Tekelec EAGLE - Oracle · 2014-10-17 · EAGLE 5 ISS Release 43.0 Feature Content Introduction Feature notices are distributed to customers with each new release of software. This

Tekelec EAGLE® 5

Release 43.0

Feature Notice910-6006-001 Revision E

August 2012

Copyright 2012 Tekelec. All Rights Reserved. Printed in USA.Legal Information can be accessed from the Main Menu of the optical disc or on the

Tekelec Customer Support web site in the Legal Information folder of the Product Support tab.

Table of Contents

EAGLE 5 ISS Release 43.0.......................................................................................6Feature Content.........................................................................................................................63 Links per E5-ATM Card .......................................................................................................8

Feature Control Requirements....................................................................................8Hardware Requirements..............................................................................................8Commands.....................................................................................................................8Limitations...................................................................................................................10

10,000 Routesets ......................................................................................................................10Feature Control Requirements..................................................................................10Hardware Requirements............................................................................................10Commands...................................................................................................................10Limitations...................................................................................................................12

Additional DRA values for INP formatting .......................................................................12Hardware Requirements............................................................................................12Feature Control Requirements .................................................................................12Commands...................................................................................................................12Limitations...................................................................................................................13

Fall-back to GTT after LNP MR Service ..............................................................................13Feature Control Requirements..................................................................................13Hardware Requirements............................................................................................13Commands...................................................................................................................13Limitations...................................................................................................................13

G-Flex MLR Support for Additional OpCodes ..................................................................13Feature Control Requirements..................................................................................14Hardware Requirements............................................................................................14Commands...................................................................................................................14Limitations...................................................................................................................15

Hybrid INP/IDP Relay Service ............................................................................................15Feature Control Requirements..................................................................................16Hardware Requirements............................................................................................16Commands...................................................................................................................16Measurements..............................................................................................................22Limitations...................................................................................................................22

Multiple IDP Relay Instances ...............................................................................................23Feature Control Requirements..................................................................................23Hardware Requirements............................................................................................23Commands...................................................................................................................23

ii910-6006-001 Revision E, August 2012

Measurements..............................................................................................................23Limitations...................................................................................................................23

Point Code and CIC Translation ..........................................................................................24Feature Control Requirements..................................................................................24Hardware Requirements............................................................................................25Commands...................................................................................................................25Measurements..............................................................................................................30Limitations...................................................................................................................30

Pre-LNP Query Service GTT processing ............................................................................30Feature Control Requirements..................................................................................31Hardware Requirements............................................................................................31Commands...................................................................................................................31Limitations...................................................................................................................31

Support CRP check for SRI_SM using TCAP digits ..........................................................31Feature Control Requirements..................................................................................31Hardware Requirements............................................................................................31Commands...................................................................................................................31Limitations...................................................................................................................32

XUDT Conversion Enhancements .......................................................................................32Feature Control Requirements..................................................................................32Hardware Requirements............................................................................................33Commands...................................................................................................................33Measurements..............................................................................................................34Limitations...................................................................................................................34

Other Changes.........................................................................................................................34Change the number of digits in the MAP Routing Info of the returned

SRI_ACK message to 15 ......................................................................................35E5-TDM does not support Hardware Flow Control..............................................35Extended Processing Time Notification...................................................................35PC_TYPE in Daily Maintenance and Hourly Maintenance Per SSP

reports.....................................................................................................................37Support for the BLIXP GPL.......................................................................................38Update to the msucount Command.........................................................................41Update to the netstat Command...............................................................................43Update to rept-imt-lvl2 Command...........................................................................44Update to the rept-stat-imt Command....................................................................46Update to the rept-stat-rtkey Command.................................................................47

Operational Changes..............................................................................................................47UIMs..............................................................................................................................47Hardware Verification Code.....................................................................................49Error Messages............................................................................................................49

iii910-6006-001 Revision E, August 2012

Customer Care Center............................................................................................................54Related Publications...............................................................................................................57Customer Training..................................................................................................................57Locate Product Documentation on the Customer Support Site.......................................57EAGLE 5 ISS Card Overview Table.....................................................................................57Hardware Baseline..................................................................................................................63

Glossary....................................................................................................................69

iv910-6006-001 Revision E, August 2012

List of TablesTable 1: New MAP Operations Supported by the G-Flex MLR Feature ....................................14Table 2: UIM: Hybrid INP/IDPR Relay Service.............................................................................47Table 3: UIM: G-Flex MLR Support for Additional Opcodes.......................................................48Table 4: UIM: Multiple IDPR Instances...........................................................................................48Table 5: UIMs: XUDT Conversion Enhancements.........................................................................48Table 6: UIM: Non-Feature................................................................................................................49Table 7: Hardware Verification Code: 3 ATM Links per E5-ATM Card....................................49Table 8: Error Messages: 3 Links per E5-ATM Card......................................................................49Table 9: Error Message: 10,000 Routesets........................................................................................50Table 10: Error Messages: Fall-back to GTT after LNP MR service.............................................50Table 11: Error Messages: G-Flex MLR Support.............................................................................51Table 12: Error Message: Hybrid INP/IDP Relay Service............................................................51Table 13: Error Message: Multiple IDP Relay Instances................................................................51Table 14: Error Messages: PCT..........................................................................................................52Table 15: Error Message: XUDT UDT Conversion.........................................................................54Table 16: Non Feature-Related Error Messages..............................................................................54Table 17: EAGLE 5 ISS Card Overview Table.................................................................................58Table 18: Hardware Baseline.............................................................................................................63

v910-6006-001 Revision E, August 2012

EAGLE 5 ISS Release 43.0

Feature Content

Introduction

Feature notices are distributed to customers with each new release of software.

This Feature Notice includes a brief overview of each feature, lists new hardware required (if any),provides the hardware baseline for this release, and explains how to find the Release Notice and othercustomer documentation on the Customer Support Site.

Revision E contains one update to the material released in Revision D:

The PC_TYPE in Daily Maintenance and Hourly Maintenance Per SSP reports section is added.

New and Enhanced Features

• 3 Links per E5-ATM Card

The E5-ATM card can support up to 3 ATM links.• 10,000 Routesets

Up to 10,000 routesets or destinations can be provisioned on the system. The maximum numberof supported aliases and exception list entries is also increased to 10,000, each.

• Additional DRA values for INP formatting

The INP and AINPQ features are enhanced to support additional DRA values.• Fall-back to GTT after LNP MR Service

Global Title Translation (GTT) can be performed on MSUs that are relayed by certain LNP MRservices.

• G-Flex MLR Support for Additional OpCodes

The G-Flex Map Layer Routing feature is enhanced to support additional MAP Operations.• Hybrid INP/IDP Relay Service

The Prepaid IDP Query Relay feature is enhanced to send CONNECT, CONTINUE, orRELEASECALL responses based on the RTDB lookup results using INP functionality.

In addition, a Service Control Point (SCP) Global Title Address (GTA) can be provisioned basedon a Service Key. This functionality allows Global Title Translation to be used to route an IDP orIDPSMS message to the provisioned SCP GTA.

• Multiple IDP Relay Instances

The Prepaid IDP Query Relay feature is enhanced to support up to 4 IDPRCDPN(X) NPP servicesfor Called Party modifications. Each service can be configured separately to process an incomingIDP message in a different way.

6910-6006-001 Revision E, August 2012

• Point Code and CIC Translation

The system can change the destination point code, originating point code, and circuit identifiercode of an MTP-routed MSU to previously-configured values. This ability allows the system toemulate a point code using other nodes in the network.

• Pre-LNP Query Service GTT processing

GTT can be performed on messages that are destined for certain LNP Query services before themessages are processed by the LNP local subsystem.

• Support CRP check for SRI_SM using TCAP digits

The MSISDN digits in the TCAP layer of SRI_SM messages can be used as the Directory or DialedNumber for MNP Circular Route Prevention processing performed by the MT-Based GSM SMSNP feature.

• XUDT Conversion Enhancements

A new XUDT UDT Conversion feature is introduced to allow XUDT(S) < - > UDT(S) conversionto occur based on the Destination Point Code (DPC).

In addition, the existing ANSI-ITU-China SCCP Conversion feature (now referred to as theANSI/ITU SCCP Conversion feature) can support XUDT(S) conversion for MTP-routed andGT-routed SCCP messages.

Other Changes

• Change the number of digits in the MAP Routing Info of the returned SRI_ACK message to 15

The number of digits in the MAP Routing Info portion of the returned SRI_ACK message can be

configured by the user.• E5-TDM does not support Hardware Flow Control

Documentation for the chg-trm command is updated to note that the E5-TDM card does notsupport hardware flow control on the serial MMI port.

• Extended Processing Time Notification

The rept-stat/rtrv-dstn and rept-stat/rtrv-rte commands are updated to display thewarning "Extended processing time may be required" before more than one destination or routestatus is displayed.

• PC_TYPE in Daily Maintenance and Hourly Maintenance Per SSP reports

The new field PC_TYPE is added to the Daily Maintenance (MTCD) and Hourly Maintenance(MTCH) Per SSP reports for enttype=aiq, atinpq, lnp, np, or vflex.

• Support for the BLIXP GPL

A new BLIXP flash GPL is introduced. This GPL contains a tar image with all of the previouslyindependent flash GPLs required for E5-E1T1, E5-ENET, E5-SM4G, and HC-MIM cards.

• Update to the msucount Command

The msucount command output is updated to provide greater readability.• Update to the netstat Command

The netstat -I command output for non-E5 cards is updated to provide greater readability.• Update to rept-imt-lvl2 Command


EAGLE 5 ISS Release 43.0Release 43.0 Feature Notice

The rept-imt-lvl2 command output is updated to provide greater readability.• Update to the rept-stat-imt Command

The rept-stat-imt command output is updated to display the IMT system alarms.• Update to the rept-stat-rtkey Command

The rept-stat-rtkey command output is updated to provide greater readability.

3 Links per E5-ATM Card

The 3 Links per E5-ATM Card feature allows the E5-ATM card to support a maximum of 3 ATM links.The third link is referred to as link A1 and can be assigned to the third port on an E5-ATM card. TheE5-ATM card must be re-loaded before link A1 can be supported.

The 3 Links per E5-ATM Card feature is a quantity feature with part numbers ranging from 893-0391-01to 893-0391-77. Each quantity FAK supports the feature in the increment of 5 E5-ATM cards.

Feature Control Requirements

• FAK for Part Number in the range 893-0391-01 to 893-0391-77. Each FAK enables the 3 Links perE5-ATM Card feature for an increment of 5 E5-ATM cards.

• Any ATM link provisioned on the system must have a VCI value less than or equal to 16383 beforethe feature can be enabled.

• A temporary FAK cannot be used to enable the feature.• After a feature quantity is enabled, the default status of the feature is ON. A feature cannot be

turned off after being turned on.• After a feature quantity is enabled, a feature with a lower quantity cannot be enabled.

Hardware Requirements

None.

Commands

• enable/rtrv-ctrl-feat—Enhanced to enable and display the status of the 3 Links per E5-ATMCard quantity feature.

rtrv-ctrl-feat

rlghncxa03w 10-11-03 16:40:40 EST EAGLE 43.0.0

The following features have been permanently enabled: Feature Name Partnum Status Quantity HC-MIM SLK Capacity 893012707 on 64 Command Class Management 893005801 on ---- LNP Short Message Service 893006601 on ---- Prepaid SMS Intercept Ph1 893006701 on ---- Intermed GTT Load Sharing 893006901 on ---- MNP Circ Route Prevent 893007001 on ---- XGTT Table Expansion 893006101 on 400000 XMAP Table Expansion 893007710 on 3000 Large System # Links 893005911 on 2800



Routesets 893006403 on 8000 EAGLE5 Product 893007101 on ---- EAGLE Product 893007201 off ---- IP7 Product 893007301 off ---- Network Security Enhance 893009101 off ---- Telnet 893005701 on ---- SCCP Loop Detection 893016501 off ---- LNP ELAP Configuration 893010901 on ---- LNP ported TNs 893011036 on 384000000 LNP ported LRNs 893010501 on 200000 LNP ported NPANXXs 893009402 on 350000 15 Minute Measurements 893012101 off ---- EIR 893012301 on ---- EAGLE OA&M IP Security 893400001 off ---- SCCP Conversion 893012001 on ---- SE-HSL SLK Capacity 893013005 on 32 3 Links per E5-ATM Card 893039101 on 5

;

• ent/rept-stat/rtrv-slk—Enhanced to support the A1 link for an E5-ATM card.

rtrv-slk:loc=1306:link=a1

tekelecstp 10-11-18 12:17:00 EST EAGLE 43.0.0 LP ATM LOC LINK LSN SLC TYPE SET BPS TSEL VCI VPI LL 1306 A1 ls1 1 LIMATM 1 1.544M LINE 5 0 0

• rept-stat-card—Enhanced to support the A1 link for the E5-ATM card.

rept-stat-card:loc=1207:mode=full

eagle1 10-11-18 00:41:18 EST 43.0.0 CARD VERSION TYPE GPL PST SST AST 1207 024-038-000 LIMATM ATMHC IS-NR Active ----- ALARM STATUS = * 0021 Clock A for card failed, Clock B normal IMTPCI GPL version = 133-034-000 BLVXW6 GPL version = 133-033-000 BLDIAG6 GPL version = 133-032-000 BLBEPM GPL version = 128-021-000 BLCPLD GPL version = 133-018-000 IMT BUS A = Conn IMT BUS B = Conn CLOCK A = Fault CLOCK B = Active CLOCK I = Idle HS CLOCK A = Fault HS CLOCK B = Fault HS CLOCK I = Idle MBD BIP STATUS = Valid MOTHER BOARD ID = EPM A DBD STATUS = Valid DBD TYPE = ATM DBD MEMORY SIZE = 512M HW VERIFICATION CODE = ---- CURRENT TEMPERATURE = 48C (119F) PEAK TEMPERATURE: = 49C (121F) [02-01-01 00:34] SIGNALING LINK STATUS SLK PST LS CLLI A OOS-MT ls8 ----------- B OOS-MT ls7 ----------- A1 OOS-MT ls8 ----------- TVG STATUS SNM TVG RESULT = 24 hr: ------, 5 min: ------ SLAN TVG RESULT = 24 hr: ------, 5 min: ------



SCCP TVG RESULT = 24 hr: ------, 5 min: ------ INM TVG RESULT = 24 hr: ------, 5 min: ------

Command Completed.;

Limitations

No limitations are associated with this feature.

10,000 Routesets

The 10,000 Routesets feature allows up to 10,000 routesets or destinations to be provisioned on theEAGLE 5 ISS. The maximum number of supported aliases and exception list entries are increased to10,000, each. The maximum number of supported normal and exception routes (combined) is increasedto 10,000.

An additional 500 entries continue to be supported for dynamically-created exception list entries.These entries are available only if the Cluster Routing feature is turned on.


• FAK for Part Number 893-0064-05• The 5000 Routesets feature must be turned on before the 10,000 Routesets feature can be enabled.• The Cluster Routing feature must be turned on before the additional 500 entries that are reserved

for dynamically-created entries are available.• A temporary FAK cannot be used to enable the 10,000 Routesets feature.• The 10,000 Routesets feature cannot be turned off after being turned on.


The 10,000 Routesets feature is supported on all cards except EOAM cards.

Commands

• chg/rtrv-stpopts—Enhanced to support 10,000 destination point codes.• enable/rtrv-ctrl-feat—Enhanced to enable and display the status of the 10,000 Routesets

feature.

rtrv-ctrl-feat


The following features have been permanently enabled: Feature Name Partnum Status Quantity HC-MIM SLK Capacity 893012707 on 64 Command Class Management 893005801 on ---- LNP Short Message Service 893006601 on ---- MNP Circ Route Prevent 893007001 on ---- XGTT Table Expansion 893006101 on 400000 XMAP Table Expansion 893007710 on 3000



Large System # Links 893005911 on 2800 Routesets 893006405 on 10000 EAGLE5 Product 893007101 on ---- EAGLE Product 893007201 off ---- IP7 Product 893007301 off ---- Network Security Enhance 893009101 off ---- Telnet 893005701 on ---- Port Chk for MO SMS 893009301 on ---- SCCP Loop Detection 893016501 off ---- LNP ELAP Configuration 893010901 on ---- LNP ported TNs 893011036 on 384000000 LNP ported LRNs 893010501 on 200000 LNP ported NPANXXs 893009402 on 350000 15 Minute Measurements 893012101 off ---- EIR 893012301 on ---- EAGLE OA&M IP Security 893400001 off ----

;

• ent/chg/dlt/rtrv-dstn—Enhanced to support 10,0000 destinations.

Example 1 shows output when the NCR, NRT, CRMD, and 10,000 Routesets features are turnedon.rtrv-dstn


DPCA CLLI BEI ELEI ALIASI ALIASN/N24 DMN 003-003-003 ----------- no --- -------------- -------------- SS7 004-004-004 ----------- no --- -------------- -------------- SS7 005-005-005 ----------- no --- -------------- -------------- SS7 008-001-* ----------- no no -------------- -------------- SS7

DESTINATION ENTRIES ALLOCATED: 10000 FULL DPC(s): 9 NETWORK DPC(s): 0 CLUSTER DPC(s): 1 TOTAL DPC(s): 10 CAPACITY (% FULL): 1% ALIASES ALLOCATED: 10000 ALIASES USED: 0 CAPACITY (% FULL): 0% X-LIST ENTRIES ALLOCATED: 500;

Example 2 shows output when the CRMD, NCR, and NRT features are off and the 10,000 Routesetsfeature is turned on.rtrv-dstn

rlghncxa03w 10-08-17 08:29:15 EST EAGLE 43.0.0 Destination table is (10 of 10000) 1% full Alias table is (8 of 10000) 1% full RTRV-DSTN: MASP A – COMPLTD;

• rept-stat-sys—Enhanced to support the 10,000 Routesets feature.• rtrv-tbl-capacity—Enhanced to support the 10,000 Routesets feature.

rtrv-tbl-capacity


DSTN table is ( 600 of 10000) 6% full XLIST table is ( 0 of 500) 0% full



SPC table is ( 0 of 40) 0% full LS table is ( 512 of 1024) 50% full SLK table is ( 1501 of 2800) 54% full IP-LNK table is ( 0 of 512) 0% full IP-HOST table is ( 0 of 2048) 0% full MAP table is ( 1500 of 36000) 5% full MRN table is ( 0 of 3000) 0% full SCCPSRV table is ( 0 of 384) 0% full GTA table is ( 0 of 269999) 0% full GTT-SET table is ( 10 of 2000) 1% full SSNSELID table is ( 0 of 100000) 0% full SCRSET table is ( 25 of 255) 10% full RTEKEY table is ( 0 of 1000) 0% full APPLSOCK table is ( 0 of 4000) 0% full AS table is ( 0 of 250) 0% full VFLXCD table is ( 1 of 4950) 1% full VFLXRN table is ( 1 of 10000) 1% full VFLXVID table is ( 1 of 1000) 1% full NPP-AS table is ( 0 of 1024) 0% full NPP-SRS table is ( 0 of 8192) 0% full GTT-ACT table is ( 0 of 2000) 0% full GTT-ASET table is ( 0 of 20000) 0% full GTMOD table is ( 1 of 100000) 1% full GTT-PATH table is ( 3 of 10000) 1% full

;

Limitations


Additional DRA values for INP formatting

The existing INP (Part Number 893-0179-01) and AINPQ (Part Number 893-0178-01) features areenhanced to support additional DRA values:

• GRN• GRN+DN• CC+GRN+DN


None.


There are no feature control requirements identified for this feature.

Commands

• chg/rtrv-ainpopts—Enhanced to provision and display additional DRA values.• chg/rtrv-inpopts—Enhanced to provision and display additional DRA values.



Limitations


Fall-back to GTT after LNP MR Service

The Fall-back to GTT after LNP MR Service feature allows Global Title Translation (GTT) to beperformed on MSUs after the MSUs are processed by LNP MR services. GTT is used to determine thealternative database node for optimal routing. The LIDB, CLASS, CNAM, ISVM, and WSMSC LNPMR services are supported.


The EGTT feature must be turned on before the Fall-back to GTT after LNP MR Service functionalitycan be provisioned.


The Fall-back to GTT after LNP MR Service functionality requires an E5-SM4G or higher card.

Commands

The ent/chg/dlt/rtrv-lnp-serv commands are enhanced to provision and display the optionsallowing Fall-back to GTT after LNP MR service.

rtrv-lnp-serv

rlghncxa03w 10-11-11 13:45:15 EST EAGLE 43.0.0 SERV TT TTN DV ALIAS GTTRQD SELID DFLTACT CNAM 1 cnam1 SCCP --- On 10 fallback 8 On 20 discact LIDB 2 lidb1 SCCP --- Off None discact 19 On None falltogtt AIN 3 ain TCAP --- Off None fallback UDF1 22 udf1 TCAP --- --- --- ---

LNP-SERV TABLE IS 2% FULL (6 of 256) ;

Limitations


G-Flex MLR Support for Additional OpCodes

The existing G-Flex Map Layer Routing (G-Flex MLR) feature (Part Number 893-0217-01) is enhancedto support additional MAP Operations:



Table 1: New MAP Operations Supported by the G-Flex MLR Feature

MAP Operation NameMAP Message DescriptionMAP Opcode

registerSSRegister Supplementary Service10

activateSSActivate Supplementary Service12

deactivateSSDeactivate SupplementaryService

13

interrogateSSInterrogate SupplementaryService

14

authenticationFailureReportAuthentication Failure Report15

restoreDataRestore Data57

processUnstructuredSS-RequestProcess Unstructured SS Request59

readyForSMReady for Short Message66

purgeMSPurge Mobile Subscriber67

sendRoutingInfoFor LCSSend Routing Information forLoCation Service

85

This enhancement also allows the G-Flex MLR feature to use the MSISDN from the MAP layer if theIMSI is not available for routing Process Unstructured SS Request and sendRoutingInfoForLCSmessages.


No additional feature control requirements are required for this enhancement.


No additional hardware is required for this enhancement.

Commands

The chg/rtrv-gsmopts commands are updated to provision and display the additional MAPoperations that can be supported by the G-Flex MLR feature.

rtrv-gsmopts

tekelecstp 11-01-11 16:12:11 EST EAGLE 43.0.0 GSM OPTIONS ---------------------------- MULTCC = NONE MULTCC = NONE MULTCC = NONE MULTCC = NONE MULTCC = NONE MULTCC = NONE MULTCC = NONE MULTCC = NONE MULTCC = NONE MULTCC = NONE DEFMAPVR = 1

DEFMCC = NONE DEFMNC = NONE CCNC = NONE MCCMNC = NONE CCNC = NONE MCCMNC = NONE



CCNC = NONE MCCMNC = NONE CCNC = NONE MCCMNC = NONE CCNC = NONE MCCMNC = NONE CCNC = NONE MCCMNC = NONE CCNC = NONE MCCMNC = NONE CCNC = NONE MCCMNC = NONE CCNC = NONE MCCMNC = NONE CCNC = NONE MCCMNC = NONE

SRIDN = TCAP SRIDNNOTFOUND = GTT CRPTT = NONE SRISMGTTRTG = OFF MSRNDIG = RN MSRNNAI = 0 MSRNNP = 0 MSISDNTRUNC = 0 SRFADDR = NONE SRFNAI = 0 SRFNP = 0 MSRNLEN = 30

SERVERPFX = NONE GSM2IS41 = NONE MIGRPFX = SINGLE IS412GSM = NONE

SPORTTYPE = NONE DFLTRN = NONE

EIRGRSP = OFF EIRRSPTYPE = TYPE1 EIRIMSICHK = OFF

ENCODECUG = OFF ENCODENPS = ON ENCDNPSPTNONE = OFF ENCDNPSDNNOTFOUND= OFF

G-Flex MLR OPTIONS : GFLEXMAPLAYERRTG = NONE

REGSS = OFF ACTSS = OFF DACTSS = OFF INTSS = OFF AUTHFAILRPT = OFF RSTDATA = OFF PROCUNSTRQT = OFF RDYFORSM = OFF PURGMOBSS = OFF SRILOC = OFF

;

Limitations


Hybrid INP/IDP Relay Service

The Hybrid INP/IDP Relay Service feature allows the existing Prepaid IDP Query Relay feature (PartNumber 893-0160-01) to send CONNECT, CONTINUE, or RELEASECALL responses based on theRTDB lookup results. This functionality includes the ability to configure whether the CutAndPasteparameter is included in the CONNECT message when the message is sent from the Prepaid IDPQuery Relay feature.

The functionality is configured for the Prepaid IDP Query Relay feature using a new INPRTG ServiceAction, which is applicable to the IDPRCDPN(X) and IDPRCGPN NPP services. Refer to the NumberingPlan Processor (NPP) Overview for more information.

The Hybrid INP/IDP Relay Service feature also allows a Service Control Point (SCP) Global TitleAddress (GTA) to be provisioned based on a Service Key. This functionality is configured using a newSKGTARTG Service Action which is applicable to IDPRCDPN(x) services. This Service Action allows



the IDP message to be routed to the provisioned SCP GTA. If the functionality is not configured, thenthe message is routed to the incoming SCCP Called Party Address (CdPA) GTA.

Note: If both A-Party Routing and Service Key based GTA routing are configured, then the ServiceKey based GTA routing takes precedence.


The Prepaid IDP Query Relay feature must be enabled before the Service Key based GTA routingfunctionality can be provisioned.


None.

Commands

• chg/rtrv-measopts—Enhanced to support the SYSTOT-IDPR report.

Note: The SYSTOT-IDPR report is supported by provisioning a systotidpr option in thechg-measopts command. This option can be turned on or off as a member of a comma-separatedmnemonic list (chg-measopts:on=systotidpr, chg-measopts:off=systotidpr). As ofRelease 43.0, the systotidpr option is the only option that can be configured as part of thecomma-separated list.

rtrv-measopts

tekelecstp 10-12-06 15:03:36 EST EAGLE 43.0.0

PLATFORMENABLE = off COLLECT15MIN = off CLLIBASEDNAME = off OAMHCMEAS = off ---------------------- SYSTOTSTP = off SYSTOTTT = off SYSTOTSTPLAN = off SYSTOTIDPR = off COMPLINK = off COMPLNKSET = off COMPSCTPASOC = off COMPSCTPCARD = off COMPUA = off GTWYSTP = off GTWYLNKSET = off GTWYORIGNI = off GTWYORIGNINC = off GTWYLSORIGNI = off GTWYLSDESTNI = off GTWYLSONISMT = off NMSTP = off NMLINK = off NMLNKSET = off AVLLINK = off AVLSTPLAN = off AVLDLINK = off ;

• chg/rtrv-npp-serv—Enhanced to support the SKGTARTG and INPRTG Service Actions.



rtrv-npp-serv


SERVICE STATUS SA PRECEDENCE ------------------------------------------ nppt off rtdbtrnsp 100 rtdbtrn 50 rtdbtsp 50 cdial 10

SERVICE STATUS SA PRECEDENCE ------------------------------------------ tif off cdial 10 fwdscs 5 crp 92 npnrls 91 nprelay 80 nprls 80 snscgpn 75 cgpnsvcrqd 80 asdlkup 90 grnlkup 90 cgpnasdrqd 90 cgpngrnrqd 90 nscdpn 80 nscgpn 75

SERVICE STATUS SA PRECEDENCE ------------------------------------------ tif2 off cdial 10 fwdscs 5 crp 92 npnrls 91 nprelay 80 nprls 80 snscgpn 75 cgpnsvcrqd 80 asdlkup 90 grnlkup 90 cgpnasdrqd 90 cgpngrnrqd 90 nscdpn 80 nscgpn 75

SERVICE STATUS SA PRECEDENCE ------------------------------------------ tif3 off cdial 10 fwdscs 5 crp 92 npnrls 91 nprelay 80 nprls 80 snscgpn 75 cgpnsvcrqd 80 asdlkup 90 grnlkup 90 cgpnasdrqd 90 cgpngrnrqd 90 nscdpn 80 nscgpn 75

SERVICE STATUS SA PRECEDENCE ------------------------------------------ idprcdpn off cdial 10



ccncchk 100 cdpnnp 80 lacck 60 cgpnsvcrqd 60 asdlkup 50 grnlkup 50 cgpnasdrqd 50 cgpngrnrqd 50 inprtg 95 skgtartg 50

SERVICE STATUS SA PRECEDENCE ------------------------------------------ idprcgpn off cdial 10 cgpnnp 80 asdlkup 50 grnlkup 50 blklstqry 90 blklstrly 90 cgpnrtg 70 inprtg 95

SERVICE STATUS SA PRECEDENCE ------------------------------------------ mosmsicdpn off cdial 10 cdpnnp 60 asdlkup 50 grnlkup 50 cgpnasdrqd 50 cgpngrnrqd 50 migrate 70

SERVICE STATUS SA PRECEDENCE ------------------------------------------ mosmsicgpn off cdial 10 asdlkup 50 grnlkup 50

SERVICE STATUS SA PRECEDENCE ------------------------------------------ mosmsgcdpn off cdial 10 cdpnnp 60 asdlkup 50 grnlkup 50 cgpnasdrqd 50 cgpngrnrqd 50 pprelay 80

SERVICE STATUS SA PRECEDENCE ------------------------------------------ mosmsgcgpn off cdial 10 asdlkup 50 grnlkup 50 pprelay 80 fraudchk 90

SERVICE STATUS SA PRECEDENCE ------------------------------------------ iarcdpn off cdial 10 ccncchk 100 cdpnnp 80 cgpnsvcrqd 60 asdlkup 50 grnlkup 50 cgpnasdrqd 50



cgpngrnrqd 50

SERVICE STATUS SA PRECEDENCE ------------------------------------------ iarcgpn off cdial 10 cgpnnp 80 asdlkup 50 grnlkup 50

SERVICE STATUS SA PRECEDENCE ------------------------------------------ idprcdpn2 off cdial 10 ccncchk 100 cdpnnp 80 lacck 60 cgpnsvcrqd 60 asdlkup 50 grnlkup 50 cgpnasdrqd 50 cgpngrnrqd 50 inprtg 95 skgtartg 50



;

• chg/rtrv-ttropts—Enhanced to provision options for the CONNECT, CONTINUE, andRELEASECALL messages that can be sent by the Prepaid IDP Query Relay feature.

rtrv-ttropts


TTR OPTIONS ----------------------------------------------------- CDPN DETAILS CGPN DETAILS NPTYPE rnsp CGNPTYPE rnsp SNAI incoming CGSNAI incoming



CGPACCCK nonintl DLMA NONE DLMB NONE DLMC NONE DFLTRN NONE SPORTTYPE none SPFILL off RNSPFILL off CGPNSKRTG no DRAFRMT grn DRANAI 3 CDRNRSP connect CDSPRSP relay CDNOENTITYRSP continue CDDNNOTFNDRSP release CDDRA rndn CDDRANAI NATL CDDRANP E164 CDRELCAUSE 31 CDCNP OFF CGRNRSP connect CGSPRSP relay CGNOENTITYRSP continue CGDNNOTFNDRSP release CGDRA rndn CGDRANAI NATL CGDRANP E164 CGRELCAUSE 31 CGCNP OFF

;

• ent/chg/dlt/rtrv-csl—Enhanced to provision the SCP GTA.

Example 1 displays the output when all CSLs are requested:rtrv-csl


Prepaid IDP Query Relay CC+NC List DS

--------------- 000015 000025

CC+NC List ( 2 of 20) 10%

Prepaid IDP Query Relay GT List DS CDPN BCD

--------------- ---------- 1234567815 0

GT List ( 1 of 500) 1%

Prepaid IDP Query Relay SK+BCSM List DS PT IDPRCDPN SCPGTA

--------------- ---------- ---------- --------------------- 0000000123 prepaidno idprcdpn 0000000014



0000000143 prepaidno idprcdpn 0000000014 1234567815 prepaidno idprcdpn3 1234 123456782e prepaidno idprcdpn NONE 1234567890 prepaidno idprcdpn NONE

SK+BCSM List ( 5 of 150) 3%

IDP Screening for Prepaid SK+TS List DS

--------------- 0025 0569 1529

SK+TS List ( 3 of 25) 12%

IDP Screening for Prepaid INSL List DS

--------------- 0029 0048 0148

INSL List ( 3 of 50) 6%

;

Example 2 displays the output when CSL information for the Prepaid IDP Query Relay feature isrequested.rtrv-csl:feature=”Prepaid IDP Query Relay”


Prepaid IDP Query Relay CC+NC List DS

--------------- 000015 000025

CC+NC List ( 2 of 20) 10%

Prepaid IDP Query Relay GT List DS CDPN BCD

--------------- ---------- 1234567815 0

GT List ( 1 of 500) 1%


--------------- ---------- ---------- --------------------- 0000000123 prepaidno idprcdpn 0000000014 0000000143 prepaidno idprcdpn 0000000014 1234567815 prepaidno idprcdpn3 1234 123456782e prepaidno idprcdpn NONE



1234567890 prepaidno idprcdpn NONE


;

Example 3 displays the output when Service Control Point information is requested.rtrv-csl:scpgta=0000000014



--------------- ---------- ---------- --------------------- 0000000123 prepaidno idprcdpn 0000000014 0000000143 prepaidno idprcdpn 0000000014


;

• ent/chg/dlt/rtrv-npp-as—Enhanced to provision INP functionality for the Prepaid IDPQuery Relay feature using the new SKGTARTG and INPRTG Service Actions.

• rept-ftp-meas—Enhanced to support measurements for IDPR.• rept-meas—Enhanced to support measurements for IDPR.

Measurements

A new SYSTOT-IDPR report is added for the registers associated with the Hybrid INP/IDP RelayService feature and the Multiple IDP Relay Instances feature. This report can be generated using theMeasurements Control Platform, OAM-based, or E5-OAM Integrated Measurements collection method.

The SYSTOT-IDPR report contains the following new registers for the Hybrid INP/IDP Relay Servicefeature:

• IDPINPRTG(X)—number of IDP MSUs processed by the INPRTG Service Action from thecorresponding IDPRCDPN(X) services

• IDPINPCONN(X)—number of IDP MSUs for which the INPRTG Service Action sent a CONNECTmessage from the corresponding IDPRCDPN(X) services

• IDPINPCONT(X)—number of IDP MSUs for which the INPRTG Service Action sent a CONTINUEmessage from the corresponding IDPRCDPN(X) services

• IDPINPRLC(X)—number of IDP MSUs for which the INPRTG Service Action sent a RELEASECALLmessage from the corresponding IDPRCDPN(X) services

• IDPSKGTART(X)—number of IDP/IDPSMS MSUs for which the SKGTA Service Action is invokedfor IDPRCDPN(X) services

Limitations




Multiple IDP Relay Instances

The Multiple IDP Relay Instances feature allows the existing Prepaid IDP Query Relay feature (PartNumber 893-0160-01) to support up to 4 IDPRCDPN NPP services (IDPRCDPN, IDPRCDPN2,IDPRCDPN3, and IDPRCDPN4) for Called Party modifications. Each service can be configuredseparately to process an incoming IDP message in a different way. Refer to the Numbering Plan Processor(NPP) Overview for more information.

Note: The combined services are referred as IDPRCDPN(X) unless a specific service must be specified.


At least one of the IDPRCDPN(X) services must be configured before the Prepaid IDP Query Relayfeature can be turned on.


None.

Commands

• chg/rtrv-measopts—Enhanced to support the SYSTOT-IDPR report. See the Commands sectionfor the Hybrid INP/IDP Relay Service feature for an example of the rtrv-measopts output.

• ent/chg/dlt/rtrv-npp-as—Enhanced to support the SKGRTG and INPRTG Service Actionsfor the IDPRCDPN(X) services.

• chg/rtrv-npp-serv—Enhanced to support the IDPRCDPN(X) NPP services. See the Commandssection for the Hybrid INP/IDP Relay Service feature for an example of rtrv-npp-serv output.

• chg/rtrv-ttropts—Enhanced to support the IDPRCDPN(X) NPP services. See the Commandssection for the Hybrid INP/IDP Relay Service feature for an example of rtrv-ttropts output.

• enable/chg-ctrl-feat—Enhanced to require one of the IDPRCDPN(X) NPP services to beprovisioned before the Prepaid IDP Query Relay feature can be turned on.

• ent/chg/dlt-npp-srs—Enhanced to support the IDPRCDPN(X) NPP services.• ent/chg/dlt/rtrv-csl—Enhanced to support the IDPRCDPN(X) services. See the Commands

section for the Hybrid INP/IDP Relay feature for examples of rtrv-csl output.• rept-ftp-meas—Enhanced to support measurements for IDPR.• rept-meas—Enhanced to support measurements for IDPR.

Measurements

The IDPRCDPN(X) register is reported in the SYSTOT-IDPR report. This register tracks the numberof IDP/IDPSMS MSUs processed per IDPRCDPN(X) NPP service.

See the Measurements section for the Hybrid INP/IDPR Relay feature for a description of theSYSTOT-IDPR report.

Limitations




Point Code and CIC Translation

The Point Code and CIC Translation (PCT) feature allows the EAGLE 5 ISS to change the destinationpoint code (DPC) or originating point code (OPC) of an MTP-routed MSU to previously configuredvalues. This functionality allows external networks to continue using the old point codes by emulatingand mapping them to the new real point codes within the networks. The feature can also be used tochange the circuit identifier code (CIC) of the MSU.

Note: ITUN24 point codes, spare point codes, and private point codes are not supported by PCTtranslations.

A new PCT table is used to define translations between real and emulated point codes.

Network nodes can send and receive traffic to and from the emulated point code (EPC) without'knowing' the real point code (Real PC) that is being emulated by the EPC. This ability allows the RealPC to be changed transparently from the rest of the network, which can continue using the EPC toroute traffic.

If PCT is configured, either system wide or for the incoming linkset, then a DPC lookup is performedon the incoming MSU. If a translation is found during the DPC lookup, then the DPC of the MSU isreplaced by the Real PC as the MSU is received by the EAGLE 5 ISS. If a Real CIC was provisioned inthe translation, then the CIC of the MSU is changed to the value from the Real CIC range.

If the MSU was not modified by the DPC lookup, then an OPC lookup is performed on the outgoingMSU. If a translation is found during the OPC lookup, then the OPC of the MSU is replaced by theEPC of the matching translation as the MSU leaves the EAGLE 5 ISS. If an Emulated CIC wasprovisioned in the translation, then the CIC of the MSU is changed to the value from the EmulatedCIC range.

Features and functionalities in the EAGLE 5 ISS use the real point code in provisioning.

The PCT feature is a quantity feature. The quantity is used to define the maximum number of allowedtranslations.


• FAK for the Part Number of the desired quantity feature:

• 893-0372-01—25 translations• 893-0372-02—50 translations• 893-0372-03—75 translations• 893-0372-04—100 translations• 893-0372-05—150 translations• 893-0372-06—200 translations• 893-0372-07—250 translations• 893-0372-08—1000 translations

• After a PCT feature has been enabled, a PCT feature with a lower quantity cannot be enabled.• A temporary FAK cannot be used to enable the feature.




The pct pass command is not supported on E1/T1 MIM, E1-ATM, LIM-ATM, and MPL cards.

Commands

• chg-lsopts—Enhanced to allow point code translation to be applied to MSUs on links of aspecified linkset. The status of this functionality is displayed in the rtrv-ls command.

• chg/rtrv-stpopts—Enhanced to apply point code translation to all or selected MSUs.

rtrv-stpopts

rlghncxa03w 10-08-17 16:02:05 EST EAGLE 43.0.0 STP OPTIONS --------------------------- MTPT31CTL 1 MTPLTI yes MTPLTCTDPCQ 3 MTPLTST 10000 MTPXLQ 500 MTPXLET 0100 MTPXLOT 90% MTPDPCQ 8000 TFATFRPR 1000 MTPRSI yes MTPRSIT 5000 MTPLPRST yes MTPT10ALT 30000 UIMRD yes SLSCNV perls CRITALMINH yes DISPACTALMS no NPCFMTI 14-0-0-0 GSMDFLT PASS GSMDECERR PASS DEFCC 49 DEFNDC 177 DSMAUD no RPTLNPMRSS yes RANDSLS all RSTRDEV on SECMTPMATE off SECMTPSID off SECMTPSNM notify SECSCCPSCMG notify CNVCGDA yes CNVCGDI yes CNVCGDN yes CNVCGDN24 yes GTCNVDFLT yes ANSIGFLEX yes HSCLKSRC RS422 HSCLKLL LONGHAUL ARCHBLDID off PCT on;

• dlt-rte—Enhanced to prevent the last route to a destination point code that exists in the PCTtable from being deleted until the Filter Point Code or the Real Point Code is deleted from the table.

• enable/rtrv-ctrl-feat—Enhanced to support the PCT feature.



rtrv-ctrl-feat


The following features have been permanently enabled: Feature Name Partnum Status Quantity HC-MIM SLK Capacity 893012707 on 64 Command Class Management 893005801 on ---- LNP Short Message Service 893006601 on ---- MNP Circ Route Prevent 893007001 on ---- XGTT Table Expansion 893006101 on 400000 XMAP Table Expansion 893007710 on 3000 Large System # Links 893005911 on 2800 Routesets 893006403 on 8000 EAGLE5 Product 893007101 on ---- EAGLE Product 893007201 off ---- IP7 Product 893007301 off ---- Network Security Enhance 893009101 off ---- Telnet 893005701 on ---- 15 Minute Measurements 893012101 off ---- EIR 893012301 on ---- EAGLE OA&M IP Security 893400001 off ---- Spare Point Code Support 893013601 on ---- PC & CIC Translation 893037201 on 1000

;

• ent/dlt/rtrv-pct—Added to provision and display point code and CIC translation data.

rtrv-pct


EPCA FILTPCA REALPCA SI SSN RELCAUSE 001-001-001 * 002-002-002 4 --- 10

ECICS = 10 ECICE = 20 RCICS = 30 RCICE = 40

EPCI FILTPCI REALPCI SI SSN RELCAUSE 1-001-2 2-002-2 2-002-2 3 10 ---

ECICS = ---------- ECICE = ---------- RCICS = ---------- RCICE = ----------

EPCN FILTPCN REALPCN SI SSN RELCAUSE 00300 * 00200 * --- ---

ECICS = ---------- ECICE = ---------- RCICS = ---------- RCICE = ----------

PCT table is (3 of 1000) 1% full.

;

• pct—Added to maintain per-translation statistics and to test PCT functionality. The pct commandcan be operated in Stats or Test mode. In Stats mode, the command is used to reset or displayper-translation statistics. In Test mode, the command is used to test PCT behavior for a messagewith the specified field values.

Example 1 shows output for the PCT help command.



pass:loc=1201:cmd="pct -h"

Command Accepted – Processing

Usage: pct -m stats [-l | -r] [-p pctype] [-e epc] [-f fpc] [-a realpc] [-s si] [-u ssn] [-c cicr] pct -m test [-p pctype] -d dpc -o opc -s si [-c cic] [-u ssn] pct -h Modes: stats - reset or display per-rule stats test - test PCT behavior for a message with the specified field values Common Options: -p pctype is ANSI, ITUI, or ITUN stats Mode Options: -r reset the stats for selected rules with no other options, resets stats on all rules if other options present, -e or -a must be supplied -l list the stats for selected rules (default) the -e or -a option must be supplied both -e and -a may be supplied -e emulated point code -a real point code -c cicr is in these forms: * (see Note 1) ecics-ecice:rcics-rcice, e.g., 5-10:15-20 ecics:rcics, e.g., 5:6 which is equiv to 5-5:6-6 allowed only if SI is 4, 5, or 13 -f filter pc; may be * (see Note 1) -s si; can be 0, 3, 4, 5, 13, or * (see Note 1) -u ssn; may be * (see Note 1) allowed only if SI is 3 test Mode Options: -d DPC in simulated MSU -o OPC in simulated MSU -s SI in simulated MSU -u SSN in CgPA and CdPA in simulated MSU; if absent and si is 3, indicates that route on SSN is off; allowed only if SI is 3 -c CIC in simulated MSU; required if SI is 4, 5, or 13 Notes: 1. an explicit * will match only with rule containing a wildcard; to match

on wildcard or a specific value, do not specify the associated option

Example 2 shows output for Stats mode.pass:loc=1201:cmd=”pct –m stats –l –e 4-3-1”


idx epc rpc fpc si ssn 6 004-003-001 007-003-001 007-002-030 3 24 dpclkp: 0 opclkp: 0 msudisc: 0 7 004-003-001 007-003-002 007-002-030 3 26 dpclkp: 0 opclkp: 0 msudisc: 0 8 004-003-001 007-003-006 007-002-030 5 --- ecic: 100-105 rcic: 200-205 dpclkp: 0 opclkp: 0 msudisc: 0 9 004-003-001 007-003-011 007-002-* 3 24 dpclkp: 0 opclkp: 0 msudisc: 0 10 004-003-001 007-003-016 007-*-* 3 24 dpclkp: 0 opclkp: 0 msudisc: 0 11 004-003-001 007-003-021 007-002-030 3 *



dpclkp: 0 opclkp: 0 msudisc: 0 12 004-003-001 007-003-026 007-002-030 5 --- dpclkp: 0 opclkp: 0 msudisc: 0 13 004-003-001 007-003-031 007-002-* 3 * dpclkp: 0 opclkp: 0 msudisc: 0 14 004-003-001 007-003-036 007-003-* 3 * dpclkp: 0 opclkp: 0 msudisc: 0 15 004-003-001 007-003-041 007-*-* 3 * dpclkp: 0 opclkp: 0 msudisc: 0 16 004-003-001 007-003-046 008-*-* 3 * dpclkp: 0 opclkp: 0 msudisc: 0 17 004-003-001 007-003-051 007-002-029 * --- dpclkp: 0 opclkp: 0 msudisc: 0 18 004-003-001 007-003-056 007-002-030 * --- dpclkp: 0 opclkp: 0 msudisc: 0 19 004-003-001 007-003-061 007-002-* * --- dpclkp: 0 opclkp: 0 msudisc: 0 20 004-003-001 007-003-066 007-*-* * --- dpclkp: 0 opclkp: 0 msudisc: 0 21 004-003-001 007-003-071 -------------- 3 24 dpclkp: 0 opclkp: 0 msudisc: 0 22 004-003-001 007-003-076 -------------- 5 --- ecic: 100-105 rcic: 200-205 dpclkp: 0 opclkp: 0 msudisc: 0 23 004-003-001 007-003-081 -------------- 3 * dpclkp: 0 opclkp: 0 msudisc: 0 24 004-003-001 007-003-086 -------------- 5 --- dpclkp: 0 opclkp: 0 msudisc: 0 25 004-003-001 007-003-091 -------------- * --- dpclkp: 0 opclkp: 0 msudisc: 0

Example 3 resets counters for all translations with the specified ANSI emulated point code.pass:loc=1201:cmd=”pct –m stats –l –r –e 4-3-1”


Stats reset on 20 rules

Example 4 shows a match on DPC lookup in Test mode.pass:loc=1201:cmd="pct -m test -d 4-3-1 -o 7-2-30 -s 3 -u 26"


Point Code and CIC Translation Lookup Test MSU content: OPC: 007-002-030 DPC: 004-003-001 SI: 3 SSN: 26 Lookup result: Match on DPC was found Matching entry: idx epc rpc fpc si ssn 7 004-003-001 007-003-002 007-002-030 3 26

Example 5 shows a match on OPC lookup in Test mode.pass:loc=1201:cmd="pct -m test -d 7-2-30 -o 7-3-2 -s 3 -u 26"


Point Code and CIC Translation Lookup Test MSU content: OPC: 007-003-002 DPC: 007-002-030 SI: 3



SSN: 26 Lookup result: Match on OPC was found Matching entry: idx epc rpc fpc si ssn 7 004-003-001 007-003-002 007-002-030 3 26

Example 6 shows a match on DPC lookup where the matching translation has a wildcard Filter PCand a wildcard SI in Test mode.pass:loc=1201:cmd="pct -m test -d 4-3-1 -o 9-9-9 -s 4 –c 106"


Point Code and CIC Translation Lookup Test MSU content: OPC: 009-009-009 DPC: 004-003-001 SI: 4 CIC: 106 Lookup result: Match on DPC was found Matching entry: idx epc rpc fpc si ssn 25 004-003-001 007-003-091 -------------- * ---

• rtrv-ls—Enhanced to display the status of PCT on a linkset.

Example 1 displays the output when the PCT feature is turned on.rtrv-ls:lsn=ls1


L3T SLT GWS GWS GWS LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS ls1 003-003-003 gws1 1 1 no A 15 on on on yes off

SPCA CLLI TFATCABMLQ MTPRSE ASL8 ---------------- ----------- 1 no no

RANDSLS off

IPSG IPGWAPC GTTMODE CGGTMOD PCT no no CdPA no off

L2T PCR PCR LOC PORT SLC TYPE SET BPS ECM N1 N2 1101 A 0 LIMDS0 1 56000 BASIC --- -----

LP ATM LOC PORT SLC TYPE SET BPS TSEL VCI VPI LL 1102 A 2 LIMATM 1 1.544M LINE 5 0 0

LOC PORT SLC TYPE IPLIML2 1201 A 5 IPLIM M2PA

L2T PCR PCR E1 E1 LOC PORT SLC TYPE SET BPS ECM N1 N2 LOC PORT TS 1205 A 6 LIME1 1 56000 BASIC --- ----- 1205 1 1

L2T PCR PCR T1 T1 LOC PORT SLC TYPE SET BPS ECM N1 N2 LOC PORT TS 1206 A 10 LIMT1 1 56000 BASIC --- ----- 1206 1 1



Link set table is (7 of 1024) 1% full.

;

Example 2 displays output when the FLOBR and PCT features are turned on.rtrv-ls:lsn=ls8


L3T SLT GWS GWS GWS LSN APCA (SS7) SCRN SET SET BEI LST LNKS ACT MES DIS SLSCI NIS ls8 001-001-001 none 1 1 no A 0 off off off no off

SPCA CLLI TFATCABMLQ MTPRSE ASL8 ---------------- ----------- 1 --- no

RANDSLS off

IPSG IPGWAPC GTTMODE CGGTMOD PCT no no FLCdPA,FLCgPA no off

Link set table is (2 of 1024) 1% full.

;

Measurements

New registers are added to the SYSTOT reports for the PCT feature:

• PCTDPCLKP—number of MSUs where PCT DPC Lookup was done successfully (the MSU’s DPCand/or CIC was modified when the PCT DPC Lookup was performed)

• PCTOPCLKP—number of MSUs where the PCT OPC Lookup was done successfully (the MSU’sOPC and/or CIC was modified when the PCT OPC Lookup was performed)

These measurements can be obtained using the Measurements Control Platform, OAM-based, orE5-OAM Integrated Measurements collection method.

Limitations

All Network Management may not work fully due to the overlap of CIC across multiple point codes.

Pre-LNP Query Service GTT processing

The Pre-LNP Query Service GTT processing feature allows Global Title Translation (GTT) to beperformed on messages before the messages are processed by the LNP local subsystem.

GTT is used to determine whether the originator of the query has an agreement with the LNP serviceprovider to perform LNP database lookup. If an agreement exists, then LNP service processing isperformed and an appropriate response is sent to the originator. If an agreement does not exist, thenthe query is routed as per the GTT result.

This functionality is available for LNP Query Services (AIN, IN, LRNQT, LNPQS, PCS, and WNP).




The EGTT feature must be turned on before the Pre-LNP Query Service GTT processing functionalitycan be provisioned.


The Pre-LNP Query Service GTT processing functionality requires an E5-SM4G or higher card.

Commands

The ent/chg/dlt/rtrv-lnp-serv commands are enhanced to provision and display the optionsallowing Pre-LNP Query Service GTT Processing.

An example of output for the rtrv-lnp-serv command is shown in the Commands section for theFall-back to GTT after LNP MR Service feature.

Limitations


Support CRP check for SRI_SM using TCAP digits

The Support CRP check for SRI_SM using TCAP digits feature allows SCCP or TCAP MSISDN digitsof SRI_SM messages to be used as the Directory or Dialed Number (DN) for MNP Circular RoutePrevention (MNPCRP) processing performed by the MT-Based GSM SMS NP feature.

If the TCAP MSISDN is used as the DN, a Home Routing Number (RN) match is found in the incomingTCAP MSISDN digits, and the SRI_SM message is to be relayed, then the RN digits from the TCAPMSISDN are stripped before relaying the message to the Home Location Register (HLR).


The MT-Based GSM SMS NP feature (Part Number 893-0200-01) must be enabled before the SupportCRP check for SRI_SM using TCAP digits functionality can be provisioned.


None.

Commands

The chg/rtrv-gsmsmsopts commands are enhanced to provision and display the Support CRPcheck for SRI_SM using TCAP digits functionality.

rtrv-gsmsmsopts

tekelecstp 10-09-23 11:27:38 EST EAGLE5 43.0.0 GSM SMS OPTIONS --------------------------------------



BPARTYGTTSN = NONE MOSMSGTTDIG = SCCPCDPA MOSMSTYPE = SPRN MOSMSNAI = INTL MOSMSSA = NO MOSMSFWD = NO MOSMSACLEN = 0 MOSMSGTA = NONE MOSMSTCAPSEG = OFF MOSMSDIGMAT = EXACT SPORTTYPE = NONE SPFILL = OFF DEFRN = NONE

MTSMSIMSI = MCCRNDN MTSMSNNI = RN MTSMSTYPE = RN MTSMSACKN = ACK MTSMSDLTR = NO MTSMSDLTRV = NONE MTSMSNAKERR = 1 MTSMSCHKSRC = NO MTMMSTYPE = RN SRISMDN = SCCP

MTMMSGTA = NONE MTMMSACKN = ACK MTMMSENTYLEN = NONE MTMMSLEN = NONE

IGMSMSRELAY = NO DEFIS41SMSC = NONE IS41SMSCGTTSN= NONE

Limitations


XUDT Conversion Enhancements

The XUDT Conversion Enhancements consists of two parts:

• A new XUDT UDT Conversion feature allows XUDT(S) < - > UDT(S) conversion to occur basedon the Destination Point Code (DPC) for MTP-routed and EAGLE-generated SCCP messages.Format conversions for both segmented and non-segmented messages are supported: however,the system does not perform segmentation or reassembly.

• The existing ANSI-ITU-China SCCP Conversion feature is enhanced to support XUDT(S) conversionfor MTP-routed and GT-routed SCCP messages. As part of this enhancement, the ANSI-ITU-ChinaSCCP Conversion feature is now referred to as the ANSI/ITU SCCP Conversion feature.

For GT-routed messages and MTP-Routed SCCP messages that are processed on Service Modulecards, XUDT UDT conversion is applied after the ANSI/ITU SCCP Conversion feature processes themessages.

The ANSI/ITU SCCP Conversion feature and the XUDT UDT Conversion feature can operateindependently of each other.


• The XUDT UDT Conversion feature requires a FAK for Part Number 893-0353-01.• The XUDT UDT Conversion feature cannot be turned off after it has been turned on.• A temporary FAK cannot be used to enable the XUDT UDT Conversion feature.• The ANSI/ITU SCCP Conversion feature requires a FAK for the existing Part Number 893-0120-01.




None.

Commands

• enable/chg/rtrv-ctrl-feat—Enhanced to enable, turn on, and display the status of theXUDT UDT Conversion feature.

rtrv-ctrl-feat


The following features have been permanently enabled: Feature Name Partnum Status Quantity HC-MIM SLK Capacity 893012707 on 64 Command Class Management 893005801 on ---- LNP Short Message Service 893006601 on ---- Prepaid SMS Intercept Ph1 893006701 on ---- Intermed GTT Load Sharing 893006901 on ---- MNP Circ Route Prevent 893007001 on ---- XGTT Table Expansion 893006101 on 400000 XMAP Table Expansion 893007710 on 3000 Large System # Links 893005911 on 2800 Routesets 893006403 on 8000 EAGLE5 Product 893007101 on ---- EAGLE Product 893007201 off ---- IP7 Product 893007301 off ---- Network Security Enhance 893009101 off ---- Telnet 893005701 on ---- 15 Minute Measurements 893012101 off ---- EIR 893012301 on ---- EAGLE OA&M IP Security 893400001 off ---- SCCP Conversion 893012001 on ---- SE-HSL SLK Capacity 893013005 on 32 GPORT 893017201 on ---- APORT 893016601 on ---- IS41 GSM Migration 893017301 off ---- INP 893017901 on ---- G-Flex 893021901 on ---- XUDT UDT Conversion 893035301 on ----

;

• ent/chg/dlt/rtrv-dstn—Enhanced to provision the type of conversion performed on MSUsthat are associated with a specified destination.

Example 1 displays the output for a destination point code.rtrv-dstn:dpc=200-200-*

eagle10115 10-058-12 10:00:37 EST EAGLE 43.0.0

DPCA CLLI BEI ELEI ALIASI ALIASN/N24 DMN 200-200-* cluster2 yes no -------------- -------------- SS7

SPCA NCAI RCAUSE NPRST SPLITIAM HMSMSC HMSCP SCCPMSGCNV ----------- yes none off none no no none

Destination table is (197 of 2000) 10% full Alias table is (206 of 12000) 2% full;



Example 2 displays the output when a proxy point code is referenced.rtrv-dstn:dpc=1-1-1

eagle10115 10-05-12 10:00:37 EST EAGLE 43.0.0

DPCA CLLI BEI ELEI ALIASI ALIASN/N24 DMN 001-001-001 ----------- no --- -------------- -------------- SS7

PPCA NCAI PRX RCAUSE NPRST SPLITIAM HMSMSC HMSCP SCCPMSGCNV 002-002-002 ---- no none off none no no none

Destination table is (30 of 2000) 2% full Alias table is (0 of 12000) 0% full PPC table is (1 of 100) 10% full;

Example 3 displays the output for all destinations having a specified SCCP Message ConversionIndicator.rtrv-dstn:sccpmsgcnv=udt2xudt

eagle10115 10-05-12 10:00:37 EST EAGLE 43.0.0

DPCA CLLI BEI ELEI ALIASI ALIASN/N24 DMN 001-001-001 ----------- no --- -------------- -------------- SS7 001-001-002 ----------- no --- -------------- -------------- SS7 001-001-003 ----------- no --- -------------- -------------- SS7 001-001-004 ----------- no --- -------------- -------------- SS7

Destination table is (17 of 2000) 1% full Alias table is (0 of 12000) 0% full PPC table is (0 of 10) 0% full

• ent-gtcnv—Enhanced to support XUDT(S) messages.

Measurements

The UDTXUDTF register is added to the SYSTOT-STP, MTCD-STP, and MTCDTH-STP reports. Thisregister counts the number of XUDT(S) <-> UDT(S) conversion failures.

These measurements can be obtained using the Measurements Control Platform, OAM-based, orE5-OAM Integrated Measurements collection method.

Limitations


Other Changes

The following core enhancements are introduced in Release 44.0:



Change the number of digits in the MAP Routing Info of the returned SRI_ACK messageto 15

The number of digits in the MAP Routing Info portion of the returned SRI_ACK message can beconfigured by the user. A new msrnlen parameter is added to the chg-gsmopts command to allowthe configuration.

See the Commands section for the G-Flex MLR Support for Additional Opcodes feature for an exampleof rtrv-gsmopts output.

E5-TDM does not support Hardware Flow Control

The E5-TDM card does not support hardware flow control on the serial MMI port. If a value of hw orboth is specified for the fc parameter in the chg-trm command for an E5-TDM card, then part of theterminal output may be lost.

In addition, ports set for hardware flow control only operate in KSR mode.

Extended Processing Time Notification

The rept-stat/rtrv-dstn and rept-stat/rtrv-rte commands are updated to display thewarning "Extended processing time may be required" before more than one destination or route statusis displayed.

Example 1 displays output for the rept-stat-dstn command.rept-stat-dstn

tekelecstp 10-10-15 14:59:15 EST EAGLE 43.0.0 rept-stat-dstn Command entered at terminal #4. Extended Processing Time may be Required

DPCA PST SST AST 001-001-003 OOS-MT Idle INACCESS 001-001-004 OOS-MT Idle INACCESS 001-001-005 OOS-MT Idle INACCESS 001-001-006 OOS-MT Idle INACCESS 001-001-007 OOS-MT Idle INACCESS 001-001-008 OOS-MT Idle INACCESS 001-001-009 OOS-MT Idle INACCESS 001-001-010 OOS-MT Idle INACCESS 001-001-011 OOS-MT Idle INACCESS 001-001-012 OOS-MT Idle INACCESS 001-001-013 OOS-MT Idle INACCESS 001-001-014 OOS-MT Idle INACCESS 001-001-015 OOS-MT Idle INACCESS 001-001-016 OOS-MT Idle INACCESS 001-001-017 OOS-MT Idle INACCESS 001-001-018 OOS-MT Idle INACCESS 001-001-019 OOS-MT Idle INACCESS 001-001-020 OOS-MT Idle INACCESS 001-001-021 OOS-MT Idle INACCESS 001-001-022 OOS-MT Idle INACCESS 001-001-023 OOS-MT Idle INACCESS 001-001-024 OOS-MT Idle INACCESS 001-001-025 OOS-MT Idle INACCESS 001-002-003 OOS-MT Idle INACCESS

DPCN PST SST AST



DPCN24 PST SST AST

DPCI PST SST AST

Command Completed.;

Example 2 displays output for the rept-stat-rte command.rept-stat-rte

tekelecstp 10-10-15 14:59:49 EST EAGLE 43.0.0 rept-stat-rte Command entered at terminal #4. Extended Processing Time may be Required

DPCA PST SST AST 001-001-003 OOS-MT Idle INACCESS 001-001-004 OOS-MT Idle INACCESS 001-001-005 OOS-MT Idle INACCESS 001-001-006 OOS-MT Idle INACCESS 001-001-007 OOS-MT Idle INACCESS 001-001-008 OOS-MT Idle INACCESS 001-001-009 OOS-MT Idle INACCESS 001-001-010 OOS-MT Idle INACCESS 001-001-011 OOS-MT Idle INACCESS 001-001-012 OOS-MT Idle INACCESS 001-001-013 OOS-MT Idle INACCESS 001-001-014 OOS-MT Idle INACCESS 001-001-015 OOS-MT Idle INACCESS 001-001-016 OOS-MT Idle INACCESS 001-001-017 OOS-MT Idle INACCESS 001-001-018 OOS-MT Idle INACCESS 001-001-019 OOS-MT Idle INACCESS 001-001-020 OOS-MT Idle INACCESS 001-001-021 OOS-MT Idle INACCESS 001-001-022 OOS-MT Idle INACCESS 001-001-023 OOS-MT Idle INACCESS 001-001-024 OOS-MT Idle INACCESS 001-001-025 OOS-MT Idle INACCESS 001-002-003 OOS-MT Idle INACCESS

DPCN PST SST AST

DPCN24 PST SST AST

DPCI PST SST AST

Command Completed.;

Example 3 displays truncated output for the rtrv-dstn command.rtrv-dstn

tekelecstp 10-10-15 14:46:12 EST EAGLE 43.0.0 rtrv-dstn Command entered at terminal #4. Extended Processing Time may be Required

DPCA CLLI BEI ELEI ALIASI ALIASN/N24 DMN 001-001-000 stp1 no --- -------------- -------------- SS7 003-001-000 mstp no --- -------------- -------------- SS7 004-001-000 stp4 no --- -------------- -------------- SS7

DESTINATION ENTRIES ALLOCATED: 2000



FULL DPC(s): 178 EXCEPTION DPC(s): 17 NETWORK DPC(s): 0 CLUSTER DPC(s): 4 TOTAL DPC(s): 199 CAPACITY (% FULL): 10% ALIASES ALLOCATED: 12000 ALIASES USED: 206 CAPACITY (% FULL): 2% X-LIST ENTRIES ALLOCATED: 500

;

Example 4 displays truncated output for the rtrv-rte command.rtrv-rte

tekelecstp 10-10-15 14:52:32 EST EAGLE 43.0.0 rtrv-rte Command entered at terminal #4. Extended Processing Time may be Required

DPCA ALIASI ALIASN/N24 RTX CLLI LSN RC APCA 001-001-000 -------------- -------------- No stp1 e2e1 10 001-001-000 003-001-000 -------------- -------------- No mstp e2e3 10 003-001-000 004-001-000 -------------- -------------- No stp4 e2e4 10 004-001-000 007-001-000 -------------- -------------- No stp7 e2e7 10 007-001-000 002-101-001 -------------- -------------- No ssp201 e2m1s1 10 002-101-001 e2e3 20 003-001-000 002-102-001 -------------- -------------- No ssp202 e2m1s2 10 002-102-001 e2e3 20 003-001-000 001-101-001 -------------- -------------- No ssp101 e2e1 10 001-001-000 e2e4 20 004-001-000 e2e3 30 003-001-000

;

PC_TYPE in Daily Maintenance and Hourly Maintenance Per SSP reports

The new field PC_TYPE is added to the Daily Maintenance (MTCD) and Hourly Maintenance (MTCH)Per SSP reports for enttype=aiq, atinpq, lnp, np, or vflex. The PC_TYPE field is defined as the PointCode type with four valid values: ANSI, ITUI, ITUN, ITUN24. The PC_TYPE field differentiates PointCodes which are numerically identical but are of different types. The output reports can be obtainedusing the Measurements Control Platform, OAM-based, or E5-OAM Integrated Measurements collectionmethod.

Examples of Daily Daily Maintenance Measurements Per SSP FTP Command:

rept-ftp-meas:type=mtcd:enttype=lnp

rept-ftp-meas:type=mtcd:enttype=np

Example of Daily LNP Measurements Per SSP report (MP and E5-OAM)

Example Output File Name:mtcd-ssp_20111006_2400.csv



Example Output File Format:"CLLI","SWREL","RPTDATE","RPTIME","TZ","RPTTYPE","RPTPD","IVALDATE","IVALSTART","IVALEND","NUMENTIDS"<cr><lf>"tekelecstp","34.0.0-39.1.0","2011-10-06","15:51:37","EST","DAILY MAINTENANCE MEASUREMENTS ON LNP SSP","LAST","2011-10-05","00:00:00","24:00:00",200<cr><lf><cr><lf>"STATUS","SSP","PC_TYPE","SSPQRCV","CLASSGTRQ","LIDBGTRQ","SSPQRCVP","SSPQRCVNP","CLASSGTRQP","CLASSGTRQNP","LIDBGTRQP","LIDBGTRQNP","CNAMGTRQP","CNAMGTRQNP","ISVMGTRQP","ISVMGTRQNP","WSMSCGTRQP","WSMSCGTRQNP"<cr><lf>"K","002-002-100","ANSI",123456789,456789,99999,123456789,456789,99999,123456789,456789,99999,123456789,456789,99999,123456789,456789,99999<cr><lf>....."K","002-005-123","ANSI",123456789,456789,99999,123456789,456789,99999,123456789,456789,99999,123456789,456789,99999,123456789,456789,99999<cr><lf>

Example of Daily NP Measurements Per SSP report (MP and E5-OAM)

Example Output File Name: mtcd-ssp_20110125_2400.csv

Example Output File Format:"CLLI","SWREL","RPTDATE","RPTIME","TZ","RPTTYPE","RPTPD","IVALDATE","IVALSTART","IVALEND","NUMENTIDS"<cr><lf>"e1061001","EAGLE5 43.0.0-63.33.0","2011-01-25","00:00:58","EST ","DAILY MAINTENANCE MEASUREMENTS ON NP SSP","LAST","2011-01-24","00:00:00","24:00:00",3<cr><lf><cr><lf>"STATUS","SSP","PC_TYPE","INPQSCONN","INPQSCONT","INPMRTR","INPMRGTT","GPSRACK","GPSRRLY","GPNOCL","GPNOCLGT","GPSRACKPP","APLRACK","APLRRLY","APNOCL","APNOCLGT","TINPMRCV","TINPMGEN","TINPERR","SMSMOIRCV","SMSMOIERR","SMSMOGRCV","SMSMOGERR","GPSRSMREP","GPSRSMERR","GPSRSMRCV","APSMRQREP","APSMRQERR","APSMSRCV","INPQSCRD","INPQSREL","INPMRCRD","MNPCRD","GPSRNACK"<cr><lf>"K","001-001-001","ANSI",0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0<cr><lf>"K","101-001-001","ANSI",0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0<cr><lf>"K","201-001-001","ANSI",0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0<cr><lf>

Support for the BLIXP GPL

A new BLIXP GPL is introduced. The BLIXP GPL is a flash GPL that contains a tar image with all ofthe previously independent flash GPLs required for E5-E1T1, E5-ENET, E5-SM4G, and HC-MIM cards.The BLIXP GPL is used to replace the BLBEPM, BLBIOS, BLBSMG, BLCPLD, BLDIAG6, BLROM1,BLVXW6, IMTPCI, and PLDPMC1 GPLs. The replaced GPLs are only available during upgrade to43.0 and during hardware replacement.

The act/init-flash, act/chg/rept-stat/rtrv-gpl, rept-meas, rept-stat/rtrv-card,and rtrv-stp commands are enhanced to support the BLIXP GPL.

Example 1 displays output for the rept-stat-card command.

rept-stat-card:loc=6101:mode=full

tklc9010801 10-12-09 17:25:55 MST EAGLE5 43.0.0 CARD VERSION TYPE GPL PST SST AST 6101 133-043-000 LIME1ATM ATMHC IS-NR Active ----- ALARM STATUS = No Alarms. BLIXP GPL version = 133-044-000 IMT BUS A = Conn IMT BUS B = Conn CLOCK A = Active CLOCK B = Idle CLOCK I = Idle HS CLOCK A = Fault HS CLOCK B = Fault HS CLOCK I = Idle MBD BIP STATUS = Valid MOTHER BOARD ID = EPM A DBD STATUS = Valid DBD TYPE = ATM DBD MEMORY SIZE = 512M



HW VERIFICATION CODE = ---- CURRENT TEMPERATURE = 37C ( 99F) PEAK TEMPERATURE: = 39C (103F) [02-01-01 21:00] SIGNALING LINK STATUS SLK PST LS CLLI A IS-NR sc8b095i sc8b095i B IS-NR sc5b092n sc5b092n TVG STATUS SNM TVG RESULT = 24 hr: G-----, 5 min: ------ SLAN TVG RESULT = 24 hr: ------, 5 min: ------ SCCP TVG RESULT = 24 hr: ------, 5 min: ------ INM TVG RESULT = 24 hr: G-----, 5 min: ------

Command Completed.;

Example 2 displays truncated output for the rept-stat-gpl command.

rept-stat-gpl:display=all

eagle10110 10-08-15 18:53:54 EST EAGLE 43.0.0 GPL Auditing ON

GPL CARD RUNNING APPROVED TRIAL GLS 1107 133-051-000 133-051-000 133-051-000 IMT 133-051-000 133-051-000 133-051-000 GLS 4308 133-051-000 133-051-000 133-051-000 IMT 133-051-000 133-051-000 133-051-000 OAMHC 1113 133-051-000 ALM 028-051-000 028-051-000 * BLMCAP 133-051-000 133-051-000 133-051-000 OAMHC 1115 028-051-000 028-051-000 028-051-000 * BLMCAP 133-051-000 133-051-000 133-051-000 VSCCP 3117 001-051-013 001-051-013 001-051-010 BPDCM 133-042-000 133-042-000 133-042-000 VSCCP 3201 001-051-013 001-051-013 001-051-010 BPDCM 133-042-000 133-042-000 133-042-000 IPGWI 2102 133-051-000 133-051-000 133-051-000 BPDCM 133-042-000 133-042-000 133-042-000 IPGWI 2115 133-051-000 133-051-000 133-051-000 BPDCM 133-042-000 133-042-000 133-042-000 IPS 5201 133-051-000 133-051-000 133-051-000 BPDCM 133-042-000 133-042-000 133-042-000 MCP 1108 133-051-000 133-051-000 133-051-000 BPDCM2 133-042-000 133-042-000 133-042-000 MCP 5313 133-051-000 133-051-000 133-051-000 BPDCM2 133-042-000 133-042-000 133-042-000 SS7HC 2201 133-051-000 133-051-000 133-051-000 BLIXP 133-050-000 133-050-000 027-051-000 SS7HC 3307 133-051-000 133-051-000 133-051-000 BLIXP 133-050-000 133-050-000 027-051-000 IPSG 3116 133-051-000 133-051-000 133-051-000 BLIXP 133-050-000 133-050-000 027-051-000 IPSG 4103 133-051-000 133-051-000 133-051-000 BLIXP 133-050-000 133-050-000 027-051-000 PKTGHC 1111 163-051-000 163-051-000 ----------- BLIXP 133-050-000 133-050-000 027-051-000

Command Completed.;

Example 3 displays truncated output for the rtrv-gpl command.

rtrv-gpl

e1080402 10-10-10 15:16:33 EST EAGLE 43.0.0



GPL CARD RELEASE APPROVED TRIAL REMOVE TRIAL EOAM 1114 128-003-000 128-003-000 128-003-000 128-003-000 EOAM 1116 128-003-000 128-003-000 ----------- ----------- SCCP 1114 128-002-000 128-002-000 128-002-000 128-002-000 SCCP 1116 128-002-000 128-002-000 128-002-000 ----------- GLS 1114 128-002-000 128-002-000 128-002-000 128-002-000 GLS 1116 128-002-000 128-002-000 128-002-000 ----------- CDU 1114 128-000-000 128-000-000 128-000-000 128-002-000 CDU 1116 128-000-000 128-000-000 128-002-000 ----------- STPLAN 1114 128-001-000 128-001-000 125-001-000 128-001-000 STPLAN 1116 128-001-000 128-001-000 125-001-000 ----------- IMT 1114 128-001-000 128-001-000 125-001-000 128-001-000 IMT 1116 128-001-000 128-001-000 125-001-000 ----------- ATMANSI 1114 128-002-000 128-002-000 125-002-000 128-002-000 ATMANSI 1116 128-002-000 128-002-000 128-002-000 ----------- HIPR 1114 128-001-000 128-005-000 125-005-000 128-005-000 HIPR 1116 128-001-000 128-005-000 125-005-000 ----------- SS7HC 1114 128-001-000 128-001-000 125-001-000 128-001-000 SS7HC 1116 128-001-000 128-001-000 125-001-000 ----------- IPLHC 1114 097-003-000 097-003-000 028-003-011 097-003-000 IPLHC 1116 097-003-000 097-003-000 028-003-011 ----------- IPGHC 1114 097-003-000 097-003-009 ALM 097-003-001 097-003-009 IPGHC 1116 097-003-000 097-003-009 ALM 097-003-001 ----------- IPSHC 1114 128-001-000 128-001-000 128-001-000 ----------- IPSHC 1116 128-001-000 128-001-000 128-001-000 128-001-000 SLANHC 1114 128-002-000 128-002-000 128-002-000 ----------- SLANHC 1116 128-002-000 128-002-000 128-002-000 128-002-000 ERTHC 1114 128-002-000 128-002-000 128-002-000 ----------- ERTHC 1116 128-002-000 128-002-000 128-002-000 128-002-000 SCCPHC 1114 128-019-000 128-019-000 128-019-000 ----------- SCCPHC 1116 128-019-000 128-019-000 128-019-000 128-019-000 HIPR2 1114 128-022-000 128-022-000 128-022-000 128-022-000 HIPR2 1116 128-022-000 128-022-000 128-022-000 ----------- BLIXP 1114 163-033-000 163-033-000 ----------- ----------- BLIXP 1116 163-033-000 163-033-000 ----------- -----------

;

Example 4 displays truncated output for the rtrv-gpl command when E5 cards are used.

rtrv-gpl

tklc9051301 10-08-17 10:13:26 EST EAGLE5 43.0.0 GPL Auditing ON

GPL CARD RELEASE APPROVED TRIAL REMOVE TRIAL EOAM 1114 133-033-000 133-033-000 ----------- ----------- EOAM 1116 133-033-000 133-033-000 ----------- ----------- EOAM 1115 ----------- ----------- ----------- ----------- GLS 1114 133-033-000 133-033-000 133-033-000 ----------- GLS 1116 133-033-000 133-033-000 133-033-000 ----------- GLS 1115 ----------- ----------- ----------- ----------- CDU 1114 163-033-000 163-033-000 ----------- ----------- CDU 1116 163-033-000 163-033-000 ----------- ----------- CDU 1115 ----------- ----------- ----------- ----------- IMT 1114 133-033-000 133-033-000 133-033-000 ----------- IMT 1116 133-033-000 133-033-000 133-033-000 ----------- IMT 1115 ----------- ----------- ----------- ----------- IPLIM 1114 133-033-000 133-033-000 133-033-000 ----------- IPLIM 1116 133-033-000 133-033-000 133-033-000 ----------- IPLIM 1115 ----------- ----------- ----------- ----------- IPLIMI 1114 133-033-000 133-033-000 133-033-000 ----------- IPLIMI 1116 133-033-000 133-033-000 133-033-000 ----------- IPLIMI 1115 ----------- ----------- ----------- ----------- MPLG 1114 163-033-000 163-033-000 163-033-000 -----------



MPLG 1116 163-033-000 163-033-000 163-033-000 ----------- MPLG 1115 ----------- ----------- ----------- ----------- HIPR 1114 133-033-000 133-033-000 133-033-000 ----------- HIPR 1116 133-033-000 133-033-000 133-033-000 ----------- HIPR 1115 ----------- ----------- ----------- ----------- SS7HC 1114 133-033-000 133-033-000 133-033-000 ----------- SS7HC 1116 133-033-000 133-033-000 133-033-000 ----------- SS7HC 1115 ----------- ----------- ----------- ----------- GLSHC 1114 133-033-000 133-033-000 133-033-000 ----------- GLSHC 1116 133-033-000 133-033-000 133-033-000 ----------- GLSHC 1115 ----------- ----------- ----------- ----------- PKTGEN 1114 163-033-000 163-033-000 ----------- ----------- PKTGEN 1116 163-033-000 163-033-000 ----------- ----------- PKTGEN 1115 ----------- ----------- ----------- ----------- SCCPHC 1114 133-033-000 133-033-000 133-033-000 ----------- SCCPHC 1116 133-033-000 133-033-000 133-033-000 ----------- SCCPHC 1115 ----------- ----------- ----------- ----------- PKTGHC 1114 163-033-000 163-033-000 ----------- ----------- PKTGHC 1116 163-033-000 163-033-000 ----------- ----------- PKTGHC 1115 ----------- ----------- ----------- ----------- BLIXP 1114 163-033-000 163-033-000 ----------- ----------- BLIXP 1116 163-033-000 163-033-000 ----------- ----------- BLIXP 1115 ----------- ----------- ----------- -----------

;

Update to the msucount Command

The msucount command is updated to remove all references to the -d and -s sname options.

Example 1 displays a help report for IPGWx cards.pass:loc=1105:cmd="msucount -h"


Usage: msucount [ [-l [link]] | [-b [link]] | [[-a aname]] [[-x rc] | [-k [rtkey] [-p pctype] [-t keytype] []] ] [-f] [-r] [-h [full]]

Options: -l display signaling link report -b display signaling link bytes report -a display association report

-x routing key report using routing context -k routing key report using MTP3 parameters rtkey :: ([dpc][:si][:opc | :ssn][:cics][:cice]) -p pctype :: (ANSI, ITUI, ITUN, ITUN24, ITUIS, ITUNS) -t routing key type keytype :: (<full>, partial, default) -d display dynamic routing key -f display full report -r resets the specified counts -h display command help (brief or full)

rlghncxa03w 10-08-17 16:02:05 EST EAGLE 43.0.0 MSUCOUNT command complete

;

Example 2 displays a full help report for IPGWx cards.



pass:loc=1105:cmd="msucount -h full"


Usage: msucount [ [-l [link]] | [-b [link]] | [[-a aname]] [[-x rc] | [-k [rtkey] [-p pctype] [-t keytype]] ] [-f] [-r] [-h [full]]

Options: -l display signaling link report -b display signaling link bytes report -a display association report -x routing key report using routing context -k routing key report using MTP3 parameters rtkey :: ([dpc][:si][:opc | :ssn][:cics][:cice]) -p pctype :: (ANSI, ITUI, ITUN, ITUN24, ITUIS, ITUNS) -t routing key type keytype :: (<full>, partial, default) -d display dynamic routing key -f display full report -r resets the specified counts -h display command help (brief or full)

-k option details:

Use the -p option along with -k to specify the SS7 network domain and point code format for the network. The SS7IPGW default pctype is ANSI. The IPGWI default pctype is ITUI.

Network PC Format Notes ------- --------- -------------------------------------- ANSI N-C-M ITUN N Non-Spare ITU National, no group code ITUN N-GC Non-Spare ITU National with group code ITUI Z-A-I Non-Spare ITU International ITUN24 N-C-M Non-Spare ITU National, 24-bits ITUNS N Spare ITU National, no group code ITUNS N-GC Spare ITU National with group code ITUIS Z-A-I Spare ITU International

Use the -t option along with -k to specify certain MTP3 and user part MSU fields as wildcards for the routing key.

SS7 Traffic Partition RTKEY Parameter Example --------------------------------- ---------------------------- Any User Part to DPC 1-1-1 -k 1-1-1 -t partial SCCP to DPC 1-1-1 -k 1-1-1:3 -t partial ISUP to DPC 1-1-1 -k 1-1-1:5 -t partial TUP to DPC 1-1-1 -k 1-1-1:4 -t partial QBICC to DPC 1-1-1 -k 1-1-1:13 -t partial SI [0-2,6-12,14,15] to DPC 1-1-1 -k 1-1-1:SI SCCP SSN 5 to DPC 1-1-1 -k 1-1-1:3:5 ISUP to DPC 1-1-1 from OPC 2-2-2 -k 1-1-1:5:2-2-2 -t partial TUP to DPC 1-1-1 from OPC 2-2-2 -k 1-1-1:4:2-2-2 -t partial QBICC to DPC 1-1-1 from OPC 2-2-2 -k 1-1-1:13:2-2-2 -t partial ISUP CIC 1 to 1-1-1 from 2-2-2 -k 1-1-1:5:2-2-2:1 TUP CIC 1 to 1-1-1 from 2-2-2 -k 1-1-1:4:2-2-2:1 QBICC CIC 1 to 1-1-1 from 2-2-2 -k 1-1-1:13:2-2-2:1 ISUP CIC 0-5 to 1-1-1 from 2-2-2 -k 1-1-1:5:2-2-2:0:5 TUP CIC 0-5 to 1-1-1 from 2-2-2 -k 1-1-1:4:2-2-2:0:5 QBICC CIC 0-5 to 1-1-1 from 2-2-2 -k 1-1-1:13:2-2-2:0:5 Default Routing Key -k -t default




Example 3 displays a help report for IPLIMx cards.pass:loc=1103:cmd="msucount -h"


Usage: msucount [ [-l [link]] | [-b [link]] ] | [ [-a aname] ] [-r] [-h]

Options: -l display signaling link report -b display signaling link bytes report -a display association report -r resets the specified counts -h display command help


;

Update to the netstat Command

The netstat -i command output on non-E5 cards is updated to increase readability.pass: loc=1105: cmd="netstat -i"

eagle20004 11-01-07 07:59:20 EST EAGLE 43.0.0 pass: loc=1105: cmd="netstat -i" Command entered at terminal #1.;

eagle20004 11-01-07 07:59:20 EST EAGLE 43.0.0 PASS: Command sent to card;

eagle20004 11-01-07 07:59:20 EST EAGLE 43.0.0 DPLend (unit number 0): Flags: (0x63) UP BROADCAST ARP RUNNING 10MB HDX DIX Type: ETHERNET_CSMACD Internet address: 172.20.48.25 Broadcast address: 172.20.51.255 Netmask 0xffff0000 Subnetmask 0xfffffc00 Ethernet address is 00:00:00:00:00:00 Metric is 0 Maximum Transfer Unit size is 485 1 packets received; 1 packets sent 0 multicast packets received 0 multicast packets sent 0 input errors; 0 output errors 0 collisions; 0 dropped seeq (unit number 1): Flags: (0x63) UP BROADCAST ARP RUNNING 10MB HDX DIX Type: ETHERNET_CSMACD Internet address: 192.168.55.112 Broadcast address: 192.168.55.255 Netmask 0xffffff00 Subnetmask 0xffffff00 Ethernet address is 00:00:17:04:00:62 Metric is 0 Maximum Transfer Unit size is 1500



28 packets received; 16 packets sent 13 multicast packets received 0 multicast packets sent 0 input errors; 0 output errors 0 collisions; 0 dropped lo (unit number 0): Flags: (0x8069) UP LOOPBACK MULTICAST ARP RUNNING 10MB HDX DIX Type: SOFTWARE_LOOPBACK Internet address: 127.0.0.1 Netmask 0xff000000 Subnetmask 0xff000000 Metric is 0 Maximum Transfer Unit size is 32768 6 packets received; 6 packets sent 0 multicast packets received 0 multicast packets sent 0 input errors; 0 output errors 0 collisions; 0 dropped seeq (unit number 0): Flags: (0x63) UP BROADCAST ARP RUNNING 10MB HDX DIX Type: ETHERNET_CSMACD Internet address: 192.168.100.112 Broadcast address: 192.168.100.255 Netmask 0xffffff00 Subnetmask 0xffffff00 Ethernet address is 00:00:17:04:00:61 Metric is 0 Maximum Transfer Unit size is 1500 5 packets received; 1 packets sent 5 multicast packets received 0 multicast packets sent 0 input errors; 0 output errors 0 collisions; 0 dropped

Update to rept-imt-lvl2 Command

The rept-imt-lvl2 command output is updated to provide greater readability. In addition, theAverage ack time field is replaced with the Retx Count field, which displays retransmitted MSUs.

Note: This example displays truncated output.

rept-imt-lvl2:sloc=1101:eloc=1115:loc=1101

rlghncxa03w 10-09-08 14:49:58 EST EAGLE5 43.0.0 Retrieving data from card... -------------------------------------------------------------------------- Card: H'00f0 Bus: A

Field f0 f1 f2 f3 f4 f5 f6 f7 ----- ---- ---- ---- ---- ---- ---- ---- ---- Link Status ALGN ALGN ALGN -OS- -OS- -OS- ALGN -OS- OS Count (dec) 2 7 4 0 0 0 16 0 Transmit BSN (dec) 0 148 1 0 0 0 0 0 Transmit FSN (dec) 0 139 151 0 0 0 0 0 Receive BSN (dec) 0 139 151 0 0 0 0 0 Receive FSN (dec) 1 149 2 1 1 1 1 1 Unack Messages (dec) 0 0 0 0 0 0 0 0 Invalid Length (dec) 0 0 0 0 0 0 0 0 Invalid rx BSN (dec) 0 0 0 0 0 0 0 0 Invalid rx FSN (dec) 0 0 0 0 0 0 0 0 Invalid LSSU (dec) 0 0 0 0 0 0 0 0 Invalid ASU (dec) 0 0 0 0 0 0 0 0 RTB Address (hex) 0000 0000 0000 0000 0000 0000 0000 0000 Retx Count (dec) 0 0 0 0 0 0 0 0 Minimum ack time (ms) 0 0 0 0 0 0 0 0 Maximum ack time (ms) 0 0 0 0 0 0 0 0



;

rlghncxa03w 10-09-08 14:49:59 EST EAGLE5 43.0.0 -------------------------------------------------------------------------- Card: H'00f0 Bus: A

Field f8 f9 fa fb ----- ---- ---- ---- ---- Link Status ALGN -OS- ALGN ALGN OS Count (dec) 16 0 1 2 Transmit BSN (dec) 0 0 158 168 Transmit FSN (dec) 1 0 9 106 Receive BSN (dec) 1 0 9 106 Receive FSN (dec) 1 1 159 169 Unack Messages (dec) 0 0 0 0 Invalid Length (dec) 0 0 0 0 Invalid rx BSN (dec) 0 0 0 0 Invalid rx FSN (dec) 0 0 0 0 Invalid LSSU (dec) 0 0 0 0 Invalid ASU (dec) 0 0 0 0 RTB Address (hex) 0000 0000 0000 0000 Retx Count (dec) 0 0 0 0 Minimum ack time (ms) 0 0 0 0 Maximum ack time (ms) 0 0 0 0;


Field 00 01 02 03 04 05 06 07 ----- ---- ---- ---- ---- ---- ---- ---- ---- Link Status ALGN -OS- -OS- -OS- ALGN ALGN ALGN -OS- OS Count (dec) 11 0 0 0 4 4 4 0 Transmit BSN (dec) 0 0 0 0 0 0 0 0 Transmit FSN (dec) 1 0 0 0 1 1 1 0 Receive BSN (dec) 1 0 0 0 1 1 1 0 Receive FSN (dec) 1 1 1 1 1 1 1 1 Unack Messages (dec) 0 0 0 0 0 0 0 0 Invalid Length (dec) 0 0 0 0 0 0 0 0 Invalid rx BSN (dec) 0 0 0 0 0 0 0 0 Invalid rx FSN (dec) 0 0 0 0 0 0 0 0 Invalid LSSU (dec) 0 0 0 0 0 0 0 0 Invalid ASU (dec) 0 0 0 0 0 0 0 0 RTB Address (hex) 0000 0000 0000 0000 0000 0000 0000 0000 Retx Count (dec) 0 0 0 0 0 0 0 0 Minimum ack time (ms) 0 0 0 0 0 0 0 0 Maximum ack time (ms) 0 0 0 0 0 0 0 0;


Field 08 09 0a 0b 0c 0d 0e 0f ----- ---- ---- ---- ---- ---- ---- ---- ---- Link Status -OS- -OS- ALGN ALGN ALGN ALGN -OS- -OS- OS Count (dec) 0 0 4 4 1 1 0 0 Transmit BSN (dec) 0 0 0 0 0 0 0 0 Transmit FSN (dec) 0 0 0 0 0 0 0 0 Receive BSN (dec) 0 0 0 0 0 0 0 0 Receive FSN (dec) 1 1 1 1 1 1 1 1 Unack Messages (dec) 0 0 0 0 0 0 0 0 Invalid Length (dec) 0 0 0 0 0 0 0 0 Invalid rx BSN (dec) 0 0 0 0 0 0 0 0



Invalid rx FSN (dec) 0 0 0 0 0 0 0 0 Invalid LSSU (dec) 0 0 0 0 0 0 0 0 Invalid ASU (dec) 0 0 0 0 0 0 0 0 RTB Address (hex) 0000 0000 0000 0000 0000 0000 0000 0000 Retx Count (dec) 0 0 0 0 0 0 0 0 Minimum ack time (ms) 0 0 0 0 0 0 0 0 Maximum ack time (ms) 0 0 0 0 0 0 0 0


Field 28 ----- ---- Link Status -OS- OS Count (dec) 0 Transmit BSN (dec) 0 Transmit FSN (dec) 0 Receive BSN (dec) 0 Receive FSN (dec) 1 Unack Messages (dec) 0 Invalid Length (dec) 0 Invalid rx BSN (dec) 0 Invalid rx FSN (dec) 0 Invalid LSSU (dec) 0 Invalid ASU (dec) 0 RTB Address (hex) 0000 Retx Count (dec) 0 Minimum ack time (ms) 0 Maximum ack time (ms) 0

;

Update to the rept-stat-imt Command

The rept-stat-imt command is updated to display IMT System Alarms.

Example 1 displays output for an abbreviated report.rept-stat-imt


IMT SYSTEM ALARM STATUS = No Alarms.

IMT PST SST AST A IS-NR Active ----- ALARM STATUS = No Alarms.

IMT PST SST AST B IS-NR Active ----- ALARM STATUS = No Alarms.

Command Completed.;

Example 2 displays output for a full report.rept-stat-imt:mode=full


IMT SYSTEM



ALARM STATUS = * 0110 Failure detected on one IMT bus

IMT PST SST AST A IS-NR Active ----- ALARM STATUS = No Alarms.

IMT PST SST AST B OOS-MT-DSBLD Fault ----- ALARM STATUS = ** 0108 Major IMT failure detected.

CARDS WITH ACTIVE IMT B ALARMS: CARD DATE TIME 1102 04-02-23 11:59:23 1103 04-02-23 12:01:23 1204 04-02-23 23:14:07 1205 04-02-23 23:14:07 1206 04-02-23 23:14:07

Command Completed.;

Update to the rept-stat-rtkey Command

The rept-stat-rtkey command output is updated to provide greater readability.rept-stat-rtkey

rlghncxa03w 10-10-27 14:59:11 EST EAGLE 43.0.0 SRKQ = 250

Static Route Key table is (50 of 250) 20% full

Static Route Key Socket Association table is (80 of 4000) 2% full

;

Operational Changes

Release 44.0 contains new and updated alarms and error messages for feature and non-feature items.

UIMs

Hybrid INP/IDPR Relay Service

Table 2: UIM: Hybrid INP/IDPR Relay Service

Output GroupFormat1382UIM

Updated for 43.0Action

LSS: Too many digitsfor DRA parameter

Old data

APSSI13Too many digits forDRA parameter

New data



G-Flex MLR Support for Additional Opcodes

Table 3: UIM: G-Flex MLR Support for Additional Opcodes


Added for 43.0Action

Old data

APSSI13G-Flex MLR: Op w/oIMSI/MSISDN skipped

New data

Multiple IDPR Instances

Table 4: UIM: Multiple IDPR Instances



GTTI1IDPRCDPN NPPSERVICE is Disabled

Old data

GTTI1IDPRCDPN(X) NPPSERVICE is OFF

New data



GTTI1IDPRCGPN NPPService is Disabled

Old data

GTTI1IDPRCGPN NPPSERVICE is OFF

New data

XUDT Conversion Enhancements

Table 5: UIMs: XUDT Conversion Enhancements



Old data

GTTI43XUDT UDT Conversionfailed

New data



Old data



GTTI43Cnvrsn Discard: invsegmentation parm

New data

Non-feature UIM

Table 6: UIM: Non-Feature



Old data

GWSI21Binding Failed forscreen set: <screen setname>

New data

The formats of the following UIMs were updated from I1 to I13:

• 1384: G-Flex MLR: Op without IMSI erroneous• 1385: G-Flex MLR: Op without IMSI skipped• 1386: G-Flex MLR: Op with bad TCAP skipped• 1387: G-Flex MLR: Op with bad IMSI skipped

Hardware Verification Code

Table 7: Hardware Verification Code: 3 ATM Links per E5-ATM Card

UAMNew?DescriptionCard TypeHardwareVerification Code

297YSingle Port ATMcard with incorrectlink configured

LIMATM,LIME1-ATM

136

Error Messages

3 Links per E5-ATM Card

Table 8: Error Messages: 3 Links per E5-ATM Card

Used by CommandNew?Error MessageResponse ID Code

ent-slkNCard must be inhibitedbefore executing thiscommand

E2603

ent-slkYVCI value greater than16383 not allowed

E5437




ent-slkY3 Links per E5-ATMcard feature must beenabled

E5438

enable-ctrl-featYATM link with VCIgreater than 16383 exists

E5439

ent-slkYNumber of ATM cardswith 3 links exceedsallowable quantity

E5462

Error Message: 10,000 Routesets

Table 9: Error Message: 10,000 Routesets


chg-dbNBoth OAM cards must

be of the same typeE3084

copy-disk

enable-ctrl-featNUnsupported Hardwareis equipped in thesystem

E4581

Error Messages: Fall-back to GTT after LNP MR service

Table 10: Error Messages: Fall-back to GTT after LNP MR service


chg-lnp-servNService Type is alreadyin LNP database

E3140

ent-lnp-servNTT, TTN, & DVparameters are notallowed with ALIAS

E3186

ent/chg-lnp-servNEGTT must be ONE3557

ent/chg-lnp-servNSame option in ON &OFF params cannot bespecified

E4732

ent/chg/dlt/rtrv-lnp-servNUnable to access GTTAction table

E5067

ent/chg-lnp-servNGTT Action Id does notexist

E5071

ent/chg-lnp-servNInvalid action typeE5172




ent/chg-lnp-servNDefault ACTID mustnot be specified asNONE

E5298

Error Messages: G-Flex MLR Support

Table 11: Error Messages: G-Flex MLR Support


chg-gsmoptsYSame option can't bespec in

E5429

MAPLYRRTGON andMAPLYRRTGOFF

chg-gsmoptsYIf MAPLYRRTGON/MAPLYRRTGOFF is

E5430

ALL no option can bespec

chg-gsmoptsYIf MAPLYRRTGON isALL, MAPLYRRTGOFFcannot be specified

E5431

chg-gsmoptsYIf MAPLYRRTGOFF isALL, MAPLYRRTGONcannot be specified

E5432

Error Message: Hybrid INP/IDP Relay Service

Table 12: Error Message: Hybrid INP/IDP Relay Service


chg-measoptsNSame option in ON &

OFF params cannot bespecified

E4732

chg-ttropts

Error Message: Multiple IDP Relay Instances

Table 13: Error Message: Multiple IDP Relay Instances


chg-ctrl-featNAt least 1IDPRCDPN(X) srvc

E4861

must be ON to turn ONIDPR FEAT



Error Messages: PCT

Table 14: Error Messages: PCT


ent/dlt/rtrv-pctNInvalid parametercombination specified

E2155

ent/dlt/rtrv-pctNPoint code matches aSTP capability pointcode

E2167

ent/dlt/rtrv-pctNPoint code matches aSTP point code

E2168

ent/dlt/rtrv-pctNPoint code out of rangeE2169

ent/dlt/rtrv-pctNMissing parameterE2379

ent/dlt/rtrv-pctNPoint code does notexist in the routing table

E2417

ent/dlt/rtrv-pctNDPC must have at leastone route defined

E2642

ent-pctNFailed reading the routetable

E2648

ent/dlt/rtrv-pctNFull Point Code must bespecified

E3090

ent/dlt/rtrv-pctNCIC outside of validrange for SI

E3878

ent/dlt/rtrv-pctNPoint code matches aSTP secondary pointcode.

E4238

ent/dlt/rtrv-pctNEnd value must begreater than or equal toa starting value

E4404

ent/dlt/rtrv-pctNCIC must be specified ifECIC is specified

E4580

ent/dlt/rtrv-pctNPoint code typemismatch

E4606

ent-pctYPCT table is fullE5390

chg-lsoptsYPCT feature must be

enabledE5391

chg-stpopts

ent/dlt-pct

rtrv-ls




ent/dlt/rtrv-pctYThe PCT table is corruptor cannot be found

E5392

ent-pctYDuplicate keys are notallowed

E5393

ent/dlt/rtrv-pctYGroup Code of EPC,RealPC and FiltPC mustmatch

E5394

enable-ctrl-featYMaximum PCTQuantity FAK alreadyenabled

E5395

enable-ctrl-featYLarger PCT QuantityFAK is required

E5396

dlt-rteYCannot delete last routeto DPC referenced inPCT table

E5397

ent-pctYMax no of uniqueEPCs/RealPCs cannotexceed 250

E5398

ent-pctYMax no of PCTTranslations per

E5399

EPC/RealPC cannotexceed 100

ent/dlt/rtrv-pctYSpare point code is notallowed

E5400

ent/dlt/rtrv-pctYSingle translation entrynot found

E5401

ent/dlt/rtrv-pctYPrivate point code is notallowed

E5402

ent/dlt/rtrv-pctYInvalid SI valuespecified

E5424

ent/dlt/rtrv-pctYECICS/ECICE andRCICS/RCICE shouldbe in same range

E5426

ent/dlt/rtrv-pctYECIC/Real CIC rangecan't be same if EPC issame as Real PC

E5433

ent/dlt/rtrv-pctYOnly one of FILTPC/A,FILTPCI, or FILTPCNmay be specified

E5440




chg-sidYPoint Code matches an

Emulated Point Code inPCT table

E5466

ent-spc

Error Message: XUDT UDT Conversion

Table 15: Error Message: XUDT UDT Conversion


ent/chg/rtrv-dstnYXUDT UDT Conversionfeature must beactivated

E5384

Non Feature-Related Error Messages

Table 16: Non Feature-Related Error Messages


rtrv-srvselNEGTT must be ONE3557

chg-measNCOLLECT can't be ONif COLLECT15MIN &

E3693

PLATFORMENABLEare ON

ent-appl-rtkeyNInvalid combination ofparameters for a defaultrouting key

E4067

dlt-dstnYCannot delete DSTNthat has ExceptionRoute

E5434

tst-imtNTarget bus must beIS-NR or IS-ANR

E5188

Customer Care Center

The Tekelec Customer Care Center is your initial point of contact for all product support needs. Arepresentative takes your call or email, creates a Customer Service Request (CSR) and directs yourrequests to the Tekelec Technical Assistance Center (TAC). Each CSR includes an individual trackingnumber. Together with TAC Engineers, the representative will help you resolve your request.

The Customer Care Center is available 24 hours a day, 7 days a week, 365 days a year, and is linkedto TAC Engineers around the globe.



Tekelec TAC Engineers are available to provide solutions to your technical questions and issues 7days a week, 24 hours a day. After a CSR is issued, the TAC Engineer determines the classification ofthe trouble. If a critical problem exists, emergency procedures are initiated. If the problem is not critical,normal support procedures apply. A primary Technical Engineer is assigned to work on the CSR andprovide a solution to the problem. The CSR is closed when the problem is resolved.

Tekelec Technical Assistance Centers are located around the globe in the following locations:

Tekelec - Global

Email (All Regions): [email protected]

• USA and Canada

Phone:

1-888-FOR-TKLC or 1-888-367-8552 (toll-free, within continental USA and Canada)

1-919-460-2150 (outside continental USA and Canada)

TAC Regional Support Office Hours:

8:00 a.m. through 5:00 p.m. (GMT minus 5 hours), Monday through Friday, excluding holidays• Caribbean and Latin America (CALA)

Phone:

USA access code +1-800-658-5454, then 1-888-FOR-TKLC or 1-888-367-8552 (toll-free)

TAC Regional Support Office Hours (except Brazil):

10:00 a.m. through 7:00 p.m. (GMT minus 6 hours), Monday through Friday, excluding holidays

• Argentina

Phone:

0-800-555-5246 (toll-free)• Brazil

Phone:

0-800-891-4341 (toll-free)


8:00 a.m. through 5:48 p.m. (GMT minus 3 hours), Monday through Friday, excluding holidays• Chile

Phone:

1230-020-555-5468• Colombia

Phone:

01-800-912-0537• Dominican Republic

Phone:

1-888-367-8552



• Mexico

Phone:

001-888-367-8552• Peru

Phone:

0800-53-087• Puerto Rico

Phone:

1-888-367-8552 (1-888-FOR-TKLC)• Venezuela

Phone:

0800-176-6497

• Europe, Middle East, and Africa

Regional Office Hours:

8:30 a.m. through 5:00 p.m. (GMT), Monday through Friday, excluding holidays

• Signaling

Phone:

+44 1784 467 804 (within UK)• Software Solutions

Phone:

+33 3 89 33 54 00

• Asia

• India

Phone:

+91 124 436 8552 or +91 124 436 8553


10:00 a.m. through 7:00 p.m. (GMT plus 5 1/2 hours), Monday through Saturday, excludingholidays

• Singapore

Phone:

+65 6796 2288


9:00 a.m. through 6:00 p.m. (GMT plus 8 hours), Monday through Friday, excluding holidays



Related Publications

For information about additional publications that are related to this document, refer to the RelatedPublications document. The Related Publications document is published as a part of the ReleaseDocumentation and is also published as a separate document on the Tekelec Customer Support Site.

Customer Training

Tekelec offers a variety of technical training courses designed to provide the knowledge and experiencerequired to properly provision, administer, operate, and maintain Tekelec products. To enroll in anyof the courses or for schedule information, contact the Tekelec Training Center at (919) 460-3064 orE-mail [email protected].

A complete list and schedule of open enrollment can be found at www.tekelec.com.

Locate Product Documentation on the Customer Support Site

Access to Tekelec's Customer Support site is restricted to current Tekelec customers only. This sectiondescribes how to log into the Tekelec Customer Support site and locate a document. Viewing thedocument requires Adobe Acrobat Reader, which can be downloaded at www.adobe.com.

1. Log into the Tekelec Customer Support site.

Note: If you have not registered for this new site, click the Register Here link. Have your customernumber available. The response time for registration requests is 24 to 48 hours.

2. Click the Product Support tab.3. Use the Search field to locate a document by its part number, release number, document name, or

document type. The Search field accepts both full and partial entries.4. Click a subject folder to browse through a list of related files.5. To download a file to your location, right-click the file name and select Save Target As.

EAGLE 5 ISS Card Overview Table

The EAGLE 5 ISS Card Overview table is a resource table that provides an overview of informationfor cards that can be provisioned in the EAGLE 5 ISS. For a detailed description of supported hardware,see Hardware Baseline.

This table lists the following card information:

• The name of the card on the card label• The card part number• The provisioned card type



https://secure.tekelec.com/OA_HTML/ibuhpage.jsp

• The number of shelf slots that the card occupies (1 or 2)• The number of physical ports on the card• The maximum number of links that can be assigned to the card• The GPLs and applications that can run on the card

Table 17: EAGLE 5 ISS Card Overview Table

Card

Applications

Card

GPLs

Linksper

Card

Per Card

Slots/Ports

ProvisionedCard Type

Part NumberCard Name asshown on card

label

stplanbpdcm

vwxslan1 IPService2

2dcm870-1945-01

870-1945-02

870-1945-03DCM

iplimbpdcm

22

870-1984-01(DCMX)

iplimiiplim

iplimi

ss7ipgwbpdcm

12ipgwi

ss7ipgw

ipgwi

eroutebpdcm

eroute2 IPService22stc

stplanbpdcm

vwxslan1 IPService

21dcm

870-2372-01

870-2372-08

870-2372-13ÊDCM

(SSEDCM)

iplimbpdcm

8iplimi

iplim

iplimi

ss7ipgwbpdcm

1ipgwi

ss7ipgw

ipgwi

eroutebpdcm

eroute2 IPService21stc870-2372-01



Card

Applications

Card

GPLs

Linksper

Card

Per Card

Slots/Ports



label

stplanbpdcm

vwxslan1 IPService21dcm

870-2508-01

870-2508-02^

EDCM-A

(SSEDCM)eroute

bpdcm

eroute2 IPService21stc

vsccp

bpdcm

vsccp2 IPservice22dsm

1 GB MEM

870-1984-02

DSM†

gls

870-1984-08

870-1984-09

870-1984-15^

870-1984-17^

2 GB MEM

870-1984-03

4 GB MEM870-1984-05

870-1984-06

870-1984-07

870-1984-13^

870-1984-16^

ipsbpdcm

ips1 IPservice

2 (useonlyA)

1ipsm

870-2371-02

870-2371-06

870-2371-08DSM-1G

870-2371-13^

mcp

bpdcm

bpdcm21 IPservice

2 (useonlyA)

1mcpm

870-2372-03

870-2372-07

870-2372-09EDSM-2G*

mcp870-2372-14^

870-2372-15^



Card

Applications

Card

GPLs

Linksper

Card

Per Card

Slots/Ports



label

ss7ansiss7ml821

lime1

limt1

870-2198-01

870-2198-02

E1/T1 MIM††ccs7itubpmplt

limch

870-2198-03

870-2198-04

870-2198-07^

atmitu

atmitu

bphcap121lime1atm

870-2455-01

870-2455-02E1-ATM

bphcapt870-2455-03

870-2455-05^

atmansiatmhc34 (3used)

1limatm

lime1atm

870-1872-01^

870-1872-02^

E5-ATM

atmitublixp

ss7ansi

ss7hc

3281lime1

limt1870-1873-02

870-1873-03^

870-1873-04^

E5-E1T1

ccs7itu

blixp ccs7itu181lime1 (forSE-HSL)

ss7ansi181limt1 (forST-HSL-A)

iplimiplhc1621

dcm870-2212-02

870-2212-03Ê5-ENET

iplimiblixp

870-2212-04^

ss7ipgwipghc121

870-2212-05^

ipgwiblixp

stplanslanhc2 IPService

21

blixp

erouteerthc2 IPService

21stc

blixp

ipsgipsg3221enet



Card

Applications

Card

GPLs

Linksper

Card

Per Card

Slots/Ports



label

blixp

ipsipshc1 ipshcservice

2 (useonlyA)

1

ipsm870-2877-01^

870-2877-02^

E5-IPSM

blixp

oamoamhcN/A22N/A870-2903-01Ê5-MASP

blmcap870-2903-02^

870-2903-03^

N/AN/AN/AN/A2N/A870-2900-01Ê5-MDAL

vsccpsccphc2 IPService

22dsm870-2860-01^

870-2860-02^

E5-SM4G

blixp

glsglshcN/A11tsm870-2943-03Ê5-TSM

blixp

oam

eoam

bpdcmN/AN/A1N/A

870-2360-01

870-2360-05

GPSM-II

bpdcm2

870-2360-06

870-2360-08^

870-2360-09^

ss7ansi

ss7hc6482

lime1

limt1870-2671-01

870-2671-02

870-2671-03^

HC-MIM††ccs7itu

blixpccs7itu282lime1 (for

SE-HSL)

hiprhiprN/AN/A1N/A870-2574-01

870-2574-02^HIPR

hipr2hipr2N/AN/A1N/A870-2872-01^HIPR2

870-2872-02^



Card

Applications

Card

GPLs

Linksper

Card

Per Card

Slots/Ports



label

bphmuxbphmuxN/AN/A1N/A870-1965-01

870-1965-03^HMUX

atmansi

atmansi

bphcap121limatm

870-1293-02

870-1293-03

LIM-ATM

bphcapt

870-1293-06

870-1293-07

870-1293-08

870-1293-10

870-1293-13^

N/AN/AN/AN/A2N/A

870-0773-04

870-0773-05

MDAL870-0773-06

870-0773-08

870-0773-09^

870-0773-10^

ss7ansibpmpl

ss7ml821limds0

870-2061-01

870-2061-03

870-2061-04MPL

870-2061-06^

N/AN/AN/AN/A1N/A870-0774-10

870-0774-11TDM

N/AN/AN/AN/A1N/A870-0774-15TDM-GTI

870-0774-18^

glsgls

imtN/AN/A1tsm

870-1289-02

870-1289-03

870-1289-04TSM-256

870-1289-06^



Card

Applications

Card

GPLs

Linksper

Card

Per Card

Slots/Ports



label

870-1289-07^

glsgls

imtN/AN/A1tsm

870-1290-02

870-1290-03

870-1290-04

TSM-512

glsgls

imtN/AN/A1tsm

870-1291-02

870-1291-03

870-1291-04

TSM-768

glsgls

imtN/AN/A1tsm

870-1292-02

870-1292-03

870-1292-04

TSM-1024

*Although the system allows 250 MCPM cards, practical usage is 2.

†DSM or E5-SM4G cards are required for the LNP, 50,000 GTT, or EPAP-related features. For moreinformation about turning these features on, refer to the appropriate manual.

††For the E1 or T1 interface, an SS7 application (SS7ANSI or CCS7ITU) can be assigned to these cards.

For more information on the E1 or T1 interface go to Chapter 3 “System Administration Procedures”in the Database Administration Manual - SS7.

^This part number is the ROHS equivalent of the immediately preceding part number.

Hardware Baseline

The Hardware Baseline is shown in the following table.

Table 18: Hardware Baseline

Required forROHS Number (ifapplicable)

Part NumberComponent

HMUX870-2321-08 Rev A870-2321-02 Rev AControl Shelf

HMUX, Standard Frame870-2321-04 Rev A

HMUX, Heavy DutyFrame

870-2377-02 Rev A870-2377-01 Rev A





870-0775-03 Rev EControl Shelf Backplane

Heavy Duty Frame870-2378-02 Rev A870-2378-01 Rev AExtension Shelf

Standard Frame870-0776-02 Rev C

870-0776-03 Rev D

870-0776-06 Rev A

870-0776-07 Rev A

870-0776-08 Rev A or

870-0776-11 Rev A

Shelves with FanAssembly

870-1824-02 Rev A870-1824-01 Rev AAir Management Card

870-1945-01 Rev A orDCM

870-1945-02 Rev A or

870-1945-03 Rev A

870-1984-01 Rev ADCMX

870-2372-01 Rev E orEDCM (single slot)

870-2372-13 Rev A870-2372-08 Rev A

870-2508-02 Rev A870-2508-01 Rev AEDCM-A (single slot)

870-1984-02 Rev A orDSM, 1GB MEM

870-1984-08 Rev A or

870-1984-15 Rev A870-1984-09 Rev A

870-1984-17 Rev A

870-1984-03 Rev ADSM, 2GB MEM

Heavy Duty Frame870-1984-05 Rev ADSM, 4GB MEM

870-1984-06 Rev A or

870-1984-13 Rev A870-1984-07 Rev A

870-1984-16 Rev A

870-2371-02 Rev ADSM-1G

870-2371-06 Rev A

870-2371-13 Rev A870-2371-08 Rev A or

870-2372-03 Rev AEDSM-2G (MCPM)





870-2372-07 Rev A

870-2372-14 Rev A870-2372-09 Rev A or

870-2372-15 Rev A

870-2198-01 Rev G orE1/T1 MIM

870-2198-02 Rev A or

870-2198-03 Rev A or

870-2198-07 Rev A870-2198-04 Rev A

870-2455-01 Rev BE1-ATM

870-2455-02 Rev B

87-02455-05 Rev A870-2455-03 Rev A

870-1872-01 Rev AE5-ATM

870-1872-02 Rev A

830-1342-05E5-ATM Adapter

870-1873-03 Rev A870-1873-02 Rev AE5-E1T1

870-1873-04 Rev A

870-2212-03 Rev A870-2212-02 Rev AE5-ENET

870-2212-04 Rev A

870-2212-05 Rev A

870-2877-01 Rev AE5-IPSM

870-2877-02 Rev A

870-2903-01 Rev CE5-MASP

870-2903-02 Rev A

870-2903-03 Rev A

870-2900-01 Rev AE5-MDAL

870-2860-01 Rev FE5-SM4G

870-2860-02 Rev A

870-2943-03 Rev AE5-TSM

Standard frame orstandard frame withHC-MIMs

870-1606-01 Rev A orFAP

870-1606-05 Rev A870-1606-02 Rev A





Heavy duty frame orheavy duty frame withHC-MIMs

870-2320-03 Rev A870-2320-01 Rev A

870-2804-01 Rev B870-1823-01 Rev B

870-0243-08 Rev CFAP-CF/EF

870-0243-09 Rev CFAP-MISC

870-2804-01 Rev AFAP Fuse and AlarmPanel

830-1343-01 Rev AFast Copy AdapterUpper

830-1343-02 Rev AFast Copy AdapterLower

870-2360-01 Rev EGPSM-II

870-2360-05 Rev A

870-2360-08 Rev A870-2360-06 Rev A

870-2360-09 Rev A

870-2671-01 Rev P orHC-MIM

870-2671-03 Rev A870-2671-02 Rev B

870-2574-02 Rev A870-2574-01 Rev DHIPR

870-2872-01 Rev AHIPR2

870-2872-02 Rev A

830-1344-xxHigh-speed FiberChannel Cable

870-1965-03 Rev A870-1965-01 Rev AHMUX

870-1293-02 Rev A orLIM-ATM

870-1293-03 Rev A or

870-1293-06 Rev A or

870-1293-07 Rev A or

870-1293-08 Rev B or

870-1293-13 Rev A870-1293-10 Rev A or

870-0773-04 Rev B orMDAL

870-0773-05 Rev A or

870-0773-06 Rev A or





870-0773-09 Rev A870-0773-08 Rev A

870-0773-10 Rev A

870-2061-01 Rev A orMPL

870-2061-03 Rev A or

870-2061-06 Rev A870-2061-04 Rev A

890-1843-02 Rev A890-1843-01 Rev CMPS DC FrameAssembly

890-1801-02 Rev A890-1801-01 Rev EMPS in Heavy DutyFrame

870-0774-10 Rev A orTDM

Rev C required ifinstalled in a system870-0774-11 Rev A

with more than 11shelves

870-0774-18 Rev A870-0774-15 Rev BTDM GTI

870-1289-02 Rev A orTSM-256

870-1289-03 Rev A or

870-1289-06 Rev A870-1289-04 Rev A

870-1289-07 Rev A

870-1290-02 Rev A orTSM-512

870-1290-03 Rev A or

870-1290-04 Rev A

870-1291-02 Rev A orTSM-768

870-1291-03 Rev A or

870-1291-04 Rev A

870-1292-02 Rev A orTSM-1024

870-1292-03 Rev A or

870-1292-04 Rev A

890-1037-06 Rev A890-1037-01 Rev AKit E1

890-1013-01 Rev AKit, Holdover ClockAssy

890-1038-01 Rev DFan Assy (StandardFrame)





890-0001-01 Rev A orFan Assy (Shelves withHC-MIM cards)

890-0001-04 Rev A890-0001-02 Rev A

870-2640-03 Rev A870-2640-01 Rev FT1000 ApplicationServer

T1000 ApplicationServer

870-2706-04 Rev A870-2706-02 Rev BDual Port G-Bit E-NetCard


870-2707-02 Rev A870-2707-01 Rev BModem Card


870-2708-02 Rev A870-2708-01 Rev BQuad Serial Exp. Card


870-2721-04 Rev A870-2721-02 Rev B120 GB Hard DriveAssy

870-1893-03 Rev A870-2754-01 Rev P orT1100 (ApplicationServer - DC)

870-2807-01 Rev A

T1100 (ApplicationServer - DC)

870-2706-04 Rev A870-2706-02 Rev ADual Port Ethernet


870-2787-02 Rev A870-2787-01 Rev BHard Disc Drive - 250GB SATA


870-2833-02 Rev A870-2833-01 Rev C2 GB RAM Kit



GlossaryA

Asynchronous Transfer ModeATM

A packet-oriented transfer mode thatuses an asynchronous time divisionmultiplexing technique to multiplexinformation flow in fixed blocks,called cells.

A high-bandwidth, low-delayswitching, and multiplexingtechnology to support applicationsthat include high-speed data, localarea network interconnection,multimedia application and imaging,and residential applications such asvideo telephony and otherinformation-based services.

C

The application for the ITU SS7signaling links that is used with card

CCS7ITU

types limds0, limch, lime1,and limt1.

Carrier Identification CodeCIC

A 4-digit code that controls therouting applied to a message.

D

Database Communication ModuleDCM

The DCM provides IP connectivityfor applications. Connection to ahost is achieved through an ethernetLAN using the TCP/IP protocol.

Database Service Module.DSM

The DSM provides large capacitySCCP/database functionality. TheDSM is an application card thatsupports network specific functions


D

such as EAGLE ProvisioningApplication Processor (EPAP),Global System for MobileCommunications (GSM), EAGLELocal Number Portability (ELAP),and interface to Local ServiceManagement System (LSMS).

E

The European equivalent of T1 thattransmits digital data over atelephone network at 2.048 Mbps.

E1

EPM-based E1/T1 Multi-ChannelInterface Module

E5-E1T1

An EPM-based card that providesE1 and T1 connectivity. The E5indicates the card is for existingEAGLE 5 control and extensionshelves. E1T1 is an abbreviation forthe ITU E1 and ANSI T1 interfaces.Thus the nomenclature defines theshelves where the card can be usedand the physical interface that itprovides.

EPM-based Ethernet cardE5-ENET

A high capacity single-slot IPsignaling card (EPM card plus GigEthernet PMC cards).

Enhanced Database CommunicationModule

EDCM

Emulated Point CodeEPC

G

Gigabyte — 1,073,741,824 bytesGB

H


GlossaryRelease 43.0 Feature Notice

H

High Capacity Multi-ChannelInterface Module

HC-MIM

A card that provides access to eightE1/T1 ports residing on backplaneconnectors A and B. Each datastream consists of 24 T1 or 31 E1 DS0signaling links assigned in atime-division multiplex (TDM)manner. Each channel occupies aunique timeslot in the data streamand can be selected as a localsignaling link on the interface card.Each card has 8 E1 or 8 T1 portinterfaces with a maximum of 64signaling links provisioned amongthe 8 E1/T1 ports.

High-Speed IMT Packet RouterHIPR

A card that provides increasedsystem throughput and trafficcapacity. HIPR moves EAGLE froman intra-shelf ring topology to anintra-shelf switch topology. HIPRacts as a gateway between theintra-shelf IMT BUS, running at125Mbps, and the inter-shelfoperating at 1.0625Gbps. The HIPRcard will seat in the same slot as anHMUX card (slots xx09 & xx10 ofeach shelf).

High-Speed IMT Packet Router 2HIPR2

A card that provides increasedsystem throughput and trafficcapacity on the existingFibre-Channel ring. A high rateFibre-Channel option of 2.5 Gbps isavailable when an EAGLE isprovisioned with all HIPR2 cards.In a mixed topology where a HIPR2is used in an EAGLE along withHMUX and HIPR, the Fibre-Channelring runs at the lower rate of 1.0625Gbps.



H

High-Speed MultiplexerHMUX

A card that supports therequirements for up to 1500 links,allowing communication on IMTbuses between cards, shelves andframes. HMUX cards interface to 16serial links, creating a ring from aseries of point to point links. EachHMUX card provides a bypassmultiplexer to maintain the ring’sintegrity as cards are removed andinserted into an operational shelf.

High-Speed IMT Multiplexer, areplacement card for the IPMX.

I

Integrated Signaling SystemISS

L

A link interface module (LIM) withthe ATM interface.

LIM-ATM

Local Number PortabilityLNP

M

Maintenance Disk and AlarmMDAL

Multi-Channel Interface ModuleMIM

Multi-port LIMMPL

O

Originating Point CodeOPC

P

Point Code and CIC TranslationPCT

A feature that enables the EAGLE 5ISS to translate the DPC or OPC ofan MTP routed message, and enablesmodification of the CIC of an ISUP



P

message. This gives the EAGLE 5 ISSthe capability to emulate a pointcode using other nodes in itsnetwork.

S

Synchronous E1 High Speed LinkSE-HSL

Format for E1 high-speed signalinglinks where time-slot 0 is used forframing and error control. Theremainder of bandwidth, equivalentto 31 channels of 64Kbps data, isused as a single data link yielding atotal capacity of 1.984 Mbps. Alsoknown as Unchannelized E1.

Signaling System #7SS7

SS7 ANSISS7ANSI

An application used by the LIMcards and the E1/T1 MIM card forthe MTP functionality.

Single Slot Enhanced DataCommunications Module

SSEDCM

Subsystem Prohibited networkmanagement message.

SSP

Subsystem Prohibited SCCP (SCMG)management message. (CER)

T

Transmission Level 1T1

A T1 interface terminates ordistributes T1 facility signals for thepurpose of processing the SS7signaling links carried by the E1carrier.

A leased-line connection capable ofcarrying data at 1,544,000bits-per-second.



T

Terminal Disk ModuleTDM

Time Division Multiplexing

TDM Global Timing InterfaceTDM-GTI

Translation Services ModuleTSM

Provides translation capability andGlobal Title Translation (GTT)implementation for the LocalNumber Portability (LNP) functionand is used for downloadinggateway screening tables to linkinterface modules (LIMs).



Documents

Tekelec EAGLE - Oracle · 2014-10-17 · EAGLE 5 ISS Release 43.0 Feature Content Introduction Feature notices are distributed to customers with each new release of software. This