Tech Data Security Vision Frames - AnemostatSecurity Sliding Door Panel ... HIGH SECURITY METAL VISION FRAME FOR SPECIAL GLASS OR DOOR THICKNESS ... 12 GA. (2.8mm) cold rolled steel

DETAIL DRAWING

INDEXFOR

SECURITYPRODUCTSVISIONFRAMES

MODEL DESCRIPTION DATE PRINTED PAGESG-10 . . . . . . . . . . . . . . . . . . . . . . . . . . High Security for Special Glass or Door Thickness . . . . January 2015 . . . . . . . . . . 1SG-12-SP . . . . . . . . . . . . . . . . . . . . . . Medium Security with Speak Port . . . . . . . . . . . . . . . . . . January 2015 . . . . . . . . . . 2SG-12-LCP . . . . . . . . . . . . . . . . . . . . . Security with Locking Cuff Port / Food Pass . . . . . . . . . January 2015 . . . . . . . . . . 3SG-10-SP . . . . . . . . . . . . . . . . . . . . . . High Security with Speak Port . . . . . . . . . . . . . . . . . . . . January 2015 . . . . . . . . . . 4SG-10-RSP . . . . . . . . . . . . . . . . . . . . . High Security with Removable Double Speak Port . . . . January 2015 . . . . . . . . . . 5SSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . Security Sliding Door Panel . . . . . . . . . . . . . . . . . . . . . . January 2015 . . . . . . . . . . 6SG-10-SSD . . . . . . . . . . . . . . . . . . . . . High Security with Sliding Door Panel . . . . . . . . . . . . . . January 2015 . . . . . . . . . . 7SG-10-SP-SSD . . . . . . . . . . . . . . . . . High Security with Speak Port and . . . . . . . . . . . . . . . . January 2015 . . . . . . . . . . 8

Security Sliding Door PanelLoPro™-SSD . . . . . . . . . . . . . . . . . . . Lo-Profile Vision Frame with . . . . . . . . . . . . . . . . . . . . . January 2015 . . . . . . . . . . 9

Security Sliding Door PanelBR-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . Bullet and Impact Resistant . . . . . . . . . . . . . . . . . . . . . . January 2015. . . . . . . . . . 10SG-12-LSC . . . . . . . . . . . . . . . . . . . . . Security with Operating Security Cover and Lock . . . . . January 2015 . . . . . . . . . . 11FGS-75-SC . . . . . . . . . . . . . . . . . . . . . With Operating Security Cover . . . . . . . . . . . . . . . . . . . . January 2015. . . . . . . . . . 12FGS-75-LSC. . . . . . . . . . . . . . . . . . . . With Operating Security Cover and Lock . . . . . . . . . . . . January 2015. . . . . . . . . . 13LoPro™-SC. . . . . . . . . . . . . . . . . . . . . Lo-Profile with Operating Security Cover . . . . . . . . . . . . January 2015. . . . . . . . . . 14LoPro™-GR . . . . . . . . . . . . . . . . . . . . Lo-Profile with Security Grille One Side . . . . . . . . . . . . . January 2015. . . . . . . . . . 15LoPro™-SC-GR. . . . . . . . . . . . . . . . . Lo-Profile with Security Grille One Side . . . . . . . . . . . . . January 2015. . . . . . . . . . 16

and Operating Security CoverSL-IS. . . . . . . . . . . . . . . . . . . . . . . . . . . With Security Grille for Standard/Special . . . . . . . . . . . . January 2015. . . . . . . . . . 17

Glass or Door ThicknessFGS-MS-FR . . . . . . . . . . . . . . . . . . . . Fire Rated, Impact and Security . . . . . . . . . . . . . . . . . . . January 2015. . . . . . . . . . 18FGS-MS . . . . . . . . . . . . . . . . . . . . . . . . Impact and Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . January 2015. . . . . . . . . . 19SL-FS-LSC . . . . . . . . . . . . . . . . . . . . . Ventilating with Stainless Steel Screen . . . . . . . . . . . . . January 2015. . . . . . . . . . 20

and Security Grille Two Sides Plus Locking Security CoverSL-FS . . . . . . . . . . . . . . . . . . . . . . . . . . Ventilating with Stainless Steel Screen . . . . . . . . . . . . . January 2015. . . . . . . . . . 21

and Security Grille Two SidesFasteners for Security Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . January 2015. . . . . . . . . . 22

JANUARY 2015SECURITY VISION FRAMES INDEX PAGE A

TECHNICAL DATAFROM

D o o r P r o d u c t s4958 Stout Dr. #119, San Antonio, TX 78219

PH: 210.662.6300 • FAX: 210.662.2828e-mail: [email protected] • website: www.anemostat.com

FASTENERS: Special Security Screw Fasteners, See Page 26, this section. Plated Finishes to match the lock, hinges and closer.

FINISH: Custom Baked Enamel Colors (as per sample chip supplied). MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized (Zinc Plated).

product must be Galvanized or Stainless Steel.NOTE: For Exterior use, High Humidity or Salt Air application,

DOOR THICKNESS: 1 3/4" (44mm) (std), or up to 2 1/4" (57mm) (specify).

INSTALLATION: By drilling 1/4" (6mm) holes thru the door, around the perimeter of the door cutout. Frame has countersunk mounting holes for #8x32 one way vandal proof security screw thru bolts with a blank head on one side for flush appearance and improved security.

FINISH: Grey Primer, Beige or Bronze Baked Enamel.

MATERIAL: 10 GA. (3.4mm) Cold Rolled Steel Frame on glass 3/16" (5mm) to 1" (25mm) thick.12 GA. (2.5mm) Cold Rolled Steel Frame on glass over 1" (25mm) to 1 9/16" (40mm) thick.

GLAZING: Thickness can range from over 3/16" (5mm) and up to 1 9/16" (40mm). Glazing space of 1/8" (3mm) over glass thickness is standard, allowing for glazing tape to be used on both sides of the glass. Glazing material should be fire and/or safety rated with U.L. and/or W.H.I. classification markings.

USES: For use with glass 3/16" (5mm) and up to 1 9/16" (40mm) thick and high security is required.

SPECIALS: Fractional sizes, Glass thickness 3/16" (5mm) and up to 1 9/16" (40mm)and Door thickness up to 2 1/4" (57mm).

GLAZINGSPACE

1/8" (3mm)OVER GLASSTHICKNESS

FRAMEO.D.

INSIDE OUTSIDE

your area, to determine appropriate standards.Consult with the local authority having jurisdiction in

IMPORTANT: Interpretation of building and fire codes may vary.

ORDERSIZE

&DOOR

CUTOUT

VISIBLELITE

Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.

GLAZINGMATERIAL

ONE WAY VANDAL PROOF SCREWS

3/8"(10mm)

ORDE

R SI

ZE M

INUS

1/4

"(6

mm

)

ORDE

R SI

ZE P

LUS

1 1/

2"(3

8mm

)

1 3/4"(44mm)

OR SPECIFY

ORDE

R SI

ZEM

INUS

2 1

/2"

(64m

m)

2"(51mm)

MUST SPECIFYGLAZING MATERIAL

THICKNESS

DETAIL DRAWING

TECHNICAL DATAFROM

SG-10HIGH SECURITY

METAL VISION FRAME FOR SPECIALGLASS OR DOOR THICKNESS

STANDARD PRODUCT FEATURES OPTIONAL FEATURES

FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure

JANUARY 2015SECURITY VISION FRAMES PAGE 1

UNDERWRITERS’LABORATORIES

WARNOCK HERSEY

FIRERATINGS

Job Name & Location Submitted by

For Most Current Info, Consult Factory or check our website, www.anemostat .com



■ 20/45/60* MINUTE: Approved listing at 1296 sq. in. visible lite.(max. width 54", max. height 54").

■ 60**/90** MINUTE: Approved listing at 1080 sq. in. visible lite.(max. width 35", max. height 35").

■ 60/90 MINUTE: Approved listing at 100 sq. in. visible lite.(max. width 10", max. height 33").

*Must be used with FIRELITE Plus or NT and Fire listed glazing tape oranother manufacturer’s equivalent product. Glazing combination mustbe used in appropriately tested door assembly.**Must be used with 7/8" (23mm) or 1-1/16" (27mm) Pyrostop and fire listedglazing tape, and be used in an appropriately tested door assembly.

MEETS ASTM F-1450-97 †

IMPACT RATINGS† Tested in Compliance with ASTM F-1450-97 Must use 1/4” x 20 Thru Bolt blankone side (not shown in drawing, see page 26 this section).

B.S.-476.22 British Standard

Timber Doors - 30 min. and 1 hour.Steel Doors - 2 hours (4 hours actual).

BS 476.22British Standard


For Most Current Info, Consult Factory or check our website, www.anemostat .comJANUARY 2015

SECURITY VISION FRAMES PAGE 2

SG-12-SP is not fire rated

MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized(Hot Dipped, or Zinc Plated).

FINISH: Custom Baked Enamel Colors (as per sample chip supplied). Plated Finishes to match the lock, hinges and closer.

FASTENERS: Special Security Screw Fasteners,See Page 26, this section. SPECIALS: Fractional Sizes, Glass thickness 3/16" (5mm) and up to 1 9/16" (40mm)

and Door thickness up to 2 1/4" (57mm).

MATERIAL: 12 GA. (2.5mm) Cold Rolled Steel Frame on glass

FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: By drilling 1/4" (6mm) holes thru the door, around the

perimeter of the door cutout. Frame has countersunk mounting holes for #8x32 one way vandal proof security screw thru bolts with a blank head on one side for flush appearance.

DOOR THICKNESS: For 1 3/4" (44mm) (std) or up to 2 1/4" (57mm) (specify). GLAZING: Thickness can range from over 3/16" (5mm) and up to

NOTE: For exterior use, High Humidity or Salt Air application, product

your area, to determine appropriate standards.Consult with the local authority having jurisdiction in

IMPORTANT: Interpretation of building and fire codes may vary.must be Galvanized or Stainless Steel.

3/16" (5mm) and up to 1 9/16" (40mm) thick.

1 9/16" (40mm). Glazing space of 1/8" (3mm) over glass thicknessis standard, allowing for glazing tape or compoundto be used on both sides of the glass.

SPEAK PORT: 12 GA. (2.8mm) cold rolled steel plate with perforatedface. 1/4" (6mm) diameter holes on 3/8" (10mm) staggered centers.

VISIBLELITE

HEIG

HT =

ORDE

R SIZE

MINU

S 6 3/

4" (17

1mm)

WIDT

H = O

RDER

SIZE

MINU

S 2 1/

4" (57

mm)

GLASSSIZE

WIDT

H = O

RDER

SIZE

HEIG

HT =

ORDE

R SIZE

MINU

S 4 3/

4" (12

1mm)

MINU

S 1" (2

5mm)

HEIG

HT =

VISIBL

E LITE

+ 6 1

/4" (1

59mm

)WI

DTH

= VISI

BLE L

ITE +

2 1/4"

(57m

m)

GLAZING SPACE(1/8" (3mm) OVER

GLASS THICKNESS)


METAL STOPS

12 GA. C.R.S.PERFORATED FACE1/4" (6mm) DIA. HOLESON 3/8" (10mm)

FRAMEO.D.

DOOR CUTOUT + 1 1/2" (38mm)

12 GA. C.R.S. FRAME

INSIDE OUTSIDE

2" (51mm)

THICKNESS

3/8" (10mm)

1"(25mm)

STAG. CTRS.

1" (25mm)

3" (76mm)

1" (25mm)

1 3/4"(44mm)

OR SPECIFY


12 GA. (2.5mm) C.R.S.

PERFORATED FACE

ORDER SIZE&

DOOR CUTOUT

DETAIL DRAWING

TECHNICAL DATAFROM


FIRE RATINGS



SG-12-SPSECURITY

VISION FRAMEWITH

SPEAK PORT

NOT FIRE RATED

IMPACT RATINGS


† Tested in Compliance with ASTM F-1450-97 Must use 1/4" x 20 Thru Bolt blankone side (not shown in drawing, see page 26 this section).




SG-12-LCP is not fire rated


FINISH: Special Order Baked Enamel Colors (as per sample chip supplied). Plated Finishes to match the lock, hinges and closer.

FASTENERS: Special Security Screw Fasteners,See Page 26, this section.

SPECIALS: Fractional Sizes, Glass thickness 3/16" (5mm) and up to 1 9/16" (40mm)and Door thickness up to 2 1/4" (57mm).

MATERIAL: 12 GA. (2.5mm) Cold Rolled Steel Frame on glass


DOOR THICKNESS: For 1 3/4" (44mm) (std) or up to 2 1/4" (57mm) (specify).

NOTE: For exterior use, High Humidity or Salt Air application, productyour area, to determine appropriate standards.Consult with the local authority having jurisdiction in


must be Galvanized or Stainless Steel.

3/16" (5mm) and up to 1 9/16" (40mm) thick.SECURITY COVER: 16 GA. (1.7mm) cold rolled steel plate with security

keyed lock. Hinged to swing down for food passor cuff port.


6" (152mm)

METAL STOPS16 GA. LOCK GUARD

12 GA.C.R.S. FRAME

INSIDE OUTSIDE

CONTINUOUS HINGE

SECURITYCAM LOCKWITH KEY

HEIG

HT =

ORDE

R SIZE

MINU

S 9 5/

8" (24

4mm)

WIDT

H = O

RDER

SIZE

MINU

S 2 5/

8" (67

mm)

WIDT

H = O

RDER

SIZE

HEIG

HT =

ORDE

R SIZE

MINU

S 7-7/

8" (22

2mm)

MINU

S 1/4"

(25m

m)

HEIG

HT =

VISIBL

E LITE

+ 6 1

/4" (1

59mm

)WI

DTH

= VISI

BLE L

ITE +

2 1/4"

(57m

m)

GLAZING SPACE1/8" (3mm) OVER

GLASS THICKNESS

FRAMEO.D.

DOOR CUTOUT + 1 1/2" (38mm)

3/8" (10mm)

1"(25mm)

1" (25mm)

1" (25mm)


THICKNESSVISIBLE

LITE

GLASSSIZE

ORDER SIZE&

DOOR CUTOUT

2" (51mm)

1 3/4"(44mm)

OR SPECIFY

12 GA. C.R.S.SECURITY COVER

SECURITYCAM LOCKWITH KEYOPERATING

SECURITY COVER

1/4"(6mm)

9/32"(7mm)

INSTALLATION: By drilling 1/4" (6mm) holes thru the door, around the perimeter of the door cutout. Frame has countersunk mounting holes for #8x32 one way vandal proof security screw thru bolts with a blank head on one side for flush appearance.

GLAZING: Thickness can range from over 3/16" (5mm) and up to 1 9/16" (40mm). Glazing space of 1/8" (3mm) over glass thickness is standard, allowing for glazing tape to be used on both sides of the glass.

DETAIL DRAWING

TECHNICAL DATAFROM

SG-12-LCPSECURITY

VISION FRAMEWITH

LOCKINGCUFF PORT / FOOD PASS


FIRE RATINGS

NOT FIRE RATED






SG-10-SP is not fire rated



FASTENERS: Special Security Screw Fasteners, See Page 26, this section. SPECIALS: Fractional Sizes, Glass thickness 3/16" (5mm) and up to

1 9/16" (40mm) and Door thickness up to 2 1/4" (57mm).

MATERIAL: 10 GA. (3.4mm) Cold Rolled Steel Frame face frame (inside)



DOOR THICKNESS: For 1 3/4" (44mm) (std) or up to 2 1/4" (57mm) (specify). GLAZING: Thickness can range from over 3/16" (5mm) and up to

1 9/16" (40mm). Glazing space of 1/8" (3mm) over glass thickness is standard, allowing for glazing tape to be used on both sides of the glass.

NOTE: For exterior use, High Humidity or Salt Air application, product your area, to determine appropriate standards.Consult with the local authority having jurisdiction in



12 GA. (2.5mm) Cold Rolled Steel Frame back frame (outside)SPEAK PORT: Two 10 GA. (3.4mm) cold rolled steel plates with perforated

faces. 5/32" (4mm) diameter holes on 7/32" (5.5mm) staggeredcenters, with 20 GA. (0.9mm) baffle to prevent the passingof contraband.


OUTSIDEINSIDE

10 GA. OR 12 GA.C.R.S. FRAME

WIDT

H = O

RDER

SIZE

MINU

S 1" (2

5mm)

HEIGHT

= OR

DER S

IZEMI

NUS 6

3/4"

(171m

m)

GLAZING SPACE

GLASS THICKNESS1/8" (3mm) OVER

2" (51mm)

3/8" (10mm)

DOOR CUTOUT + 1 1/2" (38mm)O.D.

FRAME

DRAINAGE HOLES10 GA. C.R.S.PERFORATED FACE5/32" (4mm) DIA. HOLES ON 7/32" (6mm)STAG. CTRS

1 3/4"(44mm)

OR SPECIFY

ORDER SIZE&

DOOR CUTOUT

VISIBLELITE

GLASSSIZE


THICKNESS

20 GA. BAFFLE TOPREVENT PASS THRU

3" (76mm)

WIDT

H = O

RDER

SIZE

MINU

S 2 1/

4" (57

mm)

HEIGHT

= OR

DER S

IZEMI

NUS 4

3/4"

(121m

m)

HEIGHT

= VIS

IBLE L

ITE +

6 1/4"

(159

mm)

WIDT

H = V

ISIBL

E LITE

+ 2 1

/4" (5

7mm)

10 GA. C.R.S.PERFORATED FACE

WITH 20 GA. BAFFLE TOPREVENT PASS THRU

TECHNICAL DATAFROM

DETAIL DRAWING

SG-10-SPHIGH SECURITYVISION FRAME

WITHDOUBLE SPEAK PORT

(WITH BAFFLE)


FIRE RATINGS

NOT FIRE RATEDD o o r P r o d u c t s

4958 Stout Dr. #119, San Antonio, TX 78219PH: 210.662.6300 • FAX: 210.662.2828

e-mail: [email protected] • website: www.anemostat.com

IMPACT RATINGS


† Tested in Compliance with ASTM F-1450-97 Must use 1/4” x 20 Thru Bolt blankone side (not shown in drawing, see page 26 this section).




&DOOR CUTOUT

ORDER SIZE

OUTSIDEINSIDE

10 GA. OR 12 GA.C.R.S. FRAME

LITEVISIBLE SIZE

GLASS

GLAZING SPACE

GLASS THICKNESS1/8" (3mm) OVER

GLAZING MATERIALMUST SPECIFY

THICKNESS

2" (51mm)

3/8" (10mm)

DOOR CUTOUT + 1 1/2" (38mm)O.D.

FRAME

10 GA. S.S.PERFORATED FACE5/32" (4mm) DIA.HOLES ON 7/32"STAG. CTRS

20 GA. BAFFLE TOPREVENT PASS THRU

SPEAKPORT MODULE

REMOVEABLESTAINLESS STEEL

staggered centers. Module removeable for cleaning.face. 5/32" (4mm) diameter holes on 7/32" (5.5mm)

SPEAK PORT: 10 GA. (3.4mm) stainless steel plate with perforated

GLAZING: Thickness can range from 3/16" (5mm) and up to 1 9/16" (40mm). Glazing space of 1/8" (3mm) over glass thicknessis standard, allowing for glazing tape to be used on both sides of the glass.

DOOR THICKNESS: For 1 3/4" (44mm) (std) or up to 2 1/4" (57mm) (specify).



IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.

NOTE: For exterior use, High Humidity or Salt Air application, product

1 9/16" (40mm) and Door thickness up to 2 1/4" (57mm).SPECIALS: Fractional Sizes, Glass thickness 3/16" (5mm) and up to

FASTENERS: Special Security Screw Fasteners,Plated Finishes to match the lock, hinges and closer.

FINISH: Custom Baked Enamel Colors (as per sample chip supplied).

See Page 26, this section.

(Hot Dipped, or Zinc Plated).

SG-10-RSP is not fire rated

MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized

SECURITY SCREWS#8-32 TORX FLAT HEAD SOCKET

20 GA. stainless baffle prevents pass throughof contraband.

WIDT

H = O

RDER

SIZE

MINU

S 1" (2

5mm)

HEIG

HT =

ORDE

R SIZE

MINU

S 6 1/

4" (17

1mm)

1 3/4"(44mm)

OR SPECIFY

3" (76mm)


MATERIAL: 10 GA. (3.4mm) Cold Rolled Steel Frame face frame (inside)12 GA. (2.5mm) Cold Rolled Steel Frame back frame (outside)

WIDT

H = O

RDER

SIZE

MINU

S 2 1/

4" (57

mm)

HEIG

HT =

ORDE

R SIZE

MINU

S 4 3/

4" (12

1mm)

HEIG

HT =

VISIBL

E LITE

+ 6 1

/4" (1

59mm

)WI

DTH

= VISI

BLE L

ITE +

2 1/4"

(57m

m)

SPEAKPORT MODULE

REMOVEABLESTAINLESS STEEL

INSTALLATION: By drilling 1/4" (6mm) holes thru the door, around the perimeter of the door cutout. Frame has countersunk mounting holes for #8x32 one way vandal proof security screw thru bolts with a blank head on one side for flush appearance. Module is secured with #8-32 Torx security screws.

DETAIL DRAWING

TECHNICAL DATAFROM

SG-10-RSPHIGH SECURITYVISION FRAME

WITHREMOVABLE DOUBLE

SPEAK PORT


FIRE RATINGS

NOT FIRE RATED



FASTENERS: Special Security Screw Fasteners, See page 27, this section. SPECIALS: Fractional sizes and other steel gauges (contact factory).

MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized

FINISH: Custom Baked Enamel Colors (as per sample chip supplied).

USES: To provide selective vision into security areas.

lite kit (refer to dimensional data).(see tech. data sheet) or retrofit with existing vision Use with Anemostat SG-10 security vision frame or LoPro™

INSTALLATION: #8X3/4" one way vandal proof security screws.

MATERIAL: 12 GA. (2.5mm) Cold Rolled Steel Channel Frame and Sliding Door.


DOOR THICKNESS: Works on Doors 3/4" (19mm) and greater.

NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.

(Zinc Plated).


60/90 MINUTE: Approved listing at 100 sq.in. (0.065 m2) visible litemax. width 10" (254mm), max. height 33" (838mm).

max. width 36" (914mm), max. height 36" (914mm).20/45 MINUTE: Approved listing at 1296 sq.in. (0.836 m2) visible lite

NOTE: Door slides from side to side. Non-centered vision frame cutout is generally required, i.e. 12" x 12" LoPro vision frame requires 26" x 13" SSD with vision frame set to one side of door, not centered.

1 5/8" (41 mm)

ORDE

R SIZE

PLUS

3 1/4

" (83 m

m)

#8 COUNTERSUNK MOUNTING HOLES

12 GA.MOUNTING

FRAME#8X3/4"ONE WAYVANDAL PROOF

INSIDEOUTSIDE

SECURITY SCREW31/32" (25 mm)

VISIONFRAME O.D.

ORDER SIZEIS

INSIDE DIMENSIONOF

SLIDING DOOR TRACK

FORMEDPULL

HANDLE

FRAMEO.D.ORDER

SIZE

12 GA.SLIDER DOOR

O.D. WIDTH OF VISION FRAME x 2


PULLHANDLE

NOTE: When used with vision frame other than LoPro, or SG-10 outside dimensions of frame must be furnished.

ORDERSIZE

O.D. HEIGHT OF VISION

FRAME

IMPORTANT!VISION FRAME

CAN BE NO MORE THAN 1/8" OFF DOOR

DETAIL DRAWING

TECHNICAL DATAFROM

SSDSECURITY SLIDING DOORFOR SELECTIVE VISION

INTO HIGH SECURITY AREAS





WARNOCK HERSEY

FIRERATINGS




PH: 210.662.6300 • FAX: 210.662.2828e-mail: [email protected] • website: www.anemostat.com B.S.-476.22 British Standard



GLAZINGSPACE1/8" (3mm)OVER GLASSTHICKNESS

2"

ORDE

R SIZE

MINU

S 1/4"

(6mm

)

ORDE

R SIZE

PLUS

1 1/2

" (38m

m)

GLAZINGMATERIAL

FRAMEO.D.

ORDE

R SIZE

MINU

S 2 1/

2" (64

mm)

9/16" (14mm)1 5/8"

ORDE

R SIZE

PLUS

4 3/4

" (121

mm)

#8 x 3/4" ONE WAYVANDAL PROOF

SECURITY SCREW

VISIONFRAME

O.D.SSD

OUTSIDE INSIDE

(41mm) (10mm)3/8"

(51mm)

FORMEDPULL

HANDLE

Visible Lite

WidthDOOR CUTOUT

WIDTH

Visib

le Lit

e He

ight

DOOR

CUT

OUT

HEIG

HT


ORDERSIZE

&DOOR

CUTOUT

VISIBLELITEMUST SPECIFYGLAZING MATERIAL

THICKNESS

1 3/4"(44mm)

OR SPECIFY

GLAZING: Thickness can range from 3/16" (5mm) and up to 1 9/16" (40mm). Glazing space of 1/8" (3mm) over glazing material thickness is standard, allowing for glazing tape to be used on both sides of the glazing material. In order to maintain fire rating, glazing material should also be U.L. and/or W.H.I. listed.

MATERIAL: SG-10 is: 10 GA. (3.4mm) C.R.S. Frame on glass 3/16" (5mm) to 1" (25mm) thick.

FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: By drilling 1/4" (6mm) holes thru the door around

the perimeter of the door cutout. Vision Frame has countersunk mounting holes for #8x32 one way vandal proof security screw thru bolts with a blank head on one side for a flush appearance, and improved security. Sliding door frame fits over vision frame, and installs with #8 x 3/4" one way vandal proof security screws.

DOOR THICKNESS: For 1 3/4" (44mm) (std), or up to 2 1/4" (57mm) (specify).


SPECIALS: Fractional sizes and other steel gauges (contact factory)

MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized (Zinc Plated).FINISH: Custom Baked Enamel Colors (as per sample chip supplied).FASTENERS: Special Security Screw Fasteners, See page 26, this secion.


12 GA. (2.5mm) C.R.S. Frame on glass over 1" (25mm) to 1 9/16" (40mm) thick.

SSD is: 12 GA. (2.5mm) C.R.S. Frame and Sliding Door.

NOTE: Door slides from side to side. Non-centered vision frame cutout is generally required.

60/90 MINUTE: Approved listing at 100 sq.in. (0.065 m2) visible litemax. width 10" (254mm), max. height 33" (838mm).


NOTE: Width O.D. DIMENSION of SSD portion will be double the width of actual Door Order / Cutout size plus 6-1/4". Height O.D. DIMENSION will be actual Door Order / Cut-out size plus 4-3/4". Please consider your door width when ordering. EXAMPLE: 12"X12" Order/Cut-out size= 30-1/4"(12"+12"+6-1/4")x16-3/4"(12"+4-3/4")RECOMMENDATION: Do Not make cutouts in door prior to receiving SSD products. PULL

HANDLE

DETAIL DRAWING

TECHNICAL DATAFROM

SG-10-SSDHIGH SECURITY

METAL VISION FRAME WITH SECURITY SLIDING DOOR





WARNOCK HERSEY

FIRERATINGS










FORMEDPULL

HANDLE

ORDE

R SIZE

+ 4 3

/4" (1

21mm

)

DOOR

CUTO

UT +

1 1/2"

(38m

m)O.D.

FRAMESSD

FRAMEO.D.

1 5/8" (41mm)

GLASS THICKNESS1/8" (3mm) OVERGLAZING SPACE

9/16" (14mm)

2" (51mm)

MINU

S 6 3/

4" (17

1mm)

HEIG

HT =

ORDE

R SIZE

3/8" (10mm)

MINU

S 1" (2

5mm)

WIDT

H = O

RDER

SIZEVi

sible

Lite

Heigh

t

DOOR

CUT

OUT

HEIG

HT

Visible Lite

DOOR CUTOUTWIDTH


THICKNESS

1 3/4"(44mm)

OR SPECIFY

WIDT

H = O

RDER

SIZE

MINU

S 2 1/

4" (57

mm)

HEIG

HT =

ORDE

R SIZE

MINU

S 4 3/

4" (10

8mm)

HEIG

HT =

VISIBL

E LITE

+ 6 1

/4" (1

59mm

)WI

DTH

= VIS

IBLE L

ITE +

2 1/4"

(57m

m)

NOTE: Width O.D. DIMENSION of SSD portion will be double the width of actual Door Order / Cutout size plus 6-1/4". Height O.D. DIMENSION will be actual Door Order / Cut-out size plus 4-3/4". Please consider your door width when ordering. EXAMPLE: 12"X12" Order/Cut-out size= 30-1/4"(12"+12"+6-1/4")x16-3/4"(12"+4-3/4")RECOMMENDATION: Do Not make cutouts in door prior to receiving SSD products.


DETAIL DRAWING

TECHNICAL DATAFROM

SG-10-SP-SSDHIGH SECURITY

METAL VISION FRAME WITHSPEAK PORT AND

SECURITY SLIDING DOOR


FIRE RATINGS




■ MATERIAL: SG-10 is: 10 GA. (3.4mm) C.R.S. Frame on glass 3/16" (5mm) to 1" (25mm) thick. 12 GA. (2.5mm) C.R.S. Frame on glass over 1" (25mm) to 1 9/16" (40mm) thick. SSD is: 12 GA. (2.5mm) C.R.S. Frame and Sliding Door.SPEAK PORT: Two 10 GA. (3.4mm) C.R.S. plates with perforated faces with5/32" (4mm) diameter holes on 7/32" (5.6mm) staggered centers.

■ FINISH: Grey Primer, Beige or Bronzed Baked Enamel■ INSTALLATION: By drilling 1/4" (6mm) holes thru the door around the

perimeter of the door cutout. Vision Frame hascountersunk mounting holes for #8x32 one way vandalproof security screw thru bolts with a blank head on oneside for a flush appearance, and improved security. Slidingdoor frame fits over vision frame, and installs with #8 x 3/4"one way vandal proof security screws.

■ DOOR THICKNESS: For 1 3/4" (44mm) (std), or up to 2 1/4" (57mm) (specify)■ GLAZING: Thickness can range from 3/16" (5mm) and up to 1 9/16" (40mm).

Glazing space of 1/8" (3mm) over glass thickness is standard,allowing for glazing tape to be used on both sides of the glazingmaterial.

■ MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized(Zinc Plated).

■ FINISH: Custom Baked Enamel Colors (as per sample chip supplied)■ FASTENERS: Special Security Screw Fasteners. See page 26, this section.■ SPECIALS: Fractional sizes and other steel gauges (contact factory).

■ SG-10-SP-SSD is not fire rated.

■ NOTE: For exterior use, High Humidity or Salt Air application, productmust be Galvanized or Stainless Steel.

■ IMPORTANT: Interpretation of building and fire codes may vary. Consult withthe local authority having jurisdiction in your area, to determineappropriate standards.


GLAZINGSPACE

3/8"(10mm)

ORDE

R SIZE

MINU

S 1"

ORDE

R SIZE

PLUS

1" (2

5mm)

GLAZINGMATERIAL

FRAMEO.D.

ORDE

R SIZE

MINU

S 2"

9/16" (14mm)1 5/8"

ORDE

R SIZE

PLUS

4 3/4

" (121

mm)

1 3/4"

#8 x 3/4"ONE WAY

VANDAL PROOFSECURITY SCREW

VISION

FRAMEO.D.SSD

OUTSIDE INSIDE

(41mm)

(25mm

)

(50mm

)

(44mm)

1 1/2" TYP.(38mm)

5/64" (2mm)

PULL HANDLE

DOOR ONLY

1/4"(6mm)GLAZINGMATERIAL

ORDERSIZE

&DOOR

CUTOUT

VISIBLELITE

Visible Lite

Width

Visib

le Lit

e He

ight

DOOR

CUT

OUT

HEIG

HT

DOOR CUTOUTWIDTH

FORMEDPULL

HANDLE

NOTE: Width O.D. DIMENSION of SSD portion will be double the width of actual Door Order / Cutout size plus 5-1/4". Height O.D. DIMENSION will be actual Door Order / Cut-out size plus 4-3/4". Please consider your door width when ordering. EXAMPLE: 12"X12" Order/Cut-out size= 29-1/4"(12"+12"+5-1/4")x16-3/4"(12"+4-3/4")RECOMMENDATION: Do Not make cutouts in door prior to receiving SSD products.


DETAIL DRAWING

TECHNICAL DATAFROM

LoPro™-SSDLO-PROFILE

METAL VISION FRAME WITHSECURITY SLIDING DOOR





WARNOCK HERSEY

FIRERATINGS





■ MATERIAL: LoPro: 20 GA. (1mm) (C.R.S. FrameSSD: 12 GA. (2.5mm) C.R.S. Frame and Sliding Door

■ FINISH: Grey Primer, Beige or Bronze Baked Enamel■ INSTALLATION: Uses 1-3/4" (44mm) one way vandal proof sheet

metal screws that pass thru the door cut-out, andfastens to the opposite side of the vision frame, thuseliminating the need to drill the door for thru bolt andsaving installation time and labor. Sliding door framefits over vision frame, and installs with #8 x 3/4" oneway vandal proof security screws.

■ DOOR THICKNESS: For 1-3/4" (44mm) Wood or Metal doors.■ GLAZING: Should be 1/4" (6mm) or 3/16" (5mm) fire rated with U.L.

and/or W.H.I. classification markings. Nominal glazingspace of 3/8" (19mm) allows for glazing tape to be used onboth sides of the glass (See Glass and Glazing section).

■ NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel

■ MATERIAL: #304 or #316 Stainless Steel, #4 Finish (satin), Galvanized(Coil, Hot Dipped, or Zinc Plated). SSD - Zinc Plated Only.

■ FINISH: Custom Baked Enamel Colors ( as per sample chip supplied).■ FASTENERS: Special Security Screws Fasteners, See page 26, this section.■ SPECIALS: Fractional sizes

■ 20/45 MINUTE: Approved listing at 1296 sq. in. (0.836 m2) visible lite.max. width 54" (1372mm), max. height 54" (1372mm)

■ 60/90 MINUTE: Approved listing at 100 sq. in. (0.065 m2) visible lite.max. width 10" (254mm), max. height 33" (838mm)

■ IMPORTANT: Interpretation of building and fire codes may vary. Consultwith the local authority having jurisdiction in your area todetermine appropriate standards.




2"(51mm)

FRAMEO.D.

FASTENERS: Special Security Screw Fasteners, See catalog page 26 this section. FINISH: Custom Baked Enamel Colors (as per sample chip supplied).MATERIAL: #304 or #316 Stainless Steel, Galvanized (Hot Dipped or Zinc Plated).


DOOR THICKNESS: For 1 3/4" (44mm) (Std), or up to 2 1/4" (57mm) thick

INSTALLATION: By drilling 1/4" (6mm) holes thru the door, around the perimeter of the door cutout. Both sides of the frame have countersunk mounting holes for #8x32 one way vandal proof security screw thru bolts thru bolts with a blank head on one side for improved security.


MATERIAL: 7 GA. (4.6mm) Cold Rolled Steel face plate frame.Standard SG-10,12 GA. (2.5mm) back plate frame.

USES: For areas where bullet resistance or protection fromSPECIALS: Fractional sizes, Glazing (1/4 to 1-9/16"), and Door thicknesses, up to 2 1/4".

INSIDEBULLET RESISTANT SIDE

forced entry or attack is required.


max. width 35" (889mm), max. height 35" (889mm).60*/90* MINUTE: Approved listing at 1080 sq.in. (0.697 m2) visible lite


GLAZING: Thickness can range from 3/16" (5mm) up to 1 9/16" (40mm), depending on bullet resistance level, fire or attack standard required. Glazing space of 1/8" (3mm) over glazing material is standard, allowing for glazing tape to be used on both sides of the glazing material.

Bullet Resistance Test (Passed): .44 Magnum and 12 Gauge Shotgun, UL 752-LVL-III.Impact Test (Passed): Sledge Hammer attack portion of C.D.C. test requirements.


7 GA. C.R.S. FRAME

12 GA. C.R.S. FRAME

3/8"(10mm)

ORDE

R SI

ZE M

INUS

1/4

"(6

mm

)

ORDE

R SI

ZE P

LUS

1 1/

2" (3

8mm

)

ORDE

R SI

ZEM

INUS

2 1

/2" (

64m

m)

GLAZINGSPACE1/8" (3mm)OVER GLASSTHICKNESS

ORDERSIZE

&DOOR

CUTOUT

VISIBLELITE

GLAZINGMATERIAL

1 3/4"(44mm)

OR SPECIFY


THICKNESS


*Must be used with 1-1/16" (27mm) or 1-9/16" (40mm) Pyrostop and fire listed glazing tape, and be used in an appropriately tested door assembly.


DETAIL DRAWING

TECHNICAL DATAFROM

BR-7BULLET AND IMPACT RESISTANT

METAL VISION FRAME


BULLET RESISTANCE, PHYSICAL ATTACK



WARNOCK HERSEY

FIRERATINGS






IMPACT RATINGS







ORDE

R SIZE

FRAMEO.D.

OUTSIDEINSIDE

GLAZINGSPACE1/8" (3mm)

THICKNESS

CAM LOCK

ORDE

R SIZE

SECURITYGLAZING

MATERIAL

OVER GLASS MINU

S 2 1/

2" (64

mm)

ORDE

R SIZE

LITE

3/8" (10mm)

VISIBLE

2" (51mm)

MINU

S 1/4"

(6mm

)

PLUS

1 1/2

" (38m

m)

WITH KEY

12GA.


SECURITY COVER

ORDER

CUTOUTDOOR

&SIZE

1 3/4"(44mm)

OR SPECIFY


THICKNESS

PULL HANDLE

SECURITYCAM LOCK

CONTINUOUS HINGE SPOT WELDED

TOP VIEW

WITH KEYPULL

HANDLE

PULLHANDLE

PINNED TORX SECURITY THRU BOLTS

DETAIL DRAWING

TECHNICAL DATAFROM

SG-12-LSCHIGH SECURITY

METAL VISION FRAME WITHLOCKING SECURITY COVER




WARNOCK HERSEY

FIRERATINGS



■ MATERIAL: 12 GA. (2.5mm) Cold Rolled Steel.■ SECURITY COVER: 12 GA. (2.5mm) C.R.S. operating panel spot

welded with continuous hinge to one side of metalvision frame. Opens with a metal pull handle. Dooris secured with a key operated cam lock.

■ FINISH: Grey Primer, Beige or Bronze Baked Enamel■ INSTALLATION: By drilling 1/4" (6mm) holes thru the door, around the

perimeter of the door. Frame has countersunk mountingholes for #8x32 Pinned Torx security screw thru boltswith a blank head on one side for flush appearance.

■ DOOR THICKNESS: For 1 3/4" (44mm) (std), or up to 2 1/4" (57mm)(specify).

■ GLAZING: Thickness can range from 3/16" (5mm) up to 1 9/16" (40mm). Glazing space of 1/8" (3mm) over glass thickness isstandard, allowing for glazing tape to be used on both sidesof the glazing material.

■ IMPORTANT: Interpretation of building and fire codes may vary. Consultwith local authority having jurisdiction in your area, todetermine appropriate standards.

■ NOTE: For Exterior use, High Humidity or Salt Air application, productmust be Galvanized or Stainless Steel.

■ MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized (Hot Dipped,or Zinc Plated)

■ FINISH: Custom Baked Enamel Colors (as per sample chip supplied). PlatedFinishes to match the lock, hinges and closer.

■ FASTENERS: Special Security Screw Fasteners, See page 26, this section.■ SPECIALS: Fractional Sizes, Glass 3/16” to 1 9/16”) and Door (up to 2 1/4”).

■ 20/45/60* MINUTE: Approved listing at 1296 sq. in. (0.836 m2) visible lite.max. width 54" (1372mm), max. height 54" (1372mm).

■ 60**/90** MINUTE: Approved listing at 1080 sq. in. (0.697 m2) visible lite.max. width 35" (889mm), max. height 35" (889mm).

■ 60/90 MINUTE: Approved listing at 100 sq. in. (0.065 m2) visible lite.max. width 10" (254mm), max. height 33" (838mm).

*Must be used with FIRELITE Plus or NT and Fire listed glazing tape or anothermanufacturer’s equivalent product. Glazing combination must be used inappropriately tested door assembly.**Must be used with 7/8" (23mm) or 1-1/16" (27mm) Pyrostop and fire listed glazingtape, and be used in an appropriately tested door assembly.

IMPACT RATINGS












WARNOCK HERSEY

FIRERATINGS


your area, to determine appropriate Standards.Consult with the local authority having jurisdiction in


MATERIAL: 18 GA. (1.25mm) Cold Rolled Steel.


perimeter of the door cutout. Frame has countersunk mounting holes for #8x32 Pinned Torx security screw thru bolts with a blank head on one side for flush appearance.

DOOR THICKNESS: For 1 3/4" (44mm) Wood and Metal Doors.GLAZING: Should be 1/4" (6mm). Glazing space of 5/16" (8mm) allows

for glazing tape to be used on both sides of the glass.

SECURITY COVER: 18 GA. (1.25mm) C.R.S. operating panel spot weldedwith continuous hinge to one side of

MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized (Sheet,Hot Dipped, or Zinc Plated).


FASTENERS: Special Security Screw Fasteners, See Page 26, this section. SPECIALS: Fractional Sizes, Lead Lined for X-ray applications,

for Glass or Door thickness (FGS-IS-SC).

must be Galvanized or Stainless Steel.NOTE: For exterior use, High Humidity or Salt Air application, product

metal vision frame. Closes to a magneticlatch. Opens with a metal pull handle.



FRAMEO.D.

INSIDE OUTSIDE

LATCHMAGNETIC

18 GA. CRS.SECURITY COVER

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE VISIBLE

LITE

1/4"(6mm)

3/8"(10mm)

5/16"(8mm)

GLAZINGSPACE

1 1/4"(32mm)

ORDE

R SI

ZE M

INUS

1" (

25m

m)

ORDE

R SI

ZE M

INUS

1/4

" (6m

m)

ORDE

R SI

ZE P

LUS

1 1/

2" (3

8mm

)

1 3/4"(44mm)DOORONLY

1/4"(6mm)

1/4"(6mm)

GLAZINGMATERIAL

PULLHANDLE

TOP VIEW

CONTINUOUS HINGE SPOT WELDEDMAGNETIC

LATCH

PULLHANDLE

PULL HANDLE

20/45/60*/90* MINUTE: Approved listing at 1296 sq.in. (0.836 m2) visible litemax. width 54" (1372mm), max. height 54" (1372mm).

* Must be used with FIRELITE Plus or NT and Fire listed glazing tape or another manufacturer’s equivalent product. Glazing combination must be used in appropriately tested door assembly.

TECHNICAL DATAFROM

DETAIL DRAWING

FGS-75-SCMETAL VISION FRAME

WITHOPERATING

SECURITY COVER









ORDE

R SI

ZE M

INUS

1/4

" (6m

m)

ORDE

R SI

ZE P

LUS

1 1/

2" (3

8mm

)FRAME

O.D.


ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE

1 3/4"(44mm)

1/4"(6mm)

3/8"(10mm)

5/16"(8mm)

GLAZINGSPACE

1 1/4"(32mm)

ORDE

R SI

ZE M

INUS

1"

(25m

m)

INSIDE OUTSIDE

DOORONLY

1/4"(6mm)

VISIBLELITE

1/4"(6mm)

GLAZINGMATERIAL


PULL HANDLE



CAM LOCKWITH KEY

SECURITY

TOP VIEW

PULLHANDLE

PULLHANDLE

DETAIL DRAWING

TECHNICAL DATAFROM

FGS-75-LSCMETAL VISION FRAME

WITH LOCKING SECURITY COVER





WARNOCK HERSEY

FIRERATINGS





■ MATERIAL: 18 GA. (1.25mm) Cold Rolled Steel.■ SECURITY COVER: 18 GA. (1.25mm) C.R.S. operating panel spot

welded with continuous hinge to one side of metalvision frame. Door is secured with key operatedcam lock. Opens with a metal pull handle.

■ FINISH: Grey Primer, Beige or Bronze Baked Enamel■ INSTALLATION: By drilling 1/4" (6mm) holes thru the door,

around the perimeter of the door. Frame hascountersunk mounting holes for #8x32 PinnedTorx security screw thru bolts with a blank headon one side for flush appearance.

■ DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.■ GLAZING: Should be 3/16" (5mm) to 1/4" (6mm) only. Glazing space

of 5/16" (8mm) allows for glazing tape to be used on bothsides of the glass.

■ IMPORTANT: Interpretation of building and fire codes may vary.Consult with local authority having jurisdiction in yourarea, to determine appropriate standards.

■ MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized(Sheet, Hot Dipped, or Zinc Plated)


■ FASTENERS: Special Security Screw Fasteners, See page 26, this section.■ SPECIALS: Fractional Sizes, Lead Lined for X-Ray applications, For other

Glass or Door thickness (FGS-IS-LSC).

■ 20/45/60*/90* MINUTE: Approved listing at 1296 sq. in. (0.836 m2) visible lite.max. width 54" (1372mm), max. height 54" (1372mm)

*Must be used with FIRELITE Plus or NT and Fire listed glazing tape oranother manufacturer’s equivalent product. Glazing combination must beused in appropriately tested door assembly.

■ NOTE: For Exterior use, High Humidity or Salt Air application, productmust be Galvanized or Stainless Steel.







WARNOCK HERSEY

FIRERATINGS



PINNED TORX SECURITY SCREWS

1 3/4"(44mm)

5/64"(2mm)

DOOR

3/8" (10mm)

GLAZINGSPACE

1/4" (6mm)

ORDE

R SI

ZE M

INUS

2"(5

1mm)

VISIBLELITE

ORDE

R SI

ZE M

INUS

1" (

25m

m)

ORDE

R SI

ZE P

LUS

1" (2

5mm

)

FRAMEO.D.

INSIDE OUTSIDE

ONLY


1" (25mm)11/16"

(17mm)

1/2" (13mm)

MATERIALGLAZING

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE

5/64"(2mm)

PULL HANDLE

LATCHMAGNETIC

PULLHANDLE

TOP VIEW

CONTINUOUS HINGESPOT WELDED

PULLHANDLE MAGNETIC

LATCH

DETAIL DRAWING

TECHNICAL DATAFROM

LoPro™-SCMETAL VISION FRAME

WITH OPERATING

SECURITY COVER





■ MATERIAL: LoPro is: 20 GA. (1mm) C.R.S. Operating Security Cover: 18 GA. (1.25mm) C.R.S.

■ SECURITY COVER: 18 GA. (1.25mm) C.R.S. operating panel spot weldedwith continuous hinge to one side of metal visionframe. Closes to a magnetic latch. Opens with a metalpull handle.

■ FINISH: Grey Primer, Beige or Bronze Baked Enamel.■ INSTALLATION: Vision Frame (LoPro) uses 1 3/4" (44mm) Pinned Torx

security sheet metal screws that pass through the doorcutout, and fastens to the opposite side of the vision frame,thus eliminating the need to drill the door for thru bolts andsaving installation time and labor.

■ DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Door.■ GLAZING: Should be 1/4" (6mm), 3/16" (5mm) or 5/16" (8mm) glazing

material. Nominal glazing space of 3/8" (10mm) allows forglazing tape to be used on both sides of the glass. (See Glassand Glazing Materials section)

■ NOTE: For Exterior use, High Humidity or Salt Air application,product must be galvanized or Stainless Steel.

■ MATERIAL: #304 or #316 Stainless Steel, #4 Finish, Galvanized (Coil, HotDipped, or Zinc Plated).


■ FASTENERS: Special Security Screws, See page 26, this section.■ SPECIALS: Fractional sizes.

■ 20/45/60*/90* MINUTE: Approved listing at 1296 sq. in. (0.836 m2) visible lite.max. width 54" (1372mm), max. height 54" (1372mm)

■ 3 HOUR:* Approved listing at 100 sq. in. visible lite. max. width 12" (305mm), max.height 33" (838mm)

*Must be used with FIRELITE Plus or NT and Fire listed glazing tape or anothermanufacturer’s equivalent product. Glazing combination must be used inappropriately tested door assembly.

■ IMPORTANT: Interpretation of building codes may vary. Consult with the local authorityhaving jurisdiction in your area, to determine appropriate standards.

DETAIL DRAWING

TECHNICAL DATAFROM

LoPro™-GRLO-PROFILE

METAL VISION FRAME WITHSECURITY GRILLE ONE SIDE





WARNOCK HERSEY

FIRERATINGS






based on component manufacturers tolerances.Actual dimensions are nominal and may varyAnemostat manufacturing dimensions ±1/32

MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized(Hot Dipped, or Zinc Plated).



SPECIALS: Fractional Sizes. For Special Glass Thickness

MATERIAL: 20 GA. (1mm) Cold Rolled Steel with 16 GA. grille welded to frame.FINISH: Grey Primer, Beige or Bronze Baked Enamel.

DOOR THICKNESS: Specified by customer, 1 3/4" (44mm) is standard.AESTHETICS: Tight mitered corners, beveled glass stop and

a low profile to provide a clean, tapered look.



GLAZING: Tolerance variances in door or glass thickness andtype of glazing tape used will affectglazing space, as related to nominal glass dimensions

Materials Section).

*and vision frame used (see Glass and Glazing

(LoPro™-IS-GR) up to 3/4" (19mm)

11/16"

ORDE

R SIZE

MINU

S 2"

1/2" (13mm)

1" (25mm)

OR SPECIFY

5/64"5/64"

O.D.

PLUS

2" (5

1mm)

VISIBL

E LITE

ORDE

R SIZE

IS

ORDE

R SIZE

PLUS

1" (2

5mm)

FRAME

MINU

S 1" (2

5mm)

ORDE

R SIZE

1 3/4"(44mm)

(17mm)

(51mm

)

(2mm) (2mm)

GLAZING SPACE

GLAZING MATERIAL3/16" TO 1/4"

(5mm to 6mm)*

*16 GA. SECURITY GRILLE13/16" SQ. HOLES ON 1" CENTERS.

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE

VISIBLELITE

OUTSIDE INSIDE

5/16" (8mm)

GLAZING SPACE and THICKNESS of GLAZING TAPE or COMPOUND USED WILL VARY BASED on GLAZING MATERIAL THICKNESS*

16 GA. (1.7mm)SECURITY

GRILLE

INSTALLATION: Uses 1 3/4" (44mm) one way vandal proof security sheet metal screws that pass through the door cutout, and fastens to the opposite side of the vision frame, thus eliminating the need to drill the door for thru bolts and saving installation time and labor. It also leaves the corridor side of the frame free of fasteners for added security and a cleaner, more aesthetic appearance.

■ 20/45/60*/90* MINUTE: Approved listing at 1296 sq. (0.836 m2) in. visible lite.max. width 54" (1372mm), max. height 54" (1372mm)

■ 3 HOUR:* Approved listing at 100 sq. in. (0.065 m2) visible lite. max. width 12" (305mm), max. height 33" (838mm)





WARNOCK HERSEY

FIRERATINGS


PINNED TORX SECURITY SCREWS

based on component manufacturers tolerances.Actual dimensions are nominal and may varyAnemostat manufacturing dimensions ±1/32

MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized(Hot Dipped, or Zinc Plated).



SPECIALS: Fractional Sizes. For Special Glass Thickness

MATERIAL: 20 GA. (1mm) Cold Rolled Steel with 16 GA. grille welded to frame.

FINISH: Grey Primer, Beige, or Bronze Baked Enamel.

SECURITY COVER: 16 GA. (1.7mm) C.R.S. operating panel spot welded with

DOOR THICKNESS: Specified by customer, 1 3/4" (44mm) is standard.AESTHETICS: Tight mitered corners, beveled glass stop and

a low profile to provide a clean, tapered look.


GLAZING: Tolerance variances in door or glass thickness and type of glazing tape used will affect glazing space, as related to nominal glass dimensions and vision frame used (see Glass and GlazingMaterials Section).

*

continuous hinge to one side of metal vision frame. Closes to a magnetic latch. Opens with a metal pull handle.

(LoPro™-IS-SC-GR) up to 3/4" (19mm)

11/16"

ORDE

R SIZE

MINU

S 2"

1/2" (13mm)

1" (25mm)

OR SPECIFY

5/64"5/64"

O.D.

PLUS

2" (5

1mm)

VISIBL

E LITE

ORDE

R SIZE

IS

ORDE

R SIZE

PLUS

1" (2

5mm)

FRAME

MINU

S 1" (2

5mm)

ORDE

R SIZE

1 3/4"(44mm)

(17mm)

(51mm

)

(2mm) (2mm)

GLAZING SPACE

GLAZING MATERIAL3/16" TO 1/4"

(5mm to 6mm)*

*16 GA. SECURITY GRILLE13/16" SQ. HOLES ON 1" CENTERS.

MAGNETIC LATCH


OPERATINGSECURITY COVER

ORDERSIZE

&DOOR

CUTOUT

GLASSSIZE

VISIBLELITE

OUTSIDE INSIDE

5/16" (8mm)

PULL HANDLE

GLAZING SPACE and THICKNESS of GLAZING TAPE or COMPOUND USED WILL VARY BASED on GLAZING MATERIAL THICKNESS*

PULL HANDLE

OPERATINGSECURITY COVER

16 GA. (1.7mm) SECURITY

GRILLE

INSTALLATION: Uses 1 3/4" (44mm) Pinned Torx security sheet metal screws that pass through the door cutout, and fastens to the opposite side of the vision frame, thus eliminating the need to drill the door for thru bolts and saving installation time and labor. It also leaves the corridor side of the frame free of fasteners for added security and a cleaner, more aesthetic appearance.


TOP VIEW

PULL HANDLE

MAGNETICLATCH

DETAIL DRAWING

TECHNICAL DATAFROM

LoPro™-SC-GRLO-PROFILE

METAL VISION FRAME WITHSECURITY GRILLE ONE SIDE ANDOPERATING SECURITY COVER





■ 20/45/60*/90* MINUTE: Approved listing at 1296 sq. (0.836 m2) in. visible lite.max. width 54" (1372mm), max. height 54" (1372mm)

■ 3 HOUR:* Approved listing at 100 sq. in. (0.065 m2) visible lite. max. width 12" (305mm), max. height 33" (838mm)



DOOR THICKNESS: 1 3/4" (44mm) (std), or up to 2 1/4" (57mm) (specify).

MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), GalvanizedHot Dipped or Zinc Plated). Not available in Galvanized Sheet.


FASTENERS: Special Security Screw Fasteners, See Page 26, this section.

SPECIALS: Fractional Sizes, Lead Lined for X-ray applications.




GLAZING: Thickness can range from over 3/16" (5mm) and up to 1 9/16" (40mm). Glazing space of 1/16" (1.6mm) over glass thickness is standard, allowing for glazing tape to be used on both sides of the glass.

MATERIAL: 18 GA. (1.25mm) Cold Rolled Steel Frame, with 12 GA. (2.5mm) Cold Rolled Steel Security Grille, 13/16" (21mm) square Holes on 1" (25mm) centers).

USES: For use where visible lite is required, but security onone or both sides of the glass is necessary.

VISIBLELITE

GLASSSIZE

FRAMEO.D.

INSIDE OUTSIDE

GLAZINGSPACE1/16" (2mm) OVER GLASSTHICKNESS

ORSPECIFY

13/16"(21mm)

3/16"(5mm)

Special Glass or Door Thickness.

Also available with SecurityGrille on one side only( )


THICKNESS

12 GA. C.R.S.FRAME / SECURITYGRILLE FACE PLATE(WITH 13/16" SQ. HOLES ON 1" CTRS)

IMPORTANT: Interpretation of building and fire codes may vary. Consult with the local authority having jurisdiction in your area, to determine appropriate standards.


ORDERSIZE

&DOOR

CUTOUT

1/4"(6mm)

3/8"(10mm)

1 1/4"(32mm)

ORDE

R SIZE

MINU

S 1" (2

5mm)

ORDE

R SIZE

MINU

S 1/4"

(6mm

)

ORDE

R SIZE

PLUS

1 1/2

" (38m

m)

1 3/4"(44mm) 1/4"

(6mm)


GRILLE

DETAIL DRAWING

TECHNICAL DATAFROM

SL-ISMETAL VISION FRAME

WITH SECURITY GRILLE FORSTANDARD/SPECIAL DOOR OR

GLASS THICKNESS





WARNOCK HERSEY

FIRERATINGS





■ 20/45/60* MINUTE: Approved listing at 1296 sq. in. (0.836 m2) visible lite.max. width 54" (1372mm), max. height 54" (1372mm).

■ 60**/90** MINUTE: Approved listing at 1080 sq. in. (0.697 m2) visible lite.max. width 35" (889mm), max. height 35" (889mm).


*Must be used with FIRELITE Plus or NT and Fire listed glazing tape oranother manufacturer’s equivalent product. Glazing combination mustbe used in appropriately tested door assembly.**Must be used with 7/8" (23mm) or 1-1/16" (27mm) Pyrostop and firelisted glazing tape, and be used in an appropriately tested door assembly.

TEMP

ERED

GLA

SS

TEMP

ERED

GLA

SS

GLASSSIZE

(MIDDLE)GLASSSIZE

DOOR ONLY

VISIBLELITE

1 5/8"(41mm)

ORDE

R SI

ZE P

LUS

1 7/

16" (

37m

m)

FRAMEO.D.

INSIDE OUTSIDEFIR

E & SA

FETY

RATE

D GLA

SS

ONE WAY VANDAL PROOF

SCREWS

FGS-MS3-FRFGS-MS5-FR

ORDERSIZE

&DOOR

CUTOUT


1/4"(6mm)

3/8"(10mm)

1 3/4"(44mm) 1/4"

(6mm)

1/4"(6mm)

ORDE

R SI

ZEM

INUS

1 1

/4" (

32m

m)

1/4"(6mm)

1/4"(6mm)

1/4"(6mm)1/4"

(6mm)

ORDE

R SI

ZEM

INUS

1/4

" (6m

m)

ORDE

R SI

ZEM

INUS

1 3

/4" (

44m

m)

DETAIL DRAWING

TECHNICAL DATAFROM

FGS-MS-FRMETAL VISION FRAMEIMPACT AND SECURITY

RESISTANT



IMPACT / SAFETY RATINGS



WARNOCK HERSEY

FIRERATINGS





■ MATERIAL: 18 GA. (1.25mm) Cold Rolled Steel Frame■ FINISH: Grey Primer, Beige or Bronze Baked Enamel■ INSTALLATION: By drilling 1/4" (6mm) holes thru the door, around the

perimeter of the door cutout. Frame has countersunkmounting holes for #8x32 one way vandal proofsecurity screw thru bolts with a blank head on oneside for flush appearance.

■ DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors.■ GLAZING: Incorporates use of 1/4" (6mm) SAFE-Wire™ glass or 3/16" (5mm)

FireLite® NT with 1/4" (6mm) tempered glass on the inside and/oroutside of the security installation (must be purchased with frame).

■ USES: Where impact and fire ratings are both required. Mediumsecurity installations such as psychiatric hospitals.

■ NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel

■ IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction in yourarea to determine appropriate standards.

■ MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized (Coil,Hot Dipped, or Zinc Plated)

■ FINISH: Custom Baked Enamel (as per sample chip supplied). Plated finishesto match the lock, hinges and closer.

■ FASTENERS: Special Security Screw Fasteners, see page 26 this section.■ SPECIALS: Fractional sizes, Lead Lined for X-ray applications. Glass or Door

Thickness (See SL-IS, SG-10 or FGS-IS). For Lead Lined and FireRated, FGS-MS-5 must be used. Leaded and Fire Rated Glassmust be supplied with FGS-MS-5 to maintain fire ratings.

■ 20/45/60*/90* MINUTE: Approved listing at 1296 sq. in. (0.836 m2) visible lite.max. width 54" (1372mm), max. height 54" (1372mm).



Meets ANSI.Z97.1 and CPSC 16CFR-1201 (Cat. I and II)




FGS-MS is not fire rated.

MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized (Coil,Hot Dipped, or Zinc Plated).


FASTENERS: Special Security Screw Fasteners, See Page 26, this section.

SPECIALS: Fractional Sizes, Lead Lined for X-ray applications.

FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: By drilling 1/4" (6mm) holes thru the door, around

the perimeter of the door cutout. Frame has countersunk mounting holes for #8x32 one way vandal proof security screw thru bolts with a blank head on one side for flush appearance.

DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors



MATERIAL: 18 GA. (1.25mm) Cold Rolled Steel Frame.

GLAZING: Incorporates use of 1/4" (6mm) safety rated glazingwith 1/4" (6mm) and/or 1/2" (13mm) glazing material on interiorand/or exterior security installations.

USES: Products are designed for high and medium securityinstallations where protection from vandalism, orforced entry/exit is necessary.

DOOR ONLY

POLY

CARB

ONAT

E

POLY

CARB

ONAT

E

ORDE

R SIZE

PLUS

1 7/

16" (3

7mm)

1 5/8"(41mm)

VISIBLELITE

FRAMEO.D.

INSIDE OUTSIDEOR

DER S

IZE

ORDE

R SIZE

MINU

S 1 1/

4" (32

mm)

GLAZINGMATERIAL

SIZE

MINU

S 1/4"

(6mm

)

GLASSSIZE

(MIDDLE)

(For Fire Rating see FGS-MS-FR, page 18, this section)

1/4"(6mm)

1/4"(6mm)

1/4"(6mm)

1/2"(13mm)

1/4"(6mm)

3/8"(10mm)

1 3/4"(44mm)

1/4"(6mm)

1/4"(6mm)

ORDE

R SI

ZEM

INUS

1 3

/4" (

44m

m)

1/2"(6mm)

1/2"(13mm)

FGS-MS1

ORDERSIZE

&DOOR

CUTOUT

FGS-MS4 FGS-MS5

FGS-MS2 FGS-MS3

1/2"(13mm)

1/4"(6mm)

1/4"(6mm)

1/4"(6mm)

1/4"(6mm)

1/4"(6mm)


TECHNICAL DATAFROM

DETAIL DRAWING

FGS-MSMETAL VISION FRAME

HIGH SECURITYIMPACT RESISTANT


FIRE RATINGS








3/16"(5mm)

(21mm)13/16"

(32mm)

(6mm)(6mm)

16 GA. (1.7mm) Security Cover

GLAZING TAPE: Framed screen is held in place with glazing tape on both sides, sandwiched between the security grilles using 1/16" thick, closed cell polyvinyl chloride foam tape sealant with pressure sensitive adhesive two sides.

SCREEN: Framed screen incorporates #304 stainless steel screen wire, .009" (.228mm) thick, using a 18-18 mesh to restrict penetration from insects. Screen material is installed into a .020" (.508mm) thick mill finished aluminum frame.

SECURITY COVER: 16 GA (1.7mm) CRS operating panel, spot welded with continuous hinge to one side of the metal vision frame. Closes with a key operated cam lock.


LOCK WITH KEYSECURITY CAM

USES: For use where ventilation is required, but security on one or both sides of the screen is necessary, i.e. kitchen doors in schools or restaurants.

FRAMEDSTAINLESSSTEEL SCREEN

)( Grille on one side onlyAlso available with Security

OR OTHER(44mm)

1/4" 1/4"1 3/4"

THICKNESSOVER SCREEN1/16" (2mm)GLAZING SPACE

OUTSIDEINSIDE

O.D.FRAME

ORDE

R SIZE

PLUS

1 1/2

" (38m

m)SIZE

SCREEN

ORDE

R SIZE

MINU

S 1/4"

(6mm

)

3/8" (10mm)

1 1/4"

LITEVISIBLE

ORDE

R SIZE

MINU

S 1" (2

5mm)

MATERIAL: Frame is 18 GA (1.25mm) CRS with 12 GA (2.5mm) CRS Security Grille two sides, 13/16" (21mm) square holes on 1" (25mm) centers welded to each side of vision frame.

your area, to determine appropriate standards. Consult with the local authority having jurisdiction inIMPORTANT: Interpretation of building and fire codes may vary.


DOOR THICKNESS: Specified by customer, 1 3/4" (44mm) is standard).


SPECIALS: Fractional Sizes, Gauge.FASTENERS: Special Security Screw Fasteners. See page 26, this section.

Plated Finishes to match the lock, hinges and closer.FINISH: Custom Baked Enamel Colors (as per sample chip supplied).

(Hot Dipped or Zinc Plated). Not available in Galvanized Coil.MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized

CUTOUTDOOR

&SIZE

ORDER

12 GA. SECURITYGRILLE (13/16" HOLESON 1" CTRS.)

1/16" (2mm)

(INCLUDED)TWO SIDESGLAZING TAPE

SL-FS-LSC is not fire rated.

SECURITY CAM LOCKWITH KEY

PULL HANDLE

FRAMEDSTAINLESS

STEELSCREEN


GRILLE

INSTALLATION: By drilling 1/4" (6mm) holes thru the door, around the perimeter of the door cutout. Vision frame has countersunk mounting holes for #8x32 Pinned Torx security screw thru bolts with a blank head on one side for flush appearance.

PINNED TORX SECURITY THRU BOLT

DETAIL DRAWING

TECHNICAL DATAFROM


FIRE RATINGS



SL-FS-LSCMETAL VISION FRAME

WITHSTAINLESS STEEL SCREEN

ANDSECURITY GRILLE TWO SIDES

PLUS LOCKINGSECURITY COVER

NOT FIRE RATED




IMPORTANT: Interpretation of building and fire codes may vary. Consult with the local authority having jurisdiction in your area, to determine appropriate standards.



12 GA. SECURITYGRILLE (13/16" HOLESON 1" CTRS.)3/16"

(5mm)

(21mm)13/16"

(32mm)

(6mm)(6mm)

GLAZING TAPE: Framed screen is held in place with glazing tape on both sides, sandwiched between the security grilles using 1/16" (1.6mm)thick, closed cell polyvinyl chloride foam tape sealant with pressure sensitive adhesive two sides.

USES: For use where ventilation is required, but security on one or both sides of the screen is necessary, i.e. kitchen doors in schools or restaurants.

FRAMEDSTAINLESSSTEEL SCREEN

)( Grille on one side onlyAlso available with Security

OR OTHER(44mm)

1/4" 1/4"1 3/4"

THICKNESSOVER SCREEN1/16" (2mm)GLAZING SPACE

OUTSIDEINSIDE

O.D.FRAME

ORDE

R SIZE

PLUS

1 1/2

" (38m

m)SIZE

SCREEN

ORDE

R SIZE

MINU

S 1/4"

(6mm

)

3/8" (10mm)

1 1/4"

LITEVISIBLE

ORDE

R SIZE

MINU

S 1" (2

5mm)

MATERIAL: Frame is 18 GA (1.25mm) CRS with 12 GA ( 2.5mm) CRS Security Grille two sides, 13/16" (21mm) square holes on 1" (25mm) centers welded to each side of vision frame.


DOOR THICKNESS: Specified by customer, 1 3/4" (44mm) is standard.


SPECIALS: Fractional Sizes, Security cover, Gauge.FASTENERS: Special Security Screw Fasteners. See page 26, this section.

supplied). Plated Finishes to match the lock, hinges and closer.FINISH: Custom Baked Enamel Colors (as per sample chip

(Hot Dipped or Zinc Plated). Not available in Galvanized Coil.MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized

CUTOUTDOOR

&SIZE

ORDER

1/16" (2mm)

(INCLUDED)TWO SIDESGLAZING TAPE

SL-FS is not fire rated.

FRAMEDSTAINLESS

STEELSCREEN

12 GA. SECURITYGRILLE

INSTALLATION: By drilling 1/4" (6mm) holes thru the door, around the perimeter of the door cutout. Vision frame has countersunk mounting holes for #8x32 one way vandal proof security screw thru bolts with a blank head on one side for flush appearance.

SCREEN: Framed screen incorporates #304 stainless steel screen wire, .009" (.228mm) thick, using a 18-18 mesh to restrict penetration from insects. Screen material is installed into a .020" (.508mm) thick mill finished aluminum frame.

DETAIL DRAWING

TECHNICAL DATAFROM


FIRE RATINGS



SL-FSMETAL VISION FRAME

WITHSTAINLESS STEEL SCREEN

ANDSECURITY GRILLE TWO SIDES

NOT FIRE RATED






#8X32 THRU BOLT, BLANK ONE ENDUSED FOR ALL MODELS: SG-10, SG-12, SL-IS, FGS, PLSL AND BR-7

*Screwdrivers and insert bits for Security Fasteners are available.Consult Factory for Price and Availability.

ONE WAY VANDALPROOF SECURITY SCREW#8X1" USED FOR: DSFP, FLDL-UL-SG1, FLDL-UL-SG2#8X3/4" USED FOR: SG-10-SSD, SSD#8X1-3/4" USED FOR: LoPro-SC, LoPro-GR, LoPro-SC-GR, LoPro-SSD

3/8"

STANDARD

NOTCHED SPANNERHEAD SCREW

TORX-PLUS FLAT HEADSECURITY SCREW

(Available on all Security Products)

SECURITY SCREWTORX FLAT HEAD SOCKET

SNAKE EYE SPANNERFLAT HEAD SECURITY SCREW(DRILLED SPANNER)

PINNED FLAT HEAD CAP SCREW(TAMPER RESISTANT HEX SOCKET)

ONLY AVAILABLE ONCERTAIN APPLICATIONS

OPTIONAL SECURITY FASTENERS*

1/4"X20 THRU BOLT BLANK ONE END-MEETS ASTM F-1450-97 (MUST SPECIFY): SG-10, BR-7, SG-12-SP, SG-10-SP, SG-12-LSC

TECHNICAL DATAFROM

DETAIL DRAWING

FASTENERSFOR

SECURITY VISION FRAMESAND

SECURITY DOOR LOUVERS

Documents

Tech Data Security Vision Frames - AnemostatSecurity Sliding Door Panel ... HIGH SECURITY METAL VISION FRAME FOR SPECIAL GLASS OR DOOR THICKNESS ... 12 GA. (2.8mm) cold rolled steel