LED Each 13785.00

19 TIMER SWITCHES Havells/Equivalent

a 24 Hours Analog Timer Switch withShortest Switching Time 30 Minutes Each 2260.00

b 24 Hours Programmable Timer Switch withShortest Switching Time15 Minutes Each 2400.00

c Digital Weekly Programmable Timer Switchwith Shortest Switching Time 1 Minute Each 2250.00

d Astronomical Weekly ProgrmmableTimer Switch Each 2590.00

e Staircase Light Timer Switch AdjustableRange 5 to 20 Minutes Each 1190.00

20 63A 3 Phase 4 Pole contractor(L&T / Equivalent) Each 5276.00

21 STARTERS FOR FLUORESCENT TUBESa. Starters of capacity 20 Watts Each 9.35b. Starters of capacity 40 Watts/ 36 watts Each 9.3520 POLYSTER FILLED COPPER CHOKE 250V/

50 HZ GRADE SUITABLE FOR (PHILIPS/CROMPTON/ WIPRO / EQUIVALENT)

a. 20 Watts fluorescent Tube Each 167.90b. 40 Watts fluorescent Tube Each 167.90c. 36/40W Electronic ballast for flu. Tube

(Philips/Crompton/ Equivalent) Each 278.90d. 36/40W Electronic ballast for flu. Tube

(Indo Asean/ Equivalent) Each 227.00


183

23 CONDENSOR FOR S.V/ M.V LAMPa. 8 Mfd for 80 Watts Bulb Each 102.40b. 10 Mfd for 125 watts Bulb Each 122.60c. 15 Mfd for 250 Watts Bulb Each 163.30d. 20 Mfd for 400 watts Bulb Each 225.9024 Battern type Bakelite holder for lamp Each 16.3525 Water tight bulk head fitting suitable for 100/60 watts

lamp with guard heavy type (PHILIPS/ BAJAJ/CROMPTON GREAVES/ EQUIVALENT) Each 272.20

26 Ceiling Rose Each 13.6027 Ceiling fixtures 250/300mm complete with Gallery etc.

Clear glass opac/ crystal suitable for 40/60 Watts Bulb Each 160.8028 Ceiling Luminaire with Mirror Optics suitable for 2 Nos.

9 watts / 11 watts (Philips / Crompton /Bajaj / Equivalent) Each 1019.00(FOR ITEMS 7 TO 14,25 & 26 THE RATES AREEXCLUSIVE OF COST OF TUBES AND LAMPS)

29 Fan Clamp (Dia 12mm) with 6mmMS side plates & 45CM Cross Arm 108.80

30 CALL BELLSa. Call bell/ Buzzar 6mm suitable for AC/DC Each 40.90b. Push bell Each 16.35c. Gong bell 9” size suitable for 250 V Each 409.00d. Gong bell 12” size suitable for 250V Each 592.0031 WATER HEATER WITH ISI MARKa. Automatic Electrical Water Heater with copper container,

with Glass Wool/ Puf insulation with MS powder coatedshell suitable for 25 Litres capacity 230V/1000W(Venus/Racold/Equivalent) Each 6710.00

b. Automatic Electrical Water Heater with copper container,with Glass Wool/ Puf insulation with MS powder coatedshell suitable for 25 Litres capacity 230V/1000W(Other make ISI) Each 4968.00

c. Automatic Electrical Water Heater with copper container,with Glass Wool/ Puf insulation with MS powder coatedshell suitable for 35 litres capacity 230V/1000W(Venus/Racold/Equivalent) Each 7706.00

d. Automatic Electrical Water Heater with copper container,with Glass Wool/ Puf insulation with MS powder coatedshell suitable for 35 litres capacity 230V/1000W(Other make ISI) Each 5755.00


184

II PART ‘B’1. FANS – CONFORMING TO ISS 374 / 1979a. AC Ceiling fan complete 1200mm (48”) sweep

with 300mm Down rod.(without regulator) Each 1130.00b. AC Ceiling fan complete 1400mm (56”)

sweep with 300mm Down rod.(Without regulator) Each 1212.00

c. Stepped electronic 300W/450W squaretype fan regulator (Anchor Deluxe/Equivalent) Each 192.40

d. Dimmer type electronic 300W/450W squaretype fan regulator (Anchor Deluxe/Equivalent) Each 153.80

e. AC Ceiling fan complete 1200mm (48”)sweep with 300mm Down rod.(withoutRegulator) (Crompton/Equivalent) Each 1282.00

f. AC Ceiling fan complete 1400mm (56”)sweep with 300mm Down rod (Withoutregulator) (Crompton / equivalent) Each 1383.00

2 EXHAUST FANSa. AC Exhaust Fan 225 mm (9”) sweep

(Light duty) Each 1047.00b. AC Exhaust Fan 300 mm (12”) sweep

(Light duty) Each 1197.00c. AC Exhaust Fan 375 mm (15”) sweep

(Light duty) Each 1234.00d. AC Exhaust Fan 450 mm (18”) sweep

(Light duty) Each 1737.00e. AC Exhaust Fan 375 mm (15”) sweep

(Heavy duty) Each 2281.00f. AC Exhaust Fan 450 mm (18”) sweep

(Heavy duty) Each 2836.003 LOUVER SHUTTERS ARRANGEMENTSa. MS/Fibre Louvers shutters arrangements

for 300mm AC Exhaust Fan Each 218.60b. MS/Fibre Louvers shutters arrangements

for 375mm AC Exhaust Fan Each 231.60c. MS/Fibre Louvers shutters arrangements

for 450mm AC Exhaust Fan Each 259.204 CEILING FAN Higher End Lower End

Havells / Almonard/Crompton/ Equivalent

Usha /Equivalent

a 48" Ceiling Fan 5 Star Rated (without Regulator) Each 1,444.00 1284.00b 48" Ceiling Fan Crompton High Speed

(without Regulator) Each 1,436.00 1266.00

Item Description Unit Rates for 2020-21in Rupees

185

c BEE Energy efficient 1200mm sweep ceiling fan5 star rated, inverter driven controlled by microprocessor with 300mm down rod with regulator/remote control (35W) (Usha/Super Fan/Equivalent) Each 2597.00

5 DIMMER AND REGULATOR Higher End Lower EndCrabtree/ arbit/Logrand/ oswin/Hager/ Roma /

Equivalent Equivalenta Fan Step Regulator 100W - 1 Module Each 335.00 241.00b Fan Step Regulator 100W - 2 Module Each 382.00 275.00

III PART “C”1 SWITCHESa. 5 Amps (Flush type) Dozen 190.70b. 5 Amps (Flush type staircase) Dozen 237.002 DOUBLE POLE SWITCHES(GEM / HPL /

HAVELLS / EQUIVALENT)a. 16 Amps DP Switch with metal clad

(front handle) Each 409.00b. 32 Amps DP Switch with metal clad

(front handle) Each 839.00c. 16 Amps DP Switch with metal clad

(side handle) Each 338.00d. 32 Amps DP Switch with metal clad

(side handle) Each 761.003. TRIPLE POLE SWITCHES (SIDE HANDLE)

(STANDARD /HPL/HAVELLS/ EQUIVALENT)a. 100 Amps TPN Switch with HRC fuses

sheet steel double break Each 5755.00b. 125 Amps TPN Switch with HRC fuses

sheet steel double break Each 6310.00c. 200 Amps TPN Switch with HRC fuses

sheet steel double break Each 8157.00d. 315 Amps TPN Switch with HRC fuses

sheet steel double break Each 11570.00e. 400 Amps TPN Switch with HRC fuses

sheet steel double break Each 14900.00f. 16 Amps TPN Metal clad switch with

rewirable fuse units Each 873.00g 32 Amps TPN Metal clad switch with

rewirable fuse units Each 1290.00h 63 Amps TPN Metal clad switch with

rewirable fuse units Each 2810.00I 100 Amps Metal clad switch with

rewirable fuse units Each 5533.00j 200 Amps Metal clad switch with

rewirable fuse units Each 8400.00


186

4. SWITCH DISCONNECTOR FUSE UNITS IN SHEET

STEEL ENCLOSURE (SDF) (L&T/SIEMENS / EQUIVALENT)

a 63 A TPN switch disconnector fuse units in sheet steel

enclosure with HRC fuses Double break Each 3555.00

b 100 A TPN switch disconnnector fuse units in sheetsteel enclosure with HRC fuses Double break Each 5979.00

c 125 A TPN switch disconnnector fuse units in sheet

steel enclosure with HRC fuses Double break. Each 7059.00d 200 A TPN switch disconnnector fuse units in sheet

steel enclosure with HRC fuses Double break Each 8867.00

e 250 A TPN switch disconnnector fuse units in sheetsteel enclosure with HRC fuses Double break Each 11059.00

f. 315 A TPN switch disconnnector fuse units in sheet

steel enclosure with HRC fuses Double break Each 13261.00g 400 A TPN switch disconnnector fuse units in sheet

steel enclosure with HRC fuses Double break Each 15210.00

5 SWITCH DISCONNECTOR FUSE UNITS IN OPEN

EXECUTION (INTERIOR FOR CUBICAL)

(L&T/SIEMENS / EQUIVALENT)

a 63A TPN Switch disconnector fuse units interior onlywith HRC fuses Double break Each 2349.00

b 100 A TPN switch disconnnector fuse units interior

only with HRC fuses Double break. Each 4272.00c 125 A TPN switch disconnector fuse units interior

only with HRC fuses Double break. Each 5827.00

d 200 A TPN switch disconnector fuse units interioronly with HRC fuses Double break. Each 7519.00

e 250 A TPN switch disconnector fuse units interior

only with HRC fuses Double break. Each 9797.00f. 315 A TPN switch disconnector fuse units interior

only with HRC fuses Double break. Each 12322.00

g 400 A TPN switch disconnector fuse units interior onlywith HRC fuses Double break. Each 14533.00

6 FUSE UNITS (ANCHOR /EQUIVALENT)

a. 16 Amps Porcelain fuse unit (500 V) Each 47.20b. 32 Amps Porcelain fuse unit (500 V) Each 83.60


187

c. 63 Amps Porcelain fuse unit (500 V) Each 186.60d. 100 Amps Porcelain fuse unit (500 V) Each 337.00e. 200 Amps Porcelain fuse unit (500 V) Each 545.007 SINGLE PHASE DBS (GEM /EQUIVALENT)

a. 4 Way DB 16 Amps /Way with fuse &Neutral Each (250V) Each 454.00

b. 6 Way DB 16 Amps /Way with fuse & Neutral Each (250V) Each 619.00c. 8 Way DB 16 Amps /Way with fuse & Neutral Each (250V) Each 766.008 THREE PHASE DBS(GEM /EQUIVALENT)

a. 4 Way TPDB 16A/Way with fuse & Neutral link Each 1792.00b. 6 Way TPDB 16A/Way with fuse & Neutral link Each 2454.00c. 8 Way TPDB 16A/Way with fuse & Neutral link Each 2969.00d. 4 Way TPDB 32A/Way with fuse & Neutral link Each 2267.00e. 6 Way TPDB 32A/Way with fuse & Neutral link Each 3033.00f. 8 Way TPDB 32A/Way with fuse & Neutral link Each 3836.00g. 4 Way TPDB 63A/Way with fuse & Neutral link Each 5305.00h. 6 Way TPDB 63A/Way with fuse & Neutral link Each 6824.009 CHANGE OVER SWITCHES(GEM /HAVELLS /

HPL/STANDARD /EQUIVALENT)

a. 16 Amps three phase 500 V 4 pole Change over switch Each 1234.00b. 32 Amps three phase 500 V 4 pole Change over switch Each 1462.00c. 63 Amps three phase 500 V 4 pole Change over switch Each 3194.00d. 100 Amps three phase 500 V 4 pole Change over switch Each 5077.00e. 200 Amps three phase 500 V 4 pole Change over switch Each 9552.00

CHANGE OVER SWITCH (L&T / Equivalent)

f 250A 3 phase 4 pole change over switch Each 20216.00g 400A 3 phase 4 pole change over switch Each 30886.0010 MODULAR SWITCHES Unit Higher End Lower End

Crabtree / Orbit /legrand / Oswin /Hager / ROMA /

Equivalent Equivalent

1 Switches 6A - 230V

a 6A Switch 1W - 1 Module Each 76.70 56.50

b 6A Switch 2W - 1 Module Each 93.70 66.60c 6A Switch 1W - 1 Module with Indicator Each 103.00 73.50


188

d 6A Switch 1W - 1 Module with ‘Light’ Marking Each 82.70 59.00

e 6A Switch 1W - 1 Module with ‘Fan’ Marking Each 82.70 59.00

2 Switches 16A - 230V

a 16A Switch 1W - 1 Module Each 115.70 82.70

b 16A Switch 2W - 1 Module Each 142.80 103.00

c 16A Switch 1W with Indicator - 1 Module Each 136.00 98.003 Switches 20A - 230V

a 20A 1W Switch - 1 Module Each 150.30 108.10

b 20A DP 1W Switch - 2 Module Each 250.90 179.30c 20A DP 1W Switch with Indicator - 2 Module Each 264.40 190.70

4 Switches 25A - 230V Each

a 25A SP 1W Switch with Indicator - 1 Module Each 163.60 118.105 Switches 32A - 230V Each

a 32A DP Switch with Indicator - 2 Module Each 319.00 231.20

11 PUSH BUTTONS

a 6A Push Button SP - 1 Module Each 103.70 75.10

b 6A Push Button SP with Indicator - 1 Module Each 134.80 97.10

c 6A Bell Push - 1 Module Each 103.00 73.50d 6A Bell push with Indicator - 1 Module Each 127.50 91.20

e 6A Bell Push - 2 Module Each 134.80 97.10

f 6A Bell Push with Indicator - 2 Module Each 158.60 114.0012 MOTOR STARTER

a 25A Motor Starter - 2 Module Each 295.90 213.00

13 FLUSH MOUNTING BOXES (GI) Eacha Flush Box - 1/2 Module Each 38.00 27.50

b Flush Box - 3 Module Each 44.60 32.40

c Flush Box - 4 Module Each 54.40 38.90d Flush Box - 6 Module Each 85.30 61.70

e Flush Box - 8 Module Each 104.70 75.50

f Flush Box - 8 Module (2 row x 4) Each 105.50 76.30g Flush Box-12/16 (2 row x 6) Module Metal Box Each 141.40 101.60

h Flush Box - 18 Module Metal Box 160.80 115.40

14 SURFACE MOUNTING BOXES (PLASTIC)

a Surface Box - 1/2 Module Each 42.20 30.00

b Surface Box - 3 Module Each 44.60 32.40

c Surface Box - 4 Module Each 57.60 41.30

Rates for 2020-21Item Description Unit in Rupees

189

d Surface Box - 6 Module Each 74.70 54.40

e Surface Box - 8 Module Each 91.00 65.80

f Surface Box - 8 (2 row x 4) Module Each 105.60 76.30

g Metal Surface Box - 12/16 (2 row x 6) Module Each 160.00 115.00

h Metal Surface Box - 18 Module Each 204.00 146.30

15 COMBINED PLATES (PLASTIC)

a 1 Module Cover Plate Each 62.50 45.40

b 2 Module Cover Plate Each 65.80 47.00

c 3 Module Cover Plate Each 79.50 56.70

d 4 Module Cover Plate Each 88.50 63.30

e 6 Module Cover Plate Each 124.30 89.30

f 8 Module Cover Plate Each 158.40 113.70

g 8 Module Cover Plate (H) Each 159.20 134.70

h 12 Module Cover Plate Each 198.30 143.10

i 18 Module Cover Plate Each 250.40 179.50

16 COMBINED PLATES (ALUMINIUM) Each

a 1 Module Cover Plate Each 127.50 91.80

b 2 Module Cover Plate Each 134.00 93.70

c 3 Module Cover Plate Each 145.40 104.80

d 4 Module Cover Plate Each 164.10 117.80

e 6 Module Cover Plate Each 278.90 201.60

f 8 Module Cover Plate Each 308.00 222.80

g 8 Module Cover Plate (H) Each 391.80 282.00

h 12 Module Cover Plate Each 509.00 367.00

i 18 Module Cover Plate Each 671.00 483.00

17 SOCKET - 230V Higher End Lower End

Crabtree / Orbit /

legrand / Oswin /

Hager / ROMA /


a 16A 3 Pin Switched Socket - 3 Module Each 380.00 274.50

b 6A 5 pin Universal Socket - 2 Module Each 118.10 85.80

c 6/16A Socket - 3 Module Each 214.00 154.40

d 6/16A Socket - 2 Module Each 181.70 130.20


190

IV PART ‘D’

1 PLUG AND SOCKETS

a 5 Amps 3 pin and 2 pin combinedflush type wall socket only. Each 23.70

b 5 Amps /15 amps.3 pin flush type wall socket only. Each 53.50

c 5 Amps 3 pin Top Each 33.60d 15 Amps 3 pin Top Each 47.60

e 15 Amps Flush type switch Each 55.50

f 10 Amps M.C plug with 3 pin Top Each 177.30g 20 Amps M.C plug with 3 pin Top Each 202.00

h 25A Flush type Wall Socket with

25A DP MCB for AC Plug Each 795.802 SINGLE PHASE WATT HOUR METERS

[HPL/EQUIVALENT)

a. AC single phase 230V/250V/50 HZ 5 AmpsWatt Hour Meter Each 945.00

b. AC single phase 230V/250V/50 HZ 10 Amps

Watt Hour Meter Each 945.00c. AC single phase 230V/250V/50 HZ 20 Amps

Watt Hour Meter Each 945.00

3 THREE PHASE WATT HOUR METERS

(ANCHOR / EQUIVALENT)

a. AC 3 phase 400V 50 HZ unbalanced load

4 wire 10 Amps Watt Hour Meter Each 1949.00b. AC 3 phase 400V 50 HZ unbalanced load

4 wire 25 Amps Watt Hour Meter Each 1949.00

c. AC 3 phase 400 V 50 HZ unbalanced load4 wire 50 Amps Watt Hour Meter Each 2468.00

V PART ‘E’

I SERVICE CONNECTION ACCESSORIES

LT. 1100V PVC ALUMINIUM ARMOURED

UNDER GROUND CABLE WITH ISI MARK

a. 2 Core 6 sq.mm PVC armoured UG cable Metre 86.40b. 2 Core 10 sq.mm PVC armoured UG cable Metre 105.20

c. 2 Core 16 sq.mm PVC armoured UG cable Metre 114.20

d. 2 Core 25 sq.mm PVC armoured UG cable Metre 129.70


191


e 31/2 core 25 sq.mm. PVC Armoured UG Cable Metre 195.50

f 31/2 core 35 sq.mm. PVC Armoured UG Cable Metre 230.10

g 31/2 core 50 sq.mm. PVC Armoured UG Cable Metre 299.80h 31/2 core 70 sq.mm. PVC Armoured UG Cable Metre 384.50

i 31/2 core 95 sq.mm. PVC Armoured UG Cable Metre 497.70

j 31/2 core 120 sq.mm. PVC Armoured UG Cable Metre 607.90k 31/2 core 150 sq.mm. PVC Armoured UG Cable Metre 720.00

l 31/2 core 185 sq.mm. PVC Armoured UG Cable Metre 879.00

m 31/2 core 240 sq.mm. PVC Armoured UG Cable Metre 1115.00n 31/2 core 300 sq.mm. PVC Armoured UG Cable Metre 1368.00

o 31/2 core 400 sq.mm. PVC Armoured UG Cable Metre 1744.00

p 4 core 6 sq.mm. PVC Armoured UG Cable Metre 111.90q 4 core 10 sq.mm. PVC Armoured UG Cable Metre 122.70

r 4 core 16 sq.mm. PVC Armoured UG Cable Metre 161.70

2 PVC INSULATED SINGLE CORE MULTI STRAND FIRE

RETARDANT FLEXIBLE COPPER CABLE WITH ISI

MARK CONFORMING TO IS 694/ 1990

a. 14/0.3 ( 1 sq.mm ) Metre 8.55b. 22/0.3 ( 1.5 sq.mm ) Metre 13.50

c. 36/0.3 ( 2.5 sq.mm ) Metre 21.00d. 56/0.3 ( 4 sq.mm ) Metre 33.30

e. 84/0.3 ( 6 sq.mm ) Metre 49.30

f. 140/0.3 ( 10 sq.mm ) Metre 74.20g. 101/0.45 ( 16 sq.mm ) Metre 121.30

h. 168/0.45 ( 25 sq.mm ) Metre 266.50

3 CONDUCTOR

a. Hard drawn copper conductor(Gauge No.8 & 6) KG 500.00

b. 14 SWG TC wire KG 513.00

c. GI No.8 wire and No. 6 wire KG 82.604 CABLE GLANDS

a. Cable gland suitable for 2 core 4 sq.mm UG cable Each 18.00

b. Cable gland suitable for 2 core 6 sq.mm UG cable Each 22.50c. Cable gland suitable for 2 core 10 sq.mm UG cable Each 26.90

d. Cable gland suitable for 2 core 16 sq.mm UG cable Each 39.80

e. Cable gland suitable for 2 core 25 sq.mm UG cable Each 47.60f. Cable gland suitable for 3½ core 25 sq.mm UG cable Each 47.60

192


g. Cable gland suitable for 3½ core 35 sq.mm UG cable Each 60.50h. Cable gland suitable for 3½ core 50 sq.mm UG cable Each 60.50

i Cable gland suitable for 3½ core 70 sq.mm UG cable Each 74.60

j Cable gland suitable for 3½ core 95 sq.mm UG cable Each 91.10k Cable gland suitable for 3½ core 120 sq.mm UG cable Each 116.00

l Cable gland suitable for 3½ core 150 sq.mm UGcable Each 152.70

m Cable gland suitable for 3½ core 185 sq.mm UGCable Each 180.60n Cable gland suitable for 3½ core 240 sq.mm UG cable Each 180.60

o Cable gland suitable for 3½ core 300 sq.mm UGcable Each 215.70

p Cable gland suitable for 3 ½ core 400 sq.mm UGcable Each 306.90q Cable gland suitable for 3 ½ core 500 sq.mm UG cable Each 357.80

r Cable gland suitable for 4 core 6 sq.mm UG cable Each 22.50

s Cable gland suitable for 4 core 10 sq.mm UG cable Each 26.90t Cable gland suitable for 4 core 25 sq.mm UG cable Each 47.60

5 FUSE WIRE(COPPER)

a. 5 Amps fuse wire Kg 500.00b. 10 Amps fuse wire Kg 500.00

c. 20 Amps fuse wire Kg 500.006 NEUTRAL LINK 15 AMPS

a. 4 way Neutral Link Each 24.80

b. 6 way Neutral Link Each 36.70c. 8 way Neutral Link Each 45.80

d. 12 way Neutral Link Each 66.60

VI PART ‘ F ‘

1 M.S. BOX WITH PAINTING (16 SWG)

a. M.S Box of Size (100 x 100 x 75mm) Each 39.70

b. M.S Box of Size (150 x 100 x 75mm) Each 54.90c. M.S Box of Size (200 x 150 x 75mm) Each 89.30

d. M.S Box complete with Lock & Key arrangements with

painting of size (300 x 200 x 100 mm) Each 270.002 Synthertic Moulded Coumpound box for street light Each 735.00

VII PART ‘ G ‘

1 MS ANGLES

a. 1½ “ x 1½” x 1/4" (37.5 x 37.5 x 6.24 mm)(1M=3.25Kg) KG 44.70

b. 1½”x 1½” x ½” (37.5 x 37.5 x 12.5mm) KG 44.70

c. 2" x 2" x ½” (50 x 50 x 12.5 mm) KG 44.70

193


2 ALUMINIUM FLAT

a. Aluminium Flat (1"x 1/4") (25x 6.25 mm) KG 155.80

b. Aluminium Flat ( 1"x1/8") KG 155.80

3 COPPER FLAT

a. Copper Flat (25 x 3 mm) KG 458.00

b. Copper Flat (25 x 6 mm) KG 458.00

c. Copper Flat (33 x 6 mm) KG 458.00d. Copper Flat (50 x 6 mm) KG 458.00

4 POWER CAPACITOR

a. Power capacitor for power factor improvement withoil filled with discharge resistance 3 phase 415/440V

50 HZ conforming to ISS:2834 with ISI marking KVAR 312.00

VIII PART ‘ H ‘

1 CONDUIT MATERIALS 16 Gauge

a. Conduit pipe 16 mm (5/8") Heavy Gauge Metre 27.20

b. Conduit pipe 19 mm (3/4") Heavy Gauge Metre 28.10c. Conduit pipe 25 mm (1") Heavy Gauge Metre 34.60

d. Conduit pipe 32 mm (1¼”) Heavy Gauge Metre 45.40e. Conduit pipe 38 mm (1½”) Heavy Gauge Metre 53.50

2 CONDUIT TEE BENDS

a. Conduit Tee bends 16 mm (5/8") Dozen 76.30b. Conduit Tee bends 19 mm (3/4") Dozen 77.10

c. Conduit Tee bends 25 mm (1") Dozen 92.60

d. Conduit Tee bends 32 mm (1¼”) Dozen 95.80e. Conduit Tee bends 38 mm (1½”) Dozen 119.40

f. Conduit Tee bends 50 mm (2") Dozen 149.20

3 CONDUIT BENDS 16 Gauge

a. Conduit solid bends 16 mm (5/8") Dozen 72.20

b. Conduit solid bends 19 mm (3/4") Dozen 80.40

c. Conduit solid bends 25 mm (1") Dozen 95.00d. Conduit solid bends 32 mm (1¼”) Dozen 112.20

e. Conduit solid bends 38 mm (1½”) Dozen 159.20

f. Conduit solid bends 50 mm (2") Dozen 194.904 CONDUIT INSPECTION BEND 16 Gauge

a. Conduit Inspection bends 16 mm (5/8") Dozen 72.20

b. Conduit Inspection bends 19 mm (3/4") Dozen 74.70

194


c. Conduit Inspection bends 25 mm (1") Dozen 95.80d. Conduit Inspection bends 32 mm (1 ¼”) Dozen 115.40

e. Conduit Inspection bends 38mm (1½”) Dozen 149.40

f. Conduit Inspection bends 50mm (2") Dozen 169.80g. Conduit Inspection bends 65mm (2½”) Dozen 218.60

5 HDPE Pipe

a. HDPE pipe 50mm/ 38mm RM 101.00b. HDPE pipe 90mm/ 76mm RM 208.00

c. HDPE pipe 120mm/ 103.50mm RM 259.50

6 Cable Tray Manibhadra/

Equivalent

a. GI Hot dip/ Powder coated 16 SWG Cable tray

with 150mm width and 50mm height RM 322.00b. GI Hot dip/ Powder coated 16 SWG Cable

tray with 300mm width and 50mm height RM 393.00

IX PART ‘ I ‘

1 PVC (RIGID) PIPES (1.8 MM THICK)

WITH ISI MARK (Building)

a. PVC rigid pipes 16mm (5/8") Metre 11.70

b. PVC rigid pipes 20mm (3/4") Metre 17.10

c. PVC rigid pipes 25mm (1") Metre 25.40d. PVC rigid pipes 32mm (1¼”) Metre 38.40

e. PVC rigid pipes 40mm (1½”) Metre 54.90

f. PVC rigid pipes 50mm (2") Metre 82.202 PVC RIGID BENDS

a. PVC rigid bends 16mm (5/8") Each 2.70

b. PVC rigid bends 20mm (3/4") Each 2.70c. PVC rigid bends 25mm (1") Each 3.70

d. PVC rigid bends 32mm (1¼”) Each 6.60

e. PVC rigid bends 40mm (1½”) Each 16.50f. PVC rigid bends 50mm (2") Each 20.10

3 PVC COUPLES

a. PVC Couples 16mm (5/8") Dozen 11.80b. PVC Couples 19mm (3/4") Dozen 11.80

c. PVC Couples 25mm (1") Dozen 23.00

d. PVC Couples 32mm (1¼”) Dozen 52.60

195


e. PVC Couples 38mm (1½”) Dozen 112.70f. PVC Couples 50mm (2") Dozen 117.704 PVC TEES

a. PVC Tees 16mm (5/8") Dozen 11.80b. PVC Tees 19mm (3/4") Dozen 13.70c. PVC Tees 25mm (1") Dozen 17.50d. PVC Tees 32mm (1¼”) Dozen 78.50e. PVC Tees 38mm (1½”) Dozen 252.00f. PVC Tees 50mm (2") Dozen 276.005 PVC Saddles

a. PVC Saddles 16 mm (5/8") Dozen 2.70b. PVC Saddles 19mm (3/4") Dozen 3.10c. PVC Saddles 25mm (1") Dozen 3.60d. PVC Saddles 32mm (1¼”) Dozen 4.50e. PVC Saddles 38mm (1½”) Dozen 5.50f. PVC Saddles 50mm (2") Dozen 11.006 PVC JUNCTION BOXES

a. Junction boxes 1,2,3 & 4 way 16 mm (5/8") Dozen 36.80b. Junction boxes 1,2,3 & 4 way 19 mm (3/4") Dozen 36.80c. Junction boxes 1,2,3 & 4 way 25 mm (1") Dozen 43.30d. Junction boxes 1,2,3 & 4 way 32 mm (1¼”) Dozen 96.20e. Junction boxes 1,2,3 & 4 way 38 mm (1½”) Dozen 114.307 PVC Hylem sheets

a. Hylem sheet 3 mm thick Sq.m 563.008 Insulation Tape PVC

a. PVC Insulation Tape (19mm) Roll/10 mts 13.70b. Empire Tape (12 mm) Roll/10 mts 18.40c. Empire Tape (19 mm) Roll/10 mts 22.10X PART ‘ J ‘

1 TEAK WOOD MATERIALS

T.W. BOX CONCEALED TYPE

a. T.W. Box concealed type 12"x8"x3" Each 69.90b. T.W.Box concealed type 8"x6"x3" Each 37.10c. T.W. Box concealed type 6"x4"x3” Each 16.50d. T.W. Box concealed type 4"x4"x3” Each 13.80e. T.W. plugs 1½” x 1" x2" 1000 Nos. 287.00f. T.W. Round blocks 100 Nos. 558.00

196


XI PART ‘ K ‘

1 CRIMPING LUGS SUITABLE FOR THE FOLLOWING SIZES

Size Unit Aluminium Copper

a. 4 Sq.mm Unit 1.27 3.89

b. 6 Sq.mm Unit 1.42 3.89c. 10 Sq.mm Unit 1.84 4.90

d. 16 Sq.mm Unit 1.84 5.90

e. 25 Sq.mm Unit 2.80 9.85f. 35 Sq.mm Unit 3.70 10.85

g. 50 Sq.mm Unit 5.55 12.80

h. 70 Sq.mm Unit 7.40 20.80i. 95 Sq.mm Unit 8.40 25.80

j. 120 Sq.mm Unit 11.25 35.65

k. 150 Sq.mm Unit 15.00 45.60l. 185 Sq.mm Unit 19.60 69.45

m. 225 Sq.mm Unit 29.10 99.10

n. 240 Sq.mm Unit 31.90 99.10o. 300 Sq.mm Unit 44.10 133.70

p. 400 Sq.mm Unit 65.90 203.20

2 CABLE ROUTE INDICATOR

a. Cable route indicator for L.T cable Each box 66.20

b Cable route indicator for H.T cable Each box 66.20

XII PART ‘ L ‘

1 BRASS SCREWS

a. Brass Screws (20mm) ¾” No.6 Gross 59.10

b Brass Screws (25mm) 1" No.6 Gross 63.70c. Brass Screws (40mm) 1½” No.6 Gross 68.20

d. Brass Screws (20mm) 3/4" No.8 Gross 59.10

e. Brass Screws (25mm) 1" No.8 Gross 63.70f. Brass Screws (50mm)2" No.10 Gross 131.70

g. Brass screws (75mm)3" No.10 Gross 194.90

2 Coach screws 2"x¼” (50 x 6.25mm) Dozen 11.703 CONDUIT SADDLES

a. Conduit Saddles 16mm (5/8") Gross 36.30

b. Conduit Saddles 19mm (3/4") Gross 38.70c. Conduit Saddles 25mm (1") Gross 45.40

197


d. Conduit Saddles 32mm (1¼”) Gross 59.10e. Conduit Saddles 38mm (1½”) Gross 72.50

f. Conduit Saddles 50mm (2") Gross 81.90

g. Conduit Saddles 65mm (2½”) Gross 93.304 SODIUM VAPOUR FITTINGS & LAMP

(For External Electrification & Campus lighting)

a. 250 Watts Sodium Vapour fittings Each 2997.00b 250 Watts Sodium Vapour lamp Each 662.00

c. 150 Watts Sodium Vapour fittings Each 2954.00

d. 150 Watts Sodium Vapour lamp Each 567.00e. 70 Watts Sodium Vapour fittings Each 2383.00

f. 70 Watts Sodium Vapour lamp Each 377.00

5 SODIUM VAPOUR LAMP FITTING SINGLE PIECE DIE

CAST ALUMINIUM HOUSING & LAMP FOR HEAVY

TRAFFIC ROADS (PHILIPS/ CROMPTON CREAVES/

WIPRO/BAJAJ/ EQUIVALENT)

a. 400 Watts sodium vapour fittings Each 8958.00

b 400 Watts sodium vapour lamp Each 929.00

c. 250 Watts sodium vapour fittings Each 6110.00d. 250 Watts sodium vapour lamp Each 751.00

e. 150 Watts sodium vapour fittings Each 5736.00

f. 150 Watts sodium vapour lamp Each 617.00g. 70 Watts sodium vapour fittings Each 2454.00

h. 70 Watts sodium vapour lamps Each 425.00

6 MINIATURE CIRCUIT BREAKERS 240 V/415 V 50HZ Legrand/ All other

AC SUPPLY SUITABLE FOR BOTH LIGHTING Hager / makes

AND MOTOR CIRCUITS. Equivalent with

(Each) ISI (Std.)

/ HPL /

Havells /

Equivalent)

(Each)

a. Single pole 6A to 32A,10 KA 172.00 126.00

b Single pole 40A , 10 KA 354.00 263.00c. Single pole & Neutral 6A to 32A, 10 KA 506.00 382.00

d. Single pole & Neutral 40A, 10 KA 821.00 530.00

198


e. Double pole 6A to 32A, 10 KA Each 506.00 420.00

f. Double pole 40A, 10 KA Each 821.00 576.00g. Triple pole 6A to 32A, 10 KA Each 814.00 635.00

h. Triple pole 63A , 10 KA Each 1239.00 1011.00

I Triple pole & Neutral 6A to 32A, 10 KA Each 1072.00 827.00j. Triple pole & Neutral 63A, 10 KA Each 1601.00 1275.00

k. Four pole 6A to 32A, 10 KA Each 1072.00 886.00

l. Four pole 63A, 10 KA Each 1601.00 1358.007 PLUG AND SOCKETS IN SHEET STEEL Legrand/ All other

ENCLOSURE WITHOUT MCBS Hager / makes

Equivalent with

(Each) ISI (Std.)

/ HPL /

Havells /

Equivalent)

(Each)

All other Makes with ISI (Std)/ HPL/

Havell’s/ equivalent) (Each)

a. 10A single Pole Each 838.00 496.00

b 20A Single Pole Each 895.00 502.00c. 20A Double Pole Each 969.00 -

d. 20A Triple Pole Each 1643.00 953.00

e. 32A Triple Pole Each 1960.00 1290.00f. 63A Triple Pole Each 7986.00 -

8 Sheet Steel Enclosure for MCB’s Legrand/ Havells/


a 2 Pole Each 371.00 258.00

b 4 pole Each 544.00 316.00

9 RCCB/ ELCB

a. 10 Amps 30 MA DP Each 2364.00 1737.00

b 25 Amps 30 MA DP Each 1949.00 1492.00

c. 40 Amps 30 MA DP Each 2157.00 1576.0010 RCCB/ELCB (FOUR POLE)

a. 25 Amps 30 MA Each 2685.00 1840.00

b 40 Amps 30 MA Each 2716.00 1882.00

c. 63 Amps 30 MA Each 3142.00 2136.00

199

11 HRC FUSES

a. 16 Amps Each 60.50 29.50b 32 Amps Each 62.80 49.50c. 63 Amps Each 129.50 62.40d. 125 Amps Each 302.00 138.40e. 160 Amps Each 377.00 186.60f. 200 Amps Each 389.00 186.60g. 250 Amps Each 541.00 275.7012 MCB ISOLATORS Legrand All other

(MDS) / makes withHager ISI (Std.)(L&T)/ / HPL

Equivalent /Havells /(Each) Equivalent)

(Each)a 32A -DP Each 265.60 -b 32A - TP Each 444.00 -c 32A -FP Each 508.00 -d 40A -DP Each 367.00 254.00e 40A - TP Each 636.00 467.00f 40A -FP Each 818.00 570.00g 63A -DP Each 492.00 323.00h 63A - TP Each 840.00 509.00i 63A -FP Each 895.00 595.00j 100A -DP Each - 417.00k 100A - TP Each 923.00 663.00l 100A -FP Each 943.00 725.00

13 MCCB L&T/

Equivalent

a 400A Spreader Terminal Each 2787.00b Rotary handle for 400A/ 630A Each 2272.00c 250A Spreader Terminal Each 1368.00d Rotary handle for 250A/ 125A Each 1392.00e 630A Spreader Terminal Each 3270.00f 400A Spreader Terminal Each 1940.00g Spreader Terminal for 250A/ 125A Each 1127.00


200


XIII PART “M”

1 11 KV INDOOR VACCUM CIRCUIT BREAKER Megawin/

Pentagon/(OEM)

a 11 KV, 25 KA, 630 A, HT Indoor Single Panel VaccumCircuit Breaker complete as per specification Each 405000.00

b 11 KV, 25 KA, 630 A, HT Indoor Three PanelVaccum Circuit Breaker complete as per specification Each 1031000.00

c 11 KV, 25 KA, 630 A, HT Indoor Four PanelVaccum Circuit Breaker complete as per specification Each 1463000.00

d 11 KV, 25 KA, 630 A, HT Indoor Five PanelVaccum Circuit Breaker complete as per specification Each 1754000.00

2 11 KV OUTDOOR VACCUM CIRCUIT BREAKER Megawin/Pentagon/

(OEM)a 11 KV, 25 KA, 630 A, HT Outdoor Single Panel

Vaccum Circuit Breaker complete as per specification Each 423000.00b 11 KV, 25 KA, 630 A, HT Outdoor Three Panel Vaccum

Circuit Breaker complete as per specification Each 1057000.00c 11 KV, 25 KA, 630 A, HT Outdoor Four Panel Vaccum

Circuit Breaker complete as per specification Each 1480000.00d 11 KV, 25 KA, 630 A, HT Outdoor Five Panel Vaccum

Circuit Breaker complete as per specification Each 1772000.003 11 KV INDOOR RING MAIN GEAR (RMG) Megawin /

Voltech /(OEM)

a 11 KV, 25 KA, 630 A, HT Indoor Three Panel Ring MainGear complete as per specification Each 589000.00

4 11 KV OUTDOOR RING MAIN GEAR (RMG) Megawin / Voltech /

(OEM)a 11 KV, 25 KA, 630 A, HT Outdoor Three Panel Ring

Main Gear complete as per specification Each 617000.005 HT CABLES Polycab /

Equivalenta 240 sq.mm. 3 core HT XLPE 11KV (E)

SISMV11E3 x 2402797 Mtr 1710.00b 300 sq.mm. 3 core HT XLPE 11KV (E)

SISMV11E3 x 3002797 Mtr 1990.00c 300 sq.mm. 3 core HT XLPE 11KV (UE)

SISMV11U3 x 3002424 Mtr 2333.00

201


6 CABLES, ACCESSORIES AND KITS Raychem

RPG /

Equivalent

a 120-185 sq.mm. 3 core HT Cable IndoorTerminations XLPE 11KV (E) - EPKT 3111 Each 9583.00

b 240-300 sq.mm. 3 core HT Cable Indoor TerminationsXLPE 11KV (E) - EPKT 3121 Each 10220.00

c 120-185 sq.mm. 3 core HT Cable Outdoor TerminationsXLPE 11KV (E) - EPKT 3362 Each 13230.00

d 240-300 sq.mm. 3 core HT Cable Outdoor TerminationsXLPE 11KV (E) - EPKT 3372 Each 14880.00

e 240-400 sq.mm. 3 core HT Cable Indoor Terminations11 KV (UE) - Belted PILC Cables - EPKT 4685 Each 13500.00

f 240-400 sq.mm. 3 core HT Cable Outdoor Terminations11 KV (UE) - Belted PILC Cables - EPKT 4961 Each 17900.00

g 150-185 sq.mm. 3 core HT Cable Outdoor Terminations22KV(E) Screened XLPE Cables - EPKT 5363 Each 18980.00

h 240-400 sq.mm. 3 core HT Cable Outdoor Terminations22KV(E) Screened XLPE Cables-EPKT 5373 Each 25250.00

i 185-240 sq.mm 3 core HT Cables Straight ThroughJoints 22KV (E) Screened XLPE Cables-EPKJ 5118 Each 49690.00

j 300-400 sq.mm. 3 core HT Cable Straight ThorughJoints 22KV (E) Screened XLPE Cables - EPKJ 5119 Each 55440.00PART “N”

1 SUPPLY & INSTALLATION OF 3 Star 5 Star

AIR-CONDITIONER WITH COPPER COIL Rated (Each)(Carrier / RatedVoltas / Inverter

Blue Star / (Carrier /Equivalent) Voltas /O

General/Equivalent)

a 1.5 TR Split Type AC Unit Each 31100.00 41400.00b 2.0 TR Split Type AC Unit Each 41400.00 52800.00c Supply and installation of 4 KVA capacity

Automatic Voltage Stabilizer with time delayrelay (V-Gurad / Equivalent) Each 4160.00

d Supply and installation of 5 KVA capacityAutomatic Voltage Stabilizer with time delayrelay (V-Gurad / Equivalent) Each 4625.00

Unit

202


e Supply and laying of 5/8" and 3/8" copper pipe(Extra beyond 3 metres supplied with AC unit) Each 880.00

f Supply and fixing of MS stand for fixing outdoor unit Each 1020.002 SUPPLY, INSTALLATION, TESTING, COMMISSIONING

AND HANDING OVER OF AIR- COOLED SELF

CONTAINED DUCTABLE AC UNITS ETA (OEM)

a 3.0 TR Ceiling Supsended Ductable Unit Each 91900.00b 5.5 TR Ceiling Supsended Ductable Unit Each 158500.00c 8.5 TR Ceiling Supsended Ductable Unit Each 216000.00d 11 TR Ceiling Supsended Ductable Unit Each 278700.00e 17 TR Ceiling Supsended Ductable Unit Each 404000.00f 5.5 TR Floor Mounted Ductable Unit Each 335000.00g 8.5 TR Floor Mounted Ductable Unit Each 346000.00h 11 TR Floor Mounted Ductable Unit Each 380000.00i 17 TR Floor Mounted Ductable Unit Each 543000.00j 25 TR Floor Mounted Ductable Unit Each 653000.003 ACCESSORIES FOR PACKAGE AC

a Supply and filling of R-22 Refrigerant Gas KG 536.00b Supply and fixing of Copper Refrigerant Piping of 7/8" dia RM 972.00c Supply and fixing of Flexible Canvas Connection Each 2592.00d Supply and fixing of 50mm thick Anti Vibrating

Rubber Pads Sqm. 509.00e Supply, Fabrication and erection of fabricated ducting

made up of GI Sheets of 24 Gauge thickness RM 795.00f Supply, Fabrication and erection of fabricated ducting

made up of GI sheets of 22 Gauge thickness Sqm. 1064.00g Supply, Fabrication and erection of fabricated ducting

made up of GI sheets of 20 Gauge thickness Sqm. 1323.00h Supply and fixing of extruded aluminum powder coated,

Supply and return Air Grilles / Diffusers with VolumeControl Damper Sqm. 7408.00

i Supply and fixing of water drain pipe line (1” PVC Pipe) RM 60.00j Supply, fabrication and fixing of MS Channel for

Mounting the Airconditioning Indoor Unit Each 6852.00k Supply, fabrication and fixing of Ms Channel for

Mounting the Airconditioning Oudoor Unit Each 5832.00l Supply and providing of pipeline nitrle rubber insulation

for Refrigerant and drain pipe lines. RM 51.80m Supply and fixing of Duct Mouth Dampers Set 2220.00

203


n Supply and providing acoustic for initial portion ofducting with 12mm thick Fibre Glass Rigid Board coveredwith Tissue Paper and Aluminum Perforated Sheet Sqm. 788.00

o Supply and providing thermal insulation of 9mm thickvidoflex with Aluminum Foil Sqm. 768.00

p Supply and providing Civil Concrete Block forMounting the Airconditioning Unit Each 660.00

q Supply and laying of 30 sq.mm. incoming cable RM 358.00r Supply and providing of 10 sq.mm.

copper flexible single cable RM 82.80s Supply and providing of 1.5 sq.mm. copper flexible cable RM 18.50t Supply and providing of 0.5 sq.mm. 4 core

flexible signal cable RM 15.504 GENERATORS WITH STANDARD PANEL Kirloskar

/ AshokLeyland /Equivalent

a 5 KVA Each 192500.00b 7.5 KVA Each 200900.00c 10 KVA Each 227200.00d 15 KVA Each 244100.00e 20 KVA Each 256700.00f 30 KVA Each 312400.00g 35 KVA Each 333600.00h 40 KVA Each 389300.00i 45 KVA Each 454600.00j 62.5 KVA Each 522900.00k 82.5 KVA Each 616700.00l 100 KVA Each 686000.00m 125 KVA Each 788200.00n 160 KVA Each 1071000.00o 200 KVA Each 1308000.00p 250 KVA Each 1473000.005 GENERATORS WITH AUTO MAIN FAILURE Kirloskar

(AMF) PANEL / Ashok

Leyland /

Equivalent

a 62.5 KVA Each 628200.00b 82.5 KVA Each 721900.00c 100 KVA Each 896500.00

204


d 125 KVA Each 998600.00e 160 KVA Each 1281700.00f 200 KVA Each 1518600.00g 250 KVA Each 1683800.006 Exhaust Pipe with Silencer RM 2074.007 PASSENGER LIFTS (G+3) Johnson /

SS 304 Grade with 1m/sec. speed with ARD Kone /

OTIS/

Equivalent

A 8 Persons Passenger Lift Car Size (1300 x 1100)

a Gearless Lift with Machine Room Each 1429000.00b Gearless Lift without Machine Room Each 1496000.00B 10 Persons Passenger Lift Car Size (1300 x 1350) Johnson

/Kone /

OTIS/

Equivalent

a Gearless Lift with Machine Room Each 1493000.00b Gearless Lift without Machine Room Each 1565000.00C 13 Persons Passenger Lift Car Size (2000 x 1100) Johnson/

Kone /

OTIS/

Equivalent

a Gearless Lift with Machine Room Each 1662000.00b Gearless Lift without Machine Room Each 1739000.00D 20 Persons Passenger Lift Car Size (2000 x 1500) Johnson /

Kone /

OTIS/

Equivalent

a Gearless Lift with Machine Room Each 2066000.00b Gearless Lift without Machine Room Each 2196000.00

Further increase of rate per floor for every additionalfloor Rs.1,00,000/- per floor. Comprehensive servicingand maintenance of lifts for further period of 2 yearsbeyond free warranty period of one year from thedate of commissioning of lifts will be paid at the rateof 5% of capital cost of lift

205


8 BED-CUM-PASSENGER LIFTS (G+3)SS 304

Grade with 1m/sec. speed with ARD

A 15 Persons Passenger Lift Car Size (1000 x 2400) Kone /

Equivalent

a Gearless Lift with Machine Room Each 1814000.00b Gearless Lift without Machine Room Each 1929000.00B 20 Persons Passenger Lift Car Size (1300 x 2400)

a Gearless Lift with Machine Room Each 2167000.00b Gearless Lift without Machine Room Each 2257000.00C 26 Persons Passenger Lift Car Size (1600 x 2400)

a Gearless Lift with Machine Room Each 2463000.00b Gearless Lift without Machine Room Each 2655000.00

Further increase of rate per floor for every additionalfloor Rs.1,00,000/- per floor. Comprehensive servicingand maintenance of lifts for further period of 2 yearsbeyond free warranty period of one year from thedate of commissioning of lifts will be paid at the rateof 5% of capital cost of lift

XV PART “O”

1 GI STEEL TUBULAR POLE FOR STREET LIGHT Kumaran Pole /

Orient Pole /

Equivalent

a 4 Metre Length Single Bracket Pole withBase Plate (250 x 250 x 6mm) Each 6350.0076.10mm OD x 3.65mm Thick x 4000mm Length

b 4 Metre Length Double Bracket Pole withBase Plate (250 x 250 x 6mm) Each 7230.0076.10mm OD x 3.65mm Thick x 4000mm Length

c 6 Metre Length Single Bracket Pole withBase Plate (250 x 250 x 6mm) Each 7590.0076.10mm OD x 3.65mm Thick x 6000mm Length

d 6 Metre Length Double Bracket Pole withBase Plate (250 x 250 x 6mm) Each 8470.0076.10mm OD x 3.65mm Thick x 6000mm Length

e 7 Metre Length Single Bracket Pole withBase Plate (250 x 250 x 6mm) Each 9730.00114.30mm OD x 5.40mm Thick x 4000mm Length,88.90mm OD x 4.85mm Thick x 1500mm Length,76.1mm OD x 3.25mm Thick x 1500mm Length

206


f 7 Metre Length Double Bracket Pole withBase Plate (250 x 250 x 6mm) Each 10700.00114.30mm OD x 5.40mm Thick x 4000mm Length,88.90mm OD x 4.85mm Thick x 1500mm Length,76.10mm OD x 3.25mm Thick x 1500mm Length

g 7.50 Metre Length Single Bracket Pole withBase Plate (250 x 250 x 6mm) Each 10870.00114.30mm OD x 5.40mm Thick x 4500mm Length,88.90mm OD x 4.85mm Thick x 1500mm Length,76.1mm OD x 3.25mm Thick x 1500mm Length

h 7.50 Metre Length Double Bracket Pole withBase Plate (250 x 250 x 6mm) Each 12010.00114.30mm OD x 5.40mm Thick x 4500mm Length,88.90mm OD x 4.85mm Thick x 1500mm Length,76.10mm OD x 3.25mm Thick x 1500mm Length

i 8 Metre Length Single Bracket Pole with Base Plate(250 x 250 x 6mm) Each 11190.00114.30mm OD x 5.40mm Thick x 4500mm Length,88.90mm OD x 4.85mm Thick x 1750mm Length,76.10mm OD x 3.25mm Thick x 1750mm Length

j 8 Metre Length Double Bracket Pole with Base Plate(250 x 250 x 6mm) Each 12320.00114.30mm OD x 5.40mm Thick x 4500mm Length,88.90mm OD x 4.85mm Thick x 1750mm Length,76.10mm OD x 3.25mm Thick x 1750mm Length

k 8.50 Metre Length Single Bracket Pole withBase Plate (250 x 250 x 6mm) Each 11930.00114.30mm OD x 5.40mm Thick x 5000mm Length,88.90mm OD x 4.85mm Thick x 1750mm Length,76.10mm OD x 3.25mm Thick x 1750mm Length

l 8.50 Metre Length Double Bracket Pole withBase Plate (250 x 250 x 6mm) Each 13390.00114.30mm OD x 5.40mm Thick x 5000mm Length,88.90mm OD x 4.85mm Thick x 1750mm Length,76.10mm OD x 3.25mm Thick x 1750mm Length

m 9 Metre Length Single Bracket Pole withBase Plate (300 x 300 x 6mm) Each 11930.00

207


114.30mm OD x 5.40mm Thick x 5000mm Length,88.90mm OD x 4.85mm Thick x 2000mm Length,76.10mm OD x 3.25mm Thick x 2000mm Length

n 9 Metre Length Double Bracket Pole with Base Plate(300 x 300 x 6mm) Each 13390.00114.30mm OD x 5.40mm Thick x 5000mm Length,88.90mm OD x 4.85mm Thick x 2000mm Length,76.10mm OD x 3.25mm Thick x 2000mm Length

o 10 Metre Length Single Bracket Pole with BasePlate (300 x 300 x 6mm) Each 15800.00139.70mm OD x 4.50mm Thick x 5200mm Length,114.30mm OD x 4.50mm Thick x 2400mm Length,88.90mm OD x 3.25mm Thick x 2400mm Length

p 10 Metre Length Double Bracket Pole with Base Plate(300 x 300 x 6mm) Each 16230.00139.70mm OD x 4.50mm Thick x 5200mm Length,114.30mm OD x 4.50mm Thick x 2400mm Length,88.90mm OD x 3.25mm Thick x 2400mm Length

q 12 Metre Length Single Bracket Pole with Base Plate(300 x 300 x 6mm) Each 18620.00165.10mm OD x 4.50mm Thick x 5800mm Length,139.70mm OD x 4.50mm Thick x 3100mm Length,114.30mm OD x 3.65mm Thick x 3100mm Length

r 10 Metre Length Double Bracket Pole with Base Plate(300 x 300 x 6mm) Each 20640.00165.10mm OD x 4.50mm Thick x 5800mm Length,139.70mm OD x 4.50mm Thick x 3100mm Length,114.30mm OD x 3.65mm Thick x 3100mm Length

2 Octogonal post Kumaran

Pole /

Equivalent

a Supply erection of 8mm free standing single arm bracket8 sided octogonally continously tapered structuredpole with base plate of size 300x300x12mm as per IS875 with following specifications.Bottom pole dia -130mmTop Pole Dia - 70mmThickness of pole -3mmThe pole should be hot tip galvanized confirmingto BESN ISO 1461 with thickness of 65 micron Each 20790.00

208


b Supply erection of 8mm free standing double armbracket 8 sided octogonally continously taperedstructured pole with base plate of size 300x300x12mmas per IS 875 with following specifications.Bottom poledia - 130mmTop Pole Dia - 70mmThickness of pole -3mmThe pole should be hot tip galvanized confirmingto BESN ISO 1461 with thickness of 65 micron Each 21920.00

c Supply erection of 7mm free standing double armbracket 8 sided octogonally continously taperedstructured pole with base plate of size 250x250x12mmas per IS 875 with following specifications.Bottom poledia - 140mmTop Pole Dia - 70mmThickness of pole -3mmThe pole should be hot tip galvanized confirmingto BESN ISO 1461 with thickness of 65 micron Each 20910.00

2 LIGHTNING ROD Jef Flash /

Nimbus /

Equivalent

a Supply of Early Streamer Emission Air Terminal(ESEAT). Model: L Each 73120.00The ESEAT has corrosion resistant stainless chromebody made up of AISI 316 grade of height 0.50 metrescapable of working in hazardous atmosphere. The Airterminal is non-radioactive and requires no speciallicensing. The unit is fully autonomous (no battery, noexternal power supply is required), collects energyfrom the ambient electric field.The ESEAT model hasbeen tested in a high voltage laboratory in accordancewith NFC 17 102 in order to measure the average gainin triggering. The average gain in triggering time (”Ts)obtained during the lab test for the offered model is60 μs. The ESEAT works on negative as well aspositively polarized discharges. ESEAT has been testedfor such discharges in Central Power Research Institute(CPRI). A dedicated tester is avilable to test thehealthiness of the ESEAT on request (Page No. 37,Point No. 3 of Clause 8.6 of the Revised NFC 17-102version 2011 ).ESEAT Model : L - Radius of protection : 86 MetresLevel of protection considered for the Project-II level

209


b Supply of Early Streamer Emission Air Terminal(ESEAT). Model: S Each 64940.00

The ESEAT has corrosion resistant stainless chrome

body made up of AISI 316 grade of height 0.50 metrescapable of working in hazardous atmosphere. The Air

terminal is non-radioactive and requires no special

licensing. The unit is fully autonomous (no battery, noexternal power supply is required ), collects energy

from the ambient electric field.The ESEAT model has

been tested in a high voltage laboratory in accordancewith NFC 17 102 in order to measure the average gain

in triggering. The average gain in triggering time (”Ts)

obtained during the lab test for the offered model is60 μs.

The ESEAT works on negative as well as positively

polarized discharges. ESEAT has been tested for suchdischarges in Central Power Research Institute (CPRI).

A dedicated tester is avilable to test the healthiness

of the ESEAT on request (Page No. 37, Point No. 3 ofClause 8.6 of the Revised NFC 17-102 version 2011 ).

ESEAT Model : S - Radius of protection : 46 Metres

Level of protection considered for the Project-II levelc MOUNTING STRUCTURE

Supply of Standard / Special Mounting Structure of

height4.5 mts. pipe, and 300 x 300 x 8mm MS plate, 3mts. 48mm OD class C GI outer pipe,1.8 mtr, 38mm

OD inner pipe, for roof mounting on concrete base

and with FRP adapter Each 19490.00d DOWN CONDUCTOR

Supply and run of 25mm x 6mm GI Flat Down Condutor

with necessary clamps / supports on wall / floor /ground for earth connection Mtr 113.00

e TEST LINK

Supply of Test Link Box for each Down conductor inorder to disconnect the earth termination system

to enable measurement of resistance Each 4796.00

210


f EARTH ELECTRODE

Supply and insallation maintenance free GI EarthingSystem comprising of 50mm dia and 2 mtr. long earthelectrode of low carbon steel rod with 100 micronbonding and 25 kgs. of carbon based environmentfriendly backfill compound and suitable clamp Each 8850.00

g SURDGE PROTECTION

Supply and insallation Cabinet Type Class 1 and 2Combined Model SPD to arrest surges and overvoltagesin the power line due to lighning switching action etc.they must be installed in the incoming MCC panel / DBof the respective buling in parallel to the power circuit. Each 18600.00Model: PSV4-12.5/400TT (3 phase power network)

XVI PART “P”

Conference type Public Address System, BOSCH/

Projector and Motorized Screen Equivalent

1 Chairman Unit Each 14946.002 Delegate Unit Each 13250.003 Conference Controller Set 33145.004 PA Mixer Amplifier 120W Set 19957.005 PA Mixer Amplifier 240W Set 25607.006 PA Booster Amplifier 480W Set 44220.007 Wall Speaker 15W Each 8594.008 Wall Speaker 30W Each 12493.009 Ceiling Speaker 15W Each 2175.0010 Ceiling Speaker 20W Each 3361.00

AKG/

Equivalent

11 Cordless Mic UHF Each 20000.00Orbit/

Equivalent

12 8 Pin Conference Mic socket with Modular Box andFront Plate Each 327.70

13 2 Core 1.5 sq.mm Shielded Copper Speaker Wire RM 40.5014 8 Core 1.5 sq.mm PVC Copper Conference Cable RM 155.50

Sony/

Equivalent

15 3200 Ansi Lumens Projector, XGA (1024 x 768)Resolution, Contrast Ratio : 4000:1 Each 38800.00

211


16 3600 Ansi Lumens Projector, XGA (1024 x 768)Resolution, Contrast Ratio : 20000:1 Each 55190.00

17 3300 Ansi Lumens Short Throw Projector,WXGA (1280 x 800) Resolution, Contrast Ratio:3000 : 1 Each 97240.00

Liberty/

Equivalent

18 6' x 4' Motorized Screen Each 11970.0019 8' x 6' Motorized Screen Each 16060.0020 10' x 8' Motorized Screen Each 19290.0021 3 Feet Ceiling Mount Kit Each 4252.0022 20 Metre HDMI Cable Set 4210.00

Orbit/

Equivalent

23 3 Core 1.5 sq.mm PVC Power cable for Projector RM 57.3024 Unarmoured 0.5mm Telephone cablea 2 Pair RM 9.05b 4 Pair RM 16.15c 10 Pair RM 38.30d 20 Pair RM 70.70e 50 Pair RM 159.5025 Armoured 0.5mm Jellyfilled Telephone Cablea 10 Pair RM 148.40b 20 Pair RM 218.10c 50 Pair RM 424.00d 100 Pair RM 735.20e 200 Pair RM 1369.0026 Unarmoured Co-axial Cable for TVa RG-06 RM 23.20b RG-11 RM 52.5027 Armoured Co-Axial cable for TVa RG-06 RM 88.80b RG-11 RM 126.2028 Unarmoured LAN & CCTV Cablea CAT-6 RM 29.2029 Armoured LAN & CCTV Cablea CAT-6 RM 104.0030 Unarmoured Speaker Cablea 2 Core - 1.00 sq.mm RM 28.20b 2 Core - 1.5 sq.mm RM 40.40

212


31 Armoured Speaker Cablea 2 Core - 1.5 sq.mm RM 83.80b 2 Core - 2.5 sq.mm RM 104.0032 OFC Cablea 6 Core indoor RM 53.50b 6 core outdoor RM 58.50c 12 core indoor RM 68.6033 PoE Switches for CCTV IP camera D-link/

Equivalent

a 4 Port Each 6098.00b 8 port Each 8430.00c 24 Port Each 19080.0034 Network Video Recorder for CCTVa 4 Channel - 1 SATA Each 5514.00b 8 Chennel - 1 SATA (1 No. Hard disk) Each 6363.00c 16 Chennel - 2 SATA (2 Nos. Hard disk) Each 11660.00d 32 Chennel - 2 SATA (2 Nos. Hard disk) Each 21200.0035 LAN NETWORK SWITCHESI Un Managed 10/ 100/1000a 8 Port Each 1962.00b 16 Port Each 5143.00c 24 Port Each 6310.00II Semi managed 10/100/1000a 24 Port Each 11870.00III Fully Managed 10/100/1000 Layer 2 with 1G Uplinka 8 Port Each 16960.00b 24 Port Each 34990.00c 24 Port with Fibre port Each 62560.00d 48 Port Each 42400.00IV Fully Managed 10/100/1000 Layer 2 with 10G Uplinka 24 Port Each 38170.00b 28 Port Each 49040.00V Fully Managed 10/100/1000 Layer 3 with 10G Uplinka 24 Port Each 111350.00b 24 Port with Fibre port Each 127200.00c 48 Port Each 206700.0036 Media Convertor for optical fibre cablea Single mode Each 5302.00b Multi mode Each 4772.00

213


37 I/O Socketa RJ-45 Each 159.50b RJ-11 Each 63.60c CAT 6 PVC Module Box Each 63.60d Face plate single socket RJ-45 Each 95.90e Face plate dual socket RJ-45 Each 106.00f Face plate quad socket RJ-45 Each 117.00

38 Hard Disk for NVR Western/

Digital/

Equivalent

a 2 TB Each 5832.00b 4 TB Each 12355.00c 6 TB Each 16755.00d 8 TB Each 24390.0039 Rack with Accessories D-link/

Equivalent

a 2U Rack Each 1908.00b 4U Rack Each 2650.00c 6U Rack Each 3180.00d 9U Rack Each 4240.00e 12U Rack Each 6360.00f 36U Rack Each 21200.00g 42U Rack Each 37100.00h Fan extra for the above rack Each 530.0040 Patch Corda 1 Metre Length Each 138.00b 2 Metre Length Each 185.00c 3 Metre Length Each 223.00d 24 Port Patch Panel - Unloaded Each 2120.00e 24 Port Patch Panel - Fully loaded Each 3977.00

XVII PART “Q”

HIRE CHARGES FOR TEMPROARY ARRANGEMENTS

1 Metal Hallide lampa 1 day Each 265.00b 2 days Each 334.00c 3 days Each 386.00d 4 days Each 435.00e 5 days Each 487.00f 6 days Each 530.00g 7 days Each 583.00

214


2 Generator Starting & Inter

End day mediate

(Each) days

(Each)

a 62.5 KVA Each 1,696.00 1357.00b 125 KVA Each 3,499.00 2799.00c 250 KVA Each 6,999.00 5599.00d 320 KVA Each 8,377.00 6702.00e 500 KVA Each 12,726.00 10180.003 Cable

a 2 of 7/20 sq.mm RM 2.02b 4 of 7/20 sq.mm RM 4.04c 4 of 19/16 sq.mm RM 11.10d 4 of 7/16 sq.mm RM 6.05e 4 of 120 sq.mm RM 53.50f 3.5x 180 sq.mm LTUG RM 21.20g 4 of 185 sq.mm RM 74.70h 3 core flexible wire RM 3.03i 4 core flexible wire RM 3.03j 4 core 6 sq.mm copper cables RM 6.05k 4 x 10 sq.mm flexible cable RM 6.05l 2 of 3/ 20 sq.mm RM 2.02m 3 1/2 x 50 sq.mm LTUG RM 11.10n Co- Axial cable RM 1.014 Serial set

a 2 days RM 17.15b 3 days RM 25.255 Fly Catcher 2 days Each 169.606 Air cooler with stand 2 days Each 286.007 Air Circulator 2 days Each 63.608 Pedestal fan Each 42.409 LED Nose Light Each 18.1510 Earth pipe Each 32.3011 100A Change over switch Each 159.5012 250A Change over switch Each 169.6013 400A Change over switch Each 212.0014 250A Change over switch with Panel Board Each 795.0015 100A Panel Board with 100A TPN Switch &

5 Nos 30A TPN switch with bus bar Each 822.00

215


16 250A Panel Board with 250A TPN Switch & 7 Nos63A DPMCB switch Each 1060.00

17 100A Panel Board incoming 100A TPN Switch withvarious range of TP/ DP/ SP MCB with suitable angleiron frame work Each 784.00

18 200A Panel Board Each 848.0019 400A Panel Board Each 1590.0020 4’40 W Patty tube light with fitting Each 25.2021 15A/ 5A Plug board Each 25.2022 Blank post Each 1962.0023 6mtr GI post for metal Hallide fitting Each 95.9024 1.5 TR Split AC Each 5302.0025 2 TR Split AC Each 7105.0026 5 TR Split AC Each 25025.0027 7.5 TR Ductable AC Each 36585.0028 5 TR Slim pack Each 24815.0029 Air Curtain Each 530.0030 High power Audio sysytem Each 47720.0031 PA sysytem Each 7423.0032 Amplifier, Mic, XLR Each 5302.0033 2x15 HF 3 way speaker Each 1696.0034 1x15 HF Speaker Each 1060.0035 4x12 Loud speaker Each 636.0036 Car calling system Arrangement Each 3181.0037 Cordless Mic Each 530.0038 Wired Mic Each 530.0039 32 Channel mixer Amplifier Each 636.0040 Laptop to play CD Songs Each 2120.0041 5KVA with 1 Hour back up Each 7953.0042 Power Amplifier Each 212.0043 Sony Video Camera Each 5302.0044 42" Plasma Screen Each 2651.0045 Mixer Board, Computer, UPS, etc., Each 8480.0046 200W LED Flood light fitting Each 212.0047 5TR Slim Package AC Each 26830.00

Note: The Basic Rate adopted under this Head, Rates ofElectrical Items of Works” is exclusive of all taxes andGST.

216

XVIII VERTICAL THREE PHASE DISTRIBUTION BOARD WITH MCBS

4 Way / 8 way / 12 Way Vertical TPMCB sheet steel distribution boards Flush type/Surface type fitted with Bus bars and Neutral links with single / three phase MCB outgoings and separate 4 way provision for accommodating one No.4 pole incoming MCB /Isolator and another separate 4 way provision for accommodating one No. 4 pole ELCB/RCD with label holder and provisions for taking up cable for size not less than 35 sq.mm

1. TPMCB DB WITH META DOOR COVER WITH IP 42 PROTECTION

Description No. of ways No.of ways No.of Legrand All otherHavell’s / incomer outgoing (MDS) / makes withincomer ELCB/RCD ways HAGER ISI (StdMCB/ ( L & T) /HPL /

Isolator equivalent)(Rate inRupees)

4 Ways 3 Phase DB 4 4 12 5351.00 4397.00

8 Ways 3 Phase DB 4 4 24 6783.00 5413.00

12 Ways 3 Phase DB 4 4 36 9044.00 6658.00

2.TPMCB DB WITH ACRYLIC DOOR COVER WITH IP 42 PROTECTION

No. of ways No.of ways No.of Legrand (MDS) /Description incomer incomer outgoing HAGER

MCB/ ELCB/RCD ways ( L & T) Rate in Rs.Isolator

4 Ways 3 Phase DB 4 4 12 6461.00

8 Ways 3 Phase DB 4 4 24 8225.00

12 Ways 3 Phase DB 4 4 36 10938.00

3. 6 WAY VERTICAL TPN DISTRUBUTION BOARD

6 Way Vertical TPN Distributions boards;IP43 with double door (Metal); with 12 Each 9919.00module incomers and 18 Single Phase/Three Phase/ MCB’s outgoing; as perIS 8623 III

217

4.INDUSTRIAL TYPE TPMCB DB WITH IP 54 PROTECTION

Description No. of ways No.of ways No.of Legrand (MDS) /incomer incomer outgoing HAGERMCB/ ELCB/RCD ways ( L & T) Rate in Rs.

Isolator4 Ways 3 Phase DB 4 4 12 9999.00

8 Ways 3 Phase DB 4 4 24 12069.0012 Ways 3 Phase DB 4 4 36 16180.00

XIX HORIZONTAL THREE PHASE DISTRIBUTION BOARD WITH MCBS

4 way / 6 way / 8 way / 12 way TPMCB sheet steel distribution boards Flush type /Surface type fitted with Bus bars and Neutral links with single/ three phase MCB outgoingsand separate 4 way provision for accommodating one No. 4 pole incoming MCB / Isolatorand another separate 4 way provision for accommodating one No. 4 pole ELCB / RCD withlabel holder and provisions for taking up cable for size not less than 35 sq.mm

1. TPMCB DB WITH METAL DOOR COVER WITH IP 42 PROTECTION


Isolator equivalent)(Rate inRupees)

4 Ways 3 Phase DB 4 4 12 2240.00 1773.00

6 Ways 3 Phase DB 4 4 18 2758.00 2240.00

8 Ways 3 Phase DB 4 4 24 3308.00 2748.00

12 Ways 3 Phase DB 4 4 36 4885.00 3733.00

2.TPMCB DB WITH ACRYLIC DOOR COVER WITH IP 42 PROTECTION



4 Ways 3 Phase DB 4 4 12 2602.00

6 Ways 3 Phase DB 4 4 18 3194.00

8 Ways 3 Phase DB 4 4 24 3816.00

12 Ways 3 Phase DB 4 4 36 5817.00

218

3.INDUSTRIAL TYPE TPMCB DB WITH IP 54 PROTECTION



4 Ways 3 Phase DB 4 4 12 6316.00

6 Ways 3 Phase DB 4 4 18 7602.00

8 Ways 3 Phase DB 4 4 24 8318.00

12 Ways 3 Phase DB 4 4 36 11483.00

XX 7 SEGMENTS (3 TIER) 3 PHASE DISTRIBUTION BOARD WITH MCB

4 Way/6 way/8 way/12 Way TPMCB sheet steel distribution boards Flush type/Surface typefitted with Bus bars and Neutral links with single /three phase MCB out goings and separate4 way provision for accommodating one No. 4 pole incoming MCB /Isolator and anotherseparate 4 way provision for accommodating one No. 4 pole ELCB/RCD (Totally 8 ways inone segment)(3 x 4 ways in each segment) and separate provision for MCB /Isolator)(Totally12 Nos. ) for sub incomers in 3 segments with label holder and provisions for taking upcable for size not less than 35 sq.mm

1. Vertical TPN Distribution Boards (with Unit Hager / Hager /MCCB Incomer); Double Door; IP43, Equivalent Equivalentas per IS 8623 III; Impact resistance IK09; (Incomer (IncomerFrame MCCB Incomer & Single Phase/Three Phase 160A 250AMCBs as Outgoing (for power loads exceeding 100A) MCCB) MCCB)

4 Way, MCCB + 12 Modules Each 8958.00 16590.00





2.TPMCB DB WITH METAL /ACRYLIC DOOR COVER WITH IP 42 PROTECTION

Description No. of ways No. of ways No.of Sub No. of out Legrand (MDS)incomer incomer incomers going ways /HAGER(L&T)

MCB/Isolator ELCB/RCD Rate in Rupees

4 Ways 3 Phase DB 4 4 12 12 5258.00

6 Ways 3 Phase DB 4 4 12 18 5942.00

8 Ways 3 Phase DB 4 4 12 24 6627.00

12 Ways 3 Phase DB 4 4 12 36 8442.00

219

XXI SINGLE PHASE DISTRIBUTION BOARD WITH MCBs

4 way/8 way/12 way Vertical SPMCB sheet steel distribution boards Flush type/Surfacetype fitted with Bus bars and Neutral links with single phase MCB out goings and separate 2way provision for accommodating one No. 2 pole incoming MCB /Isolator and another separate2 way provision for accommodating one No, 2 pole ELCB/RCD with label holder and provisionsfor taking up cable for size not less than 35 sq.mm

1. SPMCB DB WITH METAL DOOR COVER WITH IP 42 PROTECTION


Isolator equivalent equivalent)(Rate inRupees)

4 Ways single Phase DB 2 2 2 881.00 576.00



2. SPMCB DB WITH ACRYLIC DOOR COVER WITH IP 42 PROTECTION

Description No. of ways No.of ways No.of Legrand (MDS) /incomer incomer outgoing HAGERMCB/ ELCB/RCD ways ( L & T) / equivalent

Isolator Rate in Rs.

4 Ways single Phase DB 2 2 2 1039.00



3.INDUSTRIAL TYPE SPMCB DB WITH IP 54 PROTECTION.

Description No. of ways No.of ways No.of Legrand (MDS) /incomer incomer outgoing HAGERMCB/ ELCB/RCD ways ( L & T) equivalent

Isolator Rate in Rs.




220

.

221

III (H) RATES FOR CONVEYANCE OFMATERIALS

222

.

223

CONVEYANCE1) Rates for Conveyance of C.I/G.I/D.I. Pipes and Specials

Up to 125 mm 315.53 207.31 207.31 167.00 897.16Over 125 mm up to200 mm 432.28 277.21 277.21 178.38 1165.07Over 200 mm up to350 mm 530.45 366.72 366.72 181.61 1445.50Over 350 mm up to500 mm 663.54 434.31 434.31 204.30 1736.47Over 500 mm up to700 mm 801.09 502.04 502.04 225.31 2030.48Above 700mm 901.50 598.05 598.05 243.21 2340.80

Unloadingfrom

Railwaywagons or

loadinginto

Railwaywagons/

Tonne2

Rs. P.

Loadinginto cartsor lorries/

Tonne

3

Rs. P.

Unloadingfrom cartsor lorries &stacking/

Tonne

4

Rs. P.

Transportcharges upto 8km or

partthereof/

Tonne

5

Rs. P.

Total/Tonne

6

Rs. P.

Size

1

For every 1 KM or part thereof Rate per Tonne in Rupees

up to 500 mm Above 500 mm

Beyond 8 KM to 25 KM 12.91 14.54

Above 25 KM to 50 KM 9.38 11.03

Above 50 KM to 80 KM 8.22 9.80

Above 80 KM to 125 KM 6.16 8.15

Above 125 KM to 200 KM 6.16 6.16

Above 200 KM 4.04 4.04

Note: 1) For lorry and cart consignments of capacity one Tonne and below, double therates may be allowed, when the total quantity to be transported is within 1.00M.T.

2) For Lorry consignments from 1 to 2 Tonnes, the rates admissible for two Tonnesmay be allowed, when the total quantity to be transported is within 2 M.T.

3) For Lorry Consignments from 2 to 5 Tonnes, the rates admissible for 5 Tonnesmay be allowed, when the total quantity to be transported is within 5 M.T.

4) Above 5 Tonnes of Lorry consignment, full lorry load rate of 9 Tonnes may beallowed.

5) For the conveyance of E.R.W.M.S. seamless pipes and specials up to 350mm dia,the rates of C.I. Pipes of respective dia available in the Schedule of rates may beadopted.

6) An extra rate of Rs. 32.90 per Tonne may be allowed for unloading from Railwaywagons and stacking before loading into carts and lorries.

224

2) Rates for Conveyance of M.S. Pipes and Specials



Beyond 8 KM to 25 KM 29.15 32.38

Above 25 KM to 50 KM 20.88 25.11Above 50 KM to 80 KM 18.01 22.59Above 80 KM to 125 KM 14.20 18.07Above 125 KM to 200 KM 14.20 14.20Above 200 KM 10.03 10.03

Note : 1) For lorry and cart consignments of capacity one Tonne and below double the ratesmay be allowed, when the total quantity to be transported is within 1.00 M.T.

2) For Lorry consignments from 1 to 2 Tonnes the rates admissible for two Tonnes maybe allowed, when the total quantity to be transported is within 2 M.T.

3) For Lorry Consignments from 2 to 5 Tonnes the rates admissible for 5 Tonnes maybe allowed, when the total quantity to be transported is within 5 M.T.


5) An extra rate of Rs. 32.90 per Tonne may be allowed for unloading from Railwaywagons and stacking before loading into carts and lorries.

Up to 350 mm 1191.84 825.12 825.12 415.13 3257.20

Over 350 mm up to

500 mm 1497.45 977.96 977.96 460.53 3913.89Over 500 mm up to

700 mm 1807.40 1121.94 1121.94 509.16 4560.44

Above 700mm 2030.08 1353.40 1353.40 551.27 5288.16

Unloadingfrom

Railwaywagons or

loadinginto

Railwaywagons/

Tonne2

Rs. P.


Tonne

3

Rs. P.


Tonne

4

Rs. P.


partthereof/

Tonne

5

Rs. P.

Total/Tonne

6

Rs. P.

Size

1

225

3) Rates for Conveyance of R.C.C. /P.S.C/B.W.S.C. Pipes and Specials

Unloadingfrom

Railwaywagons or

loadinginto

Railwaywagons/

Tonne2

Rs. P.


Tonne

3

Rs. P.


Tonne

4

Rs. P.


partthereof/

Tonne

5

Rs. P.

Total/Tonne

6

Rs. P.

Size

1

For every 1 KM or part thereofRate per Tonne in Rupees


Beyond 8 KM to 25 KM 11.08 14.84

Above 25 KM to 50 KM 7.45 11.27

Above 50 KM to 80 KM 6.22 10.21

Above 80 KM to 125 KM 6.22 8.15

Above 125 KM to 200 KM 6.22 6.22

Above 200 KM 4.11 4.11

150 mm to 200 mm 244.45 187.69 187.69 191.29 811.11

Over 200 mm up to

350 mm 303.32 240.13 240.13 201.03 984.60

Over 350 mm up to

500 mm 379.77 296.82 296.82 209.18 1182.60

Over 500 mm up to

700 mm 473.62 349.26 349.26 236.69 1408.84

Above 700mm 515.17 388.50 388.50 256.22 1548.39

Note : 1) For lorry and cart consignments of capacity 1 Tonne and below, double the ratesmay be allowed, when the total quantity to be transported is within 1 M.T.

2) For Lorry consignments up to 5 MT (i.e.) above 1 MT Load, the rates admissiblefor 5 Tonnes may be allowed.

226

4) Rates for Conveyance of A.C. Pipes and Specials

Up to 125 mm 161.50 143.98 143.98 291.83 741.30

Over 125 mm

up to 200 mm 220.38 152.77 152.77 306.43 832.36

Over 200 mm

up to 250 mm 251.03 187.69 187.69 348.61 975.01

For 300 mm 270.64 196.41 196.41 358.34 1021.81

For 350 mm 270.64 218.27 218.27 363.22 1070.40

For 400 mm 281.54 242.29 242.29 387.56 1153.66

For 450 mm 312.06 270.64 270.64 410.26 1263.60

For 500 mm 331.81 298.99 298.99 423.16 1352.95

For 600 mm 364.49 342.69 342.69 454.02 1503.89

For 700 mm 379.77 351.43 351.43 455.66 1538.30

Unloadingfrom

Railwaywagons or

loadinginto

Railwaywagons/

Tonne2

Rs. P.


Tonne

3

Rs. P.


Tonne

4

Rs. P.


partthereof/

Tonne

5

Rs. P.

Total/Tonne

6

Rs. P.

Size

1



Beyond 8 KM to 25 KM 22.28 26.05

Above 25 KM to 50 KM 13.14 15.07Above 50 KM to 80 KM 12.26 14.32Above 80 KM to 125 KM 10.15 12.26Above 125 KM to 200 KM 8.15 10.15Above 200 KM 6.22 8.15

Note : 1) For lorry and cart consignments of capacity one Tonne and below double therates may be allowed, when the total quantity to be transported is within 1 M.T.

2) For Lorry consignments from 1 to 2 Tonnes the rates admissible for two Tonnesmay be allowed, when the total quantity to be transported is within 2 M.T.

3) For Lorry Consignments from 2 to 5 Tonnes the rates admissible for 5 Tonnes maybe allowed, when the total quantity to be transported is within 5 M.T.


5) For the conveyance of E.R.W.M.S. seamless pipes and specials up to 350mm dia,the rates of C.I. Pipes of respective dia available in the Schedule of Rates maybe adopted.

6) An extra rate of Rs. 32.86/Tonne may be allowed for unloading from Railwaywagons and stacking before loading into carts and lorries.

227

5) Rates for Conveyance of PVC/ HDPE /GRP Pipes and Specials


Beyond 8 KM to 25 KM 42.00

Above 25 KM to 50 KM 28.04



Above 125 KM to 200 KM 14.25

Above 200 KM 10.15

Note: 1) For departmentally loading of PVC pipes and Rs. 3.10 each length (6m)Specials (excluding transport charges)Up to 110 mm dia

2) For departmentally unloading of PVC pipes and Rs. 3.10 each length (6m)Specials Up to 110 mm dia

3) a. For departmentally loading for Rs. 175.20 per 1 MTremaining sizes of pipes

b. For departmentally unloading for Rs. 175.20 per 1 MTremaining sizes of pipes

4) An extra rate of Rs. 34.65 / Tonne may be allowed for unloading from Railwaywagons and stacking before loading into carts and lorries.

5) For lorry and cart consignments of capacity one Tonne and below double therates may be allowed, when the total quantity to be transported is within 1 M.T.

6) For Lorry consignments from 1 to 2 Tonnes the rates admissible for two Tonnesmay be allowed, when the total quantity to be transported is within 2 M.T.

7) For Lorry Consignments from 2 to 5 Tonnes the rates admissible for 5 Tonnesmay be allowed, when the total quantity to be transported is within 5 M.T.

50mm to 110mm OD 209.48 183.36 183.36 486.52 1062.72

125mm to200mm OD 270.64 185.45 185.45 489.69 1131.23

Over 200mm to

315mm OD 275.04 244.45 244.45 526.99 1290.94

Over 315mm OD 279.37 250.95 250.95 572.40 1353.67

Unloadingfrom

Railwaywagons or

loadinginto

Railwaywagons/

Tonne2

Rs. P.


Tonne

3

Rs. P.


Tonne

4

Rs. P.


partthereof/

Tonne

5

Rs. P.

Total/Tonne

6

Rs. P.

Size

1

228

6) Rates for Conveyance of SW Pipes and Specials

100 to 200 mm 303.33 198.58 198.58 265.90 966.40

Over 200 to 350 mm 384.18 255.35 255.35 286.96 1181.84

Over 350 mm to

500 mm 482.35 307.72 307.72 311.30 1409.09







Above 200 KM 4.11

Note: 1) For lorry and cart consignments of capacity one Tonne and below doublethe rates may be allowed, when the total quantity to be transported is within1 M.T.

2) An extra rate of Rs.34.65 / Tonne may be allowed for unloading from Railwaywagons and stacking before loading into carts and lorries.

Unloadingfrom

Railwaywagons or

loadinginto

Railwaywagons/

Tonne2

Rs. P.


Tonne

3

Rs. P.


Tonne

4

Rs. P.


partthereof/

Tonne

5

Rs. P.

Total/Tonne

6

Rs. P.

Size

1

229

7) Rates for Conveyance of Pig lead and Yarn

Pig lead / Yarn 104.67 89.45 89.45 97.25 380.82







Above 200 KM 4.11

Unloadingfrom

Railwaywagons or

loadinginto

Railwaywagons/

Tonne2

Rs. P.


Tonne

3

Rs. P.


Tonne

4

Rs. P.


partthereof/

Tonne

5

Rs. P.

Total/Tonne

6

Rs. P.

Size

1

Note: The above rates are basic rates only and GST extra applicable as per GO.

230

8 a) Rates for Conveyance of Materials by Road in Hills

Rate for 2020-21 in RupeesSl.N

o.

Dis

tanc

e in

Kilo

met

re

Cem

ent

and

Ste

el(O

ne m

etri

c to

nne)

Lim

esto

ne, L

ater

ite,

Bri

ckje

lly,

Woo

d w

ork,

Pon

d A

sh (

wet

/dr

y),

ston

e du

st(O

ne C

ubic

Met

re)

Rou

gh S

tone

, B

ond

Sto

ne,

Cut

Sto

ne, B

roke

n S

tone

jelly

, S

and,

Gra

vel,

Sur

ki, E

arth

, Cru

shed

ston

e sa

nd(O

ne C

ubic

Met

re)

Thir

d C

lass

Cou

ntry

Bri

cks

(Kiln

Bur

nt)

(100

0 no

s.)

Bri

cks

II

clas

s C

ham

ber

burn

tBri

cks

(Tab

le M

ould

ed/G

roun

dM

ould

ed),

Fly

Ash

Bri

cks

(100

0 N

os.)

1 2 3 4 5 6 7 8

1 Co-efficient 1.00 1.10 1.60 1.35 1.80 2.25

2 Add for every extra 1 Km and part thereof……………

a 0 to 10 kms 13.02 14.28 20.8 17.56 23.40 29.24

b 10 to 20 kms 11.14 12.24 17.8 15.02 20.04 25.04

c 20 to 40 kms 9.58 10.54 15.34 12.90 17.24 21.54

d 40 to 80 kms 8.26 9.10 14.38 11.14 14.84 18.60

e Above 80 kms 7.54 8.30 12.06 10.18 13.56 16.96M

anga

lore

Tile

s (1

000

Nos

.)M

achi

ne P

ress

ed T

iles

(200

0 N

os.)

Hyd

raul

ical

ly p

ress

ed M

osai

cFl

oorin

g T

iles

(150

0 N

os.)

Note: 1. The above rates do not include stacking charges [as per Circular Memo No.230Wks.IV(2)/62-3 dated 10.06.1962 of Chief Engineer (General/ PWD)]

2. For Conveyance of Materials on cart track, allow 20% extra over the aboverates excluding loading and unloading charges.

3. For Sandy and Slushy soil tracks, add 50% extra over the above rates excludingloading and unloading charges.

4. The quantity for Payment towards conveyance of earth in coloumn (5) is for thepit measured quantity at the site of excavation only.

5. For conveyance of laterite, broken stone jelly, etc., through lorries, the ratesprovided are for the volume with voids.

6. For all materails which finds place in column 3,4,5,6,7 & 8 above, necessaryincidental charges, loading charges and unloading charges have been includedalready under their basic cost furnished below the head “Rates of Materials”itself. Hence, no separate incidental charges, loading and unloading chargesshall be allowed for the above materials.

7. The above rates are basic rates only and GST extra applicable as per GO

231

8 b) Rates for Conveyance of Materials by Road in plains


1 2 3 4 5 6 7 8

1 Co efficient 1.00 1.10 1.60 1.35 1.80 2.25

2 Add for every extra 1Km and part there of

a 0 to 10 kms 6.51 7.14 10.40 8.78 11.70 14.62

b 10 to 20 kms 5.57 6.12 8.90 7.51 10.02 12.52

c 20 to 40 kms 4.79 5.27 7.67 6.45 8.62 10.77

d 40 to 80 kms 4.13 4.55 7.19 5.57 7.42 9.30

e Above 80kms 3.77 4.15 6.03 5.09 6.78 8.48

3 Loading Charges 116.30 55.50 38.00 54.60 54.60 54.60

4 Unloading Charges 116.30 55.50 38.00 54.60 54.60 54.60

5 Add above extra for

inter state works 23.40 25.70 37.60 31.60 42.20 53.00

Note: 1 The above rates do not include stacking charges [as per Circular Memo No.230Wks.IV(2)/62-3 dated 10.06.1962 of Chief Engineer (General)]

2 For Conveyance of Materials on cart track, allow 20% extra over the above ratesexcluding loading and unloading charges.

3 For Sandy and Slushy soil tracks, add 50% extra over the above rates excludingloading and unloading charges.

4 The quantity for Payment towards conveyance of earth in coloumn (5) is for thepit measured quantity at the site of excavation only.

5 For conveyance of laterite, broken stone jelly, etc., through lorries, the ratesprovided are for the volume with voids.

6 For all materails which finds place in column 3,4,5,6,7 & 8 above, necessaryincidental charges, loading charges and unloading charges have been includedalready under their basic cost furnished below the head “Rates of Materials”itself. Hence, no separate incidental charges, loading and unloading charges shallbe allowed for the above materials.

7 The above rates are basic rates only and GST extra applicable as per GO

Sl.N

o.

Dis

tanc

e in

Kilo

met

re

Cem

ent

and

Ste

el(O

ne m

etri

c to

nne)

Lim

esto

ne, L

ater

ite,

Bri

ckje

lly,

Woo

d w

ork,

Pon

d A

sh (

wet

/dr

y),

ston

e du

st(O

ne C

ubic

Met

re)

Rou

gh S

tone

, B

ond

Sto

ne,

Cut

Sto

ne, B

roke

n S

tone

jelly

, S

and,

Gra

vel,

Sur

ki, E

arth

, Cru

shed

ston

e sa

nd(O

ne C

ubic

Met

re)

Thir

d C

lass

Cou

ntry

Bri

cks

(Kiln

Bur

nt)

(100

0 no

s.)

Bri

cks

II

clas

s C

ham

ber

burn

tBri

cks

(Tab

le M

ould

ed/G

roun

dM

ould

ed),

Fly

Ash

Bri

cks

(100

0 N

os.)

Man

galo

re T

iles

(100

0 N

os.)

Mac

hine

Pre

ssed

Tile

s (2

000

Nos

.)H

ydra

ulic

ally

pre

ssed

Mos

aic

Floo

ring

Tile

s (1

500

Nos

.)

232

9) Rates for Conveyance of materials by Head load

Rate for 2020-21 in RupeesLEAD LIFT

Above Add extra Add extra10m and for every for every

Sl.No Description of material Unit upto additional 1m height100m 100m or or part

part thereofthereof for more

than2m lift

1 2 3 4 5 6

1 Rough Stone, Broken Stone Jelly,Cut Stone, RCC Slab, Sand - cu.m 101.20 42.00 10.95Cement Block, Wooden Scantling,Wooden plank

2 Lime, Lime Stone, Laterite,Brick Jelly, Earth, Sand,Gravel, cu.m 53.80 42.00 8.20Surki, Pond Ash (wet/dry),Crushed Stone Sand, Stone Dust

3 a) Mangalore Tiles 1000 Nos. 109.70 55.10 13.85b) Machine Pressed Tiles 2000 Nos. 109.70 55.10 13.85c) Hydraulic Pressed Mosaic

Flooring Tiles 1500 Nos. 109.70 55.10 13.85

d) Terrace Bricks, Flat Tilesand Pan Tiles 2500 Nos. 109.70 55.10 13.85

e) Bricks 1000 Nos. 109.70 55.10 13.854 Cement, A.C. Sheet, Bitumen,

Asphalt, Tar M.T 99.90 55.10 10.95

5 Steel M.T 167.90 67.50 10.95

Note: 1 Fraction of 100 metres to be rounded off to the nearest 100 metres

2 The rates indicated in the table shall be applicable only to inaccessible places(i.e) the places Wherever the Bullock Carts cannot move [Chief Engineer(General) Memo No.CTO(A) / 38153 / 89 / dated 03.02.1989]

3 For an initial lead of 10m and initial lift of 2m, no charge towards head load isallowable.

4 The above rates are basic rates only and GST extra applicable as per GO

233

IV (A) RATES FOR WORKS

234

.

235

INFILTRATION WORKS

Schedule Rate for

Item No. Description Unit 2020 - 21in Rupees

1 Earthwork excavation above water levelin light or sandy or clayey soils formanhole wells, infiltration wells, suctionwells etc. including levelling the site withan initial lead of 10 metres

First depth of 2 metres One Cubic metre 76.49

Second depth of 2 metres One Cubic metre 121.48Third depth of 2 metres One Cubic metre 175.47

Fourth depth of 2 metres One Cubic metre 244.462 Erection of Ring well below water level

including all incidental charges usingspecial tools and plants such as aircompressor helmet etc. complete andincluding bailing out water.

a. For 0.90 metre dia Ring well (internal)

First depth of 2 metres One metre 620.91

Second depth of 2 metres One metre 1144.34Third depth of 2 metres One metre 2405.65

Fourth depth of 2 metres One metre 4803.81

Fifth depth of 2 metres One metre 9459.14Sixth depth of 2 metres One metre 18933.27

b. For 1.2 metre dia Ring well (internal)

First depth of 2 metres One metre 689.90Second depth of 2 metres One metre 1379.80

Third depth of 2 metres One metre 2750.60

Fourth depth of 2 metres One metre 5153.26Fifth depth of 2 metres One metre 9564.12

Sixth depth of 2 metres One metre 19107.25

c. For 1.50 metre dia Ring well (internal)First depth of 2 metres One metre 797.89

Second depth of 2 metres One metre 1583.77

Third depth of 2 metres One metre 3134.55Fourth depth of 2 metres One metre 6243.60

Fifth depth of 2 metres One metre 12469.20

Sixth depth of 2 metres One metre 24831.92

236

3 Sinking well below water levelincluding all incidental chargesusing special tools and plantssuch as air compressor, helmetetc., complete and includingbaling out water

a. For 1.0 metre dia (internal)

First depth of 2 metres One metre 907.37 1309.31

Second depth of 2 metres One metre 1526.78 2398.15

Third depth of 2 metres One metre 3052.06 4791.81

Fourth depth of 2 metres One metre 6024.63 9568.62

Fifth depth of 2 metres One metre 11468.85 17968.91

Sixth depth of 2 metres One metre 21533.90 33631.16

Seventh depth of 2 metres One metre 31595.95 45716.42

Eighth depth of 2 metres One metre 41662.50 57800.18

Nineth depth of 2 metres One metre 51720.05 69879.44

Tenth depth of 2 metres One metre 61785.10 81964.70

b. For 1.25 metre dia (internal)











c. For 2.0 metre dia (internal)




Schedule Description Unit


Item No.Ordinary

Silt (or) claysoil (or)pocketloose soil

sandy soil

237








d. For 2.5 metre dia (internal)











e. For 3.00 metre dia (internal)













Item No.Ordinary


sandy soil

238

f. For 3.50 metre dia (internal)











g. For 4.00 metre dia (internal)











h. For 4.50 metre dia (internal)











Item No.Ordinary


sandy soil

239



i. For 5.00 metre dia (internal)











j. For 6.00 metre dia (internal)











NOTE: In case the water table is met with at depth of 2.00 m and below, fromthe bed level, an extra percentage as under may be allowed over theexisting rates for items 3(a) to 3 (j) for the extra lift involved.

Where water table is 2.00m, below bed leveland upto 4.00 m 15% extra

Where water table is beyond 4.00mand upto 6.00m 20% extra



Item No.Ordinary


sandy soil

240

Schedule Rate for


4a. Earthwork excavation above water levelin light or sandy soil for infiltration gallery,syphon or connecting pipeline andconnected works including refillingcomplete.First depth of 2 m One cubic metre 88.49Second depth of 2 m One cubic metre 125.98Third depth of 2 m One cubic metre 184.47Fourth depth of 2 m One cubic metre 247.46

b. Earthwork excavation below water level inlight or sandy soil for infiltration gallery,syphon or connecting pipe line andconnected works including shoring andstrutting and charges for special tools andplants for bailing/ pumping etc., such asair compressor and helmet.First depth of 2 m One cubic metre 1654.26Second depth of 2 m One cubic metre 2338.16Third depth of 2 m One cubic metre 3507.99Fourth depth of 2 m One cubic metre 5090.27

c Earthwork excavation below water level inclayey soil for infiltration gallery for layingsyphon pipe line or connecting pipe andconnected works, shoring and strutting andcharges for special tools and plants forbailing/pumping etc., such as aircompressor and helmet.First depth of 2 m One cubic metre 2750.60Second depth of 2 m One cubic metre 3822.95Third depth of 2 m One cubic metre 5972.14Fourth depth of 2 m One cubic metre 8937.21

d Earthwork excavation below water level insoft disintegrated rock for infiltrationgallery, laying syphone pipe line/ connectingpipes etc., including shoring, strutting andcharges for special tools and plants.First depth of 2 m One cubic metre 1922.72Second depth of 2 m One cubic metre 2563.13Third depth of 2 m One cubic metre 3992.43Fourth depth of 2 m One cubic metre 6902.01

241

Schedule Rate for


NOTE (i) For sinking wells in soil mixed with pebblesboulder of size 80 mm to 600 mm mixedwith clay and silt below water level,including bailing/ pumping water andcharges for special tools and plants etc.,complete, an extra 20% (Twentypercentage) over the rates for items2,3b,3c & 3d in the schedule of rates isallowed.

ii In case the water table is met with at adepth of 2.00m and below from the bedlevel, an extra percentage as under maybe allowed over the existing rates for items4(b), 4(c) and 4(d) above the extra liftinvolvedWhere water table is 2.00m below bedlevel and upto 4.00m. 10% extraWhere water table is beyond 4.00m andupto 6.00m 15% extra

Pipe laying works5a Laying stoneware pipes and open joint with

fillet in the infliltration gallery excluding costof pipes but including charges of specialtools and plant etc., such as aircompressor and helmet.

I 200 mm dia stoneware pipes One metre 263.96ii 225 mm dia stoneware pipes One metre 323.95iii 300 mm dia stoneware pipes One metre 379.45iv 350 mm dia stoneware pipes One metre 439.44v 375 mm dia stoneware pipes One metre 545.92vi 450 mm dia stoneware pipes One metre 562.42b Laying and jointing PVC slotted pipes in

the inflitration gallery excluding cost ofpipes but including charges for special toolsand plants etc., complete such as aircompressor and helmet.200 mm dia (OD) PVC pipes One metre 194.97315 mm dia (OD) PVC pipes One metre 299.96

c Refilling gallery trench and filter basins withclean excavated sand free from silt and clay One cubic metre 20.85

242

6 Labour charges for laying filter media belowwater level in all depths as per specificationfor infiltration gallery works includingscreening cleaning and charges for specialtools and plant etc.,complete such as aircompressor, helmets, sheet piles

a Granite metal 6mm to 40mm One cubic metre 272.96b Coarse sand passing through a sieve of

four meshes to 2.5 centimetres and retainedin a sieve of ten meshes to 2.5 centimetresand filling it under water One cubic metre 1355.80

c Coarse sand passing through a sieve often meshes to 2.5 centimetres andretained in a sieve of 200 meshes to 2.5centimetres and filling it under water One cubic metre 514.43

d. Cost of coarse sand D-10 and D-20 forlaying gallery media for a lead not exceeding200m from the source to the place ofstacking including stacking etc., complete. One cubic metre 349.45

e. Cost of hard granite metal of size (B.S.S.)6 mm to 12 mm filter media (machinecrushed) One cubic metre 1841.73(i) NOTE: For 6(a),(b) and (c):The above rates are labour charges forlaying the filter media including screening,cleaning etc., for a lead not exceeding 200metres from the place of stacking to thepoint of laying the media. The cost ofmaterials and the lead from the source tothe place of stacking are to be paid forseparately.(ii) NOTE: FOR 6(d):The above rates are applicable to caseswhere the screened materials is not lessthan 10% of the collected material. Inspecific cases where the screened materialis less than 10% of the collected material,prior orders of the Superintending Engineer,TWAD Board are to be obtained in specificcases for increased rate of labour required.

Schedule Rate for


243

(iii) NOTE: FOR 6(e)The above rates are applicable to caseswhere the screened materials is not lessthan 20% of the collected materials. Incase where the screened materials is lessthan 20% of the collected material, priororders of the Superintending Engineer,TWAD are to be obtained in specific casesfor increased rate of labour required.

7a Lowering of C.I Pipes and specials in thetrenches and laying to proper grade andalignment and as directed by the TWADOfficers.For depth upto 2m80 mm dia C.I Pipes and Specials One metre 12.29100 mm dia C.I Pipes and Specials One metre 13.81125 mm dia C.I Pipes and Specials One metre 18.15150 mm dia C.I Pipes and Specials One metre 24.95200 mm dia C.I Pipes and Specials One metre 30.14250 mm dia C.I Pipes and Specials One metre 35.42300 mm dia C.I Pipes and Specials One metre 38.46350 mm dia C.I pipes and specials One metre 48.90400 mm dia C.I pipes and specials One metre 57.14450 mm dia C.I pipes and specials One metre 66.13500 mm dia C.I pipes and specials One metre 72.21600 mm dia C.I pipes and specials One metre 88.27700 mm dia C.I pipes and specials One metre 113.59750 mm dia C.I pipes and specials One metre 128.21800 mm dia C.I pipes and specials One metre 146.49900 mm dia C.I pipes and specials One metre 172.91NOTE: i) For depth between 2m to 4m 10%over basic rates and for 4m to 6m 20%over basic rate allowedii) For work of laying CI connecting pipe/syphon basic pipe below water, double theabove rates shall be allowed.iii) For laying pipes in sewer line exceptpumping main 10% more is allowed.

Schedule Rate for


244

7a(i) Lowering of D.I Pipes and specials in thetrenches and laying to proper grade andalignment and as directed by the TWADOfficers.For depth upto 2m80 mm dia D.I Pipes and Specials One metre 12.84100 mm dia D.I Pipes and Specials One metre 14.45125 mm dia D.I Pipes and Specials One metre 18.39150 mm dia D.I Pipes and Specials One metre 24.95200 mm dia D.I Pipes and Specials One metre 30.73250 mm dia D.I Pipes and Specials One metre 36.31300 mm dia D.I Pipes and Specials One metre 40.46350 mm dia D.I pipes and specials One metre 50.41400 mm dia D.I pipes and specials One metre 57.14450 mm dia D.I pipes and specials One metre 68.55500 mm dia D.I pipes and specials One metre 72.81600 mm dia D.I pipes and specials One metre 89.55700 mm dia D.I pipes and specials One metre 111.29750 mm dia D.I pipes and specials One metre 124.13800 mm dia D.I pipes and specials One metre 147.85900 mm dia D.I pipes and specials One metre 174.42NOTE: i) For depth between 2m to 4m10% over basic rates and for 4m to 6m20% over basic rate allowedii) For work of laying DI connecting pipe/syphon basic pipe below water, double theabove rates shall be allowed.iii) For laying pipes in sewer line exceptpumping main 10% more is allowed.

b Lowering GI pipes and specials in thetrenches and laying to proper grade andalignment, Jointing with GI Specials andas directed by the TWAD Officers15mm to 40mm dia One metre 15.5350mm to 65mm dia One metre 15.5380mm to 100mm dia One metre 20.89125mm to 150mm dia One metre 20.89

c Disjointing C.I. Tyton S/S pipes andspecials, and lifting C.I. Pipes from thetrenches and stacking at places shown bythe departmental Officers.

Schedule Rate for


245

For depth upto 2 m80 mm dia C.I. Pipes and specials One metre 14.25100mm dia C.I. Pipes and specials One metre 16.65125 mm dia C.I. Pipes and specials One metre 19.20150 mm dia C.I. Pipes and specials One metre 26.40200 mm dia C.I. Pipes and specials One metre 28.80250 mm dia C.I. Pipes and specials One metre 45.44300 mm dia C.I. Pipes and specials One metre 48.29350 mm dia C.I. Pipes and specials One metre 62.69400 mm dia C.I. Pipes and specials One metre 67.34450 mm dia C.I. Pipes and specials One metre 79.34500 mm dia C.I.pipes and specials One metre 86.69600 mm dia C.I.pipes and specials One metre 105.88700 mm dia C.I.pipes and specials One metre 122.68800 mm dia C.I.pipes and specials One metre 134.83825 mm dia C.I.pipes and specials One metre 154.18900 mm dia C.I.pipes and specials One metre 170.83

% excessNOTE: For depth between allowed over

basic rate2m to 4m 10%4m to 6m 20%

d. Lowering of M.S pipes and specials intothe trenches and laying to proper gradeand alignment and as directed by theTWAD Officers.Up to 350mm dia One metre 39.11400 mm Dia One metre 47.44450 mm Dia One metre 52.33500 mm Dia One metre 54.55600 mm Dia One metre 68.18700 mm Dia One metre 89.92900 mm Dia One metre 128.321000 mm Dia One metre 165.051050 mm Dia One metre 173.081100 mm Dia One metre 179.331200 mm Dia One metre 184.691400 mm Dia One metre 281.201600 mm Dia One metre 379.00

PercentageNOTE: For depth between excess allowed

over basic rate2m to 4m 10%4m to 6m 20%

Schedule Rate for


246

Schedule Rate for


8a Jointing the C.I/ D.I - S/S pipes andspecials with molten lead and Yarn includingcaulking the joints. (Including cost ofjointing materials)For depth upto 2m80 mm dia C.I/ D.I - S/S pipes and specials Each Joint 482.62100 mm dia C.I/ D.I - S/S pipes and specials Each Joint 604.78125 mm dia C.I/ D.I - S/S pipes and specials Each Joint 784.01150 mm dia C.I/ D.I - S/S pipes and specials Each Joint 907.40200 mm dia C.I/ D.I - S/S pipes and specials Each Joint 1252.61250 mm dia C.I/ D.I - S/S pipes and specials Each Joint 1701.31300 mm dia C.I/ D.I - S/S pipes and specials Each Joint 1932.80350 mm dia C.I/ D.I - S/S pipes and specials Each Joint 2405.71400 mm dia C.I/ D.I - S/S pipes and specials Each Joint 2825.68450 mm dia C.I/ D.I - S/S pipes and specials Each Joint 3608.30500 mm dia C.I/ D.I - S/S pipes and specials Each Joint 3914.24600 mm dia C.I/ D.I - S/S pipes and specials Each Joint 4965.15700 mm dia C.I/ D.I - S/S pipes and specials Each Joint 5402.14750 mm dia C.I/ D.I - S/S pipes and specials Each Joint 6747.08

PercentageNOTE: For depth between excess

allowed over basic rate

2m to 4m 10%4m to 6m 15%

8b Jointing C.I/ D.I-S/S pipes and specialswith rubber gaskets (tyton joint) includingcost of lubricants. (including cost of jointingmaterials)For depth upto 2m80 mm dia C.I/ D.I-S/S pipes and specials Each Joint 41.62100 mm dia C.I/ D.I-S/S pipes and specials Each Joint 55.37125 mm dia C.I/ D.I-S/S pipes and specials Each Joint 56.37150 mm dia C.I/ D.I-S/S pipes and specials Each Joint 59.37200 mm dia C.I/ D.I-S/S pipes and specials Each Joint 68.24250 mm dia C.I/ D.I-S/S pipes and specials Each Joint 98.03300 mm dia C.I/ D.I-S/S pipes and specials Each Joint 110.60350 mm dia C.I/ D.I-S/S pipes and specials Each Joint 123.60400 mm dia C.I/ D.I-S/S pipes and specials Each Joint 142.60450 mm dia C.I/ D.I-S/S pipes and specials Each Joint 214.80500 mm dia C.I/ D.I-S/S pipes and specials Each Joint 233.80600 mm dia C.I/ D.I-S/S pipes and specials Each Joint 314.65

247

Schedule Rate for


700 mm dia C.I/ D.I-S/S pipes and specials Each Joint 373.73750 mm dia C.I/ D.I-S/S pipes and specials Each Joint 480.10800 mm dia C.I/ D.I-S/S pipes and specials Each Joint 597.14900 mm dia C.I/ D.I-S/S pipes and specials Each Joint 902.60



8c Jointing the C.I/ D.I Double flanged pipesand specials with rubber insertion with IS638 (1979) and M.S. bolts and nuts of IS13641 (2002) including cost of Jointingmaterials such as bolt and nuts Rubberinsertion and labour charges etc.For depth upto 2mFor works above water level80 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 144.05100 mm dia C.I./D.I. Double flanged pipesand specials Each Joint 246.41125 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 256.19150 mm dia C.I./D.I. Double flanged pipesand specials Each Joint 411.76200 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 462.71250 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 653.64300 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 734.59350 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 947.82400 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 1426.36450 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 1632.92500 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 1996.52600 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 2804.30700 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 2860.16

248

Schedule Rate for


750 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 2941.55800 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 2953.42900 mm dia C.I/ D.I Double flanged pipesand specials Each Joint 3482.57

PercentageNOTE: For depthbetween excess allowed


8d Jointing C.I/ D.I double flanged pipes andspecials with rubber insertion or anyequivalent to the required specificationswith M.S. bolts and nuts etc., completeincluding charges for special tools andplants such as air compressor and helmetsand sheet piles. etc (including cost ofjointing materials)For depth upto 2mFor works below water level80 mm dia C.I/ D.I Double flanged Pipesand specials Each Joint 325.15100 mm dia C.I/ D.I Double flanged Pipesand specials Each Joint 484.28125 mm dia C.I/ D.I Double flanged Pipesand specials Each Joint 539.92150 mm dia C.I/ D.I Double flanged Pipesand specials Each Joint 771.19200 mm dia C.I/ D.I Double flanged Pipesand specials Each Joint 889.22250 mm dia C.I/ D.I Double flanged Pipesand specials Each Joint 1214.68300 mm dia C.I/ D.I Double flanged Pipesand specials Each Joint 1340.06350 mm dia C.I/ D.I Double flanged Pipesand specials Each Joint 1660.56400 mm dia C.I/ D.I Double flanged Pipesand specials Each Joint 2282.37450 mm dia C.I/ D.I Double flanged Pipesand specials Each Joint 2540.33500 mm dia C.I/ D.I Double flanged Pipesand specials Each Joint 2983.82

249

Schedule Rate for


600 mm dia C.I/ D.I Double flanged Pipesand specials Each Joint 4201.04



8e Jointing the C.I/ D.I-S/S pipes and specialswith neat cement or cement mortar andspun yarn including caulking the joints,curing. (including cost of jointing materials)For depth upto 2m80mm dia C.I/ D.I-S/S Pipes and Specials Each Joint 125.23100mm dia C.I/ D.I-S/S Pipes and Specials Each Joint 129.36125mm dia C.I/ D.I-S/S Pipes and Specials Each Joint 168.06150mm dia C.I/ D.I-S/S Pipes and Specials Each Joint 193.72200mm dia C.I/ D.I-S/S Pipes and Specials Each Joint 305.13250mm dia C.I/ D.I-S/S Pipes and Specials Each Joint 359.66300mm dia C.I/ D.I-S/S Pipes and Specials Each Joint 422.48350mm dia C.I/ D.I-S/S Pipes and Specials Each Joint 514.81400mm dia C.I/ D.I-S/S Pipes and Specials Each Joint 589.47450mm dia C.I/ D.I-S/S Pipes and Specials Each Joint 725.21500mm dia C.I/ D.I-S/S Pipes and Specials Each Joint 815.00600mm dia C.I/ D.I-S/S Pipes and Specials Each Joint 1010.05700mm dia C.I/ D.I-S/S Pipes and Specials Each Joint 1110.60



9 Lowering RCC pipes and specials into thetrenches and laying to proper grade andalignmentFor depth upto 2m150mm dia R.C.C. Pipes and Specials One metre 43.19200mm dia R.C.C. Pipes and Specials One metre 45.44250mm dia R.C.C. Pipes and Specials One metre 57.74300mm dia R.C.C. Pipes and Specials One metre 67.34350mm dia R.C.C. Pipes and Specials One metre 84.14400mm dia R.C.C. Pipes and Specials One metre 91.34

250

Schedule Rate for


450mm dia R.C.C. Pipes and Specials One metre 105.88500mm dia R.C.C. Pipes and Specials One metre 122.68600mm dia R.C.C. Pipes and Specials One metre 142.03700mm dia R.C.C. Pipes and Specials One metre 158.98750mm dia R.C.C. Pipes and Specials One metre 166.03800mm dia R.C.C. Pipes and Specials One metre 202.32900mm dia R.C.C. Pipes and Specials One metre 238.321000mm dia R.C.C. Pipes and Specials One metre 274.611100mm dia R.C.C. Pipes and Specials One metre 320.351200mm dia R.C.C. Pipes and Specials One metre 356.651300mm dia R.C.C. Pipes and Specials One metre 392.64



i) Each Collar joint is to be treated as onejoint only

ii) For laying RCC pipes in sewage lines, exceptpumping main, 5% more is allowed

10a Jointing RCC pipes with cement usingnecessary collars including the cost ofjointing materials.For depth upto 2m150mm dia R.C.C. Pipes and Specials Each Joint 233.52200mm dia R.C.C. Pipes and Specials Each Joint 286.46250mm dia R.C.C. Pipes and Specials Each Joint 351.70300mm dia R.C.C. Pipes and Specials Each Joint 395.19350mm dia R.C.C. Pipes and Specials Each Joint 424.14400mm dia R.C.C. Pipes and Specials Each Joint 457.73450mm dia R.C.C. Pipes and Specials Each Joint 537.22500mm dia R.C.C. Pipes and Specials Each Joint 592.86600mm dia R.C.C. Pipes and Specials Each Joint 706.10700mm dia R.C.C. Pipes and Specials Each Joint 821.73750mm dia R.C.C. Pipes and Specials Each Joint 867.78800mm dia R.C.C. Pipes and Specials Each Joint 901.37900mm dia R.C.C. Pipes and Specials Each Joint 1024.051000mm dia R.C.C. Pipes and Specials Each Joint 1048.351100mm dia R.C.C. Pipes and Specials Each Joint 1147.181200mm dia R.C.C. Pipes and Specials Each Joint 1272.57

251

Schedule Rate for


1300mm dia R.C.C. Pipes and Specials Each Joint 1407.55% excess allowed

NOTE: For depth between over basic rate2m to 4m 10%4m to 6m 15%Each collar joint is to be treated as onejoint only.

10b Jointing RCC pipes with lead and hemp yarnusing steel collars including the cost ofjointing materials and caulking the joints.For depth upto 2m150mm dia R.C.C. Pipes Each steel collar 248.06200mm dia R.C.C. Pipes Each steel collar 310.76250mm dia R.C.C. Pipes Each steel collar 368.50300mm dia R.C.C. Pipes Each steel collar 426.39350mm dia R.C.C. Pipes Each steel collar 484.28400mm dia R.C.C. Pipes Each steel collar 503.63450mm dia R.C.C. Pipes Each steel collar 631.26500mm dia R.C.C. Pipes Each steel collar 706.10600mm dia R.C.C. Pipes Each steel collar 843.48700mm dia R.C.C. Pipes Each steel collar 1007.40800mm dia R.C.C. Pipes Each steel collar 1159.33



11a Lowering AC/ GRP pipes and specials intothe trench carefully, laying to proper gradeand alignment, jointing of A.C/ GRP pipeswith simplex joints with rubber rings or withC.I. detachable joints or with M.S. couplers.For depth upto 2m80mm dia AC/ GRP Pipes One metre 21.45100mm dia AC/ GRP Pipes One metre 28.80125mm dia AC/ GRP Pipes One metre 43.19150mm dia AC/ GRP Pipes One metre 48.14200mm dia AC/ GRP Pipes One metre 64.79250mm dia AC/ GRP Pipes One metre 79.34300mm dia AC/ GRP Pipes One metre 101.09350mm dia AC/ GRP Pipes One metre 112.93400mm dia AC/ GRP Pipes One metre 130.03

252

Schedule Rate for


450mm dia AC/ GRP Pipes One metre 151.78500mm dia AC/ GRP Pipes One metre 180.57600mm dia AC/ GRP Pipes One metre 216.87700mm dia AC/ GRP Pipes One metre 267.41



11b (i) Lowering PVC rigid pipes and specials totrench and laying to proper grade andalignment, jointing with PVC couplers withcement paste.For depth upto 2mUpto 40mm dia (OD) PVC pipe One metre 9.1250mm to 75mm dia (OD) PVC pipe One metre 15.4390mm to 110mm dia (OD) PVC pipe One metre 15.58125mm to 160mm dia (OD) PVC pipe One metre 21.97180mm to 250mm dia (OD) PVC pipe One metre 28.57Over 250mm to 315mm dia (OD) PVC pipe One metre 40.92



11b (ii) Lowering HDPE pipes and specials to trenchand laying to proper grade and alignmentand as directed by the TWAD OfficersFor depth upto 2m50mm to 75mm dia (OD) HDPE pipe One metre 14.2590mm to 110mm dia (OD) HDPE pipe One metre 14.25125mm to 160mm dia (OD) HDPE pipe One metre 20.10180mm to 250mm dia (OD) HDPE pipe One metre 25.80Over 250mm to 315mm dia (OD) HDPE pipe One metre 37.49



11c Lowering PSC/ BWSC pipes and specialsinto the trench and laying to proper gradeand alignment and Jointing with rubbergasketsFor depth upto 2mUpto 350mm diameter One metre 112.93

253

Schedule Rate for


400mm diameter One metre 132.28450mm diameter One metre 154.03500mm diameter One metre 180.57600mm diameter One metre 218.97700mm diameter One metre 245.81800mm diameter One metre 267.41900mm diameter One metre 291.411000mm diameter One metre 317.951100mm diameter One metre 342.251200mm diameter One metre 395.191300mm diameter One metre 438.541400mm diameter One metre 503.631500mm diameter One metre 558.97



11d Lowering CI collars with flange into thetrench and laying to proper grade andalignment and jointing PSC pipes with 2Nos of conical rubber rings and MS boltsand nuts excluding the cost of jointingmaterials.For depth upto 2mUpto 350mm diameter Each collar 1202.68400mm diameter Each collar 1407.55450mm diameter Each collar 1612.42500mm diameter Each collar 1814.74600mm diameter Each collar 2212.63700mm diameter Each collar 2815.24800mm diameter Each collar 3024.76900mm diameter Each collar 3427.461000mm diameter Each collar 4025.421100mm diameter Each collar 4432.461200mm diameter Each collar 5037.621300mm diameter Each collar 5649.84



254

Schedule Rate for


11e Testing of pipes for water supply withhydraulic testing equipment by filling withwater (including cost of water) @ Rs. 60/KL) and testing to recommended pressurein convenient stretches and attending thebursts if any occured during the test,excluding the cost of pipes but includingother incidential and operational chargesetc., complete for the following diametresof pipes.Up to 100mm One metre 61.64125mm One metre 72.59150mm One metre 81.59200mm One metre 99.74250mm One metre 125.08300mm One metre 152.38350mm One metre 179.52400mm One metre 208.62450mm One metre 239.52500mm One metre 292.16600mm One metre 348.40700mm One metre 442.74750mm One metre 517.13900mm One metre 596.911050mm One metre 769.391200mm One metre 967.21

12a Cutting C.I. Pipes true to axis and filingsmoothly and finishing the ends complete80mm dia CI pipes Each cutting 43.19100mm dia CI pipes Each cutting 48.14125mm dia CI pipes Each cutting 59.99150mm dia CI pipes Each cutting 67.34175mm dia CI pipes Each cutting 79.34200mm dia CI pipes Each cutting 108.13250mm dia CI pipes Each cutting 137.23300mm dia CI pipes Each cutting 154.03350mm dia CI pipes Each cutting 195.12375mm dia CI pipes Each cutting 241.02400mm dia CI pipes Each cutting 252.86450mm dia CI pipes Each cutting 271.91500mm dia CI pipes Each cutting 301.01525mm dia CI pipes Each cutting 363.70

255

Schedule Rate for


600mm dia CI pipes Each cutting 371.20675mm dia CI pipes Each cutting 443.34700mm dia CI pipes Each cutting 467.48750mm dia CI pipes Each cutting 482.03800mm dia CI pipes Each cutting 506.03825mm dia CI pipes Each cutting 551.77850mm dia CI pipes Each cutting 578.32900mm dia CI pipes Each cutting 592.86

12b Cutting A.C. Pipes true to axis andfinishing the ends complete80mm dia AC pipes Each cutting 16.65100mm dia AC pipes Each cutting 19.20125mm dia AC pipes Each cutting 21.45150mm dia AC pipes Each cutting 26.40200mm dia AC pipes Each cutting 35.84250mm dia AC pipes Each cutting 57.74300mm dia AC pipes Each cutting 59.99350mm dia AC pipes Each cutting 72.14400mm dia AC pipes Each cutting 88.79450mm dia AC pipes Each cutting 101.09500mm dia AC pipes Each cutting 115.63600mm dia AC pipes Each cutting 132.28700mm dia AC pipes Each cutting 146.83

12c Cutting P.V.C. rigid pipes and specials trueto axis and finishing the ends completeUpto 75mm dia (OD) PVC pipe Each cutting 5.5590mm dia PVC pipes Each cutting 8.40110mm dia PVC pipes Each cutting 8.40125mm dia PVC pipes Each cutting 8.40140mm dia PVC pipes Each cutting 8.40160mm dia PVC pipes Each cutting 14.25180mm dia PVC pipes Each cutting 17.10200mm dia PVC pipes Each cutting 17.10250mm dia PVC pipes Each cutting 20.10315mm dia PVC pipes Each cutting 22.80

12d. Cutting and Threading of GI pipesa.i 15mm dia GI pipe, Cutting Each 7.10ii. 15mm dia GI pipe, Threading Each 10.00b.i 20mm dia GI pipe, Cutting Each 7.10ii. 20mm dia GI pipe, Threading Each 10.20c.i 25mm dia GI pipe, Cutting Each 8.50ii. 25mm dia GI pipe, Threading Each 21.10

256

Schedule Rate for


d.i 32mm dia GI pipe, Cutting Each 10.20ii 32mm dia GI pipe, Threading Each 28.50

e.i 40mm dia GI pipe, Cutting Each 13.80ii 40mm dia GI pipe, Threading Each 32.00f.i 50mm dia GI pipe, Cutting Each 17.70ii. 50mm dia GI pipe, Threading Each 35.60g.i 65mm dia GI pipe, Cutting Each 19.20ii 65mm dia GI pipe, Threading Each 43.00

h.i 80mm dia GI pipe, Cutting Each 25.00ii. 80mm dia GI pipe, Threading Each 54.10i.i 100mm dia GI pipe, Cutting Each 35.60ii. 100mm dia GI pipe, Threading Each 71.70j.i. 125mm dia GI pipe, Cutting Each 37.96j.ii. 125mm dia GI pipe, Threading Each 76.1513 Cutting R.C.C. Pipes true to axis and

finishing the ends complete150mm dia R.C.C. Pipes Each cutting 60.00200mm dia R.C.C. Pipes Each cutting 67.34250mm dia R.C.C. Pipes Each cutting 86.69300mm dia R.C.C. Pipes Each cutting 112.93350mm dia R.C.C. Pipes Each cutting 117.88400mm dia R.C.C. Pipes Each cutting 151.48450mm dia R.C.C. Pipes Each cutting 166.03500mm dia R.C.C. Pipes Each cutting 185.37600mm dia R.C.C. Pipes Each cutting 207.12650mm dia R.C.C. Pipes Each cutting 216.87700mm dia R.C.C. Pipes Each cutting 238.32750mm dia R.C.C. Pipes Each cutting 245.81800mm dia R.C.C. Pipes Each cutting 269.81900mm dia R.C.C. Pipes Each cutting 286.461000mm dia R.C.C. Pipes Each cutting 308.511100mm dia R.C.C. Pipes Each cutting 329.951200mm dia R.C.C. Pipes Each cutting 354.101300mm dia R.C.C. Pipes Each cutting 368.50

14a Removing the burst C.I. pipes from thepipe line and removal of slushy soil andbaling out water and replacing the pipelinewith sound pipe including jointing andcost of refilling the pipeline with waterfor retesting the pipe line etc complete.(excluding cost of sound pipe and jointingmaterials and earth work) and as directedby the TWAD Board Officers.

257

Schedule Rate for


For depth upto 2m80mm dia C.I. Pipes Each 1116.00100mm dia C.I. Pipes Each 1400.20125mm dia C.I. Pipes Each 1829.14150mm dia C.I. Pipes Each 2306.52200mm dia C.I. Pipes Each 3217.64250mm dia C.I. Pipes Each 4423.01300mm dia C.I. Pipes Each 5628.09350mm dia C.I. Pipes Each 6373.03400mm dia C.I. Pipes Each 8142.18450mm dia C.I. Pipes Each 8870.17500mm dia C.I. Pipes Each 9952.42600mm dia C.I. Pipes Each 12177.35700mm dia C.I. Pipes Each 13293.19750mm dia C.I. Pipes Each 15255.35800mm dia C.I. Pipes Each 17229.52825mm dia C.I. Pipes Each 20432.91900mm dia C.I. Pipes Each 24928.51



14b Removing the burst A.C. Pipes from thepipe line and removal of slushy soil andbaling out water and replacing the pipeline with sound pipe including jointing andcost of refilling the pipe line with water forretesting the pipe line etc complete(excluding cost of sound pipe and jointingmaterials and earth work) and as directedby the TWAD Board OfficersFor depth upto 2m80mm dia AC. Pipes Each 645.81100mm dia AC. Pipes Each 763.84125mm dia AC. Pipes Each 961.36150mm dia AC. Pipes Each 1231.47200mm dia AC. Pipes Each 1728.05250mm dia AC. Pipes Each 2210.08300mm dia AC. Pipes Each 2752.55350mm dia AC. Pipes Each 3022.66375mm dia AC. Pipes Each 3400.76

258

Schedule Rate for


400mm dia AC. Pipes Each 3600.98450mm dia AC. Pipes Each 3678.07500mm dia AC. Pipes Each 4039.67600mm dia AC. Pipes Each 4702.42700mm dia AC. Pipes Each 5792.02



14c Removing the burst P.V.C. Pipes from thepipe line and removal of slushy soil andbaling out water and replacing the pipeline with sound pipe including jointing andcost of refilling the pipe line with waterfor retesting the pipe line etc., complete(excluding cost of sound pipe and jointingmaterials and earth work) and as directedby the TWAD Board OfficersUpto 63mm dia (OD) PVC Pipes Each 329.9575mm dia (OD) PVC Pipes Each 414.3990mm dia (OD) PVC Pipes Each 551.77110mm dia (OD) PVC Pipes Each 669.95125mm dia (OD) PVC Pipes Each 795.34140mm dia to 160mm dia (OD) PVC Pipes Each 981.01180mm dia to 200mm dia (OD) PVC Pipes Each 1503.08250mm dia to 280mm dia (OD) PVC Pipes Each 1831.84315mm dia (OD) PVC Pipes Each 2041.36



14d Removing the burst R.C.C. pipes from thepipe line and removal of slushy soil andbaling out water and replacing the pipeline with sound pipe including jointing andcost of refilling the pipe line with water forretesting the pipe line etc., complete.(excluding cost of sound pipe and jointingmaterials and earth work) and as directedby the TWAD Board Officers

259

Schedule Rate for


For depth upto 2m150mm dia RCC Pipes Each 1793.29200mm dia RCC Pipes Each 2521.14250mm dia RCC Pipes Each 3133.50300mm dia RCC Pipes Each 3721.41350mm dia RCC Pipes Each 4406.07375mm dia RCC Pipes Each 5235.30400mm dia RCC Pipes Each 5637.69450mm dia RCC Pipes Each 6302.99500mm dia RCC Pipes Each 7014.19525mm dia RCC Pipes Each 7983.20600mm dia RCC Pipes Each 8200.07650mm dia RCC Pipes Each 9149.88700mm dia RCC Pipes Each 9333.01800mm dia RCC Pipes Each 10299.62900mm dia RCC Pipes Each 11377.061000mm dia RCC Pipes Each 12437.711100mm dia RCC Pipes Each 13551.301200mm dia RCC Pipes Each 14626.341300mm dia RCC Pipes Each 15344.74NOTE: For depth between Percentage

excess allowedover basic rate

2m to 4m 15%4m to 6m 30%For sewerline works (Except pumping main)5% extra over the above rate may be adopted.

14e Charges for fixing MS Stepped split up collarin position in the spigot and socket endsof the PSC pipe carefully and caulking thesides of the collar using hemp yarn cementand hard concrete and pouring the cementslurry mixed with use of hard concrete inthe stepped collar including cost ofmaterials etc. complete but excluding costof stepped collar as directed by the TWADBoard OfficersUpto 1500mm dia PSC pipes Each 11798.80Upto 1000mm dia PSC pipes Each 9431.69Upto 800mm dia PSC pipes Each 5500.46Upto 700mm dia PSC pipes Each 5430.27Upto 600mm dia PSC pipes Each 5365.48Upto 500mm dia PSC pipes Each 5199.00

260

Schedule Rate for


Note: For lighting arrangements during nightworks due to emergency actualexpenditure incurred based on need forlighting may be given extra as certified bythe Executive Engineer incharge of workat site

14f Charges for lowering, positioning and fixingMS steps collars in AC pipe line carefullyand caulking the sides of collar using hempyarn, cement and hard concrete into thestepped collar including cost of jointingmaterials such as cement, yarn, bolt andnuts, MS washers, RI sheet and hardconcrete etc. but excluding cost of stepcollar and as directed by TWAD OfficersFor 500mm dia AC pipe Each 3931.08For 600mm dia AC pipe Each 4321.48For 700mm dia AC pipe Each 4914.64

i) For removing the burst pipe in themaintenance works when burst occurs andreplacing it with sound pipes including thecost of refilling the trench and the removalof slushy soil etc., Complete (Pipes andspecial jointing materials will be suppliedwith in 200m lead and at the respectiveTWAD Board divisional stores free of cost).2 times ordinary rate allowed for the worksare done during day time since the worksare done in confined reaches.

ii) If the works are done in odd hours (i.e)8.00 P.M. to 8.00 A.M. of the next day, 3times of ordinary rate is allowed since theworks are done in the confined reaches.Slow Sand / Rapid Sand Filter Works

15 a.i) Labour for filling with broken stone of allsizes well washed and cleaned, to be freefrom impurities, including stacking andlaying in bed One cubic metre 127.48

ii) Labour for filling the coarse sand passingthrough a sieve of 10 meshes to 2.5 cmand retained in 20 meshes to 2.5 cm wellwashed and cleaned to be free fromimpurities including stacking One cubic metre 241.02

261

Schedule Rate for


iii) Labour for filling with fine sand passingthrough a sieve of ten meshes to 2.5cmand retained in a sieve of 40 meshes to2.5 cm well washed and cleaned to befree from impurities including stacking One cubic metre 21.00

15 b Labour for scraping and removing silt onlyfrom the surface and sides of the filterbasin carrying the same to a distance notexceeding 200 metres One cubic metre 23.70

15c Labour for removing dirty sand in layer of25 mm uniform thickness from the slowsand filter, conveying, dropping the sandin a hopper with a lift of not exceeding 3metres within a distance of 30 metres anddelivering the washed sand in filter bedincluding removal and carrying the dirtfrom collecting chamber to a distance ofupto 200 metres. One square metre 28.65DRAINAGE WORKS

16 Laying and jointing with cement mortarstoneware pipes and specials in drycondition and testing with water100mm diameter stoneware pipes One metre150mm diameter stoneware pipes One metre200mm diameter stoneware pipes One metre225mm diameter stoneware pipes One metre250mm diameter stoneware pipes One metre300mm diameter stoneware pipes One metre375mm diameter stoneware pipes One metre450mm diameter stoneware pipes One metreNOTE : The rates to be worked out videstandard data appended as Item 17

17 Jointing HDPE Pipes and Specials by buttfusion welding/ electro fusion welding jointsusing fusion equipment as per ISO 21307-2011 and as per IS 7634 (Part-2) : 2012including cost of hire charges for butt fusionequipment power supply arrangementsetc., complete as per directed by TWADBoard officers.

1 50mm Joint 76.432 63mm Joint 95.18

262

Schedule Rate for


3 75mm Joint 113.934 90mm Joint 138.445 110mm Joint 167.286 125mm Joint 190.367 140mm Joint 213.438 160mm Joint 242.279 180mm Joint 279.7710 200mm Joint 310.0511 225mm Joint 350.4312 250mm Joint 389.3713 280mm Joint 434.0714 315mm Joint 488.8715 355mm Joint 550.8816 400mm Joint 621.5517 450mm Joint 697.9818 500mm Joint 775.8519 560mm Joint 896.9920 630mm Joint 1025.3318 Jointing of mechanical joint collar, nuts,

gasket and fixing in position as directedby departmental officers.

1 100mm Joint 96.622 150mm Joint 235.063 200mm Joint 242.274 250mm Joint 357.645 400mm Joint 752.786 450mm Joint 830.657 600mm Joint 1522.8619 Disjointing if GI pipes as directed by the

departmental officers1 upto 80mm Each 63.452 Above 80mm Each 83.6420 Welding of GI pipes as directed by the

departmental officers for the sizes1 upto 80mm One welding Joint 204.782 Above 80mm One welding Joint 235.06

Note: The Basic Rate adopted under this Head“ Rates of Works” is exclusive of all taxesand GST

263

DA

TA I

LLU

STR

ATI

ON

(R

ATE

S FO

R I

TEM

No.

16)

ITEM

No.

17.

LAYIN

G A

ND

JO

INTI

NG

STO

NE

WA

RE

PIP

ES F

OR

ON

E R

UN

NIN

G M

ETR

E(O

nly

for i

llust

rati

on p

urpo

se a

ssum

ing

Conv

eyan

ce c

harg

es fo

r 20K

M fo

r Cem

ent &

San

d an

d 8K

M fo

r Sto

new

are

pipe

s)

Length of each pipe in cm

Weight of S.W pipes for 30m(As per Hand Book of PHE)

Quantity of cement in Kgfor 50 joints

Labo

ur f

or L

ayin

gan

d jo

inting

Total cost of material and costof Labour for 30 mts. (Total No.

of Column 10 & 15) ( Rs. P )

Conveyance of pipes fromstock yard to site of work

Cost of Labour for a length of30m of SW pipes (Total No. ofcolumn 11,12,13 & 14) (Rs. P.)

Amount

Nos.

Amount

Amount

Amount

Total cost of materials(Total of columns 5,7,& 9)

Nos.

Nos.

Nos.

Mason IClass

(769.00)

FitterII Class(647.00)

MazdoorCategory I(502.00)

MazdoorCategory II

(412.00)

Cost of cement required for 50joints (Rs.)

(5800-20+118.4=5898)Quantity of sand in cubic metres

for 50 mortar joints

Cost of sand required for 50mortar joints at Rs. Per cum

(447+276.4=723)Quantity of spun of tarred yarn in Kg

Cost of yarn at Rs. 12.28 Kg

12

34

56

78

910

11

12

13

14

15

16

17

18

19

20

100

6043

545

265.

410.

0428

.92

3.63

44.5

833

8.91

215

381

647

525

102

824

5519

5857

.91

264.

9528

8.09

6410

.95

213.

70

150

6075

068

401.

060.

0750

.61

5.45

66.9

351

8.60

323

072

1294

630

123

1236

7849

8367

.60

456.

8239

0.26

9214

.68

307.

16

200

6010

4398

578.

000.

0857

.84

6.90

84.7

372

0.57

430

762

1294

630

123

1236

8618

9338

.57

635.

2839

3.61

1036

7.46

345.

58

225

6011

8510

461

3.19

0.10

72.3

8.17

100.

3378

6.02

538

453

1941

735

145

2060

1136

012

146.

0286

4.33

455.

5813

465.

9344

8.86

250

6013

7511

567

8.27

0.11

79.5

38.

3510

2.54

860.

345

3845

319

417

3514

520

6011

360

1222

0.34

1002

.91

470.

6613

693.

9145

6.46

300

6021

8015

088

4.70

0.15

108.

4511

.34

139.

2611

32.4

16

4614

319

4112

6024

624

7215

051

1618

3.41

1590

.07

599.

6318

373.

1161

2.44

375

6024

2531

818

75.5

60.

2820

2.44

18.1

422

2.76

2300

.76

753

833

1941

1470

287

2884

1723

619

536.

7620

50.4

867

3.32

2226

0.57

742.

02

Not

e :

1.

For

othe

r di

amet

er o

f pi

pes

now

man

ufac

ture

d, t

he r

ates

will

be

fixed

in d

ue c

ours

e af

ter

obse

rvin

g da

ta.

2.

The

rate

s ar

rived

at

adop

ting

the

data

app

ende

d to

thi

s sc

hedu

le o

f Ra

tes

is f

or w

orks

don

e in

the

firs

t 2.

00m

dep

th e

xtra

per

cent

age

5% f

or 2

m t

o 2.

5m,

7.50

%fo

r 2.

50m

to

3m,

10%

for

3m

to

3.50

m 1

5% f

or 3

.50m

to

4m a

nd 2

0% f

or a

bove

4m

dep

th

over

bas

ic r

ates

are

allo

wed

.3

.Th

e ab

ove

data

doe

s no

t in

clud

e ba

iling

cha

rges

, ba

iling

cha

rges

to

be a

dded

as

extr

a as

per

rat

es g

iven

in t

he r

elev

ant

PWD

Sch

edul

e of

Rat

es o

r as

per

act

uals

.4

.Th

e co

nvey

ance

cha

rges

ado

pted

for

Cem

ent,

San

d &

Pip

es a

re o

nly

for

illus

trat

ion

purp

ose.

The

ave

rage

lea

d fo

r re

spec

tive

dist

ricts

, as

app

rove

d by

the

Chi

efEn

gine

er s

hall

be a

dopt

ed f

or C

emen

t &

San

d. T

he l

ead

for

Pipe

sha

ll be

ado

pted

, as

cer

tifie

d by

the

res

pect

ive

Assi

stan

t Ex

ecut

ive

Engi

neer

.5

.Th

e Ba

sic

Rat

e ad

opte

d un

der

this

Hea

d “

Rat

es o

f W

orks

” is

exc

lusi

ve o

f al

l tax

es a

nd G

ST

Total cost of laying and jointingSW pipes with CM and packingwith spun or tarred yarn etc.

complete for 30m length (Rs.P)

Testing charges includingconveyance of water tools and

plants etc. ( Rs.)

Diameter (in mm)

Total cost of laying 4 jointsstoneware pipes complete for

1 metre ( Rs. P )

264

.

265

IV (B) RATES FOR EARTH WORKEXCAVATION OTHER THAN PIPE

LAYING WORKS AND OPEN WELLS

266

.

267

EARTH EXCAVATION OTHER THAN PIPE LAYING WORKS AND OPEN WELLS

Schedule Rates for


Earthwork excavating and depositing on bankwith an initial lead of 10 metres and initial liftof 2 metres in

1 Sand, silt or other loose soil, wet sand or siltnot under water, light black cotton soil, sandyloam and ordinary soil including excavatedearth SS 20 A

2 Sand, silt or other loose soil, wet sand or siltnot under water, light black cotton soil, sandyloam and ordinary soil including excavatedearth SS 20 B

3 Slush and silt under water upto 0.75 metredepth requiring the aid of baskets and vesselsSS 20 B

4 Trimming the bed and side slope of the bank inall soils except hard rock upto a thickness of7.5 cm and making it ready to receive theconcrete.

4a 7.50 cm to 15cm thick5 Sectioning during forming bunds when earth

moving machinery, lorries and rollers are usedfor consolidation.

6 Hard stiff clay, stiff black cotton, hard redearth, shales, murram, gravel, stoney earthand earth mixed with small size boulders SS20A

7 Hard stiff clay, stiff black cotton, hard redearth, shales, murram, gravel, stoney earthand earth mixed with small size boulders SS20B

8 Soft disintegrated rock, laterite, soft rock orkankar, not requiring blasting

9 In loose boulders in excavation of various sizes150mm to 625mm

10 Medium Rock and Dense Medium Rock notrequiring blasting

11 Extra for every additional 10 metres lead orpart thereof over the initial lead

12 Extra for every additional 1 metre lift or partthereof over the initial lift

Cu.m 61.50

Cu.m 56.10

Cu.m 70.20

Sq.m 14.30

Sq.m 17.30

Cu.m 10.50

Cu.m 89.50

Cu.m 84.00

Cu.m 125.20

Cu.m 198.70

Cu.m 219.80

Cu.m 10.20

Cu.m 8.10

268

13 Breaking clods, consolidating and sectioning14 Breaking clods, consolidating and sectioning

the earth scooped by bull dozers15 Add relevant TNDSS No.20A, rates for new

tank bunds and closing breaches for extrawatering and consolidation.

a) By hand rollerb) By power roller including hire charges16 Benching old embankment slopes 45cm x 45cm17 Puddle wall work18 Turfing in slopes including watering and fixing

with initial lead upto 50m.19a Refilling with excavated sand complying with

standard specification for filling in foundationand basement

19.b Refilling with excavated soil (other than sand)complying with the standard specification forfilling in foundation and basement

20 QUARRYING AND BLASTINGa) Hard rock measured in solid including blasting

and stackingb) Removing hard rock by wedging chiselling and

trimming to proper shape where blasting isprohibited.

c) Medium rock and dense medium rock requiringblasting

d) Extra for every additional 10 metres lead orpart thereof over the initial lead for blastedmaterials

e) Extra for every additional 1 metre lift or partthereof over the initial lift of 2 m for blastedmaterials

f) Benching hard rock upto an average 10cmdepth

g) Drilling holes in hard granite 32mm diameterh) Drilling holes in hard granite 40mm diameteri) Drilling holes in hard granite 45mm diameterj) Drilling holes in hard granite 50mm diameterk) Drilling holes in hard granite 75mm diameter

Schedule Rates for


Cu.m 5.00

Cu.m 15.50

Cu.m 17.30Cu.m 29.30Sq.m 3.20Cu.m 138.80

Sq.m 29.30

Cu.m 25.70

Cu.m 29.30

Cu.m 594.00

Cu.m 1190.00

Cu.m 303.00

Cu.m 7.10

Cu.m 7.30

Sq.m 575.00

RM 161.00RM 190.00RM 223.00RM 267.00RM 304.00

269

The following foot note is applicable for the classifications of soils come under “ Quarryingand blasting” and “Earth Work”

Note: a) Standard specification No.20-A requires breaking clods, ramming and sectioningof spoil bank for which separate rate will not be paid.

b) Standard specification No.20-B does not require breaking clods, ramming andsectioning but requires neat banking in accordance with the standardspecifications.

c) Double the relevant rate for standard specification No.20-B will apply toexcavation in all the soils and rock classification given above for foundation ofbuildings, piers, wings and returns of bridges, culverts, sluices, regulators andcross masonry works, retaining walls, toe walls, cut-off walls and body walls ofanicuts weirs, retaining walls of cause ways, bed dam, pits for avenue trees,and pits for poles and towards catch water pits and pipe laying trenches forwater supply and sewerage works.

d) An extra 50 percent over the rates for ordinary excavation in all the soils androck classification given above shall be allowed for drains, channels, contourtrenches and canals having bed width of 1.25 m and below. The extra percentageis applicable any for depth up to 2.00m the depth being measured from thebottom of excavation.

e) An extra 25 percent over the rates for ordinary excavation in all the soils androck classification given shall be allowed for drains, channels and canals havingbed width of 1.25m to 2.00m. The extra percentage is applicable only fordepth up to 2.0m the depth being measured from the bottom of excavation.

f) These rates for earth work do not include bailing charge. The bailing chargesare to be paid as per actual in case bailing is done departmentally or at actualplus 10 percent extra in case bailing is done by other agencies. However forestimate purpose bailing charges are to be provided at 10 percent of the ratesof respective items of excavation in all soils including medium rock and densemedium rock and at 5 percent of the rates for excavation in hard rock.

g) Double the relevant rate for standard specification No.20B for excavation in allsoils and rock classification given above shall be allowed for circular trenchesfor soil and moisture conservation having bed width of 0.25m and below withside slope of 1/2:1 and not less than 0.75 m in depth.

h i) A deduction of 40 percent is to be made for the quantity of voids and stackmeasurement and payment is for the lesser of two viz. Solid measurement orstack measurements minus 40 percent of stack measurement for voids.

h ii) The rates for extra lead and lift are on the quantity as per the solid measurementor stack measurement less 40 percent for voids whichever is less. These ratesare applicable for head load only.

h iii) Payment for blasting the rock in solid shall be made for the lesser of the twoquantities obtained by a) Measurement recorded by levels or measurementand b) by stack measurement less deduction for voids (This foot note isapplicable for all items of rock measured in solid)

270

.

271

IV (C) RATES FOR EARTH WORKEXCAVATION PIPE LAYING WORKS FORWATER SUPPLY AND SEWERAGE WORKS

272

.

273

EARTH WORK EXCAVATION FOR PIPE LAYING WORKS FOR WATER SUPPLY ANDSEWERAGE WORKS

Schedule Rates for


I Earth work excavation and depositing on bankwith initial lead of 10 m and lift of 2 M innarrow trenches having bed width 1.25m &below for laying of pipes for water supply andsewerage works in the following type of soilsas directed by Departmental officers

a Sand, silt or other loose soil, wet sand or siltnot under water light black cotton soil, sandyloam and ordinary soil.SS20B

b Hard stiff clay, stiff black cotton, hard redearth, shales, murram gravel, stoney earth andearth mixed with small size boulders and hardgravelly soil.SS20B

II Earth work excavation and depositing on bankwithinitial lead of 10m and lift of 2.00m innarrow trenches for laying of pipes for watersupply and sewerage works in the followingtypes of soil strata as directed bydepartmental officers

a In Soft Disintegrated Rock, Laterite, soft rockor kankar, not requiring blasting.

b In Medium rock and dense medium rock notrequiring blasting.

c In Medium rock and Dense medium rock requiringblasting.

d In hard rock including blasting, removal andstacking.

III a) Earth work excavation for Pipe Laying work byremoving dense medium rock using controlledblasting method by drilling blast holes usingcompressor and jack hammer includingdewatering wherever necessary, cost ofgelatin, electric detonator, licensed shotfireman, labour for filling earth in gunny bags,labour for excavation of earth, conveyanceof earth including cost of gunny bags, M.S.Plates, barricading, putting up road diversionboards and providing red light signal duringnight, removal of debris etc., where open blastingis prohibited and as directed by the TWADBoard Officers.

One cubic 140.25metre

One cubicmetre 210.00

Cum 251.00

Cum 439.60

Cum 606.00

Cum 1188.00

Cum 700.00

274

b Earth work excavation for Pipe Laying work byremoving hard rock using controlled blastingmethod by drilling blast holes using compressorand jack hammer including stacking,dewatering wherever necessary, cost ofgelatin, electric detonator, licensed shotfireman, labour for filling earth in gunny bags,labour for excavation of earth, conveyanceof earth including cost of gunny bags, M.S.Plates, barricading, putting up road diversionboards and providing red light signal duringnight, removal of debris etc., where upenblasting is prohibited and as directed by TWADBoard Officers.

Schedule Rates for


Cum 1280.00

275

IV (D) RATES FOR EARTH WORKEXCAVATION AND REFILLING FOR

PIPELINE WORKS HAVING BED WIDTH OF1.25M AND BELOW ON LINEAR

MEASUREMENT BASIS

276

.

277

Cost of EWE 210

Cost of refilling 29.30

Cost of loose soil 140.25

CI/DI/ 80 0.75 1.05 0.79 0.098 0.780 165.90 110.80 22.85

MS 100 0.75 1.05 0.79 0.118 0.777 165.90 110.80 22.77

125 0.75 1.05 0.79 0.144 0.771 165.90 110.80 22.59

150 0.75 1.05 0.79 0.170 0.765 165.90 110.80 22.41

200 0.80 1.10 0.88 0.222 0.841 184.80 123.42 24.64

250 0.80 1.20 0.96 0.274 0.901 201.60 134.64 26.40

300 0.80 1.35 1.08 0.326 0.997 226.80 151.47 29.21

350 0.90 1.45 1.31 0.378 1.193 275.10 183.73 34.95

400 0.90 1.55 1.40 0.429 1.251 294.00 196.35 36.65

450 1.00 1.70 1.70 0.480 1.519 357.00 238.43 44.51

500 1.00 1.85 1.85 0.532 1.628 388.50 259.46 47.70

525 1.00 1.85 1.85 0.532 1.628 388.50 259.46 47.70

80 0.75 1.05 0.79 0.104 0.779 165.90 110.80 22.82

AC CI 15 100 0.75 1.05 0.79 0.124 0.775 165.90 110.80 22.71

125 0.75 1.05 0.79 0.151 0.770 165.90 110.80 22.56

150 0.75 1.05 0.79 0.178 0.763 165.90 110.80 22.36

200 0.80 1.10 0.88 0.235 0.837 184.80 123.42 24.52

250 0.80 1.20 0.96 0.286 0.896 201.60 134.64 26.25

300 0.80 1.35 1.08 0.340 0.989 226.80 151.47 28.98

350 0.90 1.45 1.31 0.396 1.162 275.10 183.73 34.05

400 0.90 1.55 1.40 0.452 1.235 294.00 196.35 36.19

450 1.00 1.70 1.70 0.502 1.502 357.00 238.43 44.01

500 1.00 1.85 1.85 0.559 1.605 388.50 259.46 47.03

AC CI 10 80 0.75 1.05 0.79 0.104 0.779 165.90 110.80 22.82

100 0.75 1.05 0.79 0.124 0.775 165.90 110.80 22.71

125 0.75 1.05 0.79 0.140 0.772 165.90 110.80 22.62

THE RATES FOR EARTH WORK EXCAVATION AND REFILLING FOR PIPE LINE WORKSHAVING BED WIDTH OF 1.25M AND BELOW ON LINEAR MEASUREMENT BASIS

Type

Pipesize in

mm

BedWidthin ‘m’

Depthin ‘m’

Earthwork

qty. incum/m

Outerdia ofpipe in

‘m’

RefillingQty/

cum/m

Earthwork

rate forotherthanloosesoil/mRs.

Earthwork

rate forloosesoil/m

Rs.

Refillingrate/m

Rs.

278

Type

Pipesize in

mm

BedWidthin ‘m’

Depthin ‘m’

Earthwork

qty. incum/m

Outerdia ofpipe in

‘m’

RefillingQty/

cum/m

Earthwork


Earthwork

rate forloosesoil/m

Rs.

Refillingrate/m

Rs.150 0.75 1.05 0.79 0.175 0.763 165.90 110.80 22.36

200 0.80 1.10 0.88 0.229 0.839 184.80 123.42 24.58

250 0.80 1.20 0.96 0.281 0.898 201.60 134.64 26.31

300 0.80 1.35 1.08 0.333 0.993 226.80 151.47 29.09

350 0.90 1.45 1.31 0.389 1.186 275.10 183.73 34.75

400 0.90 1.55 1.40 0.436 1.246 294.00 196.35 36.51

450 1.00 1.70 1.70 0.486 1.515 357.00 238.43 44.39

500 1.00 1.85 1.85 0.541 1.620 388.50 259.46 47.47

PVC/

HDPE/

GRP 40 0.60 1.05 0.63 0.040 0.629 132.30 88.36 18.43

50 0.60 1.05 0.63 0.050 0.628 132.30 88.36 18.40

63 0.60 1.05 0.63 0.063 0.627 132.30 88.36 18.37

75 0.60 1.05 0.63 0.075 0.626 132.30 88.36 18.34

90 0.60 1.05 0.63 0.090 0.624 132.30 88.36 18.28

110 0.60 1.05 0.63 0.110 0.621 132.30 88.36 18.20

125 0.60 1.05 0.63 0.125 0.618 132.30 88.36 18.11

140 0.60 1.05 0.63 0.140 0.615 132.30 88.36 18.02

160 0.60 1.05 0.63 0.160 0.610 132.30 88.36 17.87

180 0.75 1.05 0.79 0.180 0.760 165.90 110.80 22.27

200 0.80 1.10 0.88 0.200 0.850 184.80 123.42 24.91

PSC/

BWSC 350 0.90 1.45 1.31 0.464 1.136 275.10 183.73 33.28

400 0.90 1.55 1.40 0.514 1.188 294.00 196.35 34.81

450 1.00 1.70 1.70 0.564 1.450 357.00 238.43 42.49

500 1.00 1.85 1.85 0.614 1.554 388.50 259.46 45.53

15 0.75 1.05 0.79 0.020 0.787 165.90 110.80 23.06

20 0.75 1.05 0.79 0.030 0.787 165.90 110.80 23.06

25 0.75 1.05 0.79 0.030 0.787 165.90 110.80 23.06

32 0.75 1.05 0.79 0.040 0.786 165.90 110.80 23.03

279

Type

Pipesize in

mm

BedWidthin ‘m’

Depthin ‘m’

Earthwork

qty. incum/m

Outerdia ofpipe in

‘m’

RefillingQty/

cum/m

Earthwork


Earthwork

rate forloosesoil/m

Rs.

Refillingrate/m

Rs.

Note:(i) For earthwork excavation of loose soil and ordinary Soil SS20B

a) The bed width less than 1.25m and for depth more than 2.00 m and

b) The bed width more than 1.25m and for depth more than 2.00m

The quantities may be wored out seperately with extra cost as per note (e) of

IV B & Additional lift charges for every additional in may be adopted.

(ii) Earthwork excavation in SDR, DMR,HR etc., the linear measurement rate may be

worked out separately and to be approved by the SE concerned after verification

of soil classifications by putting proper trial pits at closer intervals”.( B.P.Ms.No.82

/ COM Wing / dt.22.8.2008).

40 0.75 1.05 0.79 0.050 0.786 165.90 110.80 23.03

50 0.75 1.05 0.79 0.060 0.786 165.90 110.80 23.03

65 0.75 1.05 0.79 0.070 0.784 165.90 110.80 22.97

80 0.75 1.05 0.79 0.090 0.781 165.90 110.80 22.88

100 0.75 1.05 0.79 0.110 0.778 165.90 110.80 22.80

125 0.75 1.05 0.79 0.140 0.772 165.90 110.80 22.62

150 0.75 1.05 0.79 0.160 0.767 165.90 110.80 22.47

280

.

IV (E) RATES FOR MISCELLANEOUSITEMS

282

.

283

MISCELLANEOUS

Schedule Rates for


PLUMBING

1. A Laying of G.I. Pipes and specials to properline and level including jointing but excludingcost of pipes and jointing materials forplumbing works for providing water supplyand sanitary works in the premises of thebuilding6 mm to 32 mm dia One metre 17.2540 mm to 50 mm dia One metre 17.2565 mm to 150 mm dia One metre 23.10

b Bore cap using M.S. Flat of size 1 cm x 3 mmand M.S. sheet on top with bolt ingarrangements for securing the cap in position(Bore caps with M.S. Couplings need not bemade)5" Casing Pipes Each 482.036" Casing Pipes Each 510.838 “ Casing Pipes Each 561.52

2 Labour for cutting open road for layingwater mains or sewer.

a. B.T. Roads (or) Maccadam road One cu.m 707.75b. Concrete Roads One cu.m 991.213 Labour for drilling, cutting, Threading and

Fixing Ferrules in distribution pipes.10 mm dia Each 73.9415 mm dia Each 92.6920mm dia Each 116.3825 mm dia Each 137.68

4 Labour charges for Painting TWAD BoardEmblem in accordance with the size andspecifications as approved by the Board onthe Service Reservoirs including cost of allconsumables, one coat of base paint,scaffolding charges including painting NRDWPLogo on the Service Reservoirs.

5 Drilling holes in C.I/G.I. Dummy Flanges.12 mm dia Each 25.9515 mm dia Each 52.19

Sqm 2599.43

284

Schedule Rates for


20 mm dia Each 75.5922 mm dia Each 101.8425 mm dia Each 127.93

6 Labour for refilling with sand the sockethollows of pipes including conveyance and One cu.m 25.95stackingNOTE : 1) For depth between Percentage

excessallowed overbasic rate

2 m to 4 m 15%4 m to 6 m 30%

7 Lifting and positioning of C.I / G.I /DI/MSPipes in vertical direction for servicereservoir pipe connection0 to 2 m Qtl 219.872 to 4 m Qtl 331.154 to 6 m Qtl 519.386 m to 8 m Qtl 718.408 m to 10 m Qtl 917.2710 m to 12 m Qtl 1113.5912 m to 14 m Qtl 1317.5614 m to 16 m Qtl 1500.8316 m to 18 m Qtl 1699.4118 m to 20 m Qtl 1898.1320 m to 22 m Qtl 2092.0522 m to 24 m Qtl 2287.92

8. DRILLING WORKSUsing Hand Bore set

a Drilling of borewells of size 4" to 5" dia. inSedimentary formation using hand boresetsincluding insertion of casing pipes and removal One metre 829.53of casing pipes etc., including supplying andpacking of pebbles and conveyance of handBoreset including loading and unloading

b Drilling of borewells of size 6" to 8" dia. insedimentary formation using hand boresetincluding insertion of casing pipe etc., andsupplying and packing of pebbles One metre 975.61(Conveyance of hand bore set includingloading and unloading to be done by thecontractor)

285

Schedule Rates for


c Using Hand Bore set

(For Investigation purpose)

I Drilling of borewells of size 4" to 5" dia. insedimentary formation using hand boresetsincluding insertion of casing pipes and removal One metre 617.61of casing pipes etc., including collection ofsamples as directed by the TWAD BoardOfficers.

ii Drilling of borewells of size 6" to 8" dia. insedimentary formation using hand boresetsincluding insertion of casing pipes and removal One metre 723.65of casing pipes etc., including collection ofsamples as directed by the TWADBoard Officers.Using Calyx Drill

d Drilling of 4 1/2" diameter borewell by usingCalyx Drill including transporting charges andinsertion of casing pipes (excluding cost ofcasing pipe)

i. For Hilly terrain area One metre 3104.85ii. For Plain area One metre 2565.38e Drilling 4 1/2" dia meter bores by using

In-Well rig in Hilly areas One metre 1306.61

f Reaming from 6" Pilot bore to 12" size boreas directed by the TWAD Board Officers One metre 341.05

g Labour charges for inserting casing pipesassembly (With slot or without slot) in thedrilled hole including welding the joint etc., One metre 326.65complete and supplying and packing theannular space with pebbles of size and qualityas approved by the Executive Engineer

9 a Driving sheet piles for one metre length ofgallery each side in sandy soil

i. First depth of 2 m One metre 644.16ii Second depth of 2 m One metre 983.56iii Third depth of 2 m One metre 1847.28b Removing sheet piles from one metre length

of gallery on each side including stackingthe sheet piles properly

286

Schedule Rates for


i. First depth of 2 m One metre 100.19ii Second depth of 2m One metre 153.43iii Third depth of 2 m One metre 222.7210 Drilling of borwell inside well 115mm dia.

a) Vertical One metre 713.15b) Horizontal One metre 782.14

11 Drilling of borewell inside well 150mm dia.a) Vertical One metre 892.82b)Horizontal One metre 943.66

12 Drilling of Borewells anywhere in Tamilnaduincluding transportation from one place toanother within Tamilnadu in alluvial soilsedimentary strata of clay and sand stoneshale pebbles boulders etc. By first takinga pilot bore of 140 mm/150mm dia and thenenlarging to required dia direct or reverserotary mud circulation method using rotaryrigs, fuel, labour and drilling bentonite andwater required for drilling at site ( Site willbe shown by the TWAD Board Officers)including construction of mud pit.

a. Drilling of 140/150 mm pilot borei. Upto 60 m Depth ending below ground level One metre 1491.39ii From 60 m upto 90 m Depth ending from

ground level One metre 1615.12iii From 90 m upto 120 m Depth ending from

ground level One metre 1712.45iv From 120 m upto 150 m Depth ending from

ground level One metre 1803.19v From 150 m upto 180 m Depth ending from

ground level One metre 1831.24vi From 180 m upto 210 m Depth ending from

ground level One metre 1890.63vii From 210 m upto 240 m Depth ending from

ground level One metre 1945.07viii From 240 m upto 270 m Depth ending from

ground level One metre 2012.71ix From 270 m upto 300 m Depth ending from

ground level One metre 2057.25x From 300 m upto 330 m Depth ending from

ground level One metre 2106.75

P.S. toM.D.S.S.Special

Specifications

287

Schedule Rates for


xi From 330 m upto 360 m Depth ending fromground level One metre 2151.29

12 b Reaming 140/150 mm dia pilot bore to 300mm diabore as directed by the TWAD Board Officer.

i. Upto 60 m depth ending below ground level One metre 374.50ii From 60 m depth and upto 90 mt depth ending

below ground level One metre 397.59iii From 90 m upto 120 mt depth ending below

ground level One metre 423.99iv From 120 m upto 150 mt depth ending below

ground level One metre 430.59v From 150 m upto 180 mt depth ending below

ground level One metre 450.39vi From 180 m upto 210 mt depth ending below

ground level One metre 473.48vii From 210 m upto 240 mt depth ending below

ground level One metre 494.93viii From 240 m upto 270 mt depth ending below

ground level One metre 513.08ix From 270 m upto 300 mt depth ending below

ground level One metre 541.12x From 300 m upto 330 mt depth ending below

ground level One metre 562.57xi From 330 m upto 360 mt depth ending below

ground level One metre 582.3712 c Reaming 200 mm dia pilot bore to 350mm dia

bore as directed by the TWAD Board Officer.i. Upto 60 m depth ending below ground level One metre 420.69ii From 60 m depth and upto 90 mt depth ending

below ground level One metre 445.44iii From 90 m upto 120 m depth ending below

ground level One metre 473.48iv From 120 m upto 150 m depth ending below

ground level One metre 488.33v From 150 m upto 180 m depth ending below

ground level One metre 504.83vi From 180 m upto 210 m depth ending below

ground level One metre 542.77vii From 210 m upto 240 m depth ending below

ground level One metre 620.31

288

Schedule Rates for


viii From 240 m upto 270 m depth ending belowground level One metre 636.81

ix From 270 m upto 300 m depth ending belowground level One metre 651.66

x From 300 m upto 330 m depth ending belowground level One metre 673.10

xi From 330 m upto 360 m depth ending belowground level One metre 689.60

12 d Reaming 300 mm dia pilot bore to 400mm/450mmdia bore as directed by the TWAD Board Officer.

i. Upto 60 m depth ending below ground level One metre 577.42ii From 60 m depth and upto 90 m depth ending

below ground level One metre 646.71iii From 90 m upto 120 m depth ending below

ground level One metre 689.60iv From 120 m upto 150 m depth ending below

ground level One metre 730.84v From 150 m upto 180 m depth ending below

ground level One metre 760.54vi From 180 m upto 210 m depth ending below

ground level One metre 781.99vii From 210 m upto 240 m depth ending below

ground level One metre 800.13viii From 240 m upto 270 m depth ending below

ground level One metre 838.08ix From 270 m upto 300 m depth ending below

ground level One metre 869.42x From 300 m upto 330 m depth ending below

ground level One metre 912.32xi From 330 m upto 360 m depth ending below

ground level One metre 943.6612 e Labour Charges for inserting 150 mm/200mm/

250 mm dia (M.S. Casing pipes assembly withslots or with out slots) in the drilled holeincluding welding the joints etc., completeand supplying and packing the annular spacewith pebbles of size and quality as approvedby the Executive Engineers of TWAD Board.

289

Schedule Rates for


i. 150 mm dia Casing Pipes assembly One metre 336.25ii 200 mm dia Casing Pipes assembly One metre 336.25iii 250 mm dia Casing Pipes assembly One metre 341.95

13 a Labour Charges for inserting PVC Casing pipesassembly (with slots or without slots) in thedrilled hole including jointing the pipes withPVC Couplers with Cement paste etc.,complete, supply and packing the annularspace with pebbles of size and quality asapproved by the Executive Engineers ofTWAD Board

i. 150 mm dia Casing Pipes assembly One metre 325.90ii 200 mm dia Casing Pipes assembly One metre 336.25iii 250 mm dia Casing Pipes assembly One metre 336.25

13 b Charges for developing the Borewell with aircompressor of 600 CFM capacity (Minimum8 Hours) including transportation, labour and One hour 2197.93fuel charges for compressor as directed byTWAD Officers and conducting yield test by‘V’ notch method.Note :I) 150 mm dia bore, reaming should be doneupto 300mm dia.II) 200 mm dia bore, reaming should be doneupto 300mm dia and thereafter 400,450 etc.

14 Drilling of borewell anywhere in Tamilnaduincluding transportation from one place toanother place within Tamilnadu in alluvial soilor sedimentary strata of clay and sand orsand, stone, shale, pebbles, boulders etc.,by first taking a pilot bore of 140 mm/150mmdia and then enlarging to required dia bydirect or reverse rotatry mud and circulationmethod using Contractor’s rig, fuel, labour,drilling, betonite mud and water required fordrilling at the site shown by the TWADOfficers including construction of mud pit(only Calyx drills are to be used).

a. Drilling 140 / 150 mm dia Pilot Bore upto 60mdepth ending below ground level. One metre 1087.19

290

Schedule Rates for


b. Reaming from 140/150 mm dia pilot bore to300 mm dia bore as directed by the TWAD One metre 306.86Board Officers upto 60 m Depth ending fromground level

c. Labour charges for inserting 150 mm dia M.S.Casing pipes assembly (With slots or withoutslots) in the drilled hole including welding the One metre 275.81joints and packing annular space with pebblesof size and quality as approved by theExecutive Engineer / TWAD Board

d. Labour Charges for inserting PVC casing pipesassembly (with slots or without slots) in thedrilled hole including jointing the pipes withPVC couplers with cement paste etc.complete

i. 140 mm OD PVC Casing Pipes Assembly One metre 235.92ii 165 mm/168 mm dia PVC Casing pipes Assembly One metre 275.81e. Charges for developing the borewell with air

compressor of 300 CFM capacity (Minimum8 Hours) including transportation labour and One hour 1709.45fuel charges for compressor as directed byTWAD Board Officers and conducting yieldtest by ‘V’ notch method.

f. Drilling of 12" dia vertical borewell so as tohave a finished size of 6" dia borewell inboulder area to any required depth as decidedby the TWAD Board Off icers includingTransportation from one place to anotherplace with in Tamilnadu State by direct or One metre 2092.35reverse rotary mud circulation method usingContractor’s r ig tools, fuel, labourers,bentonite mud and water required for drillingat the site shown by the TWAD Officersincluding construction of mud pit etc. usingonly calyx rigs.

15 a. Conveyance of Hand Pumps and its accessoriesfrom divisional stores to site of works

i. Conveyance upto 10 Kms 626.76ii Conveyance 10 to 20 Kms 786.64ii Conveyance 20 to 40 Kms 958.66iv Conveyance above 40 Kms 1111.04

Each HandPump and itsaccessories

291

Schedule Rates for


Note :i) Conveyance of Filter Point, Handpump

with GI Pipes and its accessories fromdivisional stores to site of works. 50% ofthe rate of conveyance of hand pumps,with its accessories is applicable for thisitem for the respective leads as indicatedabove

ii) If the Mark II hand pump is conveyed incart track even for part distance 20 %extra over the above rate shall beadopted.

b i. Erection of deep well hand pumps upto 40 m Each 1110.74ii Above 40 m Each 1267.17c. Erection of shallow well hand pumps Each 490.28d. Erection Extra deep well hand pumps Each 1434.24e. Removal of deep well hand pumps from

borewelli. Up to 40 m Each 1110.74ii Above 40 m Each 1399.75f) Attending repairs to deep well handpumps

for borewells inclusive of removal of G.I.Pipes, Plunger rods, Cylinder and re-erectionof hand pumps inclusive of lowering the GIPipes Plunger rods cylinder, jointing etc.

i. Upto 30 M Each 1179.58ii) Above 30 M Each 1379.20

16 a Erection of filter point with G.I. Pipes of32 mm to 65 mm dia. Each 320.65

b Removing the chocked filter point with G.I.Pipes of 32 mm to 65 mm dia and re-erectingin another place within 1.00 KM radius after Each 532.87cleaning the filter points G.I. Pipes etc.,Complete upto 8 m depth

17a ERECTION OF POWER PUMPSET INBORE/OPENWELLLabour Charges for erection of Horizontal shaft,centrifugal pumpset (Coupled/Monoblock) in

bore well/Open well including fixing of suction

pipe and foot valve upto a maximum depth

292

Schedule Rates for


of 7 metres and delivery pipes to the requiredlength with valves, pressure gauges upto theexterior wall of pump room and erection ofpanel board consisting of TPIC switchesstarter, Voltmeter, Ammeter, Capacitor singlephasing preventor and laying and jointing thecables and twin earthing as per IE rulesincluding providing bed blocks etc., completeand operating the pumps and trial run for 10days including signing of completion ofreports as required by EB authorities.

i. Upto 3 HP Each 7176.47ii Above 3 HP upto 7.5 HP Each 9237.02iii Above 7.5 HP to 20 HP Each 10824.09iv Above 20HP to 30 HP Each 12113.64v Above 30 HP to 40 HP Each 15693.24vi Above 40Hp to 50HP Each 21886.86

17 b ERECTION OF POWER PUMPS IN BORE WELLLabour charges for erection of twin packerduplex type jet pumps in borewells upto 150mm dia including fixing of Suction piperegulating valves with jet assembly upto amaximum depth of 30 m and delivery pipevalves pressure gauges upto the exterior wallof pump room and erection of panel boardconsisting of TPICN switches starter,Voltmeter, Ammeter, three indicator lampscapacitor and laying and jointing the cablesand twin earthing as per IE rules etc.,complete and testing the pumps and trailrun for 10 days including signing ofcompletion of reports as required by EBauthorities and finishing the pipe holesincluding the foundation bolts, nuts andearth pits.

i. Upto 3 HP Each 9599.97ii Above 3 HP upto 7.5 HP Each 11216.73iii Beyond 7.5 HP upto 20 HP Each 12825.25

Note : If depth of erection exceeds beyond30 m 10% increase over the basic rate isallowed

293

17 c Labour charges for the erection of submersible

pumpset in borewell/openwell including fixingand jointing submersible cable with proper

clamps upto the starter to required depth

and also fixing of riser pipes to the requireddepth valves erection clamps, pressuregauges upto the exterior wall of pump roomand erection of panel board consisting ofTPICN switches starter, Voltmeter, Ammeter,three pilot (indicating) lamps capacitor singlephasing preventor, water level guard andlaying and jointing the cables and twinearthing as per IE rules etc., complete and

testing the pumpset and trail run for 10 days.i. Upto 5 HP Each 9758.34ii) Above 5.00 HP to 10.00 HP Each 11182.09iii) Above 10.00 HP to 20.00 HP Each 12406.21iv Above 20HP to 30 HP Each 13490.76v Above 30 HP to 40 HP Each 17191.20vi Above 40Hp to 50HP Each 22713.36

17 d Conveyance of power pumpset (centrifugal,jet and submersible) and its accessories fromdivisional stores to site of works.

i) Conveyance upto 10 Kms Each Power 1364.35Pump and its accessories pump and its

accessoriesConveyance 10 to 20 Kms -do- 1499.63Conveyance 20 to 40 Kms -do- 2219.83Conveyance 40 to 60 Kms -do- 2706.66Conveyance 60 to 80 Kms -do- 3552.39Conveyance above 80 Kms -do- 4073.71Note : For item 17 (a), (b) and (c)i. Removal of centrifugal pumpset/ jet pumps/

submersible pumpsets and its accessoriesfrom borewell/ open well for attending repairs50% of the rates mentioned under item 17(a), (b) and (c) may be allowed for therespective Horse power.

Schedule Rates for


294

Schedule Rates for


ii Re-erection of centrifugal pumpsets, jetpumpsets and its accessories into theborewell/ openwell after attending therepairs 50% of the rate mentioned underitem 17 (a), (b) and (c) may be allowed forrespective Horse power.

18 Hire charges :a Sheet piles (Larsen) Per Pile/

Per day 5.55

b Sheet piles (For dingham) Per Pile/Per day 8.55

c Compartment sheet with Grills (3' - 0" Wide) Per sheet/Per day 8.55

d Rate for flushing of borewell of 6" dia requiringless than 4 hours operation using drill rods/hose with required size of pipes for variouscapacity compressor including transportation,labour, and fuel charges for compressors asdirected by the TWAD Officer and conductingyield test by ‘V’ notch method if required.

i. 600 Cfm ( 100 /150 PSI) 1 hour (or)Part there of 2197.63

ii) 300/250 Cfm (100 PSI) 1 hour (or)Part there of 1709.45

iii) 125 Cfm (100 PSI) 1 hour (or)Part there of 1566.07

Note : Minimum charges for 8 (eight) hourswill be levied if the air compressor issued forother departmental works or if the aircompressor is hired to other departments.

e Helmet Per day/8 hours 8.35

f Hand test pump Per day/8 hours 79.44

g Pile hammer Per day/8 hours 8.35

h Concrete mixer 5 Cft. With driver(Excluding Per day/cost of fuel) 8 hours 750.04

i. Concrete mixer 7 Cft. With driver(Excluding Per day/cost of fuel) 8 hours 1131.89

j Hand operated winch Per day/8 hours 73.87

k Pile cap Per day/8 hours 19.79

295

Schedule Rates for


l Dewatering using 3hp to 70hp diesel enginepumpset including Hire charges, cost of Diesel,Engine oil, pump operator, labour charges,conveyance of pumpset and fuel to site andback, loading, unloading and any otherincidental charges etc., complete.

(i) Hire charges for Diesel Pump set for 3 HP Per Hour 201.93ii) Hire charges for Diesel Pump set for 5 HP Per Hour 254.60iii) Hire charges for Diesel Pump set for 7.5 HP Per Hour 350.44iv) Hire charges for Diesel Pump set for 10 HP Per Hour 451.28v) Hire charges for Diesel Pump set for 12.5 HP Per Hour 517.12vi) Hire charges for Diesel Pump set for 15 HP Per Hour 577.96vii) Hire charges for Diesel Pump set for 20 HP Per Hour 699.64viii) Hire charges for Diesel Pump set for 40 HP Per Hour 1151.35ix) Hire charges for Diesel Pump set for 50 HP Per Hour 1359.71x) Hire charges for Diesel Pump set for 60 HP Per Hour 1603.07xi) Hire charges for Diesel Pump set for 70 HP Per Hour 1856.43m Hire charges for Centrifugal sludge

removal pumpset with fuel and crewcharges including transportations, fixingand dismantling.

a Upto 2 HP per hour 207.10b Above 2 HP to 5 HP per hour 269.23

19 a Labour for tying barbed wire fencinghorizontally through the holes in RCC posts One metre 8.55with required tension.

b Labour for tying barbed wire fencing verticallywith required tension One metre 8.55

20 Labour charges for putting bore holes of size3" to 4" in river bed in sandy and other loosesoils using hand boring sets including the costof hire charges, conveyance charges of hand One metre 447.84boring sets, collection of soil sample atfrequent intervals and as directed by TWADBoard Officers.

21 Desilting light or sandysoil or silt frominfiltration wells below water level including One cu.m. 1781.29the charges for special T&P and air compressoretc. complete.

296

Schedule Rates for


22 Surveying and levelling for the proposedalignment of pipe line by Total stationmethod by engaging qualified Engineers withminimum qualification of B.E.(Civil), TechnicalAsistant Grade I & II and Mazdoor category I,using the contractor own surveyinstruments, Special tools and plants vehiclehire charges, transportation, initial incidentalcharges such as jungle clearance etc.Preparation of Tree map and alignment plan,duly incorporating salient details, such astopographical features, permanent landmarks, bench marks etc. at appropriatepoints, alignment plans and longitudinalsection plan at 30 m intervals in addition toother sal ient locat ions such asbranches,bends,culverts, river crossingetc,with all field particulars in Auto Cad andsubmission of plan 3 set, along with LF bookswith making all entries with certification byabove qualified Engineers with soft copy andmarking TBM stones at required places withbench mark registers soft copies 3 set andhard copy 5 set etc., complete as directedby TWAD Board officers. 1 Km 3834.97

23 Dismantling

Dismantling, clearing away and carefullystacking materials useful for reuse for anythickness of walls

i Brick / stone in clay walls under 3 m high cu.m 51.50ii Brick / stone in clay walls, add for every additional

3 m or part there of over the initial height of 3 m cu.m 17.10iii Mud / sun dried brick walls under 3 m high cu.m 34.50iv Mud / sun dried brick walls,add for every additional

3 m or part thereof over the initial height of 3 m cu.m 9.80v Brick / stone masonry in lime mortar walls under

3 m high cu.m 157.50vi Brick / stone masonry in lime mortar walls, add

for every additional 3 m or part thereof overthe initial height of 3 m cu.m 17.40

297

vii Brick / stone masonry in Cement mortar wallsunder 3 m high cu.m 193.00

viii Brick / stone masonry in Cement mortar walls,add for every additional 3 m or part thereofover the initial height of 3 metre cu.m 20.40

ix Terracing work in roof or floor sqm 52.30x Flag stone in roof or floor including lifting sqm 27.60xi Cut stone slab over culverts upto 3.3.m height

below ground level cu.m 805.00xii Cut stone slab over culverts over 3.3.m height

below ground level cu.m 839.00xiii Removal of cut stone slabs / RCC Cover slabs sqm 350.00xiv Refixing cut stone slabs/ RCC Cover slab sqm 384.00xv Pantile or Mangalore tiled roof without roof timbers sqm 13.60xvi Flat and Pan tiles or Mangalore tiles over flat

tiles, without roof timbers sqm 19.00xvii Asbestos cement sheets roofing without roof

timbers sqm 12.10xviii Corrugated iron sheet roofing over pan tiles,

without roof timbers sqm 20.40xix Old Thatched roof, including tying materials

into small bundles for reuse sqm 5.90xx Wrought and put up framed timbers in roofs/floors cu.m 506.00xxi Doors and windows including removal of frames,

hinges and fastenings sqm 104.70xxii Drystone apron or revetment, stacking

within 40m lead cu.m 89.70xxiii Grouted stones apron or revetment, stacking

within 40 m lead cu.m 104.70xxiv Dry stone masonry walls cu.m 76.40xxv *Dismantling lime concrete cu.m 242.00xxvi *Dismantling plain cement concrete cu.m 332.00xxvii *Dismantling reinforced cement concrete cu.m 5045.00

Note* 1) The rate for dismantling limeconcrete, cement concrete and R.C. concreteare exclusive of bailing out water charges.The rate is same in all floors.2) For dismantling 0.70m below ground level25% extra over the basic rates (i.e. the ratesalready available in the schedule of rate) for

Schedule Rates for


298

dismantling is allowed.3. Add 25% extra for cause of restricted partialdismantling in existing structrue where extracare is required for safeguarding the mainstructure.

xxviii Dismantling RCC using deployingmachineries cu.m 3229.00

xxix Chipping of concrete and rougheningthe surface sqm 27.60

xxx Pressed tiles & weathering course sqm 31.40xxxi One course of pressed tile roof finish in

Cement Mortar sqm 17.40xxxii One course of terrace bricks roof finish in

Cement Mortar sqm 20.40xxxiii Two course of flat tiles roof finish in

Cement Mortar sqm 20.40xxxiv Mosaic-in-situ finish in cement mortar in

flooring and in wall surface sqm 43.20xxxv Floor finish and dadooing walls in Cement

Mortar with mosaic tiles/ glazed tiles/cuddapah slabs. sqm 41.60

xxxvi Clearing the sitea Clearing Heavy jungle sqm 5.90b Clearing Light jungle sqm 4.40c Clearing Scrub jungle sqm 4.10d Uprooting and removing large palmyrah/

coconut stumps each 120.70e Uprooting and removing small palmyrah/

coconut stumps each 86.70f Removing weeds in channel and drain sqm 1.60g Cleaning juliflora jungle with uprooting sqm 6.70h Cleaning juliflora jungle without uprooting sqm 5.10

Note : Definition of large and small stumps :The Diameter of Stumps shall be 1/3 of thecircumferance at a point 0.6 m above thehighest ground level at the stump or thecircumferance near the top of the stump ifthe stump is less than 0.60 m in height (Themeasurement for circumferance and

Schedule Rates for


299

determination of the diameter will be to thenearest full centimetre). Only stumps withCircumferance of 30 cm and more will bemeasured for payment. The Sl. No d, is forStumps of Diametre above 30 cm and Sl. No.e is for stumps of diametre 15 to 30 cm.

24. OPEN WELL EXCAVATION

1 Earth work open well excavation, complyingwith relevant clauses of T.N.D.S.S. Well sinkingand with lead up to 10 metres in sand, silt orother loose soil, Wet sand or silt not underwater, light black cotton soil, sandy loam andordinary soil - First depth of 2 metres. Cu.m 56.10

2 Earth work open well excavation, complyingwith relevant clauses of T.N.D.S.S. Well sinkingand with lead upto 10 metres in Hard stiffclay, stiff black cotton soil, hard red earth,shales,murrams gravel, stoney earth and earthmixed with small size boulders and hard gravellysoil - First depth of 2 metres Cu.m 83.80

3 Earth work open well excavation, complyingwith relevant clauses of T.N.D.S.S. Well sinkingand with lead up to 10 metres in softdisintegrated rock, laterite, soft rock or kankar,not requiring blasting - First depth of 2 metres Cu.m 129.00

4 Open well excavation, complying with relevantclauses of T.N.D.S.S. Well sinking and withlead up to 10m in Medium rock and Densemedium rock not requiring blasting. First depthof 2 metres Cu.m 207.80

5 Open well excavation complying with relevantclauses of T.N.D.S.S. well sinking and with leadup to 10m in Medium rock and Dense mediumrock requiring blasting. First depth of 2 metres Cu.m 311.60

6 Open well excavation complying with relevantclauses of T.N.D.S.S. well sinking and with leadup to 10m in hard granite measured in solidincluding blasting and stacking - First depthof 2 metres Cu.m 609.50

Schedule Rates for


300

Note : Open well Excavation

a) Up to 2m diameter of wells, 10 percent excess will be allowed over the basic ratesfor open well excavation.

b) The rates do not include bailing charges. If the dewatering is to be donedepartmentally, 10 percent of cost of excavation shall be allowed for dewateringfor estimate purposes. Actual or 10 percent whichever is less to be allowed fordewatering charges. For any expenditure above this percentage prior approval ofthe competent authority should be obtained.

c) Stage depth rates for well excavation” The stage depth for adopting the ratesfrom the schedule of rates should be reckoned from ground level only irrespectiveof the fact, whether there is parapet wall or not.

d) For open well excavation for rates up to 12m depth, the progression would be x,2x, 3x, 4x, 5x, and 6x and rate beyond 12 metre depth, the progression should be8x, 10x, 12x, 14x and 16x and so on.

Schedule Rates for


7 Sinking well in loose soils, light black cottonsoil, sandy loam and ordinary soil under waterincluding bailing or pumping charges if necessaryetc., complete - First depth of 2 metres Cu.m 87.00

8 Sinking well in sand, including bailing or pumpingcharges if necessary etc. complete - Firstdepth of 2 metres Cu.m 122.10

9 Sinking well in hard stiff clay, light black cottonsoil, hard red earth, shales, murram, gravel,stoney earth and earth mixed with small sizeboulders and hard gravelly soil including bailingor pumping charges if necessary etc. complete- First depth of 2 metres Cu.m 122.10

301

Schedule Rates for


25. RATE FOR EARTH WORK BY DEPLOYINGMACHINERIES

1 Earth work in all soils except hard rock requiringblasting and conveying for formation of bundwith lead of 0 to 100 metre deploying earthmoving machineries and tippers includingbenching, formation of bunds, breaking clods,sectioning etc., complete.

Cu.m 45.55

1.a. Earth work in all soils except hard rock requiringblasting and conveying for formation of bundwith an extra lead of every 100 metre or partthereof deploying earth moving machineriesand tippers including benching, formation ofbunds, breaking clods, sectioning etc.,complete.

Cu.m 3.60

2 Earth work deploying earth moving machineriesfor desilting channel and forming bund oneither side and depositing the earth on banksincluding jungle clearance etc., complete.

a. Having width upto 3 m Cu.m 26.85b. Having width of 3 m – 10 m Cu.m 32.953 Earth work excavation deploying earth moving

machineries for desilting channel having awidth of more than 10 m and forming bund oneither side and depositing the earth on banksincluding jungle clearance etc., complete.

Cu.m 38.30

26 Lift charges - concrete - Brick or stoneMasonry above or below ground levelNote: The rate for lime concrete, cementconcrete, reinforced cement concrete, brickwork and stone masonry worked out as perStandard Data will apply to basement andfoundation up to a depth of 1.50 m belowground level only (basic rate)Statement I

a) Concrete above ground level1 Add to the basic rate for works up to 4.50m

height in ground floor (height to be reckonedfrom floor level i.e. plinth level in ground level)

Cu.m 89.90

2 Add for works in every upper floor over therate of preceding floor Cu.m 177.00

302

3 Brick or stone masonry above ground leveli. Add to the basic rates for works up to 4.50m

height in ground floor (height to be reckonedfrom floor level i.e. plinth level in ground level) Cu.m 59.20

ii. Add for works in every upper floor over therate of preceeding floor Cu.m 119.30

Note: i) For the works above 4.5m height in individualfloor the rate of next floor may be taken.The extra rates allowed for building works areapplicable to irrigation works and road worksalso. The extra rates may be allowed for thestructures beyond 1.00m above ground level.

ii) The extra rates may be allowed consideringthe ground level as datum in respect of servicereservoirs (where there is no plinth level)Statement II

a) Concrete below ground level

1 Add the basic rate for works above 1.5m depthand upto 4.5m depth below ground level Cu.m 88.50

2 Add the basic rate for works above 4.5m depthand upto 9.0 m depth below ground level Cu.m 177.60

3 Add extra over the above item 2 for everyadditional 4.5m depth beyond 9m depth belowground level Cu.m 177.60

B) Brick or stone masonry below ground level

1 Add the basic rates for works above 1.5mdepth and up to 4.5m depth below ground level Cu.m 59.40

2 Add the basic rates for works above 4.5mdepth and up to 9.0m depth below ground level Cu.m 119.30

3 Add extra over the above item 2 for everyadditional 4.5m depth beyond 9m depth belowground level Cu.m 119.30Note :1. The above extra rates are applicable forbuildings, irrigations, and road works.2. First Grade stone includes hard granite, trap,etc. second Grade stone includes gneiss, limestone etc.3. The class of materials to be used shouldalways be defined in the items, description intender schedules, contract schedules etc.

Schedule Rates for


303

4. For reinforced cement concrete work, onlythe hardest locally available stone will be used,if it has good bonding surface and is otherwisesuitable proportions for concrete are definedin the relevant standard specification.5. Note under Sl.No.179 to 187 in the standarddata book applies to arches over doors andwindows. For large arches in bridges andirrigation works, addition to this rate, extracost of centering is to be made.

6 For concrete mixa. Equal mixes (i.e.) 50 percent mortar

mixes only should be adopted for plainconcrete for foundation, flooring and RCConcrete for roofs, lintels, etc. wherevercement is used with hard broken stonesor brick jelly.

b. 40 percent or 50 percent mortar mixermay be adopted where lime concrete withbrick aggregate is used according to thecondition at site.

27 CONCRETE VIBRATORS1 Where vibrators are specified for consolidation

in plain Cement concrete, this rate per cu.mover and above the provision made in thestandard data book for consolidation withmanual labour may be allowed. Cu.m 52.40

2 Where vibrators are specified for consolidationin RCC, this rate per cu. m over and abovethe provision made in the standard data bookfor consolidation with manual labour may beallowed. Cu.m 70.70

28 Plastering

1 Clean removal of lime plaster from walls andracking out joints 20mm deep or from terracedroofs racking out joints 12mm deep sq.m 7.10

2 Clean removal of lime plaster from walls sq.m 5.503 Clean removal of cement plaster from walls sq.m 5.804 Clean removal of cement plaster from walls

and racking out joints 20mm deep sq.m 7.70

Schedule Rates for


304

29 White washing and colour washing anddistempering

1 Thorough scrapping of old plastered surface sq.m 3.202 Washing of plastered surface with soap, soda

and water( or with soda, lime, brush and water) sq.m 4.0030 Painting, Wood Oiling, Tarring, Varnishing,

Bee’s Waxing etc1 Removing old paint from doors and windows

by blow lamp and scrapping, including removaland refitting of shutters sq.m 25.90

2 Removing old paint from doors and windowsby scrapping and refitting of shutters sq.m 10.90

3 Removing paint from doors, windows and woodworks by manual labour sq.m 7.40

4 Removing old paint from structural steel byblow lamp or sand paper sq.m 15.50

5 Scrapping and removing old paint fromstructural steel by manual labour sq.m 6.90

6 Removing old paint from iron surface with sandpaper sq.m 6.50

7 Repolishing the mosaic flooring includingpolishing stone and hire charges for polishingmachine but excluding cost of electrical charges. sq.m 15.30

31 MiscellaneousI. Supplying & filling up the empty Cement gunny

bags with sand, stitching them conveying thesame to site and stacking as directed within alead of 10m excluding cost of bags, jute,thread, needle, sand etc. (labour only) Bag 6.50

ii. Driving piles upto 15 cm dia in river bed RM 20.30iii. Pointing the edge and driving bamboo /

casurina/ eucalyptus piles into river bed forthe first 1m depth below groundlevel Each 17.30

iv. Driving bamboo/ Casurina/ eucalyptus piles intoground beyond 1m depth from ground level.For every 1m (or) part thereof RM 17.30

32 River Conservancy of Korambu Worksv. Brush wood bundles one metre girth and one

metre long within an initial lead of 1.6 KM One bundle 3.30vi. Extra for every additional lead of 1.6 KM (for

the above item) One bundle 0.39

Schedule Rates for


305

vii. Driving casurina piles into bed includingscaffolding etc., complete RM 8.40

viii. Casurina walling pieces 40mm to 50mmdiameter including fixing with nails and tyingwith ropes. RM 11.70

33 Labour wrought and put up for Doors,Windows and Ventilators

1 Labour wrought and put up in position of framesinclusive of fixing holdfasts for doors, windowsand ventilators etc. Cu.m 10275.00

2 Labour wrought and put up in position ofshutters for fully panelled doors (external orinternal) moulded panels including labourcharges for fixing furniture fittings, complyingwith standard drawings and standardspecification. sq.m 1155.00

3 Labour wrought and put up in position ofshutters for fully panelled doors internal fiveplywood panels including labour charges forfixing furniture fittings, complying with standarddrawings and standard specification. sq.m 963.00

4 Labour wrought and put up in position ofshutters for glazed and panelled doorsincluding labour charges for fixing furniturefittings, complying with standard drawings andstandard specification. sq.m 1078.00

5 Labour wrought and put up in position ofshutters for framed and planked doorsincluding labour charges for fixing furniturefittings, complying with standard drawings andstandard specification. sq.m 900.00

6 Labour wrought and put up in position ofshutters for ledged and braced and plankeddoors including labour charges for fixingfurniture fittings complying with standarddrawings and standard specification. sq.m 608.00

7 Labour wrought and put up in position ofshutters for glazed windows including labourcharges for fixing furniture fittings, complyingwith standard drawings and standardspecification. sq.m 1078.00

Schedule Rates for


306

8 Labour wrought and put up in position ofshutters for windows panelled includinglabour charges for fixing furniture fittings,complying with standard drawings andstandard specification. sq.m 1160.00

9 Labour wrought and put up in position ofshutters for windows, ledged, braced andplanked doors including labour charges for fixingfurniture fittings, complying with standarddrawings and standard specification. sq.m 608.00

10 Labour wrought and put up in position frames,shutters for ventilators glazed fixed doubleframes and with wire netting complete fixedin position in accordance with standarddrawings and standard specification. sq.m 963.00

11 Labour wrought and put up in position framesshutters for swing ventilators and fixed inposition in accordance with standard drawingsand standard specification. sq.m 901.00

12 Labour charges for fixing doors along withframes in position etc. complete(finished work) sq.m 171.30

13 Labour charges for fixing windows andventilators along with frames in position etc.complete sq.m 215.00

14 Labour wrought and put up in position flushshutters for single leaf shutters. sq.m 161.00

15 Labour wrought and put up in position flushshutters for Double leaf shutters sq.m 248.00

16 Labour wrought and put up in position flyproof wire gauge shutters for doors, windowsand ventilators sq.m 576.00

17 Labour wrought and put up for providing teakwood weld mesh screen with frames 3"x3"(0.075mx0.075m) sq.m 805.00

18 Labour charges for fixing aluminium doors,windows and ventilators sq.m 549.00

Schedule Rates for


307

Schedule Rates for


34 Breaking metalsi. Labour charges for breaking 40mm metal

from departmental blasted stones Cu.m 305.00ii. Labour charges for breaking 20mm metal

from departmental blasted stones Cu.m 456.00iii. Labour charges for breaking 50mm metal from

departmental blasted stones Cu.m 182.8035 Cement Mortari. Grinding Mortar (Special Grinding lime) Cu.m 277.00ii. Grinding Mortar (Ordinary Grinding lime) Cu.m 211.00iii. Mixing Mortar – Cement by manual Cu.m 87.00iv. Mixing Mortar- Cement by Machine Mixing Cu.m 115.0036 Metal & Iron worksi. Petty iron work for truss, straps etc.

(Wrought & fixed) labour only Kg 41.60ii. Iron works for trusses & record racks (labour only) kg 38.40iii. Fixing in position mild steel grills for windows,

ventilators, etc. Kg 24.00iv. Fixing MS rods round/square for windows Kg 22.30v. Fixing iron bars in windows and ventilators Kg 22.3037 Conveyance of excavated earth from the

narrow street (width less than 3.75m) to stockyard at nearest place (up to a lead of 5.00Km)including Head load charges from 10 metersto 100 meters and conveyance charges. Cum 105.80

3838 Re-Conveyance of earth from the stock yard

to the narrow street (width less than 3.75m)for refilling the trenches after laying the pipeline (up to a lead of 5.00Km) including Headload charges from 10 meters to 100 metersand conveyance charges. Cum 105.80

39 Disposal of surplus earth including loading andconveyance within a distance of 5 km (basiccost of earth is zero) including loading chargesand Conveyance Charges of 5 kms distance. Cum 90.00

40 Lighting arrangements (maintenanceworks) with genset :Hire charges for portable Genset 1.00 KVA with2 Nos. of 150W flood light including all incidentalcharges, transportation, crew charges and fuelcharges etc., complete. Per day 2050.00

308

41 Hire charges for deploying earth movingmachinery (JCB/Poclain) for earthworkincluding diesel, oil and labour charges etc.,complete.

a JCB Per Hour 700.00b Poclain Per Hour 2050.00

42 Supply delivery of natural Pebbles filter mediafor Filter bed operation & sedimentary borewell of spherical in shape and allow evendistribution in support bed with good flow. Themedia should be double washed, screened, kilndried and classified into various sizes to meetspecification including all incidental charges,conveyance, loading & unloading etc., asdirected by the TWAD Board officers.

a Size : 5 mm to 20mm Cum 4095.00b Size : 20 mm to 70 mm Cum 3745.00

Schedule Rates for


309

i Barricading work (Where, there is less traffic areasand broader roads etc.) for laying of pipe line usingcasurina poles at 1.50m center to center (8cm to10cm dia and 1.80m height) vertical with horizontalpoles in three rows including painting the verticalpoles in the road facing sides with ready mix paint,tying the vertical and horizontal poles with coir ropeincluding fixing charges and fixing 75mm dia reflectorsincluding earth work excavation for fixing verticalposts and finally removing and stacking the materialssafely for further use etc., complete and as directedby TWAD Board officers.

ii Barricading work (Where the lines are in narrow widthof municipality area, busy streets like Market, Bus-stand and in the Highways etc.) for laying of pipeline using casurina poles at 1.50m center to center(8cm to 10cm dia. and 1.80m height) vertical withhorizontal poles in two rows, painting the verticalpoles in the road facing sides with ready mix paint,tying the vertical and horizontal poles with coir ropeincluding supplying, delivery and fixing of GI sheet(0.90m x 0.8mm thick) in the horizontal poles andfixing 75mm dia. reflectors including earth workexcavation for fixing vertical posts and finallyremoving and stacking the materials safely for furtheruse etc., complete and as directed by TWAD Boardofficers.

S. TWADNo. Description Unit Rate/m

RM Rs.47.00

RM Rs.89.00

43. BARRICADING FOR PIPELINE WORKS FOR THE WSS / UGSS WORKS

310


44. SHORING AND STRUTTING FOR THE WSS / UGSS WORKS

Shoring, and strutting with sheet piles of size width400 mm x height of 3m x thickness of 9mm as per IS2314-1986 by driving on both sides of the trenchfrom Ground Level up to the required depth andconnecting the above sheet piles by horizontalstrutting with sheet piles at an interval of 1.0m,fixing the sheet piles by connecting the horizontalstrutting with casurina poles of 8cm to 10cm dia.at 1.50m interval and including removing the sheetpiles after the pipelines are laid, jointed, tested,and stacking it safely for other uses. It includesthe cost of sheet piles and casurina poles includinglabour charges for erecting the sheet piles, drivingthe sheet piles, removing the sheet piles, fixingCasurina poles, etc., complete and all other incidentalcharges for the depths (i) 0-3mts.,(ii) 0-4mts.,(iii)0-5mts., (iv) 0-6mts.,(v) 0-7mts. and (vi) 0-8mts.

a 0 to 3 m RM 2381.28b 0 to 4 m RM 3224.45c 0 to 5 m RM 4086.61d 0 to 6 m RM 4931.50e 0 to 7 m RM 5791.94f 0 to 8 m RM 6741.90

311


45. RATES FOR TRENCHLESS TECHNOLOGY FOR PIPE LAYING WORK IN RAILWAY/NHAI/SH/NH CROSSINGS.

i Excavating of driving pit and receiving pit of size3.00m (length) x 3.50m (breadth), upto 5m depthin all soil strata including shoring and strutting using6mm tk MS Plate of size 3.50m x 3.50m usable for20 operations and providing 16mm thickness MSplate of size 3.00m x 3.50m with 100mm x100mm x12mm angles of 4m length for holding the MS platesfor Thrust arrangements to receive the impacts duringpushing operation of encasing pipe. Lowering thefollowing size of MS encasing pipe by usingContractor’s crane and machineries and jointing MSpipes by welding, across the National Highways/State Highways/ Railways/Canal crossing etc anddriving the horizontal bore by pushing / jackingmethod (trenchless technology method) usingcontractor’s machineries such as cranes, jacks,jacking materials, generator, welding machineries,compressor, jack hammer and other equipments etc.without interfering and causing any hindrance tothe movement of traffic or any other vehicles,without any disturbances to the railway/road/canalformation etc. including bailing / pumping of waterwhere ever necessary without affecting anyinstallation like water supply pipeline/telephonecable, electric cables etc. passing nearby area andscooping the earth inside the pipes and pit anddepositing the surplus earth in a convenient placeand leveling the site after completion of entire workas directed by TWAD Engineers. The rate includesthe cost of driving pit, thrust bed/wall and receivingpit to the depth of om to 5m excluding the cost ofMS pipes.

a For 200mm dia MS encasing pipe for various thickness RM 8440.00b For 250mm dia MS encasing pipe for various thickness RM 8530.00c For 300mm dia MS encasing pipe for various thickness RM 8620.00ii Excavating of driving pit and receiving pit of size

3.00m (length) x 3.50m (breadth), depth upto 5min all soil strata including shoring and strutting using6mm tk MS Plate of size 3.50m x 3.50m usable for15 operations and providing 16mm thickness MS

312

plate of size 3.00m x 3.50m with 100mm x100mm x12mm angles of 4m length for holding the MS platesfor Thrust arrangements to receive the impacts duringpushing operation of encasing pipe. Lowering thefollowing size of MS encasing pipe by usingContractor’s crane and machineries and jointing MSpipes by welding, across the National Highways/State Highways/ Railways/Canal crossing etc anddriving the horizontal bore by pushing / jackingmethod (trenchless technology method) usingcontractor’s machineries such as cranes, jacks,jacking materials, generator, welding machineries,compressor, jack hammer and other equipments etc.without interfering and causing any hindrance tothe movement of traffic or any other vehicles,without any disturbances to the railway/road/canalformation etc. including bailing / pumping of waterwhere ever necessary without affecting anyinstallation like water supply pipeline/telephonecable, electric cables etc. passing nearby area andscooping the earth inside the pipes and pit anddepositing the surplus earth in a convenient placeand leveling the site after completion of entire workas directed by TWAD Engineers. The rate includesthe cost of driving pit, thrust bed/wall and receivingpit to the depth of om to 5m excluding the cost ofMS pipes.

a For 350mm dia MS encasing pipe for various thickness RM 9880.00b For 400mm dia MS encasing pipe for various thickness RM 10220.00c For 450mm dia MS encasing pipe for various thickness RM 10460.00d For 500mm dia MS encasing pipe for various thickness RM 10630.00e For 600mm dia MS encasing pipe for various thickness RM 10950.00f For 700mm dia MS encasing pipe for various thickness RM 11850.00g For 800mm dia MS encasing pipe for various thickness RM 12170.00h For 900mm dia MS encasing pipe for various thickness RM 12460.00iii Excavating of driving pit and receiving pit of size

3.00m (length) x 3.50m (breadth), depth upto 5min all soil strata including shoring and strutting using6mm tk MS Plate of size 3.50m x 3.50m usable for10 operations and providing 16mm thickness MSplate of size 3.00m x 3.50m with 100mm x100mm x12mm angles of 4m length for holding the MS platesfor Thrust arrangements to receive the impacts during


313

pushing operation of encasing pipe. Lowering thefollowing size of MS encasing pipe by usingContractor’s crane and machineries and jointing MSpipes by welding, across the National Highways/State Highways/ Railways/Canal crossing etc anddriving the horizontal bore by pushing / jackingmethod (trenchless technology method) usingcontractor’s machineries such as cranes, jacks,jacking materials, generator, welding machineries,compressor, jack hammer and other equipments etc.without interfering and causing any hindrance tothe movement of traffic or any other vehicles,without any disturbances to the railway/road/canalformation etc. including bailing / pumping of waterwhere ever necessary without affecting anyinstallation like water supply pipeline/telephonecable, electric cables etc. passing nearby area andscooping the earth inside the pipes and pit anddepositing the surplus earth in a convenient placeand leveling the site after completion of entire workas directed by TWAD Engineers. The rate includesthe cost of driving pit, thrust bed/wall and receivingpit to the depth of om to 5m excluding the cost ofMS pipes.

a For 1000mm dia MS encasing pipe for various thickness RM 13820.00b For 1050mm dia MS encasing pipe for various thickness RM 14140.00c For 1100mm dia MS encasing pipe for various thickness RM 15240.00d For 1200mm dia MS encasing pipe for various thickness RM 16410.00e For 1400mm dia MS encasing pipe for various thickness RM 17700.00f For 1600mm dia MS encasing pipe for various thickness RM 19030.00g For 1800mm dia MS encasing pipe for various thickness RM 20540.00h For 2000mm dia MS encasing pipe for various thickness RM 22090.00i For 2200mm dia MS encasing pipe for various thickness RM 24590.00


314

i. Replacement of Underground Utilities (GI Pipe)damaged during earthwork excavations for pipelaying works including cost of additional earthworkexcavation in all soil strata, including BT/CC roadcutting, removal of slushy soil and replacing thepipeline with sound pipe, including supply anddelivery of GI pipes, coupler, Union, jointing materialsand required specials, cutting, threading, conveying, laying, jointing and cost of refilling for the additionalearthwork etc complete and as directed by theTWAD board officers.

a. 15mm Dia GI Pipe 1RM 428.33b. 20mm Dia GI Pipe 1RM 463.00c. 25mm Dia GI Pipe 1RM 557.67d. 32mm Dia GI Pipe 1RM 652.67e. 40mm Dia GI Pipe 1RM 739.33f. 50mm Dia GI Pipe 1RM 920.67g. 65mm Dia GI Pipe 1RM 1390.50h. 80mm Dia GI Pipe 1RM 1679.83i. 100mm Dia GI Pipe 1RM 2345.83j. 125mm Dia GI Pipe 1RM 3139.83ii. Replacement of Underground Utilities (PVC Pipe)

damaged during earthwork excavation for pipe layingworks including cost of additional earthworkexcavation in all soil strata, including BT/CC roadcutting, removal of slushy soil and replacing thepipeline with sound pipe, including supply anddelivery of PVC pipes, couplers, jointing materialsand required specials, cutting, conveying , laying,jointing and cost of refilling for the additionalearthwork etc complete and as directed by theTWAD board officers.

a. 15mm Dia PVC Pipe (10 KSC) 1RM 225.52b. 20mm Dia PVC Pipe (10 KSC) 1RM 233.32c. 25mm Dia PVC Pipe (10 KSC) 1RM 249.45d. 32mm Dia PVC Pipe (10 KSC) 1RM 269.35e. 40mm Dia PVC Pipe (10 KSC) 1RM 304.55f. 50mm Dia PVC Pipe (10KSC) 1RM 291.52


46. REPLACEMENT OF UNDER GROUND UTILITIES (HSC PIPES, DISTRIBUTIONSYSTEM & PUMPING MAIN PIPES, Etc.)

315

g. 63mm Dia PVC Pipe (10KSC) 1RM 344.58h. 75mm Dia PVC Pipe (10KSC) 1RM 390.08i. 90mm Dia PVC Pipe (10KSC) 1RM 483.92j. 110mm Dia PVC Pipe (10KSC) 1RM 696.00k. 140mm Dia PVC Pipe (10KSC) 1RM 1004.00l. 160mm Dia PVC Pipe (10KSC) 1RM 1213.67m. 180mm Dia PVC Pipe (10KSC) 1RM 1503.82n. 200mm Dia PVC Pipe (10KSC) 1RM 1949.48

Replacement of Underground Utilities (PVC Pipe)damaged during earthwork excavation for pipe layingworks including cost of additional earthworkexcavation in all soil strata, including BT/CC roadcutting, removal of slushy soil and replacing thepipeline with sound pipe, including supply anddelivery of PVC pipes, couplers, jointing materialsand required specials, cutting, conveying , laying,jointing and cost of refilling for the additionalearthwork etc complete and as directed by theTWAD board officers.

a. 50mm Dia PVC Pipe (6KSC) 1RM 258.25b. 63mm Dia PVC Pipe (6KSC) 1RM 293.37c. 75mm Dia PVC Pipe (6KSC) 1RM 327.58d. 90mm Dia PVC Pipe (6KSC) 1RM 381.25e. 110mm Dia PVC Pipe (6KSC) 1RM 476.33f. 140mm Dia PVC Pipe (6KSC) 1RM 706.67g. 160mm Dia PVC Pipe (6KSC) 1RM 857.67h. 180mm Dia PVC Pipe (6KSC) 1RM 1079.82i. 200mm Dia PVC Pipe (6KSC) 1RM 1390.48iv Replacement of Underground Utilities (PVC Pipe)

damaged during earthwork excavation for pipe layingworks including cost of additional earthworkexcavation in all soil strata, including BT/CC roadcutting, removal of slushy soil and replacing thepipeline with sound pipe, including supply anddelivery of PVC pipes, couplers, jointing materialsand required specials, cutting, conveying , laying,jointing and cost of refilling for the additionalearthwork etc complete and as directed by theTWAD board officers.


316

a. 63mm Dia PVC Pipe (4KSC ) 1RM 266.92b. 75mm Dia PVC Pipe (4KSC) 1RM 291.25c. 90mm Dia PVC Pipe (4KSC) 1RM 326.58d. 110mm Dia PVC Pipe (4KSC) 1RM 449.50e. 140mm Dia PVC Pipe (4KSC) 1RM 572.33f. 160mm Dia PVC Pipe (4KSC) 1RM 679.67g. 180mm Dia PVC Pipe (4KSC) 1RM 867.82h. 200mm Dia PVC Pipe (4KSC) 1RM 1070.82v Replacement of Underground Utilities (AC Pipe)

damaged during earthwork excavation for pipe layingworks including cost of additional earthworkexcavation in all soil strata, including BT/CC roadcutting, removal of slushy soil and replacing thepipeline with next available higher size PVC pipe,including supply and delivery of PVC pipes, couplers,jointing materials and required specials, cutting,conveying , laying, jointing and cost of refilling forthe additional earthwork etc complete and asdirected by the TWAD board officers.

a. 80mm Dia AC Pipe 1RM 650.04b. 100mm Dia AC Pipe 1RM 801.68c. 125mm Dia AC Pipe 1RM 1147.80vi Replacement of Underground Utilities (AC Pipe)

damaged during Earthwork excavation for pipe layingworks including cost of additional earthworkexcavation in all soil strata, including BT/CC roadcutting , removal of slushy soil and replacing thepipeline with sound DI s/s pipe, including supplyand delivery of DI s/s pipes, D/S collars, jointingmaterials and required specials, cutting, conveying, laying, jointing and cost of refilling for the additionalearthwork etc complete and as directed by theTWAD board officers.

a. 150mm Dia AC Pipe 1RM 2638.23b. 200mm Dia AC Pipe 1RM 3277.04c. 250mm Dia AC Pipe 1RM 3995.68d. 300mm Dia AC Pipe 1RM 4266.22e. 350mm Dia AC Pipe 1RM 5412.43f. 400mm Dia AC Pipe 1RM 6545.21


317

vii Replacement of Underground Utilities (HDPE Pipes)damaged during Earthwork excavations for pipelaying works including cost of additional earthworkexcavation in all soils, including BT cutting, CCroads , removal of slushy soil and replacing thepipeline with sound pipe, including supply and deliveryof HDPE pipes, couplers, jointing materials andrequired specials, cutting, threading, conveying ,laying, jointing and cost of refilling for the additionalearthwork etc complete and as directed by theTWAD board officers.

a. 50mm Dia HDPE Pipe 1RM 372.33b. 63mm Dia HDPE Pipe 1RM 434.65c. 75mm Dia HDPE Pipe 1RM 503.98d. 90mm Dia HDPE Pipe 1RM 594.47e. 110mm Dia HDPE Pipe 1RM 803.10f. 125mm Dia HDPE Pipe 1RM 926.81g. 140mm Dia HDPE Pipe 1RM 1060.51h. 160mm Dia HDPE Pipe 1RM 1254.39i. 200mm Dia HDPE Pipe 1RM 1745.22


Documents

STANDARD SCHEDULE OF RATES FOR THE YEAR 2020-2021