Upload
prasannan-d-civil
View
217
Download
0
Embed Size (px)
Citation preview
7/25/2019 take off4
1/10
7. TAKEOFF
7.1 About the Takeoff Page
The takeoff page contains all drawings that have been imported into the software, as well as all
takeoffs performed. The screen is divided into the navigation pane on the left and the takeoff areawith the drawing and takeoff displayed on the right.
Navigation Pane
On the left side of the screen is the navigation pane. The navigation pane gives you quick access
to drawings, takeoffs and an area to input or measure dimensions.
Takeoff Pane
The takeoff pane on the right displays the selected drawing and any takeoffs that have been
performed on the drawing. The software gives you the ability to measure lengths, areas and counts
and they can be taken off using both digital plans and a mouse or traditional paper plans and adigitizer. The system allows you to color-code the takeoffs in order to label various materials, and
the takeoff quantities are always displayed for quick reference.
7.2 Navigation Pane
The navigation pane for the takeoff has three possible sections, including the Eplorer, a
!roperties section and a "avigator. The right mouse menu has options that allow you to turn the
properties and navigator panels on and off.
7/25/2019 take off4
2/10
Drawings
The drawings section displays the drawings that have been imported for the estimate. There is no limit to the
number of drawings or takeoffs performed per drawing.
Takeoffs
The takeoff section represents the material takeoffs for the selected drawing.
Dimensions
The dimensions section displays all necessary dimensions for the selected takeoff. These dimensions aretaken of rom the drawing digitally, or entered manuallywhen appropriate.
7. Takeoff PaneThe takeoff pane displays the selected drawing and any takeoffs performed on that drawing.
7/25/2019 take off4
3/10
The takeoff quantities can be displayed for quick reference. #n addition to maintaining a separate set of
quantities by takeoff layer, you can also assign a color, area fill style, line style and count image to each takeoff.
The color of the shading is the same as the line color selected for that takeoff layer.
The takeoff properties are edited at either the formula list, if a formula is being used, or the unit of
measure list if a formula is not being utilized.
7.! "m#ort Drawings
To import drawings into your estimate, select the #mport option on the Takeoff menu tab.
$hoose the desired drawing files and click on the Open button.
7/25/2019 take off4
4/10
7.$ Perform a Takeoff
To perform a takeoff, first open the database screen and find the desired item or assembly.
To start a takeoff, press the Enter key or double-click your mouse on the desired item or assembly.
7/25/2019 take off4
5/10
The red block in the takeoff column for the assembly below means that it is already setup to perform a takeoff.
%elect an eisting drawing or click on the #mport &rawing option under the Takeoff &rawing section on thebottom of the database screen.
The assembly is attached to the sample blueprint and you are ready to start your takeof. 'ith your
mouse, click on points around an area and double-click to end the takeoff.
7/25/2019 take off4
6/10
$lick on the Estimate tab and the (ssembly details and all costs are automatically calculated. "otice
that the drawing is displayed in the lower right navigator window on the estimate sheet.
7.% &etting a &'a(e
The %et %cale feature allows you to select the measurement system and scale for the selected
drawing.To setup a scale, select the %et %cale option on the Takeoff menu tab. "ote that changing the scale
on an eisting takeoff will automatically recalculate all takeoff quantities.
&e(e't &)stem
This option allows you to pick between #mperial or )etric measurement systems.
&e(e't &'a(e
This option gives you a drop-down list of common architectural and engineering scales.
7/25/2019 take off4
7/10
"n#ut &'a(eThis option allows you to input a custom scale or your drawing.
*nits
This option displays the units of measure for the takeoff.
A##() to a(( Drawings
The default action applies all values to the selected takeoff drawing only. $heck this option to set
this scale for all drawings.
7.7 &etting a +ustom &'a(e
The %et $ustom %cale feature allows you to set a scale based on a known length on the plans.
To setup a custom scale, select the %et $ustom %cale option on the Takeoff menu tab. The system
will prompt you to select two points of a known length. (fter the second point is selected, the system
will prompt you to enter in the value for this length.
&e(e't &)stem
This option allows you to pick between #mperial or )etric measurement systems.
"n#ut ,ine ,ength
This option allows you to input the length for the selected line.
+ustom &'a(e
This option displays the actual line length.
*nits
This option displays the unit of measure for the takeoffs.
A##() to a(( Drawings
The default action applies all values to the selected takeoff drawing only. $heck this option to set
this scale for all drawings.
7.- "nserting Tet on a ,a)er
To quickly insert tet on a layer, select the #nsert Tet icon from the Takeoff menu tab, then drag and
7/25/2019 take off4
8/10
drop the icon where you would like the tet label to be placed.
(fter you drop the icon on the takeoff pane, the system allows you to type into an edit bo and
enter notes that you would like assigned to the selected layer.
-. DO+*/ENT&
-.1 About the Do'uments Page
The &ocuments tab maintains all drawings that have been imported into the estimate. These
drawings can be imported from a local hard drive, compact disk or through the i%q*t plan room. The
screen is divided into the navigation pane on the left and the document pane on the right that
displays the drawings.
Navigation Pane
On the left side of the screen is the navigation pane. The navigation pane gives you quick access to
all of the drawings in an estimate. The bottom status bar displays the specifications for the selecteddrawing file.
Do'ument Pane
The document pane on the right displays the selected drawing.
-.2 Navigation Pane
The navigation pane for the document tab lists all drawings that have been imported into an
estimate. There is no limit to the number of drawings that can be imported.
7/25/2019 take off4
9/10
0ight /ouse /enus
There are many functions available by using the right mouse menus on the navigation pane.
+o((a#se A((
This option will collapse the eplorer tree.
"m#ort Drawing
This option allows you to import a single or multiple drawing files at a time into the system.
De(ete Drawing
This option allows you to delete a single drawing file from the estimate.
A Drawing to TakeoffThis option allows you to add drawing files that were imported into the system to your takeoff tab. The system
allows you to import drawings for review without having them associated with a takeoff.
Down(oa Drawing
This option allows you to download selected drawing files from i%q*t pro+ects that have been imported.
-. Do'ument PaneThe document pane displays the selected drawing file.
8.4 iSqFt Projects
On the documents tab, the i%q*t icon allows you to import pro+ect files from the i%q*t site.
7/25/2019 take off4
10/10
$lick on the browse button to select an i%q*t pro+ect to import.