Upload
others
View
6
Download
1
Embed Size (px)
Citation preview
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
1
SIGNATURE & SEAL OF TENDERER
TECHNICAL SPECIFICATION
VOLUME – II
CONTENTS
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
2
SIGNATURE & SEAL OF TENDERER
TECHNICAL SPECIFICATIONS
GENERAL
i. The detailed specifications given hereinafter are for the items of works
described in the schedule of quantities attached herein & shall be
guidance for proper execution of work to the required standards.
ii. It may also be noted that the specification are of generalized nature &
these shall be read in conjunction with the description of item in schedule
of quantities & drawings. The work also includes all minor details of
construction which are obviously & fairly intended & which may not have
been referred to in these documents but are essential for the entire
completion in accordance with standard Engineering practice.
iii. Unless specifically otherwise mentioned, all the applicable codes &
standards published by the Indian standard Institution & all other standard
which may be published by them before the date of receipt of tenders,
shall govern in all respects of dosing workmanship quality & propitious of
materials & methods of testing, method of measurements etc. Wherever
any reference to any Indian Standard specifications occurs in the
documents relating to this contract, the same shall be inclusive of all
amendments issued to or revisions thereof, if any, up to the date of receipt
of tenders.
iv. In case there is no I.S.I specification for the particular work, such work
shall be carried out in accordance with the instructions in all respects, &
requirements of the Engineers-in-Charge. Wherever any reference to any
Indian standard specification occurs in the documents relating to this
contract, the same shall be inclusive of all amendment issued there to or
revisions thereof, if any, up to the date of receipt of tenders.
v. The work shall be carried out in a manner complying in all respects with
the requirements of relevant bye-laws of the Municipal
Committee/Municipal Corporation/Development Authority/Improvement
Trust under the jurisdiction of which the work is to be executed or as
directed by the Engineer-in-Charge and, unless otherwise mentioned,
nothing extra shall be paid on this account.
vi. Samples of various materials, fitting etc. proposed to be incorporated in
the work shall be submitted by the contractor for approval of the
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
3
SIGNATURE & SEAL OF TENDERER
Engineers-in-Charge before order for bulk supply is placed.
vii. The contractor shall take instructions from the Engineer-in-Charge
regarding collection and stacking of materials in any place. No excavated
earth or building materials shall be stacked on areas where other
buildings, roads, services, compound walls etc. are to be constructed.
viii. The contractor shall maintain in perfect condition all works executed till the
completion of the entire work allotted to him. Where phased delivery is
contemplated, this provision shall apply to each Phase.
ix. The contractor shall give a performance test of the entire installation(s) as
per standard specifications before the work is finally accepted & nothing
extra whatsoever shall be payable to the contractor for the test.
x. The contractor shall clear the site thoroughly of all scaffolding materials &
rubbish etc. left out of his work & dress the site around the building to the
satisfactions & his decision in writing shall be final & binding on all
concerned.
xi. Post construction inspection and testing: After completion of the work
and during maintenance period liability of the contractor, the work shall
also be subjected to 'Post construction inspection and testing'. In case the
materials or articles incorporated in the work are found to be inferior,
though the sample collected for the same might have been passed at the
time of execution, it shall be the responsibility of the contractor to replace
the same at his own cost, failing which the Department may rectify the
same at the risk and cost of the contractor or Department may accept the
work as sub-standard, and cost be adjusted from the outstanding security
deposit, as per the terms and conditions of the contract for the work.
xii. The Dean (I.P.S.), shall be the sole deciding authority as to the meaning,
interpretations and implications for various provisions of the specifications
and his decision in writing shall be final and binding on all concerned.
xiii. In case any different or discrepancy between the specification & the
description in the schedule of quantities, the schedule of quantities shall
take precedence. In case of any difference or discrepancy between
specification & drawing, the specification shall take precedence.
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
4
SIGNATURE & SEAL OF TENDERER
2. STRUCTURAL STEEL :
2.1 SCOPE OF WORK :
The work covered by this specification consists of furnishing and erecting of
structural steel complete in strict accordance with this specifications and the
applicable drawings.
2.2 MATERIALS :
2.2.1 All structural steel shall be of standard sections as marked on the
drawings and shall be free of scale, blisters, laminations, cracked edges
and defects of any sort. If the structural steel is not supplied by the
Department and the Contractor is required to bring such steel, the Contractor
shall furnish duplicate copies of all mill orders and/ or also the test report
received from the mills, to satisfy the Engineer-in-Charge.
2.2.2 All structural steel and electrodes shall comply in all respects with I.S.S.
for structural steel.
2.3 WORKMANSHIP :
All workmanship shall be of first class quality in every respect to the greatest
accuracy being observed to ensure that all parts will fit together properly on
erection.
All ends shall be cut true to planes. They must fit the abutting surfaces closely.
All stiffeners shall be fit tightly at both ends.
All butt ends of compression members shall be in close contact through the
area of the joints.
All holes in plates and section between 12 mm. and 20 mm. thick shall be
punched to such diameter that 3 mm. of metal is left all around the hole to be
cleaned out to correct size by reamer.
The base connection shall be provided as shown on drawings and the greatest
accuracy of workmanship shall be ensured to provide the best connections.
Figured dimensions on the drawings shall be taken.
2.4 ERECTION AND MARKING :
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
5
SIGNATURE & SEAL OF TENDERER
Erection and fabrication shall be according to I.S. 800-1984 section-11. During
erection, the work shall be securely braced and fastened temporarily to provide
safety for all erection stresses etc. No permanent welding shall be done until
proper alignment has been obtained.
Any part which do not fit accurately or which are not in accordance with the
drawings and specifications shall be liable to rejection and if rejected, shall be at
once be made good.
Engineer-in-Charge shall have full liberty at all reasonable times to enter the
contractors premises for the purpose of inspecting the work and no work shall be
taken down, painted or despatched until it has been inspected and passed. The
contractor shall supply free of charge all labour and tools required for testing of
work.
2.5 DELIVERY AT SITE :
The contractor shall deliver the component parts of the steel work in an
undamaged state at the site of the works and the Engineer-in-Charge shall be
entitled to refuse acceptance of any portion which has been bent or other wise
damaged before actual delivery on work.
2.6 SHOP DRAWINGS :
The shop drawings of structural steel based on contract drawings shall be
submitted to the Engineer-in-Charge. The necessary information for fabrication,
erection, painting of structure etc. must be furnished immediately after
acceptance of the tender.
2.7 PAINTING :
Painting should be strictly according to I.S. 1477-1971 (PartI-Pretreatment) and
I.S. 1477-1 971 (Part II-painting).
Painting should be carried out on dry surfaces free from dust, scale etc. The
paint shall be approved by the Engineer-in-Charge.
One coat of shop paint (red lead) shall be applied on steel, except where it is to
be encased in concrete or where surfaces are to be field welded.
2.8 WELDING :
Welding shall be in accordance with I.S. 816-1969, I.S. 819-1957, I.S. 1024-
1979, I.S. 1261-1959, I.S. 1323-1982 and I.S. 9595-1980 as appropriate. For
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
6
SIGNATURE & SEAL OF TENDERER
welding of any particular type of joint, welders shall give evidence of having
satisfactory completed appropriate tests as described in any of I.S. 817-1966,
I.S. 1393-1961, I.S. 7307 (Part-I)-1 974, I.S. 7310 (Part-I)-1974 and I.S. 7318
(Part-I)-1 974 as relevant.
2.8.1 Welding Consumables : Covered electrodes shall conform to I.S.
814 (Part-I)-1974 and I.S.814 (Part-II)-1974 or I.S. 1395-1 982 as
appropriate.
Filler rods and wires for gas welding shall conform to I.S. 1278-1972.
The bare wire electrodes for submerged arc welding shall conform to I.S.
7280-1 974. The combination of arc and flash shall satisfy the requirements
of I.S. 3613-1 974.
The filler rods and bare electrodes for gas shielded metal, arc welding shall
conform to I.S. 6419-1971 and I.S. 6560-1972 as appropriate.
2.8.2 Types of Welding: Arc welding (direct or alternating current) or
Oxyacetylene welding may be used. Field welding may be used. Field
welding shall be by D.C.
2.8.3 Size of Electrode Runs: The maximum gauge of the electrodes for
welding any work and the size of run shall be based on the following tables.
Average thickness of plate
or section
Maximum gauge or diameter of
electrodes to be used. Less than 3/16" 10 S.W.G.
3/16" and above but less than 8 S.W.G.
5/16" and above but less than 6 S.W.G.
3/8" and above but less than 4 S.W.G.
5/8" and above but less than 1" 5/1 6"dia.
1" and above thick section 3/8" dia.
Note : On any straight weld the first run shall not ordinarily be deposited with
a larger gauge electrode than No. 8 S.W.G. For subsequent runs the
electrode shall not be increased by more than two electrode size between
consecutive runs.
2.8.4 Welding Contractors : The contractor shall ensure that each
welding operator employed on fabrication or erection is an efficient and
dependable welder, who has passed qualifying tests on the types of welds
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
7
SIGNATURE & SEAL OF TENDERER
which will be called upon to make. Sample test shall have to be given by
the contractor to the entire satisfaction of the Engineer-in-charge.
2.8.5 Welding Procedure :
a) Welding should be done with the structural steel in flat position in a
down hand manner wherever possible. Adequate steps shall be taken to
maintain the correct arc length, rate of travel, current and polarity for the type of
electrode and nature of work. Welding plant capacity shall be adequate to carry
out the welding procedure laid down. Adequate means of measuring the current
shall be available either as a part of the welding plant or by the provision of a
portable ammeter. In checking the welding current, a tolerance of 10% or 30
amperes from the specified value whichever is less shall be permitted.
b) The welding procedure shall be such as to ensure that the weld metal
can be fully and satisfactory deposited through the length and thickness of all
joints so that distortion and shrinkage stresses are reduced to the minimum and
thickness of welds meet the requirements of quality specified.
2.9 WORKMANSHIP :
2.9.1 Preparation of Fusion Faces : Fusion faces shall be cut by stearing
machine or gas cutting and later dressed by filling or grinding so that they
shall be free from irregularities such as would interfere with the deposition
of the specified size of weld to cause the defects. Fusion faces and the
surrounding surfaces shall be free from heavy slag, oil paint or any
substance which might affect the quality of the weld or impede the progress
of welding. The welding face shall be free of rust and shall have metal shine
surfaces.
The parts to be welded shall be brought into as close contact as possible and
the gap due to faulty workmanship or incorrect fit up shall not exceed 1/16".
If separation of 1/16" or more occurs locally, the size of the fillet weld shall
be increased at such position by an amount of equal to the width of the gap.
The parts to be welded shall be maintained to their correct position during
welding. They shall be securely held in position by means of tack welds,
service bolts, clamps or rings before commencing welding so as to prevent
and relative movement due to distortion, wind or any other cause.
2.9.2 Step Back Method Should be Used to Avoid Distortion : The
minimum leg length of a fillet weld as deposited should not be less than the
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
8
SIGNATURE & SEAL OF TENDERER
specified size and the throat thickness as deposited should be not less than
that tabulated below:
Throat Thickness of Fillet
Angle between fusion
faces
600-900 910-
1000
1010-
1060
1070-
1130
1140-
1200 Throat thickness in
cms.
0.70 0.65 0.60 0.55 0.50
In no case should a concave weld be deposited without the specific approval
of the Engineer-in-Charge unless the leg length is increased above the
specified length so that the resultant throat thickness is as great as would
have been obtained by the deposition of a flat.
All welds shall be deposited in a pre-arranged order and sequence taking
due account of the effects of distortion and shrinkage stresses.
After making each run of welding, all slag shall be removed and final run
shall be protected by clean boiled linseed oil till approved.
The weld metal, as deposited, shall be free from crack, slag,excessive
porosity, cavities and other faults.
The weld metal shall be properly fused with the parent metal without
overlapping or serious undercutting at the toes of the weld.
The surfaces of the weld shall have a uniform and consistent contour and
regular appearance.
In welds containing crack, porosity or cavities in which the weld metal tends
to overlap on the parent metal without proper fusion, the defective portions
of the welds shall be out cut and re-welded. Where serious under cutting
occurs, additional weld metal shall be deposited to make good reduction.
Testing of welded joints shall be done as per relevant IS codes 3600, 3613,
4260, 7205, 7215, 7307, 7310, 7318.
2.10 MODE OF MEASUREMENT:
All structural steel shall be measured on weight basis in metric tonnes or
quintals or kgs. as mentioned in the schedule of quantities. The length or areas
of various members including gusset plates shall be measured correct to two
places of decimals and the net weight worked out from the standard steel tables
approved by Indian Standard Institution. No separate measurements shall be
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
9
SIGNATURE & SEAL OF TENDERER
taken for welding, riveting, bolting, field connections etc. The rate shall include
cost of all labour, materials, scaffolding, transport and also cost of welding,
riveting and bolting, field connections if any all to complete the job as per
specifications.
* * * *
3. PAINTING :
3.1 SCOPE OF WORK :
The work covered under these specifications consist of furnishing the
various types of paints and also the workmanship for these items, in strict
compliance with these specifications, which are given in detail here-in-after with
the item of schedule of quantities.
3.2 MATERIALS :
Paints, oils, varnishes etc. of approved brand and manufacture shall be
used. Ready mixed paints as received from the manufacturer without any
admixture shall be used.
If for any reason, thinning is necessary in case of ready mixed paint, the
brand of thinner recommended by the manufacturer or as instructed by the
Engineer-in-Charge shall be used. Approved paints, oils or varnishes shall be
brought to the site of work by the contractor in their original containers in sealed
condition. The materials shall be brought in at a time in adequate quantities to
suffice for the whole work or atleast a fortnights work. The materials shall be
kept in the joint custody of the contractor and the Engineer-in-charge. The
empties shall not be removed from the site of work, till the relevant item of work
has been completed and permission obtained from the Engineerin-Charge.
The contractor shall associate the chemist of paint manufacturers before
commencement of work, during and after the completion of work who shall
certify the suitability of the surface to receive painting and the paint before use
etc.
3.3 COMMENCING WORK :
Scaffolding : Wherever scaffolding is necessary, it shall be erected on
double supports tied together by horizontal pieces, over which scaffolding
planks shall be fixed. No ballies, bamboos or planks shall rest on or touch the
surface which is being painted.
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
10
SIGNATURE & SEAL OF TENDERER
Where ladders are used, pieces of old gunny bags shall be tied on their
tops to avoid damage or scratches to walls.
For painting of the ceiling, proper stage scaffolding shall be erected.
Painting shall not be started until and unless the Engineer-in-Charge has
inspected the items of work to be painted, satisfied himself about their proper
quality and given his approval to commence the painting work.
Painting, except the priming coat, shall generally be taken in hand after all
other builders work, practically finished.
The rooms should be thoroughly swept out and the entire building cleaned
up at least one day in advance of the paint work being started.
3.4 PREPARATION OF SURFACE :
The surface shall be thoroughly cleaned. All dirt, rust, scales, smoke and
grease shall be thoroughly removed before painting is started. Minor patches if
any in plastered/form finished surfaces shall be repaired and finished in line
and level in C.M. 1:1 and cracks & crevices shall be filled with approved filler,
by the contractor at no extra cost to the Department. The prepared surface shall
have received the approval of the Engineer-in-Charge after inspection, before
painting is commenced.
3.5 APPLICATION :
Before pouring into smaller containers for use, the paint shall be stirred
thoroughly in its containers. When applying also, the paint shall be continuously
stirred in the smaller containers so that consistency is kept uniform.
The external surfaces of the buildings under reference including the R.C.C.
Jalli, fins and the panels above and below the window etc. shall be finished in
different colours of approved shade. The contractor will make suitable samples
at site for Departments approvel before taking up the work in hand and they will
be allowed to proceed with the work only after getting Departments approval for
the same.
The painting shall be laid on evenly and smoothly by means of crossing and
laying off, the later in the direction of the grain in case of wood. The crossing &
laying off consists of covering the area with paint, brushing the surface hard for
the first time and then brushing alternately in opposite directions two or three
time and then finally brushing lightly in direction at right angles to the same. In
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
11
SIGNATURE & SEAL OF TENDERER
this process, no brush marks shall be left after the laying off is finished. The full
process of crossing and laying will constitute one coat.
Where so stipulated, the painting shall be done with spraying. Spray
machine used may be (a) a high pressure (small air aperture) type or (b) a low
pressure (large air gap) type, depending on the nature and location of work to
be carried out. Skilled and experienced workmen shall be employed for this
class of work. Paints used shall be brought to the requisite consistency by
adding a suitable thinner. Spraying should be done only when dry condition
prevails.
Each coat shall be allowed to dry out thoroughly and rubbed smooth before
the next coat is applied. This should be fecilitated by thorough ventilation.
Each coat except the last coat, shall be lightly rubbed down with sand paper
or fine pumice stone and cleaned of dust before the next coat is laid.
No left over paint shall be put back into the stock tins. When not in use,
containers shall be kept properly closed.
The final painted surface shall present a uniform appearance and no streaks,
blisters, hair marks from the brush or clogging of paint puddles in the corners of
panels, angles of mouldings etc. shall be left on the work.
In case of cement based paints/primers, the absorbent surfaces shall be
evenly damped so as to give even suction. In any weather, freshly painted
surfaces shall be kept damp for atleast two days.
In painting doors and windows, the putty around the glass panes must also
be painted, but care must be taken to see that no paint stains etc. are left on the
glass. Tops of shutters and surfaces in similar hidden locations shall not be left
out while painting. Perspect covers of electrical switch boxes have to be painted
from inside by removing them. Care shall be taken while removing them in
position after painting with respective approved paints. In painting steel work,
special care shall be taken while painting over bolts, nuts, rivets, overlaps etc.
The additional specifications for primer and other coats of paints shall be as
in accordance to the detailed specifications under the respective headings.
Any damage caused during painting work to the existing works/surfaces
shall be made good by the contractor at his own cost.
3.6 BRUSHES AND CONTAINERS :
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
12
SIGNATURE & SEAL OF TENDERER
After work, the brushes shall be completely cleaned off paint and linseed oil
by rinsing with turpentine. A brush in which paint has dried up is ruined and shall
on no account be used for painting work. The containers, when not in use, shall
be closed, kept air tight and shall be kept at a place free from dust. When the
paint has been used, the containers shall be washed with turpentine and wiped
dry with soft clean cloth, so that they are clean & can be used again.
3.7 MEASUREMENT :
a) Painting, unless otherwise stated shall be measured by area in square
metre. Length and breadth shall be measured correct upto two places of
decimal of a metre.
b) No deduction shall be made for opening not exceeding 0.05 sqm. and no
addition shall be made for painting to the beading, moulding edges, jambs,
soffits, sils, architraves etc. of such openings.
c) In measuring painting, varnishing, oiling etc. of joinery and steel work
etc., the co-efficients as in the following table shall be used to obtain the areas
payable. The co-efficients shall be applied to the areas measured flat and not
girthed in all cases.
d) In case of painting of door shutter with push plates in plastic laminate,
deduction will be made for area of such laminations.
3.7.1 Table of multiplying Co-efficients to be applied over areas of different
surfaces to get equivalent plain areas is given in the Appendix-“C-2” of this book.
3.7.2 Explanatory notes on the table of Co-efficients.
1. Where doors, window etc. are of composite types other than those
included in para 47.7 (c), the different portions shall be measured separately
with their appropriate co-efficients, the centre line of the common rail being
taken as the dividing line between the two portions.
2. Measurements for doors, windows etc. shall be taken flat (and not
girthed) over all including chowkhats or frames, where provided. Where
chowkhats or frames are not provided, the shutter measurements shall be
taken.
3. Collapsible gates shall be measured for width from outside to outside of
gate in its expanded position and for height from bottom to top of channel
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
13
SIGNATURE & SEAL OF TENDERER
verticals. No separate measurements shall be taken for the top and bottom
guide, rails, rollers, fittings etc.
4. Rolling shutters of interlocked laths shall be measured for the actual
shutter width and the height from bottom of opening to the centre of the shaft. No
separate measurements shall be taken for painting guides and other exposed
features within or outside the shutter area. The painting of top cover or hood
shall however be measured separately.
5. Co-efficients for sliding doors shall be the same as for normal types of
doors as mentioned in the table. Measurements shall be taken outside of
shutters, and no separate measurements shall be taken for painting guides,
rollers, fittings etc.
6. Measurement of painting of doors, windows, collapsible gates, rolling
shutters etc. as above shall be deemed to include painting all iron fittings in the
same or different shade for which no extra will be paid.
7. The measurements as above shall be deemed to include also the
painting of edges, blocks, cleats etc. for which no extra will be paid.
8. The co-efficients for doors and windows shall apply irrespective of the
size of frames and shutter members.
9. When the two faces of a door, window etc. are to be treated with different
specified finishes, measurable under separate items, the edges of frames and
shutters shall be treated with the one or the other type of finish as ordered by
the Engineer-in-Charge, and measurement of this will be deemed to be
included in the measurement of the face treated with that finish.
10. In the case where shutters are fixed on both faces of the frames,
the measurements for the door frame and shutter on one face shall be taken in
the manner already described, while the additional shutter on the other face will
be measured for the shutter area only excluding the frame.
11. Where shutters are provided with clearance at top or/and bottom,
such openings shall be deducted from the over all measurements and relevant
co-efficients shall be applied to obtain the area payable.
12. In case of trellis (or jaffri) work, the measurements shall include
the painting of the frame member for which no separate measurements shall be
taken. Trellis door or window shutters shall also be measured under terllis work.
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
14
SIGNATURE & SEAL OF TENDERER
13. Wherever air conditioning grill, lighting, fixtures etc. in false ceiling
are painted along with, measurements shall be taken over all without
deductions for opening in grills and no extra shall be paid for the grills. If grills,
fixtures etc. are not painted, area of fixtures or grills as measured flat (not
girthed) shall be deducted when it exceeds 0.05 sqm. individuals. Where walls
and ceilings are painted in separate colours, the junctions of two paints shall be
brought down on the walls in a straight line by about 6mm.to 12mm. if so
desired, if the junctions of walls and ceilings are not even. Nothing extra shall
be paid to the contractor on this account. Beading wherever provided shall not
be measured separately but shall be deemed to be included in the area of false
ceiling etc. measured flat (not girthed).
14. For painting open palisade fencing and gates etc., the height shall
be measured from the bottom of the lowest rail, if the palisades do not go below
it, (or from the lower end of the palisades, if they project below the lowest rail),
upto the top of rails or palisades whichever are higher, but not up to the top of
standards when the latter are higher than the top rails or palisades.
15. In the case of asbestos cement corrugated or semi-corrugated
sheeting and iron corrugated sheeting in roofs, side cladding etc., the work
shall be measured flat (not girthed) as fixed.
16. For trusses, compound girders, stanchions, lattice girder and
similar work, actual areas will be measured in sqm. and no extra shall be paid
for painting on bolt heads, nuts, washers etc. even when they are picked out in
a different tint to the adjacent work.
17. Painting of rain water, soil, waste, vent and water pipes etc. shall
be measured in running metres of the particular diameter of the pipe concerned.
Painting of specials such as bends, heads, branches, junctions, shoes etc. shall
be included in the length and no separate measurements shall be taken for these
or for painting brackets, clamps etc.
18. Measurements of wall surfaces and wood and other works not
referred to already shall be recorded as per actual and opening exceeding 0.05
sqm. shall be deducted to get the net payable area. Length and breadth shall be
measured correct upto two places of decimal of a metre and area so worked out
shall be correct upto two places of decimal of a square metre.
19. In case the items of work requiring painting are inclusive of cost of
painting, the painting carried out shall not be measured separately.
3.8 PRECAUTIONS :
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
15
SIGNATURE & SEAL OF TENDERER
All furnitures, lightings, fixtures, sanitary fittings, glazing, floors etc. shall be
protected by covering and stains, smears, splashings, if any shall be removed
and any damage done shall be made good by the contractor at his cost.
3.9 RATES:
Rates shall include cost of all labour and materials involved on all the
operations described above and in the particular specifications given under the
several items.
GENERAL METAL SPECIFICATIONS
STAINLESS STEEL:
Where stainless steel is specified it shall be what is known to the trade as Austenitic 18-B
type 304, 2B finish, with content from 17% to 19% chrome, 7 % to 9% nickel and a maximum
carbon content of 0.11. A certificate with the batch number is to made available from the
supplier and a copy to be made available upon request
tainless steel shall be free from scale and surfaces should be polished to a no.4 commercial
inish.
A Swatch of the finish to be submitted to the Institute (IIT-B) upon receipt of order.
STAINLESS STEEL PIPE AND TUBING:
Seamless tubing shall be thoroughly and properly ground smooth and finished to match
adjacent work. All tubing where exposed to view shall be given a final grand of not less then
180 grit emery.
STRUCTURAL STEEL SHAPES:
All angles, band, channels or other structural shapes used for framing shall be of domestic
manufacture uniform and ductile in quality, free of hard spots, runs, checks or cracks or other
surface defects.
HANDLES, BRACKETS, LOCKING DEVICES AND HARD WARE:
Wherever equipments are provided with handles, knobs, hinges, brackets or other misc.
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
16
SIGNATURE & SEAL OF TENDERER
hardware all shall be either of heavy stain finish chrome plated brass or stainless steel.
All drawers, enclosed cabinets, refrigerators storage bins, shall be furnished with extra heavy
duty security type locking devices of cylinder type, chrome plated.
FASTENINGS:
Welds, bolts screws, nuts and washers shall be of stainless steel, except where brass or
stainless steel is fastened, in which case they shall be of brass or stainless steel respectively.
Where dis-similar metals are fastened, bolts, screws and nuts shall be of the highest grade
metal. The spacing and extent of welds, bolts and screws shall be such as to ensure suitable
fastenings and prevent bulging of the material fastened.
WELDING:
All welding shall be done by the electrical fusion, metal –arc method. Carbon-arc or gas
welding will not be permitted. All welding shall be done in a thorough manner, with welding
rod of some composition as sheets or parts welded. Welds shall be complete welds, strong
and ductile, with excess metal ground off joints finished smooth to match adjoining sheet
Surfaces. All joints in top of fixtures, tables, drain boards; exposed shelving, sinks etc. shall
be welded. All equipment here in specified which is constructed in more then one piece of
sheet of metal, shall be continuously welded together with welds ground smooth and
polished. But welds made by spot welding straps under beams and filling in the voids with
solder and finished by grinding will not be accepted.
It is the intention of this specification that all welded joints shall be homogenous with the
sheet metal itself. Where sheet sizes necessitate a joint, such a joint shall be welded. Tops of
fixtures shall be fabricated in the factory with welded joints to reduce field joints to a
minimum, where fixtures joins the tops of such fixtures shall be continuous with welded joints
except in the case of field joints. A joints made in the field shall be closely butted, pulled
together in the field, field welded and polished smooth in accordance with section. Grinding,
polishing finishing if these requirements. Tops of fixtures shall be of maximum length and with
welded factory joints to an absolute minimum. Wherever welds occur on the surfaces not
finished by grinding & polishing, such welds sand the accompanying discoloration shall be
suitably coated in the factory by means of metallic base paint. To prevent the possibility of
progressive corrosion of such joints.
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
17
SIGNATURE & SEAL OF TENDERER
GRINDING, POLISHING, FINISHING:
All welded exposed joints shall be suitably ground flush with adjoining material and neatly finish
harmonizing herewith. Wherever material has been sunken or depressed by the welding operation,
such depression will be suitably hammered and pressed flush to adjoining surfaces and if
necessary again ground to eliminate low spots. All ground surfaces shall then be polished or
buffed to match adjoining surfaces, consistent with good workmanship. Care shall be exercised in
all grinding operations to avoid excessive heating of metal & metal discoloration. In all cases, grain
of rough grinding shall be removed by successive polishing operations. Texture of final polishing
operation shall be uniform and smooth consistent with reasonable care and good workmanship.
General finish of all equipment shall be of high grade.
But joints and contact joints, wherever they occur, shall be close fitting and shall not require solder
as filler. In no case in any Soldering for strength and stability of joint and fixture itself. Wherever
breaks bend occur, it shall be free from undue extrude and shall not be flaky scaly or cracked in
appearance and where such break work does mar the uniform surface appearance of the material.
All such marks shall be removed by suitably grinding, polishing and finishing. Wherever shared
edges occur they shall be free from burrs, fins or irregular projections and shall be finished over
such sheared edges. Where miters are bull nosed corners occur they shall be neatly finished with
under edge of material neatly ground to a uniform condition and, in no case any over lapping
materials shall be accepted.
It is the intention of these specifications to cover equipment of quality finish consistent with
high grade manufacturing practices. All exposed surfaces shall be of no 4 finish expected trim,
which is to be more highly polished satin finish. Where specified all doors cabinets, shelves,
whether inside /outside of cabinets and wherever exposed are to be no. four 4 finish. This applies
to inside finish of any cabinet having doors or otherwise an exposed surface shall be interpreted as
meaning an inside surface exposed to view when a sliding or swinging door is opened. Underside
of shelf need not to be 4 finishes but such finish shall be at least equal to 80- ground finish. Final
no. 4 finishes being factory finish, not as furnished by mill. Indication of die markings not
blending with final finish will not be accepted.
BOLT CONSTRUCTION:
It is the intention of this specification that all equipment on exposed surfaces and wherever bolts
are used to fasten trim to paneling and body of warmers, cabinets, counters etc. and more
particularly to fasten tops of counter, dish tables etc. to top of framing such bolts and screws occur
on the inside of the fixtures and are either visible or might come in the contact of the hands or the
wiping cloth, such bolts, screws shall be capped with a suitable lock washer and chrome plated,
brass or bronze acorn nut . Where screw nuts are not visible or readily accessible, they may be
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
18
SIGNATURE & SEAL OF TENDERER
capped with a standard lock washer & steel nut treated to prevent rusting & corroding. Wherever
bolts and screws are welded to underside of trim or tops, the reverse side of weld shall be neatly
finished uniform with the adjoining surface of trim or top, depressions at these points will not be
acceptable.
SOUND DEADENING:
Underside of all stainless steel top for tables, counters, sink dishes and pot table with angle
framework shall be treated with a coating of Carbonize aluminium finish or approved alternate by
The Engineer-in-charge IIT-B,
MATERIAL AND WORKMANSHIP:
All material equipment etc. shall be new and of kind specified and shall be in undamaged condition
when turned over to IIT-B. All workmanship shall be of best quality of crafts men skilled in their
respective trades. Appliances shall be of rigid construction free from objectionable vibrations and
quiet in operation. Manufacture’s nameplate shall not appear on any of the fabricated equipment.
Cold Room Accessories :
The Cold room and freezer shall be complete with all materials and accessories for the function
and safe use of the cold room. It shall include lighting, control panel, safety features.
The Cold room/Freezer shall be installed along with the Kota Flooring and is within the
scope of the Cold room vendor.
RESERVATIONS:
Various items are specified here in with the model no., brand or trade names or
name of manufacturer, and it is the intent of this specification that the exact
fixture so specified shall be furnished. This is not intended to restrict competition
and consideration will be given to other brands that are equal or superior on
every respect, due written approval will have to be obtained from the
institute/consultant prior to its submission. However no substitutes or
alternatives will be accepted if not mentioned in the base bid.
IIT-B reserve right to waive any information or reject any or all bids or any part or parts
thereof, or to accept that bid as a whole or part, which in his judgment.
The decision as to acceptance or rejection of any alternate proposed shall be that of IIT-
B and / or architect or his consultant and their decision shall be final.
LEGS:
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
19
SIGNATURE & SEAL OF TENDERER
All legs to be constructed of not less than 38 mm dia / 30x30 square stainless steel
pipes( as specified and indicated in individual equipment illustration), cold drawn,
annealed and pickled spaced not more than 1800mm C.C., all legs shall be uniform in
finish. All legs, to be of 304 SS.
LEGS CROSS BRACING:
All legs bracing where required, to be constructed of not less than 25 mm diameter /
25x25 mm square, 18GA SS pipes and as specified above for expect as noted below.
All cross bracing to run horizontal between all legs, approximately 150 mm above floor
unless otherwise specified. All joints to be completely welded around entire perimeter
forming complete seal with all welds ground and painted. Where one side of box unit is
eliminated to provide space for cans, carts, plumbing or otherwise single cross brace to
extent to given legs, such cross brace to be reinforced by diagonal section of tubing and
set not less then 150mm out at each side, all welded as specified herein before.
UNDER BRACING:
All stainless steel counters, tables boards and dish tables tops to be braced below with
stainless steel angle framework made of 35x35x3mm/5mm thick (or as specified in
individual equipment illustration), spaced not more than 750 mm on centers and
installed in similar fashion.
FEET:
All legs shall be provided with adjustable nylon bullet feet, having an integrally formed
shaft, with a minimum adjustment of appox. 40mm without using of threading or
adjusting bolts. Feet shall be completely sealed at bottom and shall be close fitting
between legs support and foot.
UNDERSHELVES:
Where flat under shelving is specified under shelves shall be constructed of 18 GA SS
All shelving shall be turned down on all sides appox. 40mm and in 12mm in channel
shape with resulting corners cut out to fit contour of leg. Shelving shall be welded to
legs and shall be ground polished & smooth under shelving shall be reinforced with
35x35x3mm/5mm thick (or as specified in individual equipment illustration), 16GA SS
welded angles. Removable type shelving to be of same material, rolled down on all
sides with corners notched to counter of leg with resultant notches ground and polished
smooth. Under shelving to be constructed in sections of not more than 900 mm and
where butted against adjoining shelf section shelving to be turned down 40 mm and in
12 mm in channel shape. Supporting channel/framework to be furnished on underside
of each self-section of same size and material as specified above.
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
20
SIGNATURE & SEAL OF TENDERER
COLD ROOM SPECIFICATION
Basis of Design and Technical details
ITEM NO ROOM SIZES
CRR1 Walk-in Cold Room Size ; External 3510x3250x2750mm. Ht.
Temperature ( + 2 to + 8 deg C ) Product In Coming temperature ( +18 to 20 deg C ) Product to be stored Food Product Incoming Rate Average Ambient Temp : 40 deg C +/- 2 deg C Pull down time 24 Hours Insulation Prefab Panels Insulation thickness 60 mm
Panel Finish 0.5 mm SS inside and outside. 304 quality 18/8 grade
Density : 40 KG/ CUM
Flooring PUF slab plus Kota on top (Civil work inclusive)
Door Type
Swing type with auto closing and safety opening
Door Size 34 " x 78 " - Opening Refrigeration units Split Type Refrigeration machines: 2 hp MT - 2 nos
Compressor Hermetic - Copeland make or equivalent
Refrigerant R 22. Compressor Run time 18 to 20 hours Temperature indicator Digital type Electric 3KW/I Ph /220V .
: INCLUDE - All accessories like light switch, temperature Indicator slots on the control panel.
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
21
SIGNATURE & SEAL OF TENDERER
Corner Panels, Floor & Wall panels with Cam locks and Tongue & groove arrangement for better alignment.
FREEZER ROOM SPECIFICATION
Basis of Design and Technical details
ITEM NO ROOM SIZES
CRF1
Walk-in Freezer - Sizes : External 2100x3250x2750mm. Ht
Cold Room temperature ( - 18 deg C to - 23 deg C ) Product In Coming temperature ( - 6 deg C ) Product to be stored Food Product Incoming Rate Average Ambient Temp : 40 deg C +/- 2 deg C Pull down time 24 Hours Insulation Prefab Panels Insulation thickness 100 mm
Panel Finish 0.5 mm SS inside and outside.304 quality 18/8 grade
Density : 40 KG/ CUM
Flooring PUF slab plus Kota on top (Civil work inclusive)
Door Type Swing type with auto closing and safety opening
Door Size 34 " x 78 " - Opening Refrigeration units Split Type Refrigeration machines: 3 hp LT - 1no
Compressor Hermetic - Copeland make or equivalent
Refrigerant R 404 A Compressor Run time 18 to 20 hours Temperature indicator Digital type Electric 4.5 Kw /III Ph/440V
: INCLUDE - All accessories like light switch, temperature Indicator slots on the control panel.
Corner Panels, Floor & Wall panels with Cam locks and Tongue & groove arrangement for better alignment.
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
22
SIGNATURE & SEAL OF TENDERER
General 15.1 The Contractor shall physically check the dimensions at site and prepare and submit the shop drawing for approval immediately before executing the work. 15.2 SHOP DRAWINGS
The Contractor shall submit three (3) complete sets of detailed working and shop drawings and schedules of all work. Fabrication shall not commence until (1) set of the shop drawings has been returned to the Contractor and stamped by the Engineer as approved for fabrication.
No other substitutions in sizes or shapes of members shall be made without prior approval and no variation to the details shown on the shop drawings shall be made unless authorised by the Consultant. Minor details not shown on the drawings shall conform to the relevant Indian code and to the approval of the Consultant.
15.3 Cutting
Cutting shall be affected by shearing, cropping, sawing or gas cutting and shall be reasonably square and free from distortion with all burrs removed. If directed by the Consultant the edges shall be ground afterwards.
For gas cutting high tensile steel, sufficient metal shall be left beyond the required profile so that all metal that has been flame hardened cube removed later by machining. Except where the material is subsequently joined by welding, no load-transmitting surface shall be gas cut.
Plates in built-up members shall be end and edge planed, except where flats with square edges are used. Plates specified to be planed, milled or chipped, shall be cut in the first instance to such size as to allow 3 mm to be planed, milled or chipped, from the sides and ends. Edges of gussets up to and including 8 mm in thickness may be sheared in a machine, which can take the full side in one cut. Planning, milling or grinding shall prepare edges of gussets of greater thickness.
Edge preparation for surfaces to be welded shall be carried out by grinding planning but not shearing or cropping.
15.4 Drilling and Punching
a) Holes through more than one thickness of material for members, such as compound stanchion and girder flanges shall be drilled after the members are assembled and tightly clamped or bolted together. Punching may be permitted before assembly, provided the holes are punched 3 mm less in diameter than the required size and reamed, after assembly, to the full diameter. The thickness of material punched shall be not greater than 16 mm.
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
23
SIGNATURE & SEAL OF TENDERER
b) Drilled or reamed holes shall be cylindrical and perpendicular to the surface. They shall not be more than 1.5 mm larger than the specified diameter of bolts up to and including 25 mm in diameter.
c) When holes are drilled in one operation through two or more separable parts, these parts, when so specified by the Consultant, shall be separated after drilling and the burrs removed.
d) Holes in connecting angles and plates, other than splices, roof members and light framing, may be punched full size though material not over 13 mm thick, except where required for close tolerance or barrel bolts.
e) Matching holes for bolts shall register with each other so that a gauge of 1.5 mm or 2.0 mm (as the case may be, depending on whether the diameter of the bolt is less than or more than 25 mm) less in diameter than the diameter of the hole will pass freely though the assembled members in the direction at right angle to such members. Finished holes shall be not more than 1.5 mm or 2.0 mm (as the case may be) in diameter larger than the diameter of the rivet or black bolt passing through them, unless otherwise specified by the Consultant.
f) Holes for turned and fitted bolts shall be drilled to a diameter equal to the nominal diameter of the shank or barrel subject to H8 tolerance specified in IS: 919-1959 Recommendations for Limits and Fits for Engineering. Preferably, parts to be connected with close tolerance or barrel bolts shall be firmly held together by tacking bolts on clamps and the holes drilled through all the thickness at one operation and subsequently reamed to size. All holes not drilled through all thickness at one operation shall be drilled to a smaller size and reamed out after assembly. Where this is not practicable, the parts shall drilled and reamed separately through hard bushed steel jigs.
g) A gas cutting process shall not form holes for bolts.
h) All holes shall be free of burrs, fins and other defects
i) No holes shall be drilled in structural members at locations other than those indicated on the drawings unless approved in writing by the Consultant.
15.5 Assembly
The component parts shall be assembled in such a manner that they are neither twisted, bend nor otherwise damaged, and shall be prepared that the specified cambers, if any, are provided.
16 Bolts, Pins, Nuts and Washers
16.1 General
All bolts shall be of such a length that at least one full thread but not more than 12mm of the threaded part of the bolt is exposed beyond the nut, after the nut has been tightened. Bolts shall comply with IS: 281 and IS: 3757.
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
24
SIGNATURE & SEAL OF TENDERER
All bolts shall be fitted with one washer under the nut. Where a nut or bolt bears on an inclined surface, a leveled washer of the correct shape shall be used between the surfaces. Where necessary, washers shall be tapered or otherwise suitably shaped to give the heads and nuts of bolts a satisfactory bearing.
Bevelled washers shall not be allowed to move out of their correct positions during fabrication and erection. No connection shall be made with less than two bolts and both shall be not less than 16 mm diameter, unless otherwise indicated on the drawing.
In all cases where the full bearing area of the bolt is to be developed, the bolt shall be provided with a washer of sufficient thickness under the nut to avoid any threaded portion of the bolt being within the thickness of the parts bolted together.
16.2 Bolt Tightening
Bolts shall be "snug tightened" as defined as the tightness attained by a few impacts of an impact wrench or by the full effort of a man using a standard podgier spanner
Snug tightening shall be achieved by using a standard wrench to ensure intimate positive contact between mating surfaces. Bolts, nuts and washers that are snug tightened shall be hot dipped galvanized and centrifugally spun to remove excess spelt
17.0 WELDING
17.1 Welding Steel
a) All welders to be employed on the works shall be qualified to an appropriate standard as per the procedures outlined in the relevant Indian Standard. Testing of all welders shall be carried out before any work is commenced. Only Welders who pass the test shall be permitted to work only for those positions for which they were tested and passed.
b) Welding shall be in according with the following Indian Standards as applicable.
IS 816-1969 Code of Practice for use of metal arc welding for general construction in mild steel.
IS 822-1970 Code of practice for inspection of welds
IS 9595-1980 Recommendations for metal-arc welding of carbon and carbon manganese steels.
c) For welding for any particular type of joint, welders shall submit evidence acceptable to the Consultant of having satisfactorily completed appropriate tests as described in the following relevant Indian Standards.
IS: 7307-1974 Approval tests for welding procedure.
IS 7310-1974 Approval tests for welders working to approved welding procedure.
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
25
SIGNATURE & SEAL OF TENDERER
Unless otherwise stated all welds shall be electric metal arc welds.
d) All welding procedures shall be arranged, to suit the details of joints indicated on the drawings. Welding shall be carried out shall be such as to ensure that the weld metal is full and satisfactorily deposited throughout the length and thickness of all joints.
Members to be welded shall be securely held in their relative position during welding, either by jigs or tack welding.
Profile of fusion faces may be prepared by shearing, chipping, or gas cutting. In all cases the faces should be dressed by chipping, filling or grinding and made regular.
For thickness of metal 16 mm and above, electrodes used shall be Supercito (E-7018) or equivalent. For thicknesses of metal below 16 mm the root run shall be with Phillpe 31 (E 6010) electrodes, (or equivalent) and subsequent runs shall be with Overchord - SS (E- 6013) electrodes (or equivalent). The electrodes shall be dried in an electric oven as per the recommendations of manufacturers. Only DC current shall be used for welding and the Contractor shall make his own arrangements of all welding power and for equipment.
Vertical down welding shall not be permitted. All welds shall be back-gouged and welded from the backside unless specifically approved otherwise.
All welds shall be carried out in such a sequence and manner as to cause minimum distortion of the welded parts.
Multiple run welds shall be carried out with each run closely following the previous run, but so that sufficient time is allowed for slag removal.
Welds shall on completion present an even, smooth and regular finish free from defects. The weld metal shall be solid throughout with complete fusion between weld metal and parent metal and between successive runs throughout the joints. Caulking shall not be used to correct defects.
17.2 Surface Cleaning Prior to Welding
Surfaces to be welded shall be free from loose scale, slag, rust, grease, paint and other foreign materials. Surfaces need not be cleaned of Zinc Silicate primer if present prior to welding.
17.3 Cleaning
Upon completion of each welding pass, the weld shall be cleaned of spatter, slag and flux deposits. The weld must show a good clean contour and on a cut specimen good fusion with the parent metal. After welding is complete, adjacent surfaces shall be thoroughly cleaned of all spatter and deposits.
17.3 Size of Welds
All structural welds shall be continuous around all mating faces and edges of the members being connected. If not detailed on the drawings welds shall be sized to
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
26
SIGNATURE & SEAL OF TENDERER
develop the full strength of the smaller of the two members being joined and not less than 8mm.
17.4 Compatibility of Welds
All welds shall develop the strength and ductility specified for the steel being welded. Welds forming connections between steel of different grades shall develop at least the same unit strength as that specified for the higher strength steel.
17.5 Automatic Welding
Automatic and semi-automatic welding processes may be employed provided they are approved by the Engineer and conform to the requirements of these specifications. All equipment for automatic and semi-automatic welding shall be subject to approval by the Consultant. Pre-heating will be required where any section thickness exceeds 30mm. Requirements for, and method of, pre-heating shall be submitted to the Consultant for approval.
17.6Inspection
Upon completion of steel fabrication and before any surface treatment is applied, the Contractor shall allow inspection of the steelwork by the Consultant who may reject the steelwork if it fails to meet the requirements of this Specification.
17.7 Following welding tests shall be carried out if asked by Consultants at contractors' cost.
Ultra Sonic test for fillet weld
18 MISCELLANEOUS METALS
18.1 Fabrication
All miscellaneous metal work shall be formed true to detail, with clean, straight, sharply defined profiles, and smooth surfaces of uniform colour and texture and free from defects impairing strength or durability.
Connections and accessories shall be of sufficient strength to safely withstand stresses and strains to which they will be subjected. Accessories and connections to steel or cast iron shall be steel, unless otherwise specified. Threaded connections shall be made so that fitting conceals the threads.
Welded joints shall be rigid and continuously welded. The face of welds shall be dressed flush and ground smooth. Exposed joints shall be close fitting and joined where least conspicuous.
18.2 Finishes
All steel work shall be thoroughly cleaned, by effective means, of all loose mill scale, rust, grease and foreign matter and shall be treated in the workshop prior to
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
27
SIGNATURE & SEAL OF TENDERER
transportation. If painted it shall be applied to dry surfaces and shall be thoroughly and evenly spread and well worked into joints and open spaces. Abrasions in field erection shall be touched up (including primer) immediately after erection.
18.3 Bolts and Nuts
Screw and bolt anchors, that are not shown, shall be cinch anchors, rawl or of the slug-in type. Anchors shall be minimum "two unit" type. Toggle bolts shall be of the size indicated and shall be galvanised. Bolt and nut threads shall be galvanised and shall conform to the aforementioned codes.
18.4 Chemical Anchors
The Contractor shall supply and install all chemical anchors shown on the Drawings. Chemical anchors shall be Hilti - Masonry Rawl Plug anchors or approved equivalent. Substitution with Dynabolt or expansion bolts shall not be permitted. After completion of the drilling of the hole for the chemical anchor the hole shall be cleaned of dust using compressed air.
18.5 SURFACE TREATMENT
Following the completion of fabrication all steel shall be cleaned and protective coated in accordance with the procedures specified in the Surface Treatments Section of this specification.
Protective coatings damaged during the Contract shall be rectified as specified in the Surface Treatments Section of this Specification and/ or to the approval of the Engineer at the Contractor's expense.
All bolts, nuts and washers shall be hot dipped galvanised unless noted otherwise. These and any other items as detailed on the Drawings and the Specification to be hot dipped galvanised shall be in accordance with IS: 1239 (Part I and II) or an equivalent approved standard.
19 MISCELLANEOUS
19.1 Inspection and Testing
The Project Engineer shall have free access at all reasonable times to those parts of the Contractors works which are concerned with the fabrication of the steel work. He shall be afforded all reasonable facilities for satisfying himself that the fabrication is being undertaken in accordance with the provisions of the Specification. Unless specified otherwise, inspection shall be made at the place of manufacture prior to dispatch and shall be conducted so as not to interfere unnecessarily with the operation of the work.
The Contractor shall guarantee compliance with the provisions of the Specification, if required to do so by the Engineer. Should any structure or part of a structure be found not to comply with any of the provisions of the Specification, it shall be liable to rejection. No structure or part of the structure, once rejected shall be resubmitted for
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
28
SIGNATURE & SEAL OF TENDERER
test, except in cases where the Consultant considers the defect as rectifiable. Defects, which may appear during fabrication, shall be made good by the Contractor with the consent of, and according to the procedure laid down, by the Consultant.
The Contractor shall supply all gauges and templates necessary to satisfy the Consultant. The Consultant may, at his discretion, check the test results obtained at the Contractor’s works by independent tests at the Government Test House or elsewhere. Should the material tested be found to be unsatisfactory, the costs of such tests shall be borne by the Contractor, and if satisfactory, the costs shall be borne by the Employer.
20 ERECTION
20.1Plant and Equipment The suitability and capacity of all plant and equipment used for erection shall be to the satisfaction of the Consultant. Details of the proposed equipment shall be submitted for approval 6 weeks prior to erection commencing.
20.2 Storing and Handling All structural steel should be so stored and handled at the site that the members are not subject to excessive stresses and damage.
20.3 Setting out
The positioning and levelling of all steel work with accuracy shall be in accordance with the approved Drawings, Specifications and to the satisfaction of the Consultant.
20.4 Security During Erection
During erection, the steel work shall be securely bolted or otherwise fastened and, where necessary, temporarily bracing provided for all load to be carried by the structure during erection including those due to erection equipment and its operation. No permanent bolting or welding should be done until proper alignment has been obtained.
20.5 Field Connections
All field assembly and welding shall be executed in accordance with the requirements for shop fabrication, excepting such as manifestly apply to shop conditions only. Where the steel has been delivered painted, the paint shall be removed before field welding, for a distance of at least 50 mm on either side of the joints.
20.6 Painting after Erection
Prior to the painting of steel, which is delivered unpainted, commences, all surfaces to be painted shall be dry and thoroughly cleaned from all loose scale and rust. The specified protective treatment shall be completed after erection. All bolt heads and site welds shall be cleaned.
INDIAN INSTITUTE OF TECHNOLOGY, BOMBAY
Cold Room, Freezer room and cold room racks in the Canteen Kitchen of Hostel-15 and 16 for Indian Institute of Technology, Bombay, within I.I.T. campus Powai, Mumbai-400076
TENDER DOCUMENT –
TECHNICAL SPECIFICATION
29
SIGNATURE & SEAL OF TENDERER
Where the steel has been surface treated in the workshop, the coating shall be completed on site so as to be continuous over any welds and site rivets or bolts. Bolts, which have been galvanized or similarly treated, are exempted from this requirement. Surfaces, which will be inaccessible after site assembly, shall receive the full-specified protective treatment before assembly.
21 GROUTING
Unless otherwise stated on the Drawings a space of not less than 25mm shall be provided between undersides of column base plates and between all beam and roof truss bearings, and concrete pads, footings etc.