Upload
fabian-ortuzar
View
73
Download
0
Tags:
Embed Size (px)
Citation preview
SERVICE MANUAL
32″ LCD TV/DVDLD320SS8
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.
The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Laser Beam Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1Electrical Adjustment Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 How to Initialize the LCD TV/DVD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1Firmware Renewal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1 Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1Schematic Diagrams / CBA's and Test Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1System Control Timing Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1Lead Identifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-1Mechanical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-1Electrical Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-1
1-1 A74F0SP
SPECIFICATIONS
< LCD TV Section >
< TUNER / NTSC >ANT. Input ---------------------- 75 ohm Unbal., F type
< TUNER / ATSC >
< LCD PANEL >
< VIDEO >
< AUDIO >
All items are measured across 8 Ω load at speaker output terminal with L.P.F. / Video1 Input.
Description Condition Unit Nominal Limit
1. AFT Pull-in Range --- MHz ±2.3 ±2.1
2. Syncronizing Sens.TV.ch.4
CA.ch.31CA.ch.87
dBµdBµdBµ
---------
202023
Description Condition Unit Nominal Limit
1. Received Freq. Range (-28dBm) --- kHz --- ±100
2. ATSC Dynamic Range (min / max)ch.4ch.10ch.41
dBmdBmdBm
---------
-76/0-76/0-76/0
Description Condition Unit Nominal Limit
1. Native Pixel Resolusion HorizontalVertical
pixelspixels
1366768
------
2. Brightness (w / filter) --- cd/m2 320 ---
3. Viewing Angle HorizontalVertical
°°
-85 to 85-85 to 85
------
Description Condition Unit Nominal Limit
1. Over Scan HorizontalVertical
%%
66
6±56±5
2. Color Temperature---xy
°K 120000.2720.278
---±10%±10%
3. Resolution (composite video) HorizontalVertical
lineline
400350
------
Description Condition Unit Nominal Limit
1. Audio Output Power -6dB: Lch/Rch W 10.0/10.0 9.0/9.0
2. Audio Distortion 500mW: Lch/Rch % 0.5/0.5 2.0/2.0
3. Audio Freq. Response (NTSC) -6dB: Lch-6dB: Rch
HzHz
70 to 10 k70 to 10 k
------
1-2 A74F0SP
<DVD Section>< DVD >
Note: Nominal specifications represent the design specifications. All units should be able to approximate these. Some will exceed and some may drop slightly below these specifications. Limit specifications represent the absolute worst condition that still might be considered acceptable. In no case should a unit fail to meet limit specifications.
Description Condition Unit Nominal Limit
1. Horizontal Resolution (TDV-540 TIT.2 CHP.16) --- Line 350 330
2. Video S/N (TDV-540 TIT.2 CHP.6) --- dB 60 55
3. Audio Distortion (LPCM 48 kHz, W/LPF) (PTD 1-NOR TIT.1 CHP.1)
LR % 0.03 0.07
4. Audio freq. response (LPCM 48 kHz) (PTD 1-NOR TIT.1 CHP.5 -- 10)
L, 20 HzR, 20 HzL, 20 kHzR, 20 kHz
dB 0 +4/-5
5. Audio S/N (LPCM 48 kHz, W/LPF, A-WTD) (PTD 1-NOR TIT.1 CHP.1 -- 2)
LR dB 85 75
2-1 E7NLSP
LASER BEAM SAFETY PRECAUTIONS
This DVD player uses a pickup that emits a laser beam.
The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on. Do not look directly at the laser beam.
CAUTION: Use of controls and adjustments, or doing procedures other than those specified herein, may result in hazardous radiation exposure.
Location: Top of DVD mechanism.
Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin.
Drive Mechanism Assembly
Laser Beam Radiation
Laser Pickup
Turntable
LASER RADIATIONWHEN OPEN. DO NOT
STARE INTO BEAM.
CAUTION
3-1 LTVN_ISP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV Circuit1. Before returning an instrument to the
customer, always make a safety check of the entire instrument, including, but not limited to, the following items:
a. Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage.
b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover.
c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position.
d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test.
ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES.
2. Read and comply with all caution and safety-related notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel.
ALSO TEST WITHPLUG REVERSEDUSING ACADAPTER PLUGAS REQUIRED
TEST ALL EXPOSEDMETAL SURFACES
READING SHOULD NOT BE ABOVE 0.5 mA
EARTHGROUND
_
DEVICELEAKAGECURRENT
TESTER
+BEINGTESTED
3-2 LTVN_ISP
3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom.
4. Hot Chassis Warning -
a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection.
c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered.
5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.
7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
3-3 LTVN_ISP
Precautions during ServicingA. Parts identified by the # symbol are critical for
safety.Replace only with part number specified.
B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering.
F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp edged or pointed parts.
H. When a power cord has been replaced, check that 5~6 kg of force in any direction will not loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC supply outlet.
L. When installing parts or assembling the cabinet parts, be sure to use the proper screws and tighten certainly.
3-4 LTVN_ISP
Safety Check after ServicingExamine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)
Table 1: Ratings for selected area
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2. Leakage Current Test
Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.
Measuring Method: (Power ON)
Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table.
Table 2: Leakage current ratings for selected areas
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
AC Line Voltage Region Clearance Distance (d), (d’)
110 to 130 V U.S.A. or Canada
≥ 3.2 mm (0.126 inches)
AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
110 to 130 V U.S.A. or Canada
0.15 µF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA rms Exposed accessible
parts
Chassis or Secondary Conductor
Primary Circuit
Fig. 1
d' d
AC Voltmeter (High Impedance)
Exposed Accessible Part
B Earth Ground Power Cord Plug Prongs
Z
Fig. 2
4-1 TVDVDN_SN
STANDARD NOTES FOR SERVICING
Circuit Board Indications1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
2. For other ICs, pin 1 and every fifth pin are indicated as shown.
3. The 1st pin of every male connector is indicated as shown.
Instructions for Connectors1. When you connect or disconnect the FFC (Flexible
Foil Connector) cable, be sure to first disconnect the AC cord.
2. FFC (Flexible Foil Connector) cable should be inserted parallel into the connector, not at an angle.
Pb (Lead) Free SolderPb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder.
How to Remove / Install Flat Pack-IC
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)
2. Remove the flat pack-IC with tweezers while applying the hot air.
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.
2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape
Top View
Out In
Bottom ViewInput
5
10
Pin 1
Pin 1
FFC Cable
Connector
CBA
* Be careful to avoid a short circuit.
Pb free mark
Fig. S-1-1
4-2 TVDVDN_SN
around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)
3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.
With Soldering Iron:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Hot-airFlat Pack-ICDesolderingMachine
CBA
Flat Pack-IC
Tweezers
Masking Tape
Fig. S-1-2
Flat Pack-IC Desoldering Braid
Soldering Iron
Fig. S-1-3
Fine TipSoldering Iron
SharpPin
Fig. S-1-4
4-3 TVDVDN_SN
With Iron Wire:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.
3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.
4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.
2. Installation1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.
2. The “” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)
3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.
To Solid Mounting Point
Soldering Iron
Iron Wire
or
Hot Air Blower
Fig. S-1-5
Fine TipSoldering IronCBA
Flat Pack-ICTweezers
Fig. S-1-6
Example :
Pin 1 of the Flat Pack-ICis indicated by a " " mark. Fig. S-1-7
Presolder
CBA
Flat Pack-IC
Fig. S-1-8
4-4 TVDVDN_SN
Instructions for Handling Semi-conductorsElectrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.
<Incorrect>
CBA
Grounding Band
Conductive Sheet orCopper Plate
1MΩ
1MΩ
<Correct>
CBA
5-1 A74F0DC
CABINET DISASSEMBLY INSTRUCTIONS
1. Disassembly FlowchartThis flowchart indicates the disassembly steps for the cabinet parts, and the CBA in order to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were.
2. Disassembly Method
Step/Loc. No.
Part
Removal
Fig. No.
Remove/*Unhook/Unlock/Release/Unplug/Unclamp/
Desolder
Note
[1] Stand Base Plate D1 4(S-1), 6(S-2), 5(S-3) ---
[2] Stand Hinge D1 --------------- ---
[3] Stand Cover D1 --------------- ---
[4] Rear Cabinet D1 11(S-4), 4(S-5) ---
[5] DVD Cover D1 4(S-6) ---
[6] DVD Main CBA Unit
D2D6
(S-7), *CN201, *CN301, *CN401, *CN601,*CN801
1
[7] DVD Mechanism D2 4(S-8)
2345
[8] DVD Holder D2 4(S-9) ---
[2] Stand Hinge
[14] Jack Holder(A)
[23] IR SensorCBA
[22] LED CBA
[21] Function CBA
[3] Stand Cover
[15] Jack CBA
[10] Power Supply CBA
[19] T-CON CBA
[1] Stand Base Plate
[4] Rear Cabinet [5] DVD Cover
[9] Chassis Bracket
[16] Inverter CBA[24] Speaker Box(s)
[17] Junction CBA
[12] Shield Box [18] Panel Holder
[26] Front Cabinet
[13] Digital Main CBA Unit
[20] LCD Module Assembly
[11] Jack Holder(D)
[25] Speaker(s)
[6] DVD Main CBA Unit
[7] DVD Mechanism
[8] DVD Holder
[9] Chassis Bracket D3 8(S-10) ---
[10]Power Supply CBA
D3D6
4(S-11), *CN101B, *CN501, *CN801, *CN802, *CN3010, *CN3014 *CN3017
---
[11] Jack Holder(D) D3 (S-12), 2(S-13),
2(S-14), (N-1) ---
[12] Shield Box D3 6(S-15), *CN3001, Shield Plate ---
[13] Digital Main CBA Unit
D3D6
*CN3002, *CN3018, *CN3023 ---
[14] Jack Holder(A) D4 (S-16) ---
[15] Jack CBA D4D6 5(S-17) ---
[16] Inverter CBA
D4D6
6(S-18), *CN1050, *CN1100, *CN1150, *CN1200, *CN1250, *CN1300
---
[17] Junction CBA
D4D6 Desolder ---
[18] Panel Holder D4 8(S-19), 2(S-20) ---
[19] T-CON CBA
D5D6
6(S-21), Shield Plate, *CN9001, *CN9002, *CN9005
---
[20]LCD Module Assembly
D5 6(S-22) ---
[21] Function CBA
D5D6 3(S-23) ---
[22] LED CBA D5D6 2(S-24), *CN104 ---
[23] IR Sensor CBA
D5D6 2(S-25) ---
[24] Speaker Box(s) D5 4(S-26) ---
[25] Speaker(s) D5 8(S-27) ---
[26] Front Cabinet D5 --------------- ---
↓(1)
↓(2)
↓(3)
↓(4)
↓(5)
Step/Loc. No.
Part
Removal
Fig. No.
Remove/*Unhook/Unlock/Release/Unplug/Unclamp/
Desolder
Note
5-2 A74F0DC
Note:
(1) Order of steps in procedure. When reassembling, follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures.
(2) Parts to be removed or installed.
(3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, CN = Connector* = Unhook, Unlock, Release, Unplug, or Desoldere.g. 2(S-2) = two Screws (S-2), 2(L-2) = two Locking Tabs (L-2)
(5) Refer to the following "Reference Notes in the Table."
Reference Notes1. CAUTION 1: Electrostatic breakdown of the laser
diode in the optical system block may occur as a potential difference caused by electrostatic charge accumulated on cloth, human body etc., during unpacking or repair work.To avoid damage of pickup follow next procedures.
1) Short the three short lands of FPC cable with solder before removing the FFC cable (CN201) from it. If you disconnect the FFC cable (CN201), the laser diode of pickup will be destroyed. (Fig. D2)
2) Disconnect Connectors (CN301), (CN401), (CN601) and (CN801). Remove Screw (S-7) and remove the DVD Main CBA Unit. (Fig. D2)
2. Reassembly Notes of New DVD Mechanism:
a. To remove the Chassis Cover, remove two screws A as shown in Fig. D2.
b. To avoid damage of the pickup unit (laser diode), confirm that the three short lands (either of two places) are shorted out by soldering between them as shown in View A in Fig. D2.
c. Connect the FFC cables of the new DVD Mechanism to the three connectors (CN201, CN301, CN801) on the DVD Main CBA Unit.
d. After confirming that the FFC cables are securely connected to the three connectors, remove the solder from the three short lands. If the solder is not removed, the laser diode will not light and it will not be possible to read discs.
e. Insert the pin A on the Chassis Cover into the hole A on the Main Chassis as shown in Fig. D2. Then tighten two screws A to install the Chassis Cover.
3. CAUTION 2: When reassembling, confirm the FFC cable (CN201) is connected completely. Then remove the solder from the three short lands of FPC cable. (Fig. D2)
4. How to eject a disc in emergencyPress and hold [EJECT] on the unit for more than 5 seconds.
5. How to eject manually
1) Remove the Rear Cabinet and DVD Cover.
2) To remove the DVD Main CBA Unit, remove a screw (S-7) in Fig. D2. Do not disconnect connectors.
3) To remove the Chassis Cover, remove two screws A as shown in Fig. D2.
4) Remove a disc
5-3 A74F0DC
[4] Rear Cabinet
[3] Stand Cover
[2] Stand Hinge
[1] Stand Base Plate
(S-2)(S-2)
(S-3)
(S-3)
(S-4)
(S-5)
(S-4)
(S-5)
(S-4)
(S-1)
(S-1)
(S-4)
(S-4)
(S-1)
[5] DVD Cover
(S-6)
(S-4)
(S-1)
Fig. D1
5-4 A74F0DC
[7] DVD Mechanism
(S-9)[8] DVD Holder
(S-8)
(S-7)[6] DVD Main CBA Unit
A
Chassis Cover
Pin A
A
Hole A
Main Chassis
Remove two screws A, then short the three short lands by soldering as shown in View for A.
Screws A
View for A
Either of two places
FPC Cable
Fig. D2
5-5 A74F0DC
[11] Jack Holder(D)
[12] Shield Box
[13] Digital MainCBA Unit
[9] Chassis Bracket
(S-11)
(N-1)
(S-15)(S-10)
(S-10)
(S-10)
[10] Power Supply CBA
(S-11)
Shield Plate
(S-12)
(S-13)
(S-14)
(S-10)
(S-15)
Fig. D3
5-6 A74F0DC
[16] Inverter CBA
[14] Jack Holder (A)
(S-16)
(S-18)
(S-18)
(S-17)
[15] Jack CBA
[18] Panel Holder
(S-19)
(S-19)
(S-20)
(S-19)
(S-20)
(S-19)
[17] Junction CBA
Desolder
Fig. D4
5-7 A74F0DC
[20] LCD Module Assembly
[21] Function CBA
[23] IR SensorCBA
[25] Speaker
[22] LED CBA
[26] Front Cabinet
(S-22)
(S-24)
(S-23)
(S-25)
(S-26)
(S-21)
(S-21)
(S-21)
(S-22)
[24] Speaker Box
[24] Speaker Box
[25] Speaker
(S-26)
(S-27)
(S-27)
(S-27)
(S-27)
[19] T-CON CBA
Shield Plate
Fig. D5
5-8 A74F0DC
TV Cable Wiring Diagram
CN3010 CN3014
CL552A
CN301 CN302CN501
AC CORD
Function CBA
Power SupplyCBA
Digital MainCBA Unit
CN7501
CN601
Fig. D6
CN101B
CN801
CN3001
CN1050
CN1100
CN1150
CN1200
CN1250
CN1300
Inverter CBA
CN102
To LCD ModuleAssembly
Jack CBA
IR Sensor CBA LED CBA
CN802
CN3002CN3023 CN3018
ToSpeaker
CN3017
CN303
CN001
CL552B
CN552
JunctionCBA
T-CON CBA
CN9002 CN9001
CN9003
To LCD ModuleAssembly
CN9005
CN103CN104
CN601
CN301CN201
CN801
CN401
DVD Mechanism
DVD MainCBA Unit
CN202CN201
6-1 A74F0EA
ELECTRICAL ADJUSTMENT INSTRUCTIONS
General Note: “CBA” is abbreviation for “Circuit Board Assembly.”Note: Electrical adjustments are required after
replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.
Test Equipment Required1. DC Voltmeter
2. NTSC Pattern Generator (Color Bar W/White Window, Red Color, Dot Pattern, Gray Scale, Monoscope, Multi-Burst)
3. Remote control unit
4. Color Analyzer
How to make the Service remote control unit:Cut “A” portion of the attached remote control unit as shown in Fig. 1.
How to set up the service mode:
Service mode:1. Use the service remote control unit.
2. Turn the power on.
3. Press the service button on the service remote control unit. The following screen appears.
Fig. 1A
service button
Ver :Boot SystemPic Ver :
Picture :Submicon Ver :
*********************** Push 0 key Push 0 key********************************************** Push 0 key ******
"*" differs depending on the models.
6-2 A74F0EA
1. Purity Check ModeThis mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the Service mode.
2. Each time pressing [7] button on the service remote control unit, the display changes as follows.
2. VCOM Adjustment*This adjustment is required when reparing T-CON CBA.
Note: Use the service remote control unit
1. Operate the unit for more than 20 minutes.
2. Set the color analyzer and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
3. Enter the Service mode.
4. Press [3] button on the remote control unit.
5. Press [CH. o / p] buttons on the remote control unit so that the color analyzer value becomes minimum.
[7] button
Note:When entering this mode, the default setting is White mode.
Purity Check Mode
[7] button
Red mode
Green mode
Blue mode
White mode
[7] button
[7] button
Test Point Adj. Point
Screen [CH. o/p] buttons
M. EQ. Spec.
Color analyzer See below
Figure
Color Analyzer
It carries out in a darkroom.
L = 3 cm
Perpendicularity
6-3 A74F0EA
The following adjustment normally are not attempted in the field. Only when replacing the LCD Panel then adjust as a preparation.
3. White Balance Adjustment*This adjustment is required when reparing T-CON CBA.
Purpose: To mix red, green and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 20 minutes.
2. Input the White Purity.
3. Set the color analyzer to the CHROMA mode and bring the optical receptor to the center on the LCD-Panel surface after zero point calibration as shown above.Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
4. Enter the Service mode. Press [VOL. n] button on the remote control unit and select “C/D” mode.
5. [CUTOFF]Press [3] button to select “COB” for Blue Cutoff adjustment. Press [1] button to select “COR” for Red Cutoff adjustment.[DRIVE]Press [6] button to select “DB” for Blue Drive adjustment. Press [4] button to select “DR” for Red Drive adjustment.
6. In each color mode, press [CH. o / p] buttons to adjust the values of color.
7. Adjust Cutoff and Drive so that the color temperature becomes 12000K (x= 0.272 / y= 0.278 ±0.005).
Test Point Adj. Point Mode Input
Screen[CH. o/p]
buttons[RF/VIDEO1, 2]
C/D
White Purity (APL 70%)
or(APL 25%)
M. EQ. Spec.
Pattern Generator, Color analyzer
x= 0.272 ± 0.005y= 0.278 ± 0.005
Figure
Color Analyzer
It carries out in a darkroom.
L = 3 cm
Perpendicularity
INPUT: WHITE 70%, 25%
25%=25IRE 70%=70IRE
INPUT SIGNAL
7-1 A74F0INT
HOW TO INITIALIZE THE LCD TV/DVD
To put the program back at the factory-default, initialize the LCD TV/DVD using the following procedure.
< DVD Section >1. Press [1], [2], [3], [4], and [INFO] buttons on the
remote control unit in that order. Fig. g appears on the screen.
2. Press [CLEAR] button on the remote control unit. Fig. h appears on the screen.
When “OK” appears on the screen, the factorydefault will be set.
3. To exit this mode, press [CH. o / p] button to go toTV mode, or press [POWER] button to turn thepower off.
< LCD TV Section >1. Turn the power on.
2. To enter the service mode, press the service button on the service remote control unit. (Refer to page 6-1.)
- To cancel the service mode, press [POWER] button on the remote control unit.
3. Press [INFO] button on the remote control unit to initialize the LCD television.
4. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initialzing is complete.
MODEL : ******* Version : *.** Region : *
EXIT: SELECTEEPROM CLEAR : CLEAR
Fig. g
"*******" differs depending on the models.
MODEL : ******* Version : *.** Region : *
EEPROM CLEAR : OK
EXIT: SELECTEEPROM CLEAR : CLEAR
"*******" differs depending on the models.
Fig. h
8-1 A74F0FW
FIRMWARE RENEWAL MODE1. Turn the power on and press [EJECT] button on the
remote control unit to put the LCD TV/DVD intoDVD mode. Then remove the disc.
2. To put the LCD TV/DVD into F/W version up mode,press [9], [8], [7], [6], and [SEARCH MODE] but-tons on the remote control unit in that order.Fig. a appears on the screen.
3. Insert the disc for version up into the disc slot.4. The LCD TV/DVD enters the F/W version up mode
automatically. Fig. c appears on the screen. If youenter the F/W for different models, “Disc Error” willappear on the screen, then the disc will be ejectedautomatically.
The appearance shown in (*1) of Fig. c isdescribed as follows:
5. After programming is finished, the disc will beejected automatically. Fig. e appears on the screenand the checksum will be shown in (*2).
At this time, no button is available.6. Remove the disc.7. Unplug the AC cord from the AC outlet. Then plug it
again.8. Press [EJECT] button on the remote control unit to
put the LCD TV/DVD into DVD mode again.9. Press [1], [2], [3], [4], and [INFO] buttons on the
remote control unit in that order. Fig. g appears on the screen.
10.Press [CLEAR] button on the remote control unit. Fig. h appears on the screen.
When “OK” appears on the screen, the factorydefault will be set. Then the firmware renewalmode is complete.
11.To exit this mode, press [CH. o / p] button to go toTV mode, or press [POWER] button to turn thepower off.
F/W Version Up Mode Model No : *******VERSION : *.**
Please insert a DISCfor F/W Version Up.
EXIT: SELECT
"*******" differs depending on the models.
Fig. a Version Up Mode Screen
VERSION : ************.***Reading...
F/W Version Up Mode Model No : *******VERSION : *.**
Fig. c Programming Mode Screen
"*******" differ depending on the models.
(*1)
AppearanceNo. State
Reading... Sending files into the memory
Erasing... Erasing previous version data
Programming...
1
2
3 Writing new version data
VERSION : ************.***CompletedSUM : 7ABC
F/W Version Up Mode Model No : *******VERSION : *.**
"*******" differ depending on the models.
Fig. e Completed Program Mode Screen
(*2)
MODEL : ******* Version : *.** Region : *
EXIT: SELECTEEPROM CLEAR : CLEAR
Fig. g
"*******" differs depending on the models.
MODEL : ******* Version : *.** Region : *
EEPROM CLEAR : OK
EXIT: SELECTEEPROM CLEAR : CLEAR
"*******" differs depending on the models.
Fig. h
9-1
BLOCK DIAGRAMS < LCD TV Section >System Control Block Diagram
A74F0BLS
KE
Y-IN
24
3CN
102
KE
Y S
WIT
CH
KE
Y-IN
2K
EY-
IN1
KE
Y-IN
13
4K
EY
SW
ITC
H
IC30
06(S
UB
MIC
RO
CO
NT
RO
LLE
R)
IC30
15(M
AIN
MIC
RO
CO
NT
RO
LLE
R)
TU
3001
(TU
NE
R U
NIT
)
TX
D1
RX
D1
TX
DR
XD
CN
3002
19R
ES
ET
XO
UT
XIN
RE
SE
T
IC30
01
+3.
3V
X30
02
Q30
02
4MH
zO
SC
RE
SE
T
IC30
09
+3.
3V
DIG
ITA
L M
AIN
CB
A U
NIT
PO
WE
R S
UP
PLY
CB
A
JAC
K C
BA
IR S
EN
SO
R C
BA
LE
D C
BA
FU
NC
TIO
N C
BA
PO
WE
R S
UP
PLY
CB
A
PO
WE
R S
UP
PLY
CB
A
CN
001
RE
MO
TE
SE
NS
OR
RC
V89
1
AL+
3.3V
D10
2P
OW
ER
STA
ND
BY
D10
1LE
D2
66
CN
101B
RE
MO
TE
22
LED
17
7LE
D3
55
CN
302
Q10
2
LED
219
19
CN
3014
RE
MO
TE
88
CN
3014
SD
A6
6
CN
302
SC
L4
4 CN
3018
Q30
25
Q30
26S
DA
112
13
CN
7501
SC
L111
14
LED
1LE
D2
RE
MO
TE
LED
118
18
44C
N55
2C
L552
B
CN
202
77
66
PR
OT
EC
T1
4P
-ON
-H5
BAC
KLIG
HT-
PWM
7BA
CKL
IGH
T-O
NP
RO
TE
CT
1
BAC
KLIG
HT-
PWM
BAC
KLIG
HT-
ON
6
CN
3001
JUN
CT
ION
CB
A
55
P-O
N-H
17 31
14 15
32LE
D3
2020
LED
329 3 60 23 22
A5
C6
AF17
PO
WE
R-K
EY
PO
WE
R-K
EY
28E2
5
AD16
AU
DIO
-SE
L3A
UD
IO-S
EL2
AU
DIO
-SE
L1
AU
DIO
-SE
L3A
UD
IO-S
EL2
AU
DIO
-SE
L1TO
AU
DIO
-1B
LOC
K
DIA
GR
AM
A7B7C7
DV
D-A
UD
IO-M
UT
ED2
14 15I2
C-C
LK-T
UN
ER
I2C
-DAT
A-T
UN
ER
AE16
AF16
SC
LS
DA
SC
LS
DA
F26
F24
SC
L2S
DA
2AD
21E
EP
RO
M-W
P
XO
UT
XIN
X30
05B
18A
1825
.14M
Hz
OS
C
RE
SE
TA
D5
IC80
2(T
ON
E C
ON
TR
OL) S
CL
SD
A14 13
IC70
01(V
IDE
O/A
UD
IO S
ELE
CTO
R)
SC
LS
DA
25 27
IC30
26(M
TS
/SA
P A
UD
IO S
IGN
AL
PR
OC
ES
S)
SC
LS
DA
27 24
IC30
17(M
EM
OR
Y)
SC
L2S
DA
26 5
WP
7
IC30
14(D
IGIT
AL
SIG
NA
L P
RO
CE
SS
)
SC
L2S
DA
237 38
IC30
23(H
DM
I IN
TE
RFA
CE
)
SC
L2S
DA
228 27
IC30
04(G
AM
MA
CO
RR
EC
TIO
N)
SC
L2S
DA
244 43
DR
IVE
BU
FF
ER
BU
FF
ER
AU
DIO
-M
UT
EA
UD
IO-M
UT
EA
MP
-MU
TE
AM
P-S
TB
Y
V-C
OM
TO A
UD
IO-2
BLO
CK
D
IAG
RA
M
TO D
VD
DIG
ITA
LS
IGN
AL
PR
OC
ES
SB
LOC
K D
IAG
RA
M<
DV
D S
EC
TIO
N >
(CN
601)
TO
INV
ER
TE
RB
LOC
KD
IAG
RA
M(C
L552
A)
C24
AM
P-M
UT
EB2
4
BA
CK
LIG
HT-
PW
M
AM
P-S
TB
Y
AE21
BA
CK
LIG
HT-
ON
B26
DV
D-R
EM
OT
EAD
15
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
DIA
GR
AM
TO S
YS
TE
M
CO
NT
RO
L / S
ER
VO
B
LOC
K D
IAG
RA
M<
DV
D S
EC
TIO
N >
(CN
401)
27
BA
CK
LIG
HT-
ON
12P
RO
TE
CT
11
P-O
N-H
26
V-C
OM
5
DV
D-C
S16
DV
D-S
DAT
A11
DV
D-S
CLK
9
LED
-CO
NT
50D
VD
-DIS
C-O
UT
36D
VD
-DIS
C-I
N35
DV
D-P
WR
-RE
Q38
CN
303
CN
3017
44
DV
D-S
CLK
33
DVD-
AUDI
O-M
UTE
55
DV
D-C
S7
7D
VD
-SD
ATA
88
DV
D-R
EM
OT
E6
6D
VD
-PW
R-R
EQ
22
LED
-CO
NT
2121
DV
D-D
ISC
-OU
T20
20D
VD
-DIS
C-I
N
DVD-
AUDI
O-M
UTE
10
CN
104
CN
103
LED
31
1LE
D1
22
P-O
N-H
22
DVD-
MAIN
-POW
ER22
22
TO P
OW
ER
SU
PP
LYB
LOC
K D
IAG
RA
M
P-O
N-H
DV
D-M
AIN
-PO
WE
R
33D
VD
-MA
IN-P
OW
ER
21D
VD
-SC
LK22
DV
D-C
S24
DV
D-S
DAT
A25
DV
D-R
EM
OT
E26
DV
D-P
WR
-RE
Q2
LED
-CO
NT
3D
VD
-DIS
C-O
UT
23D
VD
-DIS
C-I
N
CN
201
9-2 A74F0BLV
Video Block DiagramV
IDE
O S
IGN
AL
IC30
23 (
HD
MI I
NT
ER
FAC
E)
IC70
01
(VID
EO
SE
LEC
TOR
)
IC30
29 (
ME
MO
RY
)
7 9 4 6 1 3 10 1216 1544 43 48 47 52 51 40 39
86 85 84 87
31 32B
UF
FE
RQ
3015
JK30
02
JK30
01
BU
FF
ER
Q30
14
5 6
HD
MI-
DAT
A
HD
MI-
IN1
HD
MI-
CLO
CK
DAT
A 0
(+)
DAT
A 0
(-)
DAT
A 1
(+)
DAT
A 1
(-)
DAT
A 2
(+)
DAT
A 2
(-)
CLO
CK
(+)
CLO
CK
(-)
JAC
K C
BA
DIG
ITA
L M
AIN
CB
A U
NIT
96 97
63 62 67 66 71 70 59 58
HD
MI
1.3
CO
RE
0
HD
MI
1.3
CO
RE
1
MU
XC
LAM
P
MU
XX
OR
MA
SK
MAT
RIX
HD
MI-
BC
LK
28.3
22M
Hz
OS
C
X30
06
X-I
NX
-OU
T
HD
MI-
LRC
LKH
DM
I-A
DAT
AA
DC
-OS
CLK
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
DIA
GR
AM
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
D
IAG
RA
M
110
144
AU
DIO
CO
DE
C
IIC I/F
SD
AS
CL
IC30
25 (
HD
MI M
EM
OR
Y)
5 6S
DA
SC
L
IC30
24 (
HD
MI M
EM
OR
Y)
IC30
14 (
DIG
ITA
L S
IGN
AL
PR
OC
ES
S)
5 6S
DA
SC
L
30 29B
UF
FE
RQ
3005
BU
FF
ER
Q30
06IIC I/F
AU
DIO
SIG
NA
L
7 9 4 6 1 3 10 1216 15H
DM
I-D
ATA
HD
MI-
IN2
HD
MI-
CLO
CK
DAT
A 0
(+)
DAT
A 0
(-)
DAT
A 1
(+)
DAT
A 1
(-)
DAT
A 2
(+)
DAT
A 2
(-)
CLO
CK
(+)
CLO
CK
(-)
43-5
0,55
-62,
76-8
3
JK77
02
JK77
06
VID
EO
-IN
1
S-V
IDE
O-I
N1
S-V
IDE
O-I
N2
VID
EO
-Y-I
N1
VID
EO
-Pb-
IN1
VID
EO
-Pr-
IN1
VID
EO
-Y-I
N2
VID
EO
-Pb-
IN2
VID
EO
-Pr-
IN2
VID
EO
-IN
2
34
21
YC
JK77
11
JK77
01
JK77
05
34
21
YC
JK77
13
5628 24 26 18 20 22
6 4 10 2 8 40 34 38 32 36 30
S-V
IDE
O-Y
9S
-VID
EO
-C8
VID
EO
-Y3
VID
EO
-Pb
5V
IDE
O-P
r6
CN
7501
CN
3018
VID
EO
VID
EO
S-V
IDE
O-Y
S-V
IDE
O-C
DV
I DAT
A(0
-23)
124 16 17 22 20 19
16
VID
EO
SE
LEC
TOR
9 6 11 25 22 27 20 18 15
A/D
CO
NVE
RTE
RC
SC
FO
RM
AT
D-S
UB
3 12 151 2R
ED
GR
EE
NB
LUE
DAT
AC
LOC
K
JK30
05
TO D
VD
DIG
ITA
LS
IGN
AL
PR
OC
ES
SB
LOC
K D
IAG
RA
M<
DV
D S
EC
TIO
N >
(CN
303)
CN
3017
DV
D-Y
10D
VD
-Pb
12D
VD
-Pr
13
WF
1W
F2
WF
3
WF
4W
F5
WF
6
9-3
Audio-1 Block Diagram
A74F0BLA1
JAC
K C
BA
DIG
ITA
L M
AIN
CB
A U
NIT
PO
WE
R S
UP
PLY
CB
A
AU
DIO
SIG
NA
LIC
7001
(AU
DIO
SE
LEC
TOR
)
AD
C-B
CLK
AD
C-L
RC
LKA
DC
-OS
CLK
AD
C-D
ATA
AU
DIO
(L)
-IN
1
AU
DIO
(R)
-IN
1
AU
DIO
(L)
-IN
2
AU
DIO
(R)
-IN
2
SIF
TU
3001
(TU
NE
R U
NIT
)F
L300
6
Q30
22
Q30
23
Q30
24
JK77
02
CO
MP
ON
EN
TA
UD
IO(L
)-I
N1
CO
MP
ON
EN
TA
UD
IO(R
)-I
N1
CO
MP
ON
EN
TA
UD
IO(L
)-I
N2
CO
MP
ON
EN
TA
UD
IO(R
)-I
N2
CN
3018
CN
7501
AU
DIO
(L)
1411
AU
DIO
(R)
1510
CN
201
DV
D-A
UD
IO(L
)9
DV
D-S
PD
IF13
DV
D-A
UD
IO(R
)11
CN
3017
CN
303
DV
D-A
UD
IO(L
)15
15D
VD
-SP
DIF
2323
DV
D-A
UD
IO(R
)17
17
PC
-AU
DIO
(L)
178
PC
-AU
DIO
(R)
187
IC30
21(A
UD
IO A
/D C
ON
VE
RT
ER
)
A/D
CO
NV
ER
TE
R
IC30
28(I
NP
UT
SE
LEC
T)
1 2
11 10 15 12
IC30
31(O
P A
MP
)IC30
26(M
TS
/SA
P A
UD
IO S
IGN
AL
PR
OC
ES
S) (L
-CH
)
TO
DIG
ITA
LS
IGN
AL
PR
OC
ES
SB
LOC
KD
IAG
RA
M
(R-C
H)
MT
S/S
AP
A
UD
IO S
IGN
AL
PR
OC
ES
S
30 2921
3S
AW
FIL
TE
R
JK77
04
HD
MI
AU
DIO
(L)-
IN
HD
MI
AU
DIO
(R)-
IN
JK30
03
AU
DIO
(L)
-IN
2
AU
DIO
(R)
-IN
2
JK77
06
PC
AU
DIO
-IN
TO DV
D D
IGIT
AL
SIG
NA
LP
RO
CE
SS
BLO
CK
DIA
GR
AM
< D
VD
SE
CT
ION
>(C
N60
1)
IC30
27(I
NP
UT
SE
LEC
T)
SW
CT
L
12 15 14 11
13
109
JK77
12
JK77
14
JK75
01
53 5145 44
49 47 54 52 50 48
2 671
13 12 1 2
14 15
SW
CT
L
1011
1 2 5 4
3
AU
DIO
SE
LEC
TOR
AU
DIO
SE
LEC
TOR
TO S
YS
TE
MC
ON
TR
OL
BLO
CK
DIA
GR
AM
AU
DIO
-SE
L1A
UD
IO-S
EL2
AU
DIO
-SE
L3
DV
D-S
PD
IF
Q30
08B
UF
FE
RQ
3007
BU
FF
ER
Q30
16B
UF
FE
R
Q30
17B
UF
FE
R
WF
7
WF
13
WF
12
WF
11
9-4
Audio-2 Block Diagram
A74F0BLA2
DIG
ITA
L M
AIN
CB
A U
NIT
PO
WE
R S
UP
PLY
CB
A
AU
DIO
SIG
NA
L
SP
802
SP
EA
KE
RL-
CH
CN
802
DR
IVE
CLN
802
SP
-P(L
)1
SP
-N(L
)2
SP
801
SP
EA
KE
RR
-CH
CN
801
CLN
801
SP
-P(R
)1
SP
-N(R
)2
CN
302
Q80
2
CN
3014
AU
DIO
(L)-
OU
T14
14A
UD
IO(R
)-O
UT
1616
AM
P-S
TB
Y9
9A
MP
-MU
TE
1010
Q30
29M
UTE
-ON
Q30
30M
UTE
-ON
AU
DIO
-MU
TE
AM
P-S
TB
YA
MP
-MU
TE
TO
SY
ST
EM
CO
NT
RO
LB
LOC
K D
IAG
RA
M
Q30
31D
RIV
E
IC30
20(O
P A
MP
)
IC80
2(T
ON
E C
ON
TR
OL)
2 671
AU
DIO
(L)
-OU
T
AU
DIO
(L)
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
DIA
GR
AM
AU
DIO
(R)
AU
DIO
(R)
-OU
T
JK30
03Q
3032
BU
FF
ER
Q30
33B
UF
FE
R
Q30
27B
UF
FE
R
Q30
28B
UF
FE
R
23 2
15 10
IC80
1(A
UD
IO P
OW
ER
AM
P)
44 1
3536 32 10 1431 139
PW
MP
WM
TON
E C
ON
TR
OL
TON
E C
ON
TR
OL
PW
M
SH
UT
DO
WN
MU
TE
CO
NT
RO
L
PW
MD
RIV
E
2122
9-5 A74F0BLD
TU
3001
IF1
21IF
220
DIG
ITA
L M
AIN
CB
A U
NIT
VID
EO
SIG
NA
LA
UD
IO S
IGN
AL
(TU
NE
R U
NIT
)
LC
D M
OD
UL
EA
SS
EM
BLY
SA
WF
ILT
ER
DE
MO
DU
-LAT
OR
MP
EG
DE
CO
DE
R
DAT
A(0
-7)
DAT
A(0
-15)
AD
DE
SS
(0-1
2)
TO V
IDE
OB
LOC
K D
IAG
RA
M
TO A
UD
IO-1
BLO
CK
DIA
GR
AM
IC30
15(D
IGIT
AL
SIG
NA
L P
RO
CE
SS
)
IF-A
GC
IF-A
GC
VID
EO
AU
DIO
(L)
AU
DIO
(R)
S-V
IDE
O-Y
S-V
IDE
O-C
DV
I DAT
A(0
-23)
18
VID
EO
(AN
ALO
G)
H-S
YN
C
V-S
YN
C
CLO
CK
V-C
OM
TO S
YS
TE
M C
ON
TR
OL
BLO
CK
DIA
GR
AM
4
IC30
16
IC30
18
IC30
19 (
ME
MO
RY
)BU
FF
ER
Q30
19
DIG
ITA
LS
IGN
AL
PR
OC
ES
S
AD
C-O
SC
LK
AD
C-O
SC
LK
HD
MI-
BC
LKH
DM
I-LR
CLK
HD
MI-
AD
ATA
DV
D-S
PD
IF-E
N
AD
C-D
ATA
DV
D-S
PD
IF
AD
C-B
CLK
AD
C-L
RC
LKA
UD
IOIN
TE
RFA
CE
AN
ALO
GS
W
TO V
IDE
OB
LOC
KD
IAG
RA
M
CLK
D-I
ND
-OU
TC
S
CLK
D-I
ND
-OU
TC
S
TO A
UD
IO-2
BLO
CK
DIA
GR
AM
A/D
CO
NV
ER
TE
R
CN
3023
IX-T
X0(
+)
21IX
-TX
0(-)
20IX
-TX
1(+
)18
IX-T
X1(
-)19
IX-T
X2(
+)
15IX
-TX
2(-)
16IX
-TX
3(+
)9
IX-T
X3(
-)10
IX-C
LK(+
)12
IX-C
LK(-
)13
IX-V
-CO
M23
A15
AF9
AD10
AF11
AD1
AE1
AD20
AD2
AD3
AE2
AF2
A25
AE3
A21
A22
A16
C5 A13
A9 C11
B16
A3 A2 B3 B1
AD6-9
,AD
11-14
,AE
6-9,
AE11
-14,
AF5-8
AF12
-15
D3,E
2,E3
,F1,
F2,G
1,H2
,H3
29-3
2,41
-44
T24-
26,U
24,
U26,
V24-
26,
W24
,W26
,Y24
-26
H24,
H25,
J26,
K24-
26,L
25,L
26,
M24
-26,
N24,
P24-
26,R
24
B1,B
9,C2
,C8,
D1,D
3,D7
,D9,
F1,F
9,G
2,G
8,H1
,H3,
H7,H
9M
2,M
3,M
7,M
8,N2
,N3,
N7,N
8,P2
,P3,
P7,P
8,R2
IC30
05(L
VD
S T
RA
NS
MIT
TE
R)
IC30
04(G
AM
MA
CO
RR
EC
TIO
N)
27 28 31
47 48 45 46 41 42 37 38 39 40
19 20 17 18 14 15 9 10 12 13
57 56 59 58 63 62 67 66 65 64
TT
LPA
RA
LLE
LTO S
ER
IAL
CO
NV
ER
T.
PLL
LVD
SR
XLV
DS
TX
GA
MM
AC
OR
R.
2-4,6-
8,10
-12,14
-16,
18-20
,22-24
,50
-52,54
-56
H1,J1
-3,K1
-3,L1
-3,M1
,M2,
P1-3,
R1-3,
T1-3,
U1-3
(SD
RA
M)
(FLA
SH
ME
MO
RY
)
6 5 2 1
Q30
01D
RIV
E
DIG
ITA
L A
UD
IO-O
UT
(CO
AX
IAL)
JK30
04B
UF
FE
RQ
3018
IC30
12(B
UF
FE
R)
42
1
IC30
10(B
UF
FE
R)
42
1
X24
2-S
PD
IF-E
NAD
19
Digital Signal Process Block Diagram
9-6
Inverter Block Diagram
A74F0BLINV
BA
CK
LIG
HT
1 2 1 2 1 2 1 2 1 2 1 2
INV
ER
TE
R C
BA
LC
D M
OD
UL
E
CN
1050
CN
1100
CN
1150
CN
1200
CN
1250
CN
1300
IS VS
OV
P
CL5
52A
P
-ON
-H5
BAC
KLI
GH
T-P
WM
7B
ACK
LIG
HT-
ON
6P
RO
TE
CT
14
IC15
00 (C
OM
PARA
TOR)
IC15
50 (C
OM
PARA
TOR)
V-R
EF
Q10
20
DR
IVE
21
3 13 126 5
147
IC10
01
(IN
VE
RT
ER
CO
NT
RO
L)
IC50
1 (P
OW
ER
CO
NT
RO
L)
21
3 13 12 9 10 6 5
14 8 7
9 108
V-R
EF
TO
SY
ST
EM
CO
NT
RO
LB
LOC
K
DIA
GR
AM
(CL5
52B
)
VC
C
VC
C
4 4Q
1002
Q10
03
Q10
01
T10
50Q
1100
,Q
1101
Q11
02,
Q11
03
Q12
50,
Q12
51
Q12
52,
Q12
53
3 1 4
78 6 5
2 T11
00
3 1 4
78 6 5
2 T11
50
3 1 4
78 6 5
2 T12
00
T50
1TO
P
OW
ER
PU
PP
LYB
LOC
K
DIA
GR
AM
AC
LH
OT-
GN
D
3 1 4
78 6 5
2 T12
50
3 1 4
78 6 5
2 T13
00
3 1 4
78 6 5
2
DR
IVE
DR
IVE
DR
IVE
DR
IVE
INV
ER
TE
RC
ON
TR
OL
10 11 14 15
2 3 4 5 7 84 5 23 2
14 3
2
D55
7
Q55
1
Q55
2
IC50
9
14 3
2
IC51
0
Q50
1
Q50
2
SH
UN
TR
EG
SW
25 3
7 1
POW
ERCO
NTRO
L
13
1119
DR
IVE
LOG
ICLO
GIC
DR
IVE
DR
IVE
BA
CK
LIG
HT
BA
CK
LIG
HT
BA
CK
LIG
HT
BA
CK
LIG
HT
BA
CK
LIG
HT
Q17
01
HO
T
HO
T C
IRC
UIT
. BE
CA
RE
FU
L.
12 16
NO
TE
:T
he v
olta
ge fo
r pa
rts
in h
ot c
ircui
t is
mea
sure
d us
ing
hot G
ND
as
a co
mm
on te
rmin
al.
9-7
Power Supply Block Diagram
A74F0BLP
HO
T
HO
T
CO
LD
PO
WE
R S
UP
PLY
CB
A
INV
ER
TE
R C
BA
HO
T C
IRC
UIT
. BE
CA
RE
FU
L.
TO D
IGIT
AL
MA
IN C
BA
UN
IT(C
N30
10)
Q60
2S
WIT
CH
ING
CO
NT
RO
L
14 3
2
IC60
3
IC63
7
T60
1C
N60
1
TO IN
VE
RT
ER
BLO
CK
DIA
GR
AM
CN
501
4
+3.
3VR
EG
HO
T-G
ND
3A
CL
131
P-O
N+
9V8
P-O
N+
5V6,
7
+2.
5V14
+4V
10-1
2
+15
V18
+2.
5V16
AL+
3.3V
4+
5V/+
12V
-LC
D2,
3
+35
V20
F50
14A
/125
VLI
NE
FIL
TE
R
L503
AC
501
AC
CO
RD
LIN
EF
ILT
ER
L502
BR
IDG
ER
EC
TIF
IER
AC
LH
OT-
GN
D
D50
2 -
D50
5
4A 1
25V
2
16 15 10 14 9 13 12 1176
SH
UN
TR
EG
Q60
1S
WIT
CH
ING
Q80
1A
MP
+13
V
P-O
N+
9V
CN
301
+9V
RE
G
Q63
9,Q
640
Q64
1
Q63
8
Q63
7
Q64
4
JS63
2
Q63
5
Q63
3
JS66
1Q
630
Q63
6
SW
+13
V
Q63
2
Q63
1
Q64
3
23
JS61
2
Q65
0,Q
651
Q65
2
SW
+5V
IC16
01+
1.2V
RE
G.
DV
D M
AIN
C
BA
UN
IT
CN
202
CN
401
1A
L+3.
3V1
AL+
3.3V
4-5
EV
+1.
2V4-
5E
V+
1.2V
6-8
EV
+3.
3V6-
8E
V+
3.3V
DV
D-O
N+3
.3V
DV
D-O
N+5
VE
V+
10V
9D
VD
-ON
+3.3
V9
10D
VD
-ON
+5V
10
11~
12E
V+
9V11
~12
11-1
2E
V+
10V
11
-12
Q16
04
Q16
01 Q16
02
P-O
N-H
TO
SY
ST
EM
CO
NT
RO
LB
LOC
K
DIA
GR
AM
SH
UN
T R
EG
IC16
03
+3.
3V R
EG
Q16
03
SH
UN
T R
EG
IC16
02
+3.
3V R
EG
DV
D-M
AIN
-PO
WE
RT
O S
YS
TE
MC
ON
TR
OL
BLO
CK
D
IAG
RA
M
CA
UT
ION
!F
ixed
vol
tage
(or
Aut
o vo
ltage
sel
ecta
ble)
pow
er s
uppl
y ci
rcui
t is
used
in th
is u
nit.
If M
ain
Fus
e (F
501)
is b
low
n , c
heck
to s
ee th
at a
ll co
mpo
nent
s in
the
pow
er s
uppl
yci
rcui
t are
not
def
ectiv
e be
fore
you
con
nect
the
AC
plu
g to
the
AC
pow
er s
uppl
y.O
ther
wis
e it
may
cau
se s
ome
com
pone
nts
in th
e po
wer
sup
ply
circ
uit t
o fa
il.
For
con
tinue
d pr
otec
tion
agai
nst r
isk
of fi
re,
repl
ace
only
with
sam
e ty
pe 4
A, 1
25V
fuse
.C
AU
TIO
N !
:
AT
TE
NT
ION
: U
tilis
er u
n fu
sibl
e de
rec
hang
e de
mêm
e ty
pe d
e 4
A, 1
25V
.4A
/125
V
NO
TE
:T
he v
olta
ge fo
r pa
rts
in h
ot c
ircui
t is
mea
sure
d us
ing
hot G
ND
as
a co
mm
on te
rmin
al.
9-8
BLOCK DIAGRAMS < DVD Section >System Control / Servo Block Diagram
A74F0BLSD
IC30
1(S
ER
VO
DR
IVE
)
CN
301
M
SLE
D
MO
TO
R
M
SP
IND
LE
MO
TO
R
IC10
1(M
ICR
O C
ON
TR
OLL
ER
)
+ -+ -
+ -+ -
+ -+ - + -
SLE
DM
OTO
RD
RIV
E
FO
CU
SA
CT
UAT
OR
DR
IVE
SP
IND
LEM
OTO
RD
RIV
E
TR
AC
KIN
GA
CT
UAT
OR
DR
IVE
126
LOA
D-D
ISC
SLD
67
SP
DL
66
TR
AC
KIN
GD
RIV
E
127
FO
CU
S D
RIV
EF
S(+
)F
S(-
)
TS
(+)
TS
(-)
LOA
D-D
ISC
1S
P(+
)2
SP
(-)
6LO
AD
-DIS
C3
GN
D4
SL(
-)5
SL(
+)
VR
EF
RE
SE
T70
RE
SE
T
IC46
2
13
+3.
3V
IC20
2(O
P A
MP
)
15 16 14 13 12 11 17 182364 531 225 2427 26
121
SP
-RO
T
124
FD
-OF
ST
123
TD
-OF
ST
RE
SE
T
IC46
1
21
+3.
3V
TO D
VD
DIG
ITA
LS
IGN
AL
PR
OC
ES
SB
LOC
K D
IAG
RA
M
DR
IVE
CB
A
DV
D M
AIN
CB
A U
NIT
CN
401
DVD-
DISC
-OUT
3LE
D-C
ON
T2
122
SL-
AD
S
DIS
C-I
N
12 6
753
3D
VD
-DIS
C-IN
32
DVD-
DISC
-OUT
2CN
801
CN
5001
DIS
C-O
UT
SE
NS
OR
CB
A
+3.
3V
1LE
D-P
OW
ER
1
Q80
4
63D
VD
-DIS
C-I
ND
VD
-DIS
C-O
UT
TO SY
ST
EM
CO
NT
RO
LB
LOC
K D
IAG
RA
M<
LC
D T
V S
EC
TIO
N >
(CN
202)
53D
VD
-SC
LK54
DV
D-C
S
49D
VD
-RE
MO
TE
DV
D-P
WR
-RE
Q
56D
VD
-SD
ATA
DVD
-REM
OTE
25D
VD
-SD
ATA
24D
VD
-CS
22D
VD
-SC
LK21
DV
D-D
ISC
-IN
23
6165
DVD-
PWR-
REQ
2677
1
NO
TE
:
Eith
er IC
461
or IC
462
is u
sed
for
DV
D M
AIN
CB
A U
NIT
.
9-9
DVD Digital Signal Process Block Diagram
A74F0BLDD
C16
D18
A17
B15
DV
D-L
D8
CD
-LD
10
PD
-MO
NI
7
FS
(+)
2F
S(-
)3
TS
(+)
1T
S(-
)4C
N20
1
CN
201
CN
201
IC20
1(S
W)
IC10
1(M
ICR
O C
ON
TR
OLL
ER
)
FS
FS
(+)
CD
/DV
D
FS
(-)
TS
(+)
TS
(-)
TS
DE
TE
CTO
R
CD
/DV
D19
Q25
1,Q
252
CDDV
D
AM
P
Q25
3,Q
254
AM
P
4
13
6
GN
D(D
VD-P
D)
6G
ND
(CD
-PD
)5
GN
D(L
D)
9
RF
SIG
NA
LP
RO
CE
SS
CIR
CU
IT
DV
D/C
DF
OR
MAT
TE
R
AU
DIO
I/F
VID
EO
I/FN
TS
C/P
AL
EN
CO
DE
R
DM
A
BC
U
INS
T.R
OM
32B
ITC
PU
DAT
AR
AM
INT
ER
RU
PT
CO
NT
RO
LLE
RW
ATC
H D
OG
TIM
ER
CP
UI/F
TIM
ER
DE
CO
DE
RI/F
CP
UI/F
RE
AD
ME
MO
RY
DAT
AR
AM
DS
PD
EC
OD
ER
I/O PR
OC
ES
SO
R
INS
T.R
OM
DAT
AR
AM
INS
T.R
OM
SE
RIA
L
D/A
GE
NE
RA
LI/O IN
TE
RR
UP
TC
ON
TR
OLL
ER
TIM
ER
WAT
CH
DO
GT
IME
R
RE
MO
TE
CO
NT
RO
L
32B
IT C
PU
ST
RE
AM
I/F
EX
TE
RN
AL
ME
MO
RY
I/FS
DR
AM
EC
C
UM
AC
100
115
116
113
114
106
104
105
103
62
DE
BU
G
BC
U
INS
TC
AC
HE
DAT
AC
AC
HE
D/A
D/A
131
139
Y Pb
152
SD
RA
M A
DD
RE
SS
(0-1
0)
IC10
3(F
LAS
H R
OM
)
FLA
SH
RO
M
29 36 38 45
~ ~
FD
Q (
0-15
)
~
1 9 16 25 48
~
FAD
R (
0-19
)
SD
RA
M D
ATA
(0-1
5)
PIC
K-U
PU
NIT
TO S
YS
TE
M
CO
NT
RO
L/S
ER
VO
BLO
CK
DIA
GR
AM
DV
D M
AIN
CB
A U
NIT
TO V
IDE
OB
LOC
K
DIA
GR
AM
TO A
UD
IO-1
BLO
CK
DIA
GR
AM
IC50
3(S
DR
AM
)
SD
RA
M D
ATA
(0-1
5)
SD
RA
M A
DD
RE
SS
(0-1
0)19
4
209~
2 13 42 53
~ ~22 26 29 34
~ ~
159
178~
99 98 97
21~
3034
~42
212
1~4
7~14
17~
1821
5~21
6
AU
DIO
D/A
CO
NV
ER
TE
R
< L
CD
TV
SE
CT
ION
>(C
N20
1)
< L
CD
TV
SE
CT
ION
>(C
N20
1)
< L
CD
TV
S
EC
TIO
N >
(CN
3017
)
VID
EO
SIG
NA
LA
UD
IO S
IGN
AL
CN
201
CN
601 8
DV
D-Y
56
DV
D-P
b3
4D
VD
-Pr
1
144
151
146
13DV
D-AU
DIO
-MUT
E
14D
VD
-AU
DIO
(R)
12D
VD
-AU
DIO
(L)
16D
VD
-SP
DIF
CN
601
CN
601
PO
WE
R S
UP
PLY
CB
A
TO S
YS
TE
M
CO
NT
RO
LB
LOC
K D
IAG
RA
M
WF
8
WF
9
WF
10
129
Pr
10D
VD
-Y12
DV
D-P
b13
DV
D-P
r
CN
303
10-1 A74F0_SC
SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.
Notes:1. Do not use the part number shown on these
drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared.
2. All resistance values are indicated in ohms (K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4. All capacitance values are indicated in µF (P = 10-6 µF).
5. All voltages are DC voltages unless otherwise specified.
10-2 A74F0_SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES:
1. CAUTION:CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F501) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
3. Note:1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.
4. Voltage indications for PLAY and STOP modes on the schematics are as shown below:
5. How to read converged lines
6. Test Point Information
2 31 5.0< 0 >
TV mode DVD mode
< TV Section > Unit: Volts
5.0
The same voltage forboth TV & DVD modes
Unit: Volts
Indicates that the voltageis not consistent here.
2 31 5.0(2.5)
PLAY mode STOP mode5.0
The same voltage forboth PLAY & STOP modes
Unit: Volts
Indicates that the voltageis not consistent here.
< DVD Section >
3
2
1
A B C D
1-B1
1-D3
AREA D3
AREA B1
1-D3
Distinction AreaLine Number (1 to 3 digits)
Examples:1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
10-3 A74F0SCP1
Power Supply 1/3 Schematic Diagram < LCD TV Section >
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
CN301
1 02 12.33 12.34 3.45 06 5.17 5.18 9.29 010 5.211 5.212 5.213 014 3.315 016 2.817 018 15.719 020 33.1
21 0
22 3.0
23 1.3
VOLTAGE CHART
Pin No. Voltage
10-4 A74F0SCP2
Power Supply 2/3 Schematic Diagram < LCD TV Section >
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
CN302
1 ---2 3.13 04 3.45 06 3.47 08 3.49 0.110 3.311 ---12 3.413 014 6.315 016 6.317 018 3.319 0.920 0.2
21 ---
22 0
23 0
VOLTAGE CHART
Pin No. Voltage
10-5 A74F0SCP3
Power Supply 3/3 Schematic Diagram < LCD TV Section >
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
CN303
1 02 3.03 04 0.35 0.26 3.27 0.38 09 010 011 012 013 014 015 016 017 018 019 3.420 2.6
21 2.6
22 0
23 0
VOLTAGE CHART
Pin No. Voltage
10-6 A74F0SCINV
Inverter & Junction Schematic Diagram < LCD TV Section >
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F501) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire, replace only with same type 4 A, 125V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.4A/125V
CN552
1 02 3.33 0.14 3.25 3.06 3.37 3.48 0
VOLTAGE CHART
Pin No. Voltage
10-7 A74F0SCJ
Jack Schematic Diagram < LCD TV Section >
CN7501
1 2.62 03 2.34 05 2.36 07 08 09 010 011 5.012 5.013 014 2.515 2.516 017 2.518 2.519 020 ---21 022 5.023 024 9.1
VOLTAGE CHART
Pin No. Voltage
10-8 A74F0SCF
Function Schematic Diagram < LCD TV Section >
CN102
1 ---2 ---3 3.44 3.45 ---6 0
VOLTAGE CHART
Pin No. Voltage
10-9 A74F0SCIR
IR Sensor & LED Schematic Diagram < LCD TV Section >
10-10 A74F0SCD1
Digital Main 1/10 Schematic Diagram < LCD TV Section >
10-11 A74F0SCD2
Digital Main 2/10 Schematic Diagram < LCD TV Section >1 NOTE:The order of pins shown in this diagram is different from that of actual IC3015.IC3015 is divided into four and shown as IC3015 (1/4) ~ IC3015 (4/4) in this Digital Main Schematic Diagram Section.
10-12
Digital Main 3/10 Schematic Diagram < LCD TV Section >
A74F0SCD3
1 NOTE:The order of pins shown in this diagram is different from that of actual IC3015.IC3015 is divided into four and shown as IC3015 (1/4) ~ IC3015 (4/4) in this Digital Main Schematic Diagram Section.
10-13
Digital Main 4/10 Schematic Diagram < LCD TV Section >
A74F0SCD4
1 NOTE:The order of pins shown in this diagram is different from that of actual IC3015.IC3015 is divided into four and shown as IC3015 (1/4) ~ IC3015 (4/4) in this Digital Main Schematic Diagram Section.
10-14
Digital Main 5/10 Schematic Diagram < LCD TV Section >
A74F0SCD5
1 NOTE:The order of pins shown in this diagram is different from that of actual IC3015.IC3015 is divided into four and shown as IC3015 (1/4) ~ IC3015 (4/4) in this Digital Main Schematic Diagram Section.
10-15
Digital Main 6/10 Schematic Diagram < LCD TV Section >
A74F0SCD6
10-16
Digital Main 7/10 Schematic Diagram < LCD TV Section >
A74F0SCD7
10-17
Digital Main 8/10 Schematic Diagram < LCD TV Section >
A74F0SCD8
10-18
Digital Main 9/10 Schematic Diagram < LCD TV Section >
A74F0SCD9
10-19
Digital Main 10/10 Schematic Diagram < LCD TV Section >
A74F0SCD10
10-20 A74F0SCDV1
DVD Main 1/3 Schematic Diagram < DVD Section >
1 NOTE: Either IC461 or IC462 is used for DVD MAIN CBA UNIT.
10-21 A74F0SCDV2
DVD Main 2/3 Schematic Diagram < DVD Section >
10-22 A74F0SCDV3
DVD Main 3/3 Schematic Diagram < DVD Section >
10-23
Power Supply CBA Top View
BA71F0F01022-1
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
Because a hot chassis ground is present in the powersupply circuit, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly,when troubleshooting this type power supplycircuit, a variable isolation transformer is required.
10-24
PIN 13 OFCN201
WF13
PIN 11 OFCN201
WF12
PIN 9 OFCN201
WF11
PIN 5 OFCN201
WF8
PIN 3 OFCN201
WF9
PIN 1 OFCN201
WF10
Power Supply CBA Bottom View
BA71F0F01022-1
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
Because a hot chassis ground is present in the powersupply circuit, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly,when troubleshooting this type power supplycircuit, a variable isolation transformer is required.
10-25 BA71F0F01041
Inverter CBA Top View
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F501) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire, replace only with same type 4 A, 125V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.4A/125V
Because a hot chassis ground is present in the powersupply circuit, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly,when troubleshooting this type power supplycircuit, a variable isolation transformer is required.
10-26
Inverter CBA Bottom View
BA71F0F01041
NOTE:The voltage for parts in hot circuit is measured usinghot GND as a common terminal.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.If Main Fuse (F501) is blown , check to see that all components in the power supplycircuit are not defective before you connect the AC plug to the AC power supply.Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire, replace only with same type 4 A, 125V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 4A, 125V.4A/125V
Because a hot chassis ground is present in the powersupply circuit, an isolation transformer must be used.Also, in order to have the ability to increase the inputslowly,when troubleshooting this type power supplycircuit, a variable isolation transformer is required.
10-27
Jack CBA Top View
BA71F0F01022-4
10-28
PIN 9 OFCN7501
WF2
PIN 3 OFCN7501
WF4PIN1 OFCN7501
WF1
PIN 6 OFCN7501
WF6PIN 8 OFCN7501
WF3
PIN 5 OFCN7501
WF5
PIN 14 OFCN7501
WF7
Jack CBA Bottom View
BA71F0F01022-4
10-29
Function CBA Top View
Function CBA Bottom View
BA71F0F01022-2
10-30
BA71F0F01041
Junction CBA Top & Bottom View
IR Sensor CBA Top View
IR Sensor CBA Bottom View
BA71F0F01022-3
LED CBA Top & Bottom View
BA71F0F01022-5
WAVEFORMS < LCD TV SECTION >
A74F0WF11-1
Input: NTSC Color Bar Signal (with 1kHz Audio Signal)
WF1 ~ WF7 = Waveforms to be observed atWaveform check points.(Shown in Schematic Diagram.)
CVBS 0.2V 20µs
WF1 Pin 1 of CN7501
S-VIDEO-Y 0.2V
WF2 Pin 9 of CN7501
20µs
S-VIDEO-C 0.2V
WF3 Pin 8 of CN7501
20µs AUDIO 1V 0.5ms
WF7 Pin 14 of CN7501
VIDEO-Pr 0.2V 20µs
Pin 6 of CN7501WF6
VIDEO-Pb 0.2V 20µs
Pin 5 of CN7501WF5
VIDEO-Y 0.2V 20µs
Pin 3 of CN7501WF4
WAVEFORMS < DVD SECTION >
A74F0WF11-2
Input: NTSC Color Bar Signal (with 1kHz Audio Signal) DVD Video (Power on (Stop) MODE)
WF8 ~ WF13 = Waveforms to be observed atWaveform check points.(Shown in Schematic Diagram.)
WF8 Pin 5 of CN201
WF9 Pin 3 of CN201
WF11 Pin 9 of CN201
Pin 13 of CN201WF13
Pin 11 of CN201WF12
20µs0.5VDVD-Y
DVD-Pb 0.5V 20µs
WF10 Pin 1 of CN201
DVD-Pr 0.5V 20µs
DVD-AUDIO(L) 0.5V 0.5ms
DVD-AUDIO(R) 0.5V 0.5ms
DVD-SPDIF 1V 0.1µs
WIRING DIAGRAM < LCD TV SECTION >
A74F0WI12-1
INV
ER
TE
R
CB
A
FU
NC
TIO
NC
BA
TU
3001
TU
NE
R U
NIT
HD
MI-
AU
DIO
(L)-
IN
HD
MI-
AU
DIO
(R)-
IN
AU
DIO
(L)
-OU
T
AU
DIO
(R)
-OU
T
AC
501
AC
CO
RD
PO
WE
R S
UP
PLY
CB
A
DIG
ITA
L M
AIN
CB
A U
NIT
D-S
UB
CO
NN
EC
TO
R
HD
MI-
CO
NN
EC
TO
R-1
HD
MI-
CO
NN
EC
TO
R-2
IR
SE
NS
OR
C
BA
JUN
CT
ION
CB
A1 32 54 76 8 9 10 131211 14 15 1716 1918 2120 22 23
P-O
N+
9V
GN
DN
UG
ND
PC
-AU
DIO
(R)
PC
-AU
DIO
(L)
AU
DIO
(L)
GN
DA
UD
IO(R
)
GN
D
GN
D
SD
A1
SC
L1
S-V
IDE
O-Y
VID
EO
-Pr
S-V
IDE
O-C
GN
D
VID
EO
-Pb
GN
D
GN
D24
VID
EO
VID
EO
-Y
CN
3018
GN
DD
+5V
CN
7501 15 39 7 24681014 1218 16 111315171923 21 202224
CN
552
CN
3001
11
GN
D
33
PR
OTE
CT2
(NU
)2
2P
RO
TEC
T3(N
U)
44
PR
OT
EC
T1
55
P-O
N-H
77
BACK
LIG
HT-P
WM
66
BAC
KLI
GH
T-O
N
88
GN
D
CN
3023
1D
+5V
/+12
V-LC
DD
+5V
/+12
V-LC
DD
+5V
/+12
V-LC
DD
+5V
/+12
V-LC
DD
+5V
/+12
V-LC
D
2 3 4 5 6G
ND
GN
DG
ND
7 8 9IX
-TX
3(+
)10
IX-T
X3(
-)11
GN
D12
IX-C
LK(+
)13
IX-C
LK(-
)14
GN
D15
IX-T
X2(
+)
16IX
-TX
2(-)
17G
ND
18IX
-TX
1(+
)19
IX-T
X1(
-)20
GN
D21
IX-T
X0(
+)
22IX
-TX
0(-)
23G
ND
GN
DG
ND
24 25 26V
CO
M27
NU
28G
ND
GN
DG
ND
29 30
LC
D M
OD
UL
E
AS
SE
MB
LY
CN
301
CN
3010
2319 2115 17 222018161410 126 8 13119751 3 4
2319 2115 17 222018161410 126 8 13119751 3 4
2G
ND
AL+
3.3V
GN
DP
-ON
+5V
P-O
N+
5VP
-ON
+9V
+4V
GN
D+
4V
+4V
GN
D
GN
D+
2.5V
+2.
5V
GN
D
GN
D+
15V
+35
VG
ND
PR
OT
EC
T2
PR
OT
EC
T1
+5V
/+12
V-L
CD
+5V
/+12
V-L
CD
2C
L552
A
CL5
52B
1
1G
ND
33
PR
OTE
CT2
(NU
)2
2P
RO
TEC
T3(N
U)
44
PR
OT
EC
T1
55
P-O
N-H
77
BACK
LIG
HT-P
WM
66
BAC
KLI
GH
T-O
N
88
GN
D
PR
OT
EC
T3(
NU
)
SC
LG
ND
SD
A
GN
DR
EM
OT
E
NU
AM
P-S
TB
YA
MP
-MU
TE
PW
R-C
ON
T
GN
D
GN
DA
UD
IO(L
)-O
UT
AU
DIO
(R)-
OU
T
LED
2
GN
DLE
D1
LED
3N
U
GN
DD
VD
-MA
IN-P
OW
ER
CN
302
P-O
N-H
GN
D
CN
3014 2319 2115 17 222018161410 126 8 13119751 3 42
2319 2115 17 222018161410 126 8 13119751 3 42
CLN
802
2C
N80
2
1S
P-P
(L)
SP
-N(L
)
CLN
801
2C
N80
1
1S
P-P
(R)
SP
-N(R
)
SP
802
SP
EA
KE
RL-
CH
SP
801
SP
EA
KE
RR
-CH
JAC
K C
BA
CO
MP
ON
EN
T-Y
-IN
2
CO
MP
ON
EN
T-P
b-IN
2
CO
MP
ON
EN
T-P
r-IN
2
CO
MP
ON
EN
T-Y
-IN
1
CO
MP
ON
EN
T-P
b-IN
1
CO
MP
ON
EN
T-P
r-IN
1
CO
MP
ON
EN
T-
AU
DIO
(L)-
IN1
CO
MP
ON
EN
T-
AU
DIO
(R)-
IN1
CO
MP
ON
EN
T-
AU
DIO
(L)-
IN2
CO
MP
ON
EN
T-
AU
DIO
(R)-
IN2
VID
EO
-IN
1
AU
DIO
(L)
-IN
1
AU
DIO
(R)
-IN
1
VID
EO
-IN
2
AU
DIO
(L)
-IN
2
AU
DIO
(R)
-IN
2
PC
-AU
DIO
-IN
S-V
IDE
O-I
N2
S-V
IDE
O-I
N1
CN
102
CN
3002
1 32 4 5
GN
DN
UK
EY-
IN1
NU
6N
U
KE
Y-IN
2
15 3 246
CN
601
CN
501
1 3
1 32
AC
LN
UH
OT-
GN
D2
CN
101B
CN
001
1 32 4 5
GN
DR
EM
OT
EA
L+3.
3V
LED
36
LED
2
NU
62 4 5
7LE
D1
8PW
R-C
ON
T8731
BA
CK
LIG
HT
CN
1050
21
BA
CK
LIG
HT
CN
1100
21
BA
CK
LIG
HT
CN
1150
21
BA
CK
LIG
HT
CN
1200
21
BA
CK
LIG
HT
CN
1250
21
BA
CK
LIG
HT
CN
1300
21
GND
DVD-SCLKDVD-CSDVD-PWR-REQDVD-SDATADVD-REMOTE
GND
GNDDVD-Y
DVD-Pb
DVD-AUDIO(L)
DVD-PrGND
GND
PROTECT4
DVD-AUDIO(R)GND
DVD-DISC-INDVD-DISC-OUT
DVD-SPDIFGND
CN
303
LED-CONTDVD-AUDIO-MUTE
CN
3017
23
19
21
15
17
22
20
18
16
14
10
12
6
8
13
11
9
7
5
1
34
2
23
19
21
15
17
22
20
18
16
14
10
12
6
8
13
11
9
7
5
1
34
2
LED
-CO
NT
2D
VD
-DIS
C-O
UT
3
EV
+1.
2V5
EV
+3.
3V6
EV
+3.
3V7
EV
+3.
3V8
DV
D-O
N+
3.3V
9D
VD
-ON
+5V
10E
V+
10V
11E
V+
10V
12G
ND
13G
ND
14G
ND
15G
ND
16G
ND
17G
ND
18G
ND
19P
WR
CO
N(N
U)
20D
VD
-SC
LK21
DV
D-C
S22
DV
D-D
ISC
-IN
23CN
202
EV
+1.
2V4
AL+
3.3V
1
DV
D-S
DAT
A24
DV
D-R
EM
OT
E25
DV
D-P
WR
-RE
Q26
TO
D
VD
MA
INC
BA
UN
ITC
N40
1
TO
WIR
ING
DIA
GR
AM
<
DV
DS
EC
TIO
N >
DV
D-P
b3
GN
D2
DV
D-P
r1
DV
D-Y
5CN
201
DV
D-A
UD
IO(R
)11
GN
D4
DV
D-A
UD
IO(L
)9
DV
D-A
UD
IO-M
UTE
10
GN
D12
GN
D6
GN
D7
GN
D8
DV
D-S
PD
IF13
TO
DV
D M
AIN
C
BA
UN
ITC
N60
1
CN
103
CN
104
1 2LE
D3
LED
221
LE
D C
BA
WIRING DIAGRAM < DVD SECTION >
A74F0WID12-2
CN
201
CN
301
LOA
D-D
ISC
LED-CONT2DVD-DISC-OUT3
EV+1.2V5EV+3.3V6EV+3.3V7EV+3.3V8DVD-ON+3.3V9DVD-ON+5V10EV+10V11EV+10V12GND13GND14GND15GND16GND17GND18GND19PWRCON(NU)20DVD-SCLK21DVD-CS22DVD-DISC-IN23
CN
401
EV+1.2V4
FS
TS
DE
TEC
TOR
79
112
36
5
M
SP
IND
LEM
OT
OR
M
SLE
DM
OT
OR
4
DV
D M
AIN
CB
A U
NIT
DR
IVE
CB
AD
VD
ME
CH
AN
ISM
PIC
K U
P U
NIT
LOAD-DISC 6SL(+) 5SL(-) 4GND 3SP(-) 2SP(+) 1
FS(-) 3TS(-) 4
GND(CD-PD) 5GND(DVD-PD) 6
PD-MONI 7DVD-LD 8
TS(+) 1FS(+) 2
GND 11NU 12
VREF 13NU 14
B 15C 16
GND(LD) 9CD-LD 10
A 17D 18
CD/DVD 19DVD-ON+5V 20
GND10GND9DVD-Y8
CN
601
DVD-AUDIO(R)14
GND11
DVD-Pb6GND5DVD-Pr4
GND7
DVD-AUDIO(L)12DVD-AUDIO-MUTE13
GND15DVD-SPDIF16
DIS
C-I
N
CN
5001
DIS
C-O
UT
LED-POWER 11DVD-DISC-OUT 22
GND 44DVD-DISC-IN 33
SE
NS
OR
CB
A
CN
801
CN
5001
is s
olde
red
dire
ctly
to th
e P
CB
.
AL+3.3V1
DVD-SDATA24DVD-REMOTE25DVD-PWR-REQ26
TO
WIR
ING
DIA
GR
AM
<
LC
D T
V S
EC
TIO
N >
TO
PO
WE
R S
UP
PLY
CB
A
CN
202
TO
PO
WE
R S
UP
PLY
CB
AC
N20
1
13-1 A7420TI
SYSTEM CONTROL TIMING CHARTS
Disc IN(TL221)
Sled Drive(TP303)
Disc Drive(TP301)
Focus Drive(TP304)
Tracking Drive(TP302)
0V
3.3V
0V
1.65V
0V
0V
0V
1.65V
1.65V
1.65V
Disc In
Disc Rotation
PlayDisc Stop
Disc Out
Disc In ~ Play/Play ~ Disc Out
14-1 A74F0LE
E C B E C B
24 13
121
1: Vin
2: Vo
3: GND1 2 3
G D S
1
2
4
3
1: A
2: K
3: E
4: C
B C E
G D S
42
15
26
27
141
56
43
14 8
1 7
44 23
221
B C E
G D S
KTA1267-GR-AT/PKTA1281Y-AT/PKTC3199-GR-AT/P
2SC2120-O(TE2 F T)2SD400(F)
Note:A: AnodeK: CathodeE: EmitterC: CollectorB: BaseR: ReferenceS: SourceG: GateD: Drain
LV1115M-TLE-EOZ9966SN-B1-0-TR/SSO
R2A11011FP
LTV817MBFLTV817MCF
NP22N055SLE-E1-AZ
BD5422EFS-E2
LD1117VBA10324AF-E2
2SA1887(F) KTC2026-Y/P
2SK3568(Q) 2SK3561(Q)
R A K
KIA431-AT/P
LEAD IDENTIFICATIONS
15-1 A74F0CEX
EXPLODED VIEWS
Cabinet
A1
B1
L19
B39
B12
B4
A4
A9
A14
A6
B8
A12
A21
A22
L4
L2
L2
L2
L2
L2
L13
L1
L7L1
B5
L9
L1
L18
L7
L9
L12 L12
L3L3
B7
A10
B18
L15
B1
L6
See Electrical Parts List for parts with this mark.
Digital MainCBA Unit
Inverter CBA
AC501
B19
L4
L4
L9
L1
L9
L1
B27
IR Sensor CBA
Function CBA
CLN801
CLN802
SP802
SP801
Power Supply CBA
A3
A20
L4
B19L9
B36
A19
A7
L4
L9
B6
L9
B20
B38
L9L11
L20
B21
L11
L13
A12
A12
Jack CBA
JunctionCBA
L9
T-CON CBA
L13L13
L1
L9
L1
L1
CLN101
CLN102
CL3007
CL7501
B11
L6
B10
B16
B16
B33
B35B37
L1
A11A13
B25
B35
L1L4
L4
LCD Module Assembly
B22
B34
L3
L12
B16
B16
B16
A18
L4
B24
L11
L11
L11
B32
B29
B32
L16
L16
B3
CL201 CL202
1B1
DVD Main CBA Unit
LED CBA
L16
L2
L13
L3-10
B32
L2
15-2 A74F0PEX
Packing
S1
S2
S5
S4
Tape
Packing Tape
Packing Tape
Packing Tape
Packing Tape
Packing Tape
Packing Tape
S3
S6
X1
X4 X9X3
Some Ref. Numbers are not in sequence.
X2
FRONT
20070508 16-1 A74F0CA
MECHANICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Ref. No. Description Part No.
A1 FRONT CABINET A74F0UH 1EM021726
A3 CONTROL PLATE A74F0UH 1EM322602A
A4 REAR CABINET A74F0UH 1EM021727
A6# RATING LABEL A74F0UH ----------
A7 FUNCTION KNOB A74F0UH 1EM221571
A9 STAND COVER A71F0UH 1EM021618
A10 REAR COVER A7260JH 1EM322484
A11 LED LENS A71F0UH 1EM322469
A12 STAND RUBBER FOOT L5001CB 1EM423855
A13 SENSOR LENS A71F0UH 1EM322470
A14 JACK PLATE A71F0UH 1EM221551
A18 DVD COVER A74F0UH 1EM021660
A19 EJECT KNOB A74F0UH 1EM322600
A20 ILLUMINATION LENS A74F0UH 1EM322599
A21 POP LABEL A71F0UH ----------
A22 PUNCHING SHEET A71F0UH 1EM021710
1B1 DVD MECHA SLOT E7 N7XT0KVM N7XT0KVM
B1 PANEL HOLDER 32V A71F0UH 1EM121831
B3 SHIELD BOX A74F0UH 1EM121927
B4 CHASSIS BRACKET 32V A71F0UH 1EM121806
B5 JACK HOLDER(A) A71F0UH 1EM221530
B6 JACK HOLDER(D) A71F0UH 1EM221535
B7 STAND BASE PLATE A71F0UH 1EM121808
B8 STAND HINGE A71F0UH 1EM221532
B16 CLOTH(10X180XT0.5) L0336JG 0EM408827
B18 CLOTH(10X30XT0.5) B5900UA 0EM404486
B19 CLOTH(20X65XT0.5) L0100JA 0EM407914
B20 GASKET A71F0UH 1EM424393
B21 FELT A74F0UH 1EM424374
B22 LASER CAUTION LABEL A74F0UH ----------
B24 DVD HOLDER A74F0UH 1EM121895
B25 SPEAKER BOX L A71F0UH 1EM121833
B27 INSULATION SHEET A71F0UH 1EM322580
B29 SHIELD PLATE A74F0UH 1EM221623
B32 GRAND TAPE (TR-19) A71F0UH 1EM424512
B33 RUBBER CUSHION (10X10X13) A71F0UH 1EM424527
B34 RUBBER CUSHION (10X10X20) A71F0UH 1EM424528
B35 SOUNDPROOF CUSHION A71F0UH 1EM424506
B36 CUSHION(80X10XT6) A71F0UH 1EM424511
B37 SPEAKER BOX R A71F0UH 1EM121907
B39 GASKET A74F0UH 1EM424537
CL201 WIRE ASSEMBLY 13PIN FFC 13PIN/297MM WX1A74F0-201
CL202 WIRE ASSEMBLY 26PIN FFC 26PIN/207MM WX1A74F0-102
CL3007 WIRE ASSEMBLY 101 30PIN / 70MM WX1A71F0-101
CL7501 WIRE ASSEMBLY 102 24PIN / 430MM WX1A71F0-102
CLN101 WIRE ASSEMBLY 003 8PIN / 330MM / AWG26 WX1A71F0-003
CLN102 WIRE ASSEMBLY 002 6PIN / 905MM / AWG26 WX1A71F0-002
CLN801 WIRE ASSEMBLY 006 2PIN / 450MM / AWG22 WX1A71F0-006
CLN802 WIRE ASSEMBLY 005 2PIN / 300MM / AWG22 WX1A74F0-005
FIL101 CLAMP FILTER ZCAT1518-0730 XL03022TE001
L1 SCREW P-TIGHT 4X14 BIND HEAD GBJP4140
L2 SCREW P-TIGHT M4X14 BIND HEAD+BLK GBHP4140
L3 SCREW P-TIGHT M3X12 DISH HEAD+ GDJP3120
L3-10 SCREW P-TIGHT M3X8 BIND HEAD+ GBJP3080
L4 SCREW P-TIGHT 3X10 BIND HEAD+ GBJP3100
L7 SCREW B-TIGHT 3X10 BIND HEAD+ BLK GBHB3100
L9 SCREW S-TIGHT M3X6 BIND HEAD+ GBJS3060
L11 DOUBLE SEMS SCREW M4X6 M4X6 FPJ34060
L12 DOUBLE SEMS SCREW M4X9 + BLACK L0130UA
0EM408146A
L13 DOUBLE SEMS SCREW M4X10 + BLK FPH34100
L15 NUT 3/8-32UNEF 0EM401451A
L16 ASSEMBLED SCREW ( D9 M3X6 ) A71F0UH 1EM424392
L18 SCREW S-TIGHT M3X8 BIND HEAD+ GBHS3080
L19 HEX SCREW #4-40 7MM 1EM422042
L20 SCREW S-TIGHT M3X10 BIND HEAD+ GBJS3100
SP801 SPEAKER MAGNETIC YDP613-1FN DSD0811EFU01
SP802 SPEAKER MAGNETIC YDP613-1FN DSD0811EFU01
PACKINGS1 CARTON A74F0UH 1EM424381
S2 STYROFOAM TOP A71F0UH 1EM021620
S3 STYROFOAM BOTTOM A71F0UH 1EM021621
S4 SET BAG L4300UA 1EM321546
S5 SERIAL NO. LABEL L9750UA ----------
S6 STAND SHEET L5001CB 1EM423856
ACCESSORIESX1 BAG POLYETHYLENE 235X365XT0.03 0EM408420A
X2# OWNERS MANUAL A74F0UH 1EMN22184A
X3 REMOTE CONTROL NF018UD 192/ECNLC5D1/NF018UD
NF018UD
X4 DRY BATTERY(SUNRISE) R6SSE/2S XB0M451MS002
X9 QUICK SETUP GUIDE A74F0UH 1EMN22188
Ref. No. Description Part No.
20070508 17-1 A74F0EL
ELECTRICAL PARTS LIST
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
LCD MODULE ASSEMBLY
*VCOM Adjustment and White Balance Adjustment are required when reparing T-CON CBA.
DIGITAL MAIN CBA UNIT
DVD MAIN CBA UNIT
MPS CBA
POWER SUPPLY CBA
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Part No.
LCD MODULE ASSEMBLYConsists of the following:
UF320XA
T-CON CBACELL ACF ASSEMBLYBACKLIGHT ASSEMBLY
1FSA10238--------------------
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT 1ESA14317
Ref. No. Description Part No.
DVD MAIN CBA UNIT N7ETAKUP
Ref. No. Description Part No.
MPS CBAConsists of the following:
1ESA14307
POWER SUPPLY CBA(MPS-1)FUNCTION CBA(MPS-2)IR SENSOR CBA(MPS-3)JACK CBA(MPS-4)LED CBA(MPS-5)
------------------------------
Ref. No. Description Part No.
POWER SUPPLY CBA(MPS-1)Consists of the following:
----------
CAPACITORSC601# ELECTROLYTIC CAPACIT0R 150µF/200V CA2D151S6012
C602 CERAMIC CAP. R K 680pF/2KV(HR) CCD3DKA0R681
C603 POLYESTER FILM CAP. (PB FREE) 0.0015µF/100V J
CA2A152DT018
C604 POLYESTER FILM CAP. (PB FREE) 0.027µF/100V J
CA2A273DT018
C605 CERAMIC CAP.(AX) B K 0.027µF/50V CA1J273TU011
C606 FILM CAP.(P) 0.1µF/50V J CMA1JJS00104
C608 SAFETY CAP. 4700pF/250V CCD2EMA0E472
C633 ELECTROLYTIC CAP. 1000µF/25V M CE1EMZNDL102
C634 ELECTROLYTIC CAP. 4700µF/10V M P=7.5 CE1AMZNDL472
C635 CERAMIC CAP.(AX) B K 0.01µF/50V CCA1JKT0B103
C636 CERAMIC CAP. R K 1500pF/2KV(HR) CCD3DKA0R152
C638 ELECTROLYTIC CAP. 4700µF/10V M P=7.5 CE1AMZNDL472
C639 ELECTROLYTIC CAP. 1000µF/50V M CE1JMZPDL102
C640 ELECTROLYTIC CAP. 22µF/50V M CE1JMASDL220
C642 CAP ELE STD-85 4700µF 6.3V SL CE0KMZNDL472
C643 ELECTROLYTIC CAP. 4700µF/10V M P=7.5 CE1AMZNDL472
C644 ELECTROLYTIC CAP. 1000µF/16V M CE1CMASDL102
C647 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C648 ELECTROLYTIC CAP. 1000µF/25V M CE1EMZNDL102
C650 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0
C652 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101
C653 ELECTROLYTIC CAP. 100µF/10V M CE1AMASDL101
C654 ELECTROLYTIC CAP. 4700µF/10V M P=7.5 CE1AMZNDL472
C655 ELECTROLYTIC CAP. 1000µF/10V M CE1AMASDL102
C656 CAP ELE STD-85 4700µF 6.3V SL CE0KMZNDL472
C657 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C658 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C659 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C660 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C661 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C662 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C663 ELECTROLYTIC CAP. 100µF/25V M CE1EMASDL101
C664 CAP ELE STD-85 4700µF 6.3V SL CE0KMZNDL472
C665 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C801 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101
C802 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
C803 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
C804 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101
C805 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C806 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C807 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C808 ELECTROLYTIC CAP. 3.3µF/50V M CE1JMASDL3R3
C809 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C810 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C811 ELECTROLYTIC CAP. 1000µF/25V M CE1EMZNDL102
C812 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C813 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C814 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C815 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C816 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C817 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C818 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C819 ELECTROLYTIC CAP. 1µF/50V M CE1JMASDL1R0
C821 ELECTROLYTIC CAP. 4.7µF/50V M CE1JMASDL4R7
C823 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C824 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
C825 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
C826 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C827 ELECTROLYTIC CAP. 4.7µF/50V M CE1JMASDL4R7
C833 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C834 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C835 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C842 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
C843 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
Ref. No. Description Part No.
20070508 17-2 A74F0EL
C851 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C857 ELECTROLYTIC CAP. 100µF/16V M CE1CMASDL101
C859 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470
C860 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
C861 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
C862 ELECTROLYTIC CAP. 4.7µF/50V M CE1JMASDL4R7
C863 ELECTROLYTIC CAP. 4.7µF/50V M CE1JMASDL4R7
C864 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C865 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C866 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C867 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C868 CHIP CERAMIC CAP.(1608) B K 2700pF/50V CHD1JK30B272
C869 CHIP CERAMIC CAP.(1608) B K 2700pF/50V CHD1JK30B272
C870 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C871 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C872 CHIP CERAMIC CAP. B K 0.068µF/50V CHD1JK30B683
C873 CHIP CERAMIC CAP.(1608) B K 5600pF/50V CHD1JK30B562
C875 ELECTROLYTIC CAP. 4.7µF/50V M CE1JMASDL4R7
C876 ELECTROLYTIC CAP. 4.7µF/50V M CE1JMASDL4R7
C877 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
C878 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
C880 CHIP CERAMIC CAP. (1608) B K 1µF/16V CHD1CK30B105
C1602 ELECTROLYTIC CAP. 1000µF/35V M CE1GMZADL102
C1603 CERAMIC CAP.(AX) B K 0.01µF/50V CCA1JKT0B103
C1604 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470
C1605 ELECTROLYTIC CAP. 47µF/25V M CE1EMASDL470
C1606 ELECTROLYTIC CAP. 1000µF/6.3V M CE0KMASDL102
C1607 ELECTROLYTIC CAP. 470µF/6.3V M CE0KMASDL471
C1608 ELECTROLYTIC CAP. 220µF/10V M CE1AMASDL221
CONNECTORSCN101B PH CONNECTOR TOP 8P B8B-PH-K-S
(LF)(SN)J3PHC08JG029
CN201 CONNECTOR FMN TOP 13P 13FMN-BTK-A(LF)(SN)
JCFNG13JG019
CN202 CONNECTOR PRINT MES 26FMN-BTK-A(LF)(SN)
JCFNG26JG019
CN301 TWG CONNECTOR 23P TWG-P23P-A1 J3TWA23TG001
CN302 TWG CONNECTOR 23P TWG-P23P-A1 J3TWA23TG001
CN303 TWG CONNECTOR 23P TWG-P23P-A1 J3TWA23TG001
CN601 WIRE ASSEMBLY 004 3PIN / 130MM / AWG18 WX1A71F0-004
CN801 CONNECTOR BASE 2P(EH) B 2B-EH-A(LF)(SN)
J3EHC02JG010
CN802 CONNECTOR BASE 2P(EH) B 2B-EH-A(LF)(SN)
J3EHC02JG010
DIODESD602# ZENER DIODE MTZJT-7739B QDTB00MTZJ39
D603 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D604# ZENER DIODE MTZJT-7727B QDTB00MTZJ27
D606 ZENER DIODE MTZJT-774.3B QDTB0MTZJ4R3
D607 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D611 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D612 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D613 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2
D631 ZENER DIODE MTZJT-775.6B QDTB0MTZJ5R6
D632 SCHOTTKY BARRIER DIODE ERB81-004 AERB81004***
D633 RECTIFIER DIODE FR202-B/P NDQZ000FR202
D635 ZENER DIODE MTZJT-7718B QDTB00MTZJ18
D636 RECTIFIER DIODE FR202-B/P NDQZ000FR202
D637 SCHOTTKY BARRIER DIODE SB240-B/P NDQZ000SB240
D640 SCHOTTKY BARRIER DIODE SB240-B/P NDQZ000SB240
D642 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D643 ZENER DIODE MTZJT-7712B QDTB00MTZJ12
D644 DIODE 1ZC43(Q) QDLZ001ZC43Q
D646 ZENER DIODE MTZJT-7718B QDTB00MTZJ18
Ref. No. Description Part No.
D647 SCHOTTKY BARRIER DIODE SB240-B/P NDQZ000SB240
D649 ZENER DIODE MTZJT-7733B QDTB00MTZJ33
D650 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2
D651 DIODE FR104-B NDLZ000FR104
D652 PCB JUMPER D0.6-P5.0 JW5.0T
D654 SCHOTTKY BARRIER DIODE SB140 NDWZ000SB140
D655 DIODE FR104-B NDLZ000FR104
D656 PCB JUMPER D0.6-P5.0 JW5.0T
D657 ZENER DIODE MTZJT-776.8B QDTB0MTZJ6R8
D658 ZENER DIODE MTZJT-775.1B QDTB0MTZJ5R1
D659 ZENER DIODE MTZJT-7716B QDTB00MTZJ16
D660 ZENER DIODE MTZJT-776.8B QDTB0MTZJ6R8
D664 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D665 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D666 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D667 SCHOTTKY BARRIER DIODE SB140 NDWZ000SB140
D668 PCB JUMPER D0.6-P5.0 JW5.0T
D670 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D671 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D672 ZENER DIODE MTZJT-7716B QDTB00MTZJ16
D674 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D675 ZENER DIODE MTZJT-7710B QDTB00MTZJ10
D676 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D677 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D801 ZENER DIODE MTZJT-7710B QDTB00MTZJ10
D802 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D803 PCB JUMPER D0.6-P5.0 JW5.0T
D810 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D811 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D851 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D852 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D853 ZENER DIODE EDZTE61 5.6B QD1B00EDZ5R6
D854 ZENER DIODE EDZTE61 5.6B QD1B00EDZ5R6
D1601 DIODE SCHOTTKY ERC84-009L QD4ZERC84009
D1602 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1603 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1604 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1605 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1606 RECTIFIER DIODE 1N4005 NDQZ001N4005
D1607 DIODE SCHOTTKY ERC84-009L QD4ZERC84009
D1610 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
ICSIC603# PHOTO COUPLER LTV817MCF NPECLTV817MF
IC637 IC LD1117V NSZBA0SSS046
IC801 IC POWER AMP BD5422EFS-E2 QSZBA0TRM113
IC802 IC SURROUND PROCESSOR LV1115M-TLM-E MFP24S
QSZBA0TSY050
IC1601 IC LD1117V NSZBA0SSS046
IC1602 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
IC1603 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
COILSL661 CHOKE COIL 22µH-K LLBD00PKV021
L801 COIL RADIAL LHLP10NB330M 33µH LLF3300TU003
L802 COIL RADIAL LHLP10NB330M 33µH LLF3300TU003
L803 COIL RADIAL LHLP10NB330M 33µH LLF3300TU003
L804 COIL RADIAL LHLP10NB330M 33µH LLF3300TU003
L805 INDUCTOR 22µH-K-5FT LLARKBSTU220
L852 INDUCTOR 100µH-K-5FT LLARKBSTU101
TRANSISTORSQ102 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q601# FET MOS 2SK3561(Q) IDSS100UA QFWZ2SK3561Q
Q602# TRANSISTOR 2SC2120-O(TE2 F T) QQS02SC2120F
Q630 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Ref. No. Description Part No.
20070508 17-3 A74F0EL
Q631 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q632# PNP TRANSISTOR POWER 2SA1887(F) QQWZ2SA1887F
Q633 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q635 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q636 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q637 PNP TRANSISTOR POWER 2SA1887(F) QQWZ2SA1887F
Q638# TRANSISTOR(PB FREE) KTC2026-Y/P NQEYKTC2026P
Q639 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F
Q640 PNP TRANSISTOR POWER 2SA1887(F) QQWZ2SA1887F
Q641 TRANSISTOR 2SC2120-Y(TE2 F T) QQSY2SC2120F
Q643 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q644 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q650 TRANSISTOR(PB FREE) KTC2026-Y/P NQEYKTC2026P
Q651 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q652 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q801 TRANSISTOR(PB FREE) KTC2026-Y/P NQEYKTC2026P
Q802 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q1601 TRANSISTOR KTA1281Y-AT/P NQVYKTA1281P
Q1602 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q1603 TRANSISTOR 2SD400(F) QQUF002SD400
Q1604 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
RESISTORSR109 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R129 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R139 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R140 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R601# METAL RES. 3W J 0.33 Ω RN03JZPZ0R33
R603 CARBON RES. 1/4W J 1.8k Ω RCX4JATZ0182
R604 CARBON RES. 1/4W J 390k Ω RCX4JATZ0394
R605 CARBON RES. 1/4W J 390k Ω RCX4JATZ0394
R606 CARBON RES. 1/4W J 390k Ω RCX4JATZ0394
R607 CARBON RES. 1/4W J 390k Ω RCX4JATZ0394
R608 PCB JUMPER D0.6-P5.0 JW5.0T
R609 CARBON RES. 1/4W J 2.2k Ω RCX4JATZ0222
R610 CARBON RES. 1/4W J 220 Ω RCX4JATZ0221
R611 CARBON RES. 1/4W J 820 Ω RCX4JATZ0821
R612 CARBON RES. 1/4W J 220 Ω RCX4JATZ0221
R613 CARBON RES. 1/4W J 180 Ω RCX4JATZ0181
R615 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R616 CARBON RES. 1/4W J 1.2k Ω RCX4JATZ0122
R617 CARBON RES. 1/4W J 1.2k Ω RCX4JATZ0122
R618 METAL OXIDE FILM RES. 2W J 10 Ω RN02100DP004
R619 METAL OXIDE FILM RES. 2W J 10 Ω RN02100DP004
R620 METAL OXIDE FILM RES. 2W J 1 Ω RN021R0DP004
R621 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R622 CARBON RES. 1/4W J 560 Ω RCX4JATZ0561
R633 CARBON RES. 1/4W J 820 Ω RCX4JATZ0821
R634 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R635 CARBON RES. 1/4W J 560 Ω RCX4JATZ0561
R636 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R639 CHIP RES. 1/10W J 560 Ω RRXAJR5Z0561
R641 CARBON RES. 1/4W J 1.2k Ω RCX4JATZ0122
R642 CARBON RES. 1/4W J 2.7k Ω RCX4JATZ0272
R644 PCB JUMPER D0.6-P5.0 JW5.0T
R645 CARBON RES. 1/4W J 12k Ω RCX4JATZ0123
R646 CARBON RES. 1/4W J 15k Ω RCX4JATZ0153
R649 METAL OXIDE FILM RES. 1W 470 Ω RN01471DP003
R650 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R651 CARBON RES. 1/4W J 100 Ω RCX4JATZ0101
R652 CARBON RES. 1/4W J 180 Ω RCX4JATZ0181
R653 CARBON RES. 1/4W J 180 Ω RCX4JATZ0181
R654 CARBON RES. 1/4W J 4.7k Ω RCX4JATZ0472
Ref. No. Description Part No.
R655 CHIP RES. 1/10W F 1.0k Ω RRXAFR5H1001
R656 CARBON RES. 1/4W J 4.7k Ω RCX4JATZ0472
R657 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R658 CHIP RES. 1/10W F 620 Ω RRXAFR5H6200
R659 CARBON RES. 1/4W J 180 Ω RCX4JATZ0181
R660 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R661 CARBON RES. 1/4W J 4.7k Ω RCX4JATZ0472
R662 CARBON RES. 1/4W J 4.7k Ω RCX4JATZ0472
R663 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R664 CHIP RES. 1/10W F 6.8k Ω RRXAFR5H6801
R665 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R666 CHIP RES. 1/10W F 6.8k Ω RRXAFR5H6801
R667 CHIP RES. 1/10W F 82.0 k Ω RRXAFR5H8202
R668 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R669 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R670 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R671 CARBON RES. 1/4W J 4.7k Ω RCX4JATZ0472
R672 CARBON RES. 1/4W J 1.8k Ω RCX4JATZ0182
R673 CARBON RES. 1/4W J 1.8k Ω RCX4JATZ0182
R675 METAL OXIDE FILM RES. 2W J 1 Ω RN021R0DP004
R676 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R677 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R678 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682
R679 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R680 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R681 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R682 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R683 CARBON RES. 1/4W J 22k Ω RCX4JATZ0223
R684 CHIP RES. 1/10W J 56k Ω RRXAJR5Z0563
R685 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R687 CARBON RES. 1/4W J 4.7k Ω RCX4JATZ0472
R688 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R689 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R690 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R691 CARBON RES. 1/4W J 1.2k Ω RCX4JATZ0122
R692 CARBON RES. 1/4W J 33k Ω RCX4JATZ0333
R693 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R694 CARBON RES. 1/4W J 560 Ω RCX4JATZ0561
R695 CARBON RES. 1/4W J 560 Ω RCX4JATZ0561
R696 CHIP RES. 1/10W J 56k Ω RRXAJR5Z0563
R800 PCB JUMPER D0.6-P12.5 JW12.5T
R801 CHIP RES. 1/10W F 100k Ω RRXAFR5H1003
R802 CHIP RES. 1/10W J 390k Ω RRXAJR5Z0394
R803 CARBON RES. 1/4W J 10 Ω RCX4JATZ0100
R804 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R805 CARBON RES. 1/4W J 6.8k Ω RCX4JATZ0682
R806 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R807 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R808 CHIP RES. 1/10W F 24k Ω RRXAFR5H2402
R809 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R810 CHIP RES. 1/10W F 24k Ω RRXAFR5H2402
R812 CHIP RES. 1/10W J 270k Ω RRXAJR5Z0274
R813 CHIP RES. 1/10W F 100k Ω RRXAFR5H1003
R814 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R815 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R816 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R817 CHIP RES. 1/10W J 4.7k Ω RRXAJR5Z0472
R819 CHIP RES. 1/10W J 2.7k Ω RRXAJR5Z0272
R820 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R854 CARBON RES. 1/4W J 100 Ω RCX4JATZ0101
R855 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R856 CARBON RES. 1/4W J 3.3k Ω RCX4JATZ0332
R859 CHIP RES. 1/10W J 10 Ω RRXAJR5Z0100
Ref. No. Description Part No.
20070508 17-4 A74F0EL
FUNCTION CBA
IR SENSOR CBA
R860 CHIP RES. 1/10W J 5.1k Ω RRXAJR5Z0512
R863 CHIP RES. 1/10W J 3.6k Ω RRXAJR5Z0362
R864 CHIP RES. 1/10W J 3.6k Ω RRXAJR5Z0362
R865 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R866 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R869 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R870 CHIP RES.(1608) 1/10W 0 Ω RRXAZR5Z0000
R1601 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R1602 CARBON RES. 1/4W J 390 Ω RCX4JATZ0391
R1603 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1604 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1605 METAL OXIDE FILM RES. 1W J 6.8 Ω RN016R8ZU001
R1606 CARBON RES. 1/4W J 2.2 Ω RCX4JATZ02R2
R1607 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R1608 RES CHIP.(1608) 1/10W J 0.30 Ω RRXAR30HH007
R1609 RES CHIP.(1608) 1/10W J 0.30 Ω RRXAR30HH007
R1610 CARBON RES. 1/4W J 18 Ω RCX4JATZ0180
R1611 CARBON RES. 1/4W J 18 Ω RCX4JATZ0180
R1612 CHIP RES. 1/10W J 470 Ω RRXAJR5Z0471
R1613 CHIP RES. 1/10W F 3.3k Ω RRXAFR5H3301
R1614 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1615 CARBON RES. 1/4W J 18 Ω RCX4JATZ0180
R1616 CARBON RES. 1/4W J 12 Ω RCX4JATZ0120
R1617 CARBON RES. 1/4W J 470 Ω RCX4JATZ0471
R1618 CHIP RES. 1/10W F 3.3k Ω RRXAFR5H3301
R1619 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1621 CHIP RES. 1/10W J 6.8k Ω RRXAJR5Z0682
R1622 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R1626 CARBON RES. 1/4W J 1.5k Ω RCX4JATZ0152
MISCELLANEOUSB10 HEAT SINK PKH ASSEMBLY L3201UB 1EM420648
B11 HEAT SINK PKP ASSEMBLY L4200EA 1EM420855
B38 HEAT SINK PMM A74F0UH 1EM424517
BC601 PCB JUMPER D0.6-P5.0 JW5.0T
BC602 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC631 PCB JUMPER D0.6-P5.0 JW5.0T
BC632 PCB JUMPER D0.6-P5.0 JW5.0T
BC633 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC634 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC635 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC1602 PCB JUMPER D0.6-P5.0 JW5.0T
FC601 CORE FERRITE TOROIDAL HF40T18X10X10 XL04018TE001
JS612 PCB JUMPER D0.6-P7.5 JW7.5T
JS632 PCB JUMPER D0.6-P15.0 JW15.0T
JS641 PCB JUMPER D0.6-P5.0 JW5.0T
JS642 PCB JUMPER D0.6-P5.0 JW5.0T
JS802 PCB JUMPER D0.6-P5.0 JW5.0T
JS803 PCB JUMPER D0.6-P5.0 JW5.0T
L6 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080
T601# TRANS POWER 7711 LTT3PC0KT025
Ref. No. Description Part No.
FUNCTION CBA(MPS-2)Consists of the following:
----------
CONNECTORCN102 CONNECTOR PRINT OSU S6B-PH-K-
S(LF)(SN)J3PHC06JG030
DIODESD104 ZENER DIODE MTZJT-775.6B QDTB0MTZJ5R6
D108 ZENER DIODE MTZJT-775.6B QDTB0MTZJ5R6
Ref. No. Description Part No.
RESISTORSR114 CHIP RES. 1/10W F 2.7k Ω RRXAFR5H2701
R115 CHIP RES. 1/10W F 2.2k Ω RRXAFR5H2201
R116 CHIP RES. 1/10W F 1.5k Ω RRXAFR5H1501
R117 CHIP RES. 1/10W F 1.5k Ω RRXAFR5H1501
R118 PCB JUMPER D0.6-P5.0 JW5.0T
R120 CHIP RES. 1/10W F 6.8k Ω RRXAFR5H6801
R121 CHIP RES. 1/10W F 4.7k Ω RRXAFR5H4701
R122 CHIP RES. 1/10W F 2.7k Ω RRXAFR5H2701
R123 CHIP RES. 1/10W F 2.2k Ω RRXAFR5H2201
R124 CHIP RES. 1/10W F 1.5k Ω RRXAFR5H1501
R125 CARBON RES. 1/4W J 220 Ω RCX4JATZ0221
R126 CHIP RES. 1/10W F 1.5k Ω RRXAFR5H1501
SWITCHESSW103 TACT SWITCH SKQSAB SST0101AL038
SW104 TACT SWITCH SKQSAB SST0101AL038
SW105 TACT SWITCH SKQSAB SST0101AL038
SW106 TACT SWITCH SKQSAB SST0101AL038
SW108 TACT SWITCH SKQSAB SST0101AL038
SW109 TACT SWITCH SKQSAB SST0101AL038
SW110 TACT SWITCH SKQSAB SST0101AL038
SW111 TACT SWITCH SKQSAB SST0101AL038
SW112 TACT SWITCH SKQSAB SST0101AL038
SW113 TACT SWITCH SKQSAB SST0101AL038
SW114 TACT SWITCH SKQSAB SST0101AL038
MISCELLANEOUSBC102 PCB JUMPER D0.6-P5.0 JW5.0T
JS101 PCB JUMPER D0.6-P5.0 JW5.0T
JS103 PCB JUMPER D0.6-P5.0 JW5.0T
Ref. No. Description Part No.
IR SENSOR CBA(MPS-3)Consists of the following:
----------
CAPACITORSC101 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMAVSL470
C102 CHIP CERAMIC CAP. F Z 0.01µF/50V CHD1JZ30F103
C105 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C106 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C107 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C112 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
CONNECTORSCN001 PH CONNECTOR SIDE 8P S8B-PH-K-
S(LF)(SN)J3PHC08JG030
CN103 PH CONNECTOR SIDE 2P S2B-PH-K-S(LF)(SN)
J3PHC02JG030
DIODESD101 LED L-53HT NP4Z000L53HT
D102 LED 333GT/E NPHZ00333GTE
RESISTORSR101 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R102 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R103 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R104 CHIP RES. 1/10W J 220 Ω RRXAJR5Z0221
R105 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R134 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000
R135 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000
SWITCHSW116 TACT SWITCH SKQSAB SST0101AL038
MISCELLANEOUSBC101 PCB JUMPER D0.6-P5.0 JW5.0T
RCV891 PHOTO LINK MODULE KSM-712TH2E USESJRSKK044
Ref. No. Description Part No.
20070508 17-5 A74F0EL
JACK CBARef. No. Description Part No.
JACK CBA(MPS-4)Consists of the following:
----------
CAPACITORSC7001 ELECTROLYTIC CAP. 47µF/16V M H7 CE1CMAVSL470
C7002 CHIP CERAMIC CAP.(2125) F Z 10µF/10V CHE1AZ30F106
C7003 CHIP CERAMIC CAP.(2125) F Z 10µF/10V CHE1AZ30F106
C7004 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7005 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7006 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7007 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7008 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C7009 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C7010 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C7012 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C7013 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V CHD1JZ30F104
C7101 ELECTROLYTIC CAP. 220µF/6.3V M H7 CE0KMAVSL221
C7102 CERAMIC CAP.(AX) B K 1000pF/50V CCA1JKT0B102
C7109 CHIP CERAMIC CAP. F Z 4.7µF/16V(2012) CHE1CZ30F475
C7110 CHIP CERAMIC CAP. F Z 4.7µF/16V(2012) CHE1CZ30F475
C7111 ELECTROLYTIC CAP. 220µF/6.3V M H7 CE0KMAVSL221
C7515 CHIP CERAMIC CAP. F Z 4.7µF/16V(2012) CHE1CZ30F475
C7516 CHIP CERAMIC CAP. F Z 4.7µF/16V(2012) CHE1CZ30F475
C7602 CHIP CERAMIC CAP. F Z 4.7µF/16V(2012) CHE1CZ30F475
C7605 CHIP CERAMIC CAP. F Z 4.7µF/16V(2012) CHE1CZ30F475
C7608 CHIP CERAMIC CAP. F Z 4.7µF/16V(2012) CHE1CZ30F475
C7611 CHIP CERAMIC CAP. F Z 4.7µF/16V(2012) CHE1CZ30F475
C7615 CHIP CERAMIC CAP. F Z 4.7µF/16V(2012) CHE1CZ30F475
C7618 CHIP CERAMIC CAP. F Z 4.7µF/16V(2012) CHE1CZ30F475
C7621 CHIP CERAMIC CAP. F Z 4.7µF/16V(2012) CHE1CZ30F475
C7624 CHIP CERAMIC CAP. F Z 4.7µF/16V(2012) CHE1CZ30F475
C7701 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7702 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7705 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7706 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7709 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7710 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7714 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7715 CHIP CERAMIC CAP.(1608) B K 0.047µF/50V CHD1JK30B473
C7718 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7719 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7723 CHIP CERAMIC CAP.(1608) CH J 100pF/50V CHD1JJ3CH101
C7724 CHIP CERAMIC CAP.(1608) B K 0.047µF/50V CHD1JK30B473
C7729 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390
C7730 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7733 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390
C7734 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7738 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390
C7739 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7743 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390
C7744 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7747 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390
C7748 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7751 CHIP CERAMIC CAP. CH J 39pF/50V CHD1JJ3CH390
C7752 CHIP CERAMIC CAP. F Z 0.47µF/16V CHD1CZ30F474
C7801 ELECTROLYTIC CAP. 100µF/16V M H7 CE1CMAVSL101
C7802 ELECTROLYTIC CAP. 100µF/16V M H7 CE1CMAVSL101
CONNECTORCN7501 FMN CONNECTOR TOP 24P 24FMN-BTK-
A(LF)(SN)JCFNG24JG019
DIODED7001 ZENER DIODE EDZTE61 5.6B QD1B00EDZ5R6
ICIC7001 IC VIDEO ANALOG INTERFACE R2A11011FP
QFP 56PINQSZBA0RHT066
COILSL7802 PCB JUMPER D0.6-P5.0 JW5.0T
L7803 PCB JUMPER D0.6-P5.0 JW5.0T
RESISTORSR7001 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R7002 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R7101 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7102 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7103 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7104 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7105 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000
R7106 CHIP RES.(1608) 1/10W 0 Ω RRXAJR5Z0000
R7111 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7112 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7502 PCB JUMPER D0.6-P5.0 JW5.0T
R7503 PCB JUMPER D0.6-P5.0 JW5.0T
R7504 PCB JUMPER D0.6-P5.0 JW5.0T
R7515 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183
R7516 CHIP RES. 1/10W J 18k Ω RRXAJR5Z0183
R7517 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7518 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R7601 CHIP RES. 1/10W J 43k Ω RRXAJR5Z0433
R7602 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273
R7604 CHIP RES. 1/10W J 43k Ω RRXAJR5Z0433
R7605 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273
R7607 CHIP RES. 1/10W J 43k Ω RRXAJR5Z0433
R7608 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273
R7610 CHIP RES. 1/10W J 43k Ω RRXAJR5Z0433
R7611 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273
R7613 CHIP RES. 1/10W J 43k Ω RRXAJR5Z0433
R7614 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273
R7616 CHIP RES. 1/10W J 43k Ω RRXAJR5Z0433
R7617 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273
R7619 CHIP RES. 1/10W J 43k Ω RRXAJR5Z0433
R7620 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273
R7622 CHIP RES. 1/10W J 43k Ω RRXAJR5Z0433
R7623 CHIP RES. 1/10W J 27k Ω RRXAJR5Z0273
R7701 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7702 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7708 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7709 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7715 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7716 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7723 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7724 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7730 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7731 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7738 CHIP RES. 1/10W J 75 Ω RRXAJR5Z0750
R7739 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7747 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0
R7748 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7755 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0
R7756 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7763 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0
R7764 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7771 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0
R7772 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7779 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0
R7780 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
R7787 CHIP RES.(1608) 1/10W F 75 Ω RRXAFR5H75R0
Ref. No. Description Part No.
20070508 17-6 A74F0EL
LED CBA
MUT CBA
INVERTER CBA
R7788 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
MISCELLANEOUSJK7501 JACK HPEP SML PCB S PJ-358H JXSJ020YUQ01
JK7701 JACK SW DIN PCB S YKF51-5379V JYEJ040JC002
JK7702 JACK SW RCA PCB S RCA-347HDT-02 JYRJ030YUQ01
JK7705 JACK SW DIN PCB L DIN-435C JYEL040YUQ02
JK7706 JACK SW RCA PCB L 05 RCA-340NI-01 JYRL030YUQ14
JK7711 JACK RCA PCB S 03 RCA-347HT-03 JXRJ030YUQ01
JK7712 JACK SW RCA PCB S RCA-228H(2)NI-01 JYRJ020YUQ02
JK7713 JACK RCA PCB S 03 RCA-347HT-03 JXRJ030YUQ01
JK7714 JACK SW RCA PCB S RCA-228H(2)NI-01 JYRJ020YUQ02
Ref. No. Description Part No.
LED CBA(MPS-5)Consists of the following:
----------
CAPACITORC111 CHIP CERAMIC CAP.(1608) F Z 0.1µF/50V ----------
CONNECTORCN104 WIRE ASSEMBLY 001 2PIN / 170MM / AWG22 WX1A74F0-001
DIODED106 LED BLUE SMD KPA-3010PBC NP1ZKPA3010P
RESISTORR137 CHIP RES. 1/10W J 10 Ω RRXAJB5Z0100
Ref. No. Description Part No.
MUT CBAConsists of the following:
1FSA10280
INVERTER CBAJUNCTION CBA
--------------------
Ref. No. Description Part No.
INVERTER CBAConsists of the following:
----------
CAPACITORSC501# ALUMINUM ELECTROLYTIC CAP 470µF/200V
MCA2D471NC190
C504# METALIZED FILM CAP. 0.47µF/250V CT2E474MS037
C505# METALIZED FILM CAP. 0.47µF/250V CT2E474MS037
C510 FILM CAP.(P) 0.022µF/50V J CA1J223MS029
C511 CERAMIC CAP.(AX) B J 390pF/50V CCA1JJT0B391
C512 CERAMIC CAP.(AX) B J 100pF/50V CCA1JJT0B101
C513 CERAMIC CAP.(AX) F Z 0.1µF/50V CCA1JZTFZ104
C514 ELECTROLYTIC CAP. 10µF/50V M CE1JMASDL100
C515 PCB JUMPER D0.6-P5.0 JW5.0T
C516 CAP METALIZED FILM 0.047µF 630V J CT2K473DT036
C517 CERAMIC CAP. R K 1000pF/2KV CCD3DKA0R102
C520 FILM CAP.(P) 0.022µF/50V J CA1J223MS029
C551 CHIP CERAMIC CAP. F Z 0.01µF/50V CHD1JZ30F103
C555 CERAMIC CAP. B K 1000pF/500V CCD2JKS0B102
C556 FILM CAP.(P) 0.01µF/50V J CA1J103MS029
C558# CAP ELE STD-85 4700µF/35V SL CE1GMZNDL472
C560 ELECTROLYTIC CAP. 0.1µF/50V M CE1JMASDL0R1
C561 CAP ELE STD-85 4700µF/35V SL CE1GMZNDL472
C1000 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1002 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1003 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1004 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1005 CHIP CERAMIC CAP.(1608) CH J 1000pF/50V CHD1JJ3CH102
Ref. No. Description Part No.
C1006 CHIP CERAMIC CAP.(1608) B K 0.047µF/50V CHD1JK30B473
C1007 CHIP CERAMIC CAP. CH J 330pF/50V CHD1JJ3CH331
C1008 CHIP CERAMIC CAP. F Z 2.2µF/10V CHD1AZ30F225
C1009 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1010 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1011 CHIP CERAMIC CAP.(1608) B K 0.47µF/10V CHD1AK30B474
C1012 CHIP CERAMIC CAP.(1608) B K 0.47µF/10V CHD1AK30B474
C1013 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1014 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1015 ELECTROLYTIC CAP. 470µF/35V M CE1GMZNDL471
C1016 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1017 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1018 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1019 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1020 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1021 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1032 ELECTROLYTIC CAP. 47µF/35V M CE1GMASDL470
C1040 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1044 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1046 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1061 CAP CERAMIC HV 15pF/3.15KV/SL/J CCD3FJASL150
C1062 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C1063 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1064 CAP CERAMIC HV 15pF/3.15KV/SL/J CCD3FJASL150
C1065 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C1066 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1067 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1100 ELECTROLYTIC CAP. 100µF/35V M CE1GMASDL101
C1101 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1102 ELECTROLYTIC CAP. 100µF/35V M CE1GMASDL101
C1103 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1104 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C1105 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C1106 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C1107 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C1111 CAP CERAMIC HV 15pF/3.15KV/SL/J CCD3FJASL150
C1112 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C1113 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1114 CAP CERAMIC HV 15pF/3.15KV/SL/J CCD3FJASL150
C1115 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C1116 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1117 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1161 CAP CERAMIC HV 15pF/3.15KV/SL/J CCD3FJASL150
C1162 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C1163 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1164 CAP CERAMIC HV 15pF/3.15KV/SL/J CCD3FJASL150
C1165 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C1166 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1167 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1211 CAP CERAMIC HV 15pF/3.15KV/SL/J CCD3FJASL150
C1212 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C1213 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1214 CAP CERAMIC HV 15pF/3.15KV/SL/J CCD3FJASL150
C1215 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C1216 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1217 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1250 ELECTROLYTIC CAP. 100µF/35V M CE1GMASDL101
C1251 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1252 ELECTROLYTIC CAP. 100µF/35V M CE1GMASDL101
C1253 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1254 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C1255 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C1256 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
Ref. No. Description Part No.
20070508 17-7 A74F0EL
C1257 CHIP CERAMIC CAP. CH J 220pF/50V CHD1JJ3CH221
C1261 CAP CERAMIC HV 15pF/3.15KV/SL/J CCD3FJASL150
C1262 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C1263 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1264 CAP CERAMIC HV 15pF/3.15KV/SL/J CCD3FJASL150
C1265 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C1266 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1267 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1311 CAP CERAMIC HV 15pF/3.15KV/SL/J CCD3FJASL150
C1312 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C1313 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1314 CAP CERAMIC HV 15pF/3.15KV/SL/J CCD3FJASL150
C1315 CHIP CERAMIC CAP. B K 1500pF/50V CHD1JK30B152
C1316 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1317 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C1500 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C1502 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C1550 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C1552 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
CONNECTORSCN501 CONNECTOR B2P3-VH(LF)(SN) J3VH020JG001
CN1050 CONNECTOR/JACK 1747386-1 JB17J02AP002
CN1100 CONNECTOR/JACK 1747386-1 JB17J02AP002
CN1150 CONNECTOR/JACK 1747386-1 JB17J02AP002
CN1200 CONNECTOR/JACK 1747386-1 JB17J02AP002
CN1250 CONNECTOR/JACK 1747386-1 JB17J02AP002
CN1300 CONNECTOR/JACK 1747386-1 JB17J02AP002
DIODESD502# DIODE 1N5406 NDLZ001N5406
D503# DIODE 1N5406 NDLZ001N5406
D504# DIODE 1N5406 NDLZ001N5406
D505# DIODE 1N5406 NDLZ001N5406
D507 DIODE 1ZC30(Q) QDLZ001ZC30Q
D509 DIODE FR154 NDLZ000FR154
D510 SCHOTTKY BARRIER DIODE ERA81-004Q QDLZRA81004Q
D511 FAST RECOVERY DIODE FE201-6 QDLZ00FE2016
D512 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D513 DIODE 1ZC30(Q) QDLZ001ZC30Q
D552# DIODE SCHOTTKY FD867-15L QDWZFD86715L
D553# DIODE SCHOTTKY FD867-15L QDWZFD86715L
D555# DIODE SCHOTTKY FD867-15L QDWZFD86715L
D556 PCB JUMPER D0.6-P5.0 JW5.0T
D557 IC SHUNT REGULATOR KIA431-AT/P NSZBA0TJY036
D558# DIODE SCHOTTKY FD867-15L QDWZFD86715L
D559 DIODE 1ZC30(Q) QDLZ001ZC30Q
D560 ZENER DIODE MTZJT-7727B QDTB00MTZJ27
D561 PCB JUMPER D0.6-P5.0 JW5.0T
D563 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1000 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1001 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1002 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2
D1003 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2
D1004 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2
D1005 ZENER DIODE MTZJT-776.2B QDTB0MTZJ6R2
D1006 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1021 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1042 ZENER DIODE MTZJT-7724B QDTB00MTZJ24
D1043 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1045 ZENER DIODE MTZJT-7724B QDTB00MTZJ24
D1046 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1060 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1061 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
Ref. No. Description Part No.
D1062 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1063 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1064 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1065 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1066 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1067 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1068 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1110 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1111 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1112 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1113 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1114 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1115 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1116 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1117 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1118 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1160 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1161 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1162 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1163 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1164 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1165 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1166 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1167 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1168 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1210 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1211 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1212 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1213 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1214 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1215 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1216 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1217 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1218 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1260 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1261 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1262 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1263 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1264 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1265 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1266 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1267 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1268 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1310 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1311 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1312 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1313 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1314 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1315 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1316 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1317 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1318 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1500 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1501 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1502 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1503 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1550 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1551 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1552 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1553 SWITCHING DIODE 1SS133(T-77) QDTZ001SS133
D1701 ZENER DIODE MTZJT-7718B QDTB00MTZJ18
D1702 ZENER DIODE MTZJT-773.3B QDTB0MTZJ3R3
Ref. No. Description Part No.
20070508 17-8 A74F0EL
ICSIC501 IC UCC28600DR SOIC 8PIN NSZAA0TTY017
IC509# PHOTO COUPLER LTV817MBF NPEBLTV817MF
IC510# PHOTO COUPLER LTV817MBF NPEBLTV817MF
IC1001 IC INVERTER CONTROLLER OZ9966SN-B1-0-TR/SSO
NSZBA0TTMC06
IC1500 IC BA10324AF-E2 QSZBA0TRM032
IC1550 IC BA10324AF-E2 QSZBA0TRM032
COILSL502# FILTER LLBG00ZY2015 LLBG00ZY2015
L503# FILTER LLBG00ZY2015 LLBG00ZY2015
TRANSISTORSQ501# MOS FET 2SK3568(Q) QQQZ02SK3568
Q502 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q551 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q552 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q1001 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q1002 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q1003 TRANSISTOR KTC3199-GR-AT/P NQS4KTC3199P
Q1020 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
Q1100 FET POWER MOS SMD NP22N055SLE-E1-AZ QF2ZNP22N055
Q1101 FET POWER MOS SMD NP22N055SLE-E1-AZ QF2ZNP22N055
Q1102 FET POWER MOS SMD NP22N055SLE-E1-AZ QF2ZNP22N055
Q1103 FET POWER MOS SMD NP22N055SLE-E1-AZ QF2ZNP22N055
Q1250 FET POWER MOS SMD NP22N055SLE-E1-AZ QF2ZNP22N055
Q1251 FET POWER MOS SMD NP22N055SLE-E1-AZ QF2ZNP22N055
Q1252 FET POWER MOS SMD NP22N055SLE-E1-AZ QF2ZNP22N055
Q1253 FET POWER MOS SMD NP22N055SLE-E1-AZ QF2ZNP22N055
Q1701 TRANSISTOR KTA1267-GR-AT/P NQS1KTA1267P
RESISTORSR501# CEMENT RESISTOR 5W J 0.47 Ω RW05R47PAK10
R503# CARBON RES. 1/2W J 3.3M Ω RCX2JZQZ0335
R505# METAL OXIDE FILM RES. 2W J 0.15 Ω RN02R15DP004
R506 CARBON RES. 1/4W J 10k Ω RCX4JATZ0103
R507 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R509 PCB JUMPER D0.6-P5.0 JW5.0T
R510# CARBON RES. 1/4W J 120k Ω RCX4JATZ0124
R511 CARBON RES. 1/4W J 120k Ω RCX4JATZ0124
R512 CARBON RES. 1/4W J 120k Ω RCX4JATZ0124
R513 CARBON RES. 1/4W J 22 Ω RCX4JATZ0220
R514 CARBON RES. 1/4W J 22 Ω RCX4JATZ0220
R515 CARBON RES. 1/4W J 220k Ω RCX4JATZ0224
R516 CARBON RES. 1/4W J 27k Ω RCX4JATZ0273
R517# CARBON RES. 1/4W J 560k Ω RCX4JATZ0564
R518 CARBON RES. 1/4W J 560k Ω RCX4JATZ0564
R519 CARBON RES. 1/4W J 560k Ω RCX4JATZ0564
R520 METAL OXIDE FILM RES. 3W J 10 Ω RN03100ZU001
R521 CARBON RES. 1/4W J 330k Ω RCX4JATZ0334
R522 METAL OXIDE RES. 3W J 18k Ω RN03183ZU001
R523 PCB JUMPER D0.6-P5.0 JW5.0T
R524 METAL OXIDE RES. 3W J 18k Ω RN03183ZU001
R551 CHIP RES. 1/10W J 5.6k Ω RRXAJR5Z0562
R553 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R554 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R555 CHIP RES. 1/10W J 820 Ω RRXAJR5Z0821
R556 PCB JUMPER D0.6-P5.0 JW5.0T
R557 CHIP RES. 1/10W F 2.2k Ω RRXAFR5H2201
R558 CHIP RES. 1/10W F 6.8k Ω RRXAFR5H6801
R559 CHIP RES. 1/10W F 6.8k Ω RRXAFR5H6801
R560 CHIP RES. 1/10W F 5.6k Ω RRXAFR5H5601
R562 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R564 CARBON RES. 1/4W J 2.7k Ω RCX4JATZ0272
R565 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
Ref. No. Description Part No.
R566 METAL OXIDE FILM RES. 2W J 1.5k Ω RN02152ZU001
R567 METAL OXIDE FILM RES. 2W J 1.5k Ω RN02152ZU001
R568 CHIP RES. 1/10W J 5.6k Ω RRXAJR5Z0562
R571 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R572 CHIP RES. 1/10W J 3.3k Ω RRXAJR5Z0332
R1000 CHIP RES. 1/10W J 20k Ω RRXAJR5Z0203
R1001 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1002 CARBON RES. 1/4W J 5.1k Ω RCX4JATZ0512
R1003 CHIP RES. 1/10W J 220k Ω RRXAJR5Z0224
R1004 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1005 CHIP RES. 1/10W F 160 k Ω RRXAFR5H1603
R1006 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1007 CHIP RES. 1/10W J 1M Ω RRXAJR5Z0105
R1008 CHIP RES. 1/10W J 51k Ω RRXAJR5Z0513
R1009 CHIP RES. 1/10W F 1M Ω RRXAFR5H1004
R1010 CHIP RES. 1/10W F 120 k Ω RRXAFR5H1203
R1011 CHIP RES. 1/10W F 120 k Ω RRXAFR5H1203
R1012 CHIP RES. 1/10W J 68k Ω RRXAJR5Z0683
R1013 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1014 CARBON RES. 1/4W J 51k Ω RCX4JATZ0513
R1015 CHIP RES.(1608) 1/10W F 5.1k Ω RRXAFR5H0512
R1020 CHIP RES. 1/10W J 1M Ω RRXAJR5Z0105
R1040 CARBON RES. 1/4W J 4.7k Ω RCX4JATZ0472
R1041 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1042 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R1043 CHIP RES. 1/10W J 22k Ω RRXAJR5Z0223
R1045 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R1046 CARBON RES. 1/4W J 6.8k Ω RCX4JATZ0682
R1047 CHIP RES. 1/10W J 1M Ω RRXAJR5Z0105
R1048 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R1050 CHIP RES. 1/10W J 47k Ω RRXAJR5Z0473
R1051 CARBON RES. 1/4W J 6.8k Ω RCX4JATZ0682
R1052 CHIP RES. 1/10W J 1M Ω RRXAJR5Z0105
R1053 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R1060 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R1061 CHIP RES. 1/10W J 20k Ω RRXAJR5Z0203
R1062 CHIP RES. 1/10W F 750 Ω RRXAFR5H7500
R1063 CARBON RES. 1/4W J 5.1k Ω RCX4JATZ0512
R1064 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1065 CHIP RES. 1/10W J 20k Ω RRXAJR5Z0203
R1066 CHIP RES. 1/10W F 750 Ω RRXAFR5H7500
R1067 CHIP RES. 1/10W J 5.1k Ω RRXAJR5Z0512
R1068 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1069 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1070 CHIP RES. 1/10W J 1M Ω RRXAJR5Z0105
R1071 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R1100 CHIP RES. 1/10W J 33 Ω RRXAJR5Z0330
R1101 CHIP RES. 1/10W J 33 Ω RRXAJR5Z0330
R1102 CHIP RES. 1/10W J 33 Ω RRXAJR5Z0330
R1103 CHIP RES. 1/10W J 33 Ω RRXAJR5Z0330
R1104 PCB JUMPER D0.6-P5.0 JW5.0T
R1105 PCB JUMPER D0.6-P5.0 JW5.0T
R1110 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R1111 CHIP RES. 1/10W J 20k Ω RRXAJR5Z0203
R1112 CHIP RES. 1/10W F 750 Ω RRXAFR5H7500
R1113 CHIP RES. 1/10W J 5.1k Ω RRXAJR5Z0512
R1114 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R1115 CHIP RES. 1/10W J 20k Ω RRXAJR5Z0203
R1116 CHIP RES. 1/10W F 750 Ω RRXAFR5H7500
R1117 CARBON RES. 1/4W J 5.1k Ω RCX4JATZ0512
R1118 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1119 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1120 CHIP RES. 1/10W J 1M Ω RRXAJR5Z0105
Ref. No. Description Part No.
20070508 17-9 A74F0EL
JUNCTION CBA
R1121 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R1160 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R1161 CHIP RES. 1/10W J 20k Ω RRXAJR5Z0203
R1162 CHIP RES. 1/10W F 750 Ω RRXAFR5H7500
R1163 CARBON RES. 1/4W J 5.1k Ω RCX4JATZ0512
R1164 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1165 CHIP RES. 1/10W J 20k Ω RRXAJR5Z0203
R1166 CHIP RES. 1/10W F 750 Ω RRXAFR5H7500
R1167 CARBON RES. 1/4W J 5.1k Ω RCX4JATZ0512
R1168 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1169 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1170 CHIP RES. 1/10W J 1M Ω RRXAJR5Z0105
R1171 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R1210 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1211 CHIP RES. 1/10W J 20k Ω RRXAJR5Z0203
R1212 CHIP RES. 1/10W F 750 Ω RRXAFR5H7500
R1213 CARBON RES. 1/4W J 5.1k Ω RCX4JATZ0512
R1214 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1215 CHIP RES. 1/10W J 20k Ω RRXAJR5Z0203
R1216 CHIP RES. 1/10W F 750 Ω RRXAFR5H7500
R1217 CHIP RES. 1/10W J 5.1k Ω RRXAJR5Z0512
R1218 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1219 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1220 CHIP RES. 1/10W J 1M Ω RRXAJR5Z0105
R1221 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R1250 CHIP RES. 1/10W J 33 Ω RRXAJR5Z0330
R1251 CHIP RES. 1/10W J 33 Ω RRXAJR5Z0330
R1252 CHIP RES. 1/10W J 33 Ω RRXAJR5Z0330
R1253 CHIP RES. 1/10W J 33 Ω RRXAJR5Z0330
R1254 PCB JUMPER D0.6-P5.0 JW5.0T
R1255 PCB JUMPER D0.6-P5.0 JW5.0T
R1260 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R1261 CHIP RES. 1/10W J 20k Ω RRXAJR5Z0203
R1262 CHIP RES. 1/10W F 750 Ω RRXAFR5H7500
R1263 CARBON RES. 1/4W J 5.1k Ω RCX4JATZ0512
R1264 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R1265 CHIP RES. 1/10W J 20k Ω RRXAJR5Z0203
R1266 CHIP RES. 1/10W F 750 Ω RRXAFR5H7500
R1267 CARBON RES. 1/4W J 5.1k Ω RCX4JATZ0512
R1268 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1269 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1270 CHIP RES. 1/10W J 1M Ω RRXAJR5Z0105
R1271 CARBON RES. 1/4W J 1k Ω RCX4JATZ0102
R1310 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R1311 CHIP RES. 1/10W J 20k Ω RRXAJR5Z0203
R1312 CHIP RES. 1/10W F 750 Ω RRXAFR5H7500
R1313 CHIP RES. 1/10W J 5.1k Ω RRXAJR5Z0512
R1314 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1315 CHIP RES. 1/10W J 20k Ω RRXAJR5Z0203
R1316 CHIP RES. 1/10W F 750 Ω RRXAFR5H7500
R1317 CHIP RES. 1/10W J 5.1k Ω RRXAJR5Z0512
R1318 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1319 CHIP RES. 1/10W F 10k Ω RRXAFR5H1002
R1320 CHIP RES. 1/10W J 1M Ω RRXAJR5Z0105
R1321 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R1500 CHIP RES. 1/10W F 47.0 k Ω RRXAFR5H4702
R1501 CHIP RES. 1/10W F 1.0k Ω RRXAFR5H1001
R1504 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1505 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1506 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1507 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1508 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R1509 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
Ref. No. Description Part No.
R1510 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1511 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1550 CHIP RES. 1/10W F 47.0 k Ω RRXAFR5H4702
R1551 CHIP RES. 1/10W F 1.0k Ω RRXAFR5H1001
R1554 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1555 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1556 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1557 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1558 CARBON RES. 1/4W J 100k Ω RCX4JATZ0104
R1559 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1560 CHIP RES. 1/10W J 100k Ω RRXAJR5Z0104
R1561 CHIP RES. 1/10W J 10k Ω RRXAJR5Z0103
R1701 CHIP RES. 1/10W J 1k Ω RRXAJR5Z0102
R1702 CHIP RES. 1/10W J 2.2k Ω RRXAJR5Z0222
R1703 CHIP RES. 1/10W J 100 Ω RRXAJR5Z0101
MISCELLANEOUSAC501# AC CORD W/O A GND WIRE UL 1935MM
BLACKWAC0192LW003
B12 HEAT SINK PMI ASSEMBLY A71F0UH 1EM424257
BC501 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC502 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC552 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC553 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC1000 PCB JUMPER D0.6-P5.0 JW5.0T
BC1001 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC1050 PCB JUMPER D0.6-P12.5 JW12.5T
BC1051 PCB JUMPER D0.6-P12.5 JW12.5T
BC1100 PCB JUMPER D0.6-P10.0 JW10.0T
BC1101 PCB JUMPER D0.6-P10.0 JW10.0T
BC1150 PCB JUMPER D0.6-P12.5 JW12.5T
BC1151 PCB JUMPER D0.6-P12.5 JW12.5T
BC1200 PCB JUMPER D0.6-P10.0 JW10.0T
BC1201 PCB JUMPER D0.6-P10.0 JW10.0T
BC1250 PCB JUMPER D0.6-P10.0 JW10.0T
BC1251 PCB JUMPER D0.6-P10.0 JW10.0T
BC1300 PCB JUMPER D0.6-P10.0 JW10.0T
BC1301 PCB JUMPER D0.6-P10.0 JW10.0T
CLN552 WIRE ASSEMBLY 001 8PIN / 190MM / AWG26 WX1A71F0-001
F501# FUSE STC4A125V U/CT PAGE20CW3402
FC501 CORE FERRITE TOROIDAL HF40T18X10X10 XL04018TE001
FH501 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002
FH502 FUSE HOLDER MSF-015 LF (B110) XH01Z00LY002
GP501# GAP. FNR-G3.10D FAZ000LD6005
JS553 PCB JUMPER D0.6-P5.0 JW5.0T
L6 SCREW B-TIGHT D3X8 BIND HEAD+ GBJB3080
JW501 PCB JUMPER D0.6-P15.0 JW15.0T
SA502# SURGE ABSORBER 470V+-10PER NVQZ10D471KB
T501# TRANS POWER 7715 LTT3PC0KT024
T1050 TRANS INVERTER ETJV23ZF2LAC LTZ2PC0MS008
T1100 TRANS INVERTER ETJV23ZF2LAC LTZ2PC0MS008
T1150 TRANS INVERTER ETJV23ZF2LAC LTZ2PC0MS008
T1200 TRANS INVERTER ETJV23ZF2LAC LTZ2PC0MS008
T1250 TRANS INVERTER ETJV23ZF2LAC LTZ2PC0MS008
T1300 TRANS INVERTER ETJV23ZF2LAC LTZ2PC0MS008
Ref. No. Description Part No.
JUNCTION CBAConsists of the following:
----------
CONNECTORCN552 242 SERIES CONNECTOR TUC-P08X-B1 WHT
STJCTUB08TG002
Ref. No. Description Part No.
© 2007 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.
LD320SS8A74F0UH
2007-05-23