Technical of Our Diamond Tools

8/14/2019 Technical of Our Diamond Tools

1/41

Technical of our diamond tools

1. Polishing Pad

Flexible Wet Polishing Pads

The faces of polishing pads are designed with straight or curved slots, so they could be bent

or distorted freely. They are backed with loop Velcro so they could be attached to any of

backer pads very easy. They are used for fabrication of marble, granite, ceramic, and other

hard and fragile material, as well as non-iron metal. They are widely used to polish stone,

porcelain profiles, tile floors, all kinds of table-boards and stone sculptures.

Their working layer thickness is 2.2mm, 3mm or 4mm

They are suitable for hand power machines with the power is 750W to 1500W that run up to a speed of 2000-10000

rpm.

Flexible Polishing Pads attach to the Flexible Backer pads are used for grinding profiles or concave or convex surface

as well as flat surface of stone, while attach to the rigid backer pads are perfect for grinding a flat or level surface like

floor.

The process procedure: the operator sticks the flex pad on a backer pads and screw into Arbor of a grinding machine,

and then brings to bear some pressure to the machine to grind stone surface for five times come-and-go, at the same

time, the operator must infuses water into the backer pad continuously during the operation.

Then, the operator should change a finer pad. The grits of pads are from #50, #100, #200,#400, #800, #1500, #3000, and #5000 to white/black buff in turn.According to the stone's

quality and operator's experience, it could be cut down or save some positions of pads.

White buff is used for light color stones and black buff for dark color stones. Each of grit is

easily distinguished by different color of Velcro and the grit mark on the pad.

They are worked by water fed during the operation, so they are also called wet pads.

GRIT #50 #100 #200 #400 #800 #1500 #3000 #5000 BUFF

COLOR BLUE YELLOW ORANGE RED DARK GREEN LIGHT GREEN COFFEE WHITE WHITE

GLOSSY 1 2 5 10 20 35 65 85 90

WATER QUANTUM MUCH MUCH MUCH MIDDLE FEW FEW FEW FEW FEW

Measly water is needed from #1500, to #3000. For the buff, only less water is needed to wet the stone surface. This

would make more friction resistance, and enough temperature on the surface of stone. Then stone surface is easily to

be wiped off because of intenerate caused by momentary high temperature. But the stone couldn't be grinded by dry

with too long time or it will result in burning or pigmentation. If burning appears, the worker must do work over again

from #200 at least, and if the pigmentation appears, it must be from #400.

PDF "pdfFactory Pro" www.fineprint.cn
http://www.fineprint.cn/http://www.fineprint.cn/http://www.fineprint.cn/


2/41

Flexible Dry Polishing Pads

Some special floors (e.g. hotel's stone floorboard) are not allowed to work by wet, so the dry pads are used. Ordinarily,

the dry pads will not cause burning and pigmentation because of using the special resin to make the surface of pads

intenerated and pealed off as well as to avoid too hot on the surface of stone.

They are excellent for marble polishing. They can be used by wet as well.

Flexible Buff Pads

As the last position of pads or as the last stage of the fabrication, these pads are designed to create a deep glossy

reflection mirror like on marble, terrazzo and granite. Only a little water is necessary so the pads can work with heat

and water and a smooth finish surface would be done quickly.

The pads are made from tin oxide and natural fibers and special bond that are heat compressed into a mould. As there

are no dangerous chemicals involved, the Buff Pads are environmental safe and easy to use.

Flexible Resin-Pregnant Diamond Metal Chips Polishing Pads

For improving the efficiency to quickly remove stock and for increasing the Durable life of

pad set significantly, we creates resin-metal-bond polishing pads, available from #30, #50,

#100,#200 to #400, available both by wet and by dry.

They are made with pregnant diamond metal chips with unique resin bond. They are heat

compressed into a mould.

This is a new kind of high capability pads. They can be applied to excellent fabrication of

marble, concrete and granite . They are welcomed by our consumers with very much

interest.

Customer Logo printed is available on request for volume order.

Flexible Metal bond Polishing Pad

Sintered metal bonded with Rubber backer pad backed applied to quickly remove stock.

They are available from #30, #50, #100,#200 to #400 .



3/41

Flexible Electroplated of Diamond Polishing Pads

Electroplated of diamond crystals on a flexible cloth with dot matrix or a special pattern,

they are mainly used for dry polishing. They are available from grit #60, #120, #200 to

#400 .

Convex Polishing Pads

They are designed for polishing curved or inner concave parts of countertops, furniture,

sinks, and cast stone. Available in 3".


POLISHING PAD-SKETCH MAP



4/41

2. Brazed Polishing Pads

Brazed Polishing Pads Velcro or Rubber Backer Backed

Brazed diamond on a thin round steel sheet with Velcro or Backer pad

backed. You can easy mount on any machine. Since it is a brazed

diamond tool with 50-80% diamond exposure it can be applied to

excellen heavy removal for marble, concrete and granite wthout shaking

even run by dry.

it is available in both 4" ,4-1/2"and 5" diameter and available on request

upon a specific drawing of customer in any diameter for a volume order.




5/41

3. Floor Polishing Pads

Floor Polishing Pads

They are designed for floor polishing machines to polish or restore or

maintain for the floor of marble, concrete, terrazzo, granite. They are

backed with Velcro, can be mounted on a rigid backer pad to fit on any

floor machine. The high thickness provides extended life.

Our resin-pregnant diamond Metal chips floor polishing pads,

available from #30, #50, #100, to #200, are for quickly remove stock

with durable life. This is a vitally important innovation in diamond tools

industry.

Our high concentration of diamond resin floor polishing pads from

#400, #800, #1500 to #3000 are made from heavy-duty resin with

high quality diamond powder.

Using our set of floor polishing pads you can make the floor glossy

finish perfectly.

They are available in wet and dry on request.

We have many kinds of rigid backer pads; they are bakelite baker

pad, aluminum backer pad, aluminum and rubber composite backer

pad with female threaded 5/8-11" or M14 and availble with other

threads on request.

Available in 3" and 4" diameter, thickness from 8mm to 12mm on

customer request.

We have sintered cup wheels; they are designed to initially shape the floor of concrete,

terrazzo and granite.




6/41

4. Sintered Router Bits

Sintered Router Bits for Portable profile machines

These Sintered Router Bits have a M8 threaded bolt attached

and a M10 threaded bolt backed up to fit on any Portable

Profile Machine. They may be run by wet with the water rushed

from a attachment of the machine.

Choose from segmented for aggressive stock removal or continuous rim for a smoother finish.

Customer Logo printed is available on request for volume order

SKETCH MAP

Sintered Router Bit for Angle Grinders

These Sintered Router Bits for Angle Grinder have a 5/8"-11 or M14 female threaded on customer

request to fit on any Anger Grinder. They may be run by wet with the water out from the center hole

and vents inside the arbor.

Choose from segmented tools for aggressive stock removal or continuous rim for a smoother

finish.

Attached with a composite elasticity gasket for vibration-proof is available.



7/41



8/41

5. Brazed Router Bits

Brazed Router Bit for Angle Grinders

These Vacuum Brazed Router Bits for Angle Grinder have a 5/8"-11 or M14 female

threaded on customer request to fit on any Anger Grinder. They may be run by wet

with the water out from the center hole and vents inside the arbor.They can be run

by dry also.

Vacuum Brazed Router Bits are great for grinding shapes without bouncing or

loosing their shape. They feature 50% up to 80% diamond exposure to ensure you

that get the fastest removal rate. We strongly suggest our customer to choose

Sintered as POS1, Vacuum Brazed as POS2 and POS3, and then resin polishing

wheels as POS4, POS5 and POS6.

They are excellent for fabrication of marble, granite, reinforced fiber composites,

hard rubber, hard plastic, carbon fiber composites, glass

Attached with a composite elasticity gasket for vibration-proof is available.

They are the best tools to replace electroplated Router Bits. The life of brazed bit is

5 times than electroplated.


Brazed Router Bits for Portable profile machines

These Vacuum Brazed Router Bits have a M8 threaded bolt attached and a M10

threaded bolt backed up to fit on any Portable Profile Machine. They may be run by

wet with the water rushed from an attachment of the machine. They can be run by

dry also.

They are great for grinding shapes without bouncing or loosing their shape. They

feature 50% up to 80% diamond exposure to ensure you that get the fastest

removal rate. We strongly suggest our customer to choose Sintered as POS1,

Vacuum Brazed as POS2 and POS3, and then resin polishing wheels as POS4,POS5 and POS6.

They are excellent for fabrication of marble, granite, reinforced fiber composites,

hard rubber, hard plastic, carbon fiber composites, glass

They are the best tools to replace electroplated Router Bits. The life of brazed bit is

5 times than electroplated.




9/41

6. CNC Profile Wheels

We offer the high quality and reliability of CNC profiling wheels

for the profiling of granite, marble and synthetic stone.

They are sintered and welded in a mould at same time under

strict guidelines with the best diamond available.

Segmented tools are for aggressive stock removal and

continuous rim for a smoother finish.

Available upon a specific drawing of customer, we can make any

wheel in any diameter requested and with a combination of many

different shapes.

Vacuum Brazed CNC Profile Wheels

They are great for grinding without bouncing or loosing their

shape. They are perfect to be position 2 and 3 in the set of tools.

The set of tools consists of 3 metal bonded diamond wheels

perfectly matched to 3 resin diamond polishing positions. This

makes it possible to obtain the maximum degree of finishing without the need for manual

working.

We strongly incline the set of tools consists of 1 sintered metal bonded profile wheel as

position 1, 2 Vacuum brazed wheels as position 2 and 3, and then matching to 3 resined

polishing wheels as position 4, position 5 and position 6.

Standard bore is 35mm, available in other bores. Our wide ranges of profile wheels are

suitable for use on all major CNC machines

Available on request for Marble and Granite, upon a specific drawing of customer, these

wheels can be made in any diameter requested and with a combination of many different

shapes.

Delivery time is less than 4 weeks.




10/41

7. Finger Bits

They are designed with G1/2" male thread, mounted on a CNC machine,working as

milling cutter for cutting any arc of granite or marble or other stones under the

control of CNC machine, continuous rim with arc slots and water vents throughout of

body. Other styles are available according to the drawings of customer.

Available in both sintered and vacuum brazed. Sintered is more economical and

vacuum Brazed is great with high efficiency without bouncing or loosing their shape.

Designed with edge 3/16" Radius or other shape edge make a finger bit becoming a Pofile Finger Bit, or 2 in 1.

We offer many adapters. Adapter unit screws into a Finger Bit to affect operative compatibility between different

machines.

It is available on request upon a specific drawing of customer in any diameter and length.


FINGER BIT-SKETCH MAP



11/41

SPECIFICATION:



12/41

8. Sintered Drill Bits

Sintered Crown Core Bits

Our Core Bits are thin wall drilling tool with a hole through the

center that let water feeds into and removes sediment stone

chips and allows the Core pedestal to pass through the Bit and

into the Core barrel.

Our Drill Bits, used with high quality diamond and strong bond,

sintered into a mould, are Laser welded. They are high diamond

concentration provide aggressive cutting action, excellent for

drilling marble and granite with high performance and durable

life. They are designed with 5/8"-11 or M14 or M10 female

thread and attached with a composite elasticity gasket so they

can be mounted to any angle grinder and work on stone with

vibration-proof.

We offer many adapters. Adapter unit screws into a Drill Bit to

affect operative compatibility between different machines.

Sintered Non Core Bits

A non Core Bit is a drilling tool with a hole

through the center that let water flows and

removes sediment stone chips. It drill the stone

complete section with no core.

They are designed with composite threaded both with G1/2"

male threaded and 5/8-11 or M14 female threaded, so that they

can not only be mounted to any angle grinder but also can be

used on CNC machine.

Attached with a composite elasticity gasket with vibration-proof

is available for all drill bits.

Available in G1/2", 5/8-11, M14, M10, 3/8 Shank, 1/2 Shankon customer's order.

We offer many adapters. Adapter unit screws into a Drill Bit to affect operative compatibility between

different machines.

It is available on request upon a specific drawing of customer in any diameter and length requested.




13/41

9. Brazed Drill Bits

Crown Core Bits with brazed of Diamond wall

Called Sintered Crown Core Bit with Vacuum

Brazed Drum

Beside the sintered tips, they are brazed of diamond on

the wall of the crown Core Bits, so a normal Core Bit

become a drum grinder, it is extended a amusing

application for a Core Bit.

Vacuum Brazed Core Bits & Drum Grinder

They are thin wall Core Bits and Drum Grinders. They are

used when it is not allowed to drill hole or extend hole by

wet on granite, marble, porcelain, ceramic tile.

Vacuum Brazed Drill Bits

They are thin wall designed. They are used when it is not

allowed to drill hole by wet on granite, marble, porcelain,

ceramic tile.

Attached with a composite elasticity gasket for

vibration-proof is available for all drill bits.

Available in G1/2", 5/8-11, M14, M10, 3/8 Shank, 1/2

Shank for all drill bits on customer's order.

It is available on request upon a specific drawing of customer in any diameter and length

requested.

Customer Logo printed is available on request for volume order



14/41


15/41

TYPE

NO DIAMETER(D2) Thread Size (D1) GRIT

1 4"

2 5"

3 6"

4 7"

20M14M165/8"-11Snail Lock #35/40#70/80#140/200

SPECIFICATION-DOUBLE ROW

DIAMENSION

D2 R1 R2 r1 r2 W1 W2 LENGTHWIDTHDEPTH

100 50 43 37 31 30 20 3075 ,2065

125 62.5 54.5 47 40 38 25 3885 ,2575

150 75 67 56 49 45 30 4585 ,3075

175 87.5 79.5 65 58 52 35 5285 ,3575

SPECIFICATION-RADIATE



16/41

DIAMENSION

D2 D1 R1 R2 W LENGTHWIDTHDEPTH

100 50 43 30 3075

125 62.5 54.5 38 3885

150 75 67 45 4585

175

20M14M165/8"-11Snail

Lock

87.5 79.5 52 5285

SPECIFICATION

NO DIAD2) THREAD SIZE (D1) GRIT

1 4"

2 5"

3 6"

4 7"

20M14M165/8"-11Snail

Lock#35/40#70/80#140/200

SPECIFICATION-TURBO



17/41

DIAMENSION

D2(mm) D1 d2(mm) d1(mm)

100 60 30

125 75 30

150 90 30

175

20M14M165/8"-11Snail Lock

105 30

SPECIFICATION

NO DIA(D2) THREAD SIZE (D1) GRIT

1 4"

2 5"

3 6"

4 7"

20M14M165/8"-11Snail Lock #35/40#70/80#140/200



18/41

11. Brazed cup wheels

Vacuum Brazed cup wheels are great for grinding bevels or shapes without bouncing or loosing their shape. Available

in both 4" and 5" diameter. Other styles are available according to the drawings of customer

Available in Bore16mm, 7/8", female 5/8"-11 and M14 or on customer's order.

It is available on request upon a specific drawing of customer in any diameter and height requested.




19/41

12. Diamond Polishing Bricks

They are used to replace Silicon Carbide Bricks.

Our Sintered Diamond Bricks, grits from #30/40, #40/50,

#50/60, #70/80, #80/100, #100/120 to #140/200, are

designed to initially shape with high stock removal rate

for the slab fabrication of granite or marble. The rubber

iterlayer make for vibration-proof.

Our high concentration of diamond Resin Bricks from

#300, #400,# 500, #800, #1500 to# 3000 made from

heavy-duty resin with high quality diamond powder are perfect for polishing granite or marble.

Our BUFF Bricks made of special rubber bond and tin dioxide and other materials make high

glossy finish on the slab of granite perfectly. White BUFF is for light color granite and black

BUFF for deep color granite.

It is available on request upon a specific drawing of customer in any size.


SPECIFICATION



20/41

NO DIA BOND TYPE GRIT

1 #35/40

2 #40/50

3 #50/60

4 #70/80

5 #80/100

6 #100/140

7

METAL

#140/200

8 #200

9 #300

10 #400

11 #500

12 #1000

13 #2000

14 #3000

15 #5000

16

135mm,140mm,

RESIN

BUFF



21/41

13. Vacuum Brazed Dishs

Vacuum Brazed Dishes are great for grinding bevels or shapes without bouncing or loosing their shape. Available in

both 4" ,4-1/2"and 5" diameter. Other styles are available according to the drawings of customer.

Available in Bore16mm or 7/8", or laser welded 5/8"-11 threaded Nut or M14 theaded or M10 threaded Nut, on

customer's order.

It is available on request upon a specific drawing of customer in any diameter and height requested.




22/41

14. Drum Grinders

They are used with an up and down motion, excellent for grinding an inside circle,

oval, or arc of granite or marble or other stones. The sintered drums are economic

for longer life. The brazed drums are for fast cutting and could be used by dry. The

resin drums are for polishing, with rubber interlayer they can work at high speed

smoothly.

Available in G1/2", 5/8-11 female threaded, M14 female threaded, M10 female

threaded, 3/8 Shank, 1/2 Shank on customer's order.

We offer many adapters. Adapter unit screws into a Drum Grinder to affect

operative compatibility between different machines.

It is available on request upon a specific drawing of customer in any diameter and

length requested.




23/41

15. Backer Pads

The backer pads are hook Velcro backed, they accept polishing pads with Velcro

loop backed. We have rigid backer pads made from Bakelite, Flexible backer pads

made from rubber, extremely flexible backer pads made from supper quality rubber .

Our extremely flexible backers are great for ogees.

Flexible backer pads are used for grinding profiles or curves surface of stone while

the rigid backer pads are for grinding plane or floor.

All the backer pads are ideally suited for all kinds of machines with Arbor 5/8-11

threaded or M14 threaded. It is available on request upon a specific drawing of

customer in any diameter and height requested.

Available in 3",4", 5",6",7" diameter.

Snail Lock Adapter

They are made from Bakelite or Rubber with hook Velcro backed, they accept polishing pads with Velcro loop backed.

Available in 4", 5", 6" and 7" diameter.

We also produce polishing pads with a snail lock adapter .


Adapters

They are made from stainless steel.

Adapter unit screws into a core bit or a drum to affect operative compatibility between different machines.

It is available on request upon a specific drawing of customer in any diameter or thread and length.




24/41

SPECIFICATION:

DIAMENSION

D 60, 80, 100, 125, 150

d M14, M16, 5/8"-11, snail lock



25/41

16. Diamond Hand Pad

Hand-Hold Flat and Profile Polishing Pads

They are foam backed for polishing on the surface of marble,

granite, ceramics, glass and hard composites. Flat pads are for for

polishing plane and the Profile Pads are allowed for easy polishing

the profile shapes or the areas that are hard to polishing by

machines. They are good at edging or seaming polishing.

For the coarser grit pads are electroplated diamond on flexible

cloth and foam-backed, available in the grits# 60, #120, #200 and

#400.

For the finer grits, they are resined diamond on flexible cloth and

foam-backed available in the grit #600, #1800 and #3500.




26/41

17. Other Product

Vacuum Brazed Anchor Bits

We offer many kinds of Vacuum Brazed like 3/8", 1/4" or 3/16"

of diamond Anchor Bits. Standard Shank is 3/8". Other shanks

like 1/4" or non Standard Anchor Bits are available on the

request of customer.

Customer Logo printed is available on request for volume

order.

Here is the diagram for the application of an Anchor bits. After

milling the hole, the slab of stone is mounted by an anchor bolt

to the base.

JIGSAWS

straight narrow vertical blade, used to cut sharp corners or

joints of slabs, where could not be cut by a circular saw blade,

by up-down motion, it is also for cutting curves in granite,

marble, ceramic tiles and many other natural or artificial

stones.

We have sintered and Vacuum Brazed diamond Jigsaw both

welded by laser.

Customer Logo printed is available on request for volume

order.

Sintered Router Tip

Other threads are available on customer's order.

It is available on request upon a specific drawing of customerin any diameter and length requested.

Brazed tips of diamond wire saw

We offer many sizes of brazed tips of diamond for manufacture of diamond wire saw.



27/41

18. Cutting Tools

Gang saw segment

Brief introduction: For cutting marble, limestone and other soft stone.

Regular sizes are as following, other specifications and sizes are available upon request.

Thickness of the

blade(mm)

Height of the

blade(mm)

Legth of the

blade(mm)

Width of the

segment(mm)

Height of the

blade(mm)

Length of the

blade(mm)

3 180 3.0-4.0 4.5 7 20

3.5 180 3.0-4.0 5 7 20

Please forward us the following technical data when ordering the above products.

Diameter: Specification of Segment Order Amount

Diameter of Inner hole Number of Segments in Each Blade Delivery Date:

Cutting Material

Please forward us the following technical data if it is available for you!

Turning Speed of Blade(rpm/min) Linear Speed(m/min) Motor Power(KW)

Cutting Depth(m/min) Cutting Depth(mm)Cooling Water

Comsuption(L/min)

Main Characteristic of Cutting Material



28/41

Horizontal cutting blade

Brief introduction: High frequency welded, for horizontal cutting marble ,granite, basalt and so on

Characteristics of products: Good sharpness, stable cutting, flat cutting gap

Diameter (mm ) Universal disk thickness(mm) W1( mm) H(mm) L(mm) Number

300 2.8/7 4.5 10 40 21

350 2.8/7 4.5 10 40 24

400 2.8/7 4.5 10 40 28

450 2.8/7 4.5 10 40 32




Cutting Material




Comsuption(L/min)




29/41

multi-saw blade and segment

Brief Introduction: High Frequency welded or brazing welded,numerously used for cutting granite

Characteristics of products:Sandwich structure, fast, straight and stable cutting with flat slab,good life span.

Regular sizes are as following, other specifications and sizes are available upon request.

Diameter (mm ) W1 W2 H L Number

1000 6.9 6.1 13 24 70

1200 7.4 6.6 13 24 80

1300 8.4 7.6 13 24 88

1400 8.4 7.6 13 24 92

1600 9.2 8.4 13 24 108




Cutting Material




Comsuption(L/min)




30/41

Blade and segment for cutting large size block

Diameter (mm ) W1 W2 H L Number

900 6.9 6.1 13 24 64

1000 6.9 6.1 13 24 70

1100 7.4 6.6 13 24 74

1200 7.4 6.6 13 24 80

1300 8.4 7.6 13 24 88

1400 8.4 7.6 13 24 92

1500 9.2 8.4 13 24 100

1600 9.2 8.4 13 24 108

1700 9.2 8.4 13 24 112

1800 9.9 9.1 13 24 120

2000 11.0 10.0 15 24 128

2200 11.0 10.0 15 24 132

2500 12.5 11.5 20 24 140

2700 12.5 11.5 20 24 140

3000 12.5 11.5 20 24 160

3500 13.0 12.0 20 24 180



31/41

Wire saw

Brief introduction: For quanrrying,profiling and block finishing of granite,marble,limestone and other stone, and also cutting concrete.

Characteristics of products: Good sharpness, moderate life span, stable performance.

Specifications,technics and sizes are available upon requests.

Specifications

mm

Diameter

mm

Height of

working

layer

mm

mm

Length

Material

to cutUsage Techniques

11 11 6 9.5 Marble Quarrying Sintered

10.5 10.5 6.4 10 Marble

Block

squaring Sintered

8.5 8.5 6 9.5 Marble Profiling Sintered

8.8 8.8 6 9.5 Marble Profiling Sintered

11 11 6.4 10 Marble Quarrying Sintered

11.5 11.5 6.4 10 Marble Quarrying Sintered

10.5 10.5 6.4 10 GraniteBlock

squaringSintered

11 11 6.4 10 Granite Blocksquaring

Sintered

8.5 8.5 6 9.5 Granite Profiling Sintered

8.8 8.8 6 9.5 Granite Profiling Sintered

11 11 6.4 10 Concrete Cutting Sintered

11.5 11.5 6.4 10 Concrete Cutting Sintered

Cutting parameters

(mm)

Specifications

Number

of

beads/

meter

Installation

method

Material to

cutUsage

m/sLiner

speed

Cuttingspeed

(cm/h)

(/m)Life

span



32/41

Soft marble quarrying 30-35'9-12(

/h)25-45

Medium

hard

marble

quarrying 28-32'7-10(

/h)15-2511 28 Spring

Hard

marblequarrying 26-30

'4-8(

/h)'10-20

Soft marbleBlock

squaring30-35 90-130 30-40

Medium

hard

marble

Block

squaring28-32 70-100 25-3010.5 37 Plastic

Hard

marble

Block

squaring

26-30 60-80 20-25

Soft marble Profiling 30-34 100-150 35-45

Medium

hard

marble

Profiling 28-32 80-120 25-358.5/8.8 37 Plastic

Hard

marbleProfiling 26-30 70-100 20-30

Soft granite quarrying 24-28'4-7(

/h)'10-20

Medium

hard

granite

quarrying 22-24'2-4(

/h)'8-14

Hard

granitequarrying 18-22

'1-2(

/h)'6-9

11.5/11 40 Rubber

Abrasive

granitequarrying 26-30 '4-7(

/h)'10-20

Soft graniteBlock

squaring22-26 60-100 912

Medium

hard

granite

Block

squaring20-24 4060 815

Hard

granite

Block

squaring18-22 2545 68

10.5/11 37/40 Plastic

Abrasive Block 22-26 60-100 1220



33/41

granite squaring

Soft granite Profiling 24-28 60-80 913

Medium

hard

granite

Profiling 22-26 30-60 711

Hard

graniteProfiling 20-24 20-35 58

8.5//8.8 37 Plastic

Abrasive

graniteProfiling 24-28 60-80 913

Low

intensity

concrete

Cutting 2225 25 27

Medium

intensity

concrete

Cutting 2022 12 12.510.5/11.5 40

Plastic+

Spring

Rubber+

SpringHigh

intensity

concrete

Cutting 1820 0.51 0.51.2




Comsuption(L/min)




34/41

Blade and segment for cutting stone edge and small size block

Brief Introduction: The saw blade uses high fruquency welding or laser welding, applicable for the cutting of airport raceway,

highway and building decoration. It also can be used for dismantling building with concrete,steel framework ,opening the hole for

door and window.,

characteristic of products: sharp cutting, long life, strong brazing,heat resistant, safe use and easy operation.

Other specifications and sizes are available upon request!

Diameter(mm) Segment Length(mm) Segment Width(mm) Segment Height(mm) Inner Hole(mm)

230 40 2.6 10

250 40 2.8 10

300 40 3 10

350 40 3.2 10

400 40 3.5 10

450 40 4 10

500 40 4.4 10

600 40 4.8 10

650 40 4.8 10

700 40 5.2 10

750 40 5.5 10

800 40 5.8 10

1000 24/40 6.5 10

1200 24/40 7.5 10

1400 24/40 8.5 10

1600 24/40 9.5 10

20/22.23/25.4/32/50/60




Cutting Material



35/41

Blade for manual cutting machine

Brief introduction: For cutting and nondestructive grooving on marble,granite,ceramic tile,concrete,decorative material, used on

manual cutting machine.

Characters of the products: fast cutting speed,samll cutting gap, low power consumption,sharpness,abrasiveness

Commodity Diameter(mm) Hole(mm) Size of segment Number of teeth

Segmented cutter 105 1.8*7.5 8






Segmented cutter 230 2.4*8 16



Segmented cutter 350

16/20/22.23/25.4/50

2.8*8.0 24

Turbo cutter 105 2.0*8 45


Turbo cutter 115

16/20/22.23/25.4/50

2.0*7.5 48



36/41








Turbo cutter 200 2.4*8.0 90

Turbo cutter 230 2.6*8.0 72

Turbo cutter 230 2.6*8.0 140



Continuous rim cutter 105 1.8*8






Continuous rim cutter 200 2*8





Continuous rim cutter 400

16/20/22.23/25.4/50

2.8*8

Operation notes:

1Pay attention to the joining and the rotating direction of motor shaft and hole of cutter, defected blades are forbiddened.

2Do not cut metal, or the blade will become blunt and the life span will be shortened.

3For the cutter is thin, do not put pressure on its sides or carry out curvilinear cutting, avoid tangency between edge of blade and

spare parts when it feeds.

4 Carborundum abrader, firebrick and grinding wheel are recommended in case blade cann't open

5

For safety use, blade cover is needed for the cutting machine, the operator should wear safety dressing, glasses and otherprotective articles.

6Water cooling is needed when use wet cutter, otherwise life span of cutter will be shortened.



37/41

19. Antique Brush

Frankfurt Abrasive Brush

YIDIC Abrasive Brushes Frankfurt are used in handed and automatic grinding

machine, step-retreading machine etc.Grit mesh: stainless steel, steel +36#,

36#, 46#, 60#, 80#, 120#, 180#, 240#, 320#, and 500#....



38/41

Fickert Abrasive Brush

Fickert abrasive brushes are used in granite automatic grinding line.Include

eleven filaments: stainless steel, steel+36#, 36#, 46#, 60#, 80#, 120#, 180#,

240#, 320#, and 500#....

Diam. 110mm M14 Abrasive Brush

Diam.110mm MA14 abrasive brushes are used in handed grinding machine.Include

eleven filaments: stainless steel, steel+36#, 36#, 46#, 60#, 80#, 120#, 180#,

240#, 320#, and 500#...

Diam. 200mm Round Abrasive Brush

Diam.200mm round abrasive brushes are used in stone industrial polishinglines.Include eleven filaments: stainless steel, steel+36#, 36#, 46#, 60#,

80#, 120#, 180#, 240#, 320#, and 500#....

Diam. 250mm Round Abrasive Brush

Diam.250mm Round Abrasive Brushes with Velcro back is used in automatic

grinding machine, antique stone industrial lines. Grit mesh: stainless

steel, steel+36#, 36#, 46#, 60#, 80#, 120#, 180#, 240#, 320#, and 500#. ...

Snail Lock Abrasive Brush

Snail Lock Abrasive Brushes are used in side grinding machine and step

retreading machine.Grit mesh: stainless steel, steel+36#, 36#, 46#, 60#,

80#, 120#, 180#, 240#, 320#, and 500#. ...

Diam. 110mm M16 Abrasive Brush

Diam.110mm M16 is used in handed grinding machine.Grit mesh: stainless steel,

steel +36#, 36#, 46#, 60#, 80#, 120#, 180#, 240#, 320#, and 500#....

WHAT IS OUR ABRASIVE BRUSH FOR STONE?

Our brushes adopt Dupont nylon filaments with silicon carbide grit inside. It has different kinds and grit, could fit in hand grinding

machine, industrial polishing lines .step retreading machine and hand-controlled machine and so on to deal with natural stone andartificial stone .With the most fine grit ,the surface can be polished ,get satin result ,and stone natural texture can be appeared .At

the same time ,the stone achieve antique look surface and satin repellent ability can be improved .At the same time it could improve

the antifouling and skid prevention



39/41

HOW IS PRINCIPLE OF OUR BRUSH?

When the abrasive brush is using for treating the stone, the silicon carbide grit inside can grind and polish the surface. Because of

the flexibility of the filament, under the press, the abrasive filaments can touch, grinding and polishing the all of surface even if the

surface is uneven. With the most fine grit, the surface can be polished, get satin result, and stone natural texture can appeared. At

the same time, the stone achieve antique look surface and satin repellent ability can be improved.

WHATS THE ADVANTAGE?

Our abrasive brushes adopt top quality and low density nylon, reducing the cost and enhancing the efficiency.

Our filaments show the wave shape, the polishing effect is good and long life.

Our brush could keep rigidity and tenacity in humidity circumstance.

Our brushes have the better resilience.

Our brush could keep the best life.

Logical height and density guarantee the best effect and life.

Adopting fixed the filaments in fourth directions, prevented the filaments broke off during working .Guarantee the best life of our

brush.

Our steel brushes adopt high strength and special elastic stainless steel.

The speciation is entire and is used in varied polishing and retreading machine.

Grit is entire and guarantee different grinding effect.

We could order in advance different abrasive brush according to special machine.

WHY ADOPT DUPONT PROFESSIONAL FILAMENTS?

Dupont Company invented Nylon and aggressive nylon filaments, it takes up the first place in the craft in the world.

Amount these our abrasive brush adopt TynexA which distribute different grit in the nylon 612,adopting special craft

making the filaments wave shape ,then guarantee the grinding effect and enhance the working efficiency.

WHY ADOPT NYLON 612?

Nylon 612 can retain rigidity and tenacity in humidity circumvents .With adding water ,the other kind of nylon will be

softening and loss rigidity .Nylon 6/66/610 comes from biology and petroleum polymer without consistent quality .Nylon

612 with lower bibulous and density characteristic is the best filament for abrasive brush .

WHY DOES IT ADOPT WAVE SHAPE FILAMENTS?

Strengthening the elastic of the filaments, to guarantee the best polish effect of our brush.

Make the filaments separate each other, more uniformity grinding on the stone surface.

Increasing the hardness of the filaments, improving the polish efficiency.

Decreasing the possibility of filaments broke off because of centralized, guarantee the best life of our brush.

HOW TO IDENTIFY THE QUALITY OF BRUSHES?

The filaments cannot brush off during working.

The filaments fixed to the frame with high strength stainless steel wire prevented from corrosion.

Filament should be bended wave shape.

The silicon carbide grit in the filaments shouldnt break off because of the wave shape filaments.

The appropriate height and density of the brushes.The filaments should have the good wave resilience.

The filaments should have the long life.



40/41

IS LONGER LIFE OK BY HIGHER FILAMENTS?

Not allowed, because the life of brush depends on the making craft, filaments quality and right using method.

If adding the height of the filaments unwisely ,then won t guarantee the rigidity, it will fall down during working ,so filament side over

grind and cause them thin ,then will rapture earlier and loss their life .

WHAT'S THE EFFECT FOR GRANITE AFTER GRINDING ?

The granite after grinding ,have the uneven archaized effect ,showing the nature light ,and could have the antifouling and skidprevention. wishing to get the above effect ,before the grinding it must be dealt with the flaming pan . and so on surface; first using

steel brush removing the surface and fix it ,then using the abrasive brush from thick to thin ,until to get the satisfied effect .

WHAT'S THE EFFECT FOR MARBLE AFTER GRINDING ?

Most marble could get the antique effect directly dealing with it ,showing the nature light ,and could have the antifouling and skid

prevention. As some stone before grinding ,according to need and structure ,dealing with in advance in physical methods ,then

using the grit no from thick to thin to grind it, until the pan could get the satisfied effect .

HOW MANY KINDS AND GRITS FOR THE BRUSH ?

According to the kinds ,it has Frankfurt (horseshoe),Diam 110mm round brush .Fickert (brad) and so on ;According to the grits

included steel. 36# .46#60#80#120#180#240#320#500# and so on .Frankfurt is used in hand grinding machine ,industrial

polishing lines step retreading machine ,round brush is used in hand grinding machine step retreading machine ;Fickert is used in

automatic grinding machine .

HOW TO CHOOSE VARIED KINDS OF BRUSH?

Usually ,steel and grit 36# abrasive brush is removing the surface loose and pan stereotypia; grit 46# 60# 80# for grind simply ;120#

180# 240# could polish simply ;320# 500# could polish fine ,to getting the archaized effect. If it is the first time to use the abrasive

brush ,should test in each grit ,to choose from it according to the kinds of stone and need .

HOW TO USE THE ABRASIVE BRUSH RIGHTLY?

Adding water during the grinding . Prevented the high temperature making the filaments changing shape during the

filaments friction in high speed .As the sequence of the number of abrasive brush from thick to thin ,the pressure

working on the grind should from big to small. Its logical for the skip .

Reducing the middle step excessively will affect the effect of grinding ,other size it will add the cost .Using the steel

brush as possible. The abrasive brush as the first step could reduce the loss for the rough surface to abrasive

filaments, extended the life of the abrasive brush.

WHY ADOPT LOW DENSITY FILAMENTS?

For the abrasive brush we should talk about three density ,its the filaments on the abrasive brush (craft density) the

silicon carbide grit in the filaments and nylon density as the silicon carbide (material density).the first and the second

density should have the logical ,and not much higher is much better ;and nylon density should have the basic of top

quality ,lower the density -reducing the unit weight of the filaments, reducing the cost of material.



41/41

Documents

Technical of Our Diamond Tools