Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
Hytrol Conveyor Catalog02012015
HY
TR
OL
CO
NV
EY
OR
CO
MP
AN
Y, IN
C.
14.23
Single Powered Pivot diverter
CAPACITY–75 lbs. maximum package weight.
PACKAGE SIZE–Minimum 6 in. wide x 9 in. long, maximum 12 in. wide x 21 in. long. NOTE: Small packages must not be top heavy.
DIVERTER SPEED–AC Drive 42-420 FPM.
DIVERTER MECHANISM–Two rows of 3 1/8 in. dia. wheels with urethane treads driven by 3/8 in. dia. urethane belts.
MOUNTING–Complete unit bolts to 138-ACC 13 in. to 22 in. BR only or 190-ACC 13 in. to 21 in. BR, RH or LH diversion 30˚ spur discharge (spur not included). Minimum elevation 15 in. (138-ACC) or 16 in. (190-ACC). NOTE: ACC belt must be opposite discharge side. Widths over 22 in. BR contact Factory.
CYCLES–Up to 40 times per minute.
DRIVE–1/2 HP motor with AC type variable speed controller. Select 230V–3 Ph. 60 Hz. or 115V–1 Ph. 60 Hz. power.
AIR CYLINDER–1 1/4 in. dia. bore x 1 in. stroke, double acting with internal rubber bumpers both ends.
AIR VALVE–Single solenoid 4-way valve with speed controls,1/4 in. NPT valve ports. Requires maintained electrical signal of 115V–1 Ph. 60 Hz. from photo cell, limit switch, etc. (not supplied). Diverter will stay in diverted position until signal is broken. Current consumption is .09 amps holding.
AIR REQUIREMENTS–Minimum pressure 60 P.S.I., maximum 125 P.S.I., free air consumption at 60 P.S.I., .014 cu. ft. per cycle.NOTE: To eliminate contaminants in air supply line, a filter-regulator should be installed prior to the air valve (not supplied as standard).
The Powered Pivot Diverter is designed for use with Models 138-ACC & 190-ACC Accumulating Conveyor. Products are automatically diverted onto adjacent 30˚ spur lines.
5-1/4"
CENTERLINE OF DRIVEWHEEL SHAFT
"ACC" DRIVE BELT
FLOW
FLOW
30˚
MIN. TO DISCHARGEEND OF SECTION
21"
MIN. TO INFEEDEND OF SECTION
21" FLOW
"ACC" DRIVE BELT
L.H.SPUR
R.H.DIVERTER
L.H.DIVERTER
R.H.SPUR
• Standard SpecificationS
SyStemS acceSSorieS
double Powered Pivot diverterThe Double Powered Pivot Diverter is designed for use with Models 138-ACC & 190-ACC Accumulating Conveyor. Products are automatically diverted onto adjacent 30˚ spur lines.
"ACC" DRIVE BELT
R.H.SPUR
L.H.SPUR
L.H.DIVERTER
R.H.DIVERTER
9"MIN. TO DISCHARGE
END OF SECTION21"
MIN. TO INFEEDEND OF SECTION
21" FLOW
5-1/4"
CENTERLINE OF DRIVEWHEEL SHAFT
"ACC" DRIVE BELT
FLOW
FLOW
30˚
CAPACITY–75 lbs. maximum package weight.
PACKAGE SIZE–Minimum 6 in. wide x 9 in. long maximum 34 in. wide x 46 in. long. NOTE: Small packages must not be top heavy.
DIVERTER SPEED–AC Drive 42-420 FPM.
DIVERTER MECHANISM–Four rows of 3 1/8 in. dia. wheels with urethane treads driven by 3/8 in. dia. urethane belts.
MOUNTING–Complete unit bolts to 138-ACC 13 in. to 22 in. BR only or 190-ACC 13 in. to 39 in. BR, RH or LH Diversion 30˚ spur discharge (spur not included). Minimum elevation 15 in. (138-ACC) or 16 in. (190-ACC). NOTE: ACC belt must be opposite discharge side. Widths over 22 in. BR, contact Factory.
CYCLES–Up to 40 times per minute.
DRIVE–1/2 HP motor with AC type variable speed controller. Select 230V–3 Ph. 60 Hz. or 115V–1 Ph. 60 Hz. power.
AIR CYLINDER–1 1/4 in. dia. bore x 1 in. stroke, double acting with internal rubber bumpers both ends.
AIR VALVE–Single solenoid 4-way valve with speed controls. 1/4 in. NPT valve ports. Requires maintained electrical signal of 115 V–1 Ph. 60 Hz. from photo cell, limit switch, etc. (not supplied). Diverter will stay in diverted position until signal is broken. Current consumption is .09 amps holding.
AIR REQUIREMENTS–Minimum pressure 60 P.S.I., maximum 125 P.S.I. Free air consumption at 60 P.S.I., .028 cu. ft. per cycle. NOTE: To eliminate contaminants in air supply line, a filter-regulator should be installed prior to the air valve (not supplied as standard).
• Standard SpecificationS
HY
TR
OL
CO
NV
EY
OR
CO
MP
AN
Y,
INC
.
Hytrol Conveyor Catalog02012015
14.24
SyStemS acceSSorieS
CAPACITY–75 lbs. maximum package weight.
PACKAGE SIZE–Minimum 4 in. wide x 6 in. long, maximum 26 in. wide x 36 in. long. NOTE: Small packages must not be top heavy. NOTE: Product must be justified to divert side.
DIVERTER SPEED– 50-200 FPM set on Motor Controller
DIVERTER MECHANISM–Two rows of 3 1/8 in. dia. wheels with urethane treads driven by 3/8 in. dia. urethane belts.
MOUNTING–Bolts to 190-E24 15 in. to 39 in. BR, RH or LH diversion 30˚ spur discharge (spur not included). Minimum elevation 14 in. NOTE: O-rings must be opposite discharge side. Widths over 39 in. BR contact factory.
CYCLES–Up to 40 times per minute.
MOTOR–24 VDC motor, 3 amps per motor, one each Divert Bank.
MOTOR CONTROLLER– Controls and Protects Motor, one each Divert Bank.
AIR CYLINDER–1 1/4 in. dia. bore x 2 in. stroke, double acting with internal rubber bumpers both ends.
AIR VALVE–Single solenoid 4-way valve with speed controls,1/8 in. NPT valve ports. Requires main-tained electrical signal of 24VDC watt from photo cell, limit switch, etc. (not supplied). Diverter will stay in diverted position until signal is broken. Current consumption is .32 amps holding.
AIR REQUIREMENTS–Minimum pressure 60 P.S.I., maximum 125 P.S.I., free air consumption at 60 P.S.I., .064 cu. ft. per cycle.NOTE: To eliminate contaminants in air supply line, a filter-regulator should be installed prior to the air valve (not supplied as standard).
CAPACITY–75 lbs. maximum package weight.
PACKAGE SIZE–Minimum 4 in. wide x 6 in. long, maximum 26 in. wide x 36 in. long. NOTE: Small packages must not be top heavy. NOTE: Product must be justified to divert side.
DIVERTER SPEED– 50-200 FPM set on Motor Controller
DIVERTER MECHANISM–One row of 3 1/8 in. dia. wheels with urethane treads driven by 3/8 in. dia. urethane belts.
MOUNTING–Complete unit bolts to 190-E24 15 in. to 21 in. BR, RH or LH diversion 30˚ spur dis-charge (spur not included). Minimum elevation 14 in. NOTE: O-rings must be opposite discharge side. Widths over 39 in. BR contact factory.
CYCLES–Up to 40 times per minute.
MOTOR–24 VDC motor, 3 amps per motor, one each Divert Bank.
MOTOR CONTROLLER– Controls and Protects Motor, one each Divert Bank.
AIR CYLINDER–1 1/4 in. dia. bore x 2 in. stroke, double acting with internal rubber bumpers both ends.
AIR VALVE–Single solenoid 4-way valve with speed controls,1/8 in. NPT valve ports. Requires main-tained electrical signal of 24VDC watt from photo cell, limit switch, etc. (not supplied). Diverter will stay in diverted position until signal is broken. Current consumption is .32 amps holding.
AIR REQUIREMENTS–Minimum pressure 60 P.S.I., maximum 125 P.S.I., free air consumption at 60 P.S.I., .032 cu. ft. per cycle.NOTE: To eliminate contaminants in air supply line, a filter-regulator should be installed prior to the air valve (not supplied as standard).
e24 Single Powered Pivot diverter
ECN
DWG NO
DESIGNED BY
CHECKED BY
HYTROL
JONESBORO, ARKANSASCONVEYOR CO., INC.
HYTROL
DATE
DATE
MODELS
STANDARD TOLERANCESUNLESS OTHERWISE SPECIFIED
FRACTIONS ±1/64DECIMALS ±.005
ANGLES ±1°
8/18/2011
THIS DRAWING CONTAINS CONFIDENTIAL DESIGNS AND INFORMATION WHICH ARE THE PROPERTY OF HYTROL CONVEYOR COMPANY INC. THIS DRAWING AND THE INFORMATION CONTAINED HEREIN MAY NOT BE DISCLOSED OR DUPLICATED IN
WHOLE OR PART, UTILIZED IN ANY OTHER WORK, OR USED FOR MANUFACTURE OF DESIGNS WITHOUT THE PRIOR WRITTEN
PERMISSION OF HYTROL CONVEYOR COMPANY INC.
DRAWN BY DATE 8/19/2011
PAINT CLASS REVISIONSPARE PART MFG CLASS
CCatalog-Int
kchurchillkchurchill
MIN. TO DISCHARGEEND OF SECTION
4-1/2"
MIN. TO INFEEDEND OF SECTION
7-1/2"
ECN
DWG NO
DESIGNED BY
CHECKED BY
HYTROL
JONESBORO, ARKANSASCONVEYOR CO., INC.
HYTROL
DATE
DATE
MODELS
STANDARD TOLERANCESUNLESS OTHERWISE SPECIFIED
FRACTIONS ±1/64DECIMALS ±.005
ANGLES ±1°
8/18/2011
THIS DRAWING CONTAINS CONFIDENTIAL DESIGNS AND INFORMATION WHICH ARE THE PROPERTY OF HYTROL CONVEYOR COMPANY INC. THIS DRAWING AND THE INFORMATION CONTAINED HEREIN MAY NOT BE DISCLOSED OR DUPLICATED IN
WHOLE OR PART, UTILIZED IN ANY OTHER WORK, OR USED FOR MANUFACTURE OF DESIGNS WITHOUT THE PRIOR WRITTEN
PERMISSION OF HYTROL CONVEYOR COMPANY INC.
DRAWN BY DATE 8/19/2011
PAINT CLASS REVISIONSPARE PART MFG CLASS
CCatalog-Int
kchurchillkchurchill• Standard SpecificationS
e24 double Powered Pivot diverterThe Double Powered Pivot Diverter is designed for use with Models 190-E24 & 190-E24EZ Accumulating Conveyor. Products are automatically diverted onto adjacent 30˚ spur lines.
• Standard SpecificationS
ECN
DWG NO
DESIGNED BY
CHECKED BY
HYTROL
JONESBORO, ARKANSASCONVEYOR CO., INC.
HYTROL
DATE
DATE
MODELS
STANDARD TOLERANCESUNLESS OTHERWISE SPECIFIED
FRACTIONS ±1/64DECIMALS ±.005
ANGLES ±1°
8/18/2011
THIS DRAWING CONTAINS CONFIDENTIAL DESIGNS AND INFORMATION WHICH ARE THE PROPERTY OF HYTROL CONVEYOR COMPANY INC. THIS DRAWING AND THE INFORMATION CONTAINED HEREIN MAY NOT BE DISCLOSED OR DUPLICATED IN
WHOLE OR PART, UTILIZED IN ANY OTHER WORK, OR USED FOR MANUFACTURE OF DESIGNS WITHOUT THE PRIOR WRITTEN
PERMISSION OF HYTROL CONVEYOR COMPANY INC.
DRAWN BY DATE 8/19/2011
PAINT CLASS REVISIONSPARE PART MFG CLASS
CCatalog-Int
kchurchillkchurchill
ECN
DWG NO
DESIGNED BY
CHECKED BY
HYTROL
JONESBORO, ARKANSASCONVEYOR CO., INC.
HYTROL
DATE
DATE
MODELS
STANDARD TOLERANCESUNLESS OTHERWISE SPECIFIED
FRACTIONS ±1/64DECIMALS ±.005
ANGLES ±1°
8/18/2011
THIS DRAWING CONTAINS CONFIDENTIAL DESIGNS AND INFORMATION WHICH ARE THE PROPERTY OF HYTROL CONVEYOR COMPANY INC. THIS DRAWING AND THE INFORMATION CONTAINED HEREIN MAY NOT BE DISCLOSED OR DUPLICATED IN
WHOLE OR PART, UTILIZED IN ANY OTHER WORK, OR USED FOR MANUFACTURE OF DESIGNS WITHOUT THE PRIOR WRITTEN
PERMISSION OF HYTROL CONVEYOR COMPANY INC.
DRAWN BY DATE 8/18/2011
PAINT CLASS REVISIONSPARE PART MFG CLASS
CCatalog60inch-Int
kchurchillkchurchill
MIN. TO DISCHARGEEND OF SECTION
7-1/2"
6 MIN. TO INFEEDEND OF SECTION
7-1/2"
ECN
DWG NO
DESIGNED BY
CHECKED BY
HYTROL
JONESBORO, ARKANSASCONVEYOR CO., INC.
HYTROL
DATE
DATE
MODELS
STANDARD TOLERANCESUNLESS OTHERWISE SPECIFIED
FRACTIONS ±1/64DECIMALS ±.005
ANGLES ±1°
8/18/2011
THIS DRAWING CONTAINS CONFIDENTIAL DESIGNS AND INFORMATION WHICH ARE THE PROPERTY OF HYTROL CONVEYOR COMPANY INC. THIS DRAWING AND THE INFORMATION CONTAINED HEREIN MAY NOT BE DISCLOSED OR DUPLICATED IN
WHOLE OR PART, UTILIZED IN ANY OTHER WORK, OR USED FOR MANUFACTURE OF DESIGNS WITHOUT THE PRIOR WRITTEN
PERMISSION OF HYTROL CONVEYOR COMPANY INC.
DRAWN BY DATE 8/18/2011
PAINT CLASS REVISIONSPARE PART MFG CLASS
CCatalog
kchurchillkchurchill
ECN
DWG NO
DESIGNED BY
CHECKED BY
HYTROL
JONESBORO, ARKANSASCONVEYOR CO., INC.
HYTROL
DATE
DATE
MODELS
STANDARD TOLERANCESUNLESS OTHERWISE SPECIFIED
FRACTIONS ±1/64DECIMALS ±.005
ANGLES ±1°
8/18/2011
THIS DRAWING CONTAINS CONFIDENTIAL DESIGNS AND INFORMATION WHICH ARE THE PROPERTY OF HYTROL CONVEYOR COMPANY INC. THIS DRAWING AND THE INFORMATION CONTAINED HEREIN MAY NOT BE DISCLOSED OR DUPLICATED IN
WHOLE OR PART, UTILIZED IN ANY OTHER WORK, OR USED FOR MANUFACTURE OF DESIGNS WITHOUT THE PRIOR WRITTEN
PERMISSION OF HYTROL CONVEYOR COMPANY INC.
DRAWN BY DATE 8/18/2011
PAINT CLASS REVISIONSPARE PART MFG CLASS
CCatalog
kchurchillkchurchill
RHSpur
RHSpur
LHSpur
LHSpur
RH DiverterLH Diverter
The Powered Pivot Diverter is designed for use with Models 190- E24 & 190-E24EZ Conveyor. Products are automatically diverted onto adjacent 30˚ spur lines.
RH DiverterLH Diverter
Hytrol Conveyor Catalog05072015
HY
TR
OL
CO
NV
EY
OR
CO
MP
AN
Y, IN
C.
14.25
SyStemS acceSSorieSe24 electric poweredPivot diverterThe E24 Powered Pivot Diverter is designed for use with Models E24 & E24EZ Accumulating Conveyor. Products are diverted onto adjacent 30˚ spur lines. The electric linear actuator rotates the diverter sheave assembly to divert at a 30˚ angle. The vertical lift of the sheave assembly allows the diverter to have more control of the package which provides a more positive divert.
4 1/2" MIN
7
4 1/2" MIN
7" ± 1"
30
7" ± 1"
30
CAPACITY–75 lbs. maximum package weight.
PACKAGE SIZE–Minimum 4 in. wide x 6 in. long, maximum 26 in. wide x 36 in. long. NOTE: Small packages must not be top heavy.
DIVERTER SPEED–24VDC, 35-155 FPM.
DIVERTER MECHANISM–Row of 2 3/4 in. dia. wheels with urethane treads driven by 3/16 in. dia. urethane belts.
CYCLES–Up to 30 cases per minute.
MOTOR–24VDC motor, 3 amps per motor.
CONTROLS INPUT–18-24V at 1.9-4.2mA
DRIVE CURRENT REQUIREMENTS–20-28V DC 4 AMP
AVAILAbLE wIDTHS –22”, 24”, 26”, 28”, 30” OAW
• Standard SpecificationS
24TMe
lH diverterrH diverter