SYSTEM SENSOR WIRELESS SOUNDER PRODUCT SPECIFICATION€¦ · 38(1) (2) Intermittent 2850 4Hz (150mS on, 100mS off) Pelican Crossing 10 79,14 95,14 Note (1): Tones not affected by

SYSTEM SENSOR WIRELESS SOUNDER PRODUCT SPECIFICATION

07/12/2018 AP Type ID 214 D.Po. B

DATE DESCRIPTION OF CHANGE CHG By ISSUE

THIS PRINT AND INFORMATION THEREIN ARE

PROPRIETARY TO LIFE SAFETY DISTRIBUTION GmbH AND SHALL NOT BE USED IN WHOLE OR IN PART WITHOUT THEIR EXPRESSED CONSENT.

TITLE 200S Commercial RF Sounder System Sensor product specifications

LIFE SAFETY DISTRIBUTION GmbH JAVASTRASSE 2

CH-8604 HEGNAU (SWITZERLAND)

Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

1 of 25

DRAWING NUMBER

S00-0664-000

Model name: WSO-xx-RF Introduction:

The 200 Series Commercial RF System is designed for use with compatible intelligent fire systems using the System Sensor 200/500 Series CLIP and Advanced communication protocols. It translates device coding from the radio domain to communication loop addresses recognised by the Control and Indicating Equipment (CIE). Each radio component contains a microcontroller and a transceiver with bi-directional RF data communications. There are two integrated antennae on the PCB for spatial diversity and for a uniform irradiation field. The radio devices are organized in a mesh network topology: this with the other above mentioned characteristics assures a connection in which the data security approaches that of hard-wired apparatus.


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

2 of 25

DRAWING NUMBER

S00-0664-000

Description:

the WSO-xx-RF is a battery operated sounder which groups one output sounder and a wireless radio frequency transceiver in a common housing. Through command codes, the CIE can toggle on and off the sounder, change the stage of the sounder tone and read the operating status of the device. In advanced protocol, the volume and the tone can also be controlled through the protocol. The Radio Gateway module translates the loop messages in radio messages and vice versa. The WSO-xx-RF appears to the CIE as an output module (CLIP protocol). The behaviour of a 200 Series Advanced sounder is simulated by the gateway. Output functions are specified as per the following table:

Fig.1 - 200/500 series protocol

For each tone selected two stages of sound are available. Through dedicated software user interface any available tone from the tone-table can be selected.

When used with the 500 Series protocol, the output command (CB10 and CB12) is used to activate the sounder, whilst the 2nd stage tone is selected by activating the LED output (CB10 and CB12) after first activating the main tone. The method is shown in the state diagram on Figure 1.


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

3 of 25

DRAWING NUMBER

S00-0664-000

Sounder Tone configuration (Approved according to en 54-3 only at high volume)

No Pattern Nominal

Frequency Switching Frequency Description Market Standard

2nd Stage Tone

Min dbA (4) Max dbA (5)

1 Not available

2 Alternating 800/970 1Hz UK BS5839 Pt1 8 84,04 98,54

3 Alternating 800/970 2Hz Alternating tone telecoms UK BS5839 Pt1,

FP1063.1 8 84,04 98,64

4 Alternating 2400/2900 3Hz Alternating High

Frequency 10 83,34 96,94

5 Alternating 2500/3100 2Hz Security Alarm 10 75,94 97,64

6 Alternating 988/645 2Hz 8 83,04 98,24

7 Continuous 660 All clear Sweden 1 82,14 99,44

8 (3) Continuous 970 BS 5839 Pt 1 2 76,44 98,74

9 Continuous 1200 2 83,34 101,94

10 Continuous 2850 HF Continuous 4 81,54 96,24

11 Sweep 150-1000 Rising from 150Hz to 1KHz in 10s, 40s@1KHz, falling from 1KHz

to150Hz in 10s, [email protected] 80s “Gasalarm” Tone 22 79,64 98,34

12 Not available

13(1) Sweep 500-1200 0.25 sec off, 3.75 sec on AS2220 evacuate tone NZ, Aus AS2220 12 86,44 101,84

14(1) Intermittent 660 3.33Hz 150ms on, 150ms off Swedish alarm tone Sweden 7 81,34 98,44

15(1) Intermittent 970 0.8Hz 0.25s on, 1s off Intermittent Tone UK BS 5839 Pt 1 8 75,24 98,04

16(1) Intermittent 970 0.5Hz 1s on, 1s off Back up alarm LF &

BS5839 Pt 1 UK BS5839 Pt 1 8 75,74 98,74

17(1) Intermittent 2850 1Hz Back up alarm HF &

BS5839 Pt 1 2nd tone UK BS5839 Pt 1 10 81,34 96,14

18(1) Intermittent 970 1Hz 500ms on, 500ms off LF BS5839 Pt 1 UK BS5839 Pt 1 8 75,74 98,54

19(1) Intermittent 950 0.22Hz (0.5s on, 0.5s off) rptx3, 1.5s off Australia IS8201 12 80,74 98,24

20 Continuous 800 BS 5839 Pt 1 22 84,14 98,64


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

4 of 25

DRAWING NUMBER

S00-0664-000

21(1) Sweep 400-1200 (0.5s on, 0.5s off)*3, 1.5s off Temporal 3 Evacuation

tone Australia

ISO8201 Temporal 3

12 84,14 100,24

22 Sweep 1200 - 500 0.99Hz 1s on, 0.01s off Evacuate, DIN tone &

PFEER Germany DIN, PFEER 20 84,94 100,84

23 Sweep 2400 - 2850

7Hz Fast sweep VdS Germany VdS 10 81,14 94,74

24(1) Sweep 500 - 1200 (0.5s off, 3.5s on) Slow whoop evacuate

Netherlands Netherlands NEN 2575 8 87,04 101,54

25 Sweep 800 - 970 50Hz LF Buzz BS5839 Pt 1 UK BS5839 Pt 1 8 82,14 97,84

26 Sweep 800 - 970 7Hz Fast sweep LF BS5839 Pt 1 UK BS5839 Pt 1 8 82,54 98,54

27 Sweep 800 - 970 1Hz Medium sweep LF, BS5839 Pt 1, VdS

UK, Germany

BS5839 Pt 1 VdS

8 83,64 98,94

28 Sweep 2400 – 2850

50Hz High frequency buzz 10 80,94 94,24

29 Sweep 500 – 1000

7Hz Fast whoop 8 84,24 99,34

30 Sweep 500 –

1200 – 500

0.166Hz rise 1s, stable 4s, fall 1s Siren style tone 8 85,44 101,14

31 Sweep 800 – 1000

2Hz 8 83,44 98,24

32 Sweep 2400 - 2850

1Hz 10 82,64 95,34

33(2) Continuous 4000 5 63,14 91,44

34 Not available

35 Not available

36(1) (2) Intermittent 660 0.05Hz 6.5s on, 13s off Sweden 7 82,44 99,34

37(1) (2) Intermittent 660 0.277Hz 1.8s on, 1.8s off Sweden 7 82,24 99,34

38(1) (2) Intermittent 2850 4Hz (150mS on, 100mS off) Pelican Crossing 10 79,14 95,14

Note (1): Tones not affected by intermittent user pattern Note (2): Only available through advanced protocol commands Note (3): Default tone Note (4): Minimum measured SPL on any direction at dist. 1m, V=2,5V, Volume High Note (5): Maximum measured SPL on any direction at dist. 1m, V=3,3V, Volume High


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

5 of 25

DRAWING NUMBER

S00-0664-000

The sounder module is wall mountable type and must be installed on a B501RF. A tamper detection system is implemented to detect the removal of the module from its base.

The radio circuit operates in the 865-870 MHz band using 18 different channels, with respect to E.T.S.I. EN 300-220-1 specifications and conforming to EN54-25.

Depending on the parameters stored and to the network condition, the module can be in one of the following states:

Uncommissioned: network parameters not downloaded; waiting to be programmed.

Synch: network parameters downloaded, trying to synchronize with the network and join it.

Idle: this status is entered when the gateway is disconnected from the loop for maintenance or for troubles. The RF device will stay in synch with the neighbors.

Normal: normal communication within the established network

Internal Fault: wireless/internal circuit initialization troubles

Power supply and LED:

4 x 3V, CR123A lithium batteries are used to power the device. The approved battery type for the module is Duracell Ultra 123 Lithium/Manganese dioxides and Panasonic Industrial 123. For battery life see the following graphs: other than the temperature, the power consumption depends on the number of parents and children assigned to the node. All these data refer to the specified batteries. Calculation and values must be considered valid in case a periodical sounder test is done with frequency of 30s/week, at most.


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

6 of 25

DRAWING NUMBER

S00-0664-000

Fig.3 - Battery life (4.9s super frame)

0

1

2

3

4

5

6

7

8

9

-30 -20 -10 0 10 20 30 40 50 60

Ye

ars

Temperature °C

2p, 0c

2p,2c

2p, 4c


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

7 of 25

DRAWING NUMBER

S00-0664-000

Electrical specifications:

ITEM TYP MIN MAX UNITS COMMENTS

Operating Voltage 3 2.5 3.3 VDC 4 x 3V Duracell Ultra 123 Lithium/Manganese Dioxide batteries or Panasonic Industrial 123

Supply current in TX 65 -- -- mA @ 25mW (14dBm) of Output Power

Supply Current in RX 18 -- -- mA @ 75.1 kbit/s

Supply Current in Stand by 10 -- -- µA During no communication phases

Max Current consumption Max Volume tone 20 120 -- -- mA Mean Current


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

8 of 25

DRAWING NUMBER

S00-0664-000

Transceiver characteristics:

The transceiver operates in the 865-870 MHz frequency band, using GFSK (Gaussian Frequency Shift Keying) modulation with respect to E.T.S.I. EN 300-220-1 specifications (Short Range Devices) and EN54-25: this allow having 18 channels available. The transmitter has an integrated PLL synthesizer which uses a crystal oscillator to guarantee the right carrier frequency. The integrated high efficiency power amplifier can transmit up to 14 dBm (25mW). System’s transfer rate is set to 75.1 kbps. The receiver sensitivity is -100 dB with respect to E.T.S.I. EN 300-220-1 specifications

Transceiver specifications:

ITEM TYP MIN MAX UNITS COMMENTS

Channel width -- -- 250 kHz

Modulation GFSK

Data rate 75.1 -- -- kbit/s

Output power (50) -- -- 14 dBm Vcc=3V

E.I.R.P. (Effective Isotropic Radiated Power) -- -- 13.5 dBm Vcc=3V

Antenna 2 Built on PCB

Linear range 500 -- -- m In free air


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

9 of 25

DRAWING NUMBER

S00-0664-000

CHANNELS AND FREQUENCIES USED

Channel Center frequency

(MHz)

Bandwidth

(kHz)

Band Max Power

(mW)

Max Duty Cycle

(%)

Note

0 865.125 250 h1.3 25 0.1 Reserved *

1 865.375 250 h1.3 25 0.1 *

2 865.625 250 h1.3 25 0.1 *

3 865.875 250 h1.3 25 0.1 *

4 866.125 250 h1.3 25 0.1 *

5 866.375 250 h1.3 25 0.1 *

6 866.625 250 h1.3 25 0.1 *

7 866.875 250 h1.3 25 0.1 *

8 867.125 250 h1.3 25 0.1 *

9 867.375 250 h1.3 25 0.1 *

10 867.625 250 h1.3 25 0.1 *

11 867.875 250 h1.3 25 0.1 *

12 868.150 250 h1.4 25 0.1

13 868.450 250 h1.4 25 0.1

14 868.825 250 h1.5 25 0.1

15 869.075 250 h1.5 25 0.1

16 869.525 250 h1.6 25 0.1

17 869.850 250 h1.7 25 0.1


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

10 of 25

DRAWING NUMBER

S00-0664-000

Following the situation of the implementation in countries according to ERC/REC 70-03 (22nd May 2018 edition)

Implementation status *: No info (default value) N: Not implemented U: Under study P: Planned L: Limited implementation Y: Implemented


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

11 of 25

DRAWING NUMBER

S00-0664-000


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

12 of 25

DRAWING NUMBER

S00-0664-000


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

13 of 25

DRAWING NUMBER

S00-0664-000

RF Protocol: The RF communication is established using “Cascading Wave Communication” protocol, developed by Honeywell. It provides a deterministic redundant communication without congesting the network in high traffic scenarios. The basic network element is called node, and the network root element (node 0) is called gateway. Every node allows for multiple links, in order to connect the node to the other ones in both network boundaries direction (children nodes) and network root nodes (parent nodes). Each parent receives data from its children, and forwards such data packets along with its own information back to the gateway. Each child receives data from its fathers and forwards such data packets to its descendants. This way, every node can be considered also as a repeater. Each child can have up to two parents, to guarantee redundancy and alternative paths to complete the data transmission to and from the gateway. In this way even if a node fails, there is always another one being able to complete the communication chain. Each node, but the gateway, can have up to 4 children. The gateway can have a number of children equal to the maximum number of nodes present on the network. To avoid messages collision a TDMA approach is used (Time Division Multiple Access) and this is why each device has a Temperature Controlled Chrystal Oscillator (TCXO) which ensures a high quality timing reference.

Gateway

(Node 0)

(Parent of Nodes

1,4,5)

Node 1

(Child of Node 0)

(Parent of Node 2)

Node 2

(Child of Node 1)

(Parent of Nodes

3,6,7)

Node 4

(Child of Node 0)

Node 5

(child of Node 0)

(Parent of Node 3)

Node 3

(Child of Node 2

and Node 5)

Node 6

(Child of Node 2)

Node 7

(Child of Node 2)

Fig.3 - Example of Network and parent child relationship


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

14 of 25

DRAWING NUMBER

S00-0664-000

MECHANICAL SPECIFICATIONS

SPECIFICATION TYP MIN MAX UNITS COMMENTS

Wire gauge for connector screw terminals 0,5 2,5 mm2

Height 75 mm On base installed

Diameter Ø 103 121 mm

Fixing centres 50 60 mm

Weight 285 g Batteries excluded

Weight 351 g Batteries included

ENVIRONMENTAL SPECIFICATION

SPECIFICATION TYP MIN MAX UNITS COMMENTS

International Protection (IP Grade) IP21C Not for external use

Humidity 5 95 % RH Non condensing

Temperature -30 60 °C Maximum installation temperature range

-30 60 °C Maximum operating temperature range


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

15 of 25

DRAWING NUMBER

S00-0664-000

Loop Communication Protocol:

The Radio Gateway module directly interfaces the CIE, translating the information received via RF from the module in a 200 Series Protocol (and its variants) frame. The RF sounder is seen from the CIE as a wired sounder of the 200 Series Advanced and has a type ID of an output (control) module, and takes one module address on the loop. For the different protocol variants, the waveform quantities and messages are specified below.

REFERENCE TABLE

Drawing no. Title

S61-432-000 500 Series Protocol Design Guide

Z99-0491-XXX Advanced Protocol Design Guide

SOUNDER PW DEFINITIONS

PW1 REFERENCE

PW2 REMOTE COMMAND STATUS

PW3 LATCHED SUPERVISION

PW4 ANALOG SUPERVISION

PW5 TYPE IDENTIFICATION

PW6* Not used

PW7* Not used

PW8* BATTERY LEVEL

PW9* LINK QUALITY

* If extended PW feature enabled.


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

16 of 25

DRAWING NUMBER

S00-0664-000

PW LIMITS ABSOLUTE LIMITS in µs (due to environmental/aging effects

MIN TYP MAX

PW1 285 305 315

PW2 (Normal) 285 305 315

PW2 (Remote Test) 570 610 630

PW3 (Normal) 285 305 315

PW3 (Open - Fault - Battery Not Fitted / Tamper Open / RF Link Trouble / Internal Fault / Battery Fault) 570 610 630

PW4 (Normal) 1024 1184 1328

PW4 (Maintenance Alert – Battery Warning, less than 6 months of battery life) 425 458 475

PW4 (Maintenance Urgent – Battery Fault, less than 1 month of battery life) 285 305 315

PW4 (Fault - Battery Not Fitted / Tamper Open / RF Link Trouble / Internal Fault) 128 152 160

PW4 (Open – Fault for amber LED blink) 690 --- 1008

PW5 570 610 630

PW6* 0 0 0

PW7* 0 0 0

PW8* (Estimated remaining battery life) In months: PW8/61µs 61 -- 2930

PW9* (Link Quality) Bad (RSSI < -94dBm; Comm loss > 40%) 285 305 315

PW9* (Link Quality) Poor (RSSI > -94dBm; Comm loss < 40%) 570 610 630

PW9* (Link Quality) Medium (RSSI > -84dBm; Comm loss < 20%) 855 915 945

PW9* (Link Quality) Good (RSSI > -74dBm; Comm loss < 5%) 1140 1190 1260

* If extended PW feature enabled.


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

17 of 25

DRAWING NUMBER

S00-0664-000

Bit Definition (500 series protocol)

Bit Interval Bit Definition Comments

Bit 1 Sensor / Module select Addressable sounder is the same as module – Set high

Bits 2 - 5 High address digit (0-F) Set by adjusting rotary dial on device

Bits 6 - 9 Low address digit (0-9) Set by adjusting rotary dial on device

Bits 10 - 12 Control Bits Refer to 500 Series protocol design guide S61-432-000

Bit 13 Even parity bits Generated by controller to provide even number of logic 1’s

Advanced protocol: While keeping backward compatibility, the Advanced protocol provides new capabilities, including bi-directional digital communication, interrupt feature,

group polling format for fast response to alarm conditions and improved power delivery. The Advanced protocol defines two modes of communication, designated Direct Poll and Group Poll: these two modes communicate either with one device at a time or simultaneously with a group of devices. This protocol contains a rapid alarm or fault detection feature which enables any device to signal the control panel when the device detects an alarm or fault condition. The alarm/fault condition represents a condition in the device which has been defined to require attention from the panel. This signal can be generated by any device where an alarm or fault condition occurs. This feature is factory set according to customer requirements, but it can be modified by special commands. Some parameters stored in FLASH memory can be read or written to by means of Advanced protocol commands: refer to Parameter Table for a description of the read and/or write parameters. Four bytes in the FLASH memory are used as a serial number, which can be read at panel start-up to detect double addresses.


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

18 of 25

DRAWING NUMBER

S00-0664-000

SUB-ADDRESS LOCATIONS

VALUE MEANING DIRECTION COMMENTS

0 System Input

116 Battery 1 level Input




120 Estimated remaining battery life Input

121 RSSI Parent 1 Input

122 RSSI Parent 2 Input

123 RSSI Child 1 Input




127 N.U. Input

129/139 LED control Output

140/146 Relay Output


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

19 of 25

DRAWING NUMBER

S00-0664-000

INPUT SUB-ADDRESS LIMITS

SUB

ADDRESS

MEANING CONDITION ABSOLUTE LIMITS

(due to environmental/aging effects)

COMMENTS

MIN TYP MAX

0 System Normal 50 50 50

Internal Fault 1 8

Battery Not Fitted 16 At least one battery not fitted

Battery Fault 17 Less than 1 month of remaining battery life

Tamper Open 18

RF Link Trouble 19

Battery Warning 38 Less than 6 months of remaining battery life

Power Up special value 255

116 Battery 1 level Normal 230 255




120 Estimated Remaining battery life Normal 6 255 Estimated remaining battery life in months

121 RSSI Parent 1 Bit 7, Bit 6 (LQ) 0 Comm Error Rate > 40%

1 Comm Error Rate < 40%



Bit 5 – Bit 0 (RSSI) RSSI = - (2*In121(RSSI))dBm

122 RSSI Parent 2 Bit 7, Bit 6 (LQ) 0 Comm Error Rate > 40%





123 RSSI Child 1 Bit 7, Bit 6 (LQ) 0 Comm Error Rate > 40%






07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

20 of 25

DRAWING NUMBER

S00-0664-000















Bit 5 – Bit 0 (RSSI) RSSI = - (2*In126(RSSI))Bm

127 N.U. -- 0 0 As a non isolated device


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

21 of 25

DRAWING NUMBER

S00-0664-000

PARAMETER TABLE (Latches/Interrupts applicable only to sub address 0, other sub addresses have no parameters)

SUB-ADDRESS 0

NR. 1 2 3 4 5 6 7 8 9

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25

PARAMETER Implementation ID (*) Type ID (*) OEM ID (*) Firmware Revision (*) User Checksum (*) Configuration Status (*) Device Configuration Latch Enable Register Latch Mode Register Rising Interrupt Enable Register Falling Interrupt Enable Register Alarm Hysteresis Value Trouble Hysteresis Value Threshold 0 Threshold 1 Threshold 2 Threshold 3 Group code 1 Group code 2 Group code 3 Group code 4 ON time multiplier (intermittent pattern) OFF time multiplier (intermittent pattern) User Byte 1 User Byte 2 * = read only ** same OEM ID of the associated gateway

DFLT 1

214 **

Rev. Nr. Chksum

1 1 3

12 12 12 0 0

30 41

255 255

0 0 0 0 0 0 0 0


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

22 of 25

DRAWING NUMBER

S00-0664-000

DIRECT AND GROUP POLLING COMMANDS

DIRECT/GROUP

COMMAND

FUNCTION SUBADDRESS

ID

DATA/DIRECTION DATA DESCRIPTION

0 Expansion For future command expansion

Command follows in next data packet

1 Set Output 129

130

131

133

2 bytes - panel to device (data byte repeated)

1 - 32

1

2

xxxxxxVV

xxAAxxRR

Sounder tone 1 – 32 1st stage 2nd stage VV 00 : Sounder volume set to default (High, Flash configured) 01 : Sounder volume set to low 10 : Sounder volume set to medium 11 : Sounder volume set to high x = not used AA 00 : Sounder OFF 11 : Sounder ON 10 : Sounder ON intermittent 01 : no action RR 00 : Step up regulator OFF 11 : Step up regulator ON 10, 01 : no action

2 Unused Unused command

3 Write Parameter 0 2 bytes - panel to device Parameter Number: 0

Data: 0 – 255

Write specified parameter (See Parameter Table for details)

4 Read Address by

Serial Number

NO 4 bytes - panel to device

1 byte - device to panel

$00.00.00.00 – $FF.FF.FF.FF

0 – 159

Transmit Address of factory programmed Serial Number

Decimal address returned

5 Disable Answer

by Serial Number

NO 4 bytes - panel to device $00.00.00.00 – $FF.FF.FF.FF Disable any answer of factory programmed Serial Number

6 Read Address Message ignored

7 Force Device

Update

NO No data – Force device update (factory use only)

8 Synchronize Message ignored

9 Reset Power On NO No data – Clears power-on condition in devices

10 Initialize Device NO No data – Re-read the whole non-volatile memory and initialize RAM variables

11 Unused Unused command


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

23 of 25

DRAWING NUMBER

S00-0664-000

Intermittent User

Pattern

Intermittent Sound Mode feature will be available on Advanced Protocol enabled devices only, either sounder or sounder-strobe. This feature will be applied to the non-intermittent sounder tone only, therefore some tones are not affected (see tone table) Both On and Off time periods can be set in a range between 0.5s and 127.5s through fixed interval steps of 500ms. The period are stored in parameter 22 and 23 (sub-address 0). This feature is automatically disabled if either On or Off time period are set to 0 (default) or either On or Off time period are changed through a “Write Parameter” Advanced Protocol command


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

24 of 25

DRAWING NUMBER

S00-0664-000

DIRECT

COMMAND

FUNCTION SUBADDRESS

ID

DATA/DIRECTION DATA LIMITS DESCRIPTION

129 Read Output Status 129

130

131

133

1 byte - device to panel 1-32

1

2

0

1

2 3

00AA00RR

Sounder tone Stage 1 Stage 2 Sounder volume set to default Sounder volume set to low Sounder volume set to medium Sounder volume set to high AA 00 : Sounder OFF 11 : Sounder ON 10 : Sounder ON intermittent 01 : no action RR 00 : Step up regulator OFF 11 : Step up regulator ON 10, 01 : no action

130 Read Condition

Latch

0 1 byte - device to panel 0 – 255 Read Condition Latch value

131 Read Parameter 0 1 byte - panel to device

1 byte - device to panel

Parameter Number: 0

Data: 0 – 255

Read specified device parameter

(See Parameter Table)

132 Read Multiple

Parameter

0 25 bytes - device to panel 0 – 255 Read all parameters from specified sub-address

(See Parameter Table)

133 Read Serial

Number by

Address

NO 4 bytes - device to panel $00.00.00.00 – $FF.FF.FF.FF Transmit factory programmed Serial Number for device addressed

134 Read Input value 116-126 1 byte - device to panel 0 – 255 Transmit processed value or sensing element raw values. If there is an

internal error e.g. memory checksum error, then sub-address 0 will be 1

135 Read Multiple

Input Values

NO 13 bytes - device to panel 0 – 255 Transmit all processed value and sensing element raw values

136 Read Multiple

Condition Latches

NO 1 bytes - device to panel 0 – 255 Transmit all sub-addresses Condition Latches


07/12/2018 AP Type ID 214 D.Po. B







Drawn by: A.Fr.

Date:27/07/2017

SHEET

A4 SIZE

SHT

25 of 25

DRAWING NUMBER

S00-0664-000

SPECIAL

COMMANDS

SUBADDRESS

ID

DATA/DIRECTION DATA LIMITS DESCRIPTION

Read Alarm Latch Units NO 10 bits - device to panel 0 – 1023 Devices with an alarm condition that match the specified tens address sink current in bits

9-0 corresponding to their units address

Read Alarm Latch Tens NO 10 bits - device to panel

10 bits - device to panel

(only 16 used)

0 – 1023

0 – 1008

Devices with an alarm condition sink current in bits 15-0 corresponding to their tens

address

Read Trouble Latch Units NO 10 bits - device to panel 0 – 1023 Devices with a trouble or power-on condition that match the specified tens address sink

current in bits 9-0 corresponding to their units address

Read Trouble Latch Tens NO 10 bits - device to panel

10 bits - device to panel

(only 16 used)

0 – 1023

0 – 1008

Devices with an interrupt sink current in bits 15-0 corresponding to their tens address

Read Presence NO 10 bits - device to panel 0 – 1023 All installed devices that match the specified the tens address sink current in bits 9-0

corresponding to their units address.

Null Message NO No data – Message only allows for Interrupt Interval to be used

Note: $ indicates hexadecimal value

Documents

SYSTEM SENSOR WIRELESS SOUNDER PRODUCT SPECIFICATION€¦ · 38(1) (2) Intermittent 2850 4Hz (150mS on, 100mS off) Pelican Crossing 10 79,14 95,14 Note (1): Tones not affected by