Takedown and Cleaning an AK47

8/4/2019 Takedown and Cleaning an AK47

1/28

Takedown and Cleaning an AK47

1. Remove the magazine and set it aside.2. Move the safety lever to "fire"3. Pull back the bolt carrier lever and eject any round from the chamber.4. While holding back bolt carrier lever, visually inspect the chamber to make sure it is empty.5. Push the bolt carrier forward.6. Press in the button on the rear of the receiver cover.7. lift the rear of the receiver cover, disengage the front of the receiver cover from the slot in the rear sighthousing. Pull the receiver cover free and set it aside.8. Notice that the button you pressed in step 6 is the rear of a rod with a long spring around it that goesinto the rear of the bolt carrier. Push the rear of that rod forward until it disengages from the rear of thereceiver.9. Lift the rod up and backward to remove it and its spring from the bolt carrier. Set the rod aside.10.Push the bolt carrier lever to the rear and lift the bolt carrier upward to remove it and the bolt from thereceiver.11.Remove the bolt from the bolt carrier by moving the bolt forward and rotating it until comes free fromthe bolt carrier. Set the bolt and bolt carrier aside.12.With a punch or your hand, rotate the lever on the right side of the r ear sight upward about 90degrees.13.Remove the gas tube and hand guard by lifting the the rear of the tube and disengaging the front ofthe tube from the barrel attachment it slides into. Set the gas tube aside.

Assembly is the reversal of disassembly

How to take apart the AK47 recoil spring - Click Here

Gun Cleaning Kits 308, 30-06, 7.62 - Package of 3 Kits

Package of three universal military cleaning kits which include a weather proofpouch, small oil bottle, bore brushes for .30 and .45 caliber and small brushes forchamber and tight corners. Works for .308, .30-06, 7.62x39 and other .30 caliberrifles and handguns. Punch and drawstring all fit in a neat metal tobacco can foreasy carrying. Original German surplus item came as standard issue with AK typerifles.

1445399 10366853 CLN-120 http://w w w .che

Buy here to support our website

Easy right?OK Here's more help with pictures and video;NOTE - Pictures taken on a cut receiver which turned out to be too much disassembly,
http://www.ak-47.us/BreakDown.php#rehttp://www.ak-47.us/BreakDown.php#rehttp://www.ak-47.us/BreakDown.php#rehttp://www.ak-47.us/BreakDown.php#re


2/28

DO NOT CUT YOUR RECEIVER

Rear Stock is held on by two screws and TIGHT wood


3/28

On a real rifle use a rubber malletRest the trigger guard on a table edge (padded)

Pull down hard on the stockIf more force is needed I use a few taps

to the receiver area to help jar the wood free(Usually a folding stock will fit right in where the wood was if you get the correct type.)

Now up front move this lever up and back to release the top hand guard

Lever moved hand guard moving out


4/28

Now we are headed to where the arrow is pointing


5/28

Flip this lever up and over to release the metal part that will slide fore ward on the barrel(I wish I would have taken the cleaning rod out before I took the pic, act like you don't see it)

Now replacing the top hand guard wood is easy as heck but tough to explain so here's the explanationthen watch the movie to see it done

Hold the metal part of the gas tube in your hand, then grab the wood also. like you would a sword or lightsaber. Now twist your hands like if you were going faster on a motorcycle. That twist will rotate the wood

on the tube and poof it's off. Now watch the video

How to Remove the Top Front Grip on the AK-47

Click Here to See the Movie

Have about this many parts left when it's disassembled
http://www.ak-47.us/vid/FrontGrip.wmvhttp://www.ak-47.us/vid/FrontGrip.wmvhttp://www.ak-47.us/vid/FrontGrip.wmv


6/28

Worry if you have this many parts after disassembly;


7/28

The assembled Recoil Spring assembly

How to take apart the AK47 recoil spring

This doesn't need to be done too often, maybe to add a recoil buffer (but many of them slide over thespring). But if you need to take apart the recoil spring, try this method.

First compress the spring down to the first 'link' or section of the center wire. Then you can bend thatcenter 'linked' wire support to basically trap the spring while it's compressed. Be aware this spring is now


8/28

under great pressure, so pay attention.

Next 'twist' off the end retaining 'nut' it basically falls right off with no spring tension. To remove the springcarefully let it un compress and it's apart.

To get it back together, reverse these stops. Push the spring down as far as possible until you can lock it

back. then using the wire 'link' like chopsticks grip both side of the hole though the end 'nut' as the springis let back SLOWLY (so it doesn't shoot the 'nut' across the room) it will put pressure back on the end 'nut'and the assembly is back together.

A picture is better and I think this one pretty much explains the steps. Keep in mind it rough to hold thiswith one hand and take a pic with the other. The nut is in the brown part of the cammo below, it looks likea nut with a hole drilled through it the wrong way. No fancy screws or threads it's just held in place withthe spring tension.

The spring compressed and 'locked' in place while the end 'nut' is removed

Here's a Book someone scanned and sent to us


9/28


10/28


11/28


12/28

Most of the AK47 rifles were made with completely machined receivers. The receiver of the AKM ismade from the stamped sheet steel, with machined steel inserts riveted into the place where required.The receiver cover is a stamped sheet metal part, with stamped strengthening ribs found on the AKMcovers.

The gas operated action has a massive bolt carrier with a permanently attached long stroke gas piston.The gas chamber is located above the barrel. The bolt carrier rides on the two rails, machined in thereceiver, with the significant clearances between the moving and stationary parts, which allows the gun tooperate even when its interior is severely fouled with sand or mud. The rotation of the bolt is ensured bythe curved cam track, machined in the bolt carrier, and by the appropriate stud on the bolt itself. Thereturn spring and a spring guide are located behind the gas piston and are partially hidden in its hollowrear part when bolt is in battery. The return spring base also serves as a receiver cover lock. The cockinghandle is permanently attached to the bolt carrier (in fact, it forms a single machined steel unit withcarrier), and does reciprocate when gun is fired.


13/28

Top of Page

General AK-47 Information
http://www.ak-47.us/BreakDown.php#tophttp://www.ak-47.us/BreakDown.php#top


14/28

Caliber 7.62x39 mmAction: Gas operated, rotating bolt with 2 lugs

Overall length: 870 mmBarrel length: 415 mm

Weight: 4,300 g with empty magazine, 4,876 g loadedMagazine capacity 30 rds (40 rds box magazines and 75 rds drums)

Sighting range, m: 800Cyclic rate of fire 600 rds/min

Practical rate of fire, single shots 90-100 rds/min; bursts 400 rds/minMuzzle velocity: 780 m/s

The following extract comes from US Army Field Manual 100-2-3 - The Soviet Army; TroopsOrganization and Equipment published in June 1991. The publication was approved for publicrelease with unlimited distribution (ie may be freely used). The entry provided covered the AK-47, AKS, AKM and the AKMS military assault rifles.

Our new AK47 version chart is being developed,

check it out, write a review of your favorite AK47 or AK74

Buying weapons today is cheap. In fact, for modern armies who buy large sums, most optical sights cost

much more then assault rifles per unit.

Description:The original AK was also known as the AK-47. It was a gas-operated, selective-fire

weapon. Like all 7.62-mm Kalashnikov assault rifles, it fired the Soviet 7.62 x 39-mm

M1943 round and used a standard 30-round curved box magazine. The AK came in

two versions: one with a fixed wooden stock, and another, the AKS, with a folding

metal stock issued primarily to parachutist and armor troops. Except for the

differences in the stock and the lack of a tool kit with the AKS, the two version were

identical. The early AKs had no bayonet, but the version with the fixed wooden stocklater mounted a detachable knife bayonet.

The improved model, known as theAKM, is easier to produce and operate. It

weighs about one kilogram less than the AK. The reduced weight results from using

thinner, stamped sheet metal parts rather than machined, forged steel; laminated wood

rather than solid wood in the hand guard, forearm, pistol grip, and buttstock; and new

lightweight aluminum and plastic magazines. Other improvements include a straighter

stock for better control; an improved gas cylinder; a rate-of-fire control alongside the

trigger; a rear sight graduated to 1,000 meters rather than 800 meters; and a greatly

improved, detachable bayonet.

TheAKMalso has a folding-stock version, designated AKMS, intended for use by

riflemen in armored infantry combat vehicles such as the BMP. Except for its T-

shaped, stamped-metal, folding buttstock, the AKMS is identical to theAKM. The

folding-stock model can reduce its length from 868 to 699 millimeters.

Some AK Variants

AKS-47Folding Stock

AKM-47

RPK

SVD

SAR-1

WASR-10

MAK-90

MAADI

AKS-74

GP-30

Galil (Israeli)

Polish Variants

Indian Variants
http://www.ak-47.us/gear/AK47_Review.phphttp://www.ak-47.us/gear/AK47_Review.phphttp://www.ak-47.us/gear/AK47_Review.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKS-47.phphttp://www.ak-47.us/AKS-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/RPK.phphttp://www.ak-47.us/RPK.phphttp://www.ak-47.us/SVD.phphttp://www.ak-47.us/SVD.phphttp://www.ak-47.us/SAR-1.phphttp://www.ak-47.us/SAR-1.phphttp://www.ak-47.us/WASR-10.phphttp://www.ak-47.us/WASR-10.phphttp://www.ak-47.us/MAK-90.phphttp://www.ak-47.us/MAK-90.phphttp://www.ak-47.us/MAADI.phphttp://www.ak-47.us/MAADI.phphttp://www.ak-47.us/AKS-74.phphttp://www.ak-47.us/AKS-74.phphttp://www.ak-47.us/GP-30.phphttp://www.ak-47.us/GP-30.phphttp://www.ak-47.us/Israel.phphttp://www.ak-47.us/Israel.phphttp://www.ak-47.us/Polish.phphttp://www.ak-47.us/Polish.phphttp://www.ak-47.us/India.phphttp://www.ak-47.us/India.phphttp://www.ak-47.us/India.phphttp://www.ak-47.us/Polish.phphttp://www.ak-47.us/Israel.phphttp://www.ak-47.us/GP-30.phphttp://www.ak-47.us/AKS-74.phphttp://www.ak-47.us/MAADI.phphttp://www.ak-47.us/MAK-90.phphttp://www.ak-47.us/WASR-10.phphttp://www.ak-47.us/SAR-1.phphttp://www.ak-47.us/SVD.phphttp://www.ak-47.us/RPK.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKS-47.phphttp://www.ak-47.us/AKS-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/gear/AK47_Review.phphttp://www.ak-47.us/gear/AK47_Review.phphttp://www.ak-47.us/gear/AK47_Review.php


15/28

Russian VEPR

The safety lever serves two functions when in the upper or "safe" position. First, it blocks dirt from entering

the action by covering the slot the bolt carrier lever moves through when the weapon is fired. This also preventsthe weapon from being cocked while on "safe".

Second, an extension on the pin holding the lever through the receiver blocks the rear of the trigger, preventing

the trigger from being pulled. When the safety lever is moved to "fire, the action may be cycled, and the trigger is

the only thing holding the hammer from falling.

When the trigger is pulled, the hammer falls, hits the rear of the firing pin, and the round detonates.Note that

the AK-47 bolt is locked closed by rotating when the bolt carrier is moved forward (there is a cam on the top of

the bolt that engages a slot in the bolt carrier to accomplish the rotation). The firing pin is free-floating -- there is

no spring to hold it retracted until the hammer falls. Consequently, if one manually cycles live rounds through the

AK-47, one will observe light indentations on the primers where the firing pit hit against them as the action closed.

Consequently, it is inadvisable to chamber live rounds unless you are prepared for the possibility of the weapon

firing when you do so.

Slam-fires do not seem to be as common as with the SKS, and it is hard to get enough dirt into the action tocause it to malfunction for that reason. I recall one report of flawless functioning even when the rifle was so

covered in mud as to be hardly recognizable as a firearm.

The action is gas-operated: when a round detonates, some gas from the explosion is vented out of a small hole

at the top of the barrel near the muzzle. This gas pushes against the front of the piston in the gas tube, which is

connected to the bolt carrier. As the bolt carrier is pushed rearward by the gas, the bolt rotates to unlock and

moves rearward, and the round in the chamber is extracted and pulled back.

The round is ejected when it hits against a small protrusion on the left side of the receiver as the bolt moves

rearward. Simultaneously, the back of the bolt pushes the hammer back and cocks it.

The hammer is held back by the disconnect or (the trigger is almost certainly still pulled, since the actioncycles much faster than the operator can release the trigger). The bolt and bolt carrier recoil against the recoil

spring and guide rod, and come back forward. As the bolt comes forward, it grabs the top round from the

magazine and puts it in the chamber.

There is no feature to hold the bolt open after the last round is fired from the magazine. When the operator

releases the trigger, the disconnect or moves rearward and releases the hammer to move about 1/8", at whichpoint it is stopped by the (now released) trigger until the operator pulls the trigger a second time.

In 1990 the Army was equipped with the modernized Kalashnikov submachine gun AK-74M, havingfolding plastic butt with the accessory placed in it and a plate for mounting optical and night sights.

In 1991 the same modernization was carried out with a light machine gun. And so the modernizedKalashnikov light machine guns RPK-74M (5.45 mm) was addopted in armament. It replaced fourmodification of light machine guns.

Nowadays Kalashnikov submachine guns, the series 100, are developed with the purpose ofexpansion of their nomenclature for various types of cartridges and export.
http://www.ak-47.us/VEPR.phphttp://www.ak-47.us/VEPR.phphttp://www.ak-47.us/VEPR.php


16/28

AK101 - the 5,56 mm Kalashnikov submachine gun for cartridge 5,56x45 NATOAK102 - the same but with a short barrelAK103 - the 7,62 mm Kalashnikov submachine gun for cartridge 7,62x39AK104 - the same but with a short barrelAK105 - 5,45 mm Kalashnikov submachine gun with a short barrel for cartridge 5,45x39.

In 1993 within the framework of conversion of a defensive industry of "IZHMASH" Open Joint StockCompany developed the self-loading hunting carbine "Saiga" on the basis of the Kalashnikovsubmachine guns.

Our new AK47 version chart is being developed,

check it out, write a review of your favorite AK47 or AK74

Post your AK-47 pictures to our websites

Takedown and Cleaning an AK47

AK47-MP3 Jukebox

AK47 Toys

AK-47 Boker Automatic Knives

AK47 Manufacturers Markings

AK-47 Parts

Russian Military Patches

Capabilities:All 7.62-mm Kalashnikov assault rifles fire in either semiautomatic or automatic mode

and have an effective range of about 300 meters. At full cyclic rate, they can fire about600 rounds per minute (up to 640 rounds per minute for theAKM), with a practical rate of

about 100 rounds per minute fully automatic or 40 rounds per minute semiautomatic. Boththe AK and AKM can mount a grenade launcher. Both can have passive image intensifier

night sights. Both can function normally after total immersion in mud and water. The fullychromed barrel ensures effective operation even at very low temperatures. The muzzle of

either weapon fits into the swiveling firing points of the BMP. Thus, the infantryman canfire the weapon while the vehicle is moving.

Limitations:The most serious drawback to the AK andAKMis the low muzzle velocity (710 metersper second) of the relatively heavy 7.62-mm round. This results in a looping trajectory

that requires a clumsy adjustment for accuracy at ranges beyond 300 meters. The barrel

overheats quickly when the weapon fires for extended periods, making the weapon hard tohandle and occasionally causing a round to explode prematurely in the chamber. Theexposed gas cylinder is easily dented, sometimes causing the weapon to malfunction.
http://www.ak-47.us/gear/AK47_Review.phphttp://www.ak-47.us/gear/AK47_Review.phphttp://www.ak-47.us/gear/AK47_Review.phphttp://www.ak-47.us/Add_Your_Image.phphttp://www.ak-47.us/Add_Your_Image.phphttp://www.ak-47.us/BreakDown.phphttp://www.ak-47.us/BreakDown.phphttp://www.ak-47.us/MP3player.phphttp://www.ak-47.us/MP3player.phphttp://www.ak-47.us/AK47_Toys.phphttp://www.ak-47.us/AK47_Toys.phphttp://www.ak-47.us/AK-74Boker.phphttp://www.ak-47.us/AK-74Boker.phphttp://www.ak-47.us/AK47_Markings.phphttp://www.ak-47.us/AK47_Markings.phphttp://www.ak-47.us/AK47_Parts.phphttp://www.ak-47.us/AK-Patches.phphttp://www.ak-47.us/AK-Patches.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AK-Patches.phphttp://www.ak-47.us/AK47_Parts.phphttp://www.ak-47.us/AK47_Markings.phphttp://www.ak-47.us/AK-74Boker.phphttp://www.ak-47.us/AK47_Toys.phphttp://www.ak-47.us/MP3player.phphttp://www.ak-47.us/BreakDown.phphttp://www.ak-47.us/Add_Your_Image.phphttp://www.ak-47.us/gear/AK47_Review.phphttp://www.ak-47.us/gear/AK47_Review.phphttp://www.ak-47.us/gear/AK47_Review.php


17/28

Remarks:Although they designed it in 1947 and thus referred to it as the AK-47, the Soviets

actually adopted the AK in 1949. The AK entered service in 1951. It was the basicindividual infantry weapon of the Soviet Army until the introduction of the AKM. TheSoviets developed theAKMin 1959. It entered service in 1961. All 7.62-mm Kalashnikov

assault rifles are very dependable weapons. They produce a high volume of fire and aresimple to maintain. However, the new 5.45-mm assault rife AK-74 is replacing the 7.62-mm weapons.

Kalashnikov goal was to design a cheaply manufactured, automatic weapon that fired the new

Soviet 7.62x39mm intermediate power round. This round was intended to be a compromise between

the pistols rounds fired from submachine gun, which were controllable but lacked power, and the rifle

cartridges fired from heavier machine guns, which were either too heavy to fire while on themove or,if lightened, uncontrollable during automatic fire. The conventional wisdom is that the Nazi's

originated the concept of an assault rifle with their MP44 machine-pistol design, (which fired the

7.92x33 "8mm Kurz" round) and the Soviets copied them, but this is disputed by Ezell -- both sides

may have developed such weapons concurrently. Furthermore, Kalashnikov was hardly the only

_Soviet_ designer working toward this end at this time. Other designers looking at the 7.62x39

cartridge included Simonov (designer of the SKS) and Tokarev (designer of the weapons that bear hisname).

The following data comes fromJames Infantry Weapons 1995 - 1996.

Cartridge: 7.62 x 39 mm Operation: gas, selective fire

Locking: rotating bolt Feed: 30-round detachable box magazineWeight: 4.3 kg Length: 869 mm

Barrel: 414 mm Rifling: 4 grooves, rh, 1 turn in 235 mm

Sights: fore, post, adjustable; rear, U-notch, tangent Muzzle velocity: 710 m/sRate of fire: cyclic, 600 rds/min Effective range: 300 m

Links:Jane's Information Group - provides the Jane's series of military reference books.

Official Kalashnikov home page - provides comprehensive information on Kalashnikov

arms.Military Parade - the latest information from the Russian defense industry.

Sources:Headquarters, Department of the Army. FM 100-2-3 - The Soviet Army: Troops,Organization and Equipment. Washington D.C.: Department of the Army, June 1991.

Nedelin, A. Kalashnikov Arms. Moscow: Military Parade, 1997.Jane's Information Group Limited (edited by Gander, T. J. and Hogg, I. V.). Jane's Infantry

Weapons: 1995-96. London: Biddles, 1995. ISBN: 0 7106 1241 9.

Disassembly Guide - Click Here

Automat Kalashnikova, Model 1947 (AK47)
http://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/AKM-47.phphttp://www.ak-47.us/BreakDown.phphttp://www.ak-47.us/BreakDown.phphttp://www.ak-47.us/BreakDown.phphttp://www.ak-47.us/AKM-47.php


18/28

The AK47 is the worlds first widely used and sucessful assault rifle. AK stands for AvtomatKalashnikova, or in english "Kalashnikov automatic rifle". Kalashnikov is the name of the designer. TheAK, is the most prolific small arm of the 20th century. The total number of the AK-type rifles madeworldwide during the last 50 years is estimated to be over 90 million.

It has been and still is manufactured in dozens of countries with little modification to the original

design. The AK has been used in hundreds of countries and conflicts since its introduction. This is atrue legendary weapon, known for its extreme ruggedness, simplicity of operation and maintenance,and unsurpassed reliability even in worst conditions possible.

Caliber 7.62x39 mmAction: Gas operated, rotating bolt with 2 lugsOverall length: 870 mmBarrel length: 415 mmWeight: 4,300 g with empty magazine, 4,876 g loadedMagazine capacity 30 rds (40 rds box magazines and 75 rds drums)Sighting range, m: 800Cyclic rate of fire 600 rds/minPractical rate of fire, single shots 90-100 rds/min; bursts 400 rds/minMuzzle velocity: 780 m/s

1978-88 Oldsmobile Cutlass Calaisesoptioned with the Buick 231 V6will have the AK47 code as part of the Vehicle Identification Number

Code A represents the Buick 231, and the "K" code represents the Cutlass Calais line.

Code 47 refers to the bodystyle - a 2 door coupe.

AK-47 stands for "Avtomat Kalashnikova, model of 1947". AK-47 was designed byM.T.Kalashnikov in the 2nd half of the 1940s, and was adopted by Soviet Army in 1947 as

AK. It was manufactured in huge numbers, for both internal use and export. Many

countries, such as Romania, Bulgaria, East Germany, PR China and others alsomanufactured clones of the AK. Main production facility of the AKs was IzhMash - Izhevsk

machine building Plant, Izhevsk, Russia.Technically, AK is select-fire, gas-powered, magazine fed assault rifle. Gas system of

the AK uses long stroke gas piston, attached to bolt carrier. AK features rotating bolt withtwo massive lugs that locks securely into slots, cut in the inner walls of the receiver. The

receiver itself was machined from the solid steel bar, receiver cover was stamped from

sheet metal. Barrel is attached into receiver permanently, and bore and the chamber arechrome lined.

AK is hammer-fired, select-fire weapon. The fire selector/safety switch is located at theright side of the receiver, and has three positions: "Safe" (upper position), "Auto"

(middle), "Single shots" (lower position). The safety switch is somewhat uncomfortable to

operate.AK features open iron sights, with front sight adjustable for windage and rear sight

adjustable for elevation and marked in 100s of meters, from 100 to 800 meters. Sightradius is too short, when compared to other assault rifles, such as M16.

The stock and grip are made of wood. Shortened variant of original AK, called AKS, was

intended for paratroopers and featured folding down metal buttstock.Original AK was improved in 1959. Original milled receiver was replaced by stamped

one, new receiver cover with stamped grooves for greater strength replaced the old plain

one, barrel was equipped with screwed-on muzzle flip compensator, that could be


19/28

replaced by silencer. Special subsonic ammunition with heavier (12 grams) bullet was

developed to be used with the silencer. This modified gun was adopted as AKM, andserved as a general issue small arm for the Soviet Army until 1974, when small-bore

variant of the AKM, AK-74, was adopted. But until now, many AKMs are still in limitedservice in Russian Army.

Legendary reliability of the AK comes from simple design and overpowered gas drive.

When operating in normal condition, the bolt carrier/bolt group moves at high speed andstrikes hard against the rear wall of the receiver and against the front wall of the receiver

on the way back to close the breech. This somewhat decreases the full-auto fire accuracy,but gives to the system the power needed to operate with seriously fouled and dirty

receiver.Thus, usually, AK require less cleaning under the battle conditions, and less sensitive to

powder quality, than other assault rifles, especially ones such as M16, designed with

relatively light bolt carrier/bolt groups and direct gas actions without gas pistons.In general, AKs are extremely rugged and reliable guns, simple to operate and field

strip, without any small parts that may be lost in field conditions. They are of average

accuracy and not too comfortable to carry and fire, but they do the job they designed to,

and do it excellent.AK is most copied assault rifle in the world. Leaving aside many ex-East-block

countries, officially licensed clone of the AK is still manufactured in Finland, as

Sako/Valmet. An improved copy of the Valmet is built in Israel as Galil, and the copy ofGalil is built in the South Africa as R-4 and R-5. Many other assault rifles, such as FN FNC,

bear the marks of the AK design.

AK47, named after its designer Mikhail T. Kalashnikov, was developed during the WWII,and in 1947 the production started on the Izhmash plant in the city of Izhevsk, one of the

most important Soviet military production centers (this plant, in order to hide its militarynature, was also producing motorcycles "Izh", used by Soviet teams in internationalcompetitions, and world-famous sporting and hunting rifles). M.T. Kalashnikov still lives in

Izhevsk and is among the most honored citizens of the city.

The first AK47s had a receiver that was part machined steel and part stampings with

rivets holding everything together. This design proved to be less than robust in the fieldand was modified several times to gradually create a much tougher firearm.

In 1959 a tough, well-thought-out model of the gun was introduced which again usedsteel stampings which were riveted together. This proved to be a superior design and isthe key variant seen in all modern versions of this rifle manufactured in Russia, as well as

China, Finland, and most of the former Eastern Block countries. This model was

designated the AKM (Avtomat Kalashnikova Modernizirovannyi) though many times it, too,is referred to as an "AK47" (as are the semi auto versions of the gun exported into the

US).

The AK47 and AKM are usually chambered for the M43 7.62x39mm cartridge which

originally developed for the SKS carbine.

If kept clean, the AK47 and its variants are very reliable and many of the variants are

blessed with a chromed bore (since most communist or formerly communist countries untilrecently used corrosive ammunition) which aids in cleaning and extends barrel life. Most


20/28

AK47s with quality ammunition are quite accurate - if the sights on these guns can beovercome.

On the down side, the AKs are heavy and the basic AK design is flawed from a "humanengineering" standpoint in several ways:

the rear sight has been placed forward so that the rifle has a very short sighting

radius (with the rear sight being a rather crude open "V" tangent sight);

there is no bolt hold-open device;

the safety/selector is located rather inconveniently on the right side of the rifle and

makes a distinctive "clack" when moved (which has lead to the death of many awould-be ambusher from Vietnam to South Africa).

During the so-called "drug war" of the 1980s, even semi auto versions of the AK47

were banned from import into the US since the guns were often used by criminals -though only in fictional TV shows for the most part.

Often heavier semi auto"RPK" and/or sniper versions of these rifles are also seen. Thesehave the longer barrels designed for military use on SAW (Squad automatic weapons -

light machine guns) or sniper rifles. Generally these guns do offer a little extra velocity tobullets leaving their barrels along with less report and muzzle flash. But the weight of

these guns (over 9 pounds when the guns are empty) makes them unsuitable for mostshooter's needs.

The AK-style rifles aren't pretty nor is their safety easy to operate. But the guns arerobust and magazines, parts, and accessories inexpensive making them a good choice forthose wanting a hunting rifle that can also serve as a fighting weapon.

(For a more detailed look at the AK47 and its variants including the RPK and various machine gun versions and theGalil rifles as well as accessories for these firearms, see Duncan Long's book, AK47: The Complete Kalashnikov Family of

Assault Rifles)

Top of Page
http://www.ak-47.us/AK-47info.php#tophttp://www.ak-47.us/AK-47info.php#top


21/28

The assembled Recoil Spring assembly

How to take apart the AK47 recoil spring

This doesn't need to be done too often, maybe to add a recoil buffer (but many of them slide over thespring). But if you need to take apart the recoil spring, try this method.

First compress the spring down to the first 'link' or section of the center wire. Then you can bend thatcenter 'linked' wire support to basically trap the spring while it's compressed. Be aware this spring is nowunder great pressure, so pay attention.


22/28

Next 'twist' off the end retaining 'nut' it basically falls right off with no spring tension. To remove the springcarefully let it un compress and it's apart.

To get it back together, reverse these stops. Push the spring down as far as possible until you can lock itback. then using the wire 'link' like chopsticks grip both side of the hole though the end 'nut' as the springis let back SLOWLY (so it doesn't shoot the 'nut' across the room) it will put pressure back on the end 'nut'

and the assembly is back together.

A picture is better and I think this one pretty much explains the steps. Keep in mind it rough to hold thiswith one hand and take a pic with the other. The nut is in the brown part of the cammo below, it looks likea nut with a hole drilled through it the wrong way. No fancy screws or threads it's just held in place withthe spring tension.

The spring compressed and 'locked' in place while the end 'nut' is removed

Here's a Book someone scanned and sent to us


23/28


24/28


25/28

Most of the AK47 rifles were made with completely machined receivers. The receiver of the AKM ismade from the stamped sheet steel, with machined steel inserts riveted into the place where required.The receiver cover is a stamped sheet metal part, with stamped strengthening ribs found on the AKMcovers.

The gas operated action has a massive bolt carrier with a permanently attached long stroke gas piston.The gas chamber is located above the barrel. The bolt carrier rides on the two rails, machined in thereceiver, with the significant clearances between the moving and stationary parts, which allows the gun tooperate even when its interior is severely fouled with sand or mud. The rotation of the bolt is ensured bythe curved cam track, machined in the bolt carrier, and by the appropriate stud on the bolt itself. The

return spring and a spring guide are located behind the gas piston and are partially hidden in its hollowrear part when bolt is in battery. The return spring base also serves as a receiver cover lock. The cockinghandle is permanently attached to the bolt carrier (in fact, it forms a single machined steel unit withcarrier), and does reciprocate when gun is fired.


26/28

AK-47 Version List / Buyers Guide

Here you can research AK47 types then rate and review each item.

Let the rest of our visitors know your opinion

Choose the way you'd like to browse our AK47 database

AK-47 ComparisonOne Big Page

AK47 Thumbnail ListOne Med Page

View in List FormMany Smaller pages

Who Writes Our Reviews?

You Do, We review many different types of AK-47. In addition we encourage visitors to

voice their opinions on what models they like, which are good or not, we let you decide.The reviews on our websites have been submitted by our viewers our editors and oursponsors. Some reviews are positive and some are negative. If you dont agree with areview, feel free to submit your own.

Browse AK-47 Types, Rate and Review themMost recent reviews from visitors - Click Here

We have 332 AK47 types listed as of Tue Sep 13, 2011

Choose an AK Variant

Read Review

We post the reviews of your favorite AK47 rifles & AK47 pistols
http://www.ak-47.us/gear/AK47_Chart.phphttp://www.ak-47.us/gear/AK47_Chart.phphttp://www.ak-47.us/gear/AK47_Review_BB.phphttp://www.ak-47.us/gear/AK47_Review_BB.phphttp://www.ak-47.us/gear/AK47_ReviewList.phphttp://www.ak-47.us/gear/AK47_ReviewList.phphttp://www.ak-47.us/gear/Gear_Review_List.phphttp://www.ak-47.us/gear/Gear_Review_List.phphttp://www.ak47review.com/http://www.ak47review.com/http://www.ak-47.us/gear/AK47_ReviewList.phphttp://www.ak-47.us/gear/AK47_Review_BB.phphttp://www.ak-47.us/gear/AK47_ReviewList.phphttp://www.ak-47.us/gear/AK47_Review_BB.phphttp://www.ak-47.us/gear/AK47_ReviewList.phphttp://www.ak-47.us/gear/AK47_Review_BB.phphttp://www.ak-47.us/gear/AK47_ReviewList.phphttp://www.ak-47.us/gear/AK47_Review_BB.phphttp://www.ak47review.com/http://www.ak-47.us/gear/Gear_Review_List.phphttp://www.ak-47.us/gear/AK47_ReviewList.phphttp://www.ak-47.us/gear/AK47_Review_BB.phphttp://www.ak-47.us/gear/AK47_Chart.phphttp://www.ak-47.us/gear/AK47_ReviewList.phphttp://www.ak-47.us/gear/AK47_Chart.php


27/28

Also AK47 Receiver Reviews, AK47 Parts kit reviews, AK47 Bayonet reviews, and more

We upgraded our popular AK47 review system and put it on it's ownwebsite. Soon this website will share the new features, but for now enjoythe sorted lists on topics like: Top 10 AK47, AK47 Rifle Review, AK47Rifle Folder Review, US Built AK47 Review, AK47 Pistol Review, AK47Shotgun Review, AK47 Receiver Review, AK47 Receiver Flats, AK47

Parts Kit Review, AK47 Bayonet Review, AK47 US Parts Review

Top of Page
http://www.ak47review.com/http://www.ak47review.com/AK47_Top_10.phphttp://www.ak47review.com/AK47_Reviews_Rifle.phphttp://www.ak47review.com/AK47_Reviews_Rifle_Folder.phphttp://www.ak47review.com/AK47_Reviews_Rifle_Folder.phphttp://www.ak47review.com/AK47_Reviews_US_Made.phphttp://www.ak47review.com/AK47_Reviews_Pistol.phphttp://www.ak47review.com/AK47_Reviews_Shotgun.phphttp://www.ak47review.com/AK47_Reviews_Shotgun.phphttp://www.ak47review.com/AK47_Reviews_Receiver.phphttp://www.ak47review.com/AK47_Reviews_Parts_Kits.phphttp://www.ak47review.com/AK47_Reviews_Parts_Kits.phphttp://www.ak-47.us/gear/AK47_Review.php#tophttp://www.ak47review.com/http://www.ak47review.com/http://www.ak-47.us/gear/AK47_Review.php#tophttp://www.ak47review.com/AK47_Reviews_Parts_Kits.phphttp://www.ak47review.com/AK47_Reviews_Parts_Kits.phphttp://www.ak47review.com/AK47_Reviews_Receiver.phphttp://www.ak47review.com/AK47_Reviews_Shotgun.phphttp://www.ak47review.com/AK47_Reviews_Shotgun.phphttp://www.ak47review.com/AK47_Reviews_Pistol.phphttp://www.ak47review.com/AK47_Reviews_US_Made.phphttp://www.ak47review.com/AK47_Reviews_Rifle_Folder.phphttp://www.ak47review.com/AK47_Reviews_Rifle_Folder.phphttp://www.ak47review.com/AK47_Reviews_Rifle.phphttp://www.ak47review.com/AK47_Top_10.php


28/28

Documents

Takedown and Cleaning an AK47