Store kit setup guide - iZettle€¦ · • Your iZettle Pro account login details (for login to the app) • Your iZettle account login details (for activating payments) 6 iZettle

Store kit setup guide

V1.1

2

Table of contents

GETTING STARTEDAbout this guide 4

Physical requirements 5

THERMAL RECEIPT PRINTERS

TSP654II - Ethernet Identifying the ports 9

Wiring diagram 10

Inserting the receipt paper 11

Setting up the printer within iZettle Pro 12

TSP654II - Bluetooth Identifying the ports 13

Wiring diagram 14

Pairing the printer 15



TSP143III - Lightning cable Identifying the ports 18

Wiring diagram 19



IZETTLE READER

Pairing the reader 6

Setting up the reader within IZettle Pro 7

Using the reader with iZettle Pro 8

3

KITCHEN PRINTER

SP700 Identifying the ports 22

Wiring diagram 23

inserting the receipt paper 24

Inserting the ink cartridge 25


BARCODE SCANNER

Socket Mobile Companion App 27

Setting up the scanner within iZettle Pro 28

4

About this guide

This guide will help you set up your Store Kit hardware to work with iZettle Pro.

SPECIFICALLY COVERING SETUP OF:

• iZettle Reader• TSP654II Ethernet printer• TSP654II Bluetooth printer• TSP143III Lightning cable printer• SP700 Kitchen Printer• Socket Mobile Barcode Scanner As well as the basic physical and software requirementsnecessary for setup of your Store Kit.

5

Dimensions (mm) (w) (l) (h)

iZettle Reader Charge Dock

85 150 100

TSP654 Printer 142 203.5 132

SP700 Kitchen Printer

160 245 152

Cash Drawer & Wrap 340 370 110

Cash Drawer 335 335 100

Important! Before getting started

YOU WILL NEED TO MAKE SURE YOU HAVE THE FOLLOWING READY:

Physical Requirements

• A shelf or countertop space of (w) 340mm x (l) 370mm (h) 110mm height per drawer

• One standard power socket for each Printer, each iPad and each Card Reader

• One RJ45 CAT5 (ethernet) cable for each Ethernet printer you will be connecting into your network

• One USB adaptor for each card reader (Minimum 1A 5V)

IF PLACING YOUR CASH DRAWER UNDERNEATH THE COUNTER we advise having a 25mm hole in the counter to run cables through.

Software Requirements

• An Apple iCloud account (for login on the iPad)

• Your iZettle Pro account login details (for login to the app)

• Your iZettle account login details (for activating payments)

6

iZettle Reader

PAIRING THE READER

Ensure the reader displays thefollowing, indicating it is ready to be set up within Pro.

Once connected to the readeryou will be prompt to compareand confirm the number on thescreen matches that on the device.

Once paired, it should display the following information, indicating it is ready to be used to take payments.

7

Setting up the reader within iZettle Pro

You should now see a list ofavailable iZettle Reader 2 devices ready to be set up. Switch on your Reader.

When the reader is powered on,you should be presented with anumber, like the above.

With the reader powered on, itshould show under Detected Card Readers. Tap on the reader that shows on this list.

8

Using the reader with iZettle Pro

If you tap on a product and select Pay you will come to the Payment Due screen.

Select Pay with iZettle on the left, this will allow us to check the reader connection is working fine.

If the firmware has been updated you should be prompted with the following screen, simply press the X on the reader to refuse the Tip.

You should now be given the final screen prompting to insert or swipe a card.

Do not do so, but select Cancel. The reader is now set up to take payments.

9

Please connect the Ethernet cable coming from your router into the LAN/Ethernet port shown below.

If you have a Cash Drawer this would connect into the DK (Drawer Kick) port also shown above.

Once you have these connected and the printer plugged into an available mains connection, switch it on using the IO switch on the side of the printer.

TSP654II - Receipt printer - Ethernet

Reset button

LAN/Ethernet

DK

Power

10

TSP654II

Broadband router

Ethernet cable

Cash drawer

TSP654II - Receipt printer - Ethernet

11

Insert the roll, by popping the lid open using the latch on the right hand side, with the outer shiny side of the paper facing downwards and the inside of the roll facing you, as shown above.

Once you have done this, pull out a little bit of receipt paper, so that when you have closed the latch the automatic feed and cut takes place, preventing blockages and indicating the printer is ready to be set up in the iZettle Pro app.

Inserting the receipt paper - TSP654II Ethernet

12

Setting up TSP654II Ethernet within Pro

When in the sales screen tap on the small cog at the top left.

Select Printers - You should now see an unnamed printer appear.

If you tap on this you can now go ahead to set it up.

Switch on Standard Receipts and also Cash Drawer. If you would like to set the printer up to also print “station” receipts you can do this here.

You can also rename the printer, which is recommended especially if you use more than 1 printer.

13

TSP654II - Receipt printer - Bluetooth



Once you have these connected and the printer plugged into an available mains connection, switch it on using the IO switch on the side of the printer

Reset button

Status LED

Pair buttonDK Power

14

iPad with iZettle Pro TSP654II

Cash drawer

TSP654II - Receipt printer - Bluetooth

15

Pairing the TSP654II to an iPad via Bluetooth

On the rear of this printer the LED at the back will be solid green, indicating no activity.

Press and hold the PAIR button for 5 seconds and when you let go the green LED should blink

If you go into Settings on your iPad then tap on Bluetooth, you should see Star Micronics appear in Other Devices. Tap on this to start pairing

Once fully paired the LED at the back of the printer should now turn to solid blue, indicating it has been connected with the iPad and ready to be used.

16

Inserting the receipt paper - TSP654II Bluetooth

Insert the roll, by popping the lid open using the latch on the right hand side, with the outer shiny side of the paper facing downwards and the inside of the roll facing you, as shown above

Once you have done this, pull out a little bit of receipt paper, so that when you have closed the latch the automatic feed and cut takes place, preventing blockages and indicating the printer is ready to be set up in the App

17

Setting up TSP654II within iZettle Pro





You can also rename the printer, which is recommended especially if you use more than 1 printer.

18

TSP654II - Receipt printer - Lightning cable

Please connect the charging cable that comes with your iPad into the USB port shown below.



USB Port

DK Port Power

19

TSP143III

Cash drawer

iPad with iZettle Pro

Lightning cable

TSP143III - Lightning cable printer

20

Inserting the receipt paper - TSP143III

Insert the roll, by popping the lid open using the latch on the right hand side, with the outer shiny side of the paper facing downwards and the inside of the roll facing you, as shown above


21

Setting up TSP143III within Pro





You can also rename the printer, which is recommended especially if you use more than 1 printer

22

SP700 - Kitchen Printer


If you have a kitchen buzzer (Sold separately) this would connect into the Buzzer port also shown above.


BuzzerLAN/Ethernet

Reset Button

Power

23

SP700

Broadband router

Ethernet cable

RJ45 / Cat5 Socket

Kitchen buzzer

SP700 - Kitchen Printer

24

Insert the roll, by popping the rear lid open using the latch on the right hand side, with the outer side of the paper facing downwards and the inside of the roll facing you, as shown above


Inserting the receipt paper - SP700

25

Open the latch and slot the cartridge in with the ribbon tension knob to the right hand side (See highlighted area)

When slotting the ribbon in, make sure you place the ribbon between the paper and the impact mechanism, shown above

Inserting the ink cartridge - SP700

26

Setting up kitchen printer SP700 within Pro




Switch on Kitchen Receipts and also Cash Drawer if you have a buzzer.

If you would also like to set the printer up to also print “station” receipts you can do this here. You can also rename the printer, which is recommended

27

Socket Mobile - barcode scanner

Setting up the Barcode Scanner requires a different process than most Bluetooth devices, that pairing with the iPad is the last thing that should be done.

Out of the box, the scanner is set up in “Keyboard” mode, meaning that we need to assign the correct mode first before we pair. We can download the Socket Mobile Companion App to make this process easier.

Download the Socket Mobile Companion App here or scan the QR code below with your iPad.

https://itunes.apple.com/gb/app/socket-mobile-companion/id1175638950?mt=8

https://itunes.apple.com/gb/app/socket-mobile-companion/id1175638950?mt=8

28

Setting up the barcode scanner within iZettle Pro

Once you open Pro we need to allow the integration for this Scanner.

Tap on Integrations and switch on Socket Mobile Scanner.

Once you have enabled integration close and re-open iZettle Pro, you should then hear the scanner beep and see the green notification bar advising Barcode Scanner Connected.

Test the scanner work by going into Settings - Products and selecting a product to edit.

Then tap on Barcode or SKU field and use the scanner to scan a barcode.

Documents

Store kit setup guide - iZettle€¦ · • Your iZettle Pro account login details (for login to the app) • Your iZettle account login details (for activating payments) 6 iZettle