Tender for Purchase of Items/Equipments for Electronics and

B.P.S. MAHILA VISHWAVIDYALAYA, KHANPURKALAN (SONIPAT)(A State University recognized under section 2(f) and 12 (B) of the U.G.C. Act 1956)

TENDER NOTICE

B.P.S. Mahila Vishwavidyalaya, Khanpur Kalan (Sonipat) requires to purchase

items/equipments for Electronics and Communication Labs of SES.

The cost of tender form is Rs. 1000/-. Last date of submission of bids is 17.09.12

upto 12.00 noon. For detail of items required & any clarification, visit the University

Website www.bpswomenuniversity.ac.in.

Reputed suppliers having experience of supplying similar items/equipments are

invited to submit technical and financial bids in separate sealed cover.

Registrar

Annexure-‘I’

BPS MAHILA VISHWAVIDYALAYA, KHANPUR KALAN (SONIPAT)(A State University recognized under Section 2 (f) and 12 (B) of the U.G.C. Act

1956)

SUPPLY OF ITEMS/EQUIPMENTS FOR ELECTRONICS AND COMMUNICATION LABSealed tenders are invited from respectable vendors for supply of items/equipments/software for various laboratories of Electronics and Communication Engineering of School of Engineering and Sciences of the University.1. Procedure

The bidder has to submit his bid in two separate sealed envelopes super scribing “Commercial Bid” and “Technical Bid” respectively. The commercial bid should contain the Financial Proposal for the University Electronics and Communication Engineering Lab equipments and Technical Bid should include Technical Proposal for the University Electronics and Communication Engineering Lab equipments.

2. About the UniversityBhagat Phool Singh Mahila Vishwavidyalaya, the first University for women in North India, was established under an act of the state legislature of Government of Haryana (No. UG 31/2006) on November 10, 2006 with the objective to make a profound difference in the lives of women by empowering them to attain their full potential though purist of knowledge, acquisition of skills, development of character and self-esteem and recognition of rights and responsibilities. It is recognized by University Grants Commission, India under section 12 B of UGC Act.The University has a sprawling campus spread in an area of over 500 acres of land. The university has more than 200 faculty members. The university has adequate teaching blocks, 14 hostels for about 3000 students with all modern facilities and about 150 staff quarters Staff Quarters for the teaching and administrative staff of the University alongwith a central library and language labs. A herbal garden, with medicinal plants in 12 acres of land, is being developed in the University campus with the help of Department of Forests, Government of Haryana and it will also be used as an amusement park for children with all modern facilities for children’s play, like swings and other amusement equipments.Within a short span of a few years, the University has been able to make its presence felt the world over. It is running more than 30 programmes in 06 Faculties and 4 Institutes, imparting education in various disciplines to more than 6000 students with an annual intake of more than 1200 students.The University in its functioning gets support and guidance from its Statutory Bodies such as the Court, the executive council, the Planning Board, the Academic Council and the Finance Committee. To facilitate the assigned role by these statutory bodies, the members of these bodies are the persons of eminence from varied fields and disciplines.

A large number of programmes are on anvil which includes a Medical College and Hospital, a Nursing College and a Dental College. The construction of the Hospitals has already begun. In addition, the University is also moving towards e-governance and proposes to have Wi-Fi in the entire campus. A lavish campus equipped with the latest infrastructure, right ambience and committed and qualified faculty makes it an ideal place for acquisition of knowledge and learning.

3. EMDThe EMD for the project is not less than 1% of total amount of the bid in the form of demand draft in favour of Registrar, BPS Mahila Vishwavidyalaya payable at Khanpur Kalan and same will be refunded to the unsuccessful bidders.

4. General Conditions4.1 The bidder must have requisite infrastructure and resources to successfully

execute the supply and install equipments in labs and provide services.4.2 The bidder should be a reputed Organization engaged in manufacturing and

supplying equipments to Govt. institutes and other technical institution of repute.4.3 Preference would be given to Bidder which is an ISO certified company or it must

be registered with appropriate authorities.4.4 Preference will be given to those who have branch office and support center in

Delhi-NCR for getting faster post- implementation technical support.4.5 The University reserves the right to carry out the capability assessment of the

bidder and the University’s decision shall be final & binding to all in this regard.4.6 Preference may be given to those bidders who are capable to supply complete

requirement of Electronics and Communication Engineering lab of the University.4.7 Incomplete tender such as unsigned tender, absence of supporting documents, late

submitted quotation, conditional quotation will not be accepted.4.8 Firms are required to supply the items within 04 weeks from the placement of the

order.4.9 The tender document must reach to the Registrar, BPS Mahila Vishwavidyalaya,

Khanpur Kalan (Sonipat) by hand or by registered post/speed post latest by 17.09.12 upto 12.00 noon

4.10 The dispute, if any, will be subject to jurisdiction at Sonipat or arbitration, the decision of the Vice-Chancellor will be final.

5. Eligibility ConditionsThe bidding is open to all qualified bidders who fully meet the following qualifying requirements:-

5.1 The bidder must have a proven track record of supplying lab equipments to . various technical institution of repute.

5.2 Bidder should be in operations for a minimum of last 5 years.5.2.1 Bidder should have a minimum turnover of Rs. 20 lacs (Rupees Twenty Lacs)

during last 3 financial years (in combination). The supplier should attach the certified copy of supply order lab equipments in Govt./Govt. autonomous organization.

5.3 Bidders should have sufficient technical professionals on rolls to cater unhindered university requirements.

5.4 The supplier should attach the certified copy of the registration of the firm.

6. Scope of WorkSupplier is expected to coordinate with university department once receiving the order and scope of the work includes:-

6.1 Analyzing and assisting in the design of the University labs.6.2 Providing specifications required (plumbing, electrical etc.) for the equipments to

be fitted in labs.6.3 Monitoring desired modification in labs.6.4 Installing the equipment, providing documentation and training of one week to the

staff and students free of cost.Instruction to Bidders.o Tender should be sent in sealed and super scribed envelops with mention of

Tender No. date and date of opening.o Late and delayed tender will not be considered at all.o Duties Taxes where legally leviable and intended to be claimed should be

distinctly shown separately in the Tender.o Your quotation should be valid for 80 days from the date of opening of tender.o Preference will be given to those tenders offering supplies from ready stock and

on the basis of F.O.R. Destination/Free door delivery at Site.o All available Technical Literature (s), Catalogue(s) and other data in support of

the specification and details of the item(s) should be furnished alongwith the offer.

o Samples, if any, called for, should be submitted free of all charges by the bidder and the Purchaser shall not be responsible for any loss or damage thereof due to any reason whatsoever. In the event of non-acceptance of tender, the bidder shall have to remove the samples at his own expense.

Specifications:o Technical Specifications of Equipment/Hardware/Software for various

laboratories of Electronics and Communication Engineering are attached separately as Annexure A.

o Store offered should strictly conform to our specifications. Deviation, if any, should be clearly indicated by the bidder in their quotation. The bidder should also indicate the make/type no. of the stores offered and provide catalogue(s), technical literature(s) and sample(s), wherever necessary along with quotations. Test certificates wherever necessary should be forwarded along with the supplies. Whenever options are called for in our specifications, the bidder should address all such options. Wherever specifically mentioned by us the bidder could suggest changes to specifications with appropriate response for the same.

o The purchaser shall be under no obligation to accept the lowest or any tender and reserves the right of acceptance of the whole or any part of the tender or portion of the quantity offered and the bidders shall supply the same at the rates quoted.

o Corrections, if any, must be attested. All amounts shall be indicated both in words as well as in figures. Where there is difference between amounts quoted in words and figures, amount quoted in words shall prevail.

o The bidder should supply alongwith the tender, the name of his bankers as well as the latest income tax clearance certificate duly countersigned by the Income Tax Officers of the circle concerned under the seal of his office.

o The purchaser reserves the right to place order on the successful bidder for additional quantity upto 25% of the quantity offered by them at the rates quoted.

o The authority of the person signing the tender, if called should be produced.o Complete system configuration and sub-system design details should have

approval of the purchaser before actual fabrication or procurement process.o A complete set of instruction and operation manual should be supplied at the time

of installation.o Final performance should be guaranteed at the site.

Terms and conditions of contract

1. Definitions:-a) The terms ‘Purchaser’ shall mean the Registrar, BPS Mahila Vishwavidyalaya,

Khanpur Kalan, Sonipatb) The term ‘Contractor’ shall mean, the person, firm or company with whom or

with which the order for the supply of stores is placed and shall be deemed to include the contractor’s successors, representative, heirs, executors and administrators unless excluded by the contact.

c) The ‘Stores’ shall mean that contractor agrees to supply under the contract as specified in the Purchase Order including erection of plants and machinery and subsequent testing, should such a condition be included in the Purchase Order.

d) The term ‘Purchase Order’ shall mean the communication signed on behalf of the purchaser by an officer duly authorized intimating the acceptance on behalf the purchaser on the terms and conditions mentioned or referred to in the said communications accepting the tender or offer of the contractor for supply of stores of stores or plant, machinery or equipment or part or thereof.

2. Prices:Tenders, offering firm prices will be preferred, where a price variation clause is insisted upon by a bidder, quotations with a reasonable ceiling should be submitted. Such offers should invariably be supported by the base price taken into account at the time of tendering and also the formula for any such variations.

3. Security DepositOn acceptance of tender, the contractor shall, at the potion of the Purchaser and within the period specified by him deposit with him in cash or any other form as the purchaser may determine, security deposit not exceeding ten percent of the value of the contract as the purchaser shall specify. If the contractor is called upon by the purchaser to deposit ‘Security’ and the contractor fails to provide the security within the period specified, such failure shall constitute a breach of the contract and purchaser shall be entitled to make other arrangements for the re-purchase of the stores contracted for at the risk of contractor and/or to recover from the contractor damages arising from such cancellation.

4. Guarantee and Replacement

a) The contractor shall guarantee that the stores supplied shall comply fully with the specifications laid down, for material workmanship and performance.

b) For a period of (12) twelve months after the acceptance of the stores, if any defects are discovered therein or any defects therein found to have developed under proper use arising from faulty stores, design or workmanship, contractor shall remedy such defects at his own cost provided he is called upon to do so within a period 14 months from the date of acceptance thereof by the purchaser who shall state in writing in what respect the store or any part thereof are faculty.

c) If in the opinion of the purchaser, it becomes necessary to replace or renew any defective stores such replacement or renewal shall be made by the contractor free of all costs to the purchaser provided the notice informing the contractor of the defect is given by the purchaser in this regard within the said 14 months from the date of acceptance thereof.

d) Should the contractor fail to rectify the defects the purchaser shall have the right to reject or repair or replace at the cost of the contractor the whole or any portion of the defective stores.

e) The decision of the purchaser, not withstanding any prior approval of acceptance or inspection thereof on behalf of the purchaser, as to whether or not the stores supplied by the contractor are defective or any defects has developed within the said period of 12 months or as to whether the nature of the defectives required renewal or replacement shall be final, conclusive and binding on the contractor.

f) To fulfill guarantee conditions outlined in Clause 4(a) to (d) above, the contractor shall, at the option of the purchaser, furnish a Bank Guarantee (as prescribed by the purchaser) from a Bank approved by the purchaser for an amount equivalent t to 10% of the value of the contract alongwith first shipment documents. On the performance and completion of the contract in all respects, the Bank Guarantee will be returned to the contractor without any interest.

g) All the replacement stores shall also be guaranteed for a period for 12 months from the date of arrival of stores at Purchaser’s site.

h) Even while the 12 months guarantee applied to all stores in case where a greater period is called forth by our specifications then such a specification shall apply; in such cases the period of 14 months referred to in Para 4 (b) and (c) shall be ‘asked for’ guarantee period plus two months.

5. Packing Forwarding & InsuranceThe contractor will be held responsible for the stores being sufficiently and properly packed for transport by rail, road, sea or air, to withstand transit hazards and ensure safe arrival at the destination. The packing and marking of packing shall be done by and at the expenses of the contractor. The purchaser will not pay separately for transit insurance, all risks in transit being exclusively of the contractor and the purchaser shall pay only for such stores as are actually received in good conditions, in accordance with contract.

6. Testing Certificate:Wherever required Test Certificate should be sent along with relevant dispatch documents.

7. Acceptance of Stores:

a) The stores shall be tendered by the contractor for inspection at such places as may be specified by the purchaser at the Contractor’s own risk, expenses and cost.

b) It is expressly agreed that the acceptance of stores, contracted for is subject to final approval by the purchaser, whose decision shall be final.

c) If, in the opinion of the Purchaser all or any of the stores that do not meet the performance or quality requirements specified in the Purchase Order, they may be either rejected or accepted at the price to be fixed by the purchaser and his decision as to rejection and the prices to be fixed shall be final and binding on the contractor.

d) If the whole or any part of the store supplied are rejected in accordance with Clause No. 7 (c) above, the purchaser shall be at the liberty, with or without notice to the Contractor, to purchase in the open market at the expenses of the Contractor, stores meeting the necessary performance and quality contracted for in place of these rejected, provided that either the purchase, or the agreement to purchase, from another supplier is made within six months from the date of rejection of stores as aforesaid.

8. Rejection of stores:Rejected stores will remain at the destination at the contractor’s risk and responsibility, if instructions for their disposal are not received from the Contractor within a period of 14 days from the date of receipt of the advice or rejection, the purchaser or his representative has at his discretion the right to scrap or seal or consign the rejected stores to the contractor’s address at the Contractor’s entire risk and expense, freight being payable by the Contractor at actual.

9. Delivery Period:a) The delivery period of the stores stipulated in the purchase order shall be deemed

to be the essence of the Contract i.e. 15 days, and delivery must be completed on or before the specified dates/period.

b) Should the contractor fails to deliver the stores or any consignment thereof within the period prescribed for such delivery, the purchaser shall entitled at his option either 1. to recover from the contractor as agreed liquidated damages and not by way of penalty, a sum of 2% of the price of any stores which the contractor has by failed to deliver as aforesaid for each month or part of a month, during which thedelivery of such stores may in arrears, or II. to Purchase elsewhere without notice to the contractor on the account and at the risk or the contractor, the stores not delivered or others of similar description (where other exactly complying with the particulars are not, in the opinion of the purchaser readily procurable, such opinion being final) without canceling the contract in respect of the consignment(s) not yet due for delivery or, III. To cancel the contract or a portion thereof, and if so desired to purchase or authorize the purchase of stores not so delivered or others of similar description (where other exactly complying with the particulars are not, in the opinion of the purchaser readily procurable, such opinion final) at the risk and cost of the contractor.

In the event of action being taken under sub-clause (ii) and (iii) of clause 9 above, the Contractor shall be liable for any loss which the Purchaser may sustain on that account, provided that the re-purchase, or, if there is an agreement to re-

provide shall made within (6) six months from the date of such failure. But the Contractor shall not be entitled to any gain on such re-purchase made against default. It shall not be necessary for the purchaser to serve a notice of such re-purchase on the defaulting Contractor. This right shall without prejudice to the right of the purchase to recover damages for breach of contract by the Contractor.

10. Extension of the Delivery Time:As soon as it is apparent that Contractor delivery period/dates cannot be adhered to, an application shall be sent by the Contractor to the Purchaser, if failure, on the part of the Contractor to deliver the stores in proper time shall have arisen from any cause which the Purchaser may admit as reasonable ground for an extension of the time and his decision shall be final he may allow such additional time as he considers it to be justified by the circumstances of the case without prejudice to the Purchaser’s rights to recover liquidated damages under claud 9 (i), (ii) and (iii).

11. Payment:Contractor’s bill will be passed only after the stores have been received, inspected and accepted by the Purchaser for payment.

12. Recovery of Sums Due:Whenever there is a breach of contract whether liquidated or not, money arising out of or under this contract against the contract, the Purchaser shall be entitled to recover such sum by appropriating in part or whole, the security desposited by the Contractor, if a Security is taken against the contract. In the event of the Security being insufficient or if no security has been taken from the Contractor, then the balance or the total sum recoverable as the case may be shall be deducted from any sum then due or which at any time thereafter may become due to the contractor under this or any other contract with Purchaser. Should this be not sufficient to cover the full amount recoverable, the Contractor shall pay to the Purchaser on demand the remaining balance due. Similarly, if the purchaser has or makes any claims, whether liquidated or not, against the Contractor under any other contract with purchaser, the payment of all money payable under the contract to the Contractor including the Security Deposit shall be withheld till such claims of the Purchaser are finally adjudicated upon and paid by the Contractor.

13. Indemnity:

The Contractor shall warrant and be deemed to have warranted that all stores supplied against this contract are free and clean of infringement of any patent, copy right or trade mark, and shall at all time indemnify the purchaser against all claims which may made in respect of the stores for infringement of any right protected by patent, registration of design or trade mark and shall take all risk of accidents of damage which may cause a failure of the supply from whatever cause arising and the entire responsibility for sufficiency of all the means used by him for the fulfillment of contract.

14. Arbitration:-In the event of any question, dispute or difference arising under these conditions contained in the purchase order in connection with this contract, (Expect as to any

matters the decision of which is specially provided for by these conditions), the same shall be referred to the sole arbitration of the Head of the Institution or of some other person appointed by him. It will be no objection that the arbitrator is a Government Servant, that he has to deal with matter to which the contract relates or that in the course of his duties as Government Servant he has expressed views on all or any of the matters in dispute binding on the parties of this Contract.

(a) It is Terms of the Contract:If the Arbitrator be the Head of the Institution:

I. In the event of his being transferred or vacating his office by resignation or otherwise, it shall be lawful for his successor-in-office either to proceed with the reference himself, or to appoint another person as arbitrator, or

II. In the event of his being unwilling or unable to act for any reason it shall be lawful for the Head of the Institution, to appoint another person as arbitrator, or

(b) If the Arbitrator be a Person appointed by the Head of the Institution:In the event of his death, neglecting or refusing to act, or resigning or being unable to act for any reason, it shall be lawful for the Head for the Head of the Institution either to proceed with reference himself or to appoint another person as arbitrator in place of the outgoing arbitrator. Subject as aforesaid, the Arbitration Act, 1940 and the rules there under and any statutory modifications thereof for the time being in force shall be deemed to apply to the arbitration proceedings under this clause. The Arbitrator shall have the power to extend with the consent of the purchaser and the contractor the time for making a publishing the award. The venue of Arbitration shall be Sonepat District (Haryana). In his absolute discretion may determine. Work under the contract shall if reasonably possible, continue during Arbitration proceedings.

15. Counter Terms and Conditions of Supplies: Where Counter Terms & Conditions/printed or cyclostyled conditions have been offered by the supplier, the same shall not be deemed to have been accepted by the purchaser, unless specific written acceptance thereof is obtained.

Annexure-‘A’

Specification

Of

Tender Documents for Various Laboratories

Of

Electronics and Communication Engineering

Of

School of Engineering and Sciences

Annexure-‘A’

BPS MAHILA VISHWAVIDYALAYA, KHANPUR KALAN (SONIPAT)(A State University recognized under Section 2 (f) and 12 (B) of the U.G.C. Act

1956)

Specifications:Technical Specifications of Equipment/Hardware/Software for various laboratories of Electronics and Communication Engineering are:

Linear Integrated Circuits LaboratoryThe major specifications of the instruments and training kits of Linear Integrated Circuits laboratory are as follows:-

S. No.

Item Name Specifications Quantity

Total Price (in Rupees)Inclusive of all i.e taxes, installation, commissioning, training

etc

01

OP-AMP based trainer kit for performing Adder, subtractor, Comparator, Integrator, Differentiator operations.

Function Generator:Output : Sine, Square and TriangleFrequency : 10 Hz 100 KHzDC Power Supplies : 0 - 5 V variable, 2 Nos.Mains power : 230V AC ±10% (Detachable mains chord to be provided)

05

02

Trainer kit to perform the operation of Active filters (LPF, HPF, BPF, Notch filter).

Function Generators :Sine Wave: 10 Hz 100 KHz Square Wave: 10 Hz 100 KHz Triangle Wave: 10 Hz 100KHz On board test Power Supplies: 0-5 V (variable)Main power : 230V AC ±10% (Detachable mains chord to be provided)

05

03Trainer kit to perform the operation of phase shifter & Wein bridge oscillator.

Function Generators :Sine Wave: 10 Hz 100 KHz Square Wave: 10 Hz 100 KHz Triangle Wave: 10 Hz 100KHz On board test Power Supplies: 0-5 V (variable)Main power : 230V AC ±10% (Detachable mains chord to be

05

provided)

04

Trainer kit to perform waveform generation (Astable & Monostable multivibrator) using OP-AMP

Function Generators :Sine Wave: 10 Hz 100 KHz Square Wave: 10 Hz 100 KHz Triangle Wave: 10 Hz 100KHz On board test Power Supplies: 0-5 V (variable)Mains power : 230V AC ±10% (Detachable mains chord to be provided)

05

05

Trainer kit to perform waveform generation (Astable & Monostable multivibrator) using 555 timer

Function Generators :Sine Wave: 10 Hz 100 KHz Square Wave: 10 Hz 100 KHz Triangle Wave: 10 Hz 100KHz On board test Power Supplies: 0-5 V (variable)Mains power : 230V AC ±10% (Detachable mains chord to be provided)

05

06 Trainer kit for V-I and I-V converter using OP-AMP.


05

07Trainer kit to perform operation of Instrumentation Amplifier using OP-AMP.


05

08

Desktop(Latest configuration)

CPU – Intel Core Duo 8400, 3GHz, 6MB, L2 Cache and 1333MHz FSB. Chipset – Intel Q35 or better on OEM MotherboardBus Architecture - Integrated Graphics, 2PCI, 1PCI Express x 1 and 1 PCI Express x 16Memory – 2GB 667MHz DDR2 RAM Expandable to 8GBHard Disk Drive – 250GB 7200rpm Serial ATA HDDMonitor – 43.2cm (17inch) TFT Digital Color MonitorKeyboard – 104 keysMouse – Optical

02

Bays – 4 Nos. (2Nos. 5.25 inches for Optical Media Drives and 2 Nos. 3.5 inches for Hard Disk Drives)Ports – 6 USB Ports ( With at least 2 in front) audio ports for microphone and headphone in front Cabinet – Mini TowerDVD ROM Drive – 8x or better DVD ROM Drive / DVD – RWNetwork Facility – 10/100/1000 on board integratedOperating System – Windows Vista Business preloaded with Media and Documentation and certificate of Authenticity.OS Certifications – Win Logo Vista Business OS and Linux certificationPower Management – Screen Blanking, Hard Disk and system Idle Mode in power on, Set up Password, Power Supply SMPS Surge protected.Preloaded Software – McAfee or equivalent antivirus (Latest Version) with 60 days License.

10 Printer

Printer Type: Laser, Mono Colour Resolution: 600*600 dpi, Paper size: A4 Printing Speed:25 PPM BW USB Port: 1 USB port. Category: Duplex, Network Card: Yes, Fax: Yes

02

11 Analog CRO

2 Channel-4 Trace Display,Bandwidth: DC-30MHz(-3dB)Modes: Normal, Search, Delay with LED indication.Triggering Modes: Auto or Normal.AC: 10Hz-25MHz, DC: DC-25MHz, HF: 1.5KHz-40MHz, LF: DC –1KHz,LED indication for trigger action.Sensitivity: internal 5mm, Ext. 0.5V, Component Tester: Current approx.8mA rms, Voltage approx. 8.5 Vrms, Test connection, continuity Tester with beeps sound. Main Voltages: 220-240V, 50Hz.Mains fluctuation: 10% plus, minus (max).Magnification: x-10 to 20ns/cm, Variable Hold-off.

10

12 10 MHZ Function Generator

Frequency Range: 0.2Hz-10MHz.Operating Modes: Sine, Square, Triangle, Pulse, TTL.Frequency Dislpay: 3.5 Digit LEDModulation: FM,AM Std, AM Bal, PWMPowerSupply:230V+10%,50HzAccessories: Operating Manual, BNC Cable.Mod. Freq. Range: DC to 20KHz. 20V (p-p) Output & DC Offset

05

14 Digital Multimeter

Display: 3.5 Digit ResolutionBasic VDC Accuracy: 0.0024% (1 yr.)Voltage : 100mV to 1000V Voltage Range, with up to 100nV ResolutionCurrent: 100μA to 10A Current Range, with up to 100pA ResolutionResistance: 10Ω to 1GΩ Range, with up to 10μΩ Resolution Testing: Diode and Continuity TestingMeasurement: Frequency and Period Measurements.Temperature and Capacitance Measurements.USB Port: USB Host Port on Front Panel for Easy Storage of Measurement Data and Instrument Settings.

07

15 Digital IC Tester

Test most of the Digital IC’s, Microprocessors, Static & Dynamic RAMs & peripheral ICs, 40 pin ZIF to test IC’s in DIP package, Protection against wrong insertion, Repeated testing of same IC without re-entering the IC number, Auto find the number of digital IC’s up to 20 pins, Seven segment displays & keyboard, Buzzer sound for fault diagnostic IC, In built power supply.

03

Microprocessor and Interfacing laboratoryThe quantity and major specifications of the Microprocessor and Interfacing laboratoryitems are:

S.no Item Name Specifications Quantity Total Price (in Rupees)

Inclusive of all i.e taxes, installation, commissioning, training etc

1. 8085 Microprocessor Training Kit

Processor: Intel 8085A CPU @6.144 MHz Clock speed.4 K powerful monitorFIRMWARE. Including all standard commands, codes, functions and utility subroutines.Memory: RAM: 32KB, EPROM: 32 KBKeyboard and Display:IBM-PC keyboard(104 keys)16*2 alphanumeric Dot Matrix liquid Crystal Display with back lightTimer and Bus Expansion :16-bit programmable counter/timer, 8 TTL I/O lines, terminated at FRC connector.Digital I/O lines are terminated in 20-pin connector.Interface: RS232C compatible serial Port through SID/SOD line with auto baud rate.Cross AssemblerPowerful 8085 interrupt capabilities.SMPS Power Supply:(multi output) Input : 230 V A.C, Output:+5V/3.5 A,+12V/150mA

15

Processor:INTEL 8086 CPU AT 6.144 MHz Clock SpeedMemory: 32KB for monitor 15

2. 8086 Microprocessor Trainer Kit

EPROM. 64 KB RAM Battery backup provision for RAM Two modes of operation: 1. Monitor mode: User interaction through 28 Keys Hex Keypad and 8 digit seven segment display.2. Serial Mode: Through RS -232 serial port with a terminal.Keyboard and Display:16*2 Alphanumeric LCD Display101 keys IBM compatible keyboardTimer, Parallel I/O, Serial & Bus Expansion:48 TTL I/O lines using two 8255 PPI chips and all signals terminated on two 26 pin FRCConnectors.RS 232C compatible serial port brought out to a pin D type male connector.3-channel 16-bit counter/timer using 8253.Software:Built-in line assembler & disassembler.Documentation Support:86 Technical reference manual.User/student work book.Addon Cards:Channel DAC Interface Board:Two Numbers of DAC 0800.Analog output:+5V to -5V.DAC outputs are terminated at a suitable connector.Provision for test points & fault analysis points.8 channel ADC (0809) Interface Board:Display of digital data using LED’s.8 channel analog inputs.

3. 8251 & 8253 Incorporates INTEL 8253 Timer & USART 8251.

Interface Card Selection of I/O addresses through jumper.LED indicators are provided for testing I/P's for 8251 and 8251 chip signals.External /Internal/manual input clock to 8253.Baud Rate generation for 8251 using 8253. Manual pulse keys with LED indicator is provided to see how exactly data transferTakes place.Standard RS232C serial port. Compatible with 8085,8086 CPU based microprocessor kits

4

4. Keyboard/Display Interface card

INTEL 8279 Keyboard/Display interface.Selection of I/O addresses through jumper.6-Digit Display & 18-keys Keyboard.Provision for Control & shift Keys.Facility for Interrupt I/O Transfer.Provision for test points & fault analysis points.Provision to connect IRQ,output line of 8279 to any interrupts RST 5.5, 6.5or7.5. Compatible with 8085,8086 CPU based microprocessor.

5

5. 8255 Interface Card

Incorporates INTEL 8255, Programmable Peripheral Interface Chip.All essential extra hardware provided to operate 8255 in mode 0 or mode 1 or mode 2.8 Nos. of SPDT switches provided at Port A for giving 8 TTL inputs.8 LED’s provided at Port b for outputs.Provision to interrupt CPu in Mode 1 and Mode2. Compatible with 8085, 8086

5

CPU based microprocessor.

6. DC Motor Speed measurement & Control Card

8 Bit-DAC to control the speed & direction of DC motor.6V DC motor with slotted disk optical pick with wave shaping circuitry for speed sensing.Speed measurement through 8253 counter channel 0 is used for measuring the speed of DC motor by decrement the counter value using pulses generated by opto-coupled DC motor shaft .Compatible with 8085, 8086 CPU based microprocessor.

5

7. 8259 Interface Card

Incorporates INTEL 8259, interrupt controller chip.8 switches for giving interrupts.8 IRQ lines.Compatible with 8085, 8086 CPU based microprocessor.

5

8. Stepper Motor Controller Interface

Control Stepper Motor in three parameters such as direction, speed & number of steps.It has got driver transistors for

driving all the phases of the motor.Useful for robotics & control applications.

5

9. Traffic Light Controller Card

The Traffic Light Controller Card has RED; YELLOW & GREEN LED’s to demonstrate the use of Microprocessor 8085/8086 in controlling the traffic movement under the control of program.It is a good example of use of

Microprocessor in common applications

5

10. Printer Interface Card

Uses 8255 of the microprocessor 8085/8086 to print output on to the printer.Inbuilt power supply

5

CPU: Intel Core 2 dual 8400,3 GHz, 12 MB L2 Cache & 1333

11. Desktop(Latest Configuration)

MHz FSBChipset: Intel Q 35 or better on OEM motherboardBus Architecture: Integrated graphics, 2 PCI, 1 PCI Express *1 and 1 PCI Express * 16.Memory: 2 GB 677 MHz DDR2 RAM Expandable to 8 GB.Hard Disk Drive: 250 GB 7200 rpm Serial ATA HDD.Monitor: 43.2 cm(17 inch) TFT Digital Color Monitor.Keyboard: 104 Keys.Mouse: Optical.Bays: 4 Nos. (2 Nos. 5.25 inches for Optical Media Drives and 2 Nos. 3.5 inches for HDD).Ports: 6 USB ports (with at least 2 in front) audio ports for microphone and headphone in front.Cabinet: Mini Tower.DVD ROM Drive: 8 * or better DVD ROM Drive/ DVD-RWNetwork Facility: 10/100/1000 on board integrated Network Port with remote booting facility remote system installation, remote wake up, out of band management using any standard management software.Operating System: Windows Vista Business preloaded with media and Documentation and certificate of authenticity.OS Certifications: Win logo Vista Business OS and Linux Certification.Power Management: Screen Blanking, HDD and system Idle Mode in power on, Set up

03

password, Power supply SMPS Surge protected.

12 Printer

Colour Resolution : 600*600 dpi, Paper size: A4Printing Speed: 20 PPM BW USB Port: 1 USB port.Network Card: NA

2

Electronics Devices and Circuits

The quantity and major specifications of the Electronics Devices and Circuits Laboratory

items are:

S.NoItem Name Specifications

Quantity

Total Price (in Rupees)Inclusive of all i.e taxes, installation, commissioning, training etc

01

Trainer Kit to study Diode as series & shunt positive& negative, biased series& shunt positive& negative and combination clipper circuits and having positive, negative & biased clamper circuits.

Should have in built power supplyMain supply: 230 V+_ 10% , 50 Hz;Sine wave Generator: 1Khz, 15V, Vpp, DC Power supply:0-5V(2nos.)

05

02

Trainer Kit to study PN Diode/Zener diode& LED characteristics for forward& reverse biased.

Both Si & Ge Diodes, Zener & LEDDC power supply:+12VAmmeter range:1uA-200mA,Voltmeter range: 1mV-200V, Mains power: 230V AC+_10% 50 Hz

05

03

Trainer Kit to study characteristics of PNP, NPN transistor in CE,CB& CC configurations.

DC power supply:+5V,-5V,12V,-12VAmmeter range:1uA-200mA,Voltmeter range: 1mV-200V, Mains power: 230V AC+_10%, transistors: BC548, 2N3906

05

04Trainer Kit to study DC Voltage Doubler/Tripler circuits

Multi Output AC Voltage Source:1.5-12V, DC Voltmeter: 0-60V, 4 Diodes(4007), 4 Capacitors(220uF/63V), Electronic AC Voltmeter Of Dual Range: 0-1V&0-12V(AC), 10 load resistors: 10ohms-20Kohms

05

05Trainer Kit to study FET characteristics

DC Power supply: +5V,-5V, +12V,-12V Voltmeter range: 1mV-200V, Ammeter range: 1uA-200mA, Main supply: 230v+_10% 50 Hz, FET:J122A

05

06Trainer Kit to study Dual

Gate MOSFET characteristics

Three regulated DC supplies: 0-1V, 0-3V & 0-20V. Two Voltmeters(one in dual range)& one Ammeter.One Dual gate MOSFET 3N200 or equivalent Main supply: 230V+_10% 50 Hz,

05

07Trainer Kit to study SCR characteristics

DC Power supply: +35V, +15V, 250mA , Voltmeter: 200V DCAmmeter: 200mA

05

Main supply: 230V+_10% 50 Hz,

08Trainer Kit to study I-V characteristics of UJT

Two regulated DC Power supply, 0-20V each. Two Voltmeters & one Ammeter Main supply: 230V+_10% 50 Hz,UJT-2N2646, DC supply short circuit& overload protected.

05

09Trainer Kit to study DIAC characteristics

Power supply output: +35V DC(250mA), -35V DC (250mA) , Fuse:500mAVoltmeter: 35V DC, Ammeter: 35mAMain supply: 230V+_10% 50 Hz,DIAC-DB3

05

10

Trainer Kit to study Input/Output characteristics of 3 terminal IC Regulator

Three terminal regulator(7805 mounted upon sink), Variable DC power supply for input:1.5V-10V, One voltmeter, One AmmeterOperable on 220V/50 Hz AC

05

11Trainer Kit to study I-V characteristics of Photo voltaic cell.

Variable regulated DC voltage:2-12v/21wOne photo voltaic cell:SE,VR-122One high impedance voltmeterOne miliammeter, Two decades of RLMains: 220V/50Hz AC

02

12

1 MHz Microcontroller based Function Generator with backlit LCD display simultaneous for frequency & amplitude & built in frequency counter

Frequency range:0.1Hz-1MHz in 7 decade steps, Operating modes: sine, square, triangle, pulse or frequency modulatedFrequency accuracy: +_0.5%Frequency counter:-Frequency range: DC to 50 MHzResolution: 1HzSensitivity: 0.5 voltsFrequency display: LCD controlled by Micontroller

05

13

30 MHz Microcontroller based 2 Channel- 4 Traceoscilloscope with Digital readout

Bandwidh:30MHz, 2 channel 4 trace digital readout oscilloscope Display:*10 magnificationInput voltage: Max. 400V (DC+ PeakAC)Component & continuity tester

05

14. Desktop CPU: Intel Core 2 dual 8400,3 GHz, 12 MB L2 Cache & 1333 MHz FSBChipset: Intel Q 35 or better on OEM motherboardBus Architecture: Integrated graphics, 2 PCI, 1 PCI Express *1 and 1 PCI Express * 16.Memory: 2 GB 677 MHz DDR2 RAM Expandable to 8 GB.

02

Hard Disk Drive: 250 GB 7200 rpm Serial ATA HDD.Monitor: 43.2 cm(17 inch) TFT Digital Color Monitor.Keyboard: 104 Keys.Mouse: Optical.Bays: 4 Nos. (2 Nos. 5.25 inches for Optical Media Drives and 2 Nos. 3.5 inches for HDD).Ports: 6 USB ports (with at least 2 in front) audio ports for microphone and headphone in front.Cabinet: Mini Tower.DVD ROM Drive: 8 * or better DVD ROM Drive/ DVD-RWNetwork Facility: 10/100/1000 on board integrated Network Port with remote booting facility remote system installation, remote wake up, out of band management using any standard management software.Operating System: Windows Vista Business preloaded with media and Documentation and certificate of authenticity.OS Certifications: Win logo Vista Business OS and Linux Certification.Power Management: Screen Blanking, HDD and system Idle Mode in power on, Set up password, Power supply SMPS Surge protected.Preloaded Software: McAfee or equivalent antivirus(Latest Version) with 60 days validity

15 Laser Printer(HP) Resolution in dpi: Mono 600*600Paper size: A4, Print speed in PPM(A4 Size): 20, Port:1 USB, Memory in MB : NA, Network card: NA 2

Note: Circuit diagram should be printed on the top of board and two sets of manual with each trainer kit.

EDC Lab -II

S. No Specifications Quantity Total Price (in Rupees)Inclusive of all i.e taxes, installation, commissioning, training etc

01. Analog Electronics Lab Trainer with ready to use board for Experiments on Analog electronics

Reg. DC Power Supplies : +5 V - 1 A, ±12 V – 500mA (Fixed), ±12 V - 500 mA (Variable)AC Supply : 9 V - 0 V - 9 V / 500 mABreadboard : 172.5 mm × 128.5 mmFunction generator :Operating modes : Sine, Square, TriangularFrequency range : 1 Hz to 100 KHzModulation /Audio gen. :Operating modes : Sine, Square, TriangularFrequency range : 1 Hz to 10 KHzContinuity tester : For testing the continuity.

Provided with Beeper Sound.

Interconnection : 2 mm patch cordsPower Supply : 220 V ±10 %,50Hz Power Consumption : 3 VA (approx.)Accessories Included : Mains cord, Mains power : 230V AC ±10% (Detachable mains chord to be provided)Warranty : 02 years Manual: Extensive e manual should be provided

5

. Optional boards required with analog lab trainer with no components on the top.

1a. Transistor Series Voltage regulator 51b. Transistor Shunt Voltage regulator 51c. Class B Push pull Emitter follower 21d. Single Stage RC Coupled BJT Amplifier 51e. Cascade Amplifier 51f. Phase shift oscillator Transistorized 51g. Hartley Oscillator 51h. Colpitts oscillator 51i. Class A Power amplifier 51j. Class C Tuned amplifier 51J. Second order Active filter (HP & LP) 51k. Active Notch Filter 51l. Wein Bridge oscillator 51m. Phase shift oscillator 51n. Two stage RC Coupled amplifier 5

Circuit Simulation LaboratoryThe major specifications of the simulation tool/hardware for circuit simulation laboratoryare as follows:

S.No Laboratory Name

Item Name & Specifications Quantity Make/Brand


1 Circuit Simulation Laboratory

Circuit Simulation NI Multisim education/Academic License, Latest Version: 25 User

01(25User)

National instruments

PCB designing NI Ultiboard education: 10 Users

01(10 Users)

Multipurpose Virtual Instrumentation Suite NI ELVIS II Hardware only

01

2 Laser PrinterA4 size medium speed laser printer Mono 22 PPM with network card & Duplexers

1 hp or any other with similar specification

Total

Digital System Design LaboratoryThe major specifications of the circuit simulation tool for Digital System Design Laboratory

S.No Item Name Specification Quantity Total Price (in Rupees)Inclusive of all i.e taxes, installation, commissioning, training etc

1 VHDL Design software

Xilinx ISE design suite system edition latest version(13.1)

25 user

2(a) VLSI Trainer Kits

Universal FPGA/ CPLD Development Board with Parallel port JTAG Programming

3 kits

2(b) VLSI Trainer Kits

Universal FPGA/ CPLD Development Board with USB Programming

1 kits

2(c) VLSI Trainer Kits

FPGA Development board with USB programming

1 kits

2(d) VLSI Trainer Kits

CPLD Trainer with parallel port interfaceBased on Xilinx 9572 PC84-CPLD

1 kits

5 Printer HP Laser JetMultifunction printer with networking features

01

Electrical Engineering LaboratoryThe quantity and major specifications of the Electrical Engineering Laboratory items are:

Sr.No.

Item Name Specifications Quantity Required


1 Trainer kit to verify Kirchhoff’s current and Kirchhoff’s Voltage law

Main Supply:-230 ±10% ,50HzD.C Power supply:- +12VInbuilt Digital D.C Voltmeters

with 3½ digits display:- (0-10V, 0-5V)Digital D.C Ammeter:- (2µA-200mA)Main ON/Off Switch and fuseNote:-Different types of resistances and resistance network should be mounted behind the front panel of Kit

03

2 Trainer kit to verify Norton,Superposition and Reciprocity theorems

In built SMPS power supply. Inbuilt digital (LCD) ammeter 2mA- 200mA for current measurement. On board DC power supply: +12V, ±5V, 500mA.Note:- (a)Circuit diagram should be printed on the top of the trainer with no components on the top. (b) Test points provided on board to measure voltage, current & resistance at various points. (c)Trainer should be encased in a plastic molded box.

03

3 Trainer kit to verify Thevenin Theorm and Maximum Power Transfer theorem

In built SMPS power supply. On board Voltmeter LCD : 200mV to 200 V. On board Ammeter LCD : 2mA to 200 mA. On board DC power supply: +12V, ±5V, 500 mA. Note: - a) Test points provided on board to measure voltage, current &

03

resistance at various points. b) Only circuit diagram should be printed on the top of the trainer with no components on the top. c)Trainer should be encased in a plastic molded box.

4 RLC series and parallel Resonance Trainer kit

In built SMPS power supply. Onboard Signal Generator Output: 8Vpp 0nboard Frequency Counter with ranges:-1KHz, 10KHz, 60KHz. Onboard LCD Voltmetre:-2V. Main ON/Off Switch and fuse. Note:- a) Circuit diagram should be printed on the top of the board. b) Test points should be providedon board to measure voltage, current & resistance at various points. c) Multiple combinations of components to be provided. d)Trainer should be encased in a plastic molded box.

03

5 Control panel for (i)Performing load test of transformer and plot load current Vs (a) terminal voltage (b) efficiency(ii)Measure iron loss in a Single phase transformer and to find the equivalent circuit parameters by performing open circuit and short circuit test

Panel for circuit diagram including Main Supply: 240V±10% ,50 HzInbuilt Single Phase Autotransformer:- (0-270V,5A)Inbuilt Single phase Transformer Rating: 1KVA, 240 V/50 HzPrimary Voltage 0-125V, 0-125V. Secondary Voltage 0-125V, 0-125V. MCB:-5 A Meter Used on Panel: Voltmeter (MI) - 300V -2 Nos. Voltmeter (MI) - 50 V -1 No. Ammeter (MI):-5 A-2 Nos. Ammeter (MI):-100 mA-1 No. Wattmeter:-100W Wattmeter:-500W Note: - a) BS 10 Type Safety terminals

01

and patch chord should be provided. b) Circuit diagram should bescreen printed on the top of the Panel.

6 To perform O.C and S.C Tests of three phase induction motor

Main Supply: Three phase,415V±10% ,50 HzMeter Used on Panel:-Wattmeter:-500W-2Nos.Voltmeter (MI)- 500 V Ammeter (MI):-5 AAssembled withThree phase auto transformer: 440V/10 AThree phase induction motor: Type: Squirrel cage Rating:-1 HP R.P.M:-1440 r.p.m MCB:- 5 A Note:-a)Motor should be mounted on a M.S channel base.b)Indication light for all three phases. c)Separate terminals BS 10 type of windings brought out on a terminal box fitted on top of the motor for connection with control panel using BS10 type patch cords.d)Different colour Annunciators should be provided for all three phases. e)Safety terminals and patch chord should be provided.

01

7 To measure power in three phase system by Two Wattmeter Method

Main Supply: Three Phase 415V±10% ,50 HzMeter Used on Panel:-Ammeter(MI)- (0-1A)Voltmeter(MI) -0-500VWattmeter-0-500W (2 Nos.)Load:- R-LMCB-10 ALamp load (Resistive type) with load range of 0-1.2KW in steps of 100W to be provided with only switches on the top & lamps to be

01

provided inside the box. On board MI Ammeter (10A) & indication light for power on.Assembled withThree phase auto transformer:440V/10ANote:-a) Patch chords: BS 10 type should be provided. b) BS 10 Type safety terminals & patch chord should be provided for safety purpose.

8 Electrical Safety Demonstrator

Transparent Model of MCB with Fuse with variable supply on board. Simulation diagram of earting circuit should be printed on board. Ammeter should be provided on board. Trainer should be encased in a plastic molded box. Trainer should be able to perform experiments like a) Study of importance of Earthing in any electrical device. b) Study of role of Fuse in any electrical or electronic circuit. c) Study of importance and working of Miniature Circuit Breaker (MCB).

01

09 Single phase induction type energy Meter

Range: - 5-20 A.Reference Voltage: - 240V.Reference Frequency: - 50 Hz.Starting Current: - 0.4 % of basic current.Display: - Electromechanical counter with one decimal.Overload Capacity: - 400% & 600% of basic current.LED’s:- 4 LED’s for display of meter calibration, reverse indication, phase available indication, earth temper indication.

02

10 Rheostat 50 ohm, 240V, 5A 0111 Single Phase (0-270V, 5A) 1

Autotransformer 12 Sodium Vapour

lamp60W 1

75W 1

13 Electric drill machine with stand

Drill machine with 2 H.P Motor 1

14 Bit set 3-12mm ,Diamond 01set15 Bit 8-20mm, Diamond 01 set16 High Pressure

Mercury vapour lamp

80W 1

125W 1

17 Electrodynamics type Wattmeter

Class of accuracy + 1.5% of F.S.D. Range : 0-0.5/1 Amps, 0-75/150/300 Volts

01

18 Insulation Tester Analog + Digital Display (Log scale for insulation measurement): User Selectable Backlit Display. Test Voltages :50V/100V/250V/500V/1000V. Insulation Resistance Measurement:10K Ω to 2G Ω. Hands-free continuity testing. Voltmeter :Instrument measures voltages from 25V to 600V AC/DC. Capacitive devices under test, such as cables and windings, that get charged during the test, are discharged by the tester. Live circuit detection:Displays presence of voltages >25V irrespective of function selected. Pre-selectable measurement time for Insulation. Resistance Measurement: Lead resistance null facility: Storage Memory for last 10 readings: Blown fuse indication: Low battery indication should displayed on LCD: Stop Watch: allows you to measure elapsed time up to 1 hour.

1

Auto-power off function The instrument turns off automatically, if any of the keys or the selector switch have not been activated for about 10 minutesin insulation range and 5 minutes in other ranges or can be switched to continuous operation. Protective holster for rough duty should be provided. Accesories : Probes & manual. Battery : 6 x 1.5 V cells

19 Earth Tester 100 ohm, Earth 01

20 Frequency Meter Panel Tupe frequency meter to measure Max. 99.99 Hz . 4 digit LED Display. Mains operated

01

21 Digital Tachometer

Portable, battery operated, 4 digit, LED, 1 to 9999 rpm, contact type.

01

22 Power Factor Meter

Display:-4 digital.Accuracy:- 0.5% ± 3 digitVoltage testing:-up to 440 V or 660 V ± 10%.Measuring range:- 0-1.00 (C or L)Maximum Signal Consumption< 0.3 VA.

01

23 Desktop Computer

CPU: Intel Core 2 duo 8400, 3 GHz, 12 MB L2 Cache & 1333 MHz FSB. Chipset: Intel Q 35 or better on OEM motherboard. Bus Architecture: Integrated graphics, 2 PCI, 1 PCI Express *1 and 1 PCI Express * 16. Memory: 2 GB 677 MHz DDR2 RAM Expandable to 8 GB. Hard Disk Drive: 250 GB 7200 rpm Serial ATA HDD. Monitor: 43.2 cm (17 inch) TFT Digital Color Monitor. Keyboard: 104 Keys. Mouse: Optical. Bays: 4 Nos. (2 Nos. 5.25 inches for Optical Media Drives and 2 Nos. 3.5 inches for HDD).

01

Ports: 6 USB ports (with at least 2 in front) audio ports for microphone and headphone in front. Cabinet: Mini Tower. DVD ROM Drive: 8 * or better DVD ROM Drive/ DVD-RW. Network Facility: 10/100/1000 on board integrated Network Port with remote booting facility remote system installation, remote wake up, out of band management using any standard management software. Operating System: Windows Vista Business preloaded with media and Documentation and certificate of authenticity. OS Certifications: Win logo Vista Business OS and Linux Certification. Power Management: Screen Blanking, HDD and system Idle Mode in power on, Set up password, Power supply SMPS Surge protected. Preloaded Software: McAfee or equivalent antivirus (Latest Version) with 60 days validity.

24 Laptop Processor: Mobile Intel Core 2 Duo ProcessorP8700, 2.53GHZ with 3 MB L2 cache 1066 MBZ FSB or better. Chipset & Motherboard: GM 45 or higher Chipset on OEM Mother board. Memory:1 x 2GB DDR2 RAM expandable up to 4 GB. HDD: 250GB 5400 rpm (min) SATA Display Screen: 14” (35.6 cm) or above (TFT) actuve Narrux .Resolutiion: Display Video Controller Integrated GMA500 series with 128 MB Shared Memory.

01

Wireless ConnectivityIntegrated Wireless Intel 802.11 a/b/n, Integrated Blue tooth. DVD Writer Speaker:Integrated DVD Writer 8x and Integrated stereo Key board: Key board with Touch paid Expansion port:3 USB, 10/100 Ethernet card, RGB or video or VGA, PCI Express slot, microphone, stereo headphone & standard features. Operating system Norton/ Software: Microsoft windows vista Business preinstalled and McAfee/ e-trust, & other software, Antivirus latest version with 60days license. Power Supply: 4hrs, 230V, 50Hz AC Supply with rechargeable Battery pack comprising of Li-ION battery Suitable for approx. Operation complete with battery charger/ adaptor. Carrycase: To be provided

25 Printer Colour Resolution: 600*600 dpi, Paper size: A4 Printing Speed:20 PPM BW USB Port: 1 USB port. Category: Duplex, Network Card: NA, Fax: No

1

26 Educational Charts of Electrical Engineering lab

……………………….. 5

Annexure-“II”

Sr No.

Item Name Specification Quantity Total (Approx.cost)

1 DigitalMultimeter

Display: 6.5 Digit Resolution Basic VDC Accuracy : 0.0024% (l yr.)Voltage : 100 mV to 1000 V Voltage Range, with up to 100 nv Resolution , Current: 100 uA ro 10 A Current Range, with up to 100 pA ResolutionResistance: 10 Ω to 2 GΩ Range, with up to 10µΩ ResolutionTesting: Diode and Continuity TestingMeasurement: Frequency and Period Measurements .Temperature and Capacitance Measurements. USB Port: USB Host Port on Front Panel for Easy Storage of Measurement Data and Instrument Settings.

7 nos.

2 CRO Display: 2 Channel—4 Trace.Bandwidth: DC-30MHZ(-3dB) Modes: Normal. Search, Delay with LED indication. Triggering Modes: Auto or normal, AC: 10Hz—25MHz,DC: DC-25MHz, HF:1.5KHz-40MHz. LF: DC -lKHz, LED indication for trigger action.Sensitivity: internal 5mm, Ext. 0.5V ' Component Tester: Current approx. 8 mA rms, /—Voltage approx. 8.5Vrms, Test connection, continuity 'Tester with beeps sound. Mains Voltages: 220—240V, 50Hz. Mains fluctuation:10% plus,minus(Max) Magnification: x-10 to 20ns/cm.Variable hold·off USB Port: Removable Data Storage using the front-panel USB Port

8 nos.

3 10 MHZ Function Generator

Frequency Range: 0.2Hz-10MHz.Operating Modes: Sine, Square, Triangle, Pulse,TTL .Frequency Display: 3.5 Digit LEDModulation : FM, AM Std , AM Bal, PWMPower supply: 230V+10%, 50HzAccessories: Operating manual, BNC Cable. Mod. Freq. Range: DC to 20KHz.20V(p-p) Output & DC Offset

10 nos.

4 FM Modulation

Sine Wave Audio oscillator: 300Hz-5KHz with adjustable amplitude(0-2Vpp)and frequency.

02 nos.

& De- Modulation

Carrier Signal Generator: Frequency 455 KHz Amplitude:0-1 Vpp.Low pass filter: Cut-off Freq: 4KHz with adjustable gain.Method of Modulation: Reactance and Varactor Diode.Ampltude limiter.Mixer/Amplifier with gain adjustment.Demodulation method: 1. Detuned Resonant Detector 2. Foster Seeley Detector.Fault points.Power supply: 230V,50Hz.Accessories: Line Chord, Manual, Patch Chord

5 Single side band Modulation and demodulation

Sine Wave Audio Frequency Signal Amplifier: Frequency:300Hz-10KHz with adjustable amplitude (0-240mVpp).Method of Modulator: Balanced Modulator using IC LM 1496Filter: Band Pass Filter using Crystal.Demodulation Method: Foster-Seeley Detector with Local Oscillator 455KHz.Test points/Fault pointsPower Supply:230V,50Hz

02 nos.

6 SSB AM ReceiverTrainer

Construction: Super hetrodyne Receiver.Frequency Range: 980KHz-2.50MHz.IF Frequency:455KHzInputs:1. RF Amplifier 2. Mixer 3.Local oscillator 4.Beat Frequency Oscillator 5.IF Amplifier.Tuning: Ganged Capacitor with value.Receiving Media: Telescopic Antenna/RF Cable.Detector: Product DetectorOutput: Amplifier with speaker.Test Points/faulty points with option to show waveform at different test points.Inbuilt Power Supply:12V or 5V/500mA.Power Supply: 230V,50HzAccessories: Manual,Patch Cords.

02 nos.

7 SSB Transmitter Trainer

Audio Oscillator: Frequency: 300Hz-5KHz.Amplitude: 4Vpp Both adjustableAudio Output: Amplifier with speaker.Modulator: Balanced modulators with Band Pass Filter.Transmitter Amplifier Output: DSB (1 MHz) SSB(1.445 MHz) connecting to antenna cable.Fault Switches.Power Supply: 220V,50 Hz.Accessories: Manual,Patch Cords.

2 nos.

8 PAM/PPM/PWM Modulation

Sine wave audio freq.generator: Freq: IKHz & 2KHz.Amplitude:0-10Vpp.Square wave Signal Generator:

2 nos.

& De-Modulation

Freq: 1KHz & 2KHz.Amplitude:0-5Vpp.Sampling Pulse Generator:Freq:8KHz,16KHz,32KHz & 64KHzAmplitude :5VppDemodulation: 4th order/LPF & AC Amplifier with adjustable gain.DC output:0-4V(Variable)Test poins/fault switches.Power supply:220V AC, 50HzAccessories: Sensitive MIC, Ear phone, power chords, patch cords manuals

9 Analog signal sampling and reconstruction trainer

Crystal oscillator 6.5 MHzSine Wave generatorFreq. 1KHz. Amplitude 5VppSampling freq. (switch selectable with LED display): Freq. 4KHz, 8KHz,16KHz, 32KHz and 64KHzBandwidth: 2nd and 4th order LPF with cut off freq. 3.4KHzTest points & fault switches.Power Supply: 220V AC, 50HzAccessories: Power Chords, Patch Chords and Manuals

2 nos.

10 Time Division Multiplexing and and

IP Channel: 2 Time division multiplex serial inputPower supply: 220V AC, 50HzAccessories: power chords, patch cords, manuals.

2 nos.

11 Pulse Code Modulation

Power supply: 220V AC, 50HzAccessories: power chords, patch cords, manuals.

2 nos.

12 Freq. Division Multiplexing

Power supply: 220V AC, 50HzAccessories: power chords, patch cords, manuals.

2 nos.

11 Desktop CPU: Intel core 2dual8400,3GHz, 12MB 1.2 Cache and 1333MHz FSBChipset: Intel Q35 or better on OEM motherboardBus Architecture: integrated graphics, 2 PCI, 1PCI Express* 1 and 1PCI express* 16.Memory: 2GB 677MHz DDR2 RAM expandable to 8GB.Harddisk Drive: 250 GB 7200RPMSerial ATA HDDMonitor: 43.2cm(17inch) TFT Digital color monitorKeyboard: 104 keys Mouse: opticalBays : 4 No.(2 No. 5.25 inches for optical media drives and 2 no. 3.5 inches for HDDPorts: 6 USB Ports(with at least 2 in front) audio port for microphone and headphone in front

1 nos.

Cabinet: MinitowerDVD ROM Drive: 8* or better DVD ROM Drive/DVD-RWNetwork Facility: 10/100/1000 onboard integrated network port with remote booting facility remote system installation, remote wake up, out of band management using any standard managementsoftwareOperating System : Windows Vista Business preloaded with media and documentation and certificate of authenticity.OS Certifications: Win logo Vista Business OS and LINUX certificationPower Management: Screen Blanking, HDD and System idle mode in power on ,setup password, Power Supply SMPS surge protected Preloaded Software: McAfee or equivalent antivirus(latest version) with 60 days validity

12 EMONA kit EMONA Base units alongAddon cards

2 nos.

13 Display charts

AM, SSB, FM, Radio receiver, EM spectrum, Digital modulation-1-2, Sampling and encoding techniques, TDM, FDM techniques

10 nos.

Signature of the tenderer

B.P.S MAHILA VISHWAVIDYALAYA, KHANPUR KALAN (SONIPAT)(A State University recognized under section 2 (f) and 12 (B) of the U.G.C. Act 1956)

Website: www.bpswomenuniversity.ac.in

Telephone No. 01263-283001,002

Tender fee Rs. 1000/- tender no. BPSMV-SES (Elect. & Comm. Labs)

Last date of receiving tender:17.09.12 upto 12.00 noon Opening Date:17.09.12 at 3.00

pm.

Tender fee amount to Rs. 1000/- has been deposited vide Receipt No./Draft No.

_________ dated ________

TENDER FORM

Tender for:

From (Name, Postal Address & Telephone no. of the firm):

ToRegistrar, BPS Mahila Vishwavidyalaya, Khanpur Kalan (Sonipat)

We agree to abide by the terms & conditions mentioned in annexure ‘I’. All the pages

have been signed by us in token to our acceptance of the terms mentioned therein Rates

for the supply of the items and the quantity to be supplied mentioned against each being

submitted vide Annexure II’ Goods will be delivered in a period of ……………… Days

from the date of the receipt of the purchase order. The rates quoted are valid upto …….

Days from the date of opening the tender.

Period of Guarantee/Warranty Shall be …………..

Earnest Money: 1% of Bid Amount i.e. amounting Rs. ………………….

is enclosed vide D.D./Pay order no. ___________________ dated ____________.

Copies of certified certificate from Chartered Accountant showing turnover for

the financial year 2010-11/Proof of completion of two works of similar nature during

financial year 2008-2009 & 2009-2010/PAN No. …………/VAT registration No.

……………….. are enclosed.

I/We have understood the items of the tender annexed at annexure-II and have

thoroughly examined the specifications/drawing and/or pattern quoted or referred to

herein and/are fully aware of the nature of the stores required and my/our offer is to

supply the stores strictly in accordance with the requirements subject to the terms and

conditions contained in the Purchase Order, if communication on the acceptance of this

tender either in whole or in part.

Signature of office sealDated;

(Bidder)