System Setup Guide - Panasonichelp.panasonic.ca/viewing/ALL/KX-HN6000/OI/HNB600_PNQX... · 2017-06-14 · System Setup Guide Home Network System HUB Model No. KX-HNB600 Thank you

System Setup GuideHome Network System

HUBModel No. KX-HNB600

Thank you for purchasing a Panasonic product.

This document explains how to configure the hub and access it using a mobiledevice. These steps must be followed before you can use the system.For details about how to use the system, refer to the User’s Guide (page 17).

Please read this document before using the unit and save it for future reference.For assistance, please contact us at 1-800-272-7033 or visit our Web site: http://shop.panasonic.com/support for customers in the U.S.A.

Please register your product: http://shop.panasonic.com/support

Printed in China

HNB600_(en_en)_0124_ver.201.pdf 1 2017/01/25 10:22:31

IntroductionAccessory information ..................................3

Important InformationAbout this system .........................................6For your safety .............................................6Important safety instructions ........................7Security cautions ..........................................7For best performance ...................................8Other information .........................................8

SetupPart names and functions ..........................10LED indicator ..............................................10Connections ...............................................11Wi-Fi® settings ...........................................12Registering another mobile device .............15Registering other devices to the hub ..........15

AppendixWireless communication range (DECT) .....17Accessing the User’s Guide .......................17Wall mounting ............................................18Specifications .............................................20Open source software notice .....................20Software information ..................................20FCC and other information .........................21Customer services .....................................23Limited Warranty (ONLY FOR U.S.A.) .......24

2

Table of Contents

HNB600_(en_en)_0124_ver.201.pdf 2 2017/01/25 10:22:34

Accessory information

Supplied accessories

No. Accessory item/Part number QuantityA AC adaptor/PNLV236-0Y 1B Telephone line cord/PQJA10075Z 1C Wall mounting adaptor/PNKL1049Z1 1

A B C

Additional accessoriesmicroSD card (not supplied)A commercially-available microSD card must be inserted into the hub in order to record imagesfrom cameras. The following types of microSD cards are supported.R microSD / SDHC card: Up to 32 GB

Other informationR Design and specifications are subject to change without notice.R The illustrations in these instructions may vary slightly from the actual product.

TrademarksR microSDHC Logo is a trademark of SD-3C, LLC.R iPhone and iPad are registered trademarks of Apple Inc.R iPad mini is a trademark of Apple Inc.R Android and Google Play are registered trademarks or trademarks of Google Inc.R Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of

Microsoft Corporation in the United States and/or other countries.R Wi-Fi®, WPA™, and WPA2™ are registered trademarks or trademarks of Wi-Fi Alliance®.R All other trademarks identified herein are the property of their respective owners.

NoticeR The hub supports microSD and microSDHC memory cards. In this document, the term

“microSD card” is used as a generic term for any of the supported cards.

For assistance, please visit http://shop.panasonic.com/support 3

Introduction

HNB600_(en_en)_0124_ver.201.pdf 3 2017/01/25 10:22:34

Expanding the Panasonic Home Network SystemThe Panasonic Home Network System is a wireless system that lets you create a powerfulnetwork of devices, such as cameras, sensors, and smart plugs, and control them all with aneasy-to-use app.Compatible devices are explained below. For information about the Home Network app, refer tothe User’s Guide (page 17).The maximum number of devices for each device type is listed below.

Digital Cordless Handset (KX-HNH100: 6 max.*1)R Makes and receives calls using your home landlineR Can be used to change the system’s arm modeR Displays system statusR Receives notification when the sensors are triggered

Indoor Camera (KX-HNC210: 4 max.*2)R Full-color camera and built-in microphone for live monitoring

and recordingR Built-in visual sensor, audio sensor, and temperature sensor

can be used to trigger other actions (camera recording, turningon a light, etc.)

R Built-in microphone and speaker for two-way communication

Outdoor Camera (KX-HNC600: 4 max.*2)R Full-color camera with built-in microphone for live monitoring

and recordingR Built-in visual sensor and infrared sensor can be used to trigger

other actions (camera recording, turning on a light, etc.)R Built-in microphone and speaker for two-way communicationR Splash proof design for permanent, outdoor installation

Window/Door Sensor (KX-HNS101: 50 max.*2)R Detects when the corresponding window or door is openedR Can be used to trigger other events (camera recording, turning

on a light, etc.)

Motion Sensor (KX-HNS102: 50 max.*2)R Detects motion in the surrounding areaR Can be used to trigger other events (camera recording, turning

on a light, etc.)

4 For assistance, please visit http://shop.panasonic.com/support

Introduction

HNB600_(en_en)_0124_ver.201.pdf 4 2017/01/25 10:22:34

Smart Plug (KX-HNA101: 50 max.*2)R Can be turned on and off using the handset or Home Network

app, when triggered by a sensor, or according to a scheduleR Built-in overcurrent and overwattage detection for added peace

of mindR Power consumption is logged for your reference

*1 Optional handsets may be a different color from that of the handset supplied as part of apre-configured bundle.

*2 A total of 6 cordless handsets, 4 cameras, and 50 other devices (motion sensors, window/door sensors, smart plugs, etc.) can be registered to the hub.

The Home Network System product lineup is growing!You can look forward to new devices that will make your Home Network System even moreuseful and convenient.For information about the latest devices and bundles, visit the website below.http://shop.panasonic.com/support

Mobile devices

Your mobile devices: 8 max.*1

You can expand the system by installing the Home Networkapp on your mobile devices (smartphones, tablets, etc.) andregistering your mobile devices to the hub.See page 12 for more information about the Home Networkapp.Note:R You must configure the hub’s Wi-Fi settings before you can

use the app.

*1 8 mobile devices can be registered to the hub, however, only the first 4 can use phonefeatures.


Introduction

HNB600_(en_en)_0124_ver.201.pdf 5 2017/01/25 10:22:34

About this systemR This system is an auxiliary system; it is not

designed to provide complete protectionfrom property loss. Panasonic will not beheld responsible in the event that propertyloss occurs while this system is in operation.

R The system’s wireless features are subjectto interference, therefore functionality in allsituations cannot be guaranteed.Panasonic will not be held responsible forinjury or damage to property that occurs inthe event of wireless communication erroror failure.

For your safetyTo prevent severe injury and loss of life/property, read this section carefully beforeusing the product to ensure proper and safeoperation of your product.

WARNING

Power connectionR Use only the power source marked on the

product.R Do not overload power outlets and

extension cords. This can result in the riskof fire or electric shock.

R Completely insert the AC adaptor/powerplug into the power outlet. Failure to do somay cause electric shock and/or excessiveheat resulting in a fire.

R Regularly remove any dust, etc. from theAC adaptor/power plug by pulling it fromthe power outlet, then wiping with a drycloth. Accumulated dust may cause aninsulation defect from moisture, etc.resulting in a fire.

R Unplug the product from power outlets if itemits smoke, an abnormal smell, or makesan unusual noise. These conditions cancause fire or electric shock. Confirm thatsmoke has stopped emitting and contact usat http://shop.panasonic.com/support

R Unplug from power outlets and never touchthe inside of the product if its casing has

been broken open. Danger of electric shockexists.

R Never touch the plug with wet hands.Danger of electric shock exists.

R Do not connect non-specified devices.

InstallationR To prevent the risk of fire or electrical

shock, do not expose the product to rain orany type of moisture.

R Do not place or use this product nearautomatically controlled devices such asautomatic doors and fire alarms. Radiowaves emitted from this product may causesuch devices to malfunction resulting in anaccident.

R Do not allow the AC adaptor or telephoneline cord to be excessively pulled, bent orplaced under heavy objects.

R Keep small parts, such as microSD cards,out of the reach of children. There is a riskof swallowing. In the event they areswallowed, seek medical adviceimmediately.

Operating safeguardsR Unplug the product from power outlets

before cleaning. Do not use liquid oraerosol cleaners.

R Do not disassemble the product.R Do not spill liquids (detergents, cleansers,

etc.) onto the telephone line cord plug, orallow it to become wet at all. This maycause a fire. If the telephone line cord plugbecomes wet, immediately pull it from thetelephone wall jack, and do not use.

R Never put metal objects inside the product.If metal objects enter the product, turn offthe circuit breaker and contact anauthorized service center.

MedicalR Consult the manufacturer of any personal

medical devices, such as pacemakers orhearing aids, to determine if they areadequately shielded from external RF(radio frequency) energy. DECT featuresoperate between 1.92 GHz and 1.93 GHzwith a peak transmission power of 115 mW.Wi-Fi features operate between 2.412 GHz


Important Information

HNB600_(en_en)_0124_ver.201.pdf 6 2017/01/25 10:22:35

and 2.462 GHz with a peak transmissionpower of 100 mW.

R Do not use the product in health carefacilities if any regulations posted in thearea instruct you not to do so. Hospitals orhealth care facilities may be usingequipment that could be sensitive toexternal RF energy.

CAUTION

Installation and locationR Never install wiring during a lightning storm.R Never install telephone line jacks in wet

locations unless the jack is specificallydesigned for wet locations.

R Never touch uninsulated telephone wires orterminals unless the telephone line hasbeen disconnected at the network interface.

R Use caution when installing or modifyingtelephone lines.

R The AC adaptor is used as the maindisconnect device. Ensure that the ACoutlet is installed near the product and iseasily accessible.

R This product is unable to make calls when:– there is a power failure.– when the cordless handset or mobile

device’s batteries need recharging orhave failed.

Important safetyinstructionsWhen using your product, basic safetyprecautions should always be followed toreduce the risk of fire, electric shock, andinjury to persons, including the following:1. Do not use this product near water for

example, near a bathtub, washbowl,kitchen sink, or laundry tub, in a wetbasement or near a swimming pool.

2. Avoid using a telephone (other than acordless type) during an electrical storm.There may be a remote risk of electricshock from lightning.

3. Do not use the telephone to report a gasleak in the vicinity of the leak.

4. Use only the power cord indicated in thisdocument.

SAVE THESE INSTRUCTIONS

Security cautionsTake appropriate measures to avoid thefollowing security breaches when using thisproduct.– Leaks of private information– Unauthorized use of this product– Unauthorized interference or suspension of

the use of this product

Take the following measures to avoid securitybreaches:R Configure the wireless router that connects

your mobile device to this product to useencryption for all wireless communication.

R You may be vulnerable to securitybreaches if the unit is used with the loginpassword, disarm code, or PIN code, orother settings at their defaults values.Configure your own values for thesesettings.

R Do not use passwords that could be easilyguessed by a third party. If you keep arecord of your passwords, protect thatrecord. Change passwords regularly.

R If you lose your mobile device, change thepassword used to access this product.

R If you enable the product’s auto loginfeature, enable the screen lock or similarsecurity feature on your mobile device.

R Take care when performing importantsecurity related operations such as deletingMAC address, unit IDs, etc.

R To prevent disclosure of personalinformation, enable the screen lock orsimilar security feature on your mobiledevice.

R When submitting the product for repair,make a note of any important informationstored in the product, as this informationmay be erased or changed as part of therepair process.

R Before handing the product over to a thirdparty for repair or other purposes, performa factory data reset to erase any data



HNB600_(en_en)_0124_ver.201.pdf 7 2017/01/25 10:22:35

stored in the product and remove themicroSD card. Use only trusted repairservices authorized by Panasonic.

R Before disposing of the product, perform afactory data reset to erase any data storedin the product. Remove and erase themicroSD card.

R If your mobile device will no longer be usedwith the product, delete your mobiledevice’s registration from the product anddelete the corresponding app from yourmobile device.

R If this product experiences a power outage,its date and time setting may becomeincorrect. In this case, the date and timesetting will be automatically corrected whenyour mobile device and this product areconnected to the same wireless network.

Additionally, note the following.R Multiple hubs cannot be used on the same

network.R Only one mobile device can access this

product while away from home. If a secondmobile device connects to this productwhile away from home, the first mobiledevice is disconnected.

R Communications may be interrupteddepending on network conditions andwireless signal quality.

R This product may be used in ways thatviolate the privacy or publicity rights ofothers. You are responsible for the ways inwhich this product is used.

For best performanceHub location/avoiding noiseThe hub and other compatible Panasonicdevices use radio waves to communicate witheach other.R For maximum coverage and noise-free

communications, place your hub:– at a convenient, high, and central

location with no obstructions betweenthe devices and hub in an indoorenvironment.

– away from electronic appliances such asTVs, radios, personal computers,wireless devices, or other phones.

– facing away from radio frequencytransmitters, such as external antennasof mobile phone cell stations. (Avoidputting the hub on a bay window or neara window.)

R Coverage and voice quality depends on thelocal environmental conditions.

R If the reception for a hub location is notsatisfactory, move the hub to anotherlocation for better reception.

EnvironmentR Keep the product away from electrical noise

generating devices, such as fluorescentlamps and motors.

R The product should be kept free fromexcessive smoke, dust, high temperature,and vibration.

R The product should not be exposed todirect sunlight.

R Do not place heavy objects on top of theproduct.

R When you leave the product unused for along period of time, unplug the product fromthe power outlet.

R The product should be kept away from heatsources such as heaters, kitchen stoves,etc. It should not be placed in rooms wherethe temperature is less than 0 °C (32 °F) orgreater than 40 °C (104 °F). Dampbasements should also be avoided.

R The maximum communication range maybe shortened when the product is used inthe following places: Near obstacles suchas hills, tunnels, underground, near metalobjects such as wire fences, etc.

R Operating the product near electricalappliances may cause interference. Moveaway from the electrical appliances.

Other informationRoutine careR Wipe the outer surface of the product with a

soft moist cloth.



HNB600_(en_en)_0124_ver.201.pdf 8 2017/01/25 10:22:35

R Do not use benzine, thinner, or anyabrasive powder.

Protecting your recordingsR Do not remove the microSD card or

disconnect the hub’s AC adaptor whilereading or writing data to the microSD card.Data on the card could become corrupted.

R If a microSD card malfunctions or isexposed to electromagnetic waves or staticelectricity, data on the card could becomecorrupted or erased. Therefore werecommend backing up important data to acomputer or other device.

Notice for product disposal, transfer,or returnR This product can store your private/

confidential information. To protect yourprivacy/confidentiality, we recommend thatyou erase information such as phonebookor caller list entries from the memory beforeyou dispose of, transfer, or return theproduct.

Notice



HNB600_(en_en)_0124_ver.201.pdf 9 2017/01/25 10:22:35

Part names and functions

C

BA

D E

G H I

F

SpeakerLED indicatorDC jackLINE jackMWi-Fi SETUPNUsed when performing initial setup.microSD card slotUsed when inserting a microSD card.Remove the label when inserting.M HANDSET/LOCATORNUsed when registering a handset. Youcan also press this button to locate amisplaced handset.M CAMERANUsed when registering a camera.M OTHER DEVICENUsed when registering other devices,such as sensors and smart plugs.

LED indicatorYou can use the LED indicator to confirm thehub’s status.

Indicator StatusOff No power, or LED

indicator is turnedoff*1

Green, lit Normal operation,connected towireless router*1

Green, blinkingslowly

Registration mode

Green, blinkingquickly

Hub is searching forwireless router

Alternating:Green, blinkingslowlyYellow, blinkingslowly

Hub is starting up(cannot be usedyet)*2

Red, lit Alarm system isarmed*1

Red, blinking quickly Alarm system wastriggered

Yellow, lit Initial setup requiredYellow, blinkingslowly

Initial setup inprogress, mobiledevice connected

Yellow, blinking Initial setup isstarting

*1 You can configure the hub so that its LEDindicator does not light during normaloperation. For more information, refer tothe User’s Guide (page 17).

*2 It may take some time for the hub to finishstarting up.


Setup

HNB600_(en_en)_0124_ver.201.pdf 10 2017/01/25 10:22:35

ConnectionsInsert the AC adaptor plug firmly into theDC jack.Secure the AC adaptor cord by wrappingit around the hook.Connect the AC adaptor to the poweroutlet.Insert the telephone line cord into theLINE jack and a single-line telephone jack(RJ11C) until you hear a click.*1DSL/ADSL service users only: Connectyour DSL/ADSL filter (not supplied).*1Outdoor Camera (KX-HNC600) orIndoor Camera (KX-HNC210) usersonly: Remove the label covering the cardslot and then insert the microSD card (notsupplied) into the slot with the notchedcorner (1) facing upwards (2) until itclicks into place.

*1 This step is only necessary if you want touse the landline phone features. Fordetails about the landline phone features,refer to the User’s Guide (page 17).

Note:R Use only the supplied Panasonic AC

adaptor PNLV236.R A microSD card (not supplied) is required to

record images from cameras. Refer to theinformation about the available microSDcard (page 3).

R To remove the microSD card, push in themicroSD card and then remove it.

4

5

4

3

2

1

6

12

Note about power connections

AC adaptor connectionR The AC adaptor must remain connected at

all times. (It is normal for the adaptor to feelwarm during use.)

R The AC adaptor should be connected to avertically oriented or floor-mounted ACoutlet. Do not connect the AC adaptor to aceiling-mounted AC outlet, as the weight ofthe adaptor may cause it to becomedisconnected.


Setup

HNB600_(en_en)_0124_ver.201.pdf 11 2017/01/25 10:22:35

Power failureR The hub will not work during a power failure.R The hub’s telephone features will not work

during a power failure. We recommendconnecting a corded-type telephone thatdoes not use an AC adaptor to yourtelephone line.

Wi-Fi® settingsAfter you have connected your hub, here iswhat you will need to do in order to access thesystem from your mobile device. Eachprocedure is explained in this chapter.1 Download

Download the [Home Network] app toyour mobile device.

2 Initial setupUse the [Home Network] app toconfigure the hub to connect to yourwireless router, and then register yourmobile device to the hub.

Downloading the [HomeNetwork] appDownload information is available at the webpage listed below.

www.panasonic.net/pcc/support/tel/homenetwork/

Compatible mobile devicesiPhone® 4 or later, iPad®, or iPad mini™ (iOS6.0 or later) or an Android™ device (Android4.0 or later)Note:R The [Home Network] app may not function

properly depending on the systemenvironment, such as the model of yourmobile device, peripherals connected toyour mobile device, and the apps installedon your mobile device.

R The following Android devices are notcompatible with the [Home Network] app.– Android devices that are not supported

by Google Play– Android devices with limited hardware

features (Bluetooth, Wi-Fi, andmicrophone support are required.)

Initial setupConfirm the following before you begin.– Make sure you have installed the [Home

Network] app on your mobile device– Make sure the hub and your wireless router

are turned on and the hub’s LED indicatoris lit in yellow

– Make sure the hub is located within rangeof your wireless router

– Make sure your mobile device is connectedto your wireless router

– Make sure your mobile device can connectto the Internet

– Make sure you know the network name(SSID) and password assigned to yourwireless router

Initial setup for iPhone, iPad1 Start the [Home Network] app.

R If prompted, follow the on-screeninstructions and select the appropriateregion/country.

R If prompted to select the device to beset up, tap [Hub].

2 When prompted, tap [Set up the Hub].3 When prompted, press MWi-Fi SETUPN

on the hub.R The LED indicator blinks in yellow.


Setup

HNB600_(en_en)_0124_ver.201.pdf 12 2017/01/25 10:22:35

4 Change your mobile device’s Wi-Fisetting temporarily so that it connects tothe hub directly.R Open your mobile device’s [Settings]

app, tap [Wi-Fi], select“KX-HNB600_Panasonic”, enter“00000000” as the password, and thentap [Join].

R If more than 1 item named“KX-HNB600_Panasonic” is displayed,wait approx. 10 minutes and performthis procedure from the beginning.

5 Start the [Home Network] app again.6 If necessary, enter the password required

to connect to your wireless router andthen tap [Next].R The hub and your mobile device

connect to your wireless router.R If prompted, follow the on-screen

instructions and connect your mobiledevice to your wireless router, start theapp again, and then tap [Add ThisMobile Device].

R If you enter the wrong Wi-Fi password,[Setup failed.] is displayed and thehub’s LED indicator lights.Proceed as follows according to thecolor of the hub’s LED indicator.– If the LED indicator is lit in yellow,

repeat the initial setup procedurefrom the beginning.

– If the LED indicator is blinkingquickly in green, you must reset thehub’s Wi-Fi settings. See “If thehub's LED indicator blinks in green”,page 13.

7 When prompted, press MWi-Fi SETUPNon the hub.R Your mobile device will be registered

to the hub.8 When prompted, follow the on-screen

instructions and set the password used tolog in to the hub while away from homeand then tap [OK].

9 When prompted, enter a name for thehub and your mobile device and then tap[OK].R The hub name setting is used by your

mobile device to identify the hub. Thisis useful when you have multiple hubs.

R The mobile device name setting isused by the hub and other systemusers to identify your mobile device.This is useful when performing certainoperations, such as deregistering ormaking intercom calls using a cordlesshandset.

10 When prompted, select whether you wantto customize device profiles, i.e., thedevice name, location, and other settingsfor your devices.R If you choose not to customize the

device profiles now, you can changethem later if desired. For details aboutcustomizing device profiles, refer to theUser’s Guide (page 17).

R If you choose to customize the deviceprofiles now, change each setting asdesired. When finished, tap repeatedly until the “completed”message is displayed.

R The app’s home screen is displayedwhen initial setup is complete.

If the hub's LED indicator blinks in greenIf you enter the wrong Wi-Fi password duringthe initial setup procedure for iPhone or iPad,[Setup failed.] is displayed and the hub’s LEDindicator blinks quickly in green. In this case,perform the following.1. Press and hold the 3 registration buttons

on the side of the hub and MWi-Fi SETUPNon the back of the hub at the same time (4buttons total) until the hub’s LED indicatorblinks slowly in green and yellow.

2. Wait for the hub’s LED indicator to light inyellow.

3. Repeat the initial setup procedure (“Initialsetup for iPhone, iPad”, page 12).


Setup

HNB600_(en_en)_0124_ver.201.pdf 13 2017/01/25 10:22:35

Initial setup for Android devices1 Start the [Home Network] app.

R If prompted, follow the on-screeninstructions and select the appropriateregion/country.


2 When prompted, tap [Set up the Hub].3 When prompted, press MWi-Fi SETUPN

on the hub.R The LED indicator blinks in yellow.R The app temporarily changes your

mobile device’s Wi-Fi setting so that itconnects to the hub directly.

4 If necessary, enter the password requiredto connect to your wireless router andthen tap [Next].R The hub and your mobile device

connect to your wireless router.5 When prompted, press MWi-Fi SETUPN

on the hub.R Your mobile device will be registered


instructions and set the password used tolog in to the hub while away from homeand then tap [OK].

7 When prompted, enter a name for thehub and your mobile device and then tap[OK].R The hub name setting is used by your

mobile device to identify the hub. Thisis useful when you have multiple hubs.

R The mobile device name setting isused by the hub and other systemusers to identify your mobile device.This is useful when performing certainoperations, such as deregistering ormaking intercom calls using a cordlesshandset.

8 When prompted, select whether you wantto customize device profiles, i.e., thedevice name, location, and other settingsfor your devices.R If you choose not to customize the

device profiles now, you can changethem later if desired. For details about

customizing device profiles, refer to theUser’s Guide (page 17).

R If you choose to customize the deviceprofiles now, change each setting asdesired. When finished, press yourdevice’s “back” button repeatedly untilthe “completed” message is displayed.


Information about Wi-FicommunicationThe hub uses Wi-Fi to communicate with yourwireless router. Refer to the followinginformation when planning where to place thehub.

Do not use the hub in the following areas orlocations. Malfunction or interference to radiocommunication may result.R Indoor areas that have certain types of

radio or mobile communications equipmentR Locations near microwave ovens or

Bluetooth devicesR Indoor areas where antitheft devices or

2.4 GHz frequency devices such as POSsystems are used

Do not place the hub in areas where thefollowing materials or objects are locatedbetween the hub and the wireless router.These materials and objects may interferewith wireless communication or causewireless transmission speed to become slower.R Metallic doors or shuttersR Walls containing aluminum-sheet insulationR Walls made of concrete, stone, brick, or tinR Multiple wallsR Steel shelvingR Fireproof glass


Setup

HNB600_(en_en)_0124_ver.201.pdf 14 2017/01/25 10:22:35

Registering another mobiledeviceIn order to access the system from a mobiledevice, you must first register the mobiledevice to the hub. You can register up to 8mobile devices to a hub.Confirm the following before you begin.– Make sure you have completed the initial

setup procedure– Make sure your mobile device can connect

to the Internet– Make sure your wireless router and the hub

are turned on– Make sure your mobile device and the hub

are connected to the same wireless router1 Using the mobile device that you want to

register, download the [Home Network]app and then start the app.R If prompted, follow the on-screen

instructions and select the appropriateregion/country.


2 When prompted, tap [Add This MobileDevice].

3 When prompted, press MWi-Fi SETUPNon the hub.R Your mobile device will be registered


instructions and enter the password usedto log in to the hub while away from home.

5 When prompted, enter a name for yourmobile device and then tap [OK].R This setting allows you to change the

name assigned to your device. It canhelp you identify your mobile devicewhen performing certain operations,such as deregistering or makingintercom calls using a cordlesshandset.


Registering other devicesto the hubThis procedure is not required for devicesthat were included as part of a bundle.

Before you can use devices such as cameras,sensors, and smart plugs, they must beregistered to the hub.If you purchased devices separately (i.e., notas part of a bundle), you must register eachdevice to the hub.

You can register each device by using theregistration buttons or the [Home Network]app.

Using registration buttons1 Hub:

Press and hold the registration buttonuntil the LED indicator blinks slowly ingreen.R Press and hold the appropriate

registration button (page 10) accordingto the device you want to register.M HANDSET/LOCATORN: ForhandsetsM CAMERAN: For camerasM OTHER DEVICEN: For otherdevices

2 Handset:Place the handset on the charger.Devices other than handset:Press and hold the device’s registrationbutton until the device’s LED indicatorblinks slowly in green.R When registration is complete, the hub

sounds one long beep.Note:R If registration fails, the hub sounds several

short beeps.R To register a mobile device, use the

procedure described on page 15.

Using the app1 Start the [Home Network] app.


Setup

HNB600_(en_en)_0124_ver.201.pdf 15 2017/01/25 10:22:35

2 From the [Home Network] app homescreen, tap [Settings].

3 Tap [Device Registration].4 Tap [Registration].5 Select the type of device that you want to

register.6 Handset:

Place the handset on the charger.Devices other than handset:Press and hold the registration button onthe device you want to register until thedevice’s LED indicator blinks slowly ingreen.R When registration is complete, the hub

sounds one long beep.Note:R If registration fails, the hub sounds several

short beeps.


Setup

HNB600_(en_en)_0124_ver.201.pdf 16 2017/01/25 10:22:35

Wireless communicationrange (DECT)The wireless communication range of eachdevice in the system from the hub isapproximately 50 m (160 feet) indoors andapproximately 300 m (1,000 feet) outdoors.Wireless communication may be unreliablewhen the following obstacles are locatedbetween the hub and other system devices.R Metal doors or screensR Walls containing aluminum-sheet insulationR Walls made of concrete or corrugated ironR Double-pane glass windowsR Multiple wallsR When using each device on separate floors

or in different buildings

Accessing the User’s GuideThe User’s Guide is a collection of onlinedocumentation that helps you get the most outof the [Home Network] app.1 iPhone/iPad

Tap in the app’s home screen.Android devicesTap or press your mobile device’smenu button in the app’s home screen.

2 Tap [User’s Guide].Note:R Microsoft® Windows® Internet Explorer® 8

and earlier versions are not supported.R Android 4.1 or later versions are

recommended.R You can also access the User’s Guide at

the web page listed below.

www.panasonic.net/pcc/support/tel/homenetwork/manual/


Appendix

HNB600_(en_en)_0124_ver.201.pdf 17 2017/01/25 10:22:35

Wall mountingYou can use the included wall mountingadaptor to wall mount the hub if desired.Note:R Make sure that the wall and the fixing

method are strong enough to support theweight of the unit.

1 Connect the AC adaptor and thetelephone line cord to the hub.R Secure the AC adaptor cord by

wrapping it around the hook.

2 Slide the wall mounting adaptor up until itclicks into place.R Make sure the “UP” mark on the wall

mounting adaptor faces upwards.R Align and insert the tabs (1) of the

wall mounting adaptor to the grooves(2) of the hub.

UP

12

UP

UP


Appendix

HNB600_(en_en)_0124_ver.201.pdf 18 2017/01/25 10:22:35

3 Mount the hub on a wall then slide downto secure in place.R Pass the AC adaptor cord and the

telephone line cord through the groove(1) in the wall mounting adaptor.Wrap up the telephone line cord asshown to prevent the cord from beingpinched.

R This product is compliant with thefollowing wall phone plate sizes (2types).2 83 mm (3 1/4 inches)3 102 mm (4 inches)

R Fit the slots of the hub onto thecorresponding wall phone plate tabsfor (4) and (5) respectively.

5

23

4

5

41

Removing the wall mounting adaptorWhile pushing the release levers (A) awayfrom the center of the wall mounting adaptor,slide the adaptor down (B).

A A

B


Appendix

HNB600_(en_en)_0124_ver.201.pdf 19 2017/01/25 10:22:35

SpecificationsR Standards

DECT:DECT (Digital Enhanced CordlessTelecommunications)Wi-Fi:IEEE 802.11b/g/n

R Frequency rangeDECT:1.92 GHz – 1.93 GHzWi-Fi:2.412 GHz – 2.462 GHz (channels 1 – 11)

R RF transmission powerDECT:115 mW (max.)Wi-Fi:100 mW (peak transmission power)

R EncryptionWPA2™-PSK (TKIP/AES), WPA™-PSK(TKIP/AES), WEP (128/64 bit)

R Simplified configurationWPS (PBC)

R Power source120 V AC, 60 Hz

R Power consumptionStandby: Approx. 3.5 WMaximum: Approx. 4.0 W

R Operating conditions0 °C – 40 °C (32 °F – 104 °F)20 % – 80 % relative air humidity (dry)

R Alert tone volumeHigh alert level: approx. 90 dBLow alert level: approx. 73 dB(measured approx. 10 cm (3 15/16 inches)in front of the center of the unit)

R Dimensions (height × width × depth)Approx. 42 mm ´ 130 mm ´ 130 mm(1 21/32 inches ´ 5 1/8 inches ´5 1/8 inches)

R Mass (weight)Approx. 220 g (0.49 lb)

Open source softwarenoticeR Parts of this product use open source

software supplied based on the relevantconditions of the Free SoftwareFoundation’s GPL and/or LGPL and otherconditions. Please read all licenceinformation and copyright notices related tothe open source software used by thisproduct. This information is available at thefollowing web page:www.panasonic.net/pcc/support/tel/homenetwork/At least three (3) years from delivery of thisproduct, Panasonic Corporation will give toany third party who contacts us at thecontact information provided below, for acharge of no more than the cost ofphysically distributing source code, acomplete machine-readable copy of thecorresponding source code and thecopyright notices covered under the GPLand the LGPL. Please note that softwarelicensed under the GPL and the LGPL isnot under warranty.www.panasonic.net/pcc/support/tel/homenetwork/

Software informationR The End User License Agreement (EULA)

for the Home Network app is available atthe following web page:www.panasonic.net/pcc/support/tel/homenetwork/


Appendix

HNB600_(en_en)_0124_ver.201.pdf 20 2017/01/25 10:22:35

FCC and other informationThis equipment complies with Part 68 of theFCC rules and the requirements adopted bythe ACTA. On the bottom of this equipment isa label that contains, among other information,a product identifier in the formatUS:ACJ----------.If requested, this number must be provided tothe telephone company.R Registration No.............(found on the

bottom of the unit)R Ringer Equivalence No. (REN).......0.1B

A plug and jack used to connect thisequipment to the premises wiring andtelephone network must comply with theapplicable FCC Part 68 rules andrequirements adopted by the ACTA. Acompliant telephone cord and modular plug isprovided with the product. It is designed to beconnected to a compatible modular jack that isalso compliant.

The REN is used to determine the number ofdevices that may be connected to a telephoneline. Excessive RENs on a telephone line mayresult in the devices not ringing in response toan incoming call. In most but not all areas, thesum of RENs should not exceed five (5.0). Tobe certain of the number of devices that maybe connected to a line, as determined by thetotal RENs, contact the local telephonecompany. For products approved after July23, 2001, the REN for the product is part ofthe product identifier that has the formatUS:AAAEQ##TXXXX. The digits representedby ## are the REN without a decimal point(e.g., 03 is a REN of 0.3).

If this equipment causes harm to thetelephone network, the telephone companywill notify you in advance that temporarydiscontinuance of service may be required.But if advance notice isn’t practical, thetelephone company will notify the customer assoon as possible. Also, you will be advised ofyour right to file a complaint with the FCC ifyou believe it is necessary.

The telephone company may make changesin its facilities, equipment, operations orprocedures that could affect the operation ofthe equipment. If this happens the telephonecompany will provide advance notice in orderfor you to make necessary modifications tomaintain uninterrupted service.

If trouble is experienced with this equipment,for repair or warranty information, pleasecontact a Factory Service Center or otherAuthorized Servicer. If the equipment iscausing harm to the telephone network, thetelephone company may request that youdisconnect the equipment until the problem isresolved.

Connection to party line service is subject tostate tariffs. Contact the state public utilitycommission, public service commission orcorporation commission for information.

If your home has specially wired alarmequipment connected to the telephone line,ensure the installation of this equipment doesnot disable your alarm equipment. If you havequestions about what will disable alarmequipment, consult your telephone companyor a qualified installer.

This equipment is hearing aid compatible asdefined by the FCC in 47 CFR Section 68.316.

When you hold the phone to your ear, noisemight be heard in your Hearing Aid. SomeHearing Aids are not adequately shielded fromexternal RF (radio frequency) energy. If noiseoccurs, use an optional headset accessory orthe speakerphone option (if applicable) whenusing this phone. Consult with your audiologistor Hearing Aid manufacturer about theavailability of Hearing Aids which provideadequate shielding to RF energy commonlyemitted by digital devices.

WHEN PROGRAMMING EMERGENCYNUMBERS AND(OR) MAKING TEST CALLSTO EMERGENCY NUMBERS:1. Remain on the line and briefly explain to

the dispatcher the reason for the call.


Appendix

HNB600_(en_en)_0124_ver.201.pdf 21 2017/01/25 10:22:35

2. Perform such activities in the off-peakhours, such as early morning or lateevenings.

This device complies with Part 15 of the FCCRules. Operation is subject to the followingtwo conditions:(1) This device may not cause harmfulinterference, and (2) this device must acceptany interference received, includinginterference that may cause undesiredoperation.Privacy of communications may not beensured when using this device.

CAUTION:Any changes or modifications not expresslyapproved by the party responsible forcompliance could void the user’s authority tooperate this device.

NOTE:This equipment has been tested and found tocomply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules.These limits are designed to providereasonable protection against harmfulinterference in a residential installation. Thisequipment generates, uses, and can radiateradio frequency energy and, if not installedand used in accordance with the instructions,may cause harmful interference to radiocommunications. However, there is noguarantee that interference will not occur in aparticular installation. If this equipment doescause harmful interference to radio ortelevision reception, which can be determinedby turning the equipment off and on, the useris encouraged to try to correct the interferenceby one or more of the following measures:– Reorient or relocate the receiving antenna.– Increase the separation between the

equipment and receiver.– Connect the equipment into an outlet on a

circuit different from that to which thereceiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Some devices operate at frequencies that maycause interference to nearby TVs and VCRs.To minimize or prevent such interference, this

device should not be placed near or on top ofa TV or VCR. If interference is experienced,move this device further away from the TV orVCR. This will often reduce or eliminateinterference.

FCC RF Exposure Warning:R This product complies with FCC radiation

exposure limits set forth for an uncontrolledenvironment.

R To comply with FCC RF exposurerequirements, the hub must be installedand operated 20 cm (8 inches) or morebetween the product and all person’s body.

R This product may not be collocated oroperated in conjunction with any otherantenna or transmitter.

R For body-worn operation, the device mustbe used only with a non-metallic accessory.Use of other accessories may not ensurecompliance with FCC RF exposurerequirements.

Notice:R FCC ID can be found on the bottom of the

unit.


Appendix

HNB600_(en_en)_0124_ver.201.pdf 22 2017/01/25 10:22:35

Customer services

You may also contact us directly at: 1-800-272-7033,

Monday - Friday 9 am to 9 pm;

Saturday - Sunday 10 am to 7 pm, EST.

Accessories!

http://shop.panasonic.com/support

Customer Services Directory

Shop

for all your Panasonic gearGo to

Get everything you need to get the most out of

your Panasonic products

Accessories & Parts for your Camera, Phone, A/V

products, TV, Computers & Networking, Personal

Care, Home Appliances, Headphones, Ba!eries,

Backup Chargers & more…

For Product Informa"on, Opera"ng Assistance,

Parts, Owner’s Manuals, Dealer and Service info

go to http://shop.panasonic.com/support

For the hearing or speech impaired TTY: 1- 877-833-8855

As of June 2015


Appendix

HNB600_(en_en)_0124_ver.201.pdf 23 2017/01/25 10:22:35

Limited Warranty (ONLY FOR U.S.A.)

Limited Warranty Coverage (For USA Only)

Labor

One (1) Year

Parts

One (1) Year

To submit a new repair request and for quick repair status visit our Web Site at

http://shop.panasonic.com/support

Panasonic Products Limited Warranty

Online Repair Request

Mail-In Service--Online Repair Request

If your product does not work properly because of a defect in materials or workmanship,

Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length

of the period indicated on the chart below, which starts with the date of original purchase

(“warranty period”), at its option either (a) repair your product with new or refurbished parts,

(b) replace it with a new or a refurbished equivalent value product, or (c) refund your

purchase price. The decision to repair, replace or refund will be made by the warrantor.

During the “Labor” warranty period there will be no charge for labor. During the “Parts”

warranty period, there will be no charge for parts. This Limited Warranty excludes both

parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet).

This warranty only applies to products purchased and serviced in the United States.

This warranty is extended only to the original purchaser of a new product which was

not sold “as is”.

Home Network System Products

microSD card (Included model only) 90 days N/A

When shipping the unit, carefully pack, include all supplied accessories listed in the

Owner’s Manual, and send it prepaid, adequately insured and packed well in a carton box.

When shipping Lithium Ion batteries please visit our Web Site at

http://shop.panasonic.com/support as Panasonic is committed to providing the most up to

date information. Include a letter detailing the complaint, a return address and provide a

daytime phone number where you can be reached. A valid registered receipt is required

under the Limited Warranty.

IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER WILL

BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING

DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL

BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF

OF PURCHASE.

Product or Part Name


Appendix

HNB600_(en_en)_0124_ver.201.pdf 24 2017/01/25 10:22:35

Limited Warranty Limits and Exclusions

(As examples, this excludes damages for lost time, travel to and from the servicer,

loss of or damage to media or images, data or other memory or recorded content.

The items listed are not exclusive, but for illustration only.)

This warranty ONLY COVERS failures due to defects in materials or workmanship,

and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty

ALSO DOES NOT COVER damages which occurred in shipment, or failures which

are caused by products not supplied by the warrantor, or failures which result from

accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty

installation, set-up adjustments, misadjustment of consumer controls, improper

maintenance, power line surge, lightning damage, modification, introduction of sand,

humidity or liquids, commercial use such as hotel, office, restaurant, or other business

or rental use of the product, or service by anyone other than a Factory Service Center

or other Authorized Servicer, or damage that is attributable to acts of God.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER

“LIMITED WARRANTY COVERAGE”.

THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT

OF ANY BREACH OF THIS WARRANTY.

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF

MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.

PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY,

ARE YOUR RESPONSIBILITY.

Some states do not allow the exclusion or limitation of incidental or consequential damages,

or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which vary

from state to state. If a problem with this product develops during or after the warranty period,

you may contact your dealer or Service Center. If the problem is not handled to your

satisfaction, then write to:

Consumer Affairs Department

Panasonic Corporation of North America

661 Independence Pkwy

Chesapeake, VA 23320

As of June 2015


Appendix

HNB600_(en_en)_0124_ver.201.pdf 25 2017/01/25 10:22:35

26

Notes

HNB600_(en_en)_0124_ver.201.pdf 26 2017/01/25 10:22:35

27

Notes

HNB600_(en_en)_0124_ver.201.pdf 27 2017/01/25 10:22:35

A

BMake sure the AC adaptor is connected.

If your product is not working properly. . .

IMPORTANT!

Visit our Web site: http://shop.panasonic.com/support

• FAQ and troubleshooting hints are available.

Use the Home Network app to access the User’s Guide

and refer to the Troubleshooting section.

For your future referenceWe recommend keeping a record of the following information to assist with any repair underwarranty.

Serial No. Date of purchase(found on the bottom of the unit)Name and address of dealer

Attach your purchase receipt here.

Two Riverfront Plaza, Newark, NJ 07102-5490

© Panasonic Corporation 2014

HNB600_(en_en)_0124_ver.201.pdf 28 2017/01/25 10:22:36

Guía de configuración del sistemaSistema de red doméstico

HUBModelo n° KX-HNB600

Gracias por adquirir un producto Panasonic.

Este documento explica cómo configurar el hub y cómo acceder a él desde un dispositivomóvil. Se deben seguir estos pasos para poder usar el sistema.Para obtener detalles sobre cómo usar el sistema, consulte la Guía del usuario (pági-na 10).

Lea este documento antes de usar la unidad, y guárdelo para consultarlo en el futuro.Para obtener ayuda, comuníquese con nosotros llamando al 1-800-272-7033 o visite nuestrositio web: http://shop.panasonic.com/support para clientes en los EE. UU. (solo en inglés)

Por favor, registre su producto: http://shop.panasonic.com/support

PNQX6695XA CC0814WK2126 (E)

HNB600_(es_es)_0125_ver201.pdf 1 2017/01/25 17:33:55

ConfiguraciónNombres de los componentes y funciones ..........3Led indicador ........................................................3Conexiones ..........................................................4Configuraciones de Wi-Fi® ...................................5Registro de otro dispositivo móvil ........................8Registro de otros dispositivos al hub ...................8

ApéndiceAlcance de la comunicación inalámbrica(DECT) ...............................................................10Acceso a la Guía del usuario .............................10Montaje en la pared ...........................................11

2

Tabla de Contenido

HNB600_(es_es)_0125_ver201.pdf 2 2017/01/25 17:33:55

Nombres de los componentesy funciones

C

BA

D E

G H I

F

AltavozLed indicadorClavija de corriente continuaClavija LINEMWi-Fi SETUPNSe usa durante la configuración inicial.Ranura para tarjeta microSDSe usa mientras inserta una tarjeta microSD.Retire la etiqueta cuando la inserte.M HANDSET/LOCATORNSe usa al registrar un auricular. Tambiénpuede presionar este botón para ubicar unauricular perdido.M CAMERANSe usar al registrar una cámara.M OTHER DEVICENSe usa al registrar otros dispositivos, comosensores y conectores inteligentes.

Led indicadorPuede usar el Led indicador para confirmar elestado del hub.

Indicador EstadoApagado Sin energía, o el Led

indicador está apaga-do*1

Verde, encendido Funcionamiento nor-mal, conectado al enru-tador inalámbrico*1

Verde, parpadeandolentamente

Modo de registro

Verde, parpadeo rápi-do

El hub está buscandoel enrutador inalámbri-co

Alterna entre:Verde, parpadeandolentamenteAmarillo, parpadeo len-to

El hub se está inician-do (no se puede usaraún)*2

Rojo, encendido El sistema de alarmaestá armado*1

Rojo, parpadeo rápido Se disparó el sistemade alarma

Amarillo, encendido Se debe realizar la con-figuración inicial

Amarillo, parpadeo len-to

Configuración inicialen progreso, dispositi-vo móvil conectado

Amarillo, parpadeante La configuración inicialestá arrancando

*1 Puede configurar el hub de forma tal que elLed indicador no se encienda durante elfuncionamiento normal. Para obtener másinformación, consulte la Guía del usuario(página 10).

*2 Es posible que el hub tarde un tiempo enterminar de iniciar.

Para obtener ayuda, visite http://shop.panasonic.com/support 3

Configuración

HNB600_(es_es)_0125_ver201.pdf 3 2017/01/25 17:33:55

ConexionesInserte el enchufe del adaptador de corrientefirmemente en la clavija de corriente continua.Asegure el cable del adaptador de corrientealterna enrollándolo en el gancho.Conecte el adaptador de corriente a la tomade corriente.Inserte el cable de línea telefónica en la clavijade LINE y la toma telefónica de una sola línea(RJ11C) hasta que escuche un clic.*1Solo para los usuarios de servicio DSL/ADSL: conecte su filtro DSL/ADSL (noincluido).*1Solo usuarios de Cámara exterior(KX-HNC600) o Cámara interior(KX-HNC210): retire la etiqueta que cubre laranura de la tarjeta y luego inserte la tarjetamicroSD (no se incluye) con la esquinadentada (1) hacia arriba en la ranura (2)hasta que escuche un clic.

*1 Este paso solo es necesario si desea usarfunciones de telefonía fija. Para obtenerdetalles sobre las funciones de telefonía fija,consulte la Guía del usuario (página 10).

Nota:R Use solo el adaptador de corriente alterna

Panasonic PNLV236 que se suministra.R Se necesita una tarjeta microSD (no incluida)

para grabar imágenes de cámaras.R Para extraer la tarjeta microSD, presiónela hacia

dentro primero y luego extráigala.

4

5

4

3

2

1

6

12

Nota acerca de las conexiones dealimentación

Adaptador de corriente alternaR El adaptador de corriente debe permanecer

conectado en todo momento (es normal que eladaptador se caliente durante su uso).

R El adaptador de corriente debe estar conectadoa un enchufe de corriente orientadoverticalmente o en una toma de corriente alternacolocada en el piso. No conecte el adaptador decorriente alterna a una toma de corrientemontada en el techo, ya que el peso deladaptador puede hacer que se desconecte.

4 Para obtener ayuda, visite http://shop.panasonic.com/support

Configuración

HNB600_(es_es)_0125_ver201.pdf 4 2017/01/25 17:33:55

Falla en el suministro eléctricoR El hub no funciona durante las fallas del

suministro eléctrico.R Las funciones telefónicas del hub no trabajarán

durante un corte de energía. Recomendamosque conecte un teléfono con cable que no utiliceun adaptador de CA a su línea telefónica.

Configuraciones de Wi-Fi®Después de conectar el hub, necesitará lo siguientepara acceder al sistema desde su dispositivo móvil.En este capítulo se explica cada procedimiento.1 Descarga

Descargue la aplicación [Home Network] asu dispositivo móvil.

2 Configuración inicialUse la aplicación [Home Network] paraconfigurar el hub y que se conecte alenrutador inalámbrico; a continuación, registreel dispositivo móvil en el hub.

Cómo descargar la aplicación [HomeNetwork]La información de descarga está disponible en lasiguiente página web.

www.panasonic.net/pcc/support/tel/homenetwork/

Dispositivos móviles compatiblesiPhone® 4 o posterior, iPad®, o iPad mini™ (iOS6.0 o posterior) o un dispositivo Android™ (Android 4.0 o posterior)Nota:R Es posible que la aplicación [Home Network]

no funcione correctamente dependiendo delentorno del sistema, como el modelo de sudispositivo móvil, los periféricos conectados almismo y las aplicaciones instaladas en él.

R Los siguientes dispositivos Android no soncompatibles con la aplicación [Home Network].– Dispositivos Android que no son compatibles

con Google Play– Dispositivos con Android, con características

de hardware limitadas (se requierecompatibilidad con Bluetooth, Wi-Fi ymicrófono).

Configuración inicialConfirme lo siguiente antes de comenzar.– Asegúrese de haber instalado la aplicación

[Home Network] en su dispositivo móvil– Asegúrese de que el hub y su enrutador

inalámbrico estén encendidos y que el Ledindicador del hub esté encendido en amarillo

– Asegúrese de que el hub esté ubicado dentrodel alcance del enrutador inalámbrico

– Asegúrese de que el dispositivo móvil estéconectado al enrutador inalámbrico

– Asegúrese de que su dispositivo móvil puedaconectarse a Internet

– Asegúrese de conocer el nombre de la red(SSID) y la clave que se asignó al enrutadorinalámbrico

Configuración inicial para iPhone, iPad1 Inicie la aplicación [Home Network].

R Si se le solicita, siga las instrucciones enpantalla y seleccione la región y el paísapropiados.

R Si se le solicita que seleccione eldispositivo que desea configurar, toque[Hub].

2 Cuando se le solicite, toque [Configurar elHub].


Configuración

HNB600_(es_es)_0125_ver201.pdf 5 2017/01/25 17:33:55

3 Cuando se le solicite, oprima MWi-Fi SETUPNen el hub.R El Led indicador parpadea en amarillo.

4 Cambie la configuración de Wi-Fi de sudispositivo móvil temporalmente para que seconecte directamente al hub.R Abra la aplicación [Configuración] en su

dispositivo móvil, toque [Wi-Fi], seleccione“KX-HNB600_Panasonic”, introduzca“00000000” como clave y luego toque[Conectar].

R Si aparece más de 1 elemento llamado“KX-HNB600_Panasonic”, espere aprox.10 minutos y realice este procedimientodesde el inicio.

5 Inicie de nuevo la aplicación [Home Network].6 Si es necesario, introduzca la clave requerida

para conectarse al enrutador inalámbrico y, acontinuación, presione [Sig.].R El hub y su dispositivo móvil se conectan a

su enrutador inalámbrico.R Si se le solicita, siga las instrucciones en la

pantalla y conecte su dispositivo móvil a suenrutador inalámbrico, reinicie la aplicacióny luego toque [Añadir este dispositivomóvil].

R Si introduce una clave de Wi-Fi incorrecta,aparece [La instalación ha fallado.] y elLED indicador del hub se encenderá.Proceda de la siguiente manera según elcolor del LED indicador del hub.– Si la luz del LED indicador es amarilla,

repita el procedimiento de instalacióndesde el comienzo.

– Si la luz del LED indicador parpadea enverde rápidamente, debe reiniciar laconfiguración Wi-Fi del hub. Consulte“Si el LED indicador del hub parpadeaen verde”, página 6.

7 Cuando se le solicite, oprima MWi-Fi SETUPNen el hub.R Se registrará el dispositivo móvil en el hub.

8 Cuando se le solicite, siga las instrucciones enla pantalla y establezca la clave usada paraacceder al hub mientras está fuera de sucasa. A continuación, toque [Aceptar].

9 Cuando se le solicite, introduzca un nombrepara el hub y para el dispositivo móvil y toque[Aceptar].R Su dispositivo móvil utiliza la configuración

del nombre del hub para identificar el hub.Esto resulta útil cuando tiene varios hubs.

R Los usuarios del hub y otros sistemasutilizan la configuración del nombre deldispositivo móvil para identificar sudispositivo móvil. Esto puede ser útil alrealizar ciertas operaciones, como anularel registro o realizar llamadas deintercomunicador con un auricularinalámbrico.

10 Cuando se le solicite, seleccione si deseapersonalizar perfiles de dispositivos, como elnombre del dispositivo, ubicación y otrosajustes de configuración para sus dispositivos.R Si opta por no personalizar los perfiles del

dispositivo en este momento, puedecambiarlos más tarde si lo desea. Paraobtener detalles sobre personalización deperfiles de dispositivos, consulte la Guíadel usuario (página 10).

R Si opta por personalizar los perfiles de losdispositivos en este momento, cambiecada uno de los ajustes de configuraciónsegún lo desee. Al finalizar, toque reiteradamente hasta que aparezca elmensaje “completado”.

R Aparecerá la pantalla de inicio de laaplicación una vez completada laconfiguración inicial.

Si el LED indicador del hub parpadea en verdeSi introduce una clave de Wi-Fi incorrecta duranteel procedimiento de configuración inicial paraiPhone o iPad, aparece [La instalación hafallado.] y el LED indicador del hub parpadearápidamente en verde. En este caso, realice losiguiente.1. Mantenga oprimidos al mismo tiempo los 3

botones de registro en el lateral del hub yMWi-Fi SETUPN en la parte trasera del hub (4botones en total) hasta que el Led indicador delhub parpadee lentamente en verde y amarillo.

2. Espere hasta que el Led indicador del hub semantenga en amarillo.

3. Repita el procedimiento de configuración inicial(“Configuración inicial para iPhone, iPad”,página 5).


Configuración

HNB600_(es_es)_0125_ver201.pdf 6 2017/01/25 17:33:56

Configuración inicial para dispositivosAndroid1 Inicie la aplicación [Home Network].

R Si se le solicita, siga las instrucciones enpantalla y seleccione la región y el paísapropiados.


2 Cuando se le solicite, toque [Configurar elHub].

3 Cuando se le solicite, oprima MWi-Fi SETUPNen el hub.R El Led indicador parpadea en amarillo.R La aplicación cambia temporalmente la

configuración Wi-Fi de su dispositivo móvilpara que se conecte de forma directa alhub.

4 Si es necesario, introduzca la clave requeridapara conectarse al enrutador inalámbrico y, acontinuación, presione [Sig.].R El hub y su dispositivo móvil se conectan a

su enrutador inalámbrico.5 Cuando se le solicite, oprima MWi-Fi SETUPN

en el hub.R Se registrará el dispositivo móvil en el hub.

6 Cuando se le solicite, siga las instrucciones enla pantalla y establezca la clave usada paraacceder al hub mientras está fuera de sucasa. A continuación, toque [Aceptar].

7 Cuando se le solicite, introduzca un nombrepara el hub y para el dispositivo móvil y toque[Aceptar].R Su dispositivo móvil utiliza la configuración

del nombre del hub para identificar el hub.Esto resulta útil cuando tiene varios hubs.

R Los usuarios del hub y otros sistemasutilizan la configuración del nombre deldispositivo móvil para identificar sudispositivo móvil. Esto puede ser útil alrealizar ciertas operaciones, como anularel registro o realizar llamadas deintercomunicador con un auricularinalámbrico.

8 Cuando se le solicite, seleccione si deseapersonalizar perfiles de dispositivos, como el

nombre del dispositivo, ubicación y otrosajustes de configuración para sus dispositivos.R Si opta por no personalizar los perfiles del

dispositivo en este momento, puedecambiarlos más tarde si lo desea. Paraobtener detalles sobre personalización deperfiles de dispositivos, consulte la Guíadel usuario (página 10).

R Si opta por personalizar los perfiles de losdispositivos en este momento, cambiecada uno de los ajustes de configuraciónsegún lo desee. Al finalizar, oprima elbotón “volver” reiteradamente hasta queaparezca el mensaje “completado”.


Información acerca de lacomunicación Wi-FiEl hub usa Wi-Fi para comunicarse con suenrutador inalámbrico. Consulte la siguienteinformación cuando piense en dónde colocar el hub.

No coloque el hub en las siguientes áreas oubicaciones. Es posible que existan fallas ointerferencias en la comunicación por radio.R Interiores donde haya equipos con cierto tipo de

comunicación por radio o móvilR Ubicaciones cerca de hornos microondas o

dispositivos BluetoothR Interiores donde haya dispositivos antirrobos o

dispositivos en frecuencias de 2.4 GHz como lossistemas POS

No coloque un hub en áreas donde se encuentrenlos siguientes materiales u objetos entre el hub y elenrutador inalámbrico. Dichos materiales y objetospueden interferir con la comunicación inalámbrica opueden provocar que la velocidad de transmisiónse reduzca.R Puertas metálicasR Paredes que contengan aislamiento de aluminioR Paredes de hormigón, piedra, ladrillo o estañoR Varias paredesR Repisas de aceroR Vidrio a prueba de incendios


Configuración

HNB600_(es_es)_0125_ver201.pdf 7 2017/01/25 17:33:56

Registro de otro dispositivomóvilPara acceder al sistema desde un dispositivo móvil,primero debe registrarlo en el hub. Puede registrarhasta 8 dispositivos móviles en un hub.Confirme lo siguiente antes de comenzar.– Asegúrese de haber completado el

procedimiento de configuración inicial– Asegúrese de que su dispositivo móvil pueda

conectarse a Internet– Asegúrese de que el el enrutador inalámbrico y

el hub estén encendidos– Asegúrese de que el dispositivo móvil y el hub

estén conectados al mismo enrutador1 Desde el dispositivo móvil que desea registrar,

descargue la aplicación [Home Network] yluego iníciela.R Si se le solicita, siga las instrucciones en

pantalla y seleccione la región y el paísapropiados.


2 Cuando se le solicite, toque [Añadir estedispositivo móvil].

3 Cuando se le solicite, oprima MWi-Fi SETUPNen el hub.R Se registrará el dispositivo móvil en el hub.

4 Cuando se le solicite, siga las instrucciones enla pantalla e introduzca la clave usada paraacceder al hub.

5 Cuando se le solicite, introduzca un nombrepara el dispositivo móvil y toque [Aceptar].R Esta configuración le permite cambiar el

nombre asignado a este dispositivo. Estopuede ser útil para identificar el dispositivomóvil cuando realice ciertas operaciones,como anular el registro o realizar llamadasde intercomunicación con un auricularinalámbrico.


Registro de otros dispositivosal hub

Este procedimiento no es necesario para unida-des que son parte de un paquete.

Antes de poder usar dispositivos como cámaras,sensores y conectores inteligentes, se debenregistrar en el hub.Si compró los dispositivos por separado (es decir,no como parte de un paquete), debe registrar cadadispositivo en el hub.

Puede registrar cada unidad mediante los botonesde registro o la aplicación [Home Network].

Uso de los botones de registro1 Hub:

Oprima y mantenga oprimido el botón deregistro hasta que el Led indicador parpadeelentamente en verde.R Oprima y mantenga oprimido el botón de

registro correspondiente (página 3) enfunción del dispositivo que desea registrar.M HANDSET/LOCATORN: ParaauricularesM CAMERAN: Para cámarasM OTHER DEVICEN: Para otrosdispositivos

2 Auricular:Coloque el auricular en el cargador.Dispositivos que no sean auriculares:Mantenga presionado el botón de registro deldispositivo hasta que el Led indicadorparpadee lentamente en verde.R Cuando se ha completado el registro, el

hub emitirá un pitido largo.Nota:R Si el registro falla, el hub emitirá varios pitidos

cortos.R Para registrar un dispositivo móvil, use el

procedimiento descrito en página 8


Configuración

HNB600_(es_es)_0125_ver201.pdf 8 2017/01/25 17:33:56

Uso de la aplicación1 Inicie la aplicación [Home Network].2 Desde la pantalla de inicio de la aplicación

[Home Network], toque [Configuración].3 Toque [Registro de dispositivos].4 Toque [Registro].5 Seleccione el tipo de dispositivo que desea

registrar.6 Auricular:

Coloque el auricular en el cargador.Dispositivos que no sean auriculares:Mantenga presionado el botón de registro deldispositivo que desea registrar hasta que elLed indicador parpadee lentamente en verde.R Cuando se ha completado el registro, el

hub emitirá un pitido largo.Nota:R Si el registro falla, el hub emitirá varios pitidos

cortos.


Configuración

HNB600_(es_es)_0125_ver201.pdf 9 2017/01/25 17:33:56

Alcance de la comunicacióninalámbrica (DECT)El alcance de la comunicación inalámbrica de cadadispositivo en el sistema del hub es deaproximadamente 50 m (160 pies) en interiores yde aproximadamente 300 m (1,000 pies) en elexterior. Es posible que la comunicacióninalámbrica no sea tan confiable cuando seencuentran los obstáculos siguientes entre el hub yotros dispositivos del sistema.R Puertas o pantallas metálicasR Paredes que contengan aislamiento de aluminioR Paredes de hormigón o hierro corrugadoR Ventanas de vidrio dobleR Varias paredesR Cuando los dispositivos están en pisos o

edificios diferentes

Acceso a la Guía del usuarioLa Guía del usuario es una colección dedocumentación en línea que lo ayuda a aprovecharal máximo la aplicación [Home Network].1 iPhone/iPad

Toque en la pantalla de inicio de laaplicación.Dispositivos AndroidToque u oprima el botón menú de sudispositivo en la pantalla de inicio de laaplicación.

2 Toque [Guía del Usuario].Nota:R No se admite Microsoft® Windows® Internet

Explorer® 8 y versiones anteriores.R Se recomienda Android 4.1 y versiones

posteriores.R También puede acceder a la Guía del usuario

mediante la página web a continuación.

www.panasonic.net/pcc/support/tel/homenetwork/manual/


Apéndice

HNB600_(es_es)_0125_ver201.pdf 10 2017/01/25 17:33:56

Montaje en la paredPuede usar el adaptador de instalación en paredincluido para instalar el hub de dicha forma si lodesea.Nota:R Asegúrese de que la pared y el método de

colocación sean lo suficientemente resistentespara soportar el peso de la unidad.

1 Conecte el adaptador de corriente y el cablede línea telefónica al hub.R Asegure el cable del adaptador de

corriente alterna enrollándolo en el gancho.

2 Deslice el adaptador de instalación en paredhasta que encaje y haga clic.R Asegúrese de que la marca “UP” en el

adaptador de instalación en pared mirehacia arriba.

R Alinee e inserte las pestañas (1) deladaptador de instalación en pared en lasranuras (2) del hub.

UP

12

UP

UP


Apéndice

HNB600_(es_es)_0125_ver201.pdf 11 2017/01/25 17:33:56

3 Monte el hub en la pared y deslícelo paraasegurarlo en su sitio.R Pase el cable del adaptador de corriente y

el de la línea telefónica por la ranura (1)en el adaptador de instalación en pared.Enrolle el cable de línea telefónica como semuestra para evitar que se quede pillado.

R Este producto es compatible con lossiguientes tamaños de placas de losteléfonos (tipos 2).2 83 mm (3 1/4 pulgadas)3 102 mm (4 pulgadas)

R Ajuste las ranuras del hub en las pestañascorrespondientes de la placa del teléfono(4) y (5) respectivamente.

5

23

4

5

41

Extracción del adaptador de instalaciónen paredMientras aleja las palancas de desbloqueo (A) deladaptador de instalación en pared, deslice eladaptador hacia abajo (B).

A A

B


Apéndice

HNB600_(es_es)_0125_ver201.pdf 12 2017/01/25 17:33:56

Documents

System Setup Guide - Panasonichelp.panasonic.ca/viewing/ALL/KX-HN6000/OI/HNB600_PNQX... · 2017-06-14 · System Setup Guide Home Network System HUB Model No. KX-HNB600 Thank you