SUPPLIER!DETAILS! TOOL!DETAILS! · 2015-07-24 · Quebec!JOB5 3E4! 137Junction! Street! 0018198767131! AJ! Bedard! [email protected] CDK!Stone!Pty.Ltd.! Australia! 456Freighter!Rd!

SUPPLIER DETAILS TOOL DETAILS

RECOMMENDATIONS AND CONDITIONS

TYPE OF WORK: Cutting.

MACHINERY: Blade cutter or similar.

TOOL: Blade.

SUPPLIER: AGUILA DIAWERK,S.L. LOGO:

SALES CONTACTS Spain: Jordi Águila [email protected]; Tlf: +34.934.770.477 South America: Vicente Águila [email protected]; Tlf: +34 934.770.477 International/Rest of the world: Eugeni Fabregat [email protected]; Tlf:+34 934.770.477

REFERENCE: IKON • Diameter 300 mm. Segmented blade 300x10x2.4mm.• Diameter 350 mm. Segmented blade 350x10x2.6mm.• Diameter 400 mm. Segmented blade 400x10x2.8mm.OBSERVATIONS: Available in all diameters with the following versions:

1. Standard soul.2. Silent sandwich soul3. Reinforced soul for bezel cutting

The standard diameter is 60 mm, but it can be provided any size of internal diameter.

SECTION 1: BLADE CUTTER OR SIMILAR

CONDITIONS: -‐ A cutting speed of 0.7-‐0.9 m/min is recommended for all diameters. When frequency converter is available, 2400-‐2600 rpm are recommended for 300 mm diameter blade, 2100-‐2300 rpm for 350 mm and 1800-‐2000 rpm for 400 mm. -‐ If there is no frequency converter it is necessary to adjust the speed depending on the type of machine or change the blade diameter to achieve optimal cutting quality. -‐For large diameter blades (larger than 400 mm), take precaution with their vibration. In this case, lock washers are recommended. -‐ High volumes of cooling water pointing in the direction of the blade are necessary. OBSERVATIONS -‐ This tool gives a very high quality cutting result. PRIOR TO STARTING WORK -‐The blade should be in good condition. The cutting table should be solid and robust. It must be perfectly leveled and flat (the quality can be improved by using a rubber or wood surface to buffer the blade vibrations). -‐Check that the bench surface where the slab is going to placed is in good condition (i.e. that it is not covered in cuts in any one area, which might lead to the material moving). -‐If a special machine is available, in which cutting can be carried out while immersed in water, do the work in these conditions, as it can increase the speed, quality as well as the performance of the blade in general.

V6 July 2015






TOOL: Blade.

REFERENCE: Disco EVOGRES ZT12G 350MM DIMENSIONS: Ø 350 OBSERVATIONS: This tool gives a very high quality cutting result.

CONDICIONES -‐When frequency converter is available, 2.200-‐2400 r.p.m. are recommended for 350 mm diameter blade. A cutting speed is 1 m/s in all thickness. (0,6 m/s for white colors). -‐High volumes of cooling water pointing in the direction of the blade are necessary. PRIOR TO STARTING WORK -‐The blade should be in good condition. The cutting table should be solid and robust. It must be perfectly leveled and flat (the quality can be improved by using a rubber or wood surface to buffer the blade vibrations) -‐Check that the bench surface where the slab is going to placed is in good condition. (i.e. that it is not covered in cuts in any one area, which might lead to the material moving). -‐If a special machine is available, in which cutting can be carried out while immersed in water, do the work in these conditions, as it can increase the speed, quality as well as the performance of the blade in general.

SUPPLIER: ITALDIAMANT S.p.A. LOGO:

SALES CONTACT: Spain / Portugal: Jose Piqueres [email protected]; Tlf: +34 964 56 53 50 Italy: Enrico Bellotto [email protected]; Tlf:+390445 580750 France: Laura Boulen [email protected] E.E.U.U.-‐Canada-‐Mexico: Adriano Soso [email protected]; Tlf: +1 7062834104

Rest of the world:: [email protected]; +39 0445 580750





TOOL: Blade.

SUPPLIER: J-‐koenig GmbH LOGO:

SALES CONTACTS See attached table.

REFERENCE: DIAREX UCS cutting blade • Diameter 300 mm. Segmented blade 300x10x3.0mm. CodeF04.311516. • Diameter 350 mm. Segmented blade 350x10x3.0mm. Reinforcedcore. Code F04.320000 • Diameter 400 mm. Segmented blade 400x10x3.0mm Reinforcedcore. Code F04.322400 • Diameter 450mm. Segmented blade. 450x10x3.5mm. CodeF04.322670 OBSERVATIONS: It can be provided any size and type of internal diameter.


CONDITIONS: -‐ A cutting speed of 0.7-‐0.9 m/min is recommended for all diameters. When frequency converter is available, 2000-‐2200 rpm are recommended for 300 mm diameter blade, 1700-‐1900 rpm for 350 mm and 1500-‐1800 rpm for 400 mm. -‐ If there is no frequency converter it is necessary to adjust the speed depending on the type of machine or change the blade diameter to achieve optimal cutting quality. -‐ The diameter 350mm and 400mm have a reinforced steel core for maximum strength and stability to take out vibrations during the cutting process. -‐For large diameter blades (larger than 400 mm), take precaution with their vibration. In this case, lock washers are recommended. -‐ High volumes of cooling water pointing in the direction of the blade are necessary. OBSERVATIONS -‐ This tool gives a very high quality cutting result. PRIOR TO STARTING WORK -‐The blade should be in good condition. The cutting table should be solid and robust. It must be perfectly leveled and flat (the quality can be improved by using a rubber or wood surface to buffer the blade vibrations). -‐Check that the bench surface where the slab is going to placed is in good condition (i.e. that it is not covered in cuts in any one area, which might lead to the material moving). -‐If a special machine is available, in which cutting can be carried out while immersed in water, do the work in these conditions, as it can increase the speed, quality as well as the performance of the blade in general.

KOENIG exclusive partners: Name Country City Address Phone Contact email adress

J. Koenig GmbH & Co Germany DE -‐ 76227 Karlsruhe

Dieselstrasse 2 0049 721 409 050 Stefan Nichter

s.nichter@j-‐koenig.de

J. Koenig GmbH & Co Switzerland DE -‐ 76227 Karlsruhe Dieselstrasse 2 0049 721 409 050

Ghandi Elia g.elia@j-‐koenig.de

GranQuartz L.P. USA Tucker, GA 30084

4963 South Royal Atlanta

Drive 001 770 621 9777

GranQuatz Canada Inc. Canada Stanstead, Quebec JOB-‐

3E4

137 Junction Street 001 819 876 7131

AJ Bedard [email protected]

CDK Stone Pty.Ltd. Australia 4-‐6 Freighter Rd Moorabbin, Vic3189

0061 39 553 3055 James Clark

[email protected]

CDK Stone NZ Ltd New Zealand Unit 2, 40

Canaveral Drive Rosedale

0632 Auckland/ North Shore

City 0064 944 33932 Colin

Durling [email protected]

Gemba Maschinen-‐Handels Gmbh Austria A -‐ 1120 Wien Pottendorfer

Str. 5 0043 181 585 530 MichaelKriwan [email protected]

Diatool aps, Ingenior-‐og Denmark DK -‐ 8700 Horsens Lundvej 16 0045 756 54577

Klaus Andersen [email protected]

Industribehov Molde AS Norway N -‐ 6422 Molde Gammelseterlia11 0047 71 241680 Dagfinn

Gjerde [email protected]

Antiqua Hungary H -‐ 1108 Budapest X.

Kozma Utca 7 0036 12624365 Kornel Szabo

[email protected]

ADI Applicazione Diamante Indust.

Italy IT-‐ 36016 Thiene

Via dell Economia 12/16

0039 044 536 0244

Riccardo Petucco

[email protected]

FLADA s.r.o. Czek Republic CZ -‐ 351 34 Skalná

Stary Rybnik 123

0042 035 467 3247

Rita Skalova [email protected]

Waters Group Ltd. Great Britain GB -‐ Liskeard Cornwall PL143US

Quimperele Way / Liskeard Buisness Park

0044 845 658 5758

Daniel Waters

[email protected]

Waters Group Ltd. North Ireland GB -‐ Liskeard Cornwall PL143US

Quimperele Way / Liskeard Buisness Park

0044 845 658 5758

Daniel Waters

[email protected]

Koenig partners in other countries

B.V.B.A. GRUBAU Belgium BE -‐ 8560 Wevelgem Hoge Akker 1 0032 56 439 900

Ki-‐Venti cvba Belgium BE -‐ 8520 Kuurne Hoogstraat

20 0032 56 202040 Koen van Ysacker info@ki-‐venti.eu

DIA KH s.r.o. Slovakia SK -‐ 03601 Martin Na Bystricku 14

00421 434 237 909

Vladimir Krc-‐Jediny [email protected]

Abrasifs Yves Cornier France FR -‐ 38460 Crémieu

Villemoirieu 0033 47 4909767 Frederic Aumeran

[email protected]

Derognat & Cie. France FR -‐ 21700 Comblanchien

Route Nationale 74

0033 380 629 421 Jean-‐Michel

Rousseau [email protected]

S.A. Zucco France FR -‐ 11600 Conques Sur

Orbiel

2, Rue George Sand

0033 299 985 097

SAS Andre Marty France FR -‐ 81210 Lacrouzette

65, rue du Sidobre

0033 563 821 100

Van Voorden B.V. Netherlands NL -‐ 4870 AH Etten-‐Leur

Pauvreweg 22 0031 76 5021750

Ger Musters [email protected]

Firma "K & K" Katarzyna WIDUTO

Poland PL -‐ 86-‐050 Solec Kujawski

ul. Wrzosowa Nr. 8

0048 523 878 397 Mr. Widuto [email protected]

Thibaut France FR-‐ 14508-‐Vire

Cedex

Avenue de Bischwiller BP 88000

0033 231666803 Cedric Rollande

crollande@tsb-‐n1.com



PROVEEDOR : Tecnodiamant s.r.l. LOGO:

SALES CONTACTS: Central: Via Ghiarola Vecchia 53/m 41042 Fiorano Modenese ( MO) Italy v.a.t. 02301500365 tel. +39 0536 832939 e-‐mail [email protected] International: See attached table

REFERENCE: Blade BO-‐R/2 COS.3 AL • Diameter 300 mm. TDBOR2COS330026ALSTD. Segmentedblade 300x10x2,6. • Diameter 350 mm. TDBOR2COS335026ALSTD. Segmentedblade segmentado 350x10x2,6 • Diameter 400 mm. TDBOR2COS340032ALSTD. Segmentedblade 400x10x3,2. OBSERVACIONES: It can be provided any size and type of internal and external diameter

CONDITIONS: -‐ A cutting speed of 0.7-‐0.9 m/min is recommended for all diameters. When frequency converter is available, 2300-‐2500 rpm are recommended for 300 mm diameter blade, 2000-‐2200 rpm for 350 mm and 1700-‐1900 rpm for 400 mm. -‐ If there is no frequency converter it is necessary to adjust the speed depending on the type of machine or change the blade diameter to achieve optimal cutting quality. -‐For large diameter blades (larger than 400 mm), take precaution with their vibration. In this case, lock washers are recommended. -‐ High volumes of cooling water pointing in the direction of the blade are necessary. OBSERVATIONS -‐ This tool gives a very high quality cutting result. PRIOR TO STARTING WORK -‐The blade should be in good condition. The cutting table should be solid and robust. It must be perfectly levelled and flat (the quality can be improved by using a rubber or wood surface to buffer the blade vibrations). -‐Check that the bench surface where the slab is going to placed is in good condition (i.e. that it is not covered in cuts in any one area, which might lead to the material moving). -‐If a special machine is available, in which cutting can be carried out while immersed in water, do the work in these conditions, as it can increase the speed, quality as well as the performance of the blade in general.



TOOL: Blade.

.


Country Person of contact Email Phone Brazil Mr. Adriano Zabot [email protected] +55 4834328000 Italy and rest of the world

Mr. Lorenzo Tagliani [email protected] +39 0536 832939

Poland Mr. Jarek Piotrowski [email protected] +48 518918927 Portugal Mr. Paulo Manaia [email protected] +351 919738826 Spain Mr. Pascual Membrado [email protected] +34 964 550320 U.S.A. Mr. Emilio Vozzolo [email protected] +1 2123438749



PROVEEDOR : Vena LOGO:

SALES CONTACTS: Spain Luis Miguel Sanchez Hernandez [email protected] Phone: +34610107474 Germany and rest of the world Joseph Navarro (English, Spanish, German) j.navarro@vena-‐d.dePhone: +49 (0) 2737 982166

REFERENCE: • 300 mm, bore 60 mm, segment 8 mm. Order nº: T0302017• 350 mm, bore 60 mm, segment 8 mm. Order nº: T0352017

• 400 mm, bore 60 mm, segment 8 mm. Order nº: T0402017

•OBSERVACIONES:It can be provided any size and type of center bore and external diameter. Please indicate center bore and drive pin holes.

CONDITIONS: -‐ A cutting speed of 1.1-‐1.3 m/min is recommended for all diameters. When frequency converter is available, 2300-‐2500 r.p.m. are recommended for 300 mm diameter blade, 2000-‐2200 r.p.m. for 350 mm and 1700-‐1900 r.pm. for 400 mm. -‐ If there is no frequency converter it is necessary to adjust the speed depending on the type of machine or change the blade diameter to achieve optimal cutting quality. -‐For large diameter blades (larger than 400 mm), take precaution with their vibration. In this case, lock washers are recommended. -‐ High volumes of cooling water pointing in the direction of the blade are necessary. OBSERVATIONS -‐ This tool gives a medium high quality cutting result. The yield in linear meters is high. PRIOR TO STARTING WORK -‐The blade should be in good condition. The cutting table should be solid and robust. It must be perfectly leveled and flat (the quality can be improved by using a rubber or wood surface to buffer the blade vibrations). -‐Check that the bench surface where the slab is going to placed is in good condition (i.e. that it is not covered in cuts in any one area, which might lead to the material moving). -‐If a special machine is available, in which cutting can be carried out while immersed in water, do the work in these conditions, as it can increase the speed, quality as well as the performance of the blade in general.



TOOL: Blade.

.




SECTION 2: NUMERIC CONTROL

TYPE OF WORK: Cutting

MACHINERY: Numeric Control

TOOL: Specific milling cutter for DEKTON®.

SUPPLIER: ADI S.p.A LOGO:

SALES CONTACT: See attached table

REFERENCE: Milling cutter attacco 1/2"GAS Z=6 CODE: MT74010 DIMENSIONS: 19X25mm OBSERVATIONS Inform the supplier of type of coupling.

CONDITIONS 5000 rpm and 200 mm/min for any DEKTON® colour. High volumes of cooling water are required to ensure that the tool is perfectly cool to achieve a top quality cutting result.

TYPES OF WORK: -‐ Reduce the speed for work with tight corners. -‐

OBSERVATIONS -‐ This tool gives a top quality cutting result. -‐ For straight cutting, start diagonally to prevent the material from breaking. Then finish, by starting

with the side opposite to the one you started with. -‐ The suction pads must be well positioned to prevent the material from vibrating during the work.

Country Company Contact Phone

Italy and rest of the world

ADI SPA. Via dell’Economia, 12/16. 36016

Thiene (VI).

Ms. Barbara Nosella [email protected]

0039-‐0445 360244

Australia CDK STONE AUSTRALIA 4-‐6 Freighter Road 03189 MOORABBIN, VICTORIA

Mr. James Clark James.Clark@cdkstone

.com.au

0061-‐3-‐85526000

Austria GEMBA GMBH Pottendorfer Str., 5 01120 Wien

Mr. Michael Kriwan michael.kriwan@gemb

a.at

0043-‐1-‐8158553

Belgium GRUBAU Hoge Akker 1 08560 Wevelgem

Mr. David Rigole David.Rigole@grubau.

be

0032-‐56439900

Canada GRANQUARTZ CANADA INC. 137 Rue Junction Stanstead, PQ JOB

3E4

Mr Alain Bédard [email protected]

a

1 800 520-‐7223

France COMARTEX 40, Rue Gay Lussac-‐ B.P. 83 94432

CHENNEVIERES S/M CEDEX www.comartex.com

Mr. Frank Tribout [email protected]

0033-‐1-‐45765303

Germany J.KOENIG GMBH & CO. Dieselstrasse 2 76227 KARLSRUHE-‐DURLACH

Mr. Pietro Bazzan p.bazzan@j-‐koenig.deMr. Michael Thums

m.thums@j-‐koenig.de

0049-‐721-‐409050

New Zeland CDK Stone NZ Ltd 2/40 Canaveral Drive Rosedale Auckland

Mr. John Durling [email protected]

0064-‐09-‐4750495

Poland MACH PLUS ROBERT WALCZAK Ul. Miedzynarodowa 46/48/95

Warsawa

Mr. Robert Walczak [email protected]

0048 226133911

Portugal J.LEMOS ESTEVES LDA AV.VICTOR GALLO,72-‐3° ESQ

AP.79 2431-‐901 MARINHA GRANDE

Mr Joao Esteves Joao.Esteves@jlemose

steves.pt

351 -‐244-‐573480

Slovenia TEAL TRGOVSKO PODJET JE D.O.O.

Igriska 15 01235 RADOM LJE

Mr. Roman Luzar [email protected]

00386-‐1-‐4370123

Spain FREDIMAR S.A. Avd. Prat de la Riba N°186 NAVE 1 -‐ Zona Industrial 08780 PALLEJA -‐

BARCELLONA

Mr. Vicente Benlloch vicente.benlloch@fredi

mar.com

0034-‐93-‐6601396

Sweden MATEK AB ZINKGATAN 3 27139 YSTAD

Mr. Magnus Lasson magnus.lasson@matek

.se

0046-‐411-‐555725

Turkey MERTEKS, Nazmi Akbaci Sit. No.73 34398

Maslak Istanbul

Mr. Ufuk Artun [email protected]

90-‐212-‐3461730

Hungary ANTIQUA Kozma U. 7 01108 Budapest

Mr. L.Debnar [email protected]

0036 1 431 9088

UK and Ireland

WATERS GROUP LTD Owen Sivell CloseQuimperle Way -‐ Liskeard Cornwall PL14 3 US

England

Mr. Daniel Waters daniel.waters@waters

groupltd.co.uk

0044 845 6585758

U.S.A. GRANQUARTZ LP TUCKER, GA

Mr. Jim Callaghan jcallaghan@granquartz

.com

+1 248 660-‐3291




TYPE OF WORK: Countersinking

MACHINERY: Numeric control

TOOL: Countersink cutter

CODE: MT75020 REFERENCE: Sintered router for incremental cutting diam. 20x15 ½" gas fitting

CONDITIONS This tool is not used to cut and it is particularly recommended for countersinking depths of 0.1 mm to 5 mm per turn. Working with rpm from 5500 to 7500 is recommended and with a feed rate of 75 to 150 mm/min is recommended. The use of high volumes of cooling water is necessary to achieve a top quality cutting result.

OBSERVATIONS -‐ The suction pads must be well positioned to prevent the material from vibrating during the work.

SUPPLIER: ADI S.p.A.

LOGO:

SALES CONTACT: See attached table.

Country Company and address Contact person Phone Italy and rest of world

ADI SPA. Via dell’Economia, 12/16. 36016

Thiene (VI).


0039-‐0445 360244


Mr. James Clark [email protected]

m.au

0061-‐3-‐85526000


Mr. Michael Kriwan [email protected]

t

0043-‐1-‐8158553


Mr. David Rigole [email protected]

0032-‐56439900

Canada GRANQUARTZ CANADA INC. 137 Rue Junction Stanstead, PQ JOB 3E4


1 800 520-‐7223




0033-‐1-‐45765303

Germany J.KOENIG GMBH & CO. Dieselstrasse 2 76227 KARLSRUHE-‐

DURLACH

Mr. Pietro Bazzan p.bazzan@j-‐koenig.deMr. Michael Thums


0049-‐721-‐409050

New Zealand CDK Stone NZ Ltd 2/40 Canaveral Drive Rosedale Auckland


0064-‐09-‐4750495

Poland MACH PLUS ROBERT WALCZAK Ul. Miedzynarodowa 46/48/95 Warsawa


0048 226133911

Portugal J.LEMOS ESTEVES LDA AV.VICTOR GALLO,72-‐3° ESQ AP.79 2431-‐901 MARINHA GRANDE

Mr Joao Esteves Joao.Esteves@jlemoseste

ves.pt

351 -‐244-‐573480

Slovenia TEAL TRGOVSKO PODJET JE D.O.O. Igriska 15 01235 RADOM LJE


00386-‐1-‐4370123


BARCELLONA

Mr. Vicente Benlloch vicente.benlloch@fredim

ar.com

0034-‐93-‐6601396


Mr. Magnus Lasson [email protected]

0046-‐411-‐555725

Turkey MERTEKS, Nazmi Akbaci Sit. No.73 34398 Maslak

Istanbul


90-‐212-‐3461730



0036 1 431 9088

United Kingdom and

Ireland

WATERS GROUP LTD Owen Sivell CloseQuimperle Way -‐ Liskeard Cornwall PL14 3 US England

Mr. Daniel Waters daniel.waters@watersgro

upltd.co.uk

0044 845 6585758


Mr. Jim Callaghan [email protected]

m

+1 248 660-‐3291



TYPE OF WORK: Countersinking


TOOL: Countersink cutter

SUPPLIER: ADI S.p.A.

LOGO:

SALES CONTACT: See attached table.

Code Description

MT75015 Φ6x10 A=1/2” GAS

MT75016 Φ8x10 A=1/2” GAS

MT75017 Φ10x10 A=1/2” GAS

MT75018 Φ12x10 A=1/2” GAS


CONDITIONS This tool is not used to cut and it is particularly recommended for countersinking depths of 0.1 mm to 2 mm per turn. Working with 7200 rpm is recommended and with a feed rate of 50 mm/min is recommended. The use of high volumes of cooling water is necessary to achieve a top quality cutting result. The yield of the tool is low. OBSERVATIONS The suction pads must be well positioned to prevent the material from vibrating during the work.

Country Company and address Contact person Phone Italy and rest of world ADI SPA.

Via dell’Economia, 12/16. 36016 Thiene (VI).


0039-‐0445 360244


Mr. James Clark [email protected]

m.au

0061-‐3-‐85526000


Mr. Michael Kriwan [email protected]

t

0043-‐1-‐8158553


Mr. David Rigole [email protected]

0032-‐56439900

Canada GRANQUARTZ CANADA INC. 137 Rue Junction Stanstead, PQ JOB 3E4


1 800 520-‐7223




0033-‐1-‐45765303

Germany J.KOENIG GMBH & CO. Dieselstrasse 2 76227 KARLSRUHE-‐

DURLACH

Mr. Pietro Bazzan p.bazzan@j-‐koenig.de Mr. Michael Thums


0049-‐721-‐409050

New Zealand CDK Stone NZ Ltd 2/40 Canaveral Drive Rosedale Auckland


0064-‐09-‐4750495

Poland MACH PLUS ROBERT WALCZAK Ul. Miedzynarodowa 46/48/95 Warsawa


0048 226133911

Portugal J.LEMOS ESTEVES LDA AV.VICTOR GALLO,72-‐3° ESQ AP.79 2431-‐901 MARINHA GRANDE

Mr Joao Esteves Joao.Esteves@jlemoseste

ves.pt

351 -‐244-‐573480

Slovenia TEAL TRGOVSKO PODJET JE D.O.O. Igriska 15 01235 RADOM LJE


00386-‐1-‐4370123


BARCELLONA

Mr. Vicente Benlloch vicente.benlloch@fredim

ar.com

0034-‐93-‐6601396


Mr. Magnus Lasson [email protected]

0046-‐411-‐555725

Turkey MERTEKS, Nazmi Akbaci Sit. No.73 34398 Maslak

Istanbul


90-‐212-‐3461730



0036 1 431 9088

United Kingdom and Ireland

WATERS GROUP LTD Owen Sivell CloseQuimperle Way -‐ Liskeard Cornwall PL14 3 US England

Mr. Daniel Waters daniel.waters@watersgro

upltd.co.uk

0044 845 6585758


Mr. Jim Callaghan [email protected]

m

+1 248 660-‐3291







SUPPLIER: Continental D.I.A. LOGO:


REFERENCE:

Product Code Description DK.FB40 22mm x 40mm DK.FB50 22mm x 50mm

OBSERVATIONS Inform the supplier of type of coupling.

CONDITIONS 5000 rpm and 300 mm/min for any DEKTON® colour. High volumes of cooling water are required to ensure that the tool is perfectly cool to achieve a top quality cutting result. TYPES OF WORK:

-‐ Reduce the speed for work with tight corners. OBSERVATIONS

-‐ This tool gives a top quality cutting result. -‐ For straight cutting, start diagonally to prevent the material from breaking. Then finish, by starting with

the side opposite to the one you started with. -‐ The suction pads must be well positioned to prevent the material from vibrating during the work.

Country Company Phone E-‐mail

Poland TERMINATOR POLSKA +48 888 189 880 [email protected]

Italy MONTOLIT +39-‐388-‐4444111 [email protected]

France SA RAIMONDI DISTRIBUTION 2 S

0033 4 76069103 bsansone@raimondi-‐fr

Germany/Austria FLEISCHMANN & KOLLEGEN gmbh DEPARTMENT MONTOLIT

0049 9128 -‐7396-‐20

g.ziegler@fleischmann-‐kollegen.de

Norway SPESIALVERKTOY AS (0047) 22 81 26

96 [email protected]

Denmark CONSTRUX DANMARK

ApS 0045 98571998 [email protected]

Czech Republic PETR STEJSKAL-‐INTERTRADING PROFICENTRUM -‐

MONTOLIT

00420 2 72731327 [email protected]

Switzerland TECHNO SUPPORT &

SERVICE S.A. 0041 41 8591500 [email protected]

Switzerland (Italian side) EDILPOSA SA 0041 91 9309537

[email protected]

[email protected]

Former Yugoslavia DEKER D.O.O. 386-‐41-‐62-‐10-‐62 [email protected]

Rest of world CONTINENTAL +1-‐ 800 595 1237 or + 1 650 464





TYPE OF WORK: Polishing straight edge, matte and shiny finish


TOOL: Tool sequence.

CODES AND REFERENCES THICKNESS: 2 CM

POSITION TOOLS

1 M21TR3.C 2 M22TR3 3 M23TR3 4 M24TR3 5 C25TR3 6 C26TR3 7 C27TR3

OBSERVATIONS: Inform the supplier of type of coupling and weight to work with. This profile has been tested in the Cosentino installations and it functions correctly. For any other profile, contact the supplier.

CONDITIONS:

POSITION SPEED (mm/min) REVOLUTIONS (r.p.m.)

1 1.500 5000 2 2.500 5000 3 3.500 5000 4 1.250 4500 5 900 2400 6 1.000 2400 7 1000 2400

The use of high volumes of cooling water is necessary. OBSERVATIONS For MATTE finish edges, only use the first 4 positions and finish manually. For SHINY finish edges, use the complete sequence.

SUPPLIER: Continental D.I.A. LOGO:


Country Company Phone E-‐mail

France SA RAIMONDI DISTRIBUTION 2 S 0033 4 76069103 bsansone@raimondi-‐fr

Norway SPESIALVERKTOY AS (0047) 22 81 26


Denmark CONSTRUX DANMARK

ApS 0045 98571998 [email protected]

Switzerland TECHNO SUPPORT &

SERVICE S.A. 0041 41 8591500 [email protected]

Switzerland (Italian side) EDILPOSA SA 0041 91 9309537

[email protected]

[email protected]

Czech Republic PETR STEJSKAL-‐INTERTRADING PROFICENTRUM -‐

MONTOLIT

00420 2 72731327 [email protected]

Former Yugoslavia DEKER D.O.O. 386-‐41-‐62-‐10-‐62 [email protected]

Germany/Austria FLEISCHMANN & KOLLEGEN gmbh DEPARTMENT MONTOLIT

0049 9128 -‐7396-‐20

g.ziegler@fleischmann-‐kollegen.de

Italy MONTOLIT +39-‐388-‐4444111 [email protected]

Poland TERMINATOR POLSKA +48 888 189 880 [email protected]

Rest of world CONTINENTAL +1-‐ 800 595 1237 or + 1 650 464








SUPPLIER: DIAMUT (BIESSE GROUP)

LOGO:

SALES CONTACT:: [email protected] Tel :+39.0545.211900

CONTACTO TECNICO : Roberto Longato [email protected] Tlf: +39.366.7775761

REFERENCE: DDKFR10001 OBSERVATIONS Inform the supplier of type of coupling.

CONDITIONS 4000 rpm and 200 mm/min for any DEKTON® colour. High volumes of cooling water are required to ensure that the tool is perfectly cool to achieve a top quality cutting result. TYPES OF WORK:


-‐ This tool gives a top quality cutting result. -‐ For straight cutting, start diagonally to prevent the material from breaking. Then finish, by starting

with the side opposite to the one you started with. -‐ The suction pads must be well positioned to prevent the material from vibrating during the work.







SUPPLIER: Nicolai Diamant S.r.l. LOGO:


REFERENCE: Product Code Description AFS90272 Fresolina de corte D23 L40

½ Gas Z6 Twin FB23 AFS90128 Fresolina de corte D20 L25

½ Gas Z6 Twin FB23

CONDITIONS -‐ 4800 rpm and 200 mm/min for any DEKTON® color. -‐ High volumes of cooling water are required to ensure that the tool is perfectly cool to achieve a top

quality cutting result.

TYPES OF WORK: -‐ Reduce the speed for work with tight corners.

OBSERVATIONS -‐ This tool gives a top quality cutting result. -‐ For straight cutting, start diagonally to prevent the material from breaking. Then finish, by starting with


Country Company Contact E-‐mail

Belgium GRUBAU B.V.B.A. Mr. David Rigole [email protected]

Brasil Nicolai do Brasil LTDA

Mr. Marco Colmo [email protected]

Canada Nicolai Canada Mr. Kaveh Houshmand [email protected]

Denmark ENC NATURSTEN Mr. Henrik H. Madsen [email protected]

Germany WEISS Steintechnik GmbH

Mr. Sven Wappler sven.Wappler@weiss-‐steintechnik.de

Greece HATZIVARITI EPE Mr. Ioannis Vasiliou [email protected]

India Nicolai India Mr. Santhosh Kumar [email protected]

Ireland DIAMOND TOOL SUPPLIES

Mr. Brian McCann [email protected]

Italy and rest of the word

Nicolia central Via Dorsale, 13/B 54100 Massa (MS) Italy Phone +39 058579971

[email protected]

Middle East Nicolai Middle East Mr. Cataldo Tricase dino@nicolai_me.com

Norway INDUSTRIBEHOV MOLDE AS

Mr. Odde Magne [email protected]

Poland TGR SP. Z O.O. Mr. Tomasz [email protected]

Portugal Fresator

D2 Diamant

Mr. David Duarte

Mrs. Patrícia Coelho

[email protected]

[email protected]

Russlan Nicolai Russia Mrs. Svetlana Evseeva [email protected]

Schitzwerland STONELEC GMBH Mr. Andreas Knobel [email protected]

Slovenia ROKAM D.O.O. Mrs. Romina Žvab [email protected]

Spain Exclusivas UDA Mr. Fernando Verano [email protected]

UK ZAMBELIS DEMETRIS Mrs. Stella Zambelis [email protected]

USA Nicolai North America

Mr. Saba Vasanthan saba@nicolai-‐na.com


ATOS DE PROVEEDOR DATOS DE LA HERRAMIENTA






PROVEEDOR : Tecnodiamant s.r.l. LOGO:

SALES CONTACTS: Central: Via Ghiarola Vecchia 53/m 41042 Fiorano Modenese ( MO) Italy v.a.t. 02301500365 tel. +39 0536 832939 e-‐mail [email protected] International: See attached table

REFERENCE: Code Description

6.FRE26L48 Specific cutter for Dekton; high 30 mm, diameter 26 mm, length 48 mm, connection ½ gas

CONDITIONS -‐ 4200 rpm and 200 mm/min for any DEKTON® color. -‐ High volumes of cooling water are required to ensure that the tool is perfectly cool to achieve a top

quality cutting result. TYPES OF WORK:


-‐ This tool gives a top quality cutting result. The yield in meters is low. -‐ For straight cutting, start diagonally to prevent the material from breaking. Then finish, by starting with


Country Person of contact Email Phone Brazil Mr. Adriano Zabot [email protected] +55 4834328000 Italy and rest of the world

Mr. Lorenzo Tagliani [email protected] +39 0536 832939

Poland Mr. Jarek Piotrowski [email protected] +48 518918927 Portugal Mr. Paulo Manaia [email protected] +351 919738826 Spain Mr. Pascual Membrado [email protected] +34 964 550320 U.S.A. Mr. Emilio Vozzolo [email protected] +1 2123438749



SECTION 3: EDGE SHAPING

TYPE OF WORK: Polished finish.

MACHINERY: Edge shaping.

TOOL: Stones for polishing edges.

SUPPLIER: F.IM.A.D.

LOGO:

SALES CONTACTS: See table attached

REFERENCE:Mach2 Available grain Available grain

60 400 120 600 150 800 180 1000 220 1800 300 2000

3500 OBSERVATIONS: Inform the supplier of the type of coupling.

CONDITIONS: Recommended speed of line: 0.3-‐0.6 m/min. The use of high volumes of cool water is necessary. PRESSURE Depending on the type of machine, the pressure varies. As a general rule, a pressure of 2,5 bar can be consider appropriate for all the positions OBSERVATIONS The pressure of the heads on the edge should be as low as possible to prevent the special abrasives from breaking.

All of these parameters are tested on edge shapers, and so may be subject to slight changes depending on the type of machine.

For 8 motor machines, the recommended sequence: 80, 120, 220, 400, 600, 800, 1800, 3500. For 7 motor machines, the recommended sequence: 80, 150, 300, 600, 1000, 2000, 3500. For 6 motor machines, the recommended sequence: 100, 220, 400, 800, 1800, 3500.

Country Company Contact Email Phone

Italiy/France/Greece/Germany

FIMAD srl Luca Chemoli [email protected] +39 0331 981514

USA/Canada/ Mxxico

FIMAD INNOVATIONS

LLC Frank Humphreys

[email protected]

m+1 562 746 5059

Spain/Portugal FIMAD SPAIN BRANCH

Juan Pastor [email protected]

+34 651 135282

Benelux MARCOFLEX BV Michael Michot

michael.michot@marcoflex.

be+32 52 33 90 00

UK/Ireland WATERS GROUP ltd

Daniel Waters daniel.waters@bryanwaters

.co.uk+44 8456 585758

Brasil CAVI-‐FIMAD do BRASIL Vilma Mioni eleide@caviab

rasivos.com.br +55 11 4198 7167

Turkey ELMASTEK

Sanayi Tic. Ltd Kaan Yilmaz [email protected] +90 232 339 2713


ATOS DEL PROVEEDOR DATOS DE LA HERRAMIENTA


SECTION 3: EDGE SHAPING

TYPE OF WORK: Polished finish.

MACHINERY: Edge shaping.

TOOL: Stones for polishing edges.

SUPPLIER: Z-‐LION LOGO:

SALES CONTACTS: See attached table.

REFERENCE: Snail-lock Edge Polishing Pads, 5" ( ZL-EQ) y 6" (ZL-EH)

Available grain 50 100 200 400 800 1500 3000

OBSERVATIONS: Inform the supplier of the type of coupling

.

CONDITIONS: Recommended speed of line: 0.3-‐0.6 m/min. The use of high volumes of cool water is necessary. PRESSURE Depending on the type of machine, the pressure varies. As a general rule, a pressure of 2,5 bar can be consider appropriate for all the positions OBSERVATIONS The pressure of the heads on the edge should be as low as possible to prevent the special abrasives from breaking.

All of these parameters are tested on edge shapers, and so may be subject to slight changes depending on the type of machine.

For 7 motor machines, the recommended sequence: 50, 100, 200, 400, 800, 1500, 3000.

Country Contact Email Phone China Winnie Zhang zhili2@stone-‐tool.com +86-‐592-‐5507055 Brazil Durval Cortes [email protected] +55-‐28-‐9966-‐3067 USA (Vermont) Wayne Bailey [email protected] +1-‐800-‐396-‐8049 USA (Missouri) Beth Ni [email protected] +1-‐314-‐569-‐9390 USA (California) Jeff Hardin [email protected] +1-‐866-‐425-‐4693



SECTION 4: MANUAL MACHINE

TYPE OF WORK: Polished finish

MACHINERY: Manual Machine

TOOL: Resin disc for polished finish

PROVEEDOR: POMDI

LOGOTIPO:

CONTACTO: Alberto Oliva Flores [email protected] Tlf: +34 91 886 00 61

David Pozo Fernández [email protected] Tlf: +34 91 886 00 61

SUPPLIER: ABRASIVOS ÁGUILA

LOGO:

COMMERCIAL CONTACTS: Spain: Clemente Águila

+34936533058 [email protected]

Mexico: Juan Miernau Font

+52 224 271 4141 -‐ [email protected]

Rest of the world: José Bailón

+34 93 6533058 [email protected]

REFERENCE: LIJA FLEXIBLE DIAMANTADA B.R. Diameter: 100 mm.

Grain Ref. 60 1809 120 1810 220 1811 400 1812 800 1813 1800 1814 3500 1815 Gloss 1993

OBSERVATIONS -‐ Inform the supplier of type of coupling and size.

CONDITIONS The manual machine should rotate at a minimum of 4000 r.p.m. The water flow must be high and properly directed towards the polishing area to keep the material cool and achieve a good quality result. Pay attention that the manual machine has a continuous supply of water so that the product is kept cool. WORK First, grind using a diamond disk. Move the polishing machine gently over the material without applying pressure. When polishing, rather than remaining in the same position on the edge, the machine should be kept in constant motion. OBSERVATIONS The abrasives must be in good condition. The table and the piece being worked on should be well secured to prevent any movement during polishing.




TYPE OF WORK: Cutting or adjusting during installation.

MACHINERY: Manual machine.

TOOL: Cutting disc.

REFERENCE: Code Description

15377.ST00 DEKTOOL DISCO Ø 115 H:22,2 WET/DRY 15377.ST01 DEKTOOL DISCO Ø 115 M14 WET/DRY 15378.ST00 DEKTOOL DISCO Ø 125 H:22,2 WET/DRY 15378.ST01 DEKTOOL DISCO Ø 125 M14 WET/DRY 15379.ST00 DEKTOOL DISCO Ø 180 H:22,2 WET/DRY 15379.ST01 DEKTOOL DISCO Ø 180 M14 WET/DRY

DIMENSIONS: Ø 115-‐125-‐180 OBSERVATIONS: Possibility of attaching M14 aluminium strap.

CONDICIONES The manual machine should rotate between 7.000-‐ 10.000 r.p.m. for Ø 115 and Ø 125. The water flow must be high and properly directed towards the cutting area to keep the material cool and achieve a good quality result. Ensure that the cutting machine has a continuous supply of water so that the product is kept cool. WORK Start with slow feed rates until the disc reaches its full cutting capacity. Move the polishing machine gently over the material without applying pressure. OBSERVATIONS The tools must be in good condition. The table and the piece being worked on should be well secured to prevent any movement during polishing.


SALES CONTACT:: Spain: Jordi Águila [email protected]; Tlf: +34 934.770.477

Latin America: Vicente Águila [email protected]; Tlf: +34 934.770.477 International/rest of the world: Eugeni Fabregat [email protected]; Tlf:+34 934.770.477




TYPE OF WORK: Grinding plates

MACHINERY: Manual machine

TOOL: Manual grinding plates

REFERENCE: DEKTOOL LIJA VB Ø 100 H:22,2 OBSERVATIONS -‐ Inform the supplier of type of connection.

CONDITIONS The manual machine should preferably rotate at 7.000-‐10.000 r.p.m. The water flow must be high and properly directed towards the grinding area to keep the material cool and achieve a good quality result. Pay attention that the manual machine has a continuous supply of water so that the product is kept cool. WORK Move the polishing machine gently over the material without applying pressure. These tools can be used for manual grinding prior to the use of the discs for a matte or shiny finish, or to remove flaws in mitred or special edges. OBSERVATIONS The tools must be in good condition. The table and the piece being worked on should be well secured to prevent any movement during grinding.


SALES CONTACT:: Spain: Jordi Águila [email protected]; Tlf: +34 934.770.477 Latin America: Vicente Águila [email protected]; Tlf: +34 934.770.477 International/rest of the world: Eugeni Fabregat [email protected]; Tlf:+34 934.770.477


RECOMMENDATIONS AND CONDITIONS RECOMENDACIONES


TYPE OF WORK: Drilling


TOOL: Manual drilling

REFERENCE: Broca diamante corte en seco Size Reference 6 05988 8 05989 10 05990 12 05991 20 04910 28 04911 35 04912

35 (Rosca 5/8” USA) 05987 43 04913 50 04914 60 04915 65 04916 68 04917 75 05992

Adaptador M14 taladro eléctrico 05976

OBSERVATIONS -‐ Inform the supplier of type of coupling

CONDITIONS The manual machine should rotate between 7.000-‐10.000 r.p.m. WORK This drill must be used with water In order to do the drill, approach the material at a 45º angle until a 3 mm notch is made. Then, slowly straighten the drill until in a fully vertical position. At this time, make small circular movements until the work is completed. OBSERVATIONS The table and the piece being worked on should be well secured to prevent any movement during the work.

SUPPLIER: Rubi

LOGO:


COUNTRY COMPANY CONTACT EMAIL PHONE

Canada RUBI CANADA Mr. Daniel Bruneau [email protected] 1866 872 7825 Chile RUBI CHILE Sr. Héctor Lizana [email protected] (56-‐2) 2 933 74 92

Colombia RUBI COLOMBIA Sr. Rafael López [email protected] (571) 749 85 08 Finland RUBI SUOMI Mr. Kari Linsamo [email protected] 358 (0)9 2510 7400

France RUBI FRANCE S.A.R.L. Mr. Bruno Gallard [email protected] 33 1 69 18 17 85

Germany/ Austria RUBI DEUTSCHLAND

GmbH Mr. Reinhold Reismann [email protected] 49 (0) 2159 814 49 29

Italy GERMANS BOADA,

S.A Sr. Andrea Dallari [email protected] 800 788278 México and Central America RUBI TOOLS USA Inc. Sr. Aaron Cardelino [email protected] 1 305 715 9892 Middle East, Africa, Asia and Oceania

GERMANS BOADA, S.A Sr. Eduard García [email protected] 34 93 680 6500

Netherlands/ Belgium/ Luxemburg RUBI BENELUX BV. Mr. Engbert Broekman [email protected] 31 (0) 76 57 29 200

Poland RUBI POLSKA Sp.

z.o.o. Mr. Jerzy Szyszak [email protected] 48 (0) 226 44 51 61 Portugal LUSARUBI Lda. Sr. Humberto Galvao [email protected] 351 239 492 430

Rest of Europe GERMANS BOADA,

S.A Sr. Xavier Barba [email protected] 34 93 680 6500 Rest of Latin America

GERMANS BOADA, S.A Sr. Jordi Montagut [email protected] 34 93 680 6500

Russia RUBI ROSSIA Mr. Max Mitenko [email protected] 7 903 153 30 46

Spain GERMANS BOADA,

S.A Sr. Javier Saiz [email protected] 914 99 48 63

UK RUBI UK LTD. Mr. Vladimir Hoyos [email protected] 44 (0) 1708559609 USA RUBI TOOLS USA Inc. Mr. Ivan del Barrio [email protected] 1 305 715 9892

Venezuela RUBI VENEZUELA Sr. Alfredo Perdomo [email protected] (58-‐212) 0416 6105401


RECOMMENDATIONS AND CONDITIONS RECOMENDACIONES


TYPE OF WORK: Large format cutting at work (maximum width 1200mm)


TOOL: Cutter

REFERENCE: TX-‐700 –N, TX-‐900-‐N y Tx-‐1200-‐N OBSERVATIONS -‐ Each specified reference indicates the maximum size that can be cut. Specific use only for Dekton thicknesses of 8 and 12 mm.

SUPPLIER: Rubi

LOGO:

SALES CONTACT: In annexed table

CONDITIONS

The part must be well-‐supported to prevent movement during cutting.

WORK

Tool for dry work.

To make the cut, once the part is positioned and leveled, pass the roller one sole time in the direction of the cut

to be made. To separate parts, apply pressure to their edge with the lever.

OBSERVATIONS

Cuts may be cut angularly and longitudinally.

Interchangeable rollers of different sizes and diameters may be used according to the thickness of the part and

finish.

The cut is clean and generates no dust.

COUNTRY COMPANY CONTACT EMAIL PHONE

Canada RUBI CANADA Mr. Daniel Bruneau [email protected] 1866 872 7825 Chile RUBI CHILE Sr. Héctor Lizana [email protected] (56-‐2) 2 933 74 92

Colombia RUBI COLOMBIA Sr. Rafael López [email protected] (571) 749 85 08 Finland RUBI SUOMI Mr. Kari Linsamo [email protected] 358 (0)9 2510 7400

France RUBI FRANCE S.A.R.L. Mr. Bruno Gallard [email protected] 33 1 69 18 17 85

Germany/ Austria RUBI DEUTSCHLAND

GmbH Mr. Reinhold Reismann [email protected] 49 (0) 2159 814 49 29

Italy GERMANS BOADA,

S.A Sr. Andrea Dallari [email protected] 800 788278 México and Central America RUBI TOOLS USA Inc. Sr. Aaron Cardelino [email protected] 1 305 715 9892 Middle East, Africa, Asia and Oceania

GERMANS BOADA, S.A Sr. Eduard García [email protected] 34 93 680 6500

Netherlands/ Belgium/ Luxemburg RUBI BENELUX BV. Mr. Engbert Broekman [email protected] 31 (0) 76 57 29 200

Poland RUBI POLSKA Sp.

z.o.o. Mr. Jerzy Szyszak [email protected] 48 (0) 226 44 51 61 Portugal LUSARUBI Lda. Sr. Humberto Galvao [email protected] 351 239 492 430

Rest of Europe GERMANS BOADA,

S.A Sr. Xavier Barba [email protected] 34 93 680 6500 Rest of Latin America

GERMANS BOADA, S.A Sr. Jordi Montagut [email protected] 34 93 680 6500

Russia RUBI ROSSIA Mr. Max Mitenko [email protected] 7 903 153 30 46

Spain GERMANS BOADA,

S.A Sr. Javier Saiz [email protected] 914 99 48 63

UK RUBI UK LTD. Mr. Vladimir Hoyos [email protected] 44 (0) 1708559609 USA RUBI TOOLS USA Inc. Mr. Ivan del Barrio [email protected] 1 305 715 9892

Venezuela RUBI VENEZUELA Sr. Alfredo Perdomo [email protected] (58-‐212) 0416 6105401


CONDICIONES DE USO Y RECOMENDACIONES


TYPE OF WORK: Grinding plates


TOOL: Manual grinding plates

REFERENCE: Code Reference Diameter

70184640590 Pro Surf 115xM14

115 mm

70184640591 Pro Surf 125xM14

125 mm

OBSERVATIONS -‐ Inform the supplier of type of coupling.

CONDITIONS The manual machine should preferably rotate at 7.000-‐10.000 r.p.m. The water flow must be high and properly directed towards the grinding area to keep the material cool and achieve a good quality result. Pay attention that the manual machine has a continuous supply of water so that the product is kept cool.

WORK Move the polishing machine gently over the material without applying pressure. These tools can be used for manual grinding prior to the use of the discs for a matte or shiny finish, or to remove flaws in mitred or special edges. They can be use also to cut the material manually. OBSERVACIONES La mesa y la pieza deberán estar bien apoyadas para evitar movimientos durante el rectificado

SUPPLIER: Saint Gobain LOGO:


Country Address Phone Web Germany Saint-‐Gobain Abrasives GmbH

Wesseling + 49 (0)

223689110 sales.ngg@saint-‐gobain.com

Argentina Saint-‐Gobain Abrasivos Buenos Aires

+54 11 59013622 dma.sga.arg@saint-‐gobain.com

Asian Pacific 7th Floor, Office Tower, Bund Center

222 Yan'an Road (East) Shanghai 200002

+86 21-‐6361 8899 www.saint-‐gobain.com.cn

Australia 4-‐6 Colbert Road, Campbellfield

Vic 3061 +61 3 93 58 61 00 David.Shandley@saint-‐

gobain.com

Austria Saint-‐Gobain Abrasives GmbH + 49 (0)

223689110 sales.ngg@saint-‐gobain.com

Belgium Saint-‐Gobain Abrasives N.V.

Heide 10 1780 Wemmel

+3222672100

Brasil and Chile Avenida Santa Marina, 482

Agua Branca SP 05036-‐903 São Paulo

+55 (11) 2246 7622;

+ 55 11 2138-‐5155

sac-‐sga@saint-‐gobain.com

Canada Saint-‐Gobain Abrasives Canada Inc.

3 Beach Road Hamilton, Ontario L8L 7Y5

905-‐547 2551

South Korea

Youngpoong Building IS"" Floor, 33, Seorin-‐dong,

Jongno-‐gu Seoul 110-‐752

+82 2 3706 9180 www.hanglas.com

Denmark Saint-‐Gobain Abrasives A/S

Korskildeeng 5 Greve, DK 2670

+ 45 46755244

Egypt Zahret EIMaadi Tower, Maadi -‐ Heiwan

+202 (252) 88 070

United Arab Emirates PO Box 643706

Fortune Tower office 2106 JLT Block C Jumeira Lake Towers, Dubai

+971 4 431 5154 ; + 971 48817836

abrasives-‐emea@saint-‐gobain.com

Slovakia, and East Adriatic Countries

Pocernicka 272/96 108 00 Prague 10

+420 296 411 777 www.saint-‐gobain.com

Spain, Algeria and Tunisia Saint-‐Gobain Abrasivos SA Ctra. Guipuzcoa Km 7,5

Berrioplano (Navarra). E-‐31195

+34 (91) 948 306000

Central Europe Viktoriaalle 3-‐5 D-‐52066 Aachen +49 (241) 51 60 www.saint-‐gobain.de

France Rue de L Ambassadeur B.P. 8 78702 Conflans Cedex

+ 33 (0) 1 34 90 40 00

UK, Ireland, Mozambique, Namibia y Zimbabue

Saint-‐Gobain House Binley Business Park Coventry CV3 2TT United Kingdom

+44 (0) 2476 56 0700 + 44

(0)1785223281

www.saint-‐gobain.co.uk

The Netherlands Groenloseweg 28 7151 Hw Eibergen

+31 545 466466

Hungary Saint-‐Gobain Abrasives BV

1225 Budapest Bányaleg U. 60/B

+36 1 371 22 50 [email protected]

India, Sri Lanka and Bangladesh

Level 5, Leela Business Park Andheri Kurla Road,

Andheri (East) Mumbai -‐ 400059

+ 91 (022) 40 21 21 21 www.saint-‐gobain.co.in

Indonesia PT Saint-‐Gobain Abrasives Indonesia Surabaya

+62 318474358 Paulus.Tanuwijaya@saint-‐gobain.com

Italy, Greece, Turkey and Libya

Saint-‐Gobain Abrasivi S.p.A. Via E. Romagnoli, 6

20146 Milan

+39 (0) 2 42 431; + 39 024485227

distribution.italia@saint-‐gobain.com

Japan Saint-‐Gobain Bldg

3-‐7 Kojimachi, Chiyoda-‐ku 102-‐0083 Tokyo

+81 (3) 52 75 08 61

+81 470863735

akk.customer@saint-‐gobain.com

Luxemburg 190 Rue J.F.Kennedy L-‐4930 Bascharage

+352 50 401 1

Malaysia Saint-‐Gobain (SEA) PTE. Ltd. Singapore

+ 65 63372276 Parag.Kunte@saint-‐gobain.com

Morocco

Saint-‐Gobain Abrasifs S.A 2 Allée des figiers

Ain Sebaa Casablanca

+212 5 22 66 57 31 ;

+ 212 2665731

salesmaroc@saint-‐gobain.com

Mexico, America Central, Colombia, Ecuador y Peru

Horacio no. 1855-‐502 Colonia Polanco 11510 Mexico DF

+52 (55) 52 79 16 00 www.saint-‐gobain.com.mx

North America 750 E Swedesford Road

PO Box 860 Valley Forge, PA 19482-‐0101

United States

+1 (610) 341 70 00

www.saint-‐gobain-‐northamerica.com

Norway Postboks 11, Alnabru, 0614 Oslo + 47 63 87 06 00 sga.no@saint-‐gobain.com

Baltic and Nordic Countries

Robert Jacobsens Vej 62A DK-‐2300 Copenhagen S

+45 70 300 688

Poland and Bulgaria

Saint-‐Gobain Abrasives Sp.z o.o. Atrium Plaza

Al. Jana Pawla II 29 00-‐867 Warszawa

+48 (22) 653 79 00;

+ 48 632617100 www.saint-‐gobain.pl

Portugal

Saint-‐Gobain Abrasivos L.da Zona Industrial da Maia I-‐Sector VIII, No. 122. Apartado 6050.4476-‐908

Maia

+ 351 229 437 940

Czech Republic Saint-‐Gobain Abrasives s.r.o Windhraska 184, 130 52 Praha 3

+ 420 267 132 026

+420 267 132 09; + 420 267132256

Romania

(Danube – Balkans area) str Tipografilor 11-‐15, S-‐Park, Building B3-‐B4, 3rd floor

013714 Bucharest

+40 21 207 57 00; 00 40 261750009 www.saint-‐gobain.ro

South Africa Saint-‐Gobain Abrasives (PTY) Ltd

77 Ostend Road Cermiston South

+27 (0) 11 345 5300

sgasa@saint-‐gobain.com

Sweden Saint-‐Gobain Abrasives AB SE-‐191 24 Sollentuna

+ 46 8 580 881 00

sga.se@saint-‐gobain.com

Thailand 539/2 Gypsum Metropolitan Tower Si Ayutthaya Road, Ratchathewi

Bangkok 10400

+66 (0) 2 640 5410

+ 662 6405444 www.saint-‐gobain.co.th

Turkey Mueyyetzade Mah.

Galipdede Cad. No. 99 KAT :3 34425 Beyoglu-‐ Istanbul

0090 212 245 85 21

Ukraine, Russia and other CEI countries

Lefort Business Centre 107023 Moscow

+7 (499) 929 55 70; + 74

959373223

Venezuela Saint-‐Gobain Abrasivos C.A Miranda

+ 58 02122104800

atencionalcliente.sgav@saint-‐gobain.com





MACHINERY: Manual Machine


PROVEEDOR: POMDI

LOGOTIPO:

CONTACTO: Alberto Oliva Flores [email protected] Tlf: +34 91 886 00 61

David Pozo Fernández [email protected] Tlf: +34 91 886 00 61

SUPPLIER: SIGMADIAMANT, QUALITY DIAMONDS.

LOGO:

COMMERCIAL CONTACTS: See attached table

REFERENCE: Disco flexible Ø 100 Grain Ref. 50 RESA10050 80 RESA10080 300 RESA100300 400 RESA100400 800 RESA100800 1500 RESA1001500 3000 RESA1003000



Country Person of

contact Email Phone

Brazil Jesus Pina [email protected]

+55 2733383851

Mexico Oswaldo de la Rosa/ Martin Ontiveros

[email protected]/ [email protected]

+52 8182120531

Poland Manuel Beltrán

[email protected] +48 512316201

Portugal

Francisco Neves

[email protected] +351 234727080

Rusia Anna Khovorostenko

[email protected] + 7 4956654617 / +7 9166837749

Spain and rest of the world

Javier Gomez

Salvador Guinot

[email protected]

[email protected]

+34 679 501 885

+34 606 819 213

Turkey

Önder Okan

[email protected].

+90 2128553930 +90 5326119537

USA Jim Callaghan

[email protected]

+1 248 660 3291







.

REFERENCE: Three positions are necessary (EvoPad Pos.1, Pos.2, Pos.3.)



SUPPLIER: TENAX S.p.a. LOGO:

COMMERCIAL CONTACTS: SPAIN AND PORTUGAL: Miguel Fabregues [email protected] +34 609456450 NORTH AMERICA: Filippo Emanuel [email protected] Tlf: 001 704 583 1173 SOUTH AMERICA: Marcio Mathias [email protected] Tlf: +55 27 3038-‐7525 REST OF EUROPE, ASIA AND AUSTRALIA: Paolo Borgherini [email protected] Tlf: +39 0571 401482 MIDDLE EAST: Franco Favero [email protected] Tlf: +90 312 3947424


TYPE OF WORK: Laminate

MACHINERY: Application guns and mixing nozzles

TOOL: Specific DEKTON putties

REFERENCE:

COLOUR REFERENCIA AKEMI ARTICLE NO. OF AKEMI

Ananke Black CC 1040 47005 Arinae White CC 1100 47011 Danae Cream CC 1650 47066 Domoos Black CC 1010 47002 Kadum Brown CC 2050 47106 Keranium Brown CC 2060 47107 Sirius Black CC 1020 47003 Sirocco Grey CC 1840 47085 Strato Grey CC 1840 47085 Zenith White CC 1130 47014

OBSERVATIONS: - Adhesive only for INDOOR applications. Leave to polymerise for at least 30 minutes.

SUPPLIER: AKEMI

LOGO:

SALES CONTACT:

SECTION 5: LAMINATE


PRIOR TO WORK - Grind first the surfaces to be glued with the diamond disk until fully flat. - Check that the glued surfaces are totally clean, dry and roughened before sticking. - Surface and adhesive should both be at room temperature. - For a deck seam, apply masking tape on each side of the seam, back about 1.5mm from the joint (build up 2 to 3 layers of tape). APPLICATION - Remove the claps from the cartridge and put the cartridge in the gun. Work the grip until material emerges from both openings. - Attach mixing tip to cartridge and dispense. - Discard the first 5-10 cm to ensure hardener is present in mixture. - Apply adhesive on the surface to be bonded. Clamp the surfaces together making sure to leave some adhesive in the joint. A gap of 1 mm or more will provide improved flexural and impact strength. Stick both pieces with the mixture and apply pressure for at least 30 minutes at 20-25°C for its polymerization. The adhesive is workable during the first 5-7 minutes. - The hardening process is accelerated by heat and delayed by cold. - For deck seam: after the product has cured (30 minutes) it can be scraped flush with a razor blade. - For mitre: after the product has cured (30 minutes), the seam can be polished to enhance the color and smooth the surface. ACCESSORIES FOR COLOUR BOND CARTRIDGES

PRODUCT AREA OF APPLICATION ARTICLE NO. OF AKEMI Mixing Nozzle 10:1 for 250 ml and 490 ml cartridge 10:1

Mixing nozzle for squeezing the adhesive into the groove reinforcement.

10552

Metall gun 10:1 – manual for 250 ml cartridge 10:1

Used to squeeze out the adhesive in cartridges. 14030

Skeleton gun MR200X – manual for 250 ml cartridge 10:1

Used to squeeze out the adhesive in cartridges. 14029

COUNTRY COMPANY PHONE FAX EMAIL

Germany AKEMI CHEMISCH TECISCHE SPEZIALFABRIK GMBH LECHSTRAßE 28 D-90451 NUERMBERG

+49 (0) 911 - 64 29 60 +49 (0) 911 - 64 44 56 [email protected]

WILH. GOLDSCHMIDT GMBH & CO. KG IM UNTEREN RIED 15 75382 ALTHENGSTETT

+49 (0)7051 - 92 02 0 [email protected]

KREKLAU & HAGEDORN GMBH & CO. KG KANALSTRASSE 16 30926 SEELZE

+49 (0)5137 - 42 31 [email protected]

SCHLINGELHOFF - SCHLEIFMITTEL GMBH KIRCHSTRASSE 37 85131 POLLENFELD

+49 (0)8421 – 90 12 09 [email protected]

WEHA - LUDWIG WERWEIN GMBH WIKINGER STRAßE 15 86343 KÖNIGSBRUNN

+49 (0)8231 – 60 07 - 0 [email protected]

AUSTRIA WEHA-STEINBEARBEITUNGSMASCH. VERTRIEBSGES. MBH LANGE GASSE 17 1080 Vienna

+43 1 40 39 340 +43 1 40 39 34 040 [email protected]

GEMBA G.M.B.H. POTTENDORFER STRASSE 511200 Vienna

+43 1 81 58 553 +43 1 81 58 55 322 [email protected]

BELGIUM AKEMI BENELUX BVBA – SPRL KROMSTRAAT 58 2520 RANST

+32 3 354 35 60 +32 3 354 35 61 [email protected]

BRAZIL DUPOX IND. E COM. PRODUTOS QUIMICOS PARA CONSTRUCAO LTDA. AV. MARECHAL CASTELO BRANCO NO 350, JARDIM TRES MARIAS CEP: 06790-070 TABOAO DA SERRA – SP

+55 11 41 38 80 10 +55 11 41 38 80 10 [email protected]

CHILE RAVENA S.A. AV. LAS CONDES AV. LAS CONDES 9507, 7591151 SANTIAGO

+56 29 52 65 65 [email protected]

CHINA AKEMI BEIJING CO. LTD. ROOM 2704, UNIT1, BUILDING 2 YUELAN BAODI INT. AP. 39, NANMOFANG ROAD CHAOYANG DISTRICT 100022

+86 10 87 79 49 52 +86 10 87 79 61 63 [email protected]


CZECH REPUBLIC

FLADA S.r.o. STARY RYBNIK 123 351 34 SKALNA

+420 35 46 73 247 +420 35 46 73 247 [email protected]

DENMARK DIATOOL APS LUNDVEJ 16 8700 HORSENS

+45 75 65 45 77 +45 75 75 65 49 70 [email protected]

ESTONIA KEMISTEIN OÜ BENSU2, VIT KÜLA HARKU VALD 76901

+372 64 45 160 +372 64 45 162

[email protected]

FRANCE DEGAMI SA 46-48 RUE DE CONFLANS 94220 CHARENTON-LE-PONT

+3301 43 68 00 17 +3301 43 75 49 98 contact @degami.fr

GREAT BRITAIN

APEX GRANGE LTD. ATTN: MR. JOHN BASS 14 LITTLE MUDELLS MUDELLS INDUSTRIAL CENTRE AL7 1EW WELWYN GARDEN CITY

+44 1707 338800 +44 1707 338811 [email protected]

C. R. LAURENCE OF EUROPE LTD. CHARLES BABBAGE AVENUE KINGSWAY BUSINESS PARK ROCHDALE LANCASHIRE OL16 4NW

+44 170 68 63 600 +44 170 86 98 60 [email protected] [email protected]

HUNGARY ANTIQUA KOFARAGO, GEP., SZERSZAM ES ANAYAGKERESKEDES KOZMA UTCA. 7 1108 BUDAPEST X

+36 12 62 43 65 +36 12 62 4366 [email protected]

INDIA AKEMI TECHNOLOGY INDIA PVT LTD PLOT NO. 276,KANCHANAYAKANA HALLI SUB LAYOUT,PHASE 1, BOMMASANDRA INDUSTRIAL AREA JIGANI HOBLI, ANEKAL TALUK, 560100 BANGALORE - KARNATAKA

+91 92 43 62 67 77 [email protected]

IRAN PAVIR CO. (MINING & TRADING HOLDING ) HEAD OFFICE ADD.:BETWEEN #18TH&20 ST. MAHMOUDABAD INDUSTRIAL ZONE, ISFAHAN, IRAN

+98 31 13 80 14 - 85

+98 38 01 985 - 86

+98 311 380 14 - 86 [email protected]

ITALY CEAM S.R.L. VIA DELLE LARE, 15 55045 PIETRASANTA (LU)

+39 05 84 79 24 49 +39 05 84 28 45 03 [email protected]


JAPAN TOUEI KENZAI INDUSTRIAL CO. LT 4-5-25 WAKAE NISHISHIN-MACHI HIGASHIOSAKA-CITY OSAKA

+81 6 67 25 52 36 +81 6 67 25 52 36 [email protected]

KOREA CPPM SERVICES INC. #105, SONGSAN BLDG, 279 DONGSOMUN-DONG-4KA, SUNGBUK-KU SEOUL 136-750

+822 92 71 114 +822 74 58 114 [email protected]

NORWAY S. TANDBERG A/S P.O. BOX 63 NESVEIEN 13 1344 HASLUM

+4767 83 06 00 +4767 83 06 01 [email protected]

POLAND KONTIN-STONE Sp. z o.o. UL. HAUKE BOSAKA 11/9> 25-217 KIELCE

+48 41 36 12 254 +48 41 36 11 984 [email protected]

PORTUGAL

PINHAO & IRMAO, LDA. FUNDACAO DE METAIS RUA DA TAPADINHA, NO. 53 APARTADO 458 4524-907 RIO MEAO

+351 25 67 82 679 +7 499 25 98 460 [email protected]

RUSSLAND N. SERVICE LTD. ZVENIGORODSKOE SHOSSE 28/1 123317 MOSCOW

+7 925 58 58 310 +351 25 67 81 053 [email protected]

SCHWEDEN MATEK AB N. ZINKGATAN 3 271 39 YSTAD

+46411 55 57 25 +46411 55 58 30 [email protected]

SLOVAKIA DANBIK s.r.o. KADNAROVA 51 83151 BRATISLAVA

+4211 44646262 +4211 44646263 [email protected]

SPAIN XABIER ALDANONDO DEL CAMPO C/JOSE MA SALABERRIA, 39 4 - E 20010 DONOSTIA-SAN SEBASTIAN

+34 626413312 [email protected]

SCHWITZER-LAND

FERRONATO AG RIED 5420 EHRENDINGEN

+41 56 20 40 140 +41 56 20 40 149 [email protected]

UKRAINE LORI-R BUILDING 27, FLAT 55, VERKHOVNIY SOVIET AVENUE 02094 KIEV

+380 44 29 15 137 +380 44 55 93 065 [email protected]

USA INNOCHEM LLC 4030 PLEASANTDALE ROAD SUITE F, DORAVILLE, GEORGIA 30340

+1 770 40 98 789 +1 770 40 99 096 [email protected]



MACHINERY: Application guns and mixing nozzles

TOOL: Specific DEKTON® putties

REFERENCE:

COLOUR REFERENCIA AKEMI ARTICLE NO. OF AKEMI

Platinum liquid

Transparent clear adhesive for horizontal application 10726

Platinum knife-garde

Transparent clear adhesive for horizontal and vertical application 10726

OBSERVATIONS: - Transparent adhesive only for INDOOR applications. Can be coloured with AKEMI Colouring Paste or AKEMI Colouring Concentrates for polyester and epoxyacrylate based adhesives. Leave to polymerise for at least 30 minutes.

SUPPLIER: AKEMI

LOGO:


SECTION 5: LAMINATE


PRIOR TO WORK -‐ Grind first the surfaces to be glued with the diamond disk until fully flat. -‐ Check that the glued surfaces are totally clean, dry and roughened before sticking. -‐ Surface and adhesive should both be at room temperature. -‐ For a deck seam, apply masking tape on each side of the seam, back about 1.5mm from the joint (build up 2 to 3 layers of tape).

APPLICATION -‐ Colouring is possible by adding AKEMI Colouring Pastes or AKEMI Concentrates for polyester and epoxyacrylate based adhesives up to max. 5%. -‐ Add 1 to 3 g of white hardener paste to 100g of adhesive. -‐ Mix both components thoroughly. The mixture can be worked for about 5 to 15 minutes. -‐ Apply adhesive on the surface to be bonded. Clamp the surfaces together making sure to leave some adhesive in the joint. A gap of 1 mm or more will provide improved flexural and impact strength. Stick both pieces with the mixture and apply pressure for at least 30 minutes at 20-‐25°C for its polymerization. -‐ The hardening process is accelerated by heat a delayed by cold. -‐ For deck seam: after the product has cured (30 minutes) it can be scraped flush with a razor blade. -‐ For mitre: after the product has cured (30 minutes), the seam can be polished to enhance the color and smooth the surface.

ACCESSORIES FOR COLOUR BOND CARTRIDGES -‐ Colouring Pastes for adhesives based on epoxyacrylate. Consitency: paste-‐like.

PRODUCT AREA OF APPLICATION ARTICLE NO. OF AKEMI red redbrown white black ochre green brown blue 8 colours, assorted (see above)

Used for colouring Platinum to match the colour of the filler with that of the re-‐spective stone DEKTON.

11001 11002 11003 11004 11005 11006 11011 11012 11007

-‐ Colouring concentrates liquid for adhesives based on expoxyacrylate. Consitency: liquid.

COLOURING CONCENTRATE AREA OF APPLICATION ARTICLE NO. OF AKEMI red redbrown white black ochre green brown blue beige grey 10 colours, assorted (see above)

Used for colouring Platinum to match the colour of the filler with that of the re-‐spective DEKTON. The liquid consistency makes it easier to mix the colouring concentrate with PLATINUM LIQUID.

11050 11051 11052 11053 11054 11055 11056 11057 11058 11059 11060


Germany AKEMI CHEMISCH TECISCHE SPEZIALFABRIK GMBH LECHSTRAßE 28 D-‐90451 NUERMBERG

+49 (0) 911 -‐ 64 29 60 +49 (0) 911 -‐ 64 44 56 [email protected]

WILH. GOLDSCHMIDT GMBH & CO. KG UNTEREN RIED 15 75382 ALTHENGSTETT

+49 (0)7051 -‐ 92 02 infoah@goldschmidt-‐w.de

KREKLAU & HAGEDORN GMBH & CO. KG KANALSTRASSE16 30926 SEELZE

+49 (0)5137 -‐ 42 31 info@kreklau-‐hagedorn.de

SCHLINGELHOFF -‐ SCHLEIFMITTEL GMBH KIRCHSTRASSE 37 85131 POLLENFELD

+49 (0)8421 -‐ 901209 [email protected]

WEHA -‐ LUDWIG WERWEIN GMBH WIKINGER STRAßE 15 86343 KÖNIGSBRUNN

+49 (0)8231 – 6007 -‐ 0 [email protected]

AUSTRIA WEHA-‐STEINBEARBEITUNGSMASCH. VERTRIEBSGES. MBH LANGE GASSE 17 1080 Vienna

+43 1 4039340 +43 1 403934040 office@weha-‐wien.at

GEMBA G.M.B.H. POTTENDORFER STRASSE 511200 Vienna

+43 1 8158553 +43 1 815855322 [email protected]

BELGIUM AKEMI BENELUX BVBA – SPRL KROMSTRAAT 58 2520 RANST

+32 3 354 35 60 +32 3 354 35 61 [email protected]

BRAZIL DUPOX IND. E COM. PRODUTOS QUIMICOS PARA CONSTRUCAO LTDA. AV. MARECHAL CASTELO BRANCO NO 350, JARDIM TRES MARIAS CEP: 06790-‐070 TABOAO DA SERRA – SP

+55 11 41388010 +55 11 41388010 [email protected]

CHILE RAVENA S.A. AV. LAS CONDES AV. LAS CONDES 9507, 7591151 SANTIAGO

+5629526565 [email protected]

CHINA AKEMI BEIJING CO. LTD. ROOM 2704, UNIT1, BUILDING 2 YUELAN BAODI INT. AP. 39, NANMOFANG ROAD CHAOYANG DISTRICT 100022

+86 10 87794952 +86 10 87796163 [email protected]


CZECH REPUBLIC

FLADA S.r.o. STARY RYBNIK 123 351 34 SKALNA

+420 354673247 +420 354673247 [email protected]

DENMARK DIATOOL APS LUNDVEJ 16 8700 HORSENS

+4575 654577 +4575 75654970 [email protected]

ESTONIA KEMISTEIN OÜ BENSU2, VIT KÜLA HARKU VALD 76901

+372 6445160 +372 6445162 [email protected]

FRANCE DEGAMI SA 46-‐48 RUE DE CONFLANS 94220 CHARENTON-‐LE-‐PONT

+3301 43680017 +3301 43754998 contact @degami.fr

GREAT BRITAIN

APEX GRANGE LTD. ATTN: MR. JOHN BASS 14 LITTLE MUDELLS MUDELLS INDUSTRIAL CENTRE AL7 1EW WELWYN GARDEN CITY

+44 1707 338800 +44 1707 338811 [email protected]

C. R. LAURENCE OF EUROPE LTD. CHARLES BABBAGE AVENUE KINGSWAY BUSINESS PARK ROCHDALE LANCASHIRE OL16 4NW

+44 170 68 63 600 +44 170 86 98 60 [email protected] [email protected]

HUNGARY ANTIQUA KOFARAGO, GEP., SZERSZAM ES ANAYAGKERESKEDES KOZMA UTCA. 7 1108 BUDAPEST X

+361262 4365 +361262 4366 [email protected]

INDIA AKEMI TECHNOLOGY INDIA PVT LTD PLOT NO. 276,KANCHANAYAKANA HALLI SUB LAYOUT,PHASE 1, BOMMASANDRA INDUSTRIAL AREA JIGANI HOBLI, ANEKAL TALUK, 560100 BANGALORE -‐ KARNATAKA


IRAN PAVIR CO. (MINING & TRADING HOLDING ) HEAD OFFICE ADD.:BETWEEN #18TH&20 ST. MAHMOUDABAD INDUSTRIAL ZONE, ISFAHAN, IRAN

+98 31138014-‐85

+98 3801985-‐86

+98 311 38014-‐86 [email protected]

ITALY CEAM S.R.L. VIA DELLE LARE, 15 55045 PIETRASANTA (LU)

+390 584792449 +390 584284503 [email protected]


JAPAN TOUEI KENZAI INDUSTRIAL CO. LT 4-‐5-‐25 WAKAE NISHISHIN-‐MACHI HIGASHIOSAKA-‐CITY OSAKA

+81 6 67255236 +81 6 67255236 [email protected]

KOREA CPPM SERVICES INC. #105, SONGSAN BLDG, 279 DONGSOMUN-‐DONG-‐4KA, SUNGBUK-‐KU SEOUL 136-‐750

+822 9271114 +822 745 8114 [email protected]

NORWAY S. TANDBERG A/S P.O. BOX 63 NESVEIEN 13 1344 HASLUM

+4767 830600 +4767 830601 mail@s-‐tandberg.no

POLAND KONTIN-‐STONE Sp. z o.o. UL. HAUKE BOSAKA 11/9> 25-‐217 KIELCE

+48 41 3612254 +48 41 3611984 [email protected]

PORTUGAL PINHAO & IRMAO, LDA. FUNDACAO DE METAIS RUA DA TAPADINHA, NO. 53 APARTADO 458 4524-‐907 RIO MEAO

+351 256782679 +7 499 2598460 [email protected]

RUSSLAND N. SERVICE LTD. ZVENIGORODSKOE SHOSSE 28/1 123317 MOSCOW

+7 925 5858310 +351 256781053 [email protected]

SCHWEDEN MATEK AB N. ZINKGATAN 3 271 39 YSTAD

+46411 555725 +46411 555830 [email protected]

SLOVAKIA DANBIK s.r.o. KADNAROVA 51 83151 BRATISLAVA

+4211 44646262 +4211 44646263 [email protected]

SPAIN XABIER ALDANONDO DEL CAMPO C/JOSE MA SALABERRIA, 39 4 -‐ E 20010 DONOSTIA-‐SAN SEBASTIAN


SCHWITZERLAND

FERRONATO AG RIED 5420 EHRENDINGEN

+41 56 2040140 +41 56 2040149 [email protected]

UKRAINE LORI-‐R BUILDING 27, FLAT 55, VERKHOVNIY SOVIET AVENUE 02094 KIEV

+380 442915137 +380 445593065 office@lori-‐r.com

USA INNOCHEM LLC 4030 PLEASANTDALE ROAD SUITE F, DORAVILLE, GEORGIA 30340

+1 770 4098789 +1 770 4099096 [email protected]



MACHINERY: No machinery is required

TOOL: Specific DEKTON® putties.

putties.

REFERENCE: Dekton Colors Integra Match

Equivalency Integra Alt Match Equivalency

Ananké, Sirius, Domoos. Spectra (Mitre Joint)

Onyx 3243

Ariane, Zenit. Halo (Mitre Joint)

Winter White 3181

Danae Cygnus Pearl 2195 Halo (Deck seam) Pure White - 0190 Kadum (Deck seam) Vela Brown 2407 Kadum (Mitre Joint) Wenge - 3245 Vela Brown 2407 Keranium (Deck seam) Medea - 3186 Keranium (Mitre Joint) Brownstone 3244 Sirocco (Juntas) Fieldstone - 3246 Seashell - 3035 Sirocco (Mitre Joint) Strato (Mitre Joint)

Silver - 3129 Fieldstone - 3246

Spectra (Deck seam) Coal - 3242 Strato (Deck seam) Seashell - 3035 Fieldstone 3246

OBSERVATIONS: -‐ If nothing is indicated after a Dekton color, equivalencies can be used for mitre joints and deck seams. -‐Mastic only for INDOOR applications. Leave to polymerise for at least 30 minutes.

SUPPLIER: Integra Adhesives Inc. LOGO:

SALES CONTACT: Integra Adhesives Inc. North America 604-‐850-‐1321/1-‐888-‐862-‐6665 contact@integra-‐adhesives.com Integra Adhesives Europe B.V. +31 6 50 50 23 03 contact@integra-‐adhesives.com Integra Adhesives Inc., all other International markets 01.604.850.1321 contact@integra-‐adhesives.com

SECTION 5: LAMINATE


Prior to work -‐ Grind first the surfaces to be stuck with the diamond disk until fully flat. -‐Check that the surfaces are totally clean and dry before sticking. -‐ Surface and adhesive should both be at room temperature.. -‐ For a deck seam, apply masking tape on each side of the seam, back about 1.5mm from the joint (build up 2 to 3 layers of tape). Application -‐ Attach mixing tip to cartridge and dispense. -‐ Discard the first 5-‐10 ml to ensure Activator is present in mixture. Remember to purge with the cartridge pointing up. -‐ Apply a bead to the surfaces to be bonded. Clamp the surfaces together making sure to leave some adhesive in the joint. A gap of 1 mm or more will provide improved flexural and impact strength. Stick both pieces with the mixture and apply pressure for at least 30 minutes at 20-‐25°C for its polymerization. The adhesive is manageable during the first 10-‐15 minutes. -‐ For deck seam: after the bead has cured (30 minutes) it can be scraped flush with a razor blade. -‐ For mitre: after the bead has cured (30 minutes), the seam can be polished to enhance the color and smooth the surface.

!"#$$%&'(!)'*+&%"! !*,,%!)'*+&%"

*-$'!,.!/,(0!"#$%&'$()

1+23&4'(-!"*++,&-$(&.'"/0'1"$'2"%&3&'/"'.44,)1

*,,%5!5+)-&6&-"789:;<!"+0((&)1

('.'('42'!"

8=;789">*58"?<@;#;A*"8=;789"7*<*8"8=;789"5?A;@@;"8=;789"5:A*:;"8=;789"9*7BC"8=;789"98A*<?BC""8=;789"D8<?:E"F"E*#;"F"*A?*<8"F"*BA*"F"<*;<8"8=;789"7;C;;5"F"5=8@:A*"F"*<*<9G"F"5?A?B5"

,6"'(7+*&,4"5!!-"*2H)1&I)"&1"6.J"?<7;;A"$'2";B:7;;A"$++,&-$(&.'1K"#)$I)"(."+.,L%)J&1)"6.J"$(",)$1("MN"%&'0()1K"

"#$$%&'(5!""

OC@":)-'.,./P$"O0P%&-$Q"5K#K"

%,8,5!

"+%'"!2,4*+2*5!"9:;<!OC@":)-'.,./P$"O0P%&-$Q"5K#K"@F"*01&$1"C$J-HQ"+$J-),$"RST*"=K?K"#$"=.U,$T#$"8,&$'$Q"VMRWX"Y*#8<@?*":),K"ZM"[\["XM\M"]$3!"ZM"[\V"NZNM"C^I&,!"MR\"VZM"MW\"$/$J-&$_`%-K)1"

&<=>?<:=;@<:A5!!5))"$(($-H)2"($U,)"

"'2*&,4!B5!%+1&4+*'


PRIOR TO WORK -‐ Grind first the surfaces to be glued with the diamond disk until fully flat. -‐ Check that the glued surfaces are totally clean, dry and roughened before sticking. -‐ Surface and adhesive should both be at room temperature. -‐ For a deck seam, apply masking tape on each side of the seam, back about 1.5mm from the joint (build up 2 to 3 layers of tape).

APLICACIÓN -‐ EPODEK is a two component epoxy adhesive supplied in self-‐dosable cartridge, which requires no special tool. It can be easily applied with universal silicone gun. -‐ Discard the first 5-‐10 cm to ensure hardener is present in mixture. -‐ Apply adhesive on the surface to be bonded. Clamp the surfaces together making sure to leave some adhesive in the joint. A gap of 1 mm or more will provide improved flexural and impact strength. Stick both pieces with the mixture and apply pressure for at least 30 minutes at 20-‐25°C for its polymerization. -‐ The hardening process is accelerated by heat and delayed by cold. If you have infrared lamp oriented to the joint with EPODEK, it will significantly accelerates the drying time. -‐ For deck seam: after the product has cured (60 minutes) it can be scraped flush with a razor blade. -‐ For mitre: after the product has cured (60 minutes), the seam can be polished to enhance the color and smooth the surface.


ASIA QMC Tecnología Química, S.L. +34 96 272 5676 +34 617 496 686

+34 96 274 0906 [email protected]

BRASIL QMC BRASIL +34 608 369 889 +34 96 274 0906 [email protected]

EUROPE QMC Tecnología Química, S.L. +34 96 272 5676 +34 617 496 686


MEXICO QMC Mexico +52 871 7526 210 +52 871 7526 211 [email protected]

MIDDLE EAST

QMC Tecnología Química, S.L. +34 96 272 5676 +34 608 369 889


REST OF THE WORLD

QMC Tecnología Química, S.L. +34 96 272 5676 +34 96 274 0906 [email protected]

USA QMC Tecnología Química S.L. +34 96 272 5676 +34 617 496 686


Documents

SUPPLIER!DETAILS! TOOL!DETAILS! · 2015-07-24 · Quebec!JOB5 3E4! 137Junction! Street! 0018198767131! AJ! Bedard! [email protected] CDK!Stone!Pty.Ltd.! Australia! 456Freighter!Rd!