Summary NOM 030

7/31/2019 Summary NOM 030

1/7

NOM-030'S SUMMARY-MEXICO Acceptance criteria.

BULB TYPE

LUMINOUS EFFICIENCY

UNIDIRECTIONAL OMNIDIRECTIONAL

Minimum luminous

efficac lm W

Range of nominal luminous flux (lm) to A, BT, P,

PS T.

1

Higher than 1100 and less than or equal to 1600

Higher than 1600

55

5540

Higher than 6,35 45

Less than or equal to 6,35

55

50

50

55

.

Less than or equal to 325




Diameter (cm)Minimum luminous

effica (lm/W)

Higher than 300

40

Range of nominal luminous flux (lm) to BA, C, CA,

F y G.

Minimum luminous

efficacy (lm/W)

Less than or equal to 150


1


2/7


The initial luminous flux measured at the LED lamp have to emit more than 90% luminous flux specified in the package.

TOTAL NOMINAL LUMINOUS FLUX VARIATION


CORRELATED COLOR TEMPERATURE (CCT)

CCT MAINTAINED AND TOTAL MINIMUM LUMINOUS FLUX MAINTAINED.

CCT Tolerance (K)

Higher than or equal to 2 580 and less than 2 870



Higher than or equal to 3710 and less than 4 260

At the beginning and the end of a test equal to 25% of the lamp life (approx. 6,000 hrs), the lamp should continue within the ranges specified in the following

charts.

Nonimal CCT (K)

2700

3000

3500

4000

2


TOTAL MINIMUM LUMINOUS FLUX

Nominal lifetime(h)Maintained minimum luminous flux

(%)

Less than 15 000 83.2

95.8Higher than or equal to 50 000

Higher than or equal to 45 000 and less than 50 000 95.4


Higher than or equal to 15 000 and less than 20000 86.7





2


3/7


2. Two temperature cameras (-10C and 50C)


TEST TO THERMAL SHOCK RESISTANCE AND COMMUTATION

Undergo a test of thermal shock cycles, and a switching test and ultimately it will have to remain ignited 15 minutes

THERMAL SHOCK TEST

3. A l one test followin another until com lete 5 c cles. A c cle is

Procedure

Test conditions

1. Do not apply voltage to the sample

Temp.

C

Room Temperature

-20

-10

0

10

20

30

40

50

60

Hours

1 2 3 4 5 6 7 8 9 10

Heat shock cycle test (5 cycles)

3

one hour at -10C and one hour at 50C.

Temp.

C

Room Temperature

-20

-10

0

10

20

30

40

50

60

Hours

1 2 3 4 5 6 7 8 9 10

Heat shock cycle test (5 cycles)

3


4/7



2. All the directional lamps with a color temperature higher than 6000 K

must have more than 75% of RCI.

1. All the omni-directional lamps must have more than 77% of RCI.

COMMUTATION TEST

COLOR RENDERING INDEX (CRI).

1. All the directional lamps with a color temperature less than 6000 K

must have more than 77% of RCI.

Repeat this cycle until comply with number of cycles equal to half life time specified by the

manufactured (example: 20 000 hrs life time, 10 000 cycles).

Procedure

1. Turn on the lamp during 30 seconds and after that;

2. It must be turn off during 30 seconds

Conditions

1. Temperature: 25C 1C

2. Voltage: 127 10%

3. Frec: 60 Hz.

4

POWER FACTOR

1. For power below than 5 W, its not necessary to specify the power factor.

3. For power higher than 25 W, the minimum power factor is 0.7.2. For power higher than 5 W, the minimum power factor is 0.7.2. For power between 5 W to 25W, the minimum power factor is 0.5.

4


5/7


ELECTROMAGNETIC COMPATIBILITY

Support the application of 7 transients in a ring wave of 100 kHz at a level of 2.5 kV, both common mode and

differential mode and ultimately it will have to remain ignited at least 15 minutes-Reference Standard/Test Procedure:ANSI/IEEE C62.41-1991

TOTAL HARMONIC DISTORTION

Low harmonic distortion or THDi 30 %

55


6/7


The indelible is checked by inspection, by rubbing the marking by hand for 15 seconds with a cloth soaked in

water, after this test the information must be legible.

b) Nominal electrical data of input voltage, frequency, electric power, power factor and electrical current (1.

Frequency may be omitted if the lamp operates at 50 and 60 Hz, 2. Electrical current may be omitted if the

power factor is 0.9 or higher).

c) Date or code that allows to identify the manufacturing period (manufacturing date may be abbreviated or

use a code designated by the manufacturer).

In the products body.The products body must contain legibly and indelibly the following:

a) The name or trademark of the manufacturer or marketer;

6

d) If is necessary, mark "Do not use with dimmers."

Its possible:

e) Can be labeled with "high power factor" or "hpf" if the power factor is 0.9 or greater.

6


7/7


In the packaging:The packaging of integrated LED lamps covered by this draft standard should contain legibly and indelibly the

following information:

a) The graphic or product name, unless this is not visible or identifiable to the naked eye by the consumer.

b) Name, corporate name and address of the manufacturer or importer.

e) Type spatial light distribution and type of bulb.

c) The legend that identifies the country of the same (eg, "Made in ..."," Manufactured in ...", or similar.

d) Nominal electrical data input voltage, electric current, power factor, frequency and electric power,

7

h) Can be labeled with low harmonic distortion or THDi 30 % if the level of harmonic distortion measured

is less than 30%.

It should integrate a minimum warranty to product reposition for 3 years, counted from the sale. The warranty

can be printed in the packaging or added into the packaging.

i) If, the packaging indicate all the previous information, its not necessary added instructive.

Product warranty

t s necessary n cate t e content w en t e pro uct s not v s e to t e consumer.

g) Any other restriction is necessary indicate in the packaging.

Its possible:

7

Documents

Summary NOM 030