17
TENDER DOCUMENT FOR PROCUREMENT UNDER MHRD SCHEME OF UPGRADATION OF EXISTING POLYTECHNICS DEPARTMENT: CIVIL ENGINEERING S. No Laboratory Name Of Equipment with Specification Make & Model Rate to be Quoted 1 CONCRETE TECHNOLOGY Universal Testing Machine :_ Computerized 600 KN least count 0.05KN. Load accuracy + 0.5% with PC and software with standard accessories for tensile, compressive & transverse testing. Complete with manual. The Installation, Commissioning and Training should be included in the offer. 2 Vee Bee Consistometer :- as per IS119 consisting of vibrating table 380mm long and 260mm wide. Resting upon elastic support at a height of about 305mm above the floor Complete with start/stop switch, cord and plug. A holder is fixed to the base into which a swivel arm is telescoped with funnel and guide sleeve. The swivel arm is also detachable from the vibrating table. A graduated rod is fixed on a swivel arm and at its end a plastic disc is screwed. The divisions of scale on the rod record the slump of the rod record the slump of the concrete in millimeters. Supplied complete with a sheet metal container with lifting handles which can easily be fixed to the vibrating table. A slump cone open at both ends with lifting handles and a tamping rod of size 16mm dia and 600mm long, rounded at one end. 3 Standard Concrete Cube Moulds:- 150x150x150 size.(Heavy Duty) 4 Vibrating Table: 60cm x 60cm 5 Aggregate Impact Tester:- as per IS 2386 part IV. Quick release mechanism to ensure effective fall of hammer during test. The free fall can be adjusted .380mm. The hammer should be provided with lockage arrangement. Fitted with mechanical counter. Complete with manual 6 Aggregate Crushing Value Apparatus: As per IS 2386 part iv complete with manual. 7 Standard Sieve Set for coarse aggregate as per IS standard 30cm dia made of G.I frame with joint I.S meshes complete set with lid. 8 Digital Balance 5Kg, 10 Kg, 15 Kg (Platform Type) capacity sensitivity 1gm, 1 no each 9 Physical Balance with weights 10 Steel trolley (heavy duty) for carrying load upto 500 kgs 1 TRANSPORTATIO N ENGG. Penetrometer Apparatus: as per IP 49, 50 & 167 specification and also per IS 1448 (P:92) & (P:93) for penetration test of wide variety of materials like, bitumen, greases, wax, polish etc. Complete with electronic trimmer & electric arrangement with brass cone and needle complete with manual. 2 Ductility Testing Machine:- as per IS 1208 consisting of thermostatically controlled bath with inlet and outlet tap complete with moulds and plates, Thermometer etc and manual. 3 Centrifuge Extractor:- as per ASTMD-2172, AASHO T-58, T-64, T-164 for determination of Bitumen %age in bituminous mixture electrically operated.

TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

  • Upload
    lydat

  • View
    232

  • Download
    6

Embed Size (px)

Citation preview

Page 1: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

TENDER DOCUMENT FOR PROCUREMENT UNDER MHRD SCHEME OF UPGRADATION OF

EXISTING POLYTECHNICS

DEPARTMENT: CIVIL ENGINEERING

S.

No

Laboratory Name Of Equipment with Specification Make &

Model

Rate to be

Quoted

1 CONCRETE TECHNOLOGY

Universal Testing Machine :_ Computerized 600 KN least count 0.05KN. Load accuracy + 0.5% with PC and software with standard accessories for tensile, compressive & transverse testing. Complete with manual. The Installation, Commissioning and Training should be included in the offer.

2 Vee Bee Consistometer :- as per IS119 consisting of vibrating table 380mm long and 260mm wide. Resting upon elastic support at a height of about 305mm above the floor Complete with start/stop switch, cord and plug. A holder is fixed to the base into which a swivel arm is telescoped with funnel and guide sleeve. The swivel arm is also detachable from the vibrating table. A graduated rod is fixed on a swivel arm and at its end a plastic disc is screwed. The divisions of scale on the rod record the slump of the rod record the slump of the concrete in millimeters. Supplied complete with a sheet metal container with lifting handles which can easily be fixed to the vibrating table. A slump cone open at both ends with lifting handles and a tamping rod of size 16mm dia and 600mm long, rounded at one end.

3 Standard Concrete Cube Moulds:- 150x150x150 size.(Heavy Duty)

4 Vibrating Table: 60cm x 60cm

5 Aggregate Impact Tester:- as per IS 2386 part IV. Quick release mechanism to ensure effective fall of hammer during test. The free fall can be adjusted .380mm. The hammer should be provided with lockage arrangement. Fitted with mechanical counter. Complete with manual

6 Aggregate Crushing Value Apparatus: As per IS 2386 part iv complete with manual.

7 Standard Sieve Set for coarse aggregate as per IS standard 30cm dia made of G.I frame with joint I.S meshes complete set with lid.

8 Digital Balance 5Kg, 10 Kg, 15 Kg (Platform Type) capacity sensitivity 1gm, 1 no each

9 Physical Balance with weights

10 Steel trolley (heavy duty) for carrying load upto 500 kgs

1 TRANSPORTATIO

N ENGG. Penetrometer Apparatus: as per IP 49, 50 & 167 specification and also per IS 1448 (P:92) & (P:93) for penetration test of wide variety of materials like, bitumen, greases, wax, polish etc. Complete with electronic trimmer & electric arrangement with brass cone and needle complete with manual.

2 Ductility Testing Machine:- as per IS 1208 consisting of thermostatically controlled bath with inlet and outlet tap complete with moulds and plates, Thermometer etc and manual.

3 Centrifuge Extractor:- as per ASTMD-2172, AASHO T-58, T-64, T-164 for determination of Bitumen %age in bituminous mixture electrically operated.

Page 2: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

4 Softening Point Apparatus:- according to IP58 & IS 1205-1958 with F.H.P electrical motor driver, Stimer and electric heater with transporates regulator control

1 SOIL MECHANICS Direct Shear Apparatus:- as per IS 2720 electrically cum manually operated haring 12 contant rates of strain 1.25, 0.625, 0.25, 0.125, 0.05, 0.025, 0.01, 0.005, 0.002, 0.001, 0.0004 & 0.0002mm minote

2 Unconfined Compression Test Machine: Electrically cum hand operated as per IS 2720 part x consists of lead frame, proving ring of capacity 5 KN and 50KN and two dial gauges, three rate of travel 1.25mm, 1.5mm & 2.5mm. Set of plain platen and conical platen to test specimen size 38mm, 50mm, 75mm & 100mm

3 Standard Penetration Test Apparatus:-As per IS 2113 (SPT) to conduct STP & estimate value of “N” with i) Split spoon sampler. ii) Extension rod with coupling (A rods) 5ft long heavy duty. iii) 65kg driver wt with penetration guide assembly with 75cm fall designed. iv) Tripod 18‟ with high and sleeve. v) Spanners (set of two) vi) Avger 6” dia with extension rods for bores. vii) 50.8mm 60 threaded cone for dynamic cone penetration. viii) Casing pipe. ix) Guide pipe assembly. x) Pulley.

4 Vane Shear Test :- Laboratory purpose as per IS 270 part xxx electrically operator rates of rotation 1/60 rpm simple phase complete with manual.

5 Consolidation Apparatus:- For single sample complete with 2 no dial gauges and consolidation ring as per IS specifications

6 Falling Head Permeability Apparatus: for determination permeability studies of soil with over head tank and mould As per IS 2720 part xvii complete with manual.

1 SURVEYING Automatic Level. Specifications: Magnification 32x, Standard deviation per km (double run level)= 2.0mm Accessories: Stand: Aluminium (heavy duty)-1no Staff: Aluminium (4m folding)-1no

2 Electronic Theodolite (including all standard accessories) Specification: Telescope: Image erect, magnification 30x, effective aperture 45mm resolving power 3‟, field of view 1 30‟ Minimum focusing distance = 1.5m Measurement = Minimum reading 1” Display : LCD screen, both sides Level: vertical till compensation range = 3‟ with setting accuracy 1” Accessories: Diagonal eyepiece, adoptor, toolkit, battery holder, handlany case Almunium heavy duty stand.

3 Digital Theodolite: Specification: 2” angle accuracy, 30 x telescope, clear aperature 45mm two faced LCD display.Till compensation automatically, range o compensator + 3‟ nickel hydrogen chargeable battery. Accessories: all standard accessories included complete with manual and training of staff.

4 Ranging Rod:- Steel Rods 10 „ height

Page 3: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

5 Total Station: Specification: 2mm = 2ppm high distance accuracy, 2” angle accuracy, dual-axis compensation (range = 4‟) 10hrs battery backup High productivity with alpha numeric keyboard. Internal memory not less than 10,000 points. Accessories: Heavy duty aluminium tripod 2 no Prism polygon-2no with prism poles Prism 2no Software (Data down loaden) Data case and toolkit.

6 Prismatic Compass :- 4” Prismatic Compass with brass tripod

7 Plane Table complete with all standard accessories. Specification: Plane Table Board: 600 x 750 x 16mm Plane table stand: Aluminium, heavy duty Plane table head: 151 specification ball and socket type. Magnetic compass: 150mm brass Spirit level: 150mm brass Alidade : telescopic ( ISI standard) Pancake coils single layer: brass Plumb bob : brass Canvas cover: Full

1 FLUID MECHANICS

Pipe Friction Apparatus: (Closed circuit) This apparatus is used to measure Darcy‟s coefficient “f” for given pipes.

2 Bernoulli’s Theorem Apparatus:- (Closed circuit) This apparatus is used to verify Bernoullis Theorem

3 Notch tank Apparatus:- (Closed circuit) The apparatus should measure coelf of discharge of various shape, v-notch of angle 60, rectangular Notch 100 x 150mm

4 Venturimeter /orifice apparatus: Use to determine the discharge of water in pipe

5 Discharge measuring apparatus through orifice meter

6 Apparatus for conducting orifice coefficients(cd, Cc & cv): The apparatus is used to measure coefficient of contraction coefficient of discharge and coefficient of velocity of different type of orifices.

7 Hydraulic Bench : Complete with tank and AC motor for circulation of water. Complete with accessories.

8 Simple Manometer for pressure measurement

9 Differential Manometer for measurement of pressure difference.

10 Meta Centric Height Apparatus: Apparatus is used to determine the meta centric height of a ship model under load and unload condition. (Flat bollomed versel).

1 ENVIRONMENTAL ENGG.

Digital PH Meter:- 3 ½ digit LCD, 0 to 14ph accuracy Io.1 ph. Manual lamp compensation 0-100c, IV DC battery electrode stand supplied with combined electrode, doffer solution, electrode stand.

2 P H Meter Pen Type:- 0-14ph, accuracy I 0.2 ph. Temperature 3 ½ digit LED display.

Page 4: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

3 ENVIRONMENTAL ENGG.

Floculator:- With illuminated base having florescent tube fitted below fluorescent plastic plate. Consists of geared 1/20 HP variable speed from 10 to 100 RMP with speed control. Fitted with SS stirring rods, electrically operated suitable to work on 220v. With 4 stainless cap 1 lt/ 2lt Digital RPM indicator for above

4 Dissolved Oxygen Meter:- (Portable) 3 ½ digit LCD displays (CWM)

5 Portable Digital TDS Meter: Display 3 ½ LED 0 – 1999ppm, 0 to 19.99ppt Acc 2 % FS IV DC battery operated. Supplied with conductivity cell housed in ABS cabinet. Complete with manual.

6 Residual Chlorine Meter as per Indian Standards

7 Digital conductivity meter (Portable):- 3 ½ digit LCD display 0 to 1999 ms, 0 to 19.99 ms Accuracy 1% in ABS plastic cabinet with touch switches battery operator

8 Water Meter : as per Indian Standards

9 Pipe Fittings consisting of Valves of different types, unions, nipples, bends etc

10 Dye for threading of GI / Plastic / CI Pipes

11 Pipe Samples og Plastic / GI / CI / Concrete / Asbestos / Stoneware

Page 5: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

TENDER DOCUMENT FOR PROCUREMENT UNDER MHRD SCHEME OF UPGRADATION OF

EXISTING POLYTECHNICS

DEPARTMENT : ELECTRICAL ENGINEERING

S.

N

o

Laboratory

Name Of Equipment with Specification Make &

Model

Rate to be

Quoted

1. Electrical Machine Lab

D.C shunt motor coupled with D.C Shunt generator 3hp

motor ,5kw 1500rpm Generator including Control Pannel Board

2 D.C series motor coupled with D.C Series generator 3.5 KW,230 V,1500 rpm DC Series Motor Coupled with 3KW,230V,1500 rpm DC series Generator including Control Pannel Board. 1

3 D.C Compound motor coupled with D.C Compound DC

generator 5 H.P.,220V DC,1500 rpm DC Shunt Motor

Coupled with 3KW, 220V

DC,1500 rpm DC Shunt Generator including Control Pannel

Board

4 Three phase induction motor 7H.P,,440V,50 Hz,1500 rpm.Squirrel Cage Induction Motor having all Terminal on Terminal Box with Star/Delta Starter, Belt & Pully loading arrangement including Control Pannel Board

5 3 Phase Slip Ring Induction motor 7H.P,,440V,50 Hz,1500 rpm.Slipring Induction Motor (with Rotor Resistance/DOL Starter) including Control Pannel Board and its loading Arrangement.

7 3 phase Alternator coupled with dc shunt Motor

5kw coupled with 7 hp shunt motor including panel board and all accesories

8 Auto Synchronous motor 5KVA

5kva with excitor

9 1 Phase universal Motor 2hp including panel board and all accesories

10 1 Phase Capacitor start Capacitor run motor 2 KV

2hp Capacitor Start- Capacitor run Single Phase Indution

Motor having all

Terminal on Terminal Box , with loading arrangement

including Control Pannel Board.

11 1 Phase split phase Motor 2hp including panel board and all accesories

12 Motor Generator Set (3 Line Type) – 30 KW including panel board and accessories

Page 6: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

13 Electrical Machine Lab

Synchronization of alternator Lamp Method including panel board and all accessories

14 Parallel operation of 3 phase transformer each capacity 10 KVA */Delta connections including panel board and all accessories

15 Potential Transformer 11 KV/ 110 V

16 Induction Motor 7 HP Speed control using pole charging method including panel board and all accessories

17 Transformer for conducting OC/SC test 5kva including wattmeter , ammeter, voltmeter(ac) including panel board and all accesories

1 Power Electronics

CRO 100 MHz Digital

2 Kits for Ohms Law, Kirchoff Law, Series and Parallel Resistances, Nortans Theorem, Thevenins Theorem, Maximum Power Transfer theorem, Reciprocity Theorem and Superposition Theorem

3 Synchronous cope 3 phase digital type Synchronous cope with all accesories

4 Multi media Projector

Projection System: Epson 3LCD, 3-chip technology

Projection Method: Front / rear / ceiling mount

Driving Method: Epson Poly-silicon TFT Active Matrix

Pixel Number: 480,000 dots (800 x 600) x 3

White Light Output: 2500 lumens1 (ISO 21118 Standard)

Color Light Output: 2500 lumens1

Aspect Ratio: 4:3

Native Resolution: 800 x 600 (SVGA)

Resize: 640 x 480 (VGA), 1024 x 768 (XGA), 1152 x 864 (SXGA),

1280 x 800 (WXGA), 1440 x 900 (WSXGA), 1400 x 1050 (SXGA+)

Lamp Type: E-TORL™ 200 W UHE

Throw Ratio Range: 1.45 – 1.96

Size (projected distance): 23" – 350" (0.87 – 10.5 m)

Keystone Correction: Manual: Vertical: ±30 degrees

USB Plug 'n Play: Projector is Mac® compatible via DVI to HDMI

or VGA adapter (not included)

Contrast Ratio: Up to 2000:1

Color Reproduction: 16.77 million colors

1 PLC Lab Computer Latest configurations

2.4GHz Core i7 2760QM processor 8GB, 1,333MHz DDR3 1TB, 5,400rpm Intel HM65 AMD Radeon HD 7690M Windows 7 Home Premium 380 x 244mm 28.3mm 15 inches (1,920 x 1,080)- TFT 2.63kg Mainstream with keyboard & Mouse

2 Servo Stabilizer 10 KVA

3 phase 10 KVA un balanced type

Page 7: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

3 PLC Lab PLC Trainer

System Specifications: v PLC MAKE: ALLEN-BRADLEY MICRO 800 SERIES 2080-LC10-12AWA/ STD. EQUIVALENT. v Micro810 Controller, 8IN 120/240VAC, 4RLY, AC PWR v 8 Digital input / 4 Digital outputs. v 24VDC, 1.5A Power source.4”X2”X2”. v I/p- O/p LED indication on front panel. v PC interface facility. PC-PLC interfacing cable. v 2080-USBADAPTER: USB Adapter Plug for Micro810 12-pt only v 2080-LCD: 1.5 LCD Display and Keypad, for Micro810 Only v Necessary I/p-O/p simulating devices. v Ladder diagram programming on PC. v SCADA SOFTWARE connectivity for PLC.(optional) v Electrical control panel for simulation of digital .

1 Electrical Workshop

Coil Winding Machine

Standard Machine Specifications Base Plate Size 15" x 14" in inches Maximum Coil/Bobbin Diameter 8" in inches Maximum Centre Distance 5" in inches Maximum Axial Winding Length 4.5" in inches Wire Range 20-46 / 16-40 / 14 36 swg Choose any one of the following wire range No of Bearings 12 Main Gears Steel (Big) - Nylon (Small) Nylon gear is used for noise reduction Traverse Shifting Manual Traverse Type V-Bed Rod bed can be used for better winding of thinner gauge at additional cost Tensioner Standard Optional: Regular Tensioner can be used for wire gauge 28-40swg at additional cost Spool Carrier up to 5Kgs Approx Weight 35Kgs of the machine Additional Optional Accessories Motor 1/2 HP 1440rpm Single or Three Phase Marshall Make Clutch Foot Paddle Assembly Fabricated stand

2 1 Phase energy meter (induction type) Induction type 40A

3 1 Phase energy meter (digital type) Digital type 40A

4. 1 Phase energy meter (electronic type) Electronic type 40A

Page 8: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

TENDER DOCUMENT FOR PROCUREMENT UNDER MHRD SCHEME OF UPGRADATION OF

EXISTING POLYTECHNICS

DEPARTMENT : MECHANICAL ENGINEERING

S.

No

Laboratory Name Of Equipment with Specification Make &

Model

Rate to be

Quoted

1 Strength Of Materials Lab

UNIVERSAL IMPACT TESTING MACHINE Working on Pendulum principle for Izod and Charpy test. Capacity: 30 kgf +/- 0.15 kgf, should be as per IS- 1499-1959. IS 1598, 1757

2 ROCKWELL HARDNESS Model twin, manual load with automatic zero setting dial gauge for conducting test with initial load of 50,100,150 kgf, should be supplied with A,B,C indentors. Supplied with diamond indentor120 deg cone angle( 3 Nos.), ball identor with 1/16 inch steel ball indentor with 5 additional balls, two allan spanners, one bottle of dash pot oil, clamp device.

3 ULTRASONIC FLAW DETECTOR. The apparatus is used to detect flaws of various types in metals and concretes by using different probes.A Scan pulse echo typeThe equipment shall be capable of storing calibration data as well as screen pattern,suitable port for down loading the complete data set to personal computer.The equipment shall be capable of operating in mains cum battery , when operating with mains ,the voltage should be 230+-10v, 50Hz. Test mode:capable for working in pulse echo and transmit-reciever mode. Frequency mode:one broad band amplifier in the frequency range from 1MHz to 6MHz. Test range: 50mm. or less to 5 meter range, the range should be adjustable in 2mm steps or less. Trace delay:facility of minimum 3 meter length in steel in steps of 2mm or less. 120dB total gain, operable gain of 80dB in minimum 0.5dB or higher. Memory provision for storing and recalling.

4 SPRING TESTING MACHINE. Electronic type , 1-100gms Displacement-: 50-200mm 5accuracy +/- 0.5mm Temperature 5-50 deg C Seven segment display. 30mm LCD

1. Material Science METALLURGICAL TRINOCULAR MICROSCOPE: Objective: 5 X, 10X,20X, 40X. Eye piece: 10X/ 22mm Nosepiece: Quadruple. Stage moving range: 250 mm × 250 mm coaxial coarse & fine focus adjustment system Illumination: Halogens lamp 6v20 V,adjustable brightness. Digital camera standard port.

Page 9: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

2 Material Science ABRASIVE CUT OFF MACHINE: The rating is 2H.P provided with abrasive, grinding wheels capable of cutting different metals of various diameters. Table top direct cutting model ( Aluminium base) Motor capacity : 1 H.P, single phase

Single illumination

TWIN Cam operated vice

Cutting Size : 40mm max.

Wheel Size : 8”

Front hood with large window

Side opening for length specimen

Coolant Jet

Recirculating Coolant Chamber, Capacity : 30 litres

3 POLISHING MACHINES: Disc Size : 200mm Variable Speed 50-800 rpm No.of Disc: 1 No.of Motor: 1 Water flow: single

1 Refrigeration And Air Conditioning Lab

COMPLETE REFRIGERATION AND A.C TOOL KIT.

Pipe cutters

Pipe flaring tools

Set off spanner screw drivers

Nuts, unions, reducers of various sizes.

Service valve gauges, compound gauges.

Leak detectors.

Blow lamps.

Tool accessories and other items such as Tube cutter, Spring bender lever, Mech. Bender, flaring tool, flaring block, flaring yoke, swaging tools, set off tools of different types of wrenches, pliers, screw drivers (including star screw driver), gold switch hacksaw and blades, vice, reamers, smooth files, tongs, test shut off valves, service gauges, compound gauge, charging hoses, blow lamp, soldering and brazing units, nitrogen cylinder,R-12 and R-12 cylinder of 2 kg and 5 kg. Insulating materials, pipe wrench, L end key, set blow lamp.

2 REFRIGERATION TEST RIG WITH COMPUTERISED CONTROL AND INSTRUMENTATION: Compressor : Hermetically sealed compressor. Condenser : Air Cooled condenser made out of copper pipe & Aluminum fins of matching capacity with fan cooling. Evaporator : Copper Coil immersed in water. Expansion device : Capillary Tube & Thermostatic expansion valve. Energy Meter : One each for power measurement of compressor & evaporator heater. Pressure Gauge : 2 Nos. for H.P., L.P. measurement. Suitable filter/drier. Hand Shut Off type Service valve. Dimmerstat to control power supply to heater. Rotameter for Refrigerant flow measurement. Immersion type electric heater. Solenoid valve. Set of thermocouples. 12 Channel Digital Temperature Indicator. HP-LP Cutout. Switches : For

Page 10: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

compressor, condenser fan, solenoid valve & evaporator heater. Voltmeter : 0 - 250 V. Ammeter : 0 - 15 A Thermostat. The plant should have design of simple and functional concepts able to visuals the main components of a compression refrigeration cycle.

3 Material Science SAMPLES OF ALL VALVES USED IN REF. AND AIRCONDITIONING: Safety controls: High pressure and low pressure cut outs, oil pressure controls, solenoid valves, automatic expansion valves, thermostatic expansion valves, thermostat for low temperatures, thermostat for medium temperatures and thermostat of high temperatures.

1 Refrigeration And Air Conditioning Lab

TOOL MAKER MICROSCOPE Magnification 30 x (Standard)

Eye Piece Protactor

Graduation 1 ° rotation 360° with adjustable vernier of 2 minutes.

Observation Tube

Monocular inclined at 45° with reticle of cross line.

Micro Work Stage

Highly accurate linear cross rollers guided micro work stage Size 150 x 150 mm with least count 0.001 mm.

Travel of Stage 50 x 50 mm on X and Y Axis by micrometer 0 to 25 mm L.C. 0.001 mm.

Illumination 6 V - 20 W halogen light with highly precise condensing System built in Green Filter.

Work Distance 67 mm.

Maximum Work Height

90 mm.

Maximum Weightcapacity

10 Kg.

Field of View 6.5 mm.

STANDARD ACCESSORIES

Ply Wood Box, Projection Lamp 2 Nos., Calibration Certificate, Operating Manual.

Optional Accessory

V-Block/ Center Holding device/ Digital Read out with different options / Rotary Table / Projection Lamps

2 ELECTRONIC COMPARATOR: Comparator having range 170mm, fine adjustment for quick zero setting, plane base.Base/Measuring anvil should be flat within 0.001mm. Anvil faces to be parallel to datum surface within 0.005mm. Stem dia. Straight within 0.005mm. Fitted with electronic probe and analog gauge unit having 5 metric ranges and tolerance lamps.

Page 11: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

TENDER DOCUMENT FOR PROCUREMENT UNDER MHRD SCHEME OF UPGRADATION OF

EXISTING POLYTECHNICS

DEPARTMENT : AUTOMOBILE ENGINEERING

S.

No

Laboratory Name Of Equipment with Specification Make &

Model

Rate to be

Quoted

1 Automobile Workshop

Brake Dynamometer: 2WD/8.575” Rolls-120mph, 405hp road load OR 4WD/AWD-150 Hybride series 8.525” rolls-150 mph-2000hp 625-hp peak absorption.

2 Electric Operated Spray Paint Gun: Volt: 120v Amp: 1 Gallons/hr: 5.1 Power cord length: 7ft 10 inch capacity: 33oz cup.

3 Tachometer for MPF1 Engines: OBD Tachometer 9620 global OBD II Scan tool.

4 Portable Type Hydraulic Jack: Lifting capacity: 2500kg Electric motor power rating: 3kw Max lifting height: 1750mm Swiveling arm adjustments min: 650mm Swiveling arm max: 1050mm.

5 2KVA Generator: 8amp/12 volt dc max 240 volt ac Max watt: 2000 Deliver greater fuel efficiency via the built in – eco throttle weight: 21 kg Noise level: 53-59 db continous power output: 500w battery charging: yes.

6 MPFI Petrol engine Test Rig 600 – 800 CC, 3 Cylinder, 7 sensors and interface software.

7 Spot Welding Machine (Complete Set): 1.Primary voltage: to be suitable for 415v, 3 phase, 3 wire, 50 HZ, AC supply. 2. Rating @ 50% duty cycle: 200 KVA. 3. Secondary No load voltage ( in stages): 6-12v 4. Max. Welding current: 68KA 5. Secondary short circuit current: 85 KA (VDE 0545) 6. Max. Welding load: 680 KVA 7. Connected load: 520 KVA 8. Electrode pressure: 300 to 2500 KPA> 9. Electrode working range: 250mm 10. Arm spacing: 65/445mm 11. Clamping plates: (above): 400x400mm: (below): 400x400mm 12. Ventilation spacer: Rectangular cross section (2x10). Sq.mm 13. Max.dia of stamping : 1300mm 14. In case of segment dia. Uoto:3000mm 15. Thickness of ventilation stamping: up to 1.0mm. 16. Operating speed: 60 to 90 spots/min

Page 12: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

TENDER DOCUMENT FOR PROCUREMENT UNDER MHRD SCHEME OF UPGRADATION OF

EXISTING POLYTECHNICS

DEPARTMENT : COMPUTER ENGINEERING

S.

No

Laboratory

Name Of Equipment with Specification Make &

Model

Rate to be

Quoted

1 Computer Lab.

Intel(R) Core(TM) i7-2600(3.40 Ghz, 8 MB cache ,4 cores) processor or latest , 16 GB 1333 MHz DDR3 SDRAM , 1 T B SATA (7200 rpm) Hard Disk , 16 X SATA Super Multi DVD Writer , Network interface :wireless NIC 802.11b/g/n mini card, 19” TFT Monitor, USB Mouse- Key Board, Windows ®7 Professional 64 Operating system Genuine(preload) SSF(Small form Factor).

2 Color LaserJet Multifunction Printer All in one Functions: Print, Copy, Send-to-email/network folder. Print Speed: Normal for color/Black upto 31ppm. First Page out (black) : 10.9 sec / (color) : 12.2 sec Automatic Document feeder ADF, Automatic two sided Printing/copying . Scanner type : Flat bed, ADF Scan Resolution optical : up to 600 dpi Scan Size Flatbed/ADF: 8.5 X 14 in File format support: PDF, JPEG, TIFF, MTIFF

3 32 Port Switch

4 Wireless Access point compatible with IEEE 802.11b/g/n standard., data transmission up to 300 Mbps .Hardware specification Flash:4 MB,RAM 16 MB ,LAN one 10/100 Mbps UTP Port,Antenna :Two detachable dipole 3dbi antenna, Standard compliance : IEEE 802.3 10 Base-T Ethernet IEEE 802.3 u 100 Base-T X Fast Ethernet IEEE 802.3 11b IEEE 802.3 11g IEEE 802.3 11n

IEEE 802.1X RADIUS Authentication.

5 Printers & other peripherals:

Laser Printer: Print speed: Normal:Up to 40 ppm, Fisrt page out (ready) , Black:As fast as 7.5 sec ,Print quality black (best): Up to 1200 x 1200 dpi Print technology: Laser, Processor speed: 540 MHz Display: 2.25-in LCD (text) , 4 line display , up to 18 characters per line , ePrint capability: Connectivity, standard: 1 Hi-Speed USB 2.0 , 1 external Host USB , 2 internal Accessory ports Memory, standard: 128 MB, Memory, maximum: 640 MB Paper handling input, standard: 100-sheet multipurpose tray 1; one 500-sheet input tray 2; automatic duplex printing , Paper handling output, standard: 250-sheet

Page 13: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

output bin; 100-sheet rear output bin Duplex printing: Automatic (standard)

6 Printers & other peripherals:

Scanner / Photostat / Printer / Copier

7 Hard disk ( 500GB 7200 rpm SATA hard drive )

8 R A M ( 1 G.B. DDR1 )

9 SMPS 450 Atx

10 Mouse USB

11 Key Board USB

12 Lan Card USB

13 LCD Projector :- Resolution 1024x768 XGA,ANSI 3000 Lumens with all accessories

14 Digital Multimedia Projector Brightness (Lumens) : 1800 ANSI

Audible Noise: 43.0 Db

Size (cm) (HxWxD) :

7 x 29 x 23

Display:

Native: 800x600 Pixels

Maximum: 1024x768 Pixels

Digital Zoom: Yes

Digital Keystone: Vertical

Lens Shift: Vertical

Warranty: 2 Years

Life: 2000 hours

Speakers: 1.0 W Mono

Max Power: 240W

Voltage: 100V - 240V

Page 14: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

TENDER DOCUMENT FOR PROCUREMENT UNDER MHRD SCHEME OF UPGRADATION OF

EXISTING POLYTECHNICS

DEPARTMENT : ELECTRONICS & COMMUNICATION ENGINEERING

S.

No

Laboratory

Name Of Equipment with Specification Make &

Model

Rate to

be

Quoted

1 Software Lab. Computer Intel(R) Core(TM) i5/i7 processor 4GB PC2-6400 DDR2 SDRAM (800MHz) 500GB SATA II Hard Drive (300 MB/Sec @ 7200 RPM) 16X Super Multi Light Scribe ,Double Layer (8.5 GB) DVD Writer. 19” TFT Monitor, Mouse, Key Board Ps2, Windows 7(preload)

4 UPS offline 5 KVA Single Phase

5 LCD or LED TV 56” with USB Port Compatible with PC.

1 Electronic Fabrication Techniques Lab.

PCB Prototype Machine latest Model with PCAM and PCB design software and circuit simulation software.

2 Soldering & Desoldering stations

3 Drill Machine used in PCB 230V,1500 RPM which are adjustable in steps, with drill bits 0.8mm -5 nos,1.0mm-5 nos.

4 PCB designer Kit with content Rotring pens,Marker pens, Magnifing lens,Ruler,Stencils,cutter.Adhesive tape,srubber,cleaning reagent.

5 PCB curing Machine with Blower ,Heating area 12”*12” with accessories as tray , Brush ,PCB Laminate , Measuring Flask , Clips , Hand Gloves. A nd Chemicals as LPR Photoresist negative ,LPR Thinner , Developer ,Dye Blue ,Developer Part A ,Developer Part B ,Fecl3

6 Digital rework station

7 Portable Lith Camera for PAB Lab. ( Latest specifications )

8 Project Board Solder less high quality bread board with tie points 1685 .In built DC +5V/1A & variable DC power supply : 0 to +15V ( 500ma ) and 0 to -15V (500mA)

9 Programmable Logic controller Micro PLC from delta ,On board NO/NC switches High execution speed, PC based programming ,Soft copy of PLC introduction & Tutorials ,built –in power supplies.

10 Industrial PLC Micro PLC from Fatek , on board ON/NC switches ,On board IR switches ,Pc based programming ,soft copy of tutorials ,built in power supplies.

Page 15: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

11 CPLD Trainer kit Xilinx chip , usng VHDL software languages.

1 Digital & Microprocessor lab.

Microprocessor Training Kits Vinytics 8501L.

2 Microcontroller Development Board with Programmer

3 Advanced 8085 Microprocessor

Page 16: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

TENDER DOCUMENT FOR PROCUREMENT UNDER MHRD SCHEME OF UPGRADATION OF

EXISTING POLYTECHNICS

DEPARTMENT : WORKSHOP

S.

No

Laboratory Name Of Equipment with Specification Make &

Model

Rate to

be

Quoted

1 WORKSHOP Universal Milling Machine: Geared head universal milling machine having three outos feed. 1. Surface of table – 1220 x 280mm. 2. No. of T-slots 3x15 3. Longitudinal power & by hand- 660mm 4. Cross power & by hand 660mm. 5. Vertical power & by hand 406mm 6. Length of Arbor 635mm 7. No. of spindle speed 6 8. Head motor 2hp 9. Feed motor -2hp 10. Coolant motor-1/10hp App. Weight-2400kgs Dividing head and slotting attachment

2 Surface grinder: Working surface of table-600x200mm Max. job height admitted-275mm Long traverse of the table-650mm Cross traverse table Hyd -225mm Vertical traverse heel head-440mm Size of grinding wheel-250x19x76 to be supplied with Electro mag. Chuck. Coolant pump, wheel dressing attachment.

3 Universal cylindrical grinder with accessories: Centre distance 600mm Centre height-130mm Wheel head motor-3 H.P. Work head fitting taper-MT3 Work head motor- 1 h.p

Page 17: TENDER DOCUMENT FOR PROCUREMENT UNDER …kgpolytechnic.org/tenders/121123-tender-douments.pdf · existing polytechnics department: civil engineering s. no ... 8 digital balance

TENDER DOCUMENT FOR PROCUREMENT UNDER MHRD SCHEME OF UPGRADATION OF

EXISTING POLYTECHNICS

DEPARTMENT : COMMUNICATION SKILLS

S.

No

Laboratory Name Of Equipment with Specification Make &

Model

Rate to be

Quoted

1 Language lab – 30 User

Software – 1 Teacher + 30 User Application

2 Sound system with speaker and master control

3 Table with consoles to house 30 systems