00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00

00

3030

3030

1010

1010

2020

2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead A

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt on to the alternator pulley. Make sure the belt is under the motor pulley belt retaining clip. Slide the green handle to the right, locking the handle into the retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE (hold for no more than 3 seconds). Observe meters for proper readings.

Red clip

pdc/nwr/inv/881/881-manual/green/889-A.cdr

Black clip

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0, unless W connectedthen 7 to 8

STARTER VOLTAGESTATOR VOLTAGE

0, unless W connectedthen 7 to 8

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead B

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

W terminal, connected onlywhen W spade is presenton alternator

pdc/nwr/inv/881/881-manual/green/889-B.cdr

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

7 to 8

STARTER VOLTAGESTATOR VOLTAGE

7 to 8STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead BD

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

pdc/nwr/inv/881/881-manual/green/889-BD.cdr

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

13-16

STARTER VOLTAGESTATOR VOLTAGE

13-16STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead BM

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

If battery post is notavailable,connect here

pdc/nwr/inv/881/881-manual/green/889-BM.cdr

EXTERNALLYREGULATED

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0, unless W connectedthen 7 to 8

STARTER VOLTAGESTATOR VOLTAGE

0, unless W connectedthen 7 to 8

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead BT

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-BT.cdr

W terminal, connected onlywhen W spade is presenton alternator

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead C

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

pdc/nwr/inv/881/881-manual/green/889-C.cdr

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead CD

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

pdc/nwr/inv/881/881-manual/green/889-CD.cdr

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00

00

3030

3030

1010

1010

2020

2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

7-8

STARTER VOLTAGESTATOR VOLTAGE

7-8STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

Red clip

Black clip pdc/nwr/inv/881/881-manual/green/889-D.cdr

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Test Lead D

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

EXTERNALLYREGULATED

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead El1

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clipGreen

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

pdc/nwr/inv/881/881-manual/green/889-EL1.cdr

EXTERNALLYREGULATED

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead EL2

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

6.Reverse the BLACK and GREEN test lead wires and retest.

Red clip

Black clipGreen

Black

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

pdc/nwr/inv/881/881-manual/green/889-EL2.cdr

FLD FLDFLD FLD

EXTERNALLYREGULATED

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

7 to 8

STARTER VOLTAGESTATOR VOLTAGE

7 to 8STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead EL3

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%..

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clipGreen

White

Black

pdc/nwr/inv/881/881-manual/green/889-EL3.cdr

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

EXTERNALLYREGULATED

STA

FLD

GRD

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

7 to 8 (sta)14-16 (61, d+)

STARTER VOLTAGESTATOR VOLTAGE

7 to 8 (sta)14-16 (61, d+)

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead EL4

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clipGreen

White

Black

pdc/nwr/inv/881/881-manual/green/889-EL4.cdr

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

EXTERNALLYREGULATED

D-D-FLD

or DFFLD

or DFB+

D-

F+

61

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

7 to 8

STARTER VOLTAGESTATOR VOLTAGE

7 to 8STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead F

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

pdc/nwr/inv/881/881-manual/green/889-F.cdr

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

EXTERNALLYREGULATED

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead FA

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin. Make sure “A” circuit adapter is connected.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

pdc/nwr/inv/881/881-manual/green/889-FA.cdr

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

“A” Circuit

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-FB.cdrTest Lead FB “A" CircuitTest Lead FB “A" Circuit

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

7 to 8

STARTER VOLTAGESTATOR VOLTAGE

7 to 8STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead FC

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clippdc/nwr/inv/881/881-manual/green/889-FC.cdr

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

EXTERNALLYREGULATEDGreen

White

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead FT

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clippdc/nwr/inv/881/881-manual/green/889-FT.cdr

EXTERNALLYREGULATED

Green

Red

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead FV

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-FV.cdr

W terminal, connected onlywhen W spade is presenton alternator

W terminal, connected onlywhen W spade is presenton alternator

W TerminalW Terminal

Slide on connector usedwhen post is not present D+

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

7 to 8

STARTER VOLTAGESTATOR VOLTAGE

7 to 8STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead G

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than10 seconds.

Red clip

Black clip

pdc/nwr/inv/881/881-manual/green/889-G.cdr

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

EXTERNALLYREGULATED

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00

00

3030

3030

1010

1010

2020

2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0, unless Pconnected, then 7 to 8

STARTER VOLTAGESTATOR VOLTAGE

0, unless Pconnected, then 7 to 8

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

Red clip

Black clip pdc/nwr/inv/881/881-manual/green/889-H.cdr

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Test Lead H

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

“P” terminal, connectedonly when P spade is presenton alternator

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00

00

3030

3030

1010

1010

2020

2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

Red clip

Black clip pdc/nwr/inv/881/881-manual/green/889-HL.cdr

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Test Lead HL

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead ID

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-ID.cdr

SLSL

IGIG

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead IG

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-IG.cdr

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead IN

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-IN.cdr

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

7 to 8

STARTER VOLTAGESTATOR VOLTAGE

7 to 8STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff

Test Lead J

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%..

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-J.cdr

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

EXTERNALLYREGULATED

onononon

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead JD

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-JD.cdr

L S

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

7 to 8

STARTER VOLTAGESTATOR VOLTAGE

7 to 8STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff

Test Lead K

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%..

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-K.cdr

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

EXTERNALLYREGULATED

offoff

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

Red clip

Black clip Pdc/nwr/inv/881/881-manual/green/889-LR.cdrTest Lead LR

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

STARTER VOLTAGESTATOR VOLTAGE

13 to 16

STARTER VOLTAGESTATOR VOLTAGE

13 to 16

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff

Test Lead M

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%..

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-M.cdr

EXTERNALLYREGULATED

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

STARTER VOLTAGESTATOR VOLTAGE

13 to 16

STARTER VOLTAGESTATOR VOLTAGE

13 to 16

offoff

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

Red clip

Black clip Pdc/nwr/inv/881/881-manual/green/889-MD.cdrTest Lead MD

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

STARTER VOLTAGESTATOR VOLTAGE

13 TO 16 if "R" terminalis present

0 if no "R" terminal

STARTER VOLTAGESTATOR VOLTAGE

13 TO 16 if "R" terminalis present

0 if no "R" terminal

L RL R

SS

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clipPdc/nwr/inv/881/881-manual/green/889-N-A.cdr

Test Lead N “A" CircuitTest Lead N “A" Circuit

onon

STARTER VOLTAGESTATOR VOLTAGE

7 to 8

STARTER VOLTAGESTATOR VOLTAGE

7 to 8

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Red clip

Black clipPdc/nwr/inv/881/881-manual/green/889-N-B.cdr

Test Lead N “B” CircuitTest Lead N “B” Circuit

STARTER VOLTAGESTATOR VOLTAGE

7 to 8

STARTER VOLTAGESTATOR VOLTAGE

7 to 8

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

offoff

EXTERNALLY REGULATED

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%..

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead P

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin. Make sure “A” circuit adapter is connected.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-P.cdr

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

“A” Circuit

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

7 to 8

STARTER VOLTAGESTATOR VOLTAGE

7 to 8STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead S

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Pdc/nwr/inv/881/881-manual/green/889-S.cdr

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

0 20010050 150

STARTERAMPS

02

4 68

10

MILLIAMPEREMETER

0 3010 20

ALTERNATOR VOLTAGE

0 3010 20

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

2 to 12STARTER AMPERAGE

0

4amp

Blue

Green

Red

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

off off off

Test Lead SC

Test Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Readings for a good alternator are in the shaded area. All meter

Red clip

Black clip

0 3010 20

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-SJ.cdr

EXTERNALLYREGULATED

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead SI

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Pdc/nwr/inv/881/881-manual/green/889-SI.cdr

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

STARTER VOLTAGESTATOR VOLTAGE

6 to 8(some Cadillac alternators

may read less)

STARTER VOLTAGESTATOR VOLTAGE

6 to 8(some Cadillac alternators

may read less)

1 21 2

RR

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead SJ

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-SJ.cdr

EXTERNALLYREGULATED

F1 F2

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead SK

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-SK.cdr

EXTERNALLYREGULATED

F1 F2

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00

00

3030

3030

1010

1010

2020

2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0, unless Pconnected, then 7 to 8

STARTER VOLTAGESTATOR VOLTAGE

0, unless Pconnected, then 7 to 8

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

Red clip

Black clip Pdc/nwr/inv/881/881-manual/green/889SL.cdr

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Test Lead SL

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

“P” terminal, connectedonly when P spade is presenton alternator

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead SN

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-SN.cd

EXTERNALLYREGULATED

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead T

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Pdc/nwr/inv/881/881-manual/green/889-T.cdr

Black clip

00 30301010 2020

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead TD

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-TD.cdr

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER AMPERAGE0

STARTER AMPERAGE0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead U

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Pdc/nwr/inv/881/881-manual/green/889-U.cdr

Black clip

00 30301010 2020

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead V

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin. Make sure “A” circuit adapter is connected.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button MOMENTARILY and RELEASE. Observe meters for proper readings. Hold for no more than 3 seconds.

Red clip

Black clip

Pdc/nwr/inv/881/881-manual/green/889-V.cdr

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

“A” Circuit

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

13-16

STARTER VOLTAGESTATOR VOLTAGE

13-16STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead VO

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-VO.cdr

EXTERNALLYREGULATED

D+D+

B+B+

D+ DFD+ DF

D-D-

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

13-16

STARTER VOLTAGESTATOR VOLTAGE

13-16STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead VW

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-VW.cdr

EXTERNALLYREGULATED

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead WF

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-WF.cd

EXTERNALLYREGULATED

00 2002001001005050 150150

STARTERAMPS

STARTERAMPS

0022

44 6688

1010

MILLIAMPEREMETER

MILLIAMPEREMETER

00 30301010 2020

ALTERNATOR VOLTAGE

ALTERNATOR VOLTAGE

00 30301010 2020

ALTERNATORAMPS

ALTERNATORAMPS

STARTER VOLTAGESTATOR VOLTAGE

0

STARTER VOLTAGESTATOR VOLTAGE

0STARTER AMPERAGE

0STARTER AMPERAGE

0

4amp

4amp

BlueBlue

GreenGreen

RedRed

BAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHTBAD DIODE LIGHT CHARGE LIGHT AUXILIARY LIGHT

MILLIAMPERE METER6 or less

MILLIAMPERE METER6 or less

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR VOLTAGE13 to 16

ALTERNATOR AMPERAGE12 to 16

ALTERNATOR AMPERAGE12 to 16

offoff offoff offoff

Test Lead Y

Test LeadsTest Leadsand881 Alternator

Starter Test Bench

Many alternators use the same plug with different wiring. Please refer to test lead chart for the correct test lead requirements!

1. Readings for a good alternator are in the shaded area. All meter readings are ±5%.

2. Insert lead as shown below and slide alternator onto alternator holder pin.

3. Install the belt making sure it is under the belt retaining clip. Slide the green handle to the right, locking handle into retaining tab and close the belt guard. Make sure to keep your fingers and clothing free of the pulley and belt.

4.Turn on motor switch. The charge light on the panel should be lit. If not, check and reset the circuit breaker on the front panel.

5. Press the GREEN test button. While pressing button, observe meters for proper readings. Hold for no more than 10 seconds.

Red clip

Black clip

00 30301010 2020

STARTER / STATORVOLTAGE

STARTER / STATORVOLTAGE

Pdc/nwr/inv/881/881-manual/green/889-Y.cd

EXTERNALLYREGULATED