Street Design · specified if the location or project requires it. All mild steel fixings will be bright zinc plated, and all stainless steel fixings will be A2 (grade 304). A4 (grade

STUDIO seating

UK street furniture designers & manufacturers

Street Designestablished in 1986

Street Design Limited Contact us

01509 81533501509 [email protected]

Telephone:Fax:Email:Web site:

Unit 47, Hayhill Industrial EstateBarrow upon SoarLeicestershireLE12 8LD

As UK based, designers and manufacturers, Street Design can manufacture and supplyStudio seating to suit your specific requirements.

Straight benches can be manufactured from a range of material and finishes.

Choose from a range of accessories to ensure that the Studio seating is manufactured to suit your specific scheme.

Studio bench product details

Studio material finishes

Studio accessories

Studio technical specification

Studio bench in natural finish FSC iroko hardwood with galvanised and powder coated legs with optional armrest

Studio care & maintenance Ref: 01/A

Studio bench in natural finish FSC hardwood and bead blasted finish grade 316 stainless steel bench legs and armrests.

Studio bench in natural finish FSC iroko hardwood and galvanised and powder coated bench legs and armrest.

The Studio bench consists of a timber bench top bolted onto tubular steel bench legs.The bench is available with a choice of materials and finishes to suit your scheme and budget.

Timber bench top - will be manufactured in FSC iroko hardwood.Bench legs - will be manufactured from fully welded mild or stainless steel.

Timber bench top - will be left natural.Mild steel bench legs - will be hot dip galvanised.Stainless steel bench legs - will have a dull (brushed) polished finish.See material finishes sheet for more information and details of optional finishes.

Choose the bench lengths, material, finishes and installation type.

Choose from optional armrests, anti-skating studs and LED lighting.

The bench will be factory assembled and delivered to site fully assembled, for off-loading, ready for installation.

Materials

Standard finishes

Options

Accessories

Delivery

Overall dimensions

Installation options

Above ground installationThe assembled Studio bench will be secured to the finished ground level

with suitable fixings for thesurface type.

Below ground installationThe assembled Studio bench will be set into concrete foundations 600x400x550mm deep

Studio benchwith optional

single armrest

PRODUCT DETAILS

Studio bench without back

STUDIO seatingStreet Design LimitedUnit 47Hayhill Industrial EstateBarrow upon SoarLeicestershire LE12 8LD

Contact us:Telephone:Fax:Email:Web site:


FGL FGL

Ref: 10/A

Construction

Assembly

Materials

Options

Studio benches are manufactured to order.Before we can manufacture the benches, we need to know the following: bench lengths materials material finishes accessories required installation type required

•••••

The Studio bench is delivered to site fully assembled for off-loading ready for installation.

Dimensions

Plan dimensions:Bench 2000mm long x 500mm overall width.Other lengths are available on request.Overall height: Bench 450mmSitting height: Bench 450mm

The Studio bench design consists of a slatted timber bench top with tubular steel legs.The timber bench top is manufactured using FSC timber. The outer rails are 70x70mm section and the cross slats are 70x32mm section screw fixed to 38x38mm full length bearers.The timber top assembly is fixed to galvanised mild steel tubular bench legs.

General specification

ConstructionAll Street Design products are designed and manufactured using only quality, durable materials, construction details and fixings, to provide a long-lasting, durable product with a good life expectancy.AssemblyUnless otherwise stated all Studio benches will be supplied fully assembled and delivered to site ready for off-loading and installation.Timber policyAll iroko hardwood products are manufactured using materials obtained from growers who operate under the Forest Stewardship Council (FSC).MaterialsHardwood products are constructed from FSC iroko hardwood, from sustainable sources.All mild steel fabricated components will be hot dip galvanised after fabrication to BS EN ISO 1461:2009.All stainless steel fabricated components will be grade 304. Grade 316 can be specified if the location or project requires it.All mild steel fixings will be bright zinc plated, and all stainless steel fixings will be A2 (grade 304). A4 (grade 316) can be specified if the location or project requires it.FinishesFSC iroko hardwood will be left natural to reduce the need for re-staining and help reduce maintenance costs. If required, the timber can be supplied with a stained finish using 3 coats of quick drying water based wood stain, to the colour of you choice.Mild steel components will be left with a galvanised finish only. If required, after hot dip galvanising, the mild steel components can be polyester powder coated, to the colour of your choice. The galvanised parts are prepped, treated and sprayed with the polyester powder, before being baked in an oven.Stainless steel components will have a dull polished (brushed) finish. If required, the stainless steel components can be supplied with a mirror polished finish.

Guarantee

All benches are guaranteed for 15 years minimum. This guarantee is a minimum and is dependant on the product not being misused or abused. All the materials, treatments and construction will allow for a life expectancy considerably longer than this.

Product prices

See separate price list for the product prices of standard sizes, materials and finishes.

Timber topThe bench top is manufactured using either FSC treated European redwood or FCS iroko hardwood.Bench legsThe tubular bench legs will be manufactured from either fully welded mild or stainless steel.FixingsAll fixings will be mild steel M10 size and have a bright zinc plated finish.Security FixingAll bolts will be fitted with a M10 sizeKinmar security nut to preventunwanted removal.SamplesMaterial samples are available on request.

Studio planter bench in natural FSC iroko hardwood

Long Studio benches in natural FSC iroko hardwood

STUDIO seating

TECHNICAL SPECIFICATION

Street Design LimitedUnit 47Hayhill Industrial EstateBarrow upon SoarLeicestershire LE12 8LD



Ref: 11/A

The Studio bench can be manufactured and supplied to include a number of accessories to ensure that the product is right for your scheme.A number of armrests can be added to assist theless-abled to gain support whilst getting on or off the seating. The material will either be galvanised mild steel or dull polished stainless steel, with a FSC iroko hardwood top. As an additional optional extra. the galvanised mild steel can be polyester powder coated.

Optional armrests in natural FSC iroko hardwood with galvanised and powder coated bench leg and armrest.

ACCESSORIES

Armrests

LED Lighting

Anti-skateboard studs

We are able to supply the benches with stainless steel anti-skateboard fittings. The fittings are screwed to the outer 70x70mm section timber rails.

Optional anti-skateboard fitting in dull polished stainless steel, fixed to natural iroko hardwood slats.

Optional blue LED lighting fixed to the underside of the timber slats.

Coloured LED lighting can be supplied with your Studio seating.In its basic form, the lighting is available as cool white, warm white, blue, green or red LED units. More complex lighting can be supplied, including twilight switches, PIR sensors, timers, infrared, ultraviolet and royal blue emitters, PWM dimmers, RGB, UPS, DMX and remote control units.Our LED lighting units can handle all of the tasks formerly undertaken by tungsten, halide and fluorescent lamps, and out-perform them in every department. They are extremely flexible - we can supply almost any configuration of lighting to a client's specification using our standard lighting unit.The lighting units can be powered by either a low voltage DC supply or mains electricity. The choice of light levels and power units is also broad. Our standard power supply pumps out 12 Volts at 4 Amps, in LED terms enough for a very bright bench or seat. The entire range is from 1 Watt to 1,000 Watts.

STUDIO seating

Optional white LED lighting fixed to the underside of the timber slats.




Ref: 20/A

Standard mild steel finish

As standard, all FSC Studio bench tops will be supplied with a natural finish. Due to the nature of the material and the density of the grain, iroko hardwood is not capable of taking a preservative treatment. Iroko hardwood is a naturally durable material. Left to weather naturally, the timber will eventually turn a silver grey colour.

Optional timber finish

As an optional extra, the FSC iroko hardwood can be supplied with a stained finish. The standard stain will be 3 coats of Ronseal quick drying water based stain. The standard colour will be teak. Other stains and colours can be applied upon request.As part of the future maintenance, all stained products will require additional staining. The frequency of re-staining will depend on the location, use and the effects of weathering and traffic film. The products should be cleaned down, very lightly sanded and re-coated with the original stain.

As standard, all mild steel bench legs and armrests supports will be hot dip galvanised.

Optional mild steel finish

As an optional extra, the mild steel bench legs and armrest brackets can be polyester powder coated after galvanising. The polyester powder coating can be to a specified RAL colour and can have either a matt, satin or gloss finish.

Standard stainless steel finish

As standard, all stainless steel components will be supplied with a dull polished (brushed) finish.

Optional stainless steel finish

As an optional extra, the stainless steel components can be supplied with a mirror polished finish.

Dull polished

Natural iroko

Stained iroko

Mirror polished

Galvanised

Galvanised and powder coated

Standard timber finish

MATERIAL FINISHES

STUDIO seating

Aged natural iroko

Teak stain




Ref: 30/A

CARE & MAINTENANCE




Natural finish treated redwood can be washed down with a mild detergent. More stubborn surface marks can be removed with a light, hand sand with a 120 grit, or higher grade sandpaper. Excessive sanding should be avoided.

Maintaining the optional FSC treated redwood finish

Stained, treated redwood will need to be re-coated after a period of time. The stain can either start to fade, become dull (oxidised) or incur some surface break up. Lightly sand down the timber using a 120 grit, or higher grade sandpaper. We recommend that the timber is re-stained with the original stain colour and manufacturer. Details can be obtained from Street design Limited. Apply the stain evenly, with brush strokes running parallel with the woodgrain, in thin layers, building up the finish as recommended by the stain manufacturer.

STUDIO seating

Maintaining the standard stainless steel finish

Dull polished (brushed) stainless steel should be washed down with clean, warm water with a mild detergent. More severe marks can be removed by using a fine abrasive, such as a Scotchbrite or stainless steel scouring pad. As dull polishing is a process of applying fine linear scratches evenly over the surface, it is extremely important that rubbing down with a abrasive pad is done carefully in a straight line parallel to the existing grained finish. Rust marks or stains are usually caused by environmental contamination from dissimilar materials laid against, or near to, the stainless steel. These stains can be removed as described above.

Maintaining the standard FSC treated redwood finish Maintaining the standard mild steel finish

Maintaining the optional mild steel finish

Hot dip galvanised mild steel is a very durable and hard wearing finish. Dirt can be washed off with warm water and a mild detergent. Always use clean water and cleaning cloths to avoid surface contamination.After cleaning, any severe marks can be over painted with a cold galvanised, (zinc rich) aerosol spray.

Polyester powder coated finishes should be washed down with clean warm water and a mild detergent. Minor touching up can be done with an aerosol to match the original powder coated colour. Details can be obtained from Street Design Limited. More severe damage can be repaired by sanding down, by manual or mechanical means, beyond the damaged area, sufficiently far as to ensure that any step in the powder coated finish is removed. This will ensure that after re-finishing the repair will be difficult to detect.

General

Maintaining the optional FSC iroko hardwood finish

Maintaining the standard FSC iroko hardwood finish

All Studio seating products are manufactured using high quality materials, treatments and finishes. The timber slats are manufactured from either FSC treated redwood or FSC iroko hardwood. The fully welded mild steel legs and armrests will be hot dip galvanised after fabrication. The fully welded stainless steel will be supplied with a dull polished finish. All products require a varied amount of maintenance, depending on the environment, usage and weather conditions. Natural timber, galvanised steel and stainless steel will only require cleaning. In time, stained timber and powder coated mild steel will require re-coating.

Natural finish iroko hardwood can be washed down with a mild detergent.

More stubborn surface marks can be removed with a light, hand sand with a

120 grit, or higher grade sandpaper. Excessive sanding should be avoided.

Stained, iroko hardwood will need to be re-coated after a period of time. The stain can either start to fade, become dull (oxidised) or incur some surface break up. Lightly sand down the timber using a 120 grit, or higher grade sandpaper. We recommend that the timber is re-stained with the original stain colour and manufacturer. Details can be obtained from Street design Limited. Apply the stain evenly, with brush strokes running parallel with the woodgrain, in thin layers, building up the finish as recommended by the stain manufacturer.

Ref: 50/A

Documents

Street Design · specified if the location or project requires it. All mild steel fixings will be bright zinc plated, and all stainless steel fixings will be A2 (grade 304). A4 (grade