Industrial Mixers, Agitators, Aerators and Induction Systems

TURBULATORTECHNOLOGIESA Fluid Dynamic Company

www.turbulatortech.com

High Shear Industrial Mixing and Agitation

Mixing or agitation is an integral part of the production process. There was a need for a single design that would address both radial and axial flow all-in-one. The Turbulator was born to accommodate this vital need in industry and emerged from one simple, yet complete design.

Turbulator Technologies provides complete worldwide solutions to mixing and agitation problems across industries, raging from acid mine drainage and efflu-ent control, to back fill and diffi-cult sump applications, to food.

The Turbulator Mixer is an agitator-mixer unit for mixing of liquids and slurries. A strong vortex is created at both the upper and lower ends of the rotor. The bottom stream is pulled through the rotor and deflected upwards, forming a wave at the upper end of the mixing vessel, forcing powders and solids into the top vortex. The top stream is deflected downwards and it sweeps the bottom end of the mixing vessel, preventing any solids from settling on the vessel floor. High shear takes place due to the top and bottom streams cutting through one another as they exit the rotor.

Turbulator Technologies offers clients a turnkey solution that allows mixing, wetting, blending and aeration of solutions unattainable with existing industry technology. Applications include industrial mixing, mining, pharmaceutical applications, water and wastewater aeration, and more.

The unique mixing principle of the Turbulator rotor/impeller is based a simple, yet efficient, design. When observing the agitation process in a glass vessel, the distinctive “figure 8” within the liquid is visible. This pattern results in a strong vortex on both the upper and lower side of the rotor, pulling down floating powders from the surface as well as lifting and stirring up solids that would otherwise settle out. One can also observe the sweeping action along the tank walls which assists in the cleaning of the tank’s sidewalls as well as agitating the corners of rectangular tanks. These actions ensure a rapid, homogeneous mix throughout the vessel.

The design of the Turbulator is superior to the conventional paddle or marine blade impellers currently available on the market. The task of the turbulator rotor is to generate

a three-dimensional flow throughout a vessel and to maximize the contact area between the components within a multiphase system.

Increased production through quick dispersion.

Complete dispersion of solids from top to bottom.

User-friendly system.

Homogeneous mixing.

Particle size reduction.

No gearbox drives.

No bottom bearing.

No oil leakage into mixing vessel.

Low maintenance, reduce labor cost.

Quick rotor/impeller change

Limited splashing.

System Advantages: Maintenance Advantages:

Clean sweeping of vessel floor.

Electric Motor

Bearing Housing

Assembly

Turnkey service

Turbulator’s turnkey process includes auditing, design facilitation, installation, implementation, commissioning and supply of various services and products. Turbulator’s exceptional product and services are cost effective, sustainable and offer a return on your investment.

What to expect:

1. Consultation with Turbulator professionals

2. Research and Development (on and off site)

3. Design, construction and implementation

4. Training and education on site-specific solutions

5. Follow-up, monitoring, and evaluation of progress —with re-training where applicable

6. Continuous maintenance or preventative maintenance contracts

Lourens J. B. Smit - CEO

Email: lourens@turbulatortech.com

Mobile: 704-506-6275

Office: 704-644-8337

TURBULATORTECHNOLOGIESa fluid dynamic company

The ULTIMATE MIXING SolutionAeration and Gas Induction

Activated Carbon Mixing (PAC)

Liquid Lime Applications

Waste Water Treatment and many more

Turbulator components are manufactured in the U.S.A. from the best quality materials and conforms to industry standards.

It has a very basic design with direct drive for High Speed Mixing applications.

The HTD belt drive units require NO gearbox to reduce speed in low velocity agitation applications.

The design is perfect for a wide range applications including Aeration, Gas Induction, Activated Carbon Mixing, Liquid Lime Applications, Waste Water Treatment, and many more.

TURBULATOR TECHNOLOGIES’ success in all industries is built on unsurpassed 24/7 back-up and after-sales service, and conformance to ISO 9002 Standards.

We continually strive to improve our products every day and we work closely with our clients to assure quality of installation as well as proper maintenance. Turbulator can significantly speed up your mixing process, saving you time and money. Please contact us today to schedule a consultation