Embed Size (px)
Citation preview
ECO Technical documentation 2017 Export
TECHNICAL INFORMATIONHENRAD PREMIUM ECO RADIATOR YOUR IDEAL HEATING SOLUTION
ECO RANGE
TRANSPORT
31.3%INDUSTRY
28.3%
BUILDINGS
40.4%85% Heating & hot water 15% Electricity
ENERGY CONSUMPTION
3
WE CAN NO LONGER DENY IT: THE ENVIRONMENT IS SUFFERING BECAUSE OF OUR ENERGY CONSUMPTION.
WHY Green heat?
We are all looking for SMARTER WAYS TO MANAGE ENERGY. Buildings are big consumers of energy and the majority of that consumption is for heating and hot water, so our sector has a great responsibility to innovate. With renewable energy and effi cient heating and cooling technologies, OUR BUILDINGS CAN EMIT UP TO 60% LESS CO2.
The European Union helps carry the load by gradually making energy consumption standards stricter. And rightly so, because with a perfect energy balance, a modern house uses less than a tenth of what was possible 30 years ago.
Modern heating technologies and renewable energy are crucially important in order to achieve the ambitious objectives. To get the full benefi ts, such technologies need low temperature systems. That’s where the green heat of Henrad ECO radiators comes in.
Source: “Green Paper on Energy Effi ciency or Doing More with Less” (March 2006).
VALVE CAN BE FITTED ON THE LEFT OR THE RIGHT, QUICK CONNECTION, FEELING OF COMFORT MAINTAINED IN LOW TEMPERATURE SYSTEMS, SUITABLE FOR RENEWABLE ENERGY. REASON ENOUGH TO CHOOSE HEAT THAT IS GREEN.
SAVE ON YOUR ENERGY BILLS WITH THE Henrad Premium ECO
UP TO 10.5%
Faster heat up process
UP TO 23%
Reduced energy bills
UP TO 50%
A decrease in energy loss through reduced radiation from the back panel
UP TO 8.8%
More radiant heat
UP TO 53%
Pre-set thermostatic valve means savings
UP TO 6%
Higher mean surface temperature on the front panel
www.isso.nl/werkvelden/energie-milieu/epa/gelijkwaardigheidsverklaringen
Quality verifi ed and certifi catied by ISSO
ISSOCERTIFIED
ECO RADIATOR * TRADITIONAL RADIATOR *
After 8 minutes at a mass fl ow of 50%
After 8 minutes at a nominal mass fl ow
After 8 minutes at a mass fl ow of 50%
After 8 minutes at a nominal mass fl ow
5
The HEAT TRANSFER from a traditional radiator is usually 80% by convection and 20% by radiation. The comfortable feeling of warmth from solar radiation is therefore less present in a traditional radiator, but the ECO radiator changes that.
The photos below show that the heat transfer by radiation increases signifi cantly in the ECO radiator. Especially the greater amount of radiation from the front panel is considered very pleasant.
With CONVECTION HEAT, the air in a room is heated as air fl ows pass over heating elements. The heated air rises, cools and falls again down the walls. The cooled air is then warmed up again by the heating system.
In RADIANT HEAT, infra-red radiation is emitted to heat objects in the room directly, independently of air fl ows such as wind or draughts. Radiant heat gives the entire room including furniture, walls and people, a completely even temperature. These objects in turn yield their heat to the room, making it feel very comfortable. The best example of radiant heat is the sun. Standing in the sun, you feel the radiation on your skin, which immediately makes you feel warmer, even if the nearby ambient air in the shade is not cooler than the air directly in the sun. The only difference felt is the radiant heat.
These measurements show that, at a nominal mass fl ow of 50% (good for more than 90% of the nominal emission of heat), the radiation capacity of the Type 21 and Type 22 ECO radiators increase by a factor of 1.5 compared with a traditional radiator.
* Test conditions: radiator type 22 (height = 600 mm, length = 1,000 mm) at 70/55/20°C.
HEAT CAN BE TRANSFERRED IN DIFFERENT WAYS: THROUGH CONDUCTION, CONVECTION OR RADIATION. HOMES ARE HEATED MAINLY BY CONVECTION AND/OR RADIANT HEAT.
MORE RADIATION =More comfort + lower costs!
DEPENDING ON TYPE AND HEIGHT, THE ECO RADIATOR EMITS UP TO 50% MORE RADIANT HEAT.
63.0
62.5
62.0
61.5
61.0
60.5
60.0
59.5
59.0
58
53
48
43
38
33
28
23
18
60 860 10120 12180
+ 4%
+ 53%
+ 40%
TIME minutesTIME seconds
TEMPERATURE°CTEMPERATURE°C
— ECO radiator— Traditional radiator
— ECO radiator— Traditional radiator
IN THIS WAY, ECO RADIATORS YIELD AN ENERGY SAVING OF AT LEAST 6%, WITHOUT REDUCING THE PERCEIVED TEMPERATURE.
AN ECO RADIATOR REACHES A SURFACE TEMPERATURE ON THE FRONT PANEL THAT IS UP TO 54% HIGHER AFTER 2 MINUTES AND A HIGHER FINAL TEMPERATURE UNDER FULL LOAD, THEREBY EMITTING UP TO 50% MORE RADIANT HEAT.
The increased radiant heat is a direct consequence of the increased mean surface temperature of the front panel. An external test laboratory performed exhaustive tests on the ECO radiators, with the results shown below.
The front panel of the ECO radiator has a mean temperature of 43°C after 2 minutes and 50°C after 3 minutes.At the same times, the front panel of a traditional radiator has mean temperatures of 28°C and 35.7°C respectively.
Just like with the sun, the perceived temperature with the ECO radiator is higher than with a traditional radiator. In other words, at a constant perceived temperature of 20°C, the increased radiant heat from the ECO radiator allows the thermostat to be a few degrees lower.*
According to the EN 12831 Standard, in practice there are only a few days in a year (on average ten) on which radiators use their maximum heat emission for a longer period of time. ECO radiators provide additional benefits even during these limited number of days of prolonged full load.
After the ECO radiator has stabilised (i.e. is in full load), its front panel is up to 4% warmer than a traditional radiator.
* According to the BDH (Bundesindustrieverband Deutschland), setting your thermostat a few degrees lower means an energy saving of 6%.
63.0
62.5
62.0
61.5
61.0
60.5
60.0
59.5
59.0
6 8 10 12
-23%
TIME minutes
TEMPERATURE°C
— ECO radiator— Traditional radiator
FRONT
BACK
7
IN ADDITION TO MORE RADIANT HEAT AND THE HIGHER MEAN TEMPERATURE OF THE FRONT PANEL, THERE ARE VARIOUS FACTORS THAT REDUCE THE ENERGY BILL CONSIDERABLY IF YOU CHOOSE AN ECO RADIATOR.
FASTER HEATING-UP PROCESSLess CO2
THE ECO RADIATOR’S FRONT PANEL REACHES ITS MAXIMUM TEMPERATURE UP TO 23% FASTER THAN THAT OF A TRADITIONAL RADIATOR. IN OTHER WORDS: THE ECO RADIATOR’S FRONT PANEL IS ALREADY AT ITS MAXIMUM TEMPERATURE WHILE A TRADITIONAL RADIATOR STILL NEEDS A LONG TIME TO WARM UP.
Thanks to its unique fl ow pattern, the ECO radiator’s HEATING-UP TIME is signifi cantly shorter than that of a traditional radiator.
The DIRECT FLOW of water into the upward channel in the front panel. In a traditional radiator, the hot water fi rst has to go through a series of rising channels before it is spread over the front and back panels.
The further DISTRIBUTION of the hot water: the hot water is spread evenly across the other channels of the front panel. A unique system then takes it to the back panel, where it is also spread over all the water channels.
The front panel of the ECO radiator reaches its maximum temperature of 62.5°C after 8.5 minutes. At that moment, the front panel of a traditional radiator is at only 59.3°C and its maximum temperature is only reached after 11 minutes, by which time the ECO radiator will have already been at its maximum temperature for over 2.5 minutes.
* Test conditions: type 22 radiator (height = 600 mm, length = 1,000 mm) at 70/55/20°C.
63
58
53
48
43
38
33
28
23
18
63
62
61
60
59
58
57
56
55
54
60 60 120 240180 300 360 420 8 10 12 14 16
+12%
-7%
-26,7%
-21,7%
-16,4%
TIME minutesTIME seconds
TEMPERATURE°CTEMPERATURE°C
— ECO radiator back— Traditional radiator back
— ECO radiator front— Traditional radiator front
— ECO radiator back— Traditional radiator back
9
BY FURTHER LIMITING ENERGY LOSSES, THE ECO RADIATOR SUCCEEDS IN INCREASING THE EFFICIENCY OF THE HEATING SYSTEM EVEN MORE.
FEWER LOSSESHigher effi ciency!
Not only is the front panel hotter during the entire heating-up process, even after stabilisation, but the BACK PANEL IS COLDER, which is just as important. Because the back panel usually faces an outside wall, there is a possible loss of radiation through the wall.
The graph below shows the mean temperature of the back panel at specifi c moments during the heating-up process.
After 180 seconds, the mean temperature of the ECO radiator’s back panel is 25.6°C, whereas a traditional radiator’s is already 35°C.
The ECO radiator’s values after 5 and 7 minutes are 37.6°C and 47.8°Crespectively, whereas the results for a traditional radiator are 48.1°C and 57.2°C.
The graph below shows the situation for both radiators after the heating system has stabilised.
THERE IS STILL A SIGNIFICANT DIFFERENCE BETWEEN THE MEAN TEMPERATURES OF THE BACK PANELS OF THE TWO TYPES OF RADIATOR AFTER STABILISATION. THE TEMPERATURE OF THE ECO RADIATOR’S BACK PANEL IS UP TO 7% LOWER COMPARED WITH THAT OF A TRADITIONAL RADIATOR.
TRADITIONAL RADIATOR ECO RADIATOR
In a traditional radiator, there is hardly any difference in temperature between the front and back panels. The radiant heat is emitted to the wall, and in the case of an outside wall, this heat is lost through it and energy loss occurs.
IN THE CASE OF THE ECO RADIATOR, THERE IS A WIDE DIFFERENCE IN TEMPERATURE BETWEEN THE TWO PANELS, WHICH CAN INCREASE TO OVER 12%.
110
100
90
80
70
60
50
40
30
20
10
0
0 50 100 150 200
PERCENTAGE HEAT OUTPUT COMPARED WITH NORMAL OUTPUT %
MASS THROUGHPUT COMPARED WITH NORMAL MASS THROUGHPUT %
11
THE THERMOSTATIC VALVE IS FACTORY-SET IN THE ECO RADIATOR IN RELATION TO THE SIZE OF THE RADIATOR, WHICH ENSURES OPTIMAL OUTPUT AND EFFICIENCY.
PRE-SETThermostatic valve
In practice, OPTIMAL HYDRAULIC SETTING OF THE HEATING INSTALLATION is very important, certainly in view of rising energy costs.
The planner or architect uses software to correctly calculate all the necessary parameters (mass fl ows or throughput, couplers and connectors, valve settings, etc.) for the hydraulic settings of the installation in new-build housing, which are then implemented by the installer.
A lot of this information gets lost as time passes, and adjustments and/or repairs made in the meantime make fi nding the correct settings in the event of restoration more complicated.
A more PRACTICALLY-ORIENTED SOLUTION is to fi t the
radiators with a Kv pre-set valve in the factory. The principle is relatively simple: the valve ensures that at a given pressure difference the correct quantity of hot water or mass fl ow passes through the radiator.
The PROPER PRE-SETTING OF THE VALVE means that the radiator’s heat output is close to its nominal value. The valves in the ECO radiator are set so that the throughput in the radiator is equal to or a little higher than the nominal throughput. A minimum of extra throughput gives the heating system suffi cient or a little more power, and the situation is brought close to its nominal or ideal state.
Increasing the throughput even more, which happens with an unregulated valve, gives relatively little extra power. This could cause other radiators to get insuffi cient hot water and therefore be unable to heat the room.
Factory pre-setting is possible because radiator dimensions do not differ infi nitely. To be certain that small radiators with a low heat output and limited water content can be adjusted optimally, HENRAD HAS DECIDED TO USE TWO TYPES OF VALVE:• a fi ne adjustment valve (Heimeier 4369 with a yellow top)
especially for small radiators• a standard valve (Heimeier 4368) with 4 different pre-sets
(white, red, black and blue) for normal to large radiators
HENRAD VALVE OTHER VALVE
Reference 4369 4368 4368 4368 4368
Colour yellow white red black blue
Pre-set value 5.5 2.5 4.5 6 8
KV (at 1K) pre-set to 0.105 0.215 0.305 0.37 0.40
Adjustment range (at 1K) 0.05 – 0.14 0.12 – 0.40
At Henrad, the KV SETTING OF RADIATORS IS SHOWN UNEQUIVOCALLY AND BY THE COLOUR:
Furthermore, Henrad valves are continuously adjustable (with tapered groove), which means that the mass fl ow can be controlled very accurately and there is less sensitivity to faults. This is in contrast to other valves that are diffi cult or impossible to align accurately and can become clogged because of impurities (such as chalk) in the water, which leads to their working poorly and to insuffi cient heating of the radiator.
The benefi ts of pre-setting are considerable:• time-saving during installation.• optimal water throughput in the radiator.• higher system effi ciency as a result of lower return temperatures.
The BDH (Bundesindustrieverband Deutschland) has shown that factory pre-set valves have an extremely favourable effect on the hydraulic balance of a heating installation.
THIS GIVES ENERGY SAVINGS OF UP TO 6% COMPARED WITH NON-BALANCED SYSTEMS.
Furthermore, if pump consumption is taken into account, then a heating system with factory pre-set valves can give additional savings of up to 20% in the electricity the pump uses.
PREMIUM ECOHEIGHT 300 400 500 600 700 900
TYPE 11 21 22 33 11 21 22 33 11 21 22 33 11 21 22 33 11 21 22 33 11 21 22 33400 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 2.5 5.5 5.5 5.5 2.5 5.5 5.5 2.5 2.5 5.5 2.5 2.5 2.5500 5.5 5.5 5.5 5.5 5.5 5.5 5.5 2.5 5.5 5.5 5.5 2.5 5.5 5.5 2.5 2.5 5.5 2.5 2.5 2.5 5.5 2.5 2.5 4.5600 5.5 5.5 5.5 2.5 5.5 5.5 5.5 2.5 5.5 5.5 2.5 2.5 5.5 2.5 2.5 2.5 5.5 2.5 2.5 4.5 2.5 2.5 2.5 4.5700 5.5 5.5 5.5 2.5 5.5 5.5 2.5 2.5 5.5 2.5 2.5 2.5 5.5 2.5 2.5 4.5 2.5 2.5 2.5 4.5 2.5 2.5 4.5 6800 5.5 5.5 2.5 2.5 5.5 2.5 2.5 2.5 5.5 2.5 2.5 4.5 2.5 2.5 2.5 4.5 2.5 2.5 2.5 4.5 2.5 2.5 4.5 6900 5.5 5.5 2.5 2.5 5.5 2.5 2.5 2.5 2.5 2.5 2.5 4.5 2.5 2.5 2.5 4.5 2.5 2.5 4.5 6 2.5 4.5 4.5 8
1,000 5.5 2.5 2.5 2.5 5.5 2.5 2.5 4.5 2.5 2.5 2.5 4.5 2.5 2.5 4.5 6 2.5 2.5 4.5 8 2.5 4.5 6 81,100 5.5 2.5 2.5 2.5 2.5 2.5 2.5 4.5 2.5 2.5 4.5 6 2.5 2.5 4.5 6 2.5 4.5 4.5 8 2.5 4.5 6 81,200 5.5 2.5 2.5 4.5 2.5 2.5 2.5 4.5 2.5 2.5 4.5 6 2.5 4.5 4.5 8 2.5 4.5 6 8 4.5 6 8 81,400 5.5 2.5 2.5 4.5 2.5 2.5 4.5 6 2.5 4.5 4.5 8 2.5 4.5 6 8 4.5 4.5 8 8 4.5 8 8 81,600 2.5 2.5 6 2.5 2.5 4.5 8 2.5 4.5 6 8 4.5 4.5 8 8 4.5 6 8 8 6 8 8 81,800 2.5 4.5 6 2.5 4.5 4.5 8 2.5 4.5 6 8 4.5 6 8 8 4.5 8 8 8 6 8 8 82,000 2.5 4.5 8 2.5 4.5 6 8 4.5 6 8 8 4.5 8 8 8 6 8 8 8 8 8 8 82,200 4.5 4.5 8 4.5 8 8 4.5 6 8 8 6 8 8 82,400 4.5 6 8 6 8 8 4.5 8 8 8 6 8 8 82,600 6 8 8 8 82,800 8 8 8 8 83,000 8 8 8 8 8
Art. 4369 Art. 4368 Art. 4368 Art. 4368 Art. 4368pre-set 5.5 pre-set 2.5 pre-set 4.5 pre-set 6 pre-set 8
HYGIENE ECOHEIGHT 300 400 500 600 700 900
TYPE 10 20 30 10 20 30 10 20 30 10 20 30 10 20 30 10 20 30400 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 2.5500 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 2.5 5.5 5.5 2.5 5.5 2.5 2.5600 5.5 5.5 5.5 5.5 5.5 5.5 5.5 5.5 2.5 5.5 5.5 2.5 5.5 5.5 2.5 5.5 2.5 2.5700 5.5 5.5 5.5 5.5 5.5 2.5 5.5 5.5 2.5 5.5 5.5 2.5 5.5 2.5 2.5 5.5 2.5 2.5800 5.5 5.5 5.5 5.5 5.5 2.5 5.5 5.5 2.5 5.5 2.5 2.5 5.5 2.5 2.5 5.5 2.5 4.5900 5.5 5.5 2.5 5.5 5.5 2.5 5.5 2.5 2.5 5.5 2.5 2.5 5.5 2.5 2.5 2.5 2.5 4.5
1,000 5.5 5.5 2.5 5.5 2.5 2.5 5.5 2.5 2.5 5.5 2.5 2.5 5.5 2.5 4.5 2.5 2.5 4.51,100 5.5 5.5 2.5 5.5 2.5 2.5 5.5 2.5 2.5 5.5 2.5 4.5 2.5 2.5 4.5 2.5 4.5 61,200 5.5 5.5 2.5 5.5 2.5 2.5 5.5 2.5 4.5 2.5 2.5 4.5 2.5 2.5 4.5 2.5 4.5 61,400 5.5 2.5 2.5 5.5 2.5 2.5 2.5 4.5 2.5 2.5 4.5 2.5 4.5 6 2.5 4.5 81,600 2.5 2.5 5.5 2.5 4.5 2.5 4.5 2.5 4.5 6 2.5 4.5 8 2.5 6 81,800 2.5 4.5 2.5 2.5 4.5 2.5 6 2.5 4.5 8 2.5 4.5 8 4.5 8 82,000 2.5 4.5 2.5 2.5 6 2.5 4.5 8 2.5 4.5 8 2.5 6 8 4.5 8 82,200 2.5 4.5 4.5 6 2.5 4.5 8 2.5 6 82,400 2.5 4.5 4.5 8 2.5 4.5 8 2.5 6 82,600 4.5 6 4.5 6 82,800 4.5 6 4.5 6 83,000 4.5 8 6 8 8
13
The factory settings of the pre-installed thermostatic valves were determined on the basis of the following preconditions:• heat output at 70/55/20°C ( ∆t = 15°C ).• differential pressure ∆p = 100 mbar.• control difference 1K.
In case of abnormal preconditions, the valve can be adjusted manually and precisely (or be replaced if necessary) through the pre-setting tables 4368 and 4369 (with setting key art. T1622). In one-pipe systems the valve should be adjusted to position 8.
FACTORY PRE-SETTING
MAX. 1K CONTROL DIFFERENCE
Radiator performanceQ [W] 20
0
250
300
400
500
600
700
800
900
1,00
0
1,20
0
1,40
0
1,60
0
1,80
0
2,00
0
2,20
0
2,40
0
2,60
0
2,80
0
3,00
0
3,20
0
3,40
0
3,60
0
3,80
0
4,00
0
4,80
0
5,30
0
6,50
0
6,80
0
7,20
0
∆t [K] ∆p [mbar] Setting range10 50 4 5 7
100 2 3 5 6 8150 1 2 3 5 7 8
15 50 2 3 4 6 8100 1 1 2 4 5 6 8150 1 1 1 2 4 5 6 7 8
20 50 1 1 2 4 5 7 8100 1 1 1 2 3 5 5 6 8 8150 1 1 1 1 2 3 4 5 5 7 8
40 50 1 1 1 1 2 3 4 5 5 7 8100 1 1 1 1 1 2 3 3 5 5 6 8 8150 1 1 1 1 1 1 2 3 4 5 5 7 8 8
MAX. 2K CONTROL DIFFERENCE
Radiator performanceQ [W] 20
0
250
300
400
500
600
700
800
900
1,00
0
1,20
0
1,40
0
1,60
0
1,80
0
2,00
0
2,20
0
2,40
0
2,60
0
2,80
0
3,00
0
3,20
0
3,40
0
3,60
0
3,80
0
4,00
0
4,80
0
5,30
0
6,50
0
6,80
0
7,20
0
∆t [K] ∆p [mbar] Setting range10 50 3 5 6 7 8 8
100 1 3 4 5 6 7 8 8 8150 1 1 3 4 6 6 7 7 8 8
15 50 1 3 3 5 6 7 7 8 8 8100 1 1 1 3 5 5 6 6 7 8 8 8150 1 1 1 1 3 4 5 6 6 6 7 8 8
20 50 1 1 1 3 5 6 6 7 7 8 8100 1 1 1 1 3 4 5 5 6 6 7 8 8 8150 1 1 1 1 3 3 4 5 6 6 7 7 8 8 8
40 50 1 1 1 1 1 3 3 4 5 6 6 7 7 8 8 8 8100 1 1 1 1 1 3 3 4 5 5 6 6 6 7 7 8 8 8 8 8 8150 1 1 1 1 1 1 3 3 4 5 6 6 6 6 7 7 7 8 8 8 8
Q = Heat output ∆p = Differential pressure ∆t = Target: setting range 100 mbar = 10 kPa = 1mWS
MANUAL BALANCINGExampleVALVE 4369
5.5
EXAMPLE
Target: setting rangeGiven: Premium ECO: Type 11 - Height 900 - Length 500 needs to operate at: 80/70/20°C, differential pressure: ∆t = 50mbar • pre-assembled valve: yellow 4369 - pre-setting value: 5.5 • emission at 80/70/20°C: 790 Watt ∆t = 10°C (80-70°C) • according to the above table: P-band 1K (upper table): no setting possible. P-band 2K (lower table): no setting possible.Solution: pre-setting value according to table 4369: none (blank box) • yellow valve 4369 must be replaced by white, red, black or bleu valve 4368 and readjusted at: P-band 1K: readjust at position “5” P-band 2K: readjust at position “3”
5.5
4369
3
4368
MAX. 1K CONTROL DIFFERENCE
Radiator performanceQ [W] 20
0
250
300
400
500
600
700
800
900
1,00
0
1,20
0
1,40
0
1,60
0
1,80
0
2,00
0
2,20
0
2,40
0
2,60
0
2,80
0
3,00
0
3,20
0
3,40
0
3,60
0
3,80
0
4,00
0
4,80
0
5,30
0
6,50
0
6,80
0
7,20
0
∆t [K] ∆p [mbar] Setting range10 50 1 1 1 2 3 3 4 5 6 7
100 1 1 1 1 2 2 3 3 4 4 5 7150 1 1 1 1 2 2 2 3 3 4 5 6 8
15 50 1 1 1 1 2 2 2 3 3 4 5 6100 1 1 1 1 2 2 2 2 3 4 5 5 6 8150 1 1 1 1 1 2 2 2 3 3 4 5 5 6 7
20 50 1 1 1 1 2 2 2 3 3 4 5 6 7100 1 1 1 1 1 2 2 2 3 3 4 4 5 5 6 7150 1 1 1 1 1 1 2 2 2 3 3 4 4 5 5 6 6 7 8
40 50 1 1 1 1 1 1 2 2 2 3 3 3 4 4 5 5 5 6 6 7100 1 1 1 1 1 1 2 2 2 2 2 3 3 3 3 4 4 4 5 6150 1 1 1 1 1 1 1 2 2 2 2 2 2 2 3 3 3 4 5 6 7 8
MAX. 2K CONTROL DIFFERENCE
Radiator performanceQ [W] 20
0
250
300
400
500
600
700
800
900
1,00
0
1,20
0
1,40
0
1,60
0
1,80
0
2,00
0
2,20
0
2,40
0
2,60
0
2,80
0
3,00
0
3,20
0
3,40
0
3,60
0
3,80
0
4,00
0
4,80
0
5,30
0
6,50
0
6,80
0
7,20
0
∆t [K] ∆p [mbar] Setting range10 50 1 1 1 2 2 3 3 3 4 5 5 6 7 8
100 1 1 1 1 2 2 2 2 3 3 4 5 5 6 6 7 7 8150 1 1 1 1 2 2 2 2 3 3 4 4 5 5 6 6 7 7 8 8
15 50 1 1 1 1 2 2 2 3 3 3 4 5 5 6 6 7 8 8100 1 1 1 1 1 2 2 2 2 3 3 4 4 5 5 6 6 6 7 7 7 8 8150 1 1 1 1 1 2 2 2 2 3 3 3 4 4 5 5 5 6 6 6 6 7 8
20 50 1 1 1 1 2 2 2 2 3 3 3 4 5 5 5 6 6 7 7 7 8 8100 1 1 1 1 1 1 2 2 2 2 3 3 3 4 4 5 5 5 5 6 6 6 7 8150 1 1 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 6 7 8
40 50 1 1 1 1 1 1 2 2 2 2 2 3 3 3 3 3 4 4 4 5 5 6 7 7 8100 1 1 1 1 1 1 1 2 2 2 2 2 2 2 3 3 3 3 4 4 5 5 6150 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 3 3 3 4 4 5
Q = Heat output ∆p = Differential pressure ∆t = Target: setting range 100 mbar = 10 kPa = 1mWS
15
MANUAL BALANCINGExampleVALVES 4368
2.5 84.5 6
EXAMPLE
Target: setting rangeGiven: Premium ECO: Type 22 - Height 500 - Length 1,400 needs to operate at: 60/40/20°C, differential pressure: ∆t = 50mbar • pre-assembled valve: red 4368 - pre-setting value: 4.5 • emission at 60/40/20°C 1,008 Watt ∆t = 20°C (60-40°C) Solution: pre-setting value according to table 4368: • P-band 1K: readjust at position “3” • P-band 2K: readjust at position “2”
4.5
4368
2
4368
5.5
Q 350 c x ∆t 1.163 x 15
Valve radiators without fi ttingThermostatic valve body with thermostatic head
PRE-SETTINGThermostatic valve body
Max. opera-ting temp.
Max. opera-ting pressure
Permitted differential pressure, during which the valve is kept closed ∆p [bar]
TB*[°C]
PB[bar]
Thermostatic head
EMO T/NCEMOtec/NC
EMO 1/3EMO EIB/LON
EMO T/NOEMOtec/NO
1 2 3 4 5 6 7 8
p-band xp 1.0 K Kv value [m3/h] 0.05 0.06 0.07 0.08 0.10 0.11 0.12 0.14
120 10 4.0 2.7 3.5p-band xp 2.0 K Kv value [m3/h] 0.06 0.06 0.08 0.09 0.11 0.15 0.18 0.26
Kv value [m3/h] 0.06 0.07 0.08 0.10 0.12 0.17 0.25 0.50
Flow tolerance ± [%] 42 42 37 36 35 32 30 10
* With protection cap or actuator 100°C
2 3 5 10 20 30 50 100 200 300 500 2 3 5 10 20 30 50 100 200 300 500
30
20
10
5
3
2
1
0.5
0.3
0.2
0.1
30
20
10
5
3
2
1
0.5
0.3
0.2
0.1
300
200
100
50
30
20
10
5
3
2
1
300
200
100
50
30
20
10
5
3
2
1DIFF
EREN
TIAL
PRE
SSUR
E ∆P
[KPA
]
PRE-SETTING 1 2 3 4 5 6 7 8
DIFF
EREN
TIAL
PRE
SSUR
E ∆P
[MBA
R]
DIFF
EREN
TIAL
PRE
SSUR
E ∆P
[KPA
]
PRE-SETTING 1 2 3 4 5 6 7 8
DIFF
EREN
TIAL
PRE
SSUR
E [M
BAR]
Information received from Heimeier
P-BAND [XP] 1.0 K P-BAND [XP] 2.0 K
PRESSURE DROP DIAGRAMValve with integrated precision pre-setting (Art. 4369)
VALVE RADIATORS WITHOUT CONNECTION FITTINGS.
SAMPLE CALCULATION
Target: setting rangeGiven: • heat fl ow: Q = 350 Watt • temperature spread: ∆t = 15 K (65-50°C) • pressure loss, valve radiator: ∆pV = 32 mbarSolution: mass fl ow: m = = = 20 kg/h
Setting range from diagram • with P-band 1.0 K: 6 • with P-band 2.0 K: 4
2.5 84.5 6
Q 1,135 c x ∆t 1.163 x 15
Valve radiators without fi ttingThermostatic valve body with thermostatic head
PRE-SETTINGThermostatic valve body
Max. opera-ting temp.
Max. opera-ting pressure
Permitted differential pressure, during which the valve is kept closed ∆p [bar]
TB*[°C]
PB[bar]
Thermostatic head
EMO T/NCEMOtec/NC
EMO 1/3EMO EIB/LON
EMO T/NOEMOtec/NO
1 2 3 4 5 6 7 8
p-band xp 1.0 K Kv value [m3/h] 0.12 0.19 0.24 0.28 0.33 0.37 0.39 0.40
120 10 4.0 2.7 3.5p-band xp 2.0 K Kv value [m3/h] 0.13 0.22 0.31 0.38 0.47 0.57 0.66 0.75
Kv value [m3/h] 0.16 0.27 0.38 0.43 0.65 0.98 1.23 1.43Flow tolerance ± [%] 40 30 25 23 17 15 12 10
* With protection cap or actuator 100°C
Information received from Heimeier
P-BAND [XP] 1.0 K P-BAND [XP] 2.0 K
2 3 5 10 20 30 50 100 200 300 500 2 3 5 10 20 30 50 100 200 300 500
30
20
10
5
3
2
1
0.5
0.3
0.2
0.1
30
20
10
5
3
2
1
0.5
0.3
0.2
0.1
300
200
100
50
30
20
10
5
3
2
1DIFF
EREN
TIAL
PRE
SSUR
E ∆P
[KPA
]
DIFF
EREN
TIAL
PRE
SSUR
E ∆P
[MBA
R]
DIFF
EREN
TIAL
PRE
SSUR
E ∆P
[KPA
]
DIFF
EREN
TIAL
PRE
SSUR
E ∆P
[MBA
R]
300
200
100
50
30
20
10
5
3
2
1
PRE-SETTING 1 2 3 4 5 6 7 8PRE-SETTING 1 2 3 4 5 67
8
17
PRESSURE DROP DIAGRAMStandard valve (Art. 4368)
VALVE RADIATORS WITHOUT CONNECTION FITTINGS.
SAMPLE CALCULATION
Target: setting rangeGiven: • heat fl ow: Q = 1,135 Watt • temperature spread: ∆t = 15 K (65-50°C) • pressure loss, valve radiator: ∆pV = 30 mbarSolution: mass fl ow: m = = = 65 kg/h
Setting range from diagram • with P-band 1.0 K: 6 • with P-band 2.0 K: 4
THE ECO RADIATOR CAN BE COMBINED PERFECTLY WITH ALL TYPES OF LOW-TEMPERATURE SYSTEMS SUCH AS HEAT PUMPS, SOLAR PANELS AND BIOMASS INSTALLATIONS.
MORE SUITABLE FORRenewable energy!
Considering the limited number of days a year that a radiator has to operate at MAXIMUM HEAT OUTPUT, partial heating with a mass fl ow of 10-30% will be suffi cient to heat a room during 90 to 95% of the heating periods. The radiator’s mean surface temperature will be lower during these periods.
The desired room temperature will be achieved by a traditional radiator with a surface temperature of less than 40°C, but it will not feel as comfortable. Thanks to its serial fl ow, the ECO radiator has a higher front panel temperature, which gives off up to 50% MORE RADIANT HEAT.
It is precisely this increased radiation that maintains a comfortable feeling, even at lower mass fl ows. This is extra important when replacing an obsolete heating system that operates at high temperature with a modern system that operates at a lower temperature and uses renewable energy sources such as heat pumps or solar panels.
ECO radiators are therefore PERFECT FOR USE IN HEATING INSTALLATIONS THAT HAVE BEEN CONVERTED FROM A HIGH-TEMPERATURE SYSTEM TO A LOW-TEMPERATURE SYSTEM such as heat pumps.
19
OTHER BENEFITS!
VALVE CAN BE FITTED ON THE LEFT OR THE RIGHT The valve can be fi tted on the left or the right of the ECO radiator without having to adapt the return pipe. No separate part numbers, no separate stock, no extra price for a left-hand version, and yet still the same short delivery time as for a radiator with the valve on the right.
CENTRE CONNECTION There is a ¾” conical male Euroconus connection in the middle of
the ECO radiator. This means that the location of the connection no longer depends on the length of the radiator, with the benefi t
that pipes can be installed at an early stage of the project without having to know the size of the radiator. There is also an
additional ½” female connection underneath at the right.
CONNECTION FACILITIES FOR RENOVATION AS WELL AS NEW CONSTRUCTION
This ECO radiator has an additional ½” female connection underneath at the right specifi cally for the renovation market.
This is in addition to the ¾” conical male Euroconus centre connection that is often used in new construction projects.
INPUT ALWAYS ON THE LEFT The input on all multi-panel ECO radiators (T21, T22 and T33) has to be connected on the left, irrespective of whether the valve is fi tted on the left or on the right.
EASIER TESTING Using our installation template enables the heating installation and the pipes to be fully tested without the radiators having to be in place.
QUICK CONNECTION The ¾” conical male Euroconus centre connection allows the pipes to be connected directly to the ECO radiator without an intermediate coupler. This reduces the risk of leakage and makes installation faster.
APART FROM THE UNIQUE FEATURES ALREADY MENTIONED, THE ECO RADIATOR ALSO OFFERS NUMEROUS OTHER ADVANTAGES FOR END USER INSTALLERS AS WELL AS WHOLESALERS .
THE HENRAD LOW-TEMPERATURE VALVE RADIATOR WITH SERIAL FLOW TECHNOLOGY, BOTH A CENTRE AND LATERAL BOTTOM CONNECTION AND A PRE-SET VALVE INSERT, WHICH CAN BE FITTED ON THE LEFT OR RIGHT SIDE OF THE RADIATOR.
TECHNICAL INFORMATIONHenrad Premium ECO
• Low-temperature panel radiator made from high-quality steel, with serial flow technology (water flows first through the front panel). This results in high energy efficiency, maximum radiation (even in low-temperature heating systems), faster heating rate and less waste of energy. Optimised in accordance with the requirements of EN442, EN12831 and DIN 4701-10.
• Quality assurance in accordance with ISO 9001. Heat output tested in accordance with EN442. Product quality certified by RAL.• Galvanised version available on demand.
FINISHING Upper grille and side panels
PRE-INSTALLED Pre-set Heimeier 4368 or 4369 valve insert, ECO air vent and blind plugs
VALVE INSERT The integrated adjustable valve insert (without thermostatic head) is factory-fit on the right side of the radiator, CEN certified, tested in accordance with EN215 and compatible with thermostatic heads M30 x 1.5 mm. For types 21 – 22 – 33 the valve insert can also be fitted on the left side of the radiator, a left version for a type 11 radiator is available on request.The thermostatic valve insert is factory-set in relation to the size of the radiator. This pre-setting ensures optimum throughput in the radiator. Factory setting for two-pipe systems, also suitable for one-pipe systems (as long as the valve insert is adjusted to position 8).
ALSO SUPPLIED VDI brackets (type Monclac), screws, plugs and installation instructions
CONNECTIONS 2 x ¾” male Eurocone centre connection and 2 x ½” female lateral bottom connection
LUGS 2 pairs of mounting lugs up to 1,600 mm and 3 pairs from 1,800 mm
PACKAGING Every radiator is sturdily packaged in high-quality cardboard and wrapped in plastic. The radiator’s characteristics are shown on the label: type – height – length
WARRANTY 10 years, as long as the installation instructions have been followed and Henrad’s warranty conditions have been met
PAINT PROCESS All radiators are degreased, phosphated, cataphoretically primed and powder-coated in Henrad white 9016 as standard
COLOUR Henrad white 9016 + 35 different Henrad colours and about 200 RAL-colours are possible
HEAT COST ALLOCATOR Suitable for heat cost allocators, both electronic and according to the evaporation principle (covered by the norm of EN834 & EN835).
MAX. OPERATING PRESSURE 10 bar (tested to 13 bar)
MAX. OPERATING TEMPERATURE 110°C
CONFORMITY In accordance with EN442
QUALITY ASSURANCE RAL and NF
DECLARATION OF EQUIVALENCE ISSO and Kiwa
TYPES 11 | 21 | 22 | 33
HEIGHTS 300 | 400 | 500 | 600 | 700 | 900 mm
LENGTHS 400 - 3,000 mm
DEPTHS 61 | 77 | 100 | 158 mm
21
TYPE 11 TYPE 21 TYPE 22 TYPE 33
CALCULATION FACTOR PER METRE OF RADIATOR LENGTH AT 75/65/20°C IN ACCORDANCE WITH EN442CHARACTERISTIC COMPARISON: Φ = KM × ΔTN.
Type overview *
W = output per metrekg = weight per metrel = water content per metrem² = surface area per metren = exponent
* The manufacturer retains the right to make changes to the products without prior notice.
HEIGHT (mm) TYPE 11 TYPE 21 TYPE 22 TYPE 33
300
W 509 744 933 1,347
kg 9.31 14.30 16.50 24.70
l 1.89 3.80 3.70 5.20
m² 2.09 2.44 3.51 5.26
n 1.32 1.28 1.31 1.33
400
W 676 927 1,173 1,686
kg 12.78 18.83 21.83 32.63
l 2.34 4.80 4.77 6.80
m² 2.95 3.37 4.92 7.38
n 1.31 1.29 1.30 1.33
500
W 833 1,107 1,401 2,007
kg 16.24 23.37 27.17 40.57
l 2.80 5.80 5.83 8.40
m² 3.80 4.31 6.33 9.49
n 1.30 1.30 1.30 1.33
600
W 980 1,287 1,617 2,313
kg 19.70 27.90 32.50 48.50
l 3.25 6.80 6.90 10.00
m² 4.66 5.24 7.74 11.61
n 1.29 1.30 1.30 1.33
700
W 1,117 1,467 1,824 2,607
kg 22.90 32.70 38.07 57.00
l 3.77 7.57 7.63 11.25
m² 5.51 6.18 9.15 13.72
n 1.29 1.31 1.30 1.33
900
W 1,360 1,836 2,220 3,180
kg 29.30 42.30 49.20 74.00
l 4.80 9.10 9.10 13.75
m² 7.22 8.05 11.97 17.96
n 1.29 1.32 1.30 1.33
76
77114
65
9761 100
137
87
195158
143
SUPPLIED ACCESSORIES: PRE-SET HEIMEIER VALVE INSERT, ECO AIR VENT, VDI BRACKETS, SCREWS, PLUGS AND INSTALLATION INSTRUCTIONS.
Output overview
Delivery times depend on the model: consult with your wholesaler.
HEIGHT 300 mm 400 mm 500 mm
TYPE 11 21 22 33 11 21 22 33 11 21 22 33
W/m EN442 55/45/20°C 259 W 387 W 479 W 684W 346 W 480 W 602 W 856 W 428 W 571 W 720 W 1,019 W
400 204152
298224
373279
539401
270201
371278
469351
674501
333249
443332
560419
803597
500 255189
372279
467348
674501
338252
464348
587438
843627
417311
554415
701523
1,004747
600 305227
446335
560418
808601
406303
556417
704526
1,012753
500374
664497
841629
1,204895
700 356265
521391
653488
943701
473353
649487
821614
1,180877
583436
775580
981733
1,4051,045
800 407303
595447
746557
1,078802
541404
742557
938701
1,3491,003
666498
886664
1,121838
1,6061,194
900 458341
670503
840628
1,212901
608454
834626
1,056789
1,5171,128
750561
996746
1,261943
1,8061,343
1,000 509379
744559
933697
1,3471,002
676504
927695
1,173877
1,6861,254
833623
1,107829
1,4011,047
2,0071,492
1,100 560417
818615
1,026767
1,4821,102
744555
1,020765
1,290964
1,8551,379
916685
1,218912
1,5411,152
2,2081,642
1,200 611455
893671
1,120837
1,6161,202
811605
1,112834
1,4081,052
2,0231,504
1,000748
1,328995
1,6811,257
2,4081,791
1,400 713531
1,042783
1,306976
1,8861,402
946706
1,298974
1,6421,227
2,3601,755
1,166872
1,5501,161
1,9611,466
2,8102,090
1,600 1,190894
1,4931,116
2,1551,602
1,082807
1,4831,112
1,8771,403
2,6982,006
1,333997
1,7711,326
2,2421,676
3,2112,388
1,800 1,3391,006
1,6791,255
2,4251,803
1,217908
1,6691,252
2,1111,578
3,0352,257
1,4991,121
1,9931,493
2,5221,885
3,6132,687
2,000 1,4881,118
1,8661,394
2,6942,003
1,3521,009
1,8541,391
2,3461,753
3,3722,507
1,6661,246
2,2141,658
2,8022,095
4,0142,985
2,200 1,6371,230
2,0531,534
2,9632,203
2,0391,529
2,5811,929
3,7092,758
1,8331,371
2,4351,824
3,0822,304
4,4153,283
2,400 1,7861,342
2,2391,673
3,2332,404
2,2251,669
2,8152,104
4,0463,009
1,9991,495
2,6571,990
3,3622,513
4,8173,582
2,600 2,4261,813
3,5022,604
3,0502,280
3,6432,723
2,800 2,6121,952
3,7722,805
3,2842,455
3,9232,933
3,000 2,7992,092
4,0413,005
3,5192,630
4,2033,142
23
HEIGHT 600 mm 700 mm 900 mm
TYPE 11 21 22 33 11 21 22 33 11 21 22 33
W/m EN442 55/45/20°C 507 W 662 W 831 W 1,174 W 577 W 751 W 938 W 1,323 W 703 W 933 W 1,142 W 1,615 W
400 392294
515385
647484
925688
447335
587438
730546
1,043776
544408
734546
888664
1,272946
500 490367
644482
809604
1,157860
559418
734548
912682
1,304970
680510
918683
1,110830
1,5901,183
600 588441
772577
970725
1,3881,032
670502
880657
1,094818
1,5641,163
816612
1,102820
1,332996
1,9081,419
700 686514
901674
1,132846
1,6191,204
782586
1,027767
1,277955
1,8251,357
952714
1,285956
1,5541,162
2,2261,656
800 784588
1,030770
1,294967
1,8501,376
894670
1,174876
1,4591,091
2,0861,551
1,088816
1,4691,093
1,7761,328
2,5441,892
900 882661
1,158866
1,4551,088
2,0821,548
1,005753
1,320985
1,6421,228
2,3461,745
1,224917
1,6521,229
1,9981,495
2,8622,129
1,000 980735
1,287962
1,6171,209
2,3131,720
1,117837
1,4671,095
1,8241,364
2,6071,939
1,3601,019
1,8361,366
2,2201,661
3,1802,365
1,100 1,078808
1,4161,059
1,7791,330
2,5441,892
1,229921
1,6141,205
2,0061,500
2,8682,133
1,4961,121
2,0201,503
2,4421,827
3,4982,602
1,200 1,176881
1,5441,155
1,9401,450
2,7762,064
1,3401,004
1,7601,314
2,1891,637
3,1282,326
1,6321,223
2,2031,639
2,6641,993
3,8162,838
1,400 1,3721,028
1,8021,347
2,2641,693
3,2382,408
1,5641,172
2,0541,533
2,5541,910
3,6502,714
1,9041,427
2,5701,913
3,1082,325
4,4523,311
1,600 1,5681,175
2,0591,540
2,5871,934
3,7012,752
1,7871,339
2,3471,752
2,9182,182
4,1713,102
2,1761,631
2,9382,186
3,5522,657
5,0883,784
1,800 1,7641,322
2,3171,733
2,9112,176
4,1633,096
2,0111,507
2,6411,972
3,2832,455
4,6933,490
2,4481,835
3,3052,459
3,9962,989
5,7244,257
2,000 1,9601,469
2,5741,925
3,2342,418
4,6263,440
2,2341,674
2,9342,190
3,6482,728
5,2143,878
2,7202,039
3,6722,733
4,4403,321
6,3604,730
2,200 2,1561,616
2,8312,117
3,5572,659
5,0893,784
2,400 2,3521,763
3,0892,310
3,8812,902
5,5514,128
2,600 4,2043,143
2,800 4,5283,385
3,000 4,8513,627
EN442 (W) 70/50/20°C
EN442 (W) 75/65/20°C
THE LOW-TEMPERATURE VALVE RADIATOR SPECIFICALLY DEVELOPED FOR ENVIRONMENTS WHERE HYGIENE AND SAFETY ARE ALL-IMPORTANT, WITH SERIAL FLOW TECHNOLOGY, BOTH A CENTRE AND LATERAL BOTTOM CONNECTION AND A PRE-SET VALVE INSERT, WHICH CAN BE FITTED AND THE LEFT OR RIGHT SIDE OF THE RADIATOR.
TECHNICAL INFORMATIONHenrad Hygiene ECO
• Low-temperature panel radiator made from high-quality steel, with serial flow technology (water flows first through the front panel). This results in high energy efficiency, maximum radiation (even in low-temperature heating systems), faster heating rate and less waste of energy.Optimised in accordance with the requirements of EN442, EN12831 and DIN 4701-10.
• Quality assurance in accordance with ISO 9001. Heat output tested in accordance with EN442. Product quality certified by RAL.• Galvanised version available on demand.
FINISHING Without upper grille or side panels
PRE-INSTALLED Pre-set Heimeier 4368 or 4369 valve insert, ECO air vent and blind plugs
VALVE INSERT The integrated adjustable valve insert (without thermostatic head) is factory-fit on the right side of the radiator, CEN certified, tested in accordance with EN215 and compatible with thermostatic heads M30 x 1.5 mm. For types 20 and 30 the valve insert can also be fitted on the left side of the radiator, a left version for a type 10 radiator is available on request.The thermostatic valve insert is factory-set in relation to the size of the radiator. This pre-setting ensures optimum throughput in the radiator. Factory setting for two-pipe systems, also suitable for one-pipe systems (as long as the valve insert is adjusted to position 8).
ALSO SUPPLIED Installation instructions
CONNECTIONS 2 x ¾” male Eurocone centre connection and 2 x ½” female lateral bottom connection
LUGS 2 pairs of mounting lugs up to 1,600 mm and 3 pairs from 1,800 mm
PACKAGING Every radiator is sturdily packaged in high-quality cardboard and wrapped in plastic. The radiator’s characteristics are shown on the label: type – height – length
WARRANTY 10 years, as long as the installation instructions have been followed and Henrad’s warranty conditions have been met
PAINT PROCESS All radiators are degreased, phosphated, cataphoretically primed and powder-coated in Henrad white 9016 as standard
COLOUR Henrad white 9016 + 35 different Henrad colours and about 200 RAL-colours are possible
HEAT COST ALLOCATOR Suitable for heat cost allocators, both electronic and according to the evaporation principle (covered by the norm of EN834 & EN835)
MAX. OPERATING PRESSURE 10 bar (tested to 13 bar)
MAX. OPERATING TEMPERATURE 110°C
CONFORMITY In accordance with EN442
QUALITY ASSURANCE RAL and Hygiene
TYPES 10 | 20 | 30
HEIGHTS 300 | 400 | 500 | 600 | 700 | 900 mm
LENGTHS 400 - 3,000 mm
DEPTHS 47 | 77 | 158 mm
25
TYPE 10 TYPE 20 TYPE 30
7
472525
49
7788 169
158
119
CALCULATION FACTOR PER METRE OF RADIATOR LENGTH AT 75/65/20°C IN ACCORDANCE WITH EN442CHARACTERISTIC COMPARISON: Φ = KM × ΔTN.
Type overview *
W = output per metrekg = weight per metrel = water content per metrem² = surface area per metren = exponent
* The manufacturer retains the right to make changes to the products without prior notice.
HEIGHT (mm) TYPE 10 TYPE 20 TYPE 30
300
W 338 585 867
kg 6.17 11.57 17.80
l 1.89 3.71 5.50
m² 0.68 1.37 2.04
n 1.28 1.27 1.30
400
W 430 732 1,074
kg 8.22 15.35 23.27
l 2.34 4.71 7.07
m² 0.91 1.83 2.73
n 1.29 1.28 1.30
500
W 521 879 1,275
kg 10.28 19.12 28.73
l 2.80 5.70 6.83
m² 1.14 2.28 3.42
n 1.30 1.28 1.30
600
W 610 1,023 1,470
kg 12.33 22.90 34.20
l 3.25 6.70 10.20
m² 1.37 2.74 4.11
n 1.31 1.29 1.31
700
W 699 1,167 1,659
kg 14.19 26.83 40.10
l 3.77 7.57 11.33
m² 1.60 3.20 4.79
n 1.32 1.29 1.31
900
W 877 1,458 2,034
kg 17.90 34.70 51.90
l 4.80 9.30 13.60
m² 2.06 4.12 6.17
n 1.33 1.30 1.32
SUPPLIED ACCESSORIES: PRE-SET HEIMEIER VALVE INSERT, ECO AIR VENT AND INSTALLATION INSTRUCTIONS.
Output overview
HEIGHT 300 mm 400 mm 500 mm
TYPE 10 20 30 10 20 30 10 20 30
W/m EN442 55/45/20°C 176 W 306 W 447 W 222 W 381 W 553 W 268 W 457 W 655 W
400 135 234 347 172 293 430 208 352 510102 176 260 129 220 321 156 264 381
500 169 293 434 215 366 537 261 440 638127 220 325 161 275 402 195 330 477
600 203 351 520 258 439 644 313 527 765152 264 389 193 330 482 234 396 572
700 237 410 607 301 512 752 365 615 893178 308 454 226 385 562 273 462 667
800 270 468 694 344 586 859 417 703 1,020203 352 519 258 440 643 312 528 763
900 304 527 780 387 659 967 469 791 1,148228 396 584 290 496 723 351 594 858
1,000 338 585 867 430 732 1,074 521 879 1,275254 441 649 322 551 804 389 660 953
1,100 372 644 954 473 805 1,181 573 967 1,403279 485 714 354 606 884 428 726 1,049
1,200 406 702 1,040 516 878 1,289 625 1,055 1,530305 529 779 387 661 964 467 792 1,144
1,400 473 819 1,214 602 1,025 1,504 729 1,231 1,785355 617 909 451 771 1,125 545 924 1,334
1,600 936 1,387 688 1,171 1,718 834 1,406 2,040705 1,039 516 881 1,286 623 1,056 1,525
1,800 1,053 1,561 774 1,318 1,933 938 1,582 2,295793 1,168 580 991 1,446 701 1,189 1,716
2,000 1,170 1,734 860 1,464 2,148 1,042 1,758 2,550881 1,298 644 1,101 1,607 779 1,321 1,906
2,200 1,287 1,907 1,610 2,363 1,146 1,934 2,805969 1,428 1,211 1,768 857 1,453 2,097
2,400 1,404 2,081 1,757 2,578 1,250 2,110 3,0601,057 1,558 1,321 1,928 935 1,585 2,288
2,600 1,521 2,254 1,903 2,2851,145 1,688 1,431 1,717
2,800 1,638 2,428 2,050 2,4611,234 1,818 1,542 1,849
3,000 1,755 2,601 2,196 2,6371,322 1,947 1,652 1,981
Delivery times depend on the model: consult with your wholesaler.
27
EN442 (W) 70/50/20°C
EN442 (W) 75/65/20°C
HEIGHT 600 mm 700 mm 900 mm
TYPE 10 20 30 10 20 30 10 20 30
W/m EN442 55/45/20°C 312 W 530 W 754 W 356 W 603 W 850 W 444 W 749 W 1,038 W
400 244 409 588 280 467 664 351 583 814182 307 439 208 350 495 261 436 606
500 305 512 735 350 584 830 439 729 1,017227 384 549 260 437 619 326 545 758
600 366 614 882 419 700 995 526 875 1,220273 461 659 312 525 743 391 654 910
700 427 716 1,029 489 817 1,161 614 1,021 1,424318 537 769 364 612 867 456 763 1,061
800 488 818 1,176 559 934 1,327 702 1,166 1,627364 614 879 417 700 991 521 872 1,213
900 549 921 1,323 629 1,050 1,493 789 1,312 1,831409 691 988 469 787 1,115 587 981 1,365
1,000 610 1,023 1,470 699 1,167 1,659 877 1,458 2,034455 768 1,098 521 874 1,238 652 1,090 1,516
1,100 671 1,125 1,617 769 1,284 1,825 965 1,604 2,237500 844 1,208 573 962 1,362 717 1,199 1,668
1,200 732 1,228 1,764 839 1,400 1,991 1,052 1,750 2,441546 921 1,318 625 1,049 1,486 782 1,308 1,819
1,400 854 1,432 2,058 979 1,634 2,323 1,228 2,041 2,848637 1,075 1,537 729 1,224 1,734 912 1,526 2,123
1,600 976 1,637 2,352 1,118 1,867 2,654 1,403 2,333 3,254728 1,228 1,757 833 1,399 1,982 1,043 1,744 2,426
1,800 1,098 1,841 2,646 1,258 2,101 2,986 1,579 2,624 3,661819 1,382 1,977 937 1,574 2,229 1,173 1,962 2,729
2,000 1,220 2,046 2,940 1,398 2,334 3,318 1,754 2,916 4,068910 1,535 2,196 1,041 1,749 2,477 1,303 2,180 3,032
2,200 1,342 2,251 3,2341,001 1,689 2,416
2,400 1,464 2,455 3,5281,092 1,842 2,636
2,600 2,6601,996
2,800 2,8642,149
3,000 3,0692,303
TYPE 10 - 11 TYPE 20 - 33
TYPE 10 - 11
TYPE 20 - 33
25
L
L/2L/2
½“
¾”EUROKONUS ¾”
EUROKONUS 50
122x "
50
25
12"
122x2x EUROKONUS "
25
12"
505050
Cross section
Cross section Cross section
Front
Front
35-1
15m
m
115-
155m
m
TYPE 10 - 22 TYPE 30 - 33
35-1
15m
m
115-
155m
m
35-1
15m
m
115-
155m
m
VIEW: Front radiator.
Bottom side radiator
Bottom side radiator
T1642 (Including spacer)
Valve leftValve left* Valve rightValve right
* On demand.
VALVE CAN BE FITTED ON THE LEFT OR THE RIGHT.
CONNECTION SIZES
Connection options
Installation template
L: Length (from 400 to 3,000 mm)Minimum distance to bottom of radiator: 120 mm.
CORNER BRACKET
TYPE 10
J-BRACKET (FOR VDI 6036)
TYPE 11 - 33
TYPE 11 TYPE 20 - 21 TYPE 22 TYPE 30 - 33
77114
76
9761
65
100137
87
158195
143
48
Y
X
Art. No. T1507
2x
2x
2x2x
2x
Bottom side radiator
HEIGHT(mm) X Y Art. No.
(2 pcs.)Art. No.(3 pcs.)
300 - 151 R509203 R509303
400 49 251 R509204 R509304
500 49 351 R509205 R509305
600 49 451 R509206 R509306
700 49 551 R509207 R509307
900 49 751 R509209 R509309
TYPE 10
407
4773
29
Wall brackets
TYPE 11
TYPE 10, TYPE 20 - 33
L: 400-1,600
60
A
8585
A
A
L: 400-1.600
60 85
A
85
8585
A
L: 1,800-3,000
L/2 + 17mm
60
A
A
L: 1.800-3.000
L/2
60 85
A
85
L A
400 117
500-3,000 150
L A (TYPE 10) A (TYPE 20-33)
400 100 133
500-1,100 167 133
1,200-3,000 267 133
Mounting lug positions
ML110 ML120 ML130 ML140 ML150 ML160 ML170
NT110
SN110
Papyrus white
Cream white
NT120
SN120
Pearl white
Cream
NT130
SN130
Champagne
Mocca
NT140
SN140
Beige
Bordeaux
NT150
SN150
Beige grey
Sepia
NT160
SN160
Pebble grey
Pale blue
NT170
SN170
Quartzgrey
Black
NATURAL COLOURS
METALLIC COLOURS
SANITARY COLOURS
Dove grey Titanium grey
Blue grey Granite Cappuccino Terra brown
Graphite black
Warmth is indispensable for a snug home. Just like an interior in which you feel good. A place to come home to. When choosing Henrad you are also choosing colourful warmth.
How to order a coloured
radiator Select the radiator’s item number then the colour code and colour description, e.g. 0274202206 SN170 Black
COLOUR YOUR WARMTH
RAL COLOURS
The colours are illustrative only.
A1004Golden yellow
Anthracite grey
A7016
A2003Pastel
orange
Stone greyA7030
A3002Carmine
red
Light greyA7035
A5002Ultramarine
blue
Chocolate brown
A8017
A6018Yellow green
Signal whiteA9003
A7001Silver grey
Jet blackA9005
A7011Iron grey
Pure whiteA9010
HENRADHenrad N.V.Welvaartstraat 14 bus 6 | 2200 Herentals | BelgiumT. +32 14 212 075 | F. +32 14 211 719
WWW.HENRAD.EU
FOR MORE INFORMATION, CONTACTE-mail: [email protected]
HENRAD
Algeria Australia Belgium Cyprus Czech Republic France
Germany Greece Iceland Lithuania Luxembourg The Netherlands
Poland Russia Slovenia Sweden Tunisia Ukraine
HR
ECO
TD
EN
- 2
017/
11
