Upload
hoangquynh
View
226
Download
0
Embed Size (px)
Citation preview
A catalogue of standard products manufactured at Humes Invermay. All products are cast with means of lifting unless otherwise specified. Other products can be manufactured to your specifications on request.
Standard products
Humes19 - 25 Churchill Park Drive
Invermay TAS 7248
Phone: 03 6335 6300 Fax: 03 6335 6330
Table of contents600mm dia. access chamber shaft and cover .............................................................. 1900mm dia. access chamber shaft and cover .............................................................. 2750mm surround and covers (1010 dia.) ......................................................................... 31050mm dia. access chamber shaft ............................................................................... 41350mm surround and cover ........................................................................................... 51430mm offset light duty surround and covers .............................................................. 61420mm offset heavy duty surround and class D cover ............................................... 71050 – 600mm conical top ................................................................................................ 8Junction pit frames and covers ........................................................................................ 91120mm square frame and cover ................................................................................. 10Side entry pit frame with circular cover ........................................................................ 11Side entry pit frame with rectangular cover .................................................................. 12Side entry pit frame (mountable kerb) - DMR type ..................................................... 13Side entry pit frame (mountable kerb) - DMR type ..................................................... 14Gully pit lintels and grates ............................................................................................... 15Half section spoon drain ................................................................................................. 16Gutter crossing ................................................................................................................. 17Mini headwall and subsoil endwall ................................................................................ 18Mountable Kerbs .............................................................................................................. 19Tapered channel (batter) ............................................................................................... 201200 litre Humepit (gray water pit) ................................................................................ 21Rural headwalls ................................................................................................................ 22Stormwater pits, risers and grates (900 x 600, 900 x 900) ............................................. 23Stormwater pits, risers and grates (300 x 300) ............................................................... 24Stormwater pits, risers and grates (400 x 400) ............................................................... 25Stormwater pits, risers and grates (500 x 500) ............................................................... 26Stormwater pits, risers and grates (600 x 600) ............................................................... 27Stormwater pit and risers (LCC type with sump 850 x 750) ......................................... 28
1
50
700
680
600
50
700
680
600
600mm dia. access chamber shaft and coverThis product is not manufactured with step iron holes or lifting lugs, so must be manouvered with chains/strap.
Sections join together with butt joints. As with all shafts, to achieve a water tight seal, mortar or similar will have to be applied to all joints. The 600 plain cover is suitable for stormwater applications and pedestrian traffic. For traffic and sewer applications refer page 3 (750 surround with light duty or heavy duty gatic cover).
Description Number Mass (t)
600mm shaft sections various 0.243/m
600mm plain concrete cover 5027055 0.055
ShaftShafts are centrifugally spun (not vertically cast) giving a very high strength reinforced concrete. These are available in 0.31, 0.61, 0.91 and 1.22 metre lengths. This allows smaller, more manageable sections to be stacked if handling is a problem.
Cover600mm plain concrete cover with built in rebate.
Fitted with 1no. recessed steel galvanised lifting handle.
Figure 1.1 – Cover cross section
Figure 1.2 – 600mm shaft
2
900mm dia. access chamber shaft and coverThe 900mm shaft is manufactured with 2 x 1.3t lifting lugs at the spigot end for handling and may be fitted with the 750 surround (refer page 3), or various covers for appropriate applications. Any section may be cast with a base except 0.31m length section. When a section is cast with a base the effective length of the section when installed is reduced by approx 40 - 60mm. Section joints are internal flush joints (FJ), therefore mortar or similar should be applied to joint gaps where a water tight seal is required.
Description Number Mass (t)
900mm shaft sections various 0.443/m
1300 x 100mm base various 0.336
ShaftShafts are centrifugally spun, not vertically cast, giving a very dense, high strength reinforced concrete. Available in lengths of 0.31, 0.61, 0.91, 1.22, 1.53, 1.83, 2.14 and 2.44 metres. The cost of a 0.91m section is about the same as the cost of 3 x 0.31m sections allowing smaller, more manageable sections to be joined if handling is an issue on site due to product mass.
CoverRefer to 750 surround and covers on page 3.
BaseShaft sections may be cast with a 1300 x 100mm base upon request. Please order bases in advance as 900mm dia. sections with a base are not stocked.
Figure 2.2 – 900mm shaft Figure 2.3 – Base cross section
915
1029
57
1300
100
915
1029
57
1300
100
Shaft keys in 40-60mm
3
750 surround and coversThis surround suits the 600 and 900mm access chamber shafts or the1050 conical top. It is suitable for pedestrian or non-traffic applications when fitted with banded concrete cover, light traffic when fitted with light duty gatic cover, highway loadings when fitted with heavy duty gatic cover. The gatic covers are gas tight therefore suitable for sewer applications.
Description Number Mass (t)
750 surround 5027065 0.129
710 banded “SW” cover 5027056 0.084
750 surround cast with LD gatic cover 5027066 0.181
750 surround cast with HD gatic cover 5027067 0.181
Hatched surface marked “SW”. Fitted with 2 no. recessed galvanised 1.3t lifting lugs
25 x 5mm galvanised steel band
Figure 3.1 – 710mm banded cover and 750 frame
Figure 3.2 – 710mm banded cover cross section Figure 3.4 – Gatic covers (concrete infill)
Figure 3.3 – 750 frame (1010mm dia.) cross section
1010
697
720
603
82150
1010
697
720
603
82150
Light duty
Heavy duty
4
1050mm dia. access chamber shaftThe 1050mm shaft is available in 0.305m increments and is manufactured with prefab step iron holes (at 375mm centres) and 1.3t lifting lugs at the spigot end. Various surrounds and covers can be fitted for appropriate applications. Any section may be cast with a base except 0.31m, however the effective length of the section when installed is reduced as the key in is 40-60mm into the base. Section joints are internal flush joints (FJ), therefore mortar or similar should be applied to joint gaps where a water tight seal is required.
Description Number Mass (t)
1050mm shaft sections various 0.443/m
1300 x 100mm base various 0.336
ShaftShafts are centrifugally spun, not vertically cast, giving a very dense, high strength reinforced concrete. Available in lengths of 0.31, 0.61, 0.91, 1.22, 1.53, 1.83, 2.14 and 2.44 metre lengths. The cost of a 0.91m section is about the same as the cost of 3 x 0.31m sections allowing smaller, more manageable sections to be joined if handling is an issue on site due to product mass.
CoverRefer to surrounds and covers on pages 5,6,7.
BaseShaft sections may be cast with a 1300 x 100mm base upon request. Please order bases in advance as 1050mm shaft sections with bases are stocked, but not always available in all lengths.
Figure 4.1 – 900mm shaft Figure 4.2 – 900mm base cross section
915
1029
57
1300
100
915
1029
57
1300
100
Shaft keys in 40-60mm
1194
1066
1300
100
64
5
1350mm surround and cover(flying saucer, devonport surround)
This frame is suitable to use for the 1050mm dia. access chamber shaft in non-traffic, stormwater applications. The frame design is only suitable for pedestrian type traffic and cannot be cast with gatic covers. Please refer to pages 6 and 7 for frames and covers suitable for sewer and traffic applications.
Description Number Mass (t)
1350mm surround 5027064 0.358
750mm banded “SW” cover 5027060 0.091
Hatched surface marked “SW”. Fitted with 2 no. recessed galvanised 1.3t lifting lugs
2 no. swiftlift
Figure 5.1 – 750mm banded cover and 1350mm frame
Figure 5.2 – 750mm banded cover cross section
Figure 5.3 – 1350mm frame cross section
25 x 5mm galvanised steel band
13601000
772
747
1372619610
102152
75
6
1430mm offset LD surround and covers(lilydale surround, light duty offset surround)
This frame is designed to suit a 1050mm access chamber shaft and can be cast with a light duty gatic frame and cover which is water and gas tight.
It is suitable for pedestrian areas with the banded concrete cover and light traffic or sewer applications when cast with the gatic cover. Both styles of covers branded “SW” are ex-stock, “S” branded covers are made on request. The total height of frame is 150mm with either type of cover.
Description Number Mass (t)
1430mm offset surround 5027070 0.403
750 banded “SW” cover 5027060 0.091
1430mm offset surround c/w LD gatic cover (Class B) 5027071 0.455
Hatched surface marked “SW”. Fitted with 2 no. recessed galvanised 1.3t lifting lugs
Figure 6.1 – 750mm banded cover and 1430mm offset frame
Figure 6.2 – 750mm banded cover cross section
Figure 6.4 – Light duty gatic cover (concrete infill)
2 no. swiftlift
25 x 5mm galvanised steel band
Figure 6.3 – 1430mm offset frame cross section
150
1390
1000765
745
620
615
1430
50 50
75150
1390
1000765
745
620
615
1430
50 50
75
7
1420mm offset HD surround and class D cover(highway surround, heavy duty offset surround)
This frame is to suit a 1050mm dia access chamber shaft. It is cast with a heavy duty Gatic frame and cover which is water and gas tight. Also suitable for heavy traffic and sewer applications. Covers are usually branded “SW” but can be branded with “S” if requested. The gatic cover extends the height of the surround to overall 250mm and sits up approximately 30mm proud of the concrete surround so that only the surface area of the gatic cover is exposed once pavement is completed.
Description Number Mass (t)
1430mm offset surround (w/o gatic cover)
5027068 0.545
1420mm offset surround c/w HD gatic frame and cover
(Class D)5027069 0.647
Figure 7.2 – Heavy duty gatic cover (concrete infill)
Figure 7.1 – 1420mm offset frame cross section
8
1050 - 600mm conical top(Taper top, Cone)
This unit fits on top of a 1050mm dia. access chamber shaft and reduces the top opening to 610mm ID. It can be fitted with a 750 surround (1010mm dia) cast with various covers (refer page 3). It is suitable for all loadings depending on the type of surround fitted.
Description Number Mass (t)
1050 x 600mm conical top 5027051 0.580
Figure 8.2 – 1050 x 600mm conical top cross section
Figure 8.1 – 1050 x 600mm conical top
750 surrounds and covers.Refer page 3
610
820
1064
1290
686
610
820
610
820
1064
1290
686
9
Junction pit frames and coversThis frame suits stormwater applications and the covers are branded “SW” only. Used in areas where a frame of these dimensions is required.
Description Number Mass (t)
1200 x 900 x 130mm frame 5027039 0.285
1200 x 1200 x 130mm frame 5027040 0.410
1500 x 1200 x 130mm frame 5027041 0.527
710mm banded “SW” cover 5027056 0.084
1200 x 900 x 130mm frame c/w LD gatic cover 5103319 0.350
1200 x 1200 x 150mm frame c/w HD gatic cover 5087576 0.427
Hatched surface marked “SW”. Fitted with 2 no. recessed galvanised 1.3t lifting lugs
25 x 5mm galvanised steel band
Figure 9.2 – 710mm banded cover cross section
Light duty
Figure 9.3 – Gatic covers (concrete infill)
Heavy duty
900 or 12001200 or 1500
130
Figure 9.1 – 710mm banded cover and junction pit frame
10
1120mm square frame and coverThis surround is used by Wynyard Council as a cover for 1050mm access chamber shafts. Covers are concrete only, therefore not suitable for vehicular traffic.
Description Number Mass (t)
1120 x 1120 x 150mm access chamber kerb
5027052 0.299
750 x 750 x 75mm cover with galvanised band 5027054 0.134
Figure 10.1 – 1120mm square frame Figure 10.2 – 750mm square cover cross section
Figure 10.3 – 1120mm square frame cross section
Fitted with 2 no.drop down steel galvanised handles
Galvanised steel band
762
75 (75)
765
1120
1115
775
150
605
616
75
765
1120
1115
775
150
605
616
75
11
603
922
82
720
697 130
603
922
82
720
697 130
Side entry pit frame with circular coverThis frame is used to cover side entry pits in a kerb and gutter situation. It is suitable for pedestrian loadings. Total thickness of frame and cover is 130mm.
Description Number Mass (t)
1200 x 900 x 130mm side entry pit frame
5027086 0.285
710mm banded “SW” cover 5027056 0.084
25 x 5mm galvanised steel band
Figure 11.2 – 710mm banded cover cross section
Figure 11.3 – Side entry pit cross section
Hatched surface marked “SW”. Fitted with 2 no. recessed galvanised 1.3t lifting lugs
9221220
130
Figure 11.1 – 710mm banded cover and side entry pit frame
12
Side entry pit frame with rectangular coverThis frame is to suit side entry pits in a kerb and gutter situation. It is suitable for pedestrian loadings only. Total height of unit is 102mm when cover is installed.
Description Number Mass (t)
915 x 915mm side entry pit frame - Type A 5027083 0.174
1060 x 915mm side entry pit frame - Type B 5027085 0.210
1220 x 915mm side entry pit frame - Type C 5027088 0.246
915 x 750mm side entry pit frame - Type A 5027082 0.132
1060 x 750mm side entry pit frame - Type B 5027084 0.159
1220 x 750mm side entry pit frame - Type C 5027087 0.190
50mm side entry pit cover (one per unit) 5027091 0.050
Figure 12.1 – Side entry pit with rectangular cover
Figure 12.2 – Side entry pit with rectangular cover cross section
Type Length (x)
A 918
B 1067
C 1220
13
Side entry pit frame (mountable kerb) – DMR typeThis product is designed as a heavy duty cover for side entry pits. It is suitable for median strip and highway applications.
Description Number Mass (t)
Side entry pit (DMR mountable kerb) c/w HD gatic frame and cover 5027090 0.610
Deflector unit - Left to right 5027092 0.063
Deflector unit - Right to left 5027093 0.063
Figure 13.2 – Deflector unit
Figure 13.3 – Heavy duty gatic cover
150 x 12 galvanised kerb lintel
Figure 13.1 – Side entry pit (DMR mountable kerb)
14
Figure 14.2 – Deflector unit
Figure 14.3 – Heavy duty gatic cover
Figure 14.1 – Side entry pit (DMR barrier kerb)
Side entry pit frame (barrier kerb) – DMR typeThis product is designed as a heavy duty cover for side entry pits. It is suitable for median strip and highway applications.
Description Number Mass (t)
Side entry pit (DMR barrier kerb) c/w HD gatic frame and cover 5027089 0.620
Deflector unit - Left to right 5027092 0.063
Deflector unit - Right to left 5027093 0.063
150 x 89 x 13L galvanised kerb lintel
15
Gully pit lintels and gratesThis is to suit footpath installation for side entry pits. Cast in as part of the kerb and gutter, the galvanised grates shown are installed in the gutter as a point of acces into the pit and the lintel is formed as part of the kerb. This type of installation is a standard for most councils and new subdivisions.
Description Number Mass (t)
1220mm side entry gully pit lintel 5027026 0.215
1830mm side entry gully pit lintel 5027392 0.315
1220mm lintel bar can stopper 5023392 -
1830mm lintel bar can stopper 5023393 -
Gully pit frame and grate - LCC type (half and half)
5033519 0.056
Gully pit frame and grate - Standard type 5101945 0.040
Figure 15.1 – Gully pit lintel
Figure 15.2 – Gully pit grate - LCC type
Figure 15.3 – Gully pit grate - Standard type
1.22 or 1.83m
1.22 or 1.83m
16
Half section spoon drainThis product is for drainage, most commonly for low volume run off next to paths, houses, garages etc.
Description Number Mass (t)
150mm half section spoon drain 5027029 0.027
225mm half section spoon drain 5027030 0.046
Figure 16.1 – Half section
Figure 16.2 – 150mm half section cross section Figure 16.3 – 2225mm half section cross section
17
Gutter crossingThis product is used to create driveway crossings. It’s shape is designed to suit standard kerb and gutter.
Description Number Mass (t)
900mm gutter crossing (shaped) 5027024 0.190
Figure 17.1 – 900mm gutter crossing
Figure 17.2 – 900mm gutter crossing cross section
900900
Shaped gutter crossing90mm thick
Road junction made good with asphalt
200 x 150mm precast concrete lintelStandard 600mm wide
concrete kerb and gutter
Gutter crossing to be bedded on 6mm grout
Shaped gutter crossing90mm thick
Road junction made good with asphalt
200 x 150mm precast concrete lintelStandard 600mm wide
concrete kerb and gutter
Gutter crossing to be bedded on 6mm grout
18
Mini headwall and subsoil endwallThe mini headwall is used for soil retention at the end of pipes as in a driveway crossing etc. It is suitable for a 300mm diameter concrete pipe.
The subsoil endwall is suitable for 100mm PVC pipe and is used in subsoil drainage applications.
Description Number Mass (t)
300mm mini headwall 5027073 0.112
100mm subsoil endwall 5027022 0.054
Figure 18.1 – 300mm mini headwall
Figure 18.2 – 100mm subsoil endwall
19
Mountable kerbsThese products are commonly used for traffic islands, traffic barriers and wheel stops.
Description Number Mass (t)
M3 mountable kerb (low profile) 5027044 0.046
225 mountable kerb x 760mm 5027042 0.052
225 mountable kerb x 1520mm 5027043 0.103
Figure 19.1 – DMR mountable kerb
Figure 19.2 – 225 mountable kerb
PLAN SECTION
PLAN SECTION
20
Tapered channel (batter)(batter drain, batter channel)
This product is used for drainage of moderate volumes of water on road cuttings, bridge aprons etc. Effective length per unit when joined is 560mm.
Description Number Mass (t)
Taper channel 5027021 0.050
Figure 20.1 – Tapered channel
255
460525
375
440
220
440
50
255 40255 4020
220
610
460
525
45o
21
1200 litre Humepit (gray water pit)The Humepit is designed to act as a gray water pit where a submersible pump is used in conjunction with a septic tank. It is supplied as a single unit, with the frame which sits flush to the outside epoxied to the shaft. Swiftlifts are cast in the unit for ease of lifting. The removable inner lid is concrete only and only suitable for pedestrian loadings, not vehicles or heavy equipment.
Description Number Mass (t)
1200 litre Humepit (complete) 5029456 1.394
Figure 21.1 – 1200 litre Humepit cross section
280190
1360 OD
70
80
520
INLET (Knockout)Dia. 125mm taper to inside 120mm
1219 ID
1335
OUTLETDia. 45mm taper to inside 40mm(at 90o to inlet)
80550
55570
600
55570
600
550
22
Rural headwallsThese headwalls are of smaller dimensions than the regular type which makes them suitable for rural situations or where less fill on pipes in driveway crossings. Designed to suit 300 and 375mm pipe.
Description Number Mass (t)
300mm rural headwall 5029483 0.256
375mm rural headwall 5025755 0.256
Figure 22.1 – 300mm rural headwall
23
Stormwater pits, risers and grates (900 x 600, 900 x 900)Pits manufactured to AS4198-1994. Base units have 150 and 300mm risers which can be added on until required height is reached. 600 and 900mm high units only are cast with bases. The walls are 85 - 90mm thick with 40mm thick knockouts.
Knockouts are supplied in base units only to take up to 375mm pipes.
Humes can supply with grates as shown or various concrete frames and covers for different types of applications. Top edges of pit bases and risers are rebated to take a grate which are supplied fully galvanised.
Description Number Mass (t)
900 x 600 x 150mm riser 5027554 0.128
900 x 600 x 300mm riser 5027943 0.269
900 x 600 x 600mm base unit 5027846 0.540
900 x 600 x 600mm base unit - bottomless 5097215 0.385
995 x 685mm galvanised grate 5068696 0.063
900 x 900 x 150mm riser 5025089 0.134
900 x 900 x 300mm riser 5025064 0.267
900 x 900 x 900mm base unit 5027551 0.930
965 x 965mm galvanised grate 5068695 0.094
Figure 23.1 – Stormwater pit
Base unit
300mm riser
150mm riser
24
Stormwater pits, risers and grates Type 1 (300 x 300)All pits supplied with galvanised grates or concrete lids and knockouts to all vertical faces at varying heights. Base units be manufactured without bottoms.
Description Number Mass (t)
300 x 300 x 440mm base - Type 1 5095780 0.100
350 x 350 x 40mm galvanised grate 5095776 0.010
Figure 24.1 – Stormwater pit - Type 1
25
Stormwater pits, risers and grates Type 2 (400 x 400)All pits supplied with galvanised grates or concrete lids and knockouts to all vertical faces at varying heights. Base units be manufactured without bottoms.
Description Number Mass (t)
400 x 400 x 590mm base - Type 2 5095781 0.150
450 x 450 x 40mm galvanised grate 5095777 0.015
400 x 400 x 590mm base with cast in angle and heavy duty grate 5108677 0.180
520 520
Figure 25.1 – Stormwater pit - Type 2
26
Stormwater pits, risers and grates Type 3 (500 x 500)All pits supplied with galvanised grates or concrete lids and knockouts to all vertical faces at varying heights. Base units be manufactured without bottoms.
Description Number Mass (t)
500 x 500 x 590mm base - Type 3 5095782 0.175
550 x 550 x 40mm galvanised grate 5095778 0.020
500 x 500 x 590mm base with cast in angle and heavy duty grate 5108510 0.250
Figure 26.1 – Stormwater pit - Type 3
620 620
27
Stormwater pits, risers and grates Type 4 (600 x 600)All pits supplied with galvanised grates or concrete lids and knockouts to all vertical faces at varying heights. Base units be manufactured without bottoms.
Description Number Mass (t)
600 x 600 x 735mm base - Type 4 5095783 0.300
600 x 600 x 300mm riser - Type 4 5096459 0.150
650 x 650 x 40mm galvanised grate 5095779 0.025
600 x 600 x 735mm base with cast in angle and heavy duty grate 5418511 0.375
730 730
Figure 27.1 – Stormwater pit - Type 4
28
Stormwater pit and risers (LCC type with pump 850 x 750)Pits are supplied with knockouts to 3 vertical faces as per LCC specifications. These can be manufactured without the base. Risers can be ordered up to 600mm in height. Used mainly in Launceston City Council area usually in conjunction with the gully pit lintel components on page 15.
Description Number Mass (t)
850 x 750 x 1220mm base - LCC type 5096100 1.045
850 x 750 x 600mm riser - LCC type 5103184 0.480
850 x 750 x 450mm riser - LCC type 5096937 0.400
850 x 750 x 300mm riser - LCC type 5098381 0.270
850 x 750 x 250mm riser - LCC type 5098382 0.220
850 x 750 x 200mm riser - LCC type 5098384 0.180
850 x 750 x 150mm riser - LCC type 5098385 0.130
Figure 26.1 – Stormwater pit - LCC type
This brochure supersedes all previous literature on this subject. As the specifications and details contained in this publication may change please check with Humes Customer Service for confirmation of current issue. © 2010 Holcim (Australia) Pty Ltd ABN 87 099 732 297
Humes is a registered trademark and a registered business name of Holcim (Australia) Pty Ltd.