Stealth AA965Vertical Machining Center

Specifications

All specifications are subject to change without prior noticeVerification of technical changes may be confirmed after receipt of order

Stealth AA965 Page 2

Machine Specifications (All Models, Unless Otherwise Indicated):

Stroke Unit Specifications

X Axis Travel (AA965) mm (in) 900 (35.4)

Y Axis Travel mm (in) 650 (25.6)

Z Axis Travel mm (in) 600 (23.6)

Distance from Spindle Nose to Table Top mm (in) 125 - 725 (4.9 - 28.5)

Distance from Spindle Center to Column mm (in) 650 (25.6)

Table Unit Specifications

Table Size: X Direction (AA965) mm (in) 1,100 (43.3)

Table Size: Y Direction mm (in) 650 (25.6)

Table Load Capacity (AA965) kg (lb) 900 (1,985)

Table T-Slot Size: Width x Distance x Number mm (in) 18 x 125 x 5 (0.71 x 4.92 x 5)

Table Height From Plant Floor mm (in) 900 (35.4)

Designed and built by Wele Mechatronic in Taiwan, this machining center is sold and serviced exclusively by JTEKT Toyoda Americas Corporation and our exclusive representatives in the Americas.

JTEKT Toyoda Americas Corp. recommends the use of only genuine BIG-PLUS® tooling (if applicable).The BIG-PLUS®

system is licensed only to certain tool holder manufacturers, please verify the authenticity of any holders used in the spindle. Failure to use certified BIG-PLUS® certified tooling (if applicable) may void your warranty.

SpindleCat # 40 Taper Geared Head

Type 2 Speed Gearbox

Max RPM 8,000Power Nm Kw (HP) [cont. / peak 30 min] 11 / 15 (15 / 20)

Max Torque Nm (Ft Lbs) 380 (282)Front Bearing Diameter mm (in) 75 (2.95)

Cat # 50 Taper Geared Head

Type 2 Speed Gearbox

Max RPM 6,000Power Nm Kw (HP) [cont. / peak 30 min] 15 / 18.5 (20 / 25)

Max Torque Nm (Ft Lbs) 460 (339)Front Bearing Diameter mm (in) 85 (3.35)

Cat # 40 Taper Direct Driven

Type Direct DriveMax RPM 12,000Power Nm Kw (HP) [cont. / peak 30 min / peak 15 min]

15/ 18.5/ 22 (20/ 25 / 30)

Max Torque Nm (Ft Lbs) 125 (92)Front Bearing Diameter mm (in) 70 (2.75)

Note: Machine is 220V / 3 Phase / 60 Hz. Any other voltage requires a transformer (not supplied as std.)* Dimensions are approximate, please verify upon ordering

Stealth AA965 Page 3

Feed Rates Unit SpecificationsRapid Feedrate (X and Y Axes) m/min (ipm) 30 (1,181)Rapid Feedrate (Z Axis) m/min (ipm) 24 (945)Maximum Cutting Feedrate m/min (ipm) 24 (945)

Accuracy (JIS) Unit SpecificationsPositioning Accuracy mm (in) ±.005 (±.0002)Repeatability mm (in) ±.003 (±.0001)

Coolant System Unit SpecificationsCoolant Tank Capacity gal 113.5Flood Coolant (Gallons per Minute) gal 20CTS Preparation Only Max PSI Rotary Union: 1,000 PSI Capable

ATC - 24 Tool "Drum" Type With "S" Cam Drive Unit SpecificationsTool Magazine Capacity - CT40 number 24Tool Magazine Capacity - CT50 number 24Maximum Tool Diameter / Tool in Adjacent Pocket -CT40 mm (in) 76 (2.99)Maximum Tool Diameter / Tool in Adjacent Pocket -CT50 mm (in) 127 (5.0)Maximum Tool Diameter / Adjacent Pocket Empty -CT40 mm (in) 127 (5.0)Maximum Tool Diameter / Adjacent Pocket Empty -CT50 mm (in) 229 (9.0)Maximum Tool Length from Gage Line - CT40 mm (in) 250 (9.8)Maximum Tool Length from Gage Line - CT50 mm (in) 300 (11.8)Maximum Tool Weight - CT40 kg (lb) 7 (15.4)Maximum Tool Weight - CT50 kg (lb) 15 (33)Tool Taper type CAT40, CAT50Pull Stud type ANSI CAT40, ANSI CAT50Tool Change Time: Tool to Tool sec 3Tool Selection type RandomTool Access type Bi-directional

Control Unit SpecificationsControl Type type Fanuc Oi M-D Package A

Utilities Unit SpecificationsPower Required v (kVA) 3 Phase ±10% 220 (35)Air Pressure psi 100Power Supply Frequency Hz 50 / 60Control Voltage volt 24

Stealth AA965 Page 4

Chip Blaster JV-40 High Pressure Automatic Variable Volume Coolant System 1,000 PSI, 10.5 Gpm, 100 Gallon Tank Standard, Single Bag Filtration Standard

Chip Blaster J-30 High Pressure Fixed Flow Coolant System 1,000 PSI, 8 Gpm, 100 Gallon Tank Standard, Single Bag Filtration Standard

Chip Blaster D-30-70 High Pressure Fixed Flow Coolant System 1,000 PSI, 8 Gpm, Tank Not Included, Dual Cartridge Filtration Standard

Chip Blaster D-30-35 Medium Pressure Coolant System 300 PSI, Tank Not Included Unit Pricing Includes Plumbing, Electrical Installation Kit and Installation Guide

CTS Unit Pricing Includes Plumbing, Electrical Installation Kit and Installation Guide,Installation is Not Included

4th Axis Stealth Kit Includes: Power and I/O Cables to the Enclosure Roof, Mil Spec Bulkhead Connectors with Sheet Metal Plate, Relay, Amp Busbar, 10mm Air Pipe, and Air Connectors. Kit Does Not Include Axis Drive or Cables From Bulkhead to Table.

200mm (7.8”) column riser, includes raised sheet metal, increases minimum spindle nose to table top distance from 125mm (4.9”) to 325mm (12.8”)

400mm (15.7”) column riser, includes raised sheet metal, increases minimum spindle nose to table top distance from 125mm (4.9”) to 525mm (20.67”)

AICC Contour Control II PCB Fast Ethernet/Data Server,1 Gig Memory Card, Operator's Manual, Ethernet Function Software, Fast Data Server Function Software, Installation by Fanuc Technician after Completion of Initial Machine Installation. Addition of this option is not to be confused with HPCC, as it will not change the standard block look ahead of 40. This option will allow Stealth users to connect their machine to Ethernet for DNC use via FTP, or expand at machine accessibility of programs / program storage in addition to the memory card slot already provided on the operator's pendant.

Increase from 40 Block Look Ahead to 200 Block Look Ahead

Multi Step Skip Function Required when both a Spindle Probe and Tool Measurement Device are installed

Optional Equipment – Must be factory installed

Stealth AA965 Page 5

Miscellaneous

Price is F.O.B. Port of Entry

Toyoda’s responsibility ceases when delivery is made to the carrier.

Any claim for loss and/or damage must be made by the purchaser against the carrier.

One (1) Year Parts and Labor Warranty on Machine and Control

Machine Training, Set-Up and Warranty Labor

Via Toyoda or Authorized Distributor

Place of Shipment

Port of Entry, unless otherwise stated

Time of Quote Validity

Ninety (90) Days, unless otherwise stated

Payment Terms

Ten (10%) Percent with Purchase Order

Eighty (80%) Percent Upon Shipment

Ten (10%) Percent Thirty (30) Days from Shipment

Stealth AA965 Page 6

Specifications of Fanuc Oi MD Control (Stealth Package) Function Description10.4" LCDAbsolute / Increment CommandAddition of Custom Macro Common Variables #100～#199, #500～#999Addition of Workpiece Coordinate System PairAI Nano CC Look-Ahead 40 bps (AI HPCC is not Available)Alarm DisplayAlarm History DisplayAutomatic Corner OverrideAutomatic Power Off M30Background EditingBacklash CompensationCanned Cycles G74, G76, G80, G81, G84~G89Canned Cycles for Drilling G73, G83Circular Interpolation G02, G03Conical / Spiral InterpolationControllable Axes 4 AxesCoordinate System Rotation G68, G69Custom Macro BCutting Feedrate CommandCutting Feedrate Override 0, 10%, 20%, 30%, …,150%Cylindrical InterpolationDecimal Point Programming / Pocket Calc Type Decimal Point ProgrammingDry RunDwell G04Emergency StopEthernet Interface (RJ45)Exact Stop G09Exact Stop Mode G61Extend Program EditFANUC Semi-Operator PanelFeedrate Speed SettingG Code Program Mirror Function G50.1 / G51.1Graphic DisplayHandle InterruptionHandle Wheel Feedrate 1 Handle WheelHandle Wheel Override Override X1, X10, X100Helical InterpolationHRV3 Control HRV 3InterpolationInterpolation Pitch Error Compensation Standard EquipmentLeast Programmable Increment 0.001mm / 0.0001" / 0.001ºLimit Check Before MovementLinear Acceleration/Deceleration after Cutting FeedLinear Interpolation G01Machine LockManual Reference Position Return G28Maximum Command Value ± 99999.999M-Code Blush M07

Stealth AA965 Page 7

Specifications of Fanuc Oi MD Control (Stealth Package) Function DescriptionMetric / Inches Conversion G20, G21MST FunctionOperation History DisplayOperator Message History DisplayOptional Chamfering / Corner ROptional Single Block SkipPC MCIA Memory Card Slot On CNC PendantPlane Selection G17, G18, G19PlaybackPolar Coordinate Command G15, G16Program Number Display O4 digitsProgram RestartProgram Single Block Number N5 DigitsProgram Start / Movement Hold M00, M01Program Stop / Program End M02, M30Program Storage 1,280 M (512 kB)Programmable Data Input G10Rapid Movement Percentage F0, 25%, 50%, 100%Rapid Positioning G00Rapid Traverse Bell-Shaped Acceleration / DecelerationRegistered Program Number 400 PcsRemote DiagnosticRigid Tapping M29RS232 InterfaceRun Hour and Parts Count DisplayScalingSimultaneous Axes 4 AxesSingle BlockSingle Direction Positioning G60Soft Limit SettingSpindle Positioning M19Spindle Speed Override 50%, 60%, 70%, …, 120%Sub-Program Call 4 LevelsTool Offset 400 SetsTool Offset Memory CTool Offset Value Counter InputTool Positioning Offset G45～G48Tool Radius Compensation C G40, G41, G42Workpiece Coordinate System G54～G59Z Axis Lock

Stealth AA965 Page 8

Included with this Model:

1.8.4” Color LCD Display

2.Chip Wash Down Coolant

3.Chip Wash Gun

4.Conversational FANUC Manual Guide 0i

5.Coolant System including tank & pumps

6.Plumbing for Coolant Through Spindle up to 70 bar (1000 PSI)

7.Dual Chip Auger Each Side of Table

8.Full Enclosure Splash Guard (Height up to 2,000 mm)

9.20 hp Spindle Motor

10.Hand Tool Box

11.Helical Interpolation

12.Lift Up Type Hinged Bent Chip Conveyor (47“ drop height)

13.Manual Pulse Generator (Hand Wheel)

14.Operation and Maintenance Manual, Fanuc Manuals

15.Programmable Air Blast

16.Rigid Tapping

17.RS-232 Interface and Ethernet RJ45 Interface

18.Spindle Oil Cooler

19.24 Pocket ATC (#40 or #50 taper)

20.Three (3) Tier Status / Alarm Lamp

21. Fixed & Adjustable Work Light

Stealth AA965 Page 9

Spindles

Power& Torque CAT40 or CAT50 Geared Head

Stealth AA1565 Page 10

Spindles

Power& Torque CAT50 Geared Head

Stealth AA965 Page 11

Spindles

Power & Torque CAT40 12,000 Direct Driven (Option)

Stealth AA965 Page 12

Retention Knob & Tool Assembly CAT40

Retention Knob & Tool Assembly CAT50

Stealth AA965 Page 13

Table Dimensions

Work Envelope

Stealth AA965 Page 14

Floor Space Requirement