Upload
vuongnhan
View
215
Download
0
Embed Size (px)
Citation preview
Featuring Dual Duty XP® Paper Piecing thread and FreeSpirit Designer Essential Solids
Supplies• Coats Dual Duty XP® Paper Piecing thread• Lavender Sorbet - CSFSESS.SORBE• Purple Marbled - CBFS005.SPLAS• Violet Dahlia - CSFSESS.DAHLI• Hot Rose - CBFS004.HOTRO• Tropical Pink - CSFSESS.TROPI• Paper piecing thread• 4 copies of Block 4 foundation (page 3)
Additional Requirements• Sewing Machine• Basic Sewing Supplies• Printer
Technique: Paper piecing
Designed By: Cheryl A. Adam
Skill Level: Intermediate
Crafting Time: Longer Term
Finished size: 12" x 12" (30.48 x 30.48cm)
Milky Way Wall Hanging – Block 4
1 of 3 makeitcoats.comVersion 1.0
Milky Way Wall Hanging – Block 4
InstructionsNote: Cutting template on page 31. Roughly cut fabric to cover each labeled area of the
foundation; remember that you'll need four of each piece. For area 8 only, cut two pieces of CBFS004.HOTRO and two pieces of CSFSESS.FUSHI. Cut the fabric at least 1⁄2" (1.3cm)
2. larger on each side than the corresponding foundation area. Refer to the foundation labels for fabric placement.
3. Place fabric piece 1 right side up on the unmarked side of the paper foundation, making sure that it extends beyond the perimeter of foundation area 1 on all sides. It's helpful to hold the foundation up to a bright light so the fabric is visible from the printed side of the paper.
4. Place piece 2 on the unprinted side of the foundation, right side up, positioning it so that it covers area 2. Carefully flip piece 2 over onto piece 1 so that the fabrics are right sides together, making sure that fabric from both pieces extends at least 1⁄4" (.6cm) beyond the seamline. Pin the pieces in place. With the foundation printed-side up, sew on the line between areas 1 and 2.
5. Working on the unprinted side of the foundation, flip fabric 2 over so that its right side is facing up, and check again to make sure that fabric covers the entire foundation area. Flip fabric 2 back onto fabric 1 and trim the seam allowances to about 1⁄4" (.6cm). Smooth fabric 2 back over its foundation area and press.
6. Repeat steps 3 and 4 for the remaining foundation areas. When you have completed piecing the entire section, trim the perimeter seam allowances to 1⁄4" (.6cm). Make four quarter blocks, using each area-8 fabric for two of the quarter blocks. TIP: To stabilize the outer edges of each pieced section, stitch just outside the seamline around the section perimeter before trimming the foundations.
7. Following the block diagram above, sew the four quarter blocks together to make the block, matching intersecting seams. Carefully tear the paper from the back of the block and press.
Color Chart
4CSFSESS.SORBET
3CSFSESS.D
AHLI
2
CSFSESS.SORBET
7
CBFS005.SPLASH8 QTY - 2
CSFSESS.HOTRO
QTY - 2
CSFSESS.TROPI
5
CBFS004.HOTRO
6 CSFSESS.TROPI
1 CSFSESS.DAHLI
QTY - 2
CBFS004.HOTRO
QTY - 2
CSFSESS.TROPI
2 of 3 makeitcoats.comCopyright Coats © 2016 CS306-4 Version 1.0
Milky Way Wall Hanging – Block 4
4CSFSESS.SO
RBET
3
CSFSESS.DAHLI
2CSFSESS.SORBET
7
CBFS005.SPLASH
8 QTY - 2
CSFSESS.HOTRO
QTY - 2
CSFSESS.FUSHI
5CSFSESS.HOTRO6 CSFSESS.FUSHI
1 CSFSESS.DAH
LI
Test square1” x 1”
(2.54cm x 2.54cm
)
3 of 3 makeitcoats.comCopyright Coats © 2016 CS306-4 Version 1.0 3 of 3
*** Measure templates before cutting to confirm printing at 100%***