Upload
vandieu
View
226
Download
0
Embed Size (px)
Citation preview
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C1/20054498/PS [E-Tender No.8000008027
Minimum Guaranteed Specifications Confirmed (Yes/No)
1 Digital 5 kV Insulation Resistance Tester:7594236031
2
3
5
6
7
8
9
10
11
12
13
14 Real time resistance against time graph plotting facility to graphically illustrate the response of a material to an applied test voltage
15
16
17
18 Insulation resistance will be measured at equally sequenced test voltages
19
20
21
22
23
24
25
26 Make & Model No to be specified
28 Year Of Manufacture of equipment should be 2014 or later29
30 Party to support the service of the equipment for 7 years from date of supply.
party should have authorised service centre in India.
Field service Application
Challenge Clause : GAIL may send the supplied equipment to government laboratory to check conformance to Minimum guaranteed
specifications.In case of any deviation ,party has to replace the equipment and provide new one with above specs.
All parameters can be measured and displayed in one single measurement
Built in noise rejection filters and shielded test leads supplied in a standard set
Dual power source – receptacle or rechargeable batteries
Built in internal memory storing 1000 measurements with time and date
CAT IV 600V overvoltage category for industrial applications.Certificate to be provided.
4
Capacitance Measurement Diagnostic tools
Polarization index (PI) Dielectric discharge (DD) Tests
Dielectric Absorption Ratio (DAR) with automated resistance ranging (AR).
Discharging Resistance ±10%
Mains Power Supply 90 - 260VAC, 45 - 60 Hz, 60VA
300 kΩ
External Voltage Measurement 0 – 600V ±(3% rdg + 4V) @ 45 to 65Hz and DC
Capacitance Measurement 0.0– 99.9, 100 – 999 nF
1.00 – 50.00 µF
±(5% rdg + 4 nF)
Dielectric Discharge Test (DD) 0 – 99.9 ±(5% rdg + 2 dgts)
Leakage Current Display Range 0 – 5.50 mA ±(5% rdg + 2 dgts)
Dielectric Absorption Ratio (DAR) 0 – 99.9 ±(5% rdg + 2 dgts)
Polarization Index (PI) 0 – 99.9 ±(5% rdg + 2 dgts)
Display Range Test Voltage ±(3% rdg + 3V)
±(3% of reading)
Current Display Range 0.00 – 9.99, 10.0 – 99.9, 100 – 999 nA
1.00 – 9.99, 10.0 – 99.9, 100 – 999 µA
1.00 – 5.5 mA
±(5% rdg + 0.05 nA)
0 – 5500V
from 250V to 5000V with 25V increments
DC Test Voltage and Step Voltage
Accuracy
Insulation Resistance 0 - 999 k ohms
1.00 - 9.99, 10.0 - 99.9, 100 - 999 M ohms
1.00 – 9.99, 10.0 – 99.9, 100 – 999 GΩ
1.00 – 10.00 TΩ
±(5% rdg + 3 dgts) below 1TΩ
±(15% rdg + 3 dgts) @ 1TΩ and above
250 V to 5 kV, steps by 25 V
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C2/20054498/PS [E-Tender No.8000008027
Confirmed
Yes/No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
AC/DC voltage measurementAccuracy Confirmed
Yes/No
Earth bond resistance measurement
Insulation specificationsTest voltage accuracy: + 20 %, - 0 %
Short-circuit test current: 1 mA nominal
Auto discharge: Discharge time < 0.5 second for C = 1 µF or less
Maximum capacitive load: Operable with up to 1 µF load
Accuracy1
+ (% of Rdg + Digits)
20.00 0.01
± (1.5 % + 3)200.0 0.
2000 1
20.00 0.01
50 Hz to 400 Hz
± (% of Rdg + Digits)
600.0 V 0.1 V ± (2 % + 3)
Minimum Guaranteed Specifications
Digital Insulation Resistance Tester with Max Test Voltage 1 kV DC:7594239271
Insulation test range:
Insulation test voltages:
Automatic calculation of Polar- ization Index and Dielectric Absorption Ratio
Make repetitive tests with the Compare (Pass/Fail) function
Repetitive or hard-to-reach testing with the remote test probe
Range Resolution
Live circuit detection if voltage
Auto-discharge of capacitive voltage
AC/DC voltage: 0.1 V to 600 V
auto power off
backlit display
CAT IV 600 V overvoltage category rating
One-year warranty
16
17
Range Resolution
18
200 mA Continuity
Resistance to
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C3/20054498/PS [E-Tender No.8000008027
Accuracy
Confirmed Yes/No
General Specifications Confirmed
Yes/NoMaximum voltage applied to any terminal:
600 V ac rms or dc
21 Storage temperature: -40 °C to 60 °C (-40 °F to 140 °F)
Operating temperature: -20 °C to 55 °C (-4 °F to 131 °F)
Temperature coefficient: 0.05 x (specified accuracy) per °C for temperatures < 18 °C or > 28 °C
(< 64 °F or > 82 °F)
Relative humidity noncondensing:
0 % to 95 % @ 10 °C to 30 °C (50 °F to 86 °F)
0 % to 75 % @ 30 °C to 40 °C (86 °F to 104 °F)
0 % to 40 % @ 40 °C to 55 °C (104 °F to 131 °F)
24 Vibration: Random, 2 g, 5-500 Hz per MIL-PRF-28800F, Class 2 instrument
25
(EN 61326-1:1997)
Safety: Complies with ANSI/ISA 82.02.01 (61010-1)
2004, CAN/CSA-C22.2 NO. 61010-1-04, and IEC/EN
61010-1 2nd Edition for measurement category IV 600 V (CAT IV) Certificate to be provided.
Battery life
Insulation test use: Tester can perform at least 1000 insulation tests with fresh alkaline batteries at room temperature.
Resistance measurements: Tester can perform at least 2500 earth bond resistance measurements .
28 IP rating: IP40
Altitude
Operating: 2000 m CAT IV 600 V, 3000 m CAT III 600 V
Non-operating (storage): 12,000 m
± (10 % + 3)
1000 V
(0 % to + 20 %)
0. to 0.
1
± (1.5 % + 5)200 to 1
2.0 to 0.
Shock: 1 meter drop per IEC 61010-1 2nd Edition (1 meter drop test, six sides, oak floor)
1
± (1.5 % + 5)20.0 to 0.
200 to 1
1
± (1.5 % + 5)20.0 to 0.
100 V
(0 % to + 20 %)
0.01 to 0.01 1± (3 % + 5)
20.0 to 0.
Accuracy
± (% of Rdg + Digits)
50 V
(0 % to + 20 %)
0.01 to 0.01 1
± (3 % + 5)
20.0 to 0.
Output Voltage Display Range Resolution Test Current
29
20
22
19
250 V
(0 % to + 20 %)
0.01 to 0.01
23
26
27
500 V
(0 % to + 20 %)
0.01 to 0.01
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C4/20054498/PS [E-Tender No.8000008027
30 Over-range capability: 110 % of range
31 Included accessories: Test Leads, Test Probes, clips , holster and remote probe
32 Service party should have authorised service centre in India.
33 Application Field service
34 Make & Model No to be specified
35Year Of Manufacture of equipment should be 2014 or later
36
37 Party to support the service of the equipment for 7 years from date of supply.
Challenge Clause : GAIL may send the supplied equipment to government laboratory to check conformance
to Minimum guaranteed specifications.In case of any deviation ,party has to replace the equipment
and provide new one with above specs.
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C5/20054498/PS [E-Tender No.8000008027
Minimum Guaranteed Specifications Confirmed (Yes/No)
1Measurement Range Resolution Accuracy ± ([% of reading] + [counts])
2DC millivolts 600.0 mV 0.1 mV 2.0 % + 3
3 6.000 V 0.001 V
60.00 V 0.01 V
600.0 V 0.1 V
4Auto volts 600.0 V 0.1 V 2.0 % + 3 (dc, 45 Hz to 500 Hz)
4.0 % + 3 (500 Hz to 1 kHz)
5AC millivolts
true-rms
600.0 mV 0.1 mV 1.0 % + 3 (dc, 45 Hz to 500 Hz)
2.0 % + 3 (500 Hz to 1 kHz)
6 6.000 V 0.001 V
60.00 V 0.01 V
600.0 V 0.1 V
7Continuity 600 Ω 1 Ω Beeper on < 20 Ω off > 250 Ω; detects
opens or shorts of 500 µs or longer.
8 600.0 Ω 0.1Ω 0.9 % + 2
6.000 kΩ 0.001 kΩ
60.00 kΩ 0.01 kΩ
600.0 kΩ 0.1 kΩ
6.000 MΩ 0.001 MΩ
40.00 MΩ 0.01 MΩ 1.5 % + 2
9 Diode test 2.000 V 0.001 V 0.9 % + 2
10 1000 nF 1 nF
10.00 µF 0.01 µF
100.0 µF 0.1 µF
9999 µF 1 µF
100 µF to 1000 µF 1.9 % + 2
> 1000 µF 5 % + 20
11 Lo-Z capacitance 1 nF to 500 µF 10 % + 2 typical
126.000 A 0.001 A
10.00 A 0.01 A
13 6.000 A 0.001 A
10.00 A 0.01 A
14 99.99 Hz 0.01 Hz
999.9 Hz 0.1 Hz
9.999 kHz 0.001 kHz
50.00 kHz 0.01 kHz
15
Hz (V or A input) 0.1 % + 2
1.5 % + 3
20 A continuous overload for 30 seconds max.
DC amps 1.0 % + 3
20 A continuous overload for 30 seconds max.
True RMS Digital Handheld Multimeter:9126440121
All inputs shall be protected to the 2nd edition of ANSI/ISA S82.01 and EN61010-1 CAT III 600V. They can
withstand impulses in excess of 6000 Volts.Certificate to be provided.
DC volts
AC volts true-rms 1.0 % + 3 (45 Hz to 500 Hz)
2.0 % + 3 (500 Hz to 1 kHz)
Ohms
0.9 % + 1
Capacitance 1.9 % + 2
AC amps true-rms
(45 Hz to 500 Hz)
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C6/20054498/PS [E-Tender No.8000008027
16
17
18Surge protection
19Service
20Application Field service
21
22
23Year Of Manufacture of equipment should be 2014 or later
24
25 Party to support the service of the equipment for 7 years from date of supply.
Challenge Clause : GAIL may send the supplied equipment to government laboratory to check
conformance to Minimum guaranteed specifications.In case of any deviation ,party has to replace the
equipment and provide new one with above specs.
Make & Model No to be specified
Standard Accesorries to be provided.
For operator safety, DMM shall have Input Alert to provide audible warning against
wrong use of input jack.
DMM shall have analog bar-graph with min/max/avg to record signal fluctuations and datahold feature. Display
should be of 6000 counts with update of 4 times/second.
6 kV peak per IEC 61010-1,600 V CATIII,Pollution degree 2
party should have authorised service centre in India.
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C7/20054498/PS [E-Tender No.8000008027
Confirmed Yes/No
1
2 AC CurrentRange
3Accuracy
4 Crest Factor
5 AC Response
6 DC CurrentRange
7Accuracy
8 AC Voltage Range
Accuracy
9AC Response
DC Voltage Range
Accuracy
Resistance Range
Best Accuracy
12 Capacitance Range
13Best Accuracy
14 Continuity
15 Frequency
Range
16Accuracy
17
Temperature
Range
18
Accuracy
20 Operating Temperature
21Humidity (W/o Condensation)
22
Overvoltage category
23
24
25
26
19 Service
20 Application
21 Make & Model No to be specified
22
23 Year Of Manufacture of equipment should be 2014 or later
24
25 Party to support the service of the equipment for 7 years from date of supply.
26
Field service
party should have authorised service centre in India.
Challenge Clause : GAIL may send the supplied equipment to government laboratory to check
conformance to Minimum guaranteed specifications.In case of any deviation ,party has to
replace the equipment and provide new one with above specs.
Standard Accesorries to be provided.
19 Case,Test Leads,Current Clamp,Temperature probe to be supplied
True RMS Digital Handheld Multimeter:7594507591
45 Hz to 1 kHz
Voltage Input: 2 Hz to 100 kHz Current Input:
2 Hz to 30 kHz
+/- (0.1% of reading plus 1 count)
11
10
+/ - (1.5% of reading plus 3 counts)
<= 3
Display Hold and Auto Hold.
Min-max-average recording
DMM shall be independently tested for safe use in CAT IV 600V/CAT III 1000V
environments. All inputs are protected to IEN61010-1 CAT IV 600V/CAT III
1000V. Certificate to be provided.
Minimum Guaranteed Specifications
Beeper on for <25 Ω, off >250Ω; detects opens or shorts of 250 µs or longer
0.01 mA to 10.00A (20A overload for
30 seconds)
45 Hz to 500 Hz
1% of rdg + 3 counts
500 Hz to 1 kHz
2% of rdg + 3 counts
0.1 mV to 1000V
+ / - (1.0% of reading plus 3 counts)
+/- (1.2% of reading plus 2 counts)
1 nF to 9999 µF
-40 degC to +400 degC,
-40 F to +752 F
1% + 1.0 degC,
1% + 1.8 degF
DMM shall be 3.5 digit, 6000-count resolution
45 Hz to 1 kHz
+/- (0.9% of reading plus 1 count)
0.1 Ω to 50.00
UL Approved
0.01 mA to 10.00A (20A overload for
30 seconds)
+/- (0.09% of reading plus 2 counts)
0.1 mV to 1000V
-10°C to +50°C
0% - 90% (0°C - 35°C), 0% - 70% (35°C -50°C)
Manual and automatic ranging
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING
INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C8/20054498/PS [E-Tender No.8000008027
Confirmed Yes/No
1 Range 40.00 A/400.0 A
Accuracy 2 % ± 5 digits
(45 Hz to 65 Hz)
2.5 % ± 5 digits
(65 Hz to 400 Hz)
2 Range 40.00 A/400.0 A
Accuracy 2 % ± 5 digits
3 Range 600.0 V
Accuracy 1.5 % ± 5 digits
4 Range 600.0 V
Accuracy 1.0 % ± 5 digits
5 Range 400.0 Ω/4000 Ω/40.00 kΩ
Accuracy 1 % ± 5 digits
6 Continuity ≤ 30 Ω
7 100.0 µF to 1000 µF
8 5.0 Hz to 500.0 Hz
9 True-rms
10 Yes
11 Yes
12-10.0 °C to 400.0 °C (14.0 °F to 752.0 °F)
13 Yes
15CAT III 600 V ,CAT IV 300
V.Certificate to be provided.
16 Two-year
17
18
19
20
21
22
23
24 Year Of manufacture: 2014 or later
Capacitance
Frequency
AC response
Backlight
Contact temperature
Shall have Min, max, and inrush recording to capture variations
automatically
Shall have min 30mm jaw size for measuring current in conductors
/ cables
Shall have large, easy to read backlight display automatically with
auto range selection to avoid need to change the switch positions
while taking a measurement.
Case,Test Leads,calibration certificate to be supplied
True RMS Digital Handheld Clamp Meter:7594108001
Minimum Guaranteed Specifications
Shall have low 40A and 400A current ranges to allow better
measurement at low currents with auto range selection feature.
Shall have 600V AC/DC voltage measurement
Shall have continuity check, diode check, data hold and backlit LCD
display
Data hold
AC current
DC current
AC voltage
DC voltage
Resistance
Min/Max
Category rating
Warranty
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C9/20054498/PS [E-Tender No.8000008027
Minimum guaranteed Specifications Confirmed Y/N
1
2
3
RESISTANCE: RANGE RESOLUTION TOLERANCE
0 - 200 milli Ω 0.10 milli Ω ± 2%
0 – 2 Ω 0.001 Ω ± 2%
0 – 20 Ω 0.01 Ω ± 2%
0 – 200 Ω 0.10 Ω ± 2%
INDUCTANCE: RANGE RESOLUTION TOLERANCE
0 – 2 m H 0.001 mH ± 3%
0 – 20mH 0.01 mH ± 3%
0 –200 mH 0.1 mH ± 3%
0 –2000 mH 1 mH ± 3%
6
7
8
9
Industrial Handheld Digital Motor Checker : 7594491111
Operating Temp. Range: 0- 55ºC
Power : 1.5V x 6 AA size (Battery Pack)
4
5
Digital portable diagnostic Meter for on - site checks of electric motor and other three -phase machines.
The meter has separate operating modes to measure different types of faults .
INSULATION RESISTANCE (IR): 0 – 200 MΩ at 500 V DC ± ( 2% + 1digit), 0.1 MΩ resolution
Display: 3½ LCD
Low battery Indication
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C10/20054498/PS [E-Tender No.8000008027
Minimum Guaranteed Specifications Confirmed Yes/No
1 Digital Handheld Lux level Meter:9129510011
2 Illumination Accuracy at 23°C ± 5°C (73.4°F ± 5°F), < 75% R.H.
3 Sensor Silicon photodiode and filter
4 Measurement rate 2.5 times per second
5 Range 20, 200, 2000, 20000, 200000 Lux
20, 200, 2000, 20000 Foot candles
6 Accuracy ± 3% (Calibrated to standard incandescent lamp at 2854°K) 6% other visible light sources
7
60° ± 6%
8
9 Display 3¾ digit liquid crystal display (LCD) with a maximum reading of 1999
10 Sampling Rate 2.5 times per second for digital display
11 Polarity Automatic, positive implied, negative polarity indication
12 Overrange (OL) or (-OL) is displayed
13 Zero Automatic
14
15 Temperature / Humidity Operating -10°C to 50°C (14°F to 122°F), 0 to 80%RH
Storage -10°C to 50°C (14°F to 122°F), 0 to 70%RH
16 Agency Approvals & Certifications
17Party should have authorised service centre in India.
18
19 Make & Model No to be specified
20Year Of Manufacture of equipment should be 2014 or later
21
22Party to support the service of the equipment for 7 years from date of supply.
Low battery indication The symbol is displayed when the battery voltage drops below the operating level
30° ± 2%
Angle deviation from cosine Characteristics 30°
Resolution 0.01 fc/lux
80° ± 25%,Cosine Angular corrected per JIS C 1609:1993 and CNS 5119 general A class.
Challenge Clause : GAIL may send the supplied equipment to government laboratory to check conformance to Minimum
guaranteed specifications.In case of any deviation ,party has to replace the equipment and provide new one with above
specs.
Field service Application
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C11/20054498/PS [E-Tender No.8000008027
Minimum Guaranteed Specifications Confirmed Yes/No
1
2
3
4
5
6 Measuring Ranges
7
8
9
10 Resolution
11
12
13
14 Yd/Min Unit 0.0001/0.001/0.01/0.1
15 Accuracy +/-(0.1% of rdg.+2 digit)
16
17 Operating RH% Humidity < 80%
18
19 Storage RH% Humidity < 90%
20 EMC EN 61326-1
21 Time base 4.0Mhz Quartz Crystal
22 Sampling time 1 second (>60RPM), >1 second (10~60RPM)
23 Measure distance 5~30cm / 2~13 IN (non-contact)
24 Included Accessories Meter, 9V battery, Cone & funnel contact tips, Reflective tape, Users manual
25
26
27 Make & Model No to be specified
28 Year Of Manufacture of equipment should be 2014 or later
29
30 Party to support the service of the equipment for 7 years from date of supply.
Rotation (Non-Contact) 10.0 - 99999RPM
Rotation (Contact) 10.0 - 19999RPM
RPM Unit 0.001 / 0.01 /0.1 /1
M/Min Unit 0.0001 / 0.001 /0.01 /0.1
Ft/Min Unit 0.0001 / 0.001 /0.01 /0.1
Contact/Non contact Digital Hand held Tachometer:7594701371Measures rotational and surface speed
User selectable units for contact measurement: RPM, m/min, ft/min, yd/min
Non-contact measurement in RPM Digital Display
Auto power off function
Challenge Clause : GAIL may send the supplied equipment to government laboratory to check conformance to Minimum guaranteed specifications.In case
of any deviation ,party has to replace the equipment and provide new one with above specs.
Field service Application
party should have authorised service centre in India.
Surface Speed (Contact) 1.0000~9999.9 m/min ,3.0000 – 30,000 ft/min
Operating Temp. 0 to 50 degC (32˚ to 122˚F)
Storage Temp. -10 to 50 degC (14˚ to 122˚F)
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C12/20054498/PS [E-Tender No.8000008027
9305050311
1 Confirmed Yes/No
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49 The Infrared Thermal Imaging Camera should be portable, hand held, easy to use and rugged for field application. Maximum weight of the camera
including battery should less than 1.5 Kg. The camera should be provided with required software/ hardware and associated accessories to enable scanning
of various electrical and mechanical equipments for detection of hot spot and for predictive and preventive maintenance applications. The camera should
be suitable for detecting problems in a variety of power plant systems and equipments including Boiler, Turbine Generator set electrical switchgear,
gearboxes, Switchyards, electrical panels, motors, bearings, steam lines and process system that rely on heat retention or transfer.
Image browsing
Seamless Export of image and data to standard windows program like word or excel
Date /Time stamping and all technical parameters and atmospheric conditions corresponding to image shall be simultaneously stores.
Provision should be there to view thermal and visual image simultaneously on Laptop.
Carrying Hard Case
Rechargeable Battery 2 nos. with powerful Battery charger for at least 4 hrs of nonstop scanning.
Communication cables
Power supply cord
Two sets of operation maintenance instruction manual in book form.
AC adapter
Two sets of complete documentation on software for camera.
Report generations of multiple images, report must be generated in MS word and Pdf format.
Must be compatible for windows .
Report designing and preparation in pdf/, doc/ xls. Excel report must be able to upload in SAP System.
Soft key operation must be there on camera.
Digital Temperature readout: The digital temperature readout must be there in the camera.
Visual Image: Through in built visual digital camera. Picture in Picture or full real and thermal image
The calibration certificate for infrared thermal imaging camera must be submitted by the vendor.
The party should carry out complete live demonstration and installation of the system along with its software capabilities, report generation
At least two employees of GAIL shall be trained by the party for infrared thermal imaging camera.
The equipment should bear a warranty of at least two year after receipt, inspection and demonstration at site.
Supplier shall have adequate OEM/OES authorized Services facility and calibration lab in India and documentary evidence of the same.
The manufacturer should provide a certificate for availability of spares of thermal imager for 10 year from date of purchase in India.
Windows based analysis software. The camera must be supplied with image transfer and image analyzing software.
Standard Accesorries to be provided.
Image viewing: (3.5’’ min). This LCD display shall be powered from the camera battery.
On screen image analysis: Max., Min., spot temperature in Celsius, Isotherm, selectable color pallet, battery indication.
Focus: Auto or Manual
Connectivity: Camera should have video output OR USB-2 port or Blue tooth or Wi-Fi(OPTIONAL)
Cooling: Integrated/ uncooled detector (No external Nitrogen based cooling).
Startup Time < 1 Min
AC Adapter; 240±10% VAC, 50 Hz
Humidity: 20% to 80% (non condensing)
Shock withstand: 25G as per IEC 68-2-29
Vibration withstand: 2G as per IEC 68-2-6
Storage temp range: -10° -- +50° C
Operating temp range: -10° -- +50° C
Image storage: At least 800 to 1000 images either in internal memory or memory card capacity minimum 2Gb,
Thermal imager resolution: resolution of thermal imager should be 160x 120 pixels
or better. Lens Field of View 32°x23° or more with spatial resolution: 3.3 m Rad or less. Spectral range: 7.5-14 µm or better,
Frame rate should be greater than 30HZ.
Minimum Guaranteed SPECIFICATION OF PORTABLE INFRARED THERMOVISION CAMERA:
Temperature range : -20 deg C to 350 deg C.
Minimum Focal Range : : 15 cm to 40cm
Thermal Resolution: 0.1° C at 30° C or better.
Thermal Sensitivity : ≤0.06 °C at 30 °C OR LOWER
NETD : < 50 mK
Correction factor: Emissivity, Background temp.
Accuracy of measurement : ±2% of the reading
Image file format: .bmt; export option in .bmp, .jpg, .png, .csv, .xls
Measurement Spots: Three or above
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C13/20054498/PS [E-Tender No.8000008027
Confirmed Yes/No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Standard Accessories
17 Timing Test Cables, High Flexibility,Wear Resistant, 15m - 1 Set
18 Breaker Control Cable, 7m - 1 No.
19 Hard Carrying Case for Instrument - and Test Lead Set - 1 No.
20 PC Downloading & Analysis Software on CD - 1 No.
21 Instruction Manual - 1 No.
22 Factory Test & Calibration Report - 1 No.
23 - 1 No.
24 - 1 No.
25 - 1 No.
26 - 1 Set
Minimum Guaranteed Specs
Circuit Breaker Time Interval Digital Meter:7597251291
3 (Main contacts of 3 poles connect- end to end, simultaneously)
Master Earthing Cable, 7m
USB Cable
Keypad
Memory 1 MB, 100 records, Internal
Inbuilt Battery Li-Ion
Trigger Options Close, Open, Close-Open
Display backlit LCD
Resolution
Battery Charger
Spare Fuses
Environment 0 to 50°C, Upto 95% RH (Non condensing)
Battery Charger Input Supply - 100 to 300 VAC, 50/60 Hz +/- 10%
Communication Port USB
Software For PC Downloading & Analysis, Windows based
0.1 mSec, 0.2 mSec, 0.5 mSec, 1 mSec & 10 mSec respectively for above Sampling Speeds
Accuracy Value ± 0.05%± 1 Digit
Breaker Control Two solid state contacts rated at 35A, 300V AC/DC for breaker operation
Timing Range 1Sec, 2Sec, 5Sec, 10S & 100Sec respectively for above Sampling Speeds
Contact Timing Channels
Sampling Speed 10kHz, 5kHz, 2kHz,1kHz & 100Hz, Selectable
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C14/20054498/PS [E-Tender No.8000008027
27 Test Lead Set of 7m length for MV/HV CBs - 1 Set
28
29
30
31
32
33 Party to support the service of the equipment for 7 years from date of supply.
Party should have authorised service centre in India.
Field service Application
Make & Model No to be specified
Year Of Manufacture of equipment should be 2014 or later
Challenge Clause : GAIL may send the supplied equipment to government laboratory to check conformance to Minimum guaranteed specifications.In case
of any deviation ,party has to replace the equipment and provide new one with above specs.
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C15/20054498/PS [E-Tender No.8000008027
Confirmed : Yes/No
1
2
3
4
5
6
7
8
9
10
11
12
13 Service party should have authorised service centre in India.
14 Application Field service ,Portable
15 Make & Model No to be specified
16
17 Year Of Manufacture of equipment should be 2014 or later
18
19 Party to support the service of the equipment for 7 years from date of supply.
Stability : +/ - 0.3 deg C
Mimimum Guaranteed Specifications
Digital Temperature calibrator: 8164411041
Input : 230 V (+/- 5%), 1 phase, 50 Hz.
Temp Range : 0-120 deg C.
Resolution : 0.1 deg C
Standard Accesorries to be provided.
Challenge Clause : GAIL may send the supplied equipment to government laboratory to check conformance
to Minimum guaranteed specifications.In case of any deviation ,party has to replace the equipment
and provide new one with above specs.
Medium of Cooling : Methanol.
Sensor : Precision PRT.(PT-100)
Controller: Digital self tuned PID
Accuracy : 0.5 deg C
Opearating temp: 5-45 Deg C
Time to reach max temp : 30 min.
Medium of Heating: Silicon Oil.
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR
PC-II ,GAIL (INDIA) LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C16/20054498/PS [E-Tender No.8000008027
Sl. No. Confirmed : Yes/No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17 Application: Industrial field testing of various equipment.
Voltage Variation: Simultaneously in all 3 phases Manually by rotating Dial.
REGULATION : less than 3 %
TEMPERATURE RISE - Less than 50 degrees for continuous operation.
Rugged construction
INSULATION - Class F.
WINDINGS - High conductivity copper insulated with synthetic
enamel ,
HIGH INITIAL SURGE CURRENTS- withstand initial surges ten
times the rated current.
Ratings quoted are for use in ambient temperature from -20'C to
+50'C. conform to Indian Standard Specifications. IS:5142 latest edition.
Variable transformer must be protected against overload and short
circuits with circuit breakers .Vendor to provide routine test certificates along with the equipment.
Cooling : Air Natural
Mimimum Guaranteed Specifications: 8435710051
Continuously Variable Voltage Auto Transformer
Input : 415 V (+/- 5%), 3 phase, 50 Hz.
Output : 0-475 V,3 phase, 50 hz.
Rated Current : 20 A
TECHNICAL SPECIFICATIONS FOR TENDER FOR PROCUREMENT OF ELECTRICAL TEST MEASURING INSTRUMENTS FOR PC-II ,GAIL (INDIA)
LIMITED, PATA (UP) INDIA
BID DOCUMENT NO: GAIL/PA15/C17/20054498/PS [E-Tender No.8000008027]
Confirmed Y/N
1
2
3
4
5
6
7
Confirm yes/no
1
2
3
4
5
6
7
8 Application: Domestic/Industrial , on site
Output : Mains Isolated AC injection current continuously adjustable from 0.01 A to 200 A for 3
minutes.
Minimum Guaranteed Specifications
ELCB/RCD/RCCB Test Kit
Mains Isolated, distortion less sine wave AC injection current
Compatible for NO/NC auxiliary trip contact selection
4 digit auto ranging Time Interval meter
Input: 230 V, 50 hz
Output : Mode 1. 10-60 mA, and Mode 2. 100-500 mA.
mA current display with DPM Modules
Application: Industrial , on site
Mains Isolated, distortion less sine wave AC injection current
Compatible for NO/NC auxiliary trip contact selection
4 digit auto ranging Time Interval meter
Input: 230 V, 50 hz
MCB/Bimetal OverLoad Relay test Kit : 7594631061
Minimum Guaranteed Specifications
MCB/Bimetal Over load Relay Test Kit