TEMS Investigation 10.0 Getting Started Manual

TEMS™ Investigation 10.0

Getting Started Manual

This manual is provided by Ascom Network Testing AB without any kind of warranty. Improvements and changes in this description due to typographical errors or inaccuracies in current information, or improvements to programs and/or equipment may be made by Ascom Network Testing AB at any time without notice. These changes will, however, be incorporated into new editions of this manual.

No part of this publication may be reproduced, transmitted, stored in a retrieval system, nor translated into any human or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of the copyrighted owner, Ascom Network Testing AB.

TEMS is a trademark of Ascom.

All other trademarks are the property of their respective holders.

© Ascom 2009. All rights reserved.

Publication number: LZT 108 9985 R1B

Contents

Contents

1. Introduction 1

1.1. What Is the Getting Started Manual? . . . . . . . . . . . . . . . . . . . . . . . . 11.2. What’s in This Manual (and What’s Not) . . . . . . . . . . . . . . . . . . . . . . 11.3. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2. Product Packaging 5

2.1. Base Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52.2. Analysis Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62.3. Replay Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62.4. Further Licensing Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.4.1. Licensing for External Devices . . . . . . . . . . . . . . . . . . . . . . . . 72.4.2. Licensing for AQM (PESQ) . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.4.2.1. Mobile-to-fixed AQM . . . . . . . . . . . . . . . . . . . . . . . . . . 72.4.2.2. Mobile-to-mobile AQM. . . . . . . . . . . . . . . . . . . . . . . . . 8

2.4.3. Network (Floating) Licenses. . . . . . . . . . . . . . . . . . . . . . . . . . 82.5. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3. Configuring the PC for TEMS Investigation Data Collection 9

3.1. Administrator Rights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93.2. Advanced Power Management (APM) . . . . . . . . . . . . . . . . . . . . . . 103.3. Automatic Updating of Software . . . . . . . . . . . . . . . . . . . . . . . . . . . 103.4. AutoPlay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103.5. Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103.6. Documents/My Documents Folder . . . . . . . . . . . . . . . . . . . . . . . . . 103.7. Intel SpeedStep. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113.8. IR Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113.9. Port-scanning Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113.10. RTP (UDP) Ports for Video Streaming . . . . . . . . . . . . . . . . . . . . . 11

LZT 108 9985 R1B i

TEMS Investigation 10.0 Getting Started Manual

3.11. Security Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113.12. Sleep Mode, Screen Savers, Energy Saving Features. . . . . . . . . 123.13. USB Legacy Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123.14. Windows Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123.15. Windows Media Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123.16. Windows Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . 123.17. Windows Vista Specific Settings. . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.17.1. IPv6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133.17.2. Visual Effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.18. Windows XP Specific Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 143.19. WLAN (IEEE 802.11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4. External Equipment 15

4.1. Connectable Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154.1.1. Phones and Data Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.1.1.1. UMTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154.1.1.2. CDMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174.1.1.3. TD-SCDMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.1.2. Fixed Wireless Terminals. . . . . . . . . . . . . . . . . . . . . . . . . . . 174.1.3. AQM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174.1.4. Scanners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.1.4.1. UMTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184.1.4.2. LTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194.1.4.3. CDMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204.1.4.4. WiMAX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.1.5. GPS Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204.2. Capabilities of Phones and Data Cards Sold with TEMS Investigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224.3. Basic Configuration of Phones and Data Cards . . . . . . . . . . . . . . . 234.4. Cables to Use with Phones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234.5. Connecting External Antennas to Phones . . . . . . . . . . . . . . . . . . . 244.6. Scanners. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.6.1. Anritsu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244.6.2. PCTel: General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254.6.3. PCTel SeeGull LX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254.6.4. PCTel SeeGull EX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4.7. DRT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

ii

Contents

5. Installing TEMS Investigation 27

5.1. PC Hardware and Software Requirements . . . . . . . . . . . . . . . . . . . 275.1.1. Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275.1.2. Virtual Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285.1.3. Operating System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295.1.4. Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5.2. Other Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305.3. Installing TEMS Investigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305.4. Installing HASP License Software. . . . . . . . . . . . . . . . . . . . . . . . . . 315.5. Installation of Device Drivers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

5.5.1. Installation of USB Driver for Phones. . . . . . . . . . . . . . . . . . 325.5.2. Installation of USB Driver for PCTel SeeGull LX MM2 Scanners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345.5.3. Installation of USB Driver for PCTel SeeGull EX Scanners. . 355.5.4. Installation of USB Driver for Anritsu ML8740/ML8741 Scanners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355.5.5. Installation of USB Driver for GPS Units . . . . . . . . . . . . . . . 355.5.6. Installation of Driver for USB-to-RS232 Serial Converter in Equipment Cases/Backpack . . . . . . . . . . . . . . . . . . . . . . 355.5.7. Installation of Drivers for AQM Module. . . . . . . . . . . . . . . . . 365.5.8. General Advice on Driver Installation for AQM Equipment Case/Backpack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

5.6. Uninstalling TEMS Investigation . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

6. Installing the Call Generator 38

7. Licensing 39

7.1. Licensing Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397.2. Route Analysis License Requirements . . . . . . . . . . . . . . . . . . . . . . 397.3. Data Collection License Requirements . . . . . . . . . . . . . . . . . . . . . . 407.4. Driver for Hardware Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407.5. The HASP HL SRM Key Reader. . . . . . . . . . . . . . . . . . . . . . . . . . . 40

8. Configuring the PC and Phones for Data Services 41

8.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 418.2. USB Drivers for Phones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

LZT 108 9985 R1B iii


8.3. Configuring Dial-up Networking (RAS) . . . . . . . . . . . . . . . . . . . . . . 428.3.1. Dial-up Networking Configuration in Windows Vista . . . . . . 428.3.2. Dial-up Networking Configuration in Windows XP . . . . . . . . 44

8.4. Setting Up the APN for the Phone (UMTS, RAS) . . . . . . . . . . . . . . 458.4.1. Setup in Phone User Interface. . . . . . . . . . . . . . . . . . . . . . . 458.4.2. Setup Using AT Commands . . . . . . . . . . . . . . . . . . . . . . . . 46

8.5. Configuring Devices for NDIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 478.5.1. Configuration of Sony Ericsson Phones . . . . . . . . . . . . . . . 478.5.2. Configuration of Data Cards . . . . . . . . . . . . . . . . . . . . . . . . 478.5.3. Configuration of Qualcomm TD8200 . . . . . . . . . . . . . . . . . . 48

8.6. Testing Circuit-switched Data Services with UEs . . . . . . . . . . . . . . 488.6.1. Testing Circuit-switched by Placing Video Calls . . . . . . . . . 48

9. PC and Device Configuration for DRT Scanner 49

9.1. Direct Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 499.2. Local Area Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 509.3. Verifying the Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509.4. Scanner Antenna Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

10. PC and Device Configuration for Ericsson Fixed Wireless Terminal 52

10.1. PC Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5210.2. FWT Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

11. Configuring the PC for Python Script Processing 54

12. Cell Data and Maps 55

13. Connecting External Equipment 56

14. Support Contact Information 57

Index 59

iv

Chapter 1. Introduction

1. Introduction

Thank you for choosing TEMS Investigation – the industry-leading tool for troubleshooting, verification, optimization, and maintenance of wireless networks. Offering data collection, real-time analysis, and post-processing all in one, TEMS Investigation is a complete solution for all of a network operator’s daily network optimization tasks. This complete solution eliminates the need for multiple tools, reducing costs and saving time and effort for operations staff.

1.1. What Is the Getting Started Manual?The Getting Started Manual deals with preliminaries that you must work through before you can start using TEMS Investigation, such as configuring your computer and phones. The manual also covers the installation of TEMS Investigation itself.

Most of the procedures described here only have to be performed once, or when you are exchanging pieces of hardware.

The other manuals delivered with the product (Data Collection User’s Manual, Route Analysis User’s Manual, Information Elements and Events) concentrate on how to operate the TEMS Investigation software once you have it installed and all your hardware is ready for use. These manuals are what you will probably be referring to most of the time once you have gotten started.

1.2. What’s in This Manual (and What’s Not)

Main Topics• Contents of TEMS Investigation product packages: chapter 2

• Configuring the PC for TEMS Investigation: chapter 3

• Connectable external devices: chapter 4

• PC hardware and software requirements: section 5.1

LZT 108 9985 R1B 1


• Installing the TEMS Investigation software: section 5.3

• Installing the Call Generator: chapter 6

• Licensing: chapter 7

• Configuring the PC and phones for data services: chapter 8

• Configuring the PC for use with a DRT scanner: chapter 9

• Configuring the PC for use with an Ericsson Fixed Wireless Terminal: chapter 10

• Configuring the PC for Python scripting: chapter 11

Cell Data and MapsThe following tasks may also be regarded as preliminary ones:

• Importing network cell data

• Importing map files

These procedures, however, are not covered here but in the User’s Manuals, since they are handled from within the TEMS Investigation software applications. Chapter 12 gives the appropriate references.

Equipment CasesThe TEMS equipment cases, designed to accommodate phones and other equipment during drive tests, are not covered here but have their own manuals. These, however, sometimes refer to TEMS Investigation documentation.

Installation of drivers for TEMS equipment cases is explained in section 5.5.6.

TEMS PocketCertain Sony Ericsson phones that are connectable in TEMS Investigation have TEMS Pocket functionality. For these phones, a separate User’s Manual deals with the TEMS Pocket functions. However, in the C702, C905(a), K790a, K790i, K800i, W760i and Z750i models, the Pocket functions are disabled when the phone is connected in TEMS Investigation. Nonetheless, it is possible to purchase such phones with fully enabled TEMS Pocket software; see section 2.5.

2

Chapter 1. Introduction

Readme File, Release NoteSome technical issues not addressed in this manual are dealt with in the file Readme.rtf in the TEMS Investigation installation folder. The same information is reproduced in the Release Note issued with the current release.

FAQMany questions regarding TEMS Investigation are answered in the FAQ sections found on the Web at www.ascom.com/en/index/support/support-tems/technical-support/tems-investigation.htm.

Technical SupportIf you have a question about TEMS Investigation which is not answered in any of the manuals nor in any of the other sources mentioned above, please contact technical support. Contact information is given on the Web at www.tems.com under the link “TEMS Sales & Support”.

TEMS On-line Subscription ServiceTo sign up for the TEMS on-line subscription service, please go to www.tems.com and, under the heading “TEMS Subscriptions”, click the link “Register for TEMS Subscription Services”. This free service includes e-mail notification of TEMS product launches, version upgrades and patches, as well as the on-line newsletter TEMS News.

1.3. DefinitionsThis section explains a number of central concepts in TEMS Investigation which are frequently referred to in this manual.

PhoneThe term “phone” covers user terminals from all supported technologies. When a subset is meant, a suitable qualifier is prefixed, and/or a more precise term is used (“GSM phone”, “Sony Ericsson GSM phone”, “Nokia UE”, “Kyocera CDMA phone”, etc.).

Some user terminals supported by TEMS Investigation are in fact data cards rather than phones. The word “terminal” is therefore sometimes used instead of “phone”, without any difference in meaning from the point of view of TEMS Investigation.

LZT 108 9985 R1B 3

http://www.ascom.com/en/index/support/support-tems/technical-support/tems-investigation.htm


http://www.tems.com/



ScannerThe term “scanner” denotes a device dedicated to scanning, for example a PCTel scanner. Phones with scanning capabilities are not referred to as scanners.

Data ServicesThis term refers to services requiring a data connection (either circuit-switched or packet-switched), as opposed to voice calls.

4

Chapter 2. Product Packaging

2. Product Packaging

TEMS Investigation 10.0 is offered in the following types of package:

• Base Packages

• Analysis Packages

• Replay Packages

For all types of package, support for an arbitrary subset of the supported cellular technologies can be purchased. The only dependency is that WCDMA always comes with GSM support included.

For packages that include GSM but not WCDMA, the following holds: Any GSM data collected with equipment that is supported by the product can be analyzed. This means that TEMS Investigation logfiles recorded with WCDMA-capable devices can be opened and replayed, and any GSM data contained in such files can be studied. In the RAN Tuning tool, GSM reports (but not WCDMA reports) can be generated.

2.1. Base PackagesThe following contents are part of all Base Packages:

• CD with TEMS Investigation PC software and installation application

• USB hardware key (HASP HL SRM) where the TEMS Investigation license is stored

• USB hub, 4-port

• TEMS Investigation user documentation in electronic format (*.chm, *.pdf)

Base Packages encompass all TEMS Investigation functionality, including data collection and realtime presentation. However, they do not in themselves include any licenses for connecting external devices; all of these devices require a separate license option as detailed in section 2.4.1. Further license options are offered for collecting data with multiple phones concurrently as well as for AQM; again, see section 2.4.1.

LZT 108 9985 R1B 5


Within the technologies selected in the package, the Base Package license permits loading of logfiles recorded with any equipment that is supported by the product, as well as logfiles from a number of other sourcsee the Data Collection User’s Manual, section 7.4. No device-specific license options are ever required for this.

2.2. Analysis PackagesThe Analysis Packages differ from the corresponding Base Packages in that they do not support data collection or realtime presentation. In all other respects they are identical with the corresponding Base Packages.

These contents are included in all Analysis Packages:




The license delivered with each package permits analyzing of data collected with any equipment supported by the product (for the cellular technologies selected).

2.3. Replay PackagesThese packages give access only to a small part of the TEMS Investigation functionality: a Replay Package license allows replay of TEMS Investigation logfiles in Data Collection. The Route Analysis application is not available in a Replay Package, nor is it possible to do data collection or realtime presentation, nor to replay logfiles from sources other than TEMS Investigation.

These contents are included in all Replay Packages:




2.4. Further Licensing OptionsSee chapter 7, page 39 about how the licensing applies in practice.

6

Chapter 2. Product Packaging

2.4.1. Licensing for External DevicesA separate license option is required for connecting each of the following categories of equipment.

• Sony Ericsson phones (UMTS)

• Motorola phones (UMTS)

• Motorola phones with iDEN capability

• Nokia phones (UMTS) without HSPA capability

• Nokia phones with HSPA capability

• Devices based on Qualcomm HSDPA-capable chipsets (HSDPA but not HSUPA)1

• Devices based on Qualcomm HSPA+ and HSPA-capable chipsets (i.e. supporting at least HSDPA and HSUPA, and possibly HSPA+ as well)1

• Devices based on Qualcomm CDMA-capable chipsets

• Datang phones (TD-SCDMA)

• Anritsu scanners

• PCTel scanners

• DRT scanners

For phones and data cards, the set of license options purchased grant permission to collect data with one device at a time, belonging to one of the selected equipment categories. Further license options are offered for data collection with multiple phones/data cards concurrently.

No restriction on the number of connectable devices applies to scanners (or to GPS units, for which no special license is required).

2.4.2. Licensing for AQM (PESQ)

2.4.2.1. Mobile-to-fixed AQMA separate license option is offered for calculating PESQ and making other audio quality measurements using the downlink and uplink AQM modules. The downlink AQM module is either standalone or installed in a TC-1520B equipment case; the uplink module is housed in a Call Generator. The license

1. These chipsets are listed in section 4.1.1.1.

LZT 108 9985 R1B 7


permits connecting (any number of) downlink AQM modules to the application. All equipment required for AQM, including a cable kit and other accessories, is sold separately.

The AQM option is also required for merging AQM uplink data into logfiles using the Converter tool. (The Analysis Packages always include the AQM option.)

2.4.2.2. Mobile-to-mobile AQMThe same license option also covers mobile-to-mobile AQM.

2.4.3. Network (Floating) LicensesInstead of fixed single-user licenses, the customer can purchase network licenses that can be shared among multiple users. See chapter 7 regarding the practical use and scope of network licenses.

2.5. AccessoriesIn addition to the standard packages and separately purchased phones and scanners, the following optional items can be delivered:

• Equipment cases (with or without AQM modules)

• GPS units

• TEMS Pocket-enabled Sony Ericsson and Nokia phones

• Laptops tested with TEMS Investigation 10.0

• Indoor backpack including battery solution

The indoor backpack contains everything (including battery pack and serial converter) needed to operate a scanner in indoor and pedestrian environments. It accommodates any of the PCTel models as well as a DRT scanner and one standalone downlink AQM module.

Please contact TEMS for further information on the available accessories.

8

Chapter 3. Configuring the PC for TEMS Investigation Data Collection

3. Configuring the PC for TEMS Investigation Data Collection

For TEMS Investigation Data Collection to operate properly, your computer must be appropriately configured in a variety of respects. This chapter is a checklist that you need to go through before installing TEMS Investigation Data Collection.

Further PC configuration, required for data service testing, is described in chapter 8.

General third-party software requirements are listed in section 5.1.4.

If you have not purchased the data collection functionality, you can skip this chapter.

3.1. Administrator RightsA number of user actions in TEMS Investigation require that the user have administrator rights on the PC:

• Running multiple concurrent data service sessions. In the course of such testing, TEMS Investigation must be able to modify Windows routing tables, which requires admin privileges.

• Use of the IP sniffer. See Data Collection User’s Manual, section 20.7.1 and Information Elements and Events, section 8.3.3.

Note: Please read this chapter carefully, since inappropriate PC settings may seriously impair the performance of TEMS Investigation Data Collection, or even render certain functions unusable.

LZT 108 9985 R1B 9


3.2. Advanced Power Management (APM)Advanced Power Management (APM) should be disabled if possible, since it may cause external devices to disconnect from TEMS Investigation. The reason this can happen is that APM sometimes switches off the communication circuits to save power. This may occur even when a phone is connected and communicates with the PC on a regular basis. For information on how to disable APM in BIOS, please consult the user manual for your computer.

3.3. Automatic Updating of SoftwareSoftware that uses an “auto update” function to receive automatic updates from a web site over a dial-up connection should be disabled.

3.4. AutoPlayAutomatic launching of a PC application following device connect must be avoided. Therefore, make sure that for all connected devices used with TEMS Investigation, the AutoPlay option “Take no action” is selected.

In Windows Vista, these settings are found under Control Panel → AutoPlay.

In Windows XP, right-click each device in Explorer and select Properties → AutoPlay tab.

3.5. BluetoothIf Bluetooth is not needed on the PC, it should be disabled.

If a GPS unit or other equipment (keyboard, mouse, etc.) is connected to the PC via Bluetooth, you should disable the autodetect function in TEMS Investigation for all ports that you are not going to use in the application. See Data Collection User’s Manual, section 6.9.4.

This is to minimize interference from Bluetooth transmissions in the cellular network air interface.

3.6. Documents/My Documents FolderTEMS Investigation places certain files under “Documents” (Windows Vista) or “My Documents” (Windows XP) in a subfolder called “TEMS Product Files”. If your Documents or My Documents folder is located on a network

10


drive, be sure to make the folder available offline before disconnecting from the network (for example, when going drive testing).

3.7. Intel SpeedStepIf the PC is equipped with Intel’s SpeedStep technology regulating the processor speed, choose the setting “Maximum Performance” for all types of operation (“Plugged in”, “Running on batteries”).

3.8. IR PortThe IR port on your PC may need to be disabled, since it may interfere with the ordinary COM ports. Please consult the user manual for your computer regarding how to disable the IR port.

3.9. Port-scanning SoftwareYou should not have any software installed that periodically scans COM or USB ports, for instance Microsoft Outlook synchronization software such as Sony Ericsson PC Suite or Nokia PC Suite. The reason is that such software may cause difficult connect problems in TEMS Investigation Data Collection.

3.10. RTP (UDP) Ports for Video StreamingBy default TEMS Investigation uses RTP (UDP) ports 5004–5007 for video streaming. If you intend to accept this default setting, you must make sure that the ports have not been reserved by some other application. You can specify a different port usage in the Video Streaming command in a command sequence; see the Data Collection User’s Manual, section 14.12.2.10.

3.11. Security ProductsPlease note that hard disk encryption software, firewalls, virus scanners, and other security products may prevent multiple RAS sessions from being maintained concurrently, thus interfering with data service testing. Contact your IS/IT department for assistance in these matters.

The realtime scanning feature of antivirus software is prone to generate considerable CPU load. If you find the overall CPU load excessive, it may be a good idea to try turning off the realtime scanning feature.

LZT 108 9985 R1B 11


3.12. Sleep Mode, Screen Savers, Energy Saving Features

You should make sure that the computer used for measurement and recording does not go into any kind of standby mode:

• Never put the PC in Sleep mode.

• Disable the Windows screen saver under Control Panel → Display → Screen Saver. In the same dialogs, make appropriate settings under “Energy saving features...” so that these features are never activated during measurement.

• Disable any other screen savers.

(If the PC does go into standby, it may be necessary to unplug your data collection devices and plug them in again.)

3.13. USB Legacy SupportUSB Legacy Support must be turned off in BIOS. For information on how to do this, please consult the user manual for your computer.

3.14. Windows FirewallThe built-in software firewall in Windows Vista and Windows XP must be disabled.

3.15. Windows Media PlayerWindows Media Player and other applications that attempt to synchronize to removable mass storage devices (such as mobile phones) must be disabled. They may otherwise interfere with data collection.

3.16. Windows Power ManagementYou must disable all power management routines in Windows. For further instructions, please consult the documentation for the variety of Windows you are using.

12


3.17. Windows Vista Specific Settings

3.17.1. IPv6It is recommended to disable IPv6 for the modem of each connected device. If this is not done, the CPU load will rise appreciably, and dial-ups will take considerably longer to complete.

• Open the Control Panel and select Network and Sharing Center → Manage network connections.

• Right-click the modem and open its Properties dialog.

• Select the Networking tab.

• Uncheck “Internet Protocol Version 6 ...”.

Alternatively, in the registry, locate the folder

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\tcpip6\Parameters\

and in that folder create a new key DisabledComponents and set it to the value FF (meaning “Disable IPv6 over all interfaces”).

See also section 8.3.1, step 15.

3.17.2. Visual EffectsFor performance reasons, it is strongly recommended that you disable the Windows Aero color scheme (making window frames translucent and producing other visual effects).

To obtain the best possible TEMS Investigation performance, configure visual effects as follows (this will among other things turn Windows Aero off):

• Open the Control Panel and select System.

• Click “Advanced system settings”. The System Properties dialog opens.

• Select the Advanced tab.

• In the Performance section, click the Settings button.

• Select the Visual Effects tab. The default setting here is “Let Windows choose what’s best for my computer”. Change this to “Adjust for best performance”.

LZT 108 9985 R1B 13


3.18. Windows XP Specific SettingsVisual effects and other “bells and whistles” in the Windows XP user interface should be disabled.

3.19. WLAN (IEEE 802.11)If WLAN is not needed on the PC, it should be disabled in order to minimize interference from WLAN transmissions in the cellular network air interface.

14

Chapter 4. External Equipment

4. External Equipment

This chapter gives an overview of the external devices that can interact with TEMS Investigation Data Collection.

4.1. Connectable EquipmentFor a complete and up-to-date list of equipment connectable in this and other TEMS products, please visit our website at www.ascom.com/en/index/support/support-tems/technical-support/tems-investigation.htm.

4.1.1. Phones and Data Cards

4.1.1.1. UMTSThe following phones and data cards (supporting both GSM and WCDMA unless otherwise stated) can be delivered with TEMS Investigation 10.0:

• Sony Ericsson C905

• Sony Ericsson C905a

• Sony Ericsson Z750i

• Nokia N96 EU

• Nokia N96 US

Other Connectable UMTS Devices• Sony Ericsson C702

• Sony Ericsson K600i

• Sony Ericsson TM506

• Sony Ericsson W760i

• LG CU320

• LG CU500

LZT 108 9985 R1B 15




• LG U960

• Motorola E1000

• Motorola E1070

• Motorola M2501

• Motorola Razr Maxx V6

• Motorola Razr V3x

• Motorola Razr V3xx

• Motorola Razr2 V9

• Nokia 6120

• Nokia 6121

• Nokia 6280

• Nokia 6680

• Nokia 7376

• Nokia N75

• Nokia N80

• Nokia N95

• Certified devices based on Qualcomm HSDPA capable chipsets, including: MSM6246/6260/6275/6280/6281

• Certified devices based on Qualcomm HSPA capable chipsets (supporting both HSDPA and HSUPA), including: MSM6290/7200/7201/7201A/7225

• Certified devices based on Qualcomm HSPA+ capable chipsets, such as MDM8200

If a Qualcomm chipset based device that you want to connect is not detected by TEMS Investigation, run the ManualUEConfig.exe utility to assist the application in recognizing the device. See the Data Collection User’s Manual, section 6.7 for details.

Other Connectable GSM Phones• Nokia 6086 (GSM/GAN)

• Nokia 6125

• Sony Ericsson K790a

16


• Sony Ericsson K790i


• Nokia 6230i

4.1.1.2. CDMA• Certified devices based on Qualcomm 1x (cdma2000) capable chipsets:

MSM5100

• Certified devices based on Qualcomm EV-DO Rev 0 capable chipsets: MSM6125/65x0

• Certified devices based on Qualcomm EV-DO Rev A capable chipsets, including: MSM6800/6800A, QSC6085

If a Qualcomm chipset based device that you want to connect is not detected by TEMS Investigation, run the ManualUEConfig.exe utility to help the application recognize the device. See the Data Collection User’s Manual, section 6.7 for details.

4.1.1.3. TD-SCDMA• Datang LC8130E

4.1.2. Fixed Wireless TerminalsThe following Ericsson Fixed Wireless Terminals can be connected:

• W21

• W25

4.1.3. AQM ModulesAQM modules (either standalone or mounted in a TC-1520B equipment case) can be connected.

LZT 108 9985 R1B 17


4.1.4. Scanners

4.1.4.1. UMTSThe following scanners can be delivered with TEMS Investigation 10.0. (Bands given below are downlink bands; WCDMA 1800 [Band III] is identical to what is referred to in Japan as WCDMA 1700 [uplink band of Band III].)

• PCTel SeeGull LX GSM 850/1900

• PCTel SeeGull LX GSM 900/1800

• PCTel SeeGull LX WCDMA 850/2100

• PCTel SeeGull LX WCDMA 850 + GSM 900/1800

• PCTel SeeGull EX WCDMA 2100 AWS (Band IV) + GSM 1900

• PCTel SeeGull EX WCDMA 2100 AWS (Band IV) + GSM 850/1900

• PCTel SeeGull EX WCDMA 2100 + GSM 900/1800

• PCTel SeeGull EX WCDMA 850/1900 + GSM 850/1900

• PCTel SeeGull EX WCDMA 900/2100 + GSM 900/1800

• PCTel SeeGull EX Mini WCDMA 2100

• PCTel SeeGull EX Mini WCDMA AWS (Band IV)

• PCTel SeeGull EX Mini WCDMA 900/2100

• PCTel SeeGull EX Mini WCDMA 850/1900

The following UMTS phones for sale with TEMS Investigation 10.0 are capable of WCDMA scanning:


• Sony Ericsson C905a


Regarding GSM scanning capabilities of UMTS phones, see section 4.2.

Other Connectable UMTS Scanners• Anritsu ML8720 WCDMA 2100

• Anritsu ML8740B Area Scanner (WCDMA 2100)

• Anritsu ML8740B Second RF Option (WCDMA 2100)

18


• Anritsu ML8741B Area Scanner 2100 (1 Pilot)

• Anritsu ML8741B Area Scanner 2100 (2 Pilots)

• Anritsu ML8741B Area Scanner 1800 (1 Pilot)

• Anritsu ML8741B Area Scanner 1800 (2 Pilots)

• Anritsu ML8741B Area Scanner 1800/2100 (1 + 1 Pilot)

• PCTel SeeGull LX WCDMA 850





• PCTel SeeGull LX WCDMA 2100 Band IV

• PCTel SeeGull LX Plus WCDMA 2100

• PCTel SeeGull LX WCDMA 850/1900



The following UMTS phones (no longer for sale with TEMS Investigation) are capable of WCDMA scanning:



4.1.4.2. LTEThe following scanners can be delivered with TEMS Investigation 10.0:

• DRT4301A+ LTE 700/850/1900/2100 AWS

• DRT4301A+ LTE 900/1800/2100 AWS/2600

• PCTel SeeGull EX LTE Upper 700-C/Lower 700-A/B/C (DL/UL)

• PCTel SeeGull EX LTE Upper 700-C/2100 AWS (DL)

• PCTel SeeGull EX LTE 1800/2600 (DL)

• PCTel SeeGull EX Mini LTE Lower 700-A/B/C (DL/UL)

• PCTel SeeGull EX Mini LTE 2600 (DL)

LZT 108 9985 R1B 19


4.1.4.3. CDMAThe following scanners can be delivered with TEMS Investigation 10.0:

• PCTel SeeGull LX 1x 450

• PCTel SeeGull LX EV-DO 450

• PCTel SeeGull LX 1x 450 + EV-DO 450

• PCTel SeeGull EX 1x 850/1900 EV-DO 850/1900 DL

Other Connectable CDMA Scanners• PCTel SeeGull LX 1x 800

• PCTel SeeGull LX 1x 1900

• PCTel SeeGull LX 1x 800/1900

• PCTel SeeGull LX EV-DO 800/1900

• PCTel SeeGull LX 1x 800/1900 + EV-DO 800/1900

4.1.4.4. WiMAXThe following scanners can be delivered with TEMS Investigation 10.0:

• DRT4301A+ WiMAX 2.5/3.5 GHz

• DRT4301A+ WiMAX 2.3/2.5 GHz

4.1.5. GPS UnitsTEMS Investigation supports the NMEA-0183 GPS protocol.

Some other GPS units using a different protocol are also compatible with TEMS Investigation, including the GPS built into the supported PCTel scanners.

This is the full list of recommended GPS units:

• Bosch/Blaupunkt TravelPilot

• Garmin 10 Mobile Bluetooth (NMEA-0183)

• Garmin 12XL (NMEA-0183)

• Garmin 35 (NMEA-0183)

• GlobalSat BT-359 (NMEA-0183)

• GlobalSat BT-368 (NMEA-0183)

20


• GlobalSat BU-303 (NMEA-0183)

• GlobalSat BU-353 (NMEA-0183)

• Holux GPSlim 236 (NMEA-HS; Bluetooth or USB)

• Magnetti Marelli RoutePlanner NAV200

• Nokia LD-3W Bluetooth (NMEA-0183)

• Sanav GM-44 (NMEA-0183)

• Sanav GM-158 (NMEA-0183)

For poor receiving conditions one of the products Bosch/Blaupunkt TravelPilot or Magnetti Marelli RoutePlanner can be recommended, since they have dead reckoning facilities.

LZT 108 9985 R1B 21


4.2. Capabilities of Phones and Data Cards Sold with TEMS Investigation

This section is restricted to devices that can be delivered with TEMS Investigation 10.0.

General Capabilities

GSM Capabilities

Phone/Feature

Sony Ericsson C905 3.6

Sony Ericsson C905a 3.6

Sony Ericsson Z750i 1.8

Nokia N96 EU 3.6

Nokia N96 US 3.6

Option GT Expr. HSUPA 7.2 2.00

Phone/Feature GPRS TSDL+UL

EGPRS TSDL+UL

GSM Scanning

Sony Ericsson C905(a) 4+1/3+2 4+1/3+2

Sony Ericsson Z750i 4+1/3+2 4+1/3+2

Nokia N96 EU/US 5+1/4+2/3+3 5+1/4+2/3+3

Option GT Express HSUPA

4+1/3+2/2+3/1+4

4+1/3+2/2+3/1+4

HSD

PA, M

bit/s

HSU

PA, M

bit/s

WC

DM

A 8

50 (V

)W

CD

MA

900

(VIII

)W

CD

MA

190

0 (II

)W

CD

MA

210

0 (I)

GSM

850

GSM

900

GSM

180

0G

SM 1

900

Exte

rnal

Ant

enna

AQ

MSc

anni

ng

22


4.3. Basic Configuration of Phones and Data Cards

Sony Ericsson C905, C905aSony Ericsson C905/C905a TEMS phones have a special setting “USB Speed”, found under Menu → Settings → Connectivity tab → USB. The choices are High Speed (480 Mbit/s) and Full Speed (12 Mbit/s).

• Select High Speed when running HSDPA in order to achieve the best possible throughput.

• Select Full Speed when the phone is using GSM 850 or 900 in an area where it is forced to transmit at maximum power. If High Speed is used in such situations, the GSM transmissions will interfere with the USB connection, so that logfiles may be lost and the USB connection may possibly break down, necessitating a reboot of both phone and PC.

Before changing the setting, make sure the USB cable is disconnected from the phone. After you make the change, the phone will reboot automatically. This takes some time (about 15 s).

Nokia PhonesThe Net Monitor function in Nokia phones (if present) must be turned off.

Qualcomm Chipset Based DevicesSome commercial Qualcomm chipset derived phones and data cards may not have diagnostics reporting enabled by default, and Ascom is not at liberty to distribute information on how to enable this function. Customers desiring to use such devices with TEMS Investigation therefore need to contact the relevant supplier or operator in each case.

4.4. Cables to Use with Phones

Sony Ericsson C702, C905, C905a, TM506, W760i, Z750iIt is necessary to use the USB cable supplied with the phone (DCU-65, part number RPM 131 12/1 R1B). Using a USB cable delivered with older phones such as K800i and K790i/a is not recommended.

LZT 108 9985 R1B 23


4.5. Connecting External Antennas to PhonesAn external monopole antenna is connected to a phone by means of a coaxial cable (and possibly an adapter) supplied with the phone.

Phone-specific details are as follows:

Sony Ericsson Z750iWhen ordering an external antenna with the Sony Ericsson Z750i, the phone is delivered with the antenna adapter already mounted. Just connect the antenna to the adapter.

A Sony Ericsson Z750i phone with an external antenna mounted cannot use its internal antenna.

Nokia N96Press the antenna adapter into the hole provided for it, then connect the antenna to the adapter.

4.6. Scanners

4.6.1. AnritsuAn RF antenna as well as all necessary adapters and other accessories are included in the package.

Anritsu ML8720: Basic ConfigurationThe serial port baud rate must be set to 115200 in the scanner. Proceed as follows:

• From the scanner main menu, select System Configuration, then select Interface and Behavior.

• Set the COM1 protocol to Direct.

• Set the COM1 baud rate to 115200.

• Set COM1 stop bit(s) to 1.

• Set COM1 data length to 8.

• Set COM1 parity to None.

24


• From the side menu (operated with buttons on the side of the scanner), select OK.

Anritsu ML8720: CableA null modem cable must be used to connect the Anritsu ML8720 to the PC.

4.6.2. PCTel: GeneralAny PCTel scanner can be carried in a TEMS Indoor Backpack (see section 2.5), which includes a battery pack.

A battery pack is also obtainable as a separate add-on.

4.6.3. PCTel SeeGull LXAll PCTel SeeGull LX scanners have an RF antenna included in the package. WCDMA scanner packages furthermore contain a GPS antenna.

MM2 scanners are equipped with a USB power cable. Dual- and single-band scanners are powered through a serial cable.

Single-band WCDMA and CDMA scanners and dual-band GSM scanners are delivered with a mounting kit for installation into a TC-1450 equipment case. MM2 scanners can be mounted into a TC-1520 or TC-1520B equipment case (where the mounting kit accompanies the case).

The following functions can be added as options for GSM-capable scanners:

• GSM C/I measurement

• GSM System Information decoding (“GSM BCCH Type 3”)

4.6.4. PCTel SeeGull EXThe PCTel SeeGull EX scanner has two RF antennas included in the package, as well as a USB cable, a power cable, and a GPS antenna. The EX Mini has only one RF component and hence only one RF antenna.

The scanner can be mounted into a TC-1520 or TC-1520B equipment case (where the mounting kit accompanies the case).

The following functions can be added as options:

• GSM C/I measurement (for GSM-capable scanners)

LZT 108 9985 R1B 25


• GSM and WCDMA System Information decoding (“Layer 3 WCDMA/GSM”)

• Spectrum analysis

4.7. DRTThe DRT4301A+ scanner package includes:

• LTE/WiMAX antenna suitable for the selected technology and frequency band(s)

• GPS antenna

• Power cable with vehicle power termination

• Universal AC power adapter

• 100Base-T crossover RJ-45 male data cable

26

Chapter 5. Installing TEMS Investigation

5. Installing TEMS Investigation

This chapter covers requirements on the PC, installation of the TEMS Investigation software, and other installation issues.

Note that before you can run data services, you must also work through chapters 8 and 13.

5.1. PC Hardware and Software Requirements

5.1.1. HardwareTEMS Investigation 10.0 is designed to run on a standard PC and interfaces with the connected devices through USB or serial ports.

If network licenses (see section 7.1) are to be used, the PC hosting the license server must have at least one free USB port.

Data Collection RequirementsProcessor and RAM requirements are strongly dependent on what external devices are connected and what tasks they perform. The recommended minimum configuration is: Pentium T7200 or AMD TL-58 class CPU, preferably with dedicated graphics card from ATI or nVidia; 1 GB RAM.

Other hardware requirements:

• One USB port for each phone

• One USB port for each standalone AQM module

• USB port for PCTel SeeGull LX MM2 scanner

• USB port for PCTel SeeGull EX scanner

• USB port for Anritsu ML8740/ML8741 scanner

• USB port for equipment case

• USB port for HASP HL SRM hardware key

• USB port or serial port for GPS

LZT 108 9985 R1B 27


• Serial port for PCTel SeeGull LX dual-band/single-band scanner

• Serial port for Anritsu ML8720 scanner

• Ethernet port for DRT scanner

• ExpressCard/34 slot or PC Card slot for any data card user terminals

• Sound card and loudspeakers for event audio indications

• Enough disk space to accommodate temporary files created during logfile recording and replay

Route Analysis RequirementsThe Route Analysis application will run smoother the more RAM the PC has.

General Requirements

• Graphics: 1024 × 768 (SVGA) with at least 16 bit colors (High Color)

5.1.2. Virtual MemoryThe virtual memory size of the PC must satisfy certain requirements.

In Windows Vista this can be left to automatic management by the OS.

In Windows XP it is necessary to set the virtual memory size manually. Proceed as follows:

• Open the Control Panel and double-click System.

• Click the Advanced tab, then click Performance Options.

• Under Virtual Memory, click Change.

Note: During drive testing, it must be ensured that the PC and all devices connected to it have adequate power supply for the duration of the test. This is especially important to bear in mind if you are using a USB hub that is not self-powered (i.e. has no external power supply). With multiple devices connected, it may even be necessary to take the precaution of providing extra power via UPS or extra batteries during drive testing. If the power provided is insufficient, problems may arise with device drivers, which in turn may cause malfunctions in Windows and possibly data loss. Ascom takes no responsibility for such data loss.

28


• In the Virtual Memory dialog, make sure that “Initial size” is larger than “Recommended” and that “Maximum size” is much larger than “Initial size”.

5.1.3. Operating SystemThe following operating systems are supported:

• Windows Vista with Service Pack 1, Enterprise Edition

• Windows XP Professional with Service Pack 3

• Windows XP Tablet PC Edition with Service Pack 3

In addition, all the latest Windows updates should always be installed.

Supported languages are English (U.S.), Chinese (simplified characters), and Japanese.

5.1.4. SoftwareBelow is a list of other third-party software that is required for various tools and actions in TEMS Investigation. When installing third-party software, administrator rights are required, and in Microsoft Vista the installation must be run using the “Run as administrator” option.

• The .NET Framework version 3.5 must be installed on the PC. It is included on the TEMS Investigation installation CD.

• Internet Explorer 6.0 or higher required for Report Generator and online help

• Python 2.5 interpreter required for script processing of logfiles and for conversion of CDMA cell files in TEMS Investigation CDMA CSV format (both managed from the Converter tool). A Python interpreter is downloadable from www.python.org/download/. See also chapter 11, “Configuring the PC for Python Script Processing”.

• Microsoft Core XML Services (MSXML) 6.0 required for support of XML-format cell files if Windows XP is used. (In Windows Vista, MSXML 6.0 is included.)

• Microsoft DirectX 9.0c required for video streaming measurements

• For the RAN Tuning tool in Route Analysis, the following is needed:

– Microsoft Office 2007 or Microsoft Office 2003

LZT 108 9985 R1B 29

http://www.python.org/download/


– Microsoft Word, Microsoft Excel, and Microsoft Graph (from Office tools)

– Microsoft Access or MDAC

5.2. Other Hardware Requirements• For audio quality measurements a Call Generator is needed. See

chapter 6.

• For video streaming measurements a streaming server is needed: Darwin Streaming Server (version 5.5.5) or Helix Mobile Server (version 10 or 11).

5.3. Installing TEMS InvestigationYou must have administrator rights on the PC to be able to install TEMS Investigation.

• Insert the installation CD.

– In Windows XP, start the installation when prompted, or open folder and click the option “Open folder...”, then right-click the file TEMS Investigation 10.0.exe and select Run.

– In Windows Vista, click the option “Open folder to view files”, then right-click the file TEMS Investigation 10.0.exe and select “Run as administrator”.

Route Analysis and Data Collection will now be installed, by default to the directory C:\Program Files\Ascom\TEMS Products\TEMS Investigation. (Data Collection is installed even if you have not purchased the data collection functionality, since certain other functions are available anyway; see section 7.3.)

A number of utilities are also installed:

• HASP HL SRM Key Reader, used to inspect the license options encoded in the HASP hardware key. See section 7.5.

• HASP SRM Remote Update, used to update license options in HASP hardware keys. See the document “TEMS HASP HL SRM Hardware Key Info” which is found on the installation CD in the subdirectory Documents.

• Manual UE Configuration, used to assist TEMS Investigation in detecting certain types of devices. See section 5.5.1 of this volume and section 6.7 of the Data Collection User’s Manual.

30


• TEMS Pocket Positioning Tool, used to assign geographical coordinates to TEMS Pocket logfiles recorded by pinpointing (no GPS). See the TEMS Pocket Positioning Tool User’s Manual, included on the installation CD in the subdirectory Documents.

Once installed, the applications and utilities can be run by choosing Start → Programs → Ascom → TEMS Products.

5.4. Installing HASP License SoftwareRegarding licensing in general and hardware key use, see chapter 7.

The HASP HL SRM driver is installed automatically on the PC along with the Route Analysis application. If you are going to use a local license (hardware key plugged into the PC), you need not do anything further.

If network licenses are to be used (see section 7.1), the HASP HL SRM driver also needs to be installed on the machine hosting the license server. This driver is available separately, by default in the directory <TEMS Investigation install dir>\Drivers\HASP; compare the introductory note in section 5.5.1. (Installing the HASP HL SRM driver always installs both client and server software.) Furthermore, depending on the network topology and license server setup, clients may require special configuration. For both servers and clients, HASP HL SRM is configured through a web page interface which has the address

http://localhost:1947/_int_/devices.html

Please refer to the documentation on this web page for details on HASP installation and configuration.

LZT 108 9985 R1B 31


5.5. Installation of Device Drivers

5.5.1. Installation of USB Driver for PhonesUSB drivers are provided for all UMTS terminals that can be purchased with TEMS Investigation. For other UMTS terminals and for all CDMA terminals, drivers must be obtained from the supplier.

The first time you plug in a phone, you will be prompted to locate its driver by browsing to the correct directory. On your doing so the driver will be installed. Supplier- and phone-specific details follow below.

If other drivers are already installed on the PC, make sure that the correct driver becomes associated with the phone modem. Also make sure that you do not install other (non-TEMS-compatible) drivers from the same supplier later on.

Sony Ericsson PhonesWhen prompted, point to ...\Drivers\Sony Ericsson\<model name>.

Datang PhonesBefore plugging in the phone, do as follows:

• Install the driver delivered with the Datang phone.

• After completing the driver installation, go to the directory <TEMS Investigation install dir>\Application and run the file DatangPostInstall.exe. This EXE writes the AT command

AT+CGDCONT=1,"IP","cmnet",,,;+CGEQREQ=1,4

to the registry, thereby accomplishing two things:

– Changing the number of available Datang ports from 3 (default) to 4 (the number of ports needed by TEMS Investigation).

Note: The drivers are delivered on a separate CD in a ZIP archive. You must insert this CD manually after installing TEMS Investigation and unpack the ZIP archive to a location of your choice, for example: C:\Program Files\Ascom\TEMS Products\TEMS Investigation\Drivers.

32


– Setting the APN to the string cmnet for all Datang data modems. If you want to name the APN differently, run DatangPostInstall.exe from a Windows command prompt with the desired APN name as argument, for example: DatangPostInstall myapn. Compare section 8.4.2.

• Now plug in the phone.

• Finally, run the file ManualUEConfig.exe which is also found under <TEMS Investigation install dir>\Application.

• Click the New button. This dialog appears:

Name Enter a name for the phone. (The string does not show anywhere else in TEMS Investigation.)

Type Select “TD-SCDMA Datang”.

Air Interface Port Select the port to use for air interface measurements. (Consult Datang documentation to find this out.)

Data Port Select the port to use for data service measurements.

AT Port Select the port to use for AT commands.

Control Port Select the port to use for video call setup.

UE Id Port Select the physical USB port here.

LZT 108 9985 R1B 33


Motorola PhonesBefore plugging in the phone, you must run one of the MSI files found in the directory ...\Drivers\Motorola. Which file to run depends on the PC hardware architecture.

This installs the driver files to the directory C:\Program Files\Common Files\Motorola Shared\MotPCSDrivers. Go to this directory and run the file Motorola Driver Installer.exe. After the Motorola DriverInstaller has finished, select “Clean and Reinstall”, then click “Start”.

After plugging in the phone, when the Found New Hardware dialog appears, select the option that allows Windows to automatically detect the drivers.

Nokia PhonesBefore plugging in the phone, you must run the MSI file found in the directory ...\Drivers\Nokia. This installs the driver files to the directory C:\Program Files\Nokia\Connectivity Cable Driver.

After plugging in the phone, point to this directory when prompted. You must also select “PC Suite” in the menu that appears in the phone display.

Qualcomm Chipset Based DevicesThis applies to all supported Qualcomm chipset based devices.

Before plugging the device into the PC, use the software application delivered with the device to install the requisite driver.

Regarding the possible use of the ManualUEConfig.exe utility, see the Data Collection User’s Manual, section 6.7. (Normally it is not needed.)

5.5.2. Installation of USB Driver for PCTel SeeGull LX MM2 Scanners

PCTel SeeGull LX MM2 scanners use an Edgeport USB driver.

Note: Standard USB drivers from Nokia should never be installed. With such drivers it is not possible to associate the Nokia GSM phone with two devices (“MS” and “DC”) in TEMS Investigation. Be aware that such drivers are installed along with certain other software products, such as the Nokia PC Suite for synchro-nization with Microsoft Outlook.

34


The first time you plug in the scanner, you will be prompted to locate its driver. Point to the directory ...\Drivers\PCTEL\LX\MM2\Edgeport.

5.5.3. Installation of USB Driver for PCTel SeeGull EX Scanners

PCTel SeeGull EX scanners use a PCTel-specific USB driver, found in the directory ...\Drivers\PCTEL\EX. For instructions on how to install this driver, see the readme document which is supplied in the same directory.

5.5.4. Installation of USB Driver for Anritsu ML8740/ML8741 Scanners

The first time you plug in the scanner, you will be prompted to locate its driver. Point to the directory ...\Drivers\Anritsu.

5.5.5. Installation of USB Driver for GPS UnitsThis section tells how to install a USB driver for various USB GPS units delivered with older versions of TEMS Investigation. The first time you plug in the GPS, you will be prompted to locate its driver.

San Jose Navigation• When prompted, point to the directory ...\Drivers\SANAV USB GPS.

SiRF Star Chipset Based USB GPS• When prompted, point to the directory ...\Drivers\SiRF Star USB GPS.

5.5.6. Installation of Driver for USB-to-RS232 Serial Converter in Equipment Cases/Backpack

This section applies equally to the TC-1520 (non-AQM) and TC-1520B (AQM) equipment cases and to the TEMS Indoor Backpack. It does not apply to older equipment cases, for which different drivers are used.

In order for the PC to detect the COM port of the USB-to-RS-232 serial converter in the equipment case or backpack, some driver files must be installed on the PC. These drivers are always delivered along with the case; they are also found in the directory ...\Drivers\TEMS Case USB to RS232.

LZT 108 9985 R1B 35


The first time you connect the case or backpack to the PC, you will be prompted to locate the driver directory; on your doing so the driver will be installed.

5.5.7. Installation of Drivers for AQM ModuleThe AQM modules, whether standalone or mounted in the TC-1520B equipment case, need to be initialized by dedicated driver files. The AQM module does not have any non-volatile memory, so all requisite software and settings must be downloaded to the AQM module each time it is powered on.

The first time you connect the case or backpack to the PC, you will be prompted to locate the following drivers:

• When prompted the first time, point to the directory ...\Drivers\AQM\PESQ_CONFIGURATION. This driver configures filter parameters, signal levels, and other settings for AQM.

• When prompted the second time, point to the directory ...\Drivers\AQM\PESQ_DSP. This driver contains the AQM software.

5.5.8. General Advice on Driver Installation for AQM Equipment Case/Backpack

When preparing a TC-1520B equipment case for use, we recommend that you proceed in the steps described below. The same advice applies to a backpack with AQM modules installed.

• Before plugging the case into the PC, make sure

– that you have installed TEMS Investigation (section 5.3)

– that you have installed all driver files from the separate driver CD (section 5.5.1)

– that you have rebooted the PC.

• Connect the case to the PC while the case is turned off and does not have any phones installed.

• Power on the case.

• Locate all of the drivers in sections 5.5.6 and 5.5.7.

• After the drivers for AQM have been activated, install one phone at a time in the case. For each phone, you will be prompted to locate the phone

36


driver (see section 5.5.1). Wait each time until the phone driver has been activated before you install the next phone.

5.6. Uninstalling TEMS InvestigationTo uninstall TEMS Investigation software, follow the steps below.

• Open the Windows Control Panel.

• Select Programs and Features (Windows Vista) or Add/Remove Programs (Windows XP).

• Select TEMS Investigation 10.0 in the list of installed programs. Click Uninstall (Windows Vista) or Change/Remove (Windows XP) and confirm removal if prompted to do so. The software will now be uninstalled.

LZT 108 9985 R1B 37


6. Installing the Call Generator

To perform audio quality measurements (AQM) you need a Call Generator. How to install this component is described in the document Call Generator Installation Guide, which is included in the Call Generator sales package. This document also states PC hardware and operating system requirements posed by the Call Generator installation.

38

Chapter 7. Licensing

7. Licensing

This chapter describes the fundamentals of the licensing in TEMS Investigation 10.0.

Regarding the permissions granted by the basic licenses, see sections 2.1 and 2.2. Regarding the range of additional license options, see section 2.4.

The installation of license software is covered in section 5.4.

7.1. Licensing OptionsThere are two types of license that can be associated with a TEMS Investigation application:

• a local license, embodied in a hardware key which is inserted into the PC. A single hardware key controls all aspects of each local license (accessibility of data collection and realtime presentation functions; accessibility of technology-specific functions and data; connectability of external devices).

• a network (or floating) license, obtained by connecting to a license server where the hardware key is inserted.

7.2. Route Analysis License RequirementsA license is always required to run Route Analysis. Without a license you cannot launch the application.

Route Analysis can use either a local license or a network license (see section 7.1).

To analyze data originating from a particular cellular technology, the package you have purchased must support that technology. For example, a license covering WCDMA is required for analysis of WCDMA data (including the WCDMA report in the RAN Tuning tool).

LZT 108 9985 R1B 39


7.3. Data Collection License RequirementsA license is always required to run Data Collection Analysis. Without a license you cannot launch the application.

Device Connect and Logfile RecordingFor a device to be connectable in Data Collection, it must be covered by your license options. See section 2.4.1.

Logfile LoadWithin the confines of the cellular technologies supported in the package, it is possible in Data Collection to load and replay logfiles recorded with devices for which you have no license. For example, even if you have not purchased the license option for data collection with Qualcomm devices, you can still replay logfiles recorded with Qualcomm devices.

Loading of logfiles recorded with software other than TEMS Investigation, however (e.g. TEMS Automatic), requires a Base Package or Analysis Package license.

Local vs. Network LicenseFor connecting external devices Data Collection can only use a local license.

For all other functions, Data Collection can use either a local license or a network license.

7.4. Driver for Hardware KeyThe hardware key driver is installed automatically along with TEMS Investigation.

7.5. The HASP HL SRM Key ReaderYou can check what is covered by your (local or network) license by running the HASP HL SRM Key Reader. This tool is launched by choosing Start → Programs → Ascom → TEMS Products → Utilities. When the tool has started up, enter the File menu and choose Read Hasp Keys.

40

Chapter 8. Configuring the PC and Phones for Data Services

8. Configuring the PC and Phones for Data Services

In this chapter it is assumed that TEMS Investigation has been installed (section 5.3). Naturally, all that is said here is relevant for the Data Collection module only.

8.1. IntroductionThe present chapter describes how to configure your PC and phones for running data services.

Most of the configuration is the same for both packet-switched and circuit-switched data. Where differences exist, they are pointed out on each occasion.

Please note that this chapter only describes a basic setup. Also note that the description is incomplete: some settings are operator-dependent (including all TCP/IP settings such as WINS or DNS entries), and so universally valid settings cannot be given here. Other operator-specific settings may be required which override recommendations given in this chapter.

On completing this chapter you will be ready to connect external devices and establish contact with them in TEMS Investigation. This is covered in chapter 13.

8.2. USB Drivers for PhonesA USB driver is necessary for using the phone as a modem and hence for collecting measurements. The USB driver installation was covered in section 5.5.1.

LZT 108 9985 R1B 41


8.3. Configuring Dial-up Networking (RAS)This section describes how to configure Dial-Up Networking (RAS) in Windows for packet-switched data services.

It is assumed that the phone has been plugged in and recognized by the PC (section 5.5.1).

8.3.1. Dial-up Networking Configuration in Windows Vista

1. From the Control Panel, select Network and Internet.

2. Click “Connect to a network”.

3. Click “Set up a connection or network”.

4. Select “Connect to the Internet”. Click Next.

5. If you are already connected to the Internet, you will be notified of this. Click “Set up a new connection anyway”.

6. Under “How do you want to connect?”, select Dial-up.

7. Under “Which modem do you want to use?”, select the modem of your device:

Note: The dialogs gone through below may differ in some respects between different versions of each operating system. However, the information that needs to be provided is similar in all cases, so the instructions should still be helpful.

Phone Modem to Select

Sony Ericsson phones

“Sony Ericsson <model name> Serial Modem” or “Sony Ericsson [<model name>] USB WMC Data Modem”

Datang phones

Modem used for data traffic. (This modem does not have a distinctive name; you have to know which one it is. Please consult Datang documentation.)

LG phones “LGE <model name> USB WMC Data Modem”

42


8. Under Dial-up phone number, enter the access phone number for the data service. For UMTS this is usually *99#. If the APN (Access Point Name: see section 8.4 below) is not at the top of the APN list but at position n, you must dial *99***n#. For TD-SCDMA, enter *98*1#. For CDMA/EV-DO, enter #777.

9. Fill in your user name and password if required. Leave the boxes Show characters and Remember this password unchecked. Name your dial-up connection.

10. Under “Allow other people to use this connection”, make the selection that is most appropriate in your case.

11. Click Connect. The dial-up connection will now be tested. Click Skip if you want to skip this test. Later, when you are using the command sequence for data service testing, you do not dial up in this way but rather from within TEMS Investigation (see the Data Collection User’s Manual, chapter 14).

12. Back in Control Panel Home, under Network and Internet, click “View network status and tasks”.

13. Click “Manage network connections”.

14. Right-click the dial-up connection you just created and select Properties.

15. Select the Networking tab. Under “This connection uses the following items:”, make sure that “Internet Protocol Version 4 (TCP/IPv4)” is

Motorola UEs “Motorola USB Modem”

Nokia GSM phones

“Nokia <model name> (USB)”

Nokia UEs Three modems “Nokia <model name> (USB) ...” are in the list.

Which you select here should not matter; however, tests have shown that the best performance is achieved by choosing the modem with the middle port number here.

Qualcomm chipset based

“Qualcomm Proprietary USB Modem ...”

Phone Modem to Select

LZT 108 9985 R1B 43


checked, and uncheck “Internet Protocol Version 6 (TCP/IPv6)”. See section 3.17.1. Leave “Client for Microsoft Networks” unchecked.

16. Select “Internet Protocol Version 4 (TCP/IPv4)” and click Properties. Normally an IP address and DNS server address will be assigned to you automatically. If that is not the case for you, enter the proper information and click Advanced. In the dialog that appears, deselect “Use IP header compression” and make sure that “Use default gateway on remote network” is checked. Click OK.

17. The dial-up configuration is now complete. Click OK to exit all dialogs.

8.3.2. Dial-up Networking Configuration in Windows XP

1. From the Start menu, choose Connect To → Show All Connections. The Network Connections dialog appears.

2. Click the underlined link “Create New Connection”. The New Connection Wizard appears. Click Next.

3. Select “Connect to the Internet”. Click Next.

4. Select “Set up my connection manually”. Click Next.

5. Select “Connect using a dial-up modem”. Click Next.

6. Select your modem in the list. For details, see section 8.3.1, step 7. Then click Next.

7. Name the connection. Click Next.

8. In the Phone number field, enter the access phone number for the data service. For UMTS this is usually *99#. If the APN (Access Point Name: see section 8.4 below) is not at the top of the APN list but at position n, you must dial *99***n#. For TD-SCDMA, enter *98*1#. For CDMA/EV-DO, enter #777.

9. Under “Create this connection for:”, make the selection that is most appropriate in your case. Click Next.

10. Fill in your user name and password if required. Uncheck all three checkboxes. Then click Next.

11. Create a shortcut to the desktop if you like, then click Finish.

12. In the Connect... dialog, verify the user name and password. Check the box “Save this user name and password for the following users”. Then click Properties.

44


13. Select the Networking tab. Under “Components checked...”, make sure that “Internet Protocol (TCP/IP)” is checked and selected, and that “Client for Microsoft Networks” is not selected.

14. Select “Internet Protocol (TCP/IP)” and click Properties. Normally an IP address and DNS server address will be assigned to you automatically. If that is not the case for you, enter the proper information and click Advanced. In the dialog that appears, deselect “Use IP header compression” and make sure that “Use default gateway on remote network” is checked. Click OK.

15. Now test the dial-up connection. With the phone plugged in, click Dial in the Connect... dialog. Verify that the connection is established, then disconnect. Later, when you are using the command sequence for data service testing, you do not dial up in this way but rather from within TEMS Investigation (see the Data Collection User’s Manual, chapter 14).

16. The dial-up configuration is now complete.

8.4. Setting Up the APN for the Phone (UMTS, RAS)

To run packet-switched data services in UMTS, you need to configure the Access Point Name (APN) in the phone. This can be done:

• directly in the phone user interface

• by sending an AT command to the phone.

Note that for Datang, the APN configuration has been taken care of in section 5.5.1. If you want to change the APN later on, it is most convenient to run DatangPostInstall.exe again (with argument).

8.4.1. Setup in Phone User InterfaceSome examples are given below.

Sony Ericsson C702, W760i, Z750iIn the phone’s menu system, navigate to Settings → Connectivity tab → Internet settings → Connect using.

LZT 108 9985 R1B 45


Nokia N96In the phone’s menu system, navigate to Tools → Settings → Connection → Destinations.

8.4.2. Setup Using AT Commands

You can send AT commands to the phone from a terminal emulator such as the Windows HyperTerminal.1 Send the AT commands to the virtual port that will be used for data service measurements (see section 8.3.2).

For Nokia phones this method does not work, because the APN setting sent with an AT command is not saved. Do the setup directly in the phone instead, as exemplified in section 8.4.1.

To check what APNs have already been set up, give this command:

AT+CGDCONT?

To set an APN with CID number 1, the command is:

AT+CGDCONT=1,"IP","<APN>"

where <APN> is the Access Point Name, for example

AT+CGDCONT=1,"IP","umts.my_server.com"

Note that with terminals from certain vendors (including Sierra Wireless), “IP” must be written in uppercase letters.

You can check that the APN is correct by sending AT+CGDCONT? once more.

Note: In Windows Vista you must have administrator rights to be able to send AT commands to devices.

1. AT commands can also be sent from within TEMS Investigation, using the Command Sequence tool (Data Collection User’s Manual, section 14.10). This, however, naturally requires that the phone has been connected in TEMS Investigation. See the Data Collection User’s Manual, chapter 6.

46


Alternatively, AT commands can be entered in the Windows modem properties dialog (Control Panel → Phone and Modem Options → Modems tab → Properties → Advanced). The commands are then sent automatically to the phone in each dial-up. This method is of course applicable to phones from any supplier; the disadvantage is that no querying mechanism is available.

8.5. Configuring Devices for NDISThe following TEMS Investigation connectable devices can be configured to use an NDIS data connection:




• Option GlobeTrotter HSUPA

• Qualcomm TD8200

• Sierra Wireless AirCard 880/881

The following TEMS Investigation connectable devices always use an NDIS data connection:

• Ericsson Fixed Wireless Terminals (all supported models, see section 4.1.2)

8.5.1. Configuration of Sony Ericsson PhonesThe configuration is done directly in the phone.

• In the phone’s menu system, navigate to Settings → Connectivity tab → USB → USB network → USB network type → Phone as modem.

• Press Back, then under USB data accounts, select the data account with the correct APN.

To terminate the NDIS connection, set USB network type to Off.

8.5.2. Configuration of Data CardsThe configuration is done using a software application delivered with the data card. For example, for Sierra Wireless data cards, you use an application called 3G Watcher:

LZT 108 9985 R1B 47


• Assign the correct APN to the device.

• Perform the “connect” operation in order to give the device an IP address.

To terminate the NDIS connection, do a “disconnect” in the third-party application.

Please consult documentation from the vendor for further details.

8.5.3. Configuration of Qualcomm TD8200The configuration is done using the application QMI Connection Manager. Please consult Qualcomm documentation for further details.

8.6. Testing Circuit-switched Data Services with UEs

8.6.1. Testing Circuit-switched by Placing Video CallsYou can test data transfer over circuit-switched by running the video telephony application installed in the phone (if the phone has one). Video calls can be controlled by the command sequence function in Data Collection (see the Data Collection User’s Manual, section 14.9).

Please consult documentation from the phone supplier regarding how to operate the video telephony application. No special PC configuration is required for this purpose.

48

Chapter 9. PC and Device Configuration for DRT Scanner

9. PC and Device Configuration for DRT Scanner

This chapter applies to all currently supported DRT scanners (models listed in section 4.1.4).

The DRT scanner can either be connected directly to the PC by means of a cable, or it can be accessed over a local area network. The instructions that follow tell how to configure the PC in each case.

See also the Data Collection User’s Manual, section 6.3.3.

9.1. Direct ConnectionThe DRT scanner is shipped configured for a direct connection and is assigned the static IP address 192.168.5.2. The PC’s Ethernet adapter must likewise have its TCP/IP address configured as static and equal to 192.168.5.1.

Follow these steps:

1. Access the Windows user interface showing your network connections. In Windows Vista, select Start → Settings → Network Connections. In Windows XP, select Start → Connect To → Show All Connections.

2. Double-click Local Area Connection and click the Properties button.

3. In the box below “This connection uses the following items:”, select “Internet Protocol (TCP/IP)” in Windows XP and “Internet Protocol Version 4 (TCP/IPv4)” in Windows Vista. Then click the Properties button.

4. Select “Use the following IP address”. Under IP address, enter 192.168.5.1. Under Subnet mask, enter 255.255.255.0. Then click OK.

5. Connect the scanner to the PC’s Ethernet port with a crossover 100Base-T cable.

LZT 108 9985 R1B 49


9.2. Local Area Network ConnectionFor this setup, the scanner must be reconfigured to acquire a dynamic IP address from the network.

Follow these steps:

1. Assuming the scanning receiver and the laptop are both configured for static IP addressing, and the scanner is connected to the remote PC via a crossover 100Base-T cable, connect to the scanner with a web browser by entering the URL http://drt4301snAAAA, where AAAA is the serial number of the device.

2. On the web page that appears, under Wired Ethernet configuration, clear the Static IP Address field.

3. Click Save Changes.

4. Access the Windows user interface showing your network connections. In Windows Vista, select Start → Settings → Network Connections. In Windows XP, select Start → Connect To → Show All Connections.

5. Double-click Local Area Connection and click the Properties button.

6. In the box below “This connection uses the following items:”, select “Internet Protocol (TCP/IP)” in Windows XP and “Internet Protocol Version 4 (TCP/IPv4)” in Windows Vista. Then click the Properties button.

7. Select “Obtain an IP address automatically”.

8. Select “Obtain DNS server address automatically”. Then click OK.

9. Connect the PC and the scanner to available Ethernet ports on the same subnet of the LAN with normal (non-crossover) 100Base-T cables. If the remote location is not on the same subnet, then a VPN connection may be used to create an extended virtual subnet that can host the scanner as if it were on a local subnet.

9.3. Verifying the ConfigurationHere is how to confirm and troubleshoot the connection to the scanner.

Before you begin, make sure your firewall is disabled; see sections 3.11 and 3.14.

1. Connect the Ethernet cable or cables as described in sections 9.1 and 9.2.

50

Chapter 9. PC and Device Configuration for DRT Scanner

2. Open a Windows command prompt (select Start → Run, enter cmd and press Enter).

3. Ping the unit by typing the command ping DRT4301SNAAAA, where AAAA is the serial number of the device, and observe if responses are received.

4. If no response occurs, you may use Wireshark to capture the Ethernet traffic and determine the unit’s current IP address. Enter the filter term nbns.flags == 0x2910 to isolate the Netbios Naming Service registration messages sent out by the scanner. The IP address will be included in the message from the scanner.

9.4. Scanner Antenna ConnectionThe RF antenna must be connected to the RF IN B port on DRT scanners that have two RF inputs.

LZT 108 9985 R1B 51


10. PC and Device Configuration for Ericsson Fixed Wireless Terminal

Ericsson Fixed Wireless Terminals (FWTs) are routers offering wireless access to broadband Internet and telephony. The FWT constitutes a gateway to a network.

Regarding FWT operation in general, please consult the documentation delivered with the product.

10.1. PC ConfigurationIf an FWT is to be used with TEMS Investigation, the following must be observed:

• The PC must not be connected to any other network. (The “default gateway” must be unambiguously defined in the PC OS.)

• The default IP address of the FWT is 192.168.1.1. It is possible to change this address to any value; however, TEMS Investigation requires that the IP address fall within the private address space (see IETF RFC 1918).

• If a firewall or other security product is installed, you must make sure that port 1895 is open, since the TEMS service uses this port.

10.2. FWT ConfigurationThe FWT itself must be configured as follows:

• Connect the PC and FWT with a LAN cable.

• Configure the network interface on the PC with either a static IP address in the range 192.168.1.0/241 or DHCP.

• Using Telnet2, log in to the FWT (192.168.1.1)1 as root. The root password will be different in each custom configuration. Please contact your supplier or operator for assistance.

52

Chapter 10. PC and Device Configuration for Ericsson Fixed Wireless Terminal

• Run the following commands:

# cf set tems.enabled true

# cf commit

The TEMS service will now always be running on the FWT whenever it is turned on. There is no need to restart the TEMS service after the FWT has been rebooted.

To disable the TEMS service, run these commands:

# cf set tems.enabled false

# cf commit

1. This is the default network on the FWT LAN, though it is possible that the FWT has been configured differently.

2. In Windows Vista, the Telnet client is by default not activated. To activate it, do as follows: Open the Control Panel and navigate to Programs and Features. Click “Turn Windows features on or off”. In the feature list that appears, check Telnet Client.

LZT 108 9985 R1B 53


11. Configuring the PC for Python Script Processing

To be able to run Python scripts from a Windows command prompt, you must do the following (requires administrator rights on the PC):

• Create a new environment variable (user variable) PYTHONPATH and set it to

<TEMS Investigation install dir>\Scripts;<TEMS Investigation install dir>\Application

where by default <TEMS Investigation install dir> = C:\Program Files\Ascom\TEMS Products\TEMS Investigation.

If you are using a different installation directory, or if you put your Python scripts in a different location, then you need to modify the contents of PYTHONPATH accordingly.

• To the environment variable (system variable) PATH, add the path to the Python installation, for example C:\Python25.

For details on how to set up environment variables, please consult your Windows documentation or the following web pages:

• Windows XP: support.microsoft.com/kb/310519

• Windows Vista: The instruction for Windows XP can be followed with some minor adjustments. In step 2, click Advanced system settings.

Note again that PYTHONPATH must be a user variable, not a system variable.

54

http://support.microsoft.com/kb/310519

Chapter 12. Cell Data and Maps

12. Cell Data and Maps

Two aspects of the presentation (in both Data Collection and Route Analysis) require some preparation:

• Presenting cell data

• Displaying background maps

These things are not addressed here but in the User’s Manuals.

• How to load cell files is described in

– Data Collection User’s Manual, section 5.3

– Route Analysis User’s Manual, section 5.2

• How to load map files is the subject of

– Data Collection User’s Manual, sections 25.3–25.4

– Route Analysis User’s Manual, section 5.1

LZT 108 9985 R1B 55


13. Connecting External Equipment

See the Data Collection User’s Manual, chapter 6.

56

Chapter 14. Support Contact Information

14. Support Contact Information

For support in using TEMS Investigation, please contact Ascom according to the directions found at

www.tems.com

under the link “TEMS Sales & Support”.

To sign up for the TEMS on-line subscription service, please go to the same web site and, under the heading “TEMS Subscriptions”, click the link “Register for TEMS Subscription Services”. This free service includes e-mail notification of TEMS product launches, version upgrades and patches, as well as the on-line newsletter TEMS News.

LZT 108 9985 R1B 57



58

Index

Index

Symbols.NET Framework 29

AAccess Point Name (APN) 45accessories 8administrator rights on PC, actions requiring 9Aero Glass 13Analysis Packages 6Anritsu scanners 24

basic configuration of ML8720 model 24cable to use with ML8720 model 25supported models 18USB driver for ML8740/8741 models 35

APM (Advanced Power Management) 10APN (Access Point Name) 45AQM

licensing for 7phones supporting 22

AQM modules 17drivers for 36

audio quality measurements (AQM)phones supporting 22

automatic updating of software 10AutoPlay 10

Bbackpack (TEMS Indoor Backpack) 35Base Packages 5Bluetooth 10

Ccables to use with phones

Sony Ericsson Z750i 23Call Generator 30

installing 38

LZT 108 9985 R1B 59


cell data, importing 55circuit-switched data services, testing with UEs 48connectable phones and data cards, list of

CDMA 17TD-SCDMA 17UMTS 15

connectable scanners, list ofCDMA 20UMTS 18

contents of Getting Started Manual 1

DData Collection User’s Manual 1data service testing

configuring PC and phones for 41data services 4Datang LC8130E 17Datang phones

Dial-up Networking configuration for 42USB drivers for 32

Datang PostInstall utility 32, 45definitions of TEMS Investigation concepts 3Dial-up Networking, configuring 42

in Windows Vista 42in Windows XP 44

Documents folder 10DRT4301A+ scanners 19, 20, 26

configuration of 49configuring for local area network connection 50connecting RF antenna to 51

Eenergy saving features in Windows 12equipment cases 2Ericsson Fixed Wireless Terminals 17

configuration of 52PC configuration for 52

external antennasconnecting to phones 24support for in phones 22

external equipment 15connecting in TEMS Investigation 56

60

Index

FFAQ (on TEMS website) 3firewall in Windows 12

GGPS protocols, supported 20GPS units

list of supported 20USB driver for 35

Hhardware key, driver for 40hardware requirements for installing TEMS Investigation 27HASP HL SRM 31HASP HL SRM Key Reader utility 30, 40HASP SRM Remote Update utility 30

IIEEE 802.11 (WLAN) 14indoor backpack 8, 25Information Elements and Events 1installing license software 31installing TEMS Investigation 27, 30Internet Explorer 29IPv6 13IR port 11

LLG CU320 15LG CU500 15LG phones

Dial-up Networking configuration for 42LG U960 16licensing in TEMS Investigation 39

floating license 8, 39for AQM 7for Data Collection 40for external devices 7for Route Analysis 39local license 39network license 8, 39

MManual UE Configuration utility 30, 33, 34maps, importing 55

LZT 108 9985 R1B 61


Microsoft Core XML Services 29Microsoft DirectX 29Motorola E1000 16Motorola E1070 16Motorola M2501 16Motorola Razr Maxx V6 16Motorola Razr V3x 16Motorola Razr V3xx 16Motorola Razr2 V9 16Motorola UEs

Dial-up Networking configuration for 43USB driver for 34

MSXML 29My Documents folder 10

NNDIS data connection

configuring devices for 47devices capable of using 47

Nokia 6086 16Nokia 6120 16Nokia 6121 16Nokia 6125 16Nokia 6230i 17Nokia 6280 16Nokia 6680 16Nokia 7376 16Nokia GSM phones

Dial-up Networking configuration for 43Net Monitor function 23USB driver for 34

Nokia N75 16Nokia N80 16Nokia N95 16Nokia N96 15

general capabilities of (EU version) 22general capabilities of (US version) 22GSM capabilities of 22using external antenna with 24

Nokia PC Suite 11Nokia UEs

Dial-up Networking configuration for 43Net Monitor function 23

62

Index

USB driver for 34

Ooperating system requirements for installing TEMS Investigation 29Option GlobeTrotter Express HSUPA

general capabilities of 22GSM capabilities of 22

PPC configuration

for Data Collection 9for DRT scanner 49for Ericsson Fixed Wireless Terminal 52for Python script processing 54

PCTel SeeGull EX scanners 25supported models (CDMA) 20supported models (LTE) 19supported models (UMTS) 18USB driver for 35

PCTel SeeGull LX scanners 25supported models (CDMA) 20supported models (UMTS) 18, 19USB driver for LX MM2 34

phones 3basic configuration of 23capabilities of phones sold with TEMS Investigation 22list of connectable (CDMA) 17list of connectable (TD-SCDMA) 17list of connectable (UMTS) 15

port-scanning software 11power management in Windows 12product packaging 5Python

configuring PC for 54required software 29

QQualcomm chipset based devices

connectable (CDMA) 17connectable (UMTS) 16Dial-up Networking configuration for 43enabling diagnostics reporting 23USB driver for 34

LZT 108 9985 R1B 63


RRAN Tuning

software requirements 29Readme file 3Release Note 3Replay Packages 6Route Analysis User’s Manual 1RTP ports for video streaming 11

Sscanners 4

list of connectable (CDMA) 20list of connectable (UMTS) 18

screen savers 12security products 11sleep mode in Windows 12software requirements for installing TEMS Investigation 29Sony Ericsson C702 15, 19

cable to use with 23Sony Ericsson C905 15, 18

cable to use with 23configuring USB speed 23general capabilities of 22GSM capabilities of 22

Sony Ericsson C905a 15, 18cable to use with 23configuring USB speed 23general capabilities of 22GSM capabilities of 22

Sony Ericsson K600i 15Sony Ericsson K790a 16Sony Ericsson K790i 17Sony Ericsson PC Suite 11Sony Ericsson phones

Dial-up Networking configuration for 42USB drivers for 32

Sony Ericsson TM506 15cable to use with 23

Sony Ericsson W600i 17Sony Ericsson W760i 15, 19

cable to use with 23Sony Ericsson Z750i 15, 18

cable to use with 23

64

Index

general capabilities of 22GSM capabilities of 22using external antenna with 24

SpeedStep technology 11support contact information 3, 57

TTC-1450 equipment case 25TC-1520 equipment case 25, 35TC-1520B equipment case 25, 35TEMS Indoor Backpack 35TEMS on-line subscription service 3TEMS Pocket 2TEMS Pocket Positioning Tool 31terminals 3

UUDP ports for video streaming 11uninstalling TEMS Investigation 37USB drivers for phones 32USB Legacy Support 12USB-to-RS232 serial converter in equipment cases and backpack, driver for

35user terminals 3

Vvideo streaming, RTP (UDP) ports for 11video telephony

using for circuit-switched data testing 48virtual memory requirements for installing TEMS Investigation 28visual effects

in Windows Vista 13in Windows XP 14

WWiMAX

configuring PC for DRT scanner 49Windows Aero color scheme 13Windows firewall 12Windows Media Player 12Windows Vista settings 13Windows XP settings 14WLAN 14

LZT 108 9985 R1B 65

TEMS™ Optimization Solutions – the number one choice for operators

worldwide. For every stage of a wireless network’s life cycle and supporting

all major technologies, the TEMS portfolio helps operators maximize their

Quality of Service and get the most out of their network investment.

The experience and technological leadership of TEMS gives network

operators the strong partnership they need and a commitment to quality,

accuracy, and success.

TEMS Optimization Solutions – Making Wireless Better.