Test Report - Index of ./ftp/faenl.msi.com/ftp/CE Documents/Notebook/MS-1656x (GT640, GX640)/CE_IT... · Report No： 098S084-IT-CE-P01V01 Page: 3 of 112 Laboratory Information We,

Test Report

Product Name ： Notebook PC

Model No. ： MS-1656, MS-1657

Marketing Name ： GT640, GX640

Applicant ： Micro-Star Int’L Co., Ltd.

Address ： No., 69, Li-De St., Chung-Ho City, Taipei Hsien, Taiwan

Date of Receipt ： 2009.08.20

Issued Date ： 2009.09.09

Report No. ： 098S084-IT-CE-P01V01

Report Version ： V2.0

The test results relate only to the samples tested.The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF, NVLAP or any agency of the Government. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation.

Report No： 098S084-IT-CE-P01V01

Page: 2 of 112

Test Report Cert i f icat ion Issued Date : 2009.09.09 Report No. : 098S084-IT-CE-P01V01

Product Name : Notebook PC

Applicant : Micro-Star Int’L Co., Ltd.

Address : No., 69, Li-De St., Chung-Ho City, Taipei Hsien, Taiwan

Manufacturer : MSI ELECTRONICS (KUNSHAN) CO., LTD.

Model No. : MS-1656, MS-1657

Marketing Name ： GT640, GX640

Brand Name : msi

EUT Voltage : AC 100-240 V / 50-60 Hz

Applicable Standard : EN 55022: 2006+A1: 2007

EN 61000-3-2: 2006

EN 61000-3-3: 1995+A1: 2001+A2: 2005

EN 55024: 1998+A1: 2001+A2: 2003

Test Result : Complied

Performed Location : Suzhou EMC Laboratory

No.99 Hongye Rd., Suzhou Industrial Park Loufeng

Hi-Tech Development Zone., Suzhou, China

TEL: +86-512-62515088 / FAX: +86-512-62515098

Documented By :

( Engineering ADM: Kayla Kan )

Reviewed By :

( Engineering Supervisor: Coffon Ye )

Approved By :

( Engineering Manager: Dream Cao )


Page: 3 of 112

Laboratory Information

We, QuieTek Corporation, are an independent EMC and safety consultancy that was established the whole facility in our laboratories. The test facility has been accredited/accepted(audited or listed) by the following related bodies in compliance with ISO 17025, EN 45001 and specified testing scope:

The related certificate for our laboratories about the test site and management system can be downloaded from QuieTek Corporation’s Web Site : http://www.quietek.com/tw/emc/accreditations/accreditations.htm The address and introduction of QuieTek Corporation’s laboratories can be founded in our Web site : http://www.quietek.com/ If you have any comments, Please don’t hesitate to contact us. Our contact information is as below: HsinChu Testing Laboratory :

No.75-2, 3rd Lin, Wangye Keng, Yonghxing Tsuen, Qionglin Shiang, Hsinchu County 307, Taiwan, R.O.C. TEL:+886-3-592-8858 / FAX:+886-3-592-8859 E-Mail : [email protected]

LinKou Testing Laboratory :

No. 5, Ruei-Shu Valley, Ruei-Ping Tsuen, Lin-Kou Shiang, Taipei, Taiwan, R.O.C. TEL : +886-2-8601-3788 / FAX : 886-2-8601-3789 E-Mail : [email protected]

Suzhou Testing Laboratory : No.99 Hongye Rd., Suzhou Industrial Park Loufeng Hi-Tech Development Zone., SuZhou, China

TEL : +86-512-6251-5088 / FAX : 86-512-6251-5098 E-Mail : [email protected]

Taiwan R.O.C. : BSMI, NCC, TAF

Germany : TUV Rheinland

Norway : Nemko, DNV

USA : FCC, NVLAP

Japan : VCCI


Page: 4 of 112

TABLE OF CONTENTS Description Page 1. General Information .......................................................................................................7 1.1. EUT Description .......................................................................................................7 1.2. Mode of Operation..................................................................................................10 1.3. Tested System Details ............................................................................................13 1.4. Configuration of Tested System..............................................................................14 1.5. EUT Exercise Software ..........................................................................................15 2. Technical Test ..............................................................................................................16 2.1. Summary of Test Result .........................................................................................16 2.2. List of Test Equipment ............................................................................................17 2.3. Measurement Uncertainty ......................................................................................20 2.4. Performance Criteria ..............................................................................................21 3. Conducted disturbance at mains terminals and telecommunication ports ...................22 3.1. Test Specification....................................................................................................22 3.2. Test Setup ..............................................................................................................22 3.3. Limit………………………........................................................................................22 3.4. Test Procedure .......................................................................................................23 3.5. Deviation from Test Standard..................................................................................24 3.6. Test Result..............................................................................................................25 3.7. Test Photograph .....................................................................................................43 4. Radiated disturbance...................................................................................................46 4.1. Test Specification....................................................................................................46 4.2. Test Setup ..............................................................................................................46 4.3. Limit………………………........................................................................................47 4.4. Test Procedure .......................................................................................................48 4.5. Deviation from Test Standard..................................................................................48 4.6. Test Result..............................................................................................................49 4.7. Test Photograph .....................................................................................................55 5. Harmonic current emissions ........................................................................................57 5.1. Test Specification....................................................................................................57 5.2. Test Setup ..............................................................................................................57 5.3. Limit…………………….. .........................................................................................57 5.4. Test Procedure .......................................................................................................59 5.5. Deviation from Test Standard..................................................................................59 5.6. Test Result..............................................................................................................60 5.7. Test Photograph .....................................................................................................62 6. Voltage fluctuations and flicker ....................................................................................63 6.1. Test Specification....................................................................................................63


Page: 5 of 112

6.2. Test Setup ..............................................................................................................63 6.3. Limit……………… ..................................................................................................63 6.4. Test Procedure .......................................................................................................64 6.5. Deviation from Test Standard..................................................................................64 6.6. Test Result..............................................................................................................65 6.7. Test Photograph .....................................................................................................66 7. Electrostatic discharge.................................................................................................67 7.1. Test Specification....................................................................................................67 7.2. Test Setup ..............................................................................................................67 7.3. Limit……………… ..................................................................................................67 7.4. Test Procedure .......................................................................................................67 7.5. Deviation from Test Standard..................................................................................68 7.6. Test Result..............................................................................................................69 7.7. Test Photograph .....................................................................................................73 8. Radio-frequency electromagnetic field.........................................................................77 8.1. Test Specification....................................................................................................77 8.2. Test Setup ..............................................................................................................77 8.3. Limit………………………........................................................................................77 8.4. Test Procedure .......................................................................................................77 8.5. Deviation from Test Standard..................................................................................78 8.6. Test Result..............................................................................................................79 8.7. Test Photograph .....................................................................................................80 9. Fast transients .............................................................................................................81 9.1. Test Specification....................................................................................................81 9.2. Test Setup ..............................................................................................................81 9.3. Limit………………………........................................................................................81 9.4. Test Procedure .......................................................................................................82 9.5. Deviation from Test Standard..................................................................................82 9.6. Test Result..............................................................................................................83 9.7. Test Photograph .....................................................................................................84 10. Surges .........................................................................................................................86 10.1. Test Specification....................................................................................................86 10.2. Test Setup ..............................................................................................................86 10.3. Limit……………………. ..........................................................................................86 10.4. Test Procedure .......................................................................................................87 10.5. Deviation from Test Standard..................................................................................87 10.6. Test Result..............................................................................................................88 10.7. Test Photograph .....................................................................................................89


Page: 6 of 112

11. Radio-frequency continuous conducted.......................................................................90 11.1. Test Specification....................................................................................................90 11.2. Test Setup ..............................................................................................................90 11.3. Limit………………………… ....................................................................................91 11.4. Test Procedure .......................................................................................................91 11.5. Deviation from Test Standard..................................................................................92 11.6. Test Result..............................................................................................................93 11.7. Test Photograph .....................................................................................................94 12. Power-frequency magnetic field...................................................................................96 12.1. Test Specification....................................................................................................96 12.2. Test Setup ..............................................................................................................96 12.3. Limit…………………….. .........................................................................................96 12.4. Test Procedure .......................................................................................................96 12.5. Deviation from Test Standard..................................................................................97 12.6. Test Result..............................................................................................................98 12.7. Test Photograph .....................................................................................................99 13. Voltage dips and interruptions....................................................................................100 13.1. Test Specification..................................................................................................100 13.2. Test Setup ............................................................................................................100 13.3. Limit………………………......................................................................................100 13.4. Test Procedure .....................................................................................................100 13.5. Deviation from Test Standard................................................................................101 13.6. Test Result............................................................................................................102 13.7. Test Photograph ...................................................................................................103 14. Attachment ...........................................................................................................104 EUT Photograph ...............................................................................................................104


Page: 7 of 112

1. General Information 1.1. EUT Description

Product Name Notebook PC

Model No. MS-1656, MS-1657

Marketing Name GT640, GX640

Brand Name msi Note:

This product includes four models for different marketing requirement, from these models, MS-1656 was

selected as the test model and its test data was recorded in this report.

Keypart List

Item/Vendor Model Description msi P/N

MB

msi MS-16561

CPU

Q2V3 OA3-1675001

Q2VD OA3-1675002

Q2VG OA3-1675003

Q2VM OAA-1675001

Q3BA A09-16200R6-I06

Intel

Q3B9 A09-17201T6-I06

LCD

SUMSUNG LTN154MT02 WSXGA+ S1J-690G010-S02

CHIMEI N154I3-L03 WSXGA+ S1J-640G029-CC1

HDD

WD2500BEVT 1st 250GB S71-2425521-W36

WD5000BEVT-xxZAT0 500GB S71-2450501-W36

Western Digital

WD3200BEVT-22ZCT0 1st 320GB S71-2432501-W36

MK2555GSX-AZK 250GB S71-2425531-T14

MK3263GSX 320GB S71-2432525-T14

TOSHIBA

MK5055GSX-AZK 500GB S71-2450504-T14

FUJITSU MHZ2320BJ 320GB S71-2432702-F06

Western Digital WD3200BEKT-22F3T0 320GB S71-2432701-W36

ODD

HLDS GT30N SUPER MULTI S7D-2270031-H44


Page: 8 of 112

SONY AD-7560S SUPER MULTI S7D-2270001-SI4

TSST TS-L633C SUPER MULTI S7D-2270026-T87

SONY BC-5500S-AH Blue Ray Disk S7D-2280006-SI4

HLDS CT10N Blue Ray Disk S7D-2280002-H44

SONY AD-7580S SUPER MULTI S7D-2270013-SI4

Memory

Transcend

(Samsung) TS128MSK64V1U-S DDR3 1066 1GB S7C-S448801-T10

Hynix HMT112S6BFR6C-G7N0 DDR3 1066 1GB S7C-S448201-H23

Transcend

(Samsung) TS256MSK64V1U-S DDR3 1066 2GB S7C-S458801-T10

Hynix HMT125S6BFR8C-G7N0 DDR3 1066 2GB S7C-S458201-H23

Transcend

(Samsung) TS128MSK64V3U 1333 1GB S7C-S449801-T10

UNIFOSA GU672203EP0300 1333 1GB S7C-S449101-U37

UNIFOSA GU612303EP0300 13332GB S7C-S459101-U37

Transcend

(Samsung) TS256MSK64V3U 13332GB S7C-S459801-T10

WLAN

INTEL 512AN_HMW 802.11n,PCI/HALF MINI CARD S57-0800183-I06

msi RT3090 Wireless 802.11b/g/n mini-card 605-6891-010

TWINHAN AW-NE785H, 802.11b/g/n,MINI-CARD HALF S57-0800290-T46

MDC

CastleNet D40 MODEM MODULE/HD AUDIO AND

AC-LINK DUAL MODE S52-2801210-C59

Bluetooth

msi MS-3801 MS-3801 0A (BC4) Main Board 605-3801-010

Keyboard

CHICONY MP-08C23US-3 S1N-3UUS1C1-C54

LITE-ON SG-29511-XUA US

S1N-3UUS2E1-L05

Touchpad

Synaptics TM-00300-000 1st S78-3700360-SD2

Sentelic TPA2D2IC99RA1 2nd S78-3700360-SK9

inverter

SAMPO YIVNMS0018D11-A S78-3300450-SG3

SUMIDA IV14080 S78-3300341-S49


Page: 9 of 112

MITAC DA-1A08-MS01L S78-3300540-M47

Power Cord

Isheng V50VS334B12180MS K33-3001020-I45

Battery

MITAC BTY-M66 6 cell 2400 S9N-1564221-M47

SMP BTY-M68 CBB 9cell S9N-1194210-SB3

SMP BTY-M68/SQU-718 9cell S9N-1196200-SB3

Adapter

LITEON PA-1121-04 120W S93-0403040-L05

ASUS ADP-120ZB BB

Camera

BASION N2934VV6-000/OV3640 3.0M S1F-0004030-B36

CHICONY CNF723121004441L

CHICONY CNF823921004442L

SMP 8025

TV tuner

AVERMEDIA A337F OS3-1121010

VGA

NVIDIA N10E-GE 602-V167-09S


Page: 10 of 112

1.2. Mode of Operation QuieTek has verified the construction and function in typical operation. All the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as:

Pre Test Mode

Emission

Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Mode 2: LCD (1680*1050@60Hz) + HDMI (1680*1050@60Hz) Mode 3: LCD (1280*800@60Hz) + VGA (1280*800@60Hz) Mode 4: LCD (1280*800) + HDMI (1280*800@60Hz) Mode 5: LCD (1280*800@60Hz) + VGA (1280*800@60Hz) Mode 6: LCD (1280*800) + HDMI (1280*800@60Hz) Mode 7: LCD (1280*800@60Hz) + VGA (1280*800@60Hz) Mode 8: LCD (1680*1050@60Hz) + HDMI (1680*1050@60Hz)

Final Test Mode

Emission Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz)

Immunity Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz)


Page: 11 of 112

Mode1 Mode2

CPU Q3BA Q3BA

Memory TS256MSK64V1U-S HMT112S6BFR6C-G7N0

HDD WD3200BEVT-22ZCT0 WD5000BEVT-xxZAT0

LCD LTN154MT02 LTN154MT02

ODD GT30N AD-7580S

Bluetooth MS-3801 10 MS-3801 10

Wlan RT3090 RT3090

TV Tuner A337F A337F

MXM card N10E-GE N10E-GE

Battery BTY-M66 BTY-M66

Adapter LITEON / PA-1121-04 LITEON / PA-1121-04

Camera BN2934VV6-000/OV3640 BN2934VV6-000/OV3640

Modem D40 AM5 D40 AM5

Keyboard CHICONY/MP-08C23U4-359 CHICONY/MP-08C23U4-359

Mode3 Mode4

CPU Q3B9 Q3B9

Memory HMT125S6BFR8C-G7N0 TS128MSK64V3U

HDD MHZ2320BJ WD2500BEVT

LCD N154I3-L03 N154I3-L03

ODD CT10N TS-L633C


Wlan RT3090 512AN_HMW



Battery BTY-M68/SQU-718 BTY-M68 CBB


Camera CHICONY/CNF723121004441L CHICONY/CNF823921004442L




Page: 12 of 112

Mode5 Mode6

CPU Q3B9 Q3B9

Memory TS256MSK64V3U GU612303EP0300

HDD MK3263GSX MK5055GSX- AZK

LCD N154I3-L03 N154I3-L03

ODD BC-5500S-AH BC-5500S-AH


Wlan AW-NE785H AW-NE785H



Battery BTY-M68/SQU-718 BTY-M68/SQU-718


Camera SMP/8025 BN2934VV6-000/OV3640



Mode7 Mode8

CPU Q3B9 Q3BA

Memory GU672203EP0300 TS128MSK64V1U-S

HDD MK2555GSX -AZK WD3200BEKT-22F3T0

LCD N154I3-L03 LTN154MT02

ODD BC-5500S-AH AD-7560S


Wlan AW-NE785H RT3090



Battery BTY-M68 CBB BTY-M66


Camera BN2934VV6-000/OV3640 BN2934VV6-000/OV3640




Page: 13 of 112

1.3. Tested System Details The types for all equipments, plus descriptions of all cables used in the tested system (including inserted cards) are:

Product Manufacturer Model No. Serial No. Power Cord

1 LCD Monitor DELL 3008WFP 7735432490P08B Non-Shielded, 1.8m

2 CRT ‘’21 IBM 6652-U3N 3 Non-Shielded, 1.8m

3 Microphone & Earphone SALAR N/A 5 N/A

4 Microphone & Earphone SOMIC CD-2688M.V N/A N/A

5 Walkman GLXIN QL-7006 N/A Battery

6 USB Mouse DELL MO56UOA GOQ02414 Power by PC

7 SATA HDD&1394 HDD Seagate 9NL6M6-500 6QG05BN1 Power by adapter

8 SATA HDD&1394 HDD Seagate 9NL6M6-500 6QG0463B Power by adapter

9 Program Control

Telephone Exchange Xinlitong 104B LC138104B200400014 Non-Shielded, 1.5m

10 MacBook Apple MB061CH W8732B4TZ5V Power by adapter

11 USB Receiver msi IR603 N/A N/A

12 SD Card Kingston 1GB N/A N/A

13 Express Card APIOTEK 24in1 1 N/A

14 Antenna msi N/A N/A N/A

15 Remote Control msi RC115V N/A N/A

16 PC DELL DCMF 11DMF2X Non-Shielded, 1.8m


Page: 14 of 112

1.4. Configuration of Tested System

Connection Diagram

Signal Cable Type Signal cable Description

A HDMI Cable Shielded, 1.8m

B VGA Cable Shielded, 1.8m, with two ferrite core bonded

C Earphone & Microphone Cable Non-Shielded, 2.1m

D Earphone & Microphone Cable Non-Shielded, 2.1m

E Audio Cable Non-Shielded, 1.8m

F USB Mouse Cable Shielded, 1.8m

G E-SATA Cable Shielded, 1.0m

H 1394 Cable Shielded, 1.5m

I Antenna Cable Non-Shielded, 1.5m

J Telecom Cable Non-Shielded, >10m

K LAN Cable Non-Shielded, >10m

L Telecom Cable Non-Shielded, 1.8m


Page: 15 of 112

1.5. EUT Exercise Software

1 Setup the EUT and simulators as shown on above.

2 Turn on the power of all equipment.

3 EUT will send and receive data through LAN using “Ping” function.

4 EUT will send and receive data through Telecom using Hyper terminal program, communicate to

other Notebook by WLAN and Bluetooth.

5 Execute the HDD running BurnIn Test (Ver5.0) software, send “H” pattern to the Monitor.

6 Open the camera and play music using Media player program.


Page: 16 of 112

2. Technical Test 2.1. Summary of Test Result

No deviations from the test standards Deviations from the test standards as below description:

Emission

Performed Test Item Normative References Test Performed Deviation

Conducted disturbance at mains

terminals and telecommunication

ports

EN 55022: 2006+A1: 2007

Yes No

Radiated disturbance EN 55022: 2006+A1: 2007

Yes No

Harmonic current emissions EN 61000-3-2: 2006 Yes No

Voltage fluctuations and flicker EN 61000-3-3: 1995+A1: 2001+A2: 2005 Yes No

Immunity

Performed Test Item Normative References Test Performed Deviation

Electrostatic discharge IEC 61000-4-2: 2001 Yes No

Radio-frequency electromagnetic

field

IEC 61000-4-3: 2006 Yes No

Fast transients IEC 61000-4-4: 2004 Yes No

Surges IEC 61000-4-5: 2005 Yes No

Radio-frequency continuous

conducted

IEC 61000-4-6: 2006 Yes No

Power-frequency magnetic field IEC 61000-4-8: 2001 Yes No

Voltage dips and interruptions IEC 61000-4-11: 2004 Yes No


Page: 17 of 112

2.2. List of Test Equipment Conducted disturbance at mains terminals and telecommunication ports / SR-1 Instrument Manufacturer Model No. Serial No. Calibrated Date EMI Test Receiver R&S ESCI 100726 2009.04.23 Two-Line V-Network R&S ENV216 100013 2009.06.11 Two-Line V-Network R&S ENV216 100014 2009.04.23 Balanced Telecom ISN Fischer FCC-TLISN-T2-02 20352 2009.02.03 Balanced Telecom ISN Fischer FCC-TLISN-T4-02 20353 2009.02.03 Balanced Telecom ISN Fischer FCC-TLISN-T8-02 20354 2009.02.03 Current Probe R&S EZ-17 100255 2009.04.18 50ohm Termination SHX TF2 07081401 2008.09.28 50ohm Termination SHX TF2 07081402 2008.09.28 50ohm Termination SHX TF2 07081403 2008.09.28 50ohm Coaxial Switch Anritsu MP59B 6200464462 2008.11.24 Coaxial Cable Suhner RG 223 SR1-C1 2009.05.25 Temperature/Humidity Meter zhicheng ZC1-2 SR1-TH 2009.03.31 Radiated disturbance / AC-1 Instrument Manufacturer Model No. Serial No. Calibrated Date Spectrum Analyzer Agilent E4403B MY45102715 N/A Spectrum Analyzer Agilent E4403B MY45102798 N/A Spectrum Analyzer Agilent N9010A MY48030494 2009.04.23 EMI Test Receiver R&S ESCI 100175 2008.11.15 Preamplifier Quietek AP-025C CHM-0511006 2009.05.25 Preamplifier Quietek AP-025C CHM-0609028 2009.05.25 Preamplifier Quietek AP-180C CHM-0602013 2009.05.25 Bilog Antenna Schaffner CBL6112B 2933 2008.11.21 Bilog Antenna Schaffner CBL6112B 2931 2008.11.21 Broad-Band Horn Antenna Schwarzbeck BBHA9120D 499 2009.06.11 50ohm Coaxial Switch Anritsu MP59B 6200447303 2008.11.24 50ohm Coaxial Switch Anritsu MP59B 6200464461 2008.11.24 50ohm Coaxial Switch Anritsu MP59B 6200447305 2008.11.24 Coaxial Cable Huber+Suhner SUCOFLEX 106 AC1-L 2009.05.25 Coaxial Cable Huber+Suhner SUCOFLEX 106 AC1-R 2009.05.25 Coaxial Cable Huber+Suhner SUCOFLEX 106 AC1-C 2009.05.25 Temperature/Humidity Meter zhicheng ZC1-2 AC1-TH 2009.03.31 Radiated disturbance / AC-2 Instrument Manufacturer Model No. Serial No. Calibrated Date EMI Test Receiver R&S ESCI 100573 2009.04.23 Bilog Antenna Teseq GmbH CBL6112D 27611 2009.02.25 Coaxial Cable Huber+Suhner SUCOFLEX 106 AC2-C 2009.05.25 Temperature/Humidity Meter zhicheng ZC1-2 AC2-TH 2009.03.31 Radiated disturbance / AC-3 Instrument Manufacturer Model No. Serial No. Calibrated Date EMI Test Receiver R&S ESCI 100176 2008.11.15 Bilog Antenna Teseq GmbH CBL6112D 27613 2009.02.25 Coaxial Cable Huber+Suhner SUCOFLEX 106 AC3-C 2009.05.25 Temperature/Humidity Meter zhicheng ZC1-2 AC3-TH 2009.03.31 Radiated disturbance / AC-5 Instrument Manufacturer Model No. Serial No. Calibrated Date Spectrum Analyzer Agilent N9010A MY48030494 2009.04.23


Page: 18 of 112

EMI Test Receiver R&S ESCI 100906 2009.02.16 Preamplifier Quietek AP-180C CHM-0602013 2009.05.25 Bilog Antenna Teseq GmbH CBL6112D 27612 2009.02.25 Broad-Band Horn Antenna Schwarzbeck BBHA9120D 499 2009.06.11 Coaxial Cable Huber+Suhner SUCOFLEX 106 AC5-C1 2009.05.25 Temperature/Humidity Meter zhicheng ZC1-2 AC5-TH 2009.03.31 Harmonic current emissions / SR-1 Instrument Manufacturer Model No. Serial No. Calibrated Date Power Analyzer California PACS-1 72419 2008.11.18 AC Power Source California 5001iX-208 56741 2008.11.18 Temperature/Humidity Meter zhicheng ZC1-2 SR1-TH 2009.03.31 Voltage fluctuation and flicker / SR-1 Instrument Manufacturer Model No. Serial No. Calibrated Date Power Analyzer California PACS-1 72419 2008.11.18 AC Power Source California 5001iX-208 56741 2008.11.18 Temperature/Humidity Meter zhicheng ZC1-2 SR1-TH 2009.03.31 Electrostatic discharge / SR-3 Instrument Manufacturer Model No. Serial No. Calibrated Date ESD Simulator EM TEST Dito V0616101367 2009.08.07 ESD Simulator EMC PARTNER ESD3000DN1 140 2009.05.05 Barometer Fengyun DYM3 0506048 2008.12.07 Temperature/Humidity Meter zhicheng ZC1-2 SR3-TH 2009.03.31 Radio-frequency electromagnetic field / AC-4 Instrument Manufacturer Model No. Serial No. Calibrated Date Signal Generator R&S SML03 102324 2008.10.21 Power Meter Boonton 4231A 144502 2008.10.21 Power Sensor Boonton 51011-EMC 33859 2008.10.21 RF Switch Network Schaffner RFS N100 21799 N/A Power Amplifier Schaffner CBA9413B 43526 NA Power Amplifier Schaffner CBA9428 43516 NA Directional Coupler Schaffner CHA 9652B 0121 N/A Directional Coupler A&R DC7144A 312249 N/A Electric Field Probe Type 8.3 narda 2244/90.21 AZ-0030 2009.06.11 Electromagnetic Radiation Meter

narda 2244/70 AW-0074 2009.06.11

Bilog Antenna Schaffner CBL6141A 4278 N/A Horn Antenna A&R AT4002A 312312 N/A Temperature/Humidity Meter Zhicheng ZC1-2 AC4-TH 2009.03.31 Fast transients / SR-2 Instrument Manufacturer Model No. Serial No. Calibrated Date Immunity Test System KeyTek EMCpro PLUS 508273 2009.04.23 CCL KeyTek CCL 0510181 2009.04.23 Temperature/Humidity Meter zhicheng ZC1-2 SR2-TH 2009.03.31


Page: 19 of 112

Surges / SR-2 Instrument Manufacturer Model No. Serial No. Calibrated Date Immunity Test System KeyTek EMCpro PLUS 508273 2009.04.23 Coupler/Decoupler Telecom Line

KeyTek CM-TELCD 0506277 N/A

Coupler/Decoupler Signal Line

KeyTek CM-I/OCD 0508206 N/A

Temperature/Humidity Meter zhicheng ZC1-2 SR2-TH 2009.03.31 Radio-frequency continuous conducted / SR-2 Instrument Manufacturer Model No. Serial No. Calibrated Date RF-Generator Schaffner NSG2070 1120 2008.11.12 Attenuator Schaffner INA2070-1 2120 2008.11.12 Coupling / Decoupling Network

Schaffner CDN M016 21249 2008.11.12

Coupling / Decoupling Network

Teseq GmbH CDN M016 24484 2008.09.03


Schaffner CDN T400 19083 2008.11.12


Teseq GmbH CDN T400 22461 2008.09.03


Teseq GmbH CDN T800 26167 2009.09.03

Temperature/Humidity Meter zhicheng ZC1-2 SR2-TH 2009.03.31 Power-frequency magnetic field / SR-2 Instrument Manufacturer Model No. Serial No. Calibrated Date Immunity Test System KeyTek EMCpro PLUS 508273 2009.04.23 CM-HCOIL H-Field Loop KeyTek F-1000-4-8/9/10-L-1M 05016 2009.04.23 Temperature/Humidity Meter zhicheng ZC1-2 SR2-TH 2009.03.31 Voltage dips and interruptions / SR-2 Instrument Manufacturer Model No. Serial No. Calibrated Date Immunity Test System KeyTek EMCpro PLUS 508273 2009.04.23 Temperature/Humidity Meter zhicheng ZC1-2 SR2-TH 2009.03.31


Page: 20 of 112

2.3. Measurement Uncertainty

Conducted disturbance at mains terminals and telecommunication ports

The maximum measurement uncertainty is evaluated as ± 3.48dB.

Radiated disturbance

The maximum measurement uncertainty is evaluated as ± 4.27dB.

Harmonic current emissions The maximum measurement uncertainty is evaluated as ± 0.2%.

Voltage fluctuation and flicker The maximum measurement uncertainty is evaluated as dc and dmax: ± 0.095%, Pst and Plt: ± 4%, d(t): ± 1.5%

Electrostatic discharge The maximum measurement uncertainty is evaluated as Voltage: ± 1.63%, Time: ± 2.76%.

Radio-frequency electromagnetic field The maximum measurement uncertainty is evaluated as ± 2.72dB.

Fast transients The maximum measurement uncertainty is evaluated as Voltage: ± 1.63%, Frequency: ± 2.8 x 10-10, Time: ± 2.76%.

Surges The maximum measurement uncertainty is evaluated as Voltage: ± 1.63%, Time: ± 2.76%.

Radio-frequency continuous conducted The maximum measurement uncertainty is evaluated as ± 3.72dB.

Power-frequency magnetic field The maximum measurement uncertainty is evaluated as ± 2.0%.

Voltage dips and interruptions The maximum measurement uncertainty is evaluated as Voltage: ± 1.63%, Time: ± 2.76%.


Page: 21 of 112

2.4. Performance Criteria Performance Criterion A The equipment shall continue to operate as intended without operator intervention. No degradation of performance or loss of function is allowed below a performance level specified by the anufacturer when the equipment is used as intended. The performance level may be replaced by a permissible loss of performance. If the minimum performance level or the permissible performance loss is not specified by the manufacturer, then either of these may be derived from the product description and documentation, and by what the user may reasonably expect from the equipment if used as ntended. Performance Criterion B After the test, the equipment shall continue to operate as intended without operator intervention. No degradation of performance or loss of function is allowed, after the application of the phenomena below a performance level specified by the manufacturer, when the equipment is used as intended. The performance level may be replaced by a permissible loss of performance. During the test, degradation of performance is allowed. However, no change of operating state or stored data is allowed to persist after the test. If the minimum performance level (or the permissible performance loss) is not specified by the manufacturer, then either of these may be derived from the product description and documentation, and by what the user may reasonably expect from the equipment if used as intended. Performance Criterion C Loss of function is allowed, provided the function is self-recoverable, or can be restored by the operation of the controls by the user in accordance with the manufacturer’s instructions. Functions, and/or information stored in non-volatile memory, or protected by a battery backup, shall not be lost.


Page: 22 of 112

3. Conducted disturbance at mains terminals and telecommunication ports

3.1. Test Specification

According to EMC Standard: EN 55022

3.2. Test Setup

3.3. Limit Limits of mains terminal disturbance voltage

Limits for conducted disturbance at the mains ports of class A ITE

Limits dB(μV) Frequency range

MHz Quasi-peak Average

0.15 to 0.50 79 66

0.50 to 30 73 60

NOTE: The lower limit shall apply at the transition frequency.

Limits for conducted disturbance at the mains ports of class B ITE

Limits dB(μV) Frequency range

MHz Quasi-peak Average


Page: 23 of 112

0.15 to 0.50 66 to 56 56 to 46

0.50 to 5 56 46

5 to 30 60 50

NOTE 1: The lower limit shall apply at the transition frequencies. NOTE 2: The limit decreases linearly with the logarithm of the frequency in the range 0.15MHz to 0.50MHz. Limits of conducted common mode (asymmetric mode) disturbance at telecommunication ports

Limits of conducted common mode (asymmetric mode) disturbance at telecommunication ports in the frequency range 0.15MHz to 30 MHz for class A equipment

Voltage Limits dB(μV)

Current limits dB(μA) Frequency range

MHz Quasi-peak Average Quasi-peak Average

0.15 to 0.50 97 to 87 84 to 74 53 to 43 40 to 30

0.50 to 30 87 74 43 30

NOTE 1: The limits decrease linearly with the logarithm of the frequency in the range 0.15MHz to 0.5MHz. NOTE 2: The current and voltage disturbance limits are derived for use with an impedance stabilization network (ISN) which presents a common mode (asymmetric mode) impedance of 150Ω to the telecommunication port under test (conversion factor is 20 log10150 / I = 44dB).

Limits of conducted common mode (asymmetric mode) disturbance at telecommunication ports in the frequency range 0.15MHz to 30 MHz for class B equipment

Voltage Limits dB(μV)

Current limits dB(μA) Frequency range

MHz Quasi-peak Average Quasi-peak Average

0.15 to 0.50 84 to 74 74 to 64 40 to 30 30 to 20

0.50 to 30 74 64 30 20

NOTE 1: The limits decrease linearly with the logarithm of the frequency in the range 0.15MHz to 0.5MHz. NOTE 2: The current and voltage disturbance limits are derived for use with an impedance stabilization network (ISN) which presents a common mode (asymmetric mode) impedance of 150Ω to the telecommunication port under test (conversion factor is 20 log10150 / I = 44dB).

3.4. Test Procedure


Page: 24 of 112

For Main Ports: The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50Ω / 50μH or 50Ω / 50μH + 5Ω coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 50Ω / 50μH or 50Ω / 50μH + 5Ω coupling mpedance with 50Ω termination. Both sides of A.C. line are checked for maximum conducted interference. Conducted emissions were invested over the frequency range from 0.15MHz to 30MHz using a receiver bandwidth of 9kHz. For Telecommunication Ports:

The mains voltage shall be supplied to the EUT via the LISN when the measurement of telecommunication port is performed. The common mode disturbances at the telecommunication port shall be connected to the ISN, which is 150Ω impedance. Both alternative cables are tested related to the LCL requested. Conducted emissions were invested over the frequency range from 0.15MHz to 30MHz using a receiver bandwidth of 9kHz.

3.5. Deviation from Test Standard No deviation.


Page: 25 of 112

3.6. Test Result Engineer : Nike

Site : SR-1 (Conducted Emission and Power

Disturbance Test)

Time : 2009/08/23 - 15:12

Limit : EN55022_B_00M_QP Margin : 10

EUT : NOTEBOOK Probe : ENV216_100014(0.009-30MHz) - Line1

Power : AC 230V/50Hz Note : Mode 1: LCD (1680*1050@60Hz) + VGA

(1680*1050@60Hz)


Page: 26 of 112

Engineer : Nike


Disturbance Test)

Time : 2009/08/23 - 15:12




(1680*1050@60Hz)

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.170 10.006 33.800 43.806 -21.154 64.960 QUASIPEAK

2 0.262 9.469 27.300 36.769 -24.599 61.368 QUASIPEAK

3 * 0.434 9.583 29.400 38.983 -18.193 57.176 QUASIPEAK

4 0.990 9.730 24.700 34.430 -21.570 56.000 QUASIPEAK

5 1.194 9.720 24.300 34.020 -21.980 56.000 QUASIPEAK

6 11.902 10.070 22.600 32.670 -27.330 60.000 QUASIPEAK

Note: 1. All Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor.


Page: 27 of 112

Engineer : Nike


Disturbance Test)

Time : 2009/08/23 - 15:12

Limit : EN55022_B_00M_AV Margin : 0



(1680*1050@60Hz)

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.170 10.006 28.500 38.506 -16.454 54.960 AVERAGE

2 0.262 9.469 20.300 29.769 -21.599 51.368 AVERAGE

3 0.434 9.583 19.900 29.483 -17.693 47.176 AVERAGE

4 0.990 9.730 17.600 27.330 -18.670 46.000 AVERAGE

5 1.194 9.720 18.100 27.820 -18.180 46.000 AVERAGE

6 11.902 10.070 18.000 28.070 -21.930 50.000 AVERAGE



Page: 28 of 112

Engineer : Nike


Disturbance Test)

Time : 2009/08/23 - 15:22


EUT : NOTEBOOK Probe : ENV216_100014(0.009-30MHz) – Line2


(1680*1050@60Hz)


Page: 29 of 112

Engineer : Nike


Disturbance Test)

Time : 2009/08/23 - 15:22




(1680*1050@60Hz)

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.234 9.580 31.000 40.580 -21.727 62.307 QUASIPEAK

2 * 0.438 9.613 30.700 40.313 -16.787 57.100 QUASIPEAK

3 0.562 9.663 27.500 37.163 -18.837 56.000 QUASIPEAK

4 1.230 9.750 24.300 34.050 -21.950 56.000 QUASIPEAK

5 3.566 9.700 21.500 31.200 -24.800 56.000 QUASIPEAK

6 11.178 9.930 24.200 34.130 -25.870 60.000 QUASIPEAK



Page: 30 of 112

Engineer : Nike


Disturbance Test)

Time : 2009/08/23 - 15:22

Limit : EN55022_B_00M_AV Margin : 0



(1680*1050@60Hz)

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.234 9.580 17.500 27.080 -25.227 52.307 AVERAGE

2 0.438 9.613 19.200 28.813 -18.287 47.100 AVERAGE

3 0.562 9.663 18.600 28.263 -17.737 46.000 AVERAGE

4 * 1.230 9.750 19.800 29.550 -16.450 46.000 AVERAGE

5 3.566 9.700 17.200 26.900 -19.100 46.000 AVERAGE

6 11.178 9.930 19.500 29.430 -20.570 50.000 AVERAGE



Page: 31 of 112

Engineer : Rove


Disturbance Test)

Time : 2009/09/04 - 02:15

Limit : ISN_Voltage_B_00M_QP Margin : 10

EUT : Notebook Probe : FCC-TLISN-T4_20353(0.15-30MHz) - Line1


(1680*1050@60Hz) for LAN – 10Mbps


Page: 32 of 112

Engineer : Rove


Disturbance Test)

Time : 2009/09/04 - 02:17




(1680*1050@60Hz) for LAN – 10Mbps

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 1.302 9.790 41.800 51.590 -22.410 74.000 QUASIPEAK

2 * 7.558 9.880 46.400 56.280 -17.720 74.000 QUASIPEAK

3 9.078 9.880 44.600 54.480 -19.520 74.000 QUASIPEAK

4 11.086 9.910 41.600 51.510 -22.490 74.000 QUASIPEAK

5 11.850 9.920 41.800 51.720 -22.280 74.000 QUASIPEAK

6 13.754 9.940 43.900 53.840 -20.160 74.000 QUASIPEAK



Page: 33 of 112

Engineer : Rove


Disturbance Test)

Time : 2009/09/04 - 02:17

Limit : ISN_Voltage_B_00M_AV Margin : 0



(1680*1050@60Hz) for LAN – 10Mbps

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 1.302 9.790 37.200 46.990 -17.010 64.000 AVERAGE

2 * 7.558 9.880 39.800 49.680 -14.320 64.000 AVERAGE

3 9.078 9.880 34.000 43.880 -20.120 64.000 AVERAGE

4 11.086 9.910 35.600 45.510 -18.490 64.000 AVERAGE

5 11.850 9.920 35.800 45.720 -18.280 64.000 AVERAGE

6 13.754 9.940 37.000 46.940 -17.060 64.000 AVERAGE



Page: 34 of 112

Engineer : Rove


Disturbance Test)

Time : 2009/09/04 - 02:20




(1680*1050@60Hz) for LAN – 100Mbps


Page: 35 of 112

Engineer : Rove


Disturbance Test)

Time : 2009/09/04 - 02:21




(1680*1050@60Hz) for LAN – 100Mbps

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 13.358 9.930 47.900 57.830 -16.170 74.000 QUASIPEAK

2 * 16.230 9.970 50.100 60.070 -13.930 74.000 QUASIPEAK

3 17.694 9.990 49.900 59.890 -14.110 74.000 QUASIPEAK

4 18.242 9.990 49.600 59.590 -14.410 74.000 QUASIPEAK

5 19.710 10.010 48.600 58.610 -15.390 74.000 QUASIPEAK

6 20.258 10.010 48.300 58.310 -15.690 74.000 QUASIPEAK



Page: 36 of 112

Engineer : Rove


Disturbance Test)

Time : 2009/09/04 - 02:21




(1680*1050@60Hz) for LAN – 100Mbps

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 13.358 9.930 47.100 57.030 -6.970 64.000 AVERAGE

2 * 16.230 9.970 49.400 59.370 -4.630 64.000 AVERAGE

3 17.694 9.990 49.200 59.190 -4.810 64.000 AVERAGE

4 18.242 9.990 48.700 58.690 -5.310 64.000 AVERAGE

5 19.710 10.010 48.000 58.010 -5.990 64.000 AVERAGE

6 20.258 10.010 47.500 57.510 -6.490 64.000 AVERAGE



Page: 37 of 112

Engineer : Rove


Disturbance Test)

Time : 2009/09/04 - 02:24




(1680*1050@60Hz) for LAN – 1000Mbps


Page: 38 of 112

Engineer : Rove


Disturbance Test)

Time : 2009/09/04 - 02:26




(1680*1050@60Hz) for LAN – 1000Mbps

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.862 9.800 41.300 51.100 -22.900 74.000 QUASIPEAK

2 0.930 9.799 39.700 49.499 -24.501 74.000 QUASIPEAK

3 1.018 9.790 37.900 47.690 -26.310 74.000 QUASIPEAK

4 1.074 9.780 41.800 51.580 -22.420 74.000 QUASIPEAK

5 * 1.294 9.760 42.600 52.360 -21.640 74.000 QUASIPEAK

6 1.774 9.750 38.100 47.850 -26.150 74.000 QUASIPEAK



Page: 39 of 112

Engineer : Rove


Disturbance Test)

Time : 2009/09/04 - 02:26




(1680*1050@60Hz) for LAN – 1000Mbps

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.862 9.800 39.000 48.800 -15.200 64.000 AVERAGE

2 0.930 9.799 39.600 49.399 -14.601 64.000 AVERAGE

3 1.018 9.790 35.600 45.390 -18.610 64.000 AVERAGE

4 1.074 9.780 40.300 50.080 -13.920 64.000 AVERAGE

5 * 1.294 9.760 41.800 51.560 -12.440 64.000 AVERAGE

6 1.774 9.750 35.300 45.050 -18.950 64.000 AVERAGE



Page: 40 of 112

Engineer : Rove


Disturbance Test)

Time : 2009/09/04 - 02:11




(1680*1050@60Hz) for Telecom


Page: 41 of 112

Engineer : Rove


Disturbance Test)

Time : 2009/09/04 - 02:13





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 0.898 9.800 43.100 52.900 -21.100 74.000 QUASIPEAK

2 1.182 9.780 36.900 46.680 -27.320 74.000 QUASIPEAK

3 1.286 9.779 37.700 47.479 -26.521 74.000 QUASIPEAK

4 1.474 9.780 40.600 50.380 -23.620 74.000 QUASIPEAK

5 * 1.770 9.760 43.900 53.660 -20.340 74.000 QUASIPEAK

6 2.374 9.760 38.100 47.860 -26.140 74.000 QUASIPEAK



Page: 42 of 112

Engineer : Rove


Disturbance Test)

Time : 2009/09/04 - 02:13





Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV)

Margin

(dB)

Limit

(dBuV)

Detector Type

1 * 0.898 9.800 40.600 50.400 -13.600 64.000 AVERAGE

2 1.182 9.780 33.500 43.280 -20.720 64.000 AVERAGE

3 1.286 9.779 34.000 43.779 -20.221 64.000 AVERAGE

4 1.474 9.780 36.400 46.180 -17.820 64.000 AVERAGE

5 1.770 9.760 37.800 47.560 -16.440 64.000 AVERAGE

6 2.374 9.760 33.600 43.360 -20.640 64.000 AVERAGE



Page: 43 of 112

3.7. Test Photograph Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Front View of Conducted disturbance at mains terminals Test Setup

Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Side View of Conducted disturbance at mains terminals Test Setup


Page: 44 of 112

Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Front View of Conducted disturbance at telecommunication ports Test Setup (LAN)

Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Side View of Conducted disturbance at telecommunication ports Test Setup (LAN)


Page: 45 of 112

Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Front View of Conducted disturbance at telecommunication ports Test Setup (Telecom)

Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Side View of Conducted disturbance at telecommunication ports Test Setup (Telecom)


Page: 46 of 112

4. Radiated disturbance


According to EMC Standard: EN 55022

4.2. Test Setup Below 1GHz Test Setup

Above 1GHz Test Setup


Page: 47 of 112

4.3. Limit Limits below 1GHz

Limits for radiated disturbance of class A ITE at a measuring distance of 10m

Frequency range MHz

Quasi-peak limis dB(μV/m)

30 to 230 40

230 to 1000 47

NOTE 1: The lower limit shall apply at the transition frequency. NOTE 2: Additional provisions may be required for cases where interference occurs.

Limits for radiated disturbance of class B ITE at a measuring distance of 10m

Frequency range MHz

Quasi-peak limis dB(μV/m)

30 to 230 30

230 to 1000 37

NOTE 1: The lower limit shall apply at the transition frequency. NOTE 2: Additional provisions may be required for cases where interference occurs. Limits above 1GHz

Limits for radiated disturbance of class A ITE at a measuring distance of 3m

Frequency range GHz

Average limit dB(μV/m)

Peak-peak dB(μV/m)

1 to 3 56 76

3 to 6 60 80

NOTE: The lower limit applies at transition frequency.

Limits for radiated disturbance of class B ITE at a measuring distance of 3m

Frequency range GHz

Average limit dB(μV/m)

Peak-peak dB(μV/m)

1 to 3 50 70

3 to 6 54 74

NOTE: The lower limit applies at transition frequency.


Page: 48 of 112

4.4. Test Procedure The EUT and its simulators are placed on a turntable which is 0.8 meter above ground. The turntable can rotate 360 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 10 meters for below 1GHz and 3 meters for above 1GHz. The antenna can move up and down between 1 meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be changed during radiated measurement.

The bandwidth below 1GHz setting on the reveiver is 120kHz and above 1GHz is 1MHz. Conditional testing procedure: The highest internal source of an EUT is defined as the highest frequency generated or used within the EUT or on which the EUT operates or tunes. If the highest frequency of the internal sources of the EUT is less than 108 MHz, the measurement shall only be made up to 1 GHz. If the highest frequency of the internal sources of the EUT is between 108 MHz and 500 MHz, the measurement shall only be made up to 2 GHz. If the highest frequency of the internal sources of the EUT is between 500 MHz and 1 GHz, the measurement shall only be made up to 5 GHz. If the highest frequency of the internal sources of the EUT is above 1 GHz, the measurement shall be made up to 5 times the highest frequency or 6 GHz, whichever is less.



Page: 49 of 112

4.6. Test Result Engineer : Nike

Site : AC-1 (10m Semi-Anechoic Chamber) Time : 2009/08/28 - 14:02


EUT : Notebook Probe : CBL6112B_2931(30-1000MHz) - HORIZONTAL


(1680*1050@60Hz)

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)

Detector Type Ant Pos

(cm)

Table Pos

(deg)

1 61.525 -26.995 46.006 19.011 -10.989 30.000 QUASIPEAK 400.000 122.600

2 100.325 -21.595 40.589 18.994 -11.006 30.000 QUASIPEAK 400.000 226.500

3 190.050 -22.960 45.067 22.107 -7.893 30.000 QUASIPEAK 375.200 155.100

4 228.850 -21.440 43.928 22.488 -7.512 30.000 QUASIPEAK 286.400 204.300

5 413.150 -12.830 43.610 30.780 -6.220 37.000 QUASIPEAK 208.100 165.400

6 * 599.875 -9.455 40.772 31.317 -5.683 37.000 QUASIPEAK 274.200 144.300

Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor


Page: 50 of 112

Engineer : Nike



EUT : Notebook Probe : CBL6112B_2933(30-1000MHz) - VERTICAL


(1680*1050@60Hz)

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)


(cm)

Table Pos

(deg)

1 76.075 -25.905 47.050 21.145 -8.855 30.000 QUASIPEAK 100.000 256.400

2 105.175 -20.650 43.262 22.612 -7.388 30.000 QUASIPEAK 100.000 126.300

3 190.050 -22.620 44.389 21.769 -8.231 30.000 QUASIPEAK 151.200 149.400

4 342.825 -15.160 43.058 27.898 -9.102 37.000 QUASIPEAK 100.000 305.300

5 398.600 -13.620 41.110 27.490 -9.510 37.000 QUASIPEAK 100.000 226.100

6 * 675.050 -9.150 39.089 29.939 -7.061 37.000 QUASIPEAK 267.200 105.100

Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor


Page: 51 of 112

Engineer : Nike


Limit : EN55022_B_(Above_1G)_03M_PK Margin : 0

EUT : NOTEBOOK Probe : 9120D_499(1-18GHz) - HORIZONTAL


(1680*1050@60Hz)

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)


(cm)

Table Pos

(deg)

1 1575.000 -9.023 59.908 50.885 -19.115 70.000 PEAK 100.000 305.300

2 1755.000 -8.911 56.548 47.636 -22.364 70.000 PEAK 100.000 226.100

3 * 2130.000 -6.138 58.117 51.979 -18.021 70.000 PEAK 267.200 105.100

Note: 1. All Readings below 1GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. " * ", means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied.


Page: 52 of 112

Engineer : Nike


Limit : EN55022_B_(Above_1G)_03M_AV Margin : 0

EUT : NOTEBOOK Probe : 9120D_499(1-18GHz) - HORIZONTAL


(1680*1050@60Hz)

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)


(cm)

Table Pos

(deg)

1 1570.000 -9.029 34.660 25.631 -24.369 50.000 AVERAGE 100.000 305.300

2 1765.000 -8.918 39.428 30.510 -19.490 50.000 AVERAGE 100.000 226.100

3 * 2130.000 -6.138 39.317 33.179 -16.821 50.000 AVERAGE 267.200 105.100



Page: 53 of 112

Engineer : Nike


Limit : EN55022_B_(Above_1G)_03M_PK Margin : 0

EUT : NOTEBOOK Probe : 9120D_499(1-18GHz) - VERTICAL


(1680*1050@60Hz)

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)


(cm)

Table Pos

(deg)

1 1565.000 -9.034 64.423 55.388 -14.612 70.000 PEAK 100.000 313.300

2 1760.000 -8.915 60.571 51.656 -18.344 70.000 PEAK 100.000 175.600

3 * 2170.000 -5.911 64.124 58.213 -11.787 70.000 PEAK 100.000 168.200



Page: 54 of 112

Engineer : Nike


Limit : EN55022_B_(Above_1G)_03M_AV Margin : 0

EUT : NOTEBOOK Probe : 9120D_499(1-18GHz) - VERTICAL


(1680*1050@60Hz)

Frequency

(MHz)

Correct Factor

(dB)

Reading Level

(dBuV)

Measure Level

(dBuV/m)

Margin

(dB)

Limit

(dBuV/m)


(cm)

Table Pos

(deg)

1 1568.000 -9.031 40.102 31.071 -18.929 50.000 AVERAGE 100.000 313.300

2 1758.600 -8.914 41.200 32.286 -17.714 50.000 AVERAGE 100.000 175.600

3 * 2168.200 -5.920 46.300 40.380 -9.620 50.000 AVERAGE 100.000 168.200



Page: 55 of 112

4.7. Test Photograph Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Front View of Radiated disturbance Test Setup (Below 1GHz)

Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Rear View of Radiated disturbance Test Setup (Below 1GHz)


Page: 56 of 112

Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Front View of Radiated disturbance Test Setup (Above 1GHz)

Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Rear View of Radiated disturbance Test Setup (Above 1GHz)


Page: 57 of 112

5. Harmonic current emissions


According to EMC Standard: EN 61000-3-2

5.2. Test Setup

5.3. Limit (a) Limits of Class A Harmonics Currents

Harmonics Order

n

Maximum Permissible harmonic current

A

Harmonics Order

n


A

Odd harmonics Even harmonics

3 2.30 2 1.08

5 1.14 4 0.43

7 0.77 6 0.30

9 0.40 8 ≤ n ≤ 40 0.23 * 8/n

11 0.33

13 0.21

15 ≤ n ≤ 39 0.15 * 15/n


Page: 58 of 112

(b) Limits of Class B Harmonics Currents

For Class B equipment, the harmonic of the input current shall not exceed the maximum permissible values given in table that is the limit of Class A multiplied by a factor of 1.5.

(c) Limits of Class C Harmonics Currents

Harmonics Order

n

Maximum Permissible harmonic current Expressed as a percentage of the input current at the fundamental frequency

%

2 2

3 30．λ＊

5 10

7 7

9 5

11 ≤ n ≤ 39 (odd harmonics only)

3

＊λ is the circuit power factor

(d) Limits of Class D Harmonics Currents

Harmonics Order

n

Maximum Permissible harmonic current per watt

mA/W


A

3 3.4 2.30

5 1.9 1.14

7 1.0 0.77

9 0.5 0.40

11 0.35 0.33

11 ≤ n ≤ 39 (odd harmonics only)

3.85/n See limit of Class A


Page: 59 of 112

5.4. Test Procedure

The EUT is supplied in series with power analyzer from a power source having the same normal voltage and frequency as the rated supply voltage and the equipment under test. And the rated voltage at the supply voltage of EUT of 0.94 times and 1.06 times shall be performed.



Page: 60 of 112

5.6. Test Result Test Mode Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz)

Test Site SR-1 Date of Test 2009.09.01

Temperature 25°C Humidity 48%RH Barometric Pressure

101kPa Test Engineer Allen

Test Result: Pass Source qualification: Normal

Current & voltage waveforms

-0.9-0.6-0.30.00.30.60.9

-300-200-1000100200300

Cur

rent

(Am

ps)

Voltage (V

olts)

Harmonics and Class D limit line European Limits

0.000.050.100.150.200.250.300.350.400.45

Cur

rent

RM

S(A

mps

)

Harmonic #4 8 12 16 20 24 28 32 36 40

Test result: Pass


Page: 61 of 112

Test Result: Pass Source qualification: Normal THC(A): 0.14 I-THD(%): 38.84 POHC(A): 0.018 POHC Limit(A): 0.040 Highest parameter values during test:

V_RMS (Volts): 229.99 Frequency(Hz): 50.00 I_Peak (Amps): 0.839 I_RMS (Amps): 0.444 I_Fund (Amps): 0.383 Crest Factor: 2.067 Power (Watts): 93.0 Power Factor: 0.911

Harm# Harms(avg) 100%Limit %of Limit Harms(max) 150%Limit %of Limit Status 2 0.000 3 0.136 0.316 43.0 0.138 0.432 31.93 Pass 4 0.000 5 0.031 0.177 17.8 0.032 0.241 13.27 Pass 6 0.000 7 0.007 0.093 7.9 0.010 0.129 7.85 Pass 8 0.000 9 0.021 0.047 46.0 0.022 0.063 34.25 Pass 10 0.000 11 0.010 0.033 29.3 0.010 0.044 21.99 Pass 12 0.000 13 0.005 0.028 17.9 0.005 0.038 13.76 Pass 14 0.000 15 0.006 0.024 26.3 0.008 0.033 22.97 Pass 16 0.000 17 0.005 0.021 25.4 0.006 0.029 19.95 Pass 18 0.000 19 0.004 0.019 20.8 0.005 0.026 18.73 Pass 20 0.000 21 0.006 0.017 34.5 0.006 0.024 26.42 Pass 22 0.000 23 0.009 0.016 59.8 0.010 0.022 46.61 Pass 24 0.000 25 0.004 0.014 25.2 0.005 0.021 22.70 Pass 26 0.000 27 0.004 0.013 30.7 0.005 0.018 24.58 Pass 28 0.000 29 0.007 0.012 54.7 0.007 0.017 42.88 Pass 30 0.000 31 0.007 0.012 57.4 0.008 0.016 52.09 Pass 32 0.000 33 0.005 0.011 49.9 0.006 0.015 41.09 Pass 34 0.000 35 0.004 0.010 34.3 0.004 0.014 26.67 Pass 36 0.000 37 0.004 0.010 41.0 0.004 0.013 30.93 Pass 38 0.000 39 0.003 0.009 35.3 0.005 0.013 36.56 Pass 40 0.000

1. Dynamic limits were applied for this test. The highest harmonics values in the above table may not

occur at the same window as the maximum harmonics/limit ratio.

2. According to EN61000-3-2 paragraph 7 the note 1 and 2 are valid for all applications having an active

input power >75W. Others the result should be pass.


Page: 62 of 112

5.7. Test Photograph Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Harmonic current emissions Test Setup


Page: 63 of 112

6. Voltage fluctuations and flicker


According to EMC Standard: EN 61000-3-3

6.2. Test Setup

6.3. Limit The following limits apply: － the value of Pst shall not be greater than 1.0; － the value of Plt shall not be greater than 0.65; － the value of d(t) during a voltage change shall not exceed 3.3% for more than 500ms; － the relative steady-state voltage change, dc, shall not exceed 3.3%; － the maximum relative voltage change, dmax, shall not exceed;

a) 4% without additional conditions; b) 6% for equipment which is: － switched manually, or － switched automatically more frequently than twice per day, and also has either a delayed

restart (the delay being not less than a few tens of seconds), or manual restart, after a power supply interruption.

NOTE: The cycling frequency will be further limited by the Pst and P1t limit. For example: a dmax of 6% producing a rectangular voltage change characteristic twice per hour will give a P1t of about 0.65.


Page: 64 of 112

c) 7% for equipment which is: － attended whilst in use (for example: hair dryers, vacuum cleaners, kitchen equipment such

as mixers, garden equipment such as lawn mowers, portable tools such as electric drills), or － switched on automatically, or is intended to be switched on manually, no more than twice

per day, and also has either a delayed restart (the delay being not less than a few tens of seconds) or manual restart, after a power supply interruption.

Pst and P1t requirements shall not be applied to voltage changes caused by manual switching.

6.4. Test Procedure The EUT is supplied in series with power analyzer from a power source having the same normal voltage and frequency as the rated supply voltage and the equipment under test. And the rated voltage at the supply voltage of EUT of 0.94 times and 1.06 times shall be performed.



Page: 65 of 112



Temperature 25°C Humidity 48%RH Barometric Pressure 101kPa Test Engineer Allen

Test Result: Pass Status: Test Completed

Psti and limit line European Limits

0.25

0.50

0.75

1.00

Pst

7:36:12

Plt and limit line

0.00.10.20.30.40.50.6

Plt

7:36:12

Parameter values recorded during the test: Vrms at the end of test (Volt): 229.83 Highest dt (%): 0.00 Test limit (%): 3.30 Pass Time(mS) > dt: 0.0 Test limit (mS): 0.0 Pass Highest dc (%): 0.00 Test limit (%): 3.30 Pass Highest dmax (%): 0.00 Test limit (%): 4.00 Pass Highest Pst (10 min. period): 0.064 Test limit: 1.000 Pass Highest Plt (2 hr. period): 0.028 Test limit: 0.650 Pass


Page: 66 of 112

6.7. Test Photograph Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Voltage fluctuations and flicker Test Setup


Page: 67 of 112

7. Electrostatic discharge


According to EMC Standard: IEC 61000-4-2

7.2. Test Setup

7.3. Limit

Environmental phenomenon

Test specification Units Performance criterion

Enclosure port

Electrostatic discharge

±4 (Contact discharge) ±8 (Air discharge)

kV (Charge voltage) kV (Charge voltage)

B

7.4. Test Procedure

Direct application of discharges to the EUT: Contact discharge was applied only to conductive surfaces of the EUT. Air discharges were applied only to non-conductive surfaces of the EUT. During the test, it was performed with single discharges. For the single discharge time between successive single discharges will be keep longer 1 second. It was at least ten single discharges with positive and negative at the same selected point.


Page: 68 of 112

The selected point, which was performed with electrostatic discharge, was marked on the red label of the EUT. Indirect application of discharges to the EUT: Vertical Coupling Plane (VCP): The coupling plane, of dimensions 0.5m x 0.5m, is placed parallel to, and positioned at a distance 0.1m from, the EUT, with the Discharge Electrode touching the coupling plane. The four faces of the EUT will be performed with electrostatic discharge. It was at least ten single discharges with positive and negative at the same selected point. Horizontal Coupling Plane (HCP): The coupling plane is placed under to the EUT. The generator shall be positioned vertically at a distance of 0.1m from the EUT, with the Discharge Electrode touching the coupling plane. The four faces of the EUT will be performed with electrostatic discharge. It was at least ten single discharges with positive and negative at the same selected point.



Page: 69 of 112




Air Discharge

Test Level Test Location

+2kV -2kV +4kV -4kV +8kV -8kVObservation Result

1 A A A A A A Note Pass





























Page: 70 of 112







































Page: 71 of 112


Contact Discharge


+2kV -2kV +4kV -4kV Observation Result

67 A A A A Note Pass

















Horizontal Coupling



Front A A A A Note Pass

Rear A A A A Note Pass

Left A A A A Note Pass

Right A A A A Note Pass

Vertical Coupling



Front A A A A Note Pass

Rear A A A A Note Pass

Left A A A A Note Pass


Page: 72 of 112

Right A A A A Note Pass

NOTE: There was no change compared with initial operation during the test.


Page: 73 of 112

7.7. Test Photograph Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Electrostatic discharge Test Setup


Page: 74 of 112

Electrostatic discharge Test Location


Page: 75 of 112


Page: 76 of 112


Page: 77 of 112

8. Radio-frequency electromagnetic field



8.2. Test Setup

8.3. Limit



Enclosure port

Radio-frequency electromagnetic field

80 - 1000 3 80

MHz V/m (unmodulated, r.m.s) % AM (1kHz)

A

NOTE: The frequency range is scanned as specified. However, when specified in Annex A, an additional comprehensive functional test shall be carried out at a limited number of frequencies. The selected frequencies are: 80, 120, 160, 230, 434, 460, 600, 863 and 900MHz (±1%).

8.4. Test Procedure The EUT and load, which are placed on a table that is 0.8 meter above ground, are placed with one coincident with the calibration plane such that the distance from antenna to the EUT was 3 meters. Both horizontal and vertical polarization of the antenna and four sides of the EUT are set on


Page: 78 of 112

measurement. In order to judge the EUT performance, a CCD camera is used to monitor EUT screen. All the scanning conditions are as follows:

Condition of Test Remarks

1. Field Strength 3V/m

2. Radiated Signal AM 80% Modulated with 1kHz

3. Scanning Frequency 80 - 1000MHz

4 Dwell Time 3 Seconds

5. Frequency Step Size Δ f 1%

6. The Rate of Sweep of Frequency 1.5 x 10-3 decades/s

8.5. Deviation from Test Standard

No deviation.


Page: 79 of 112


Test Site AC-4 Date of Test 2009.09.03


Frequency

(MHz) Polarity Position

Field Strength(V/m)

Complied to Criteria

Observation Result

80-1000 Horizontal Front 3 A Note Pass

80-1000 Vertical Front 3 A Note Pass

80-1000 Horizontal Rear 3 A Note Pass

80-1000 Vertical Rear 3 A Note Pass

80-1000 Horizontal Left 3 A Note Pass

80-1000 Vertical Left 3 A Note Pass

80-1000 Horizontal Right 3 A Note Pass

80-1000 Vertical Right 3 A Note Pass



Page: 80 of 112

8.7. Test Photograph Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Radio-frequency electromagnetic field Test Setup


Page: 81 of 112

9. Fast transients



9.2. Test Setup

9.3. Limit



Input a.c. power ports

Fast transients ±1.0 5/50 5

kV (peak) Tr/Th ns Repetition frequency kHz

B

Input d.c. power ports

Fast transients ±0.5 5/50 5

kV (peak) Tr/Th ns Repetition frequency kHz

B

Singal ports and telecommunication ports (See Note)

Fast transients ±0.5 5/50

kV (peak) Tr/Th ns

B


Page: 82 of 112

5 Repetition frequency kHz

NOTE: Applicable only to cables which according to the manufacturer’s specification supports communication on cable lengths greater than 3m.

9.4. Test Procedure The EUT is placed on a table that is 0.8 meter height. A ground reference plane is placed on the table, and uses a 0.1m insulation between the EUT and ground reference plane.

The minimum area of the ground reference plane is 1m*1m, and 0.65mm thick min, and projected beyond the EUT by at least 0.1m on all sides. For input a.c. and d.c. power ports: The EUT is connected to the power mains through a coupling device that directly couples the EFT/B interference signal. Each of the line conductors is impressed with burst noise for 1 minute. The length of the power lines between the coupling device and the EUT is 0.5m. For signal and telecommunication ports: The EFT interference signal is through a coupling clamp device couples to the signal of the EUT with burst noise for 1 minute. The length of the signal lines between the coupling device and the EUT is 0.5m.



Page: 83 of 112




Inject Line

Polarity Test Level

(kV) Test Duration

(second) Inject

MethodComplied to Criteria

Observation Result

L + 1 60 Direct A Note Pass

L - 1 60 Direct A Note Pass

N + 1 60 Direct A Note Pass

N - 1 60 Direct A Note Pass

PE + 1 60 Direct A Note Pass

PE - 1 60 Direct A Note Pass

L+N+PE + 1 60 Direct A Note Pass

L+N+PE - 1 60 Direct A Note Pass

LAN + 0.5 60 Clamp A Note Pass

LAN - 0.5 60 Clamp A Note Pass

Telecom + 0.5 60 Clamp A Note Pass

Telecom - 0.5 60 Clamp A Note Pass



Page: 84 of 112

9.7. Test Photograph Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Fast transients Test Setup (Input a.c. power ports)

Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Fast transients Test Setup (LAN)


Page: 85 of 112

Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Fast transients Test Setup (Telecom)


Page: 86 of 112

10. Surges



10.2. Test Setup

10.3. Limit



Input a.c. power ports (See Note 1)

Surges 1.2/50 (8/20) 1 line to line 2 line to earth (ground)

Tr/Th us kV (peak) kV (peak)

B

Input d.c. power ports (See Note 2)

Surges 1.2/50 (8/20) 0.5

Tr/Th us kV (peak)

B

Singal ports and telecommunication ports (See Note 2 and 3)

Surges Line to Ground

1.2/50 (8/20) 1

Tr/Th us kV (peak)

B

NOTE 1: When the manufacturer specifies protection measures and it is impractical to simulate these measures during the tests, then the applied test levels shall be reduced to


Page: 87 of 112

0.5kV and 1kV. NOTE 2: Applicable only to ports which according to the manufacturer’s specification mayconnect directly to outdoor cables. NOTE 3: Where normal functioning cannot be achieved because of the impact of the CDN on the EUT, no test shall be required.

10.4. Test Procedure

The EUT is placed on a table that is 0.8 meter above a metal ground plane measured 1m*1m minimum and 0.65mm thick minimum and projected beyond the EUT by at least 0.1m on all sides. The length of power cord between the coupling device and the EUT shall be 2m or less. For input a.c. and d.c. power ports: The EUT is connected to the power mains through a coupling device that directly couples the surge interference signal. The surge noise shall be applied synchronized to the voltage phase at 00, 900, 1800, 2700 and the peak value of the a.c. voltage wave. (Positive and negative) Each of Line to Earth and Line to Line is impressed with a sequence of five surge voltages with interval of 1 minute. For signal and telecommunication ports: The signal line of EUT is connected to coupling and decoupling network that directly couples the surge interference signal. Only Line to ground is impressed with a sequence of five surge voltages with interval of 1

minute.



Page: 88 of 112




Inject Line

Polarity Angle

(degree) Test Level

(kV) Test Interval

(second) Complied to Criteria

Observation Result

L+N + 0 1 60 A Note Pass

L+N - 0 1 60 A Note Pass







L+PE + 0 2 60 A Note Pass

L+PE - 0 2 60 A Note Pass







N+PE + 0 2 60 A Note Pass

N+PE - 0 2 60 A Note Pass







Telecom (Line to Ground)

+ N/A 1 60 A Note Pass

Telecom (Line to Ground)

- N/A 1 60 A Note Pass



Page: 89 of 112

10.7. Test Photograph Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Surges Test Setup (Input a.c. power ports)

Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Surges Test Setup (Telecom)


Page: 90 of 112

11. Radio-frequency continuous conducted



11.2. Test Setup CDN Test Setup

EM Clamp Test Setup


Page: 91 of 112

11.3. Limit



Input a.c. power ports (See Note 1)

Radio-frequency continuous conducted

0.15 - 80 3 80

MHz V (unmodulated, r.m.s) % AM (1kHz)

A

Input d.c. power ports (See Note 1)


0.15 - 80 3 80


A

Singal ports and telecommunication ports (See Note 1 and 3)


0.15 - 80 3 80


A

NOTE 1: The frequency range is scanned as specified. However, when specified in Annex A, an additional comprehensive functional test shall be carried out at a limited number of frequencies. The selected frequencies for conducted test are: 0.2; 1; 7.1; 13.56; 21; 27.12 and 40.68MHz (±1%). NOTE 2: Applicable only to cables which according to the manufacturer’s specification supports communication on cable lengths greater than 3m.


The EUT is placed on a table that is 0.8 meter height, and a ground reference plane on the table, EUT is placed upon table and use a 0.1m insulation between the EUT and ground reference plane. For input a.c. and d.c. power ports: The EUT is connected to the power mains through a coupling and decoupling networks for power supply lines. And directly couples the disturbances signal into EUT.

Used CDN-M2 for two wires or CDN-M3 for three wires. For signal and telecommunication ports: The disturbance signal is through a coupling and decoupling networks (CDN) or EM-clamp device couples to the signal and telecommunication lines of the EUT.


Page: 92 of 112

Condition of Test Remarks

1. Field Strength 3V

2. Radiated Signal AM 80% Modulated with 1kHz

3. Scanning Frequency 0.15 - 80MHz

4 Dwell Time 3 Seconds

5. Frequency Step Size Δ f 1%

6. The Rate of Sweep of Frequency 1.5 x 10-3 decades/s


No deviation.


Page: 93 of 112




Frequency

(MHz) Inject Voltage

(V/m) Inject Ports Inject Method

Complied to Criteria

Observation Result

0.15-80 3 AC Mains CDN A Note Pass

0.15-80 3 LAN CDN A Note Pass

0.15-80 3 Telecom CDN A Note Pass



Page: 94 of 112

11.7. Test Photograph Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Radio-frequency continuous conducted Test Setup (Input a.c. power ports)

Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Radio-frequency continuous conducted Test Setup (LAN)


Page: 95 of 112

Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Radio-frequency continuous conducted Test Setup (Telecom)


Page: 96 of 112

12. Power-frequency magnetic field



12.2. Test Setup

12.3. Limit



Enclosure port

Power-frequency magnetic field

50 1

Hz A/m (r.m.s)

A

NOTE: Applicable only to equipment containing devices susceptible to magnetic fields, such as CRT monitors, Hall elements, electrodynamic microphones, magnetic field sensors, etc.

12.4. Test Procedure The EUT is placed on a table which is 0.8 meter above a metal ground plane measured at least 1m*1m minimum. The test magnetic field shall be placed at central of the induction coil. The test magnetic Field shall be applied 10 minutes by the immersion method to the EUT, and

the induction coil shall be rotated by 90° in order to expose the EUT to the test field with different orientation (X, Y, Z Orientations).


Page: 97 of 112


No deviation.


Page: 98 of 112




Test Coil Position Frequency

(Hz) Magnetic Strength

(A/m) Complied to

Criteria Observation Result

X Axis 50 1 A Note Pass

Y Axis 50 1 A Note Pass

Z Axis 50 1 A Note Pass



Page: 99 of 112

12.7. Test Photograph Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Power-frequency magnetic field Test Setup


Page: 100 of 112

13. Voltage dips and interruptions



13.2. Test Setup

13.3. Limit



Input a.c. power ports

>95 0.5

% reduction period

B Voltage dips

30 25

% reduction periods

C

Voltage interruptions

>95 250

% reduction periods

C

NOTE: Changes to occur at 0 degree crossover point of the voltage waveform.


The EUT is placed on a table which is 0.8 meter above a metal ground plane measured 1m*1m minimum, and 0.65mm thick minimum, and projected beyond the EUT by at least 0.1m on all


Page: 101 of 112

sides. The power cord shall be used the shortest power cord as specified by the manufacturer. For Voltage dips and interruptions test: The selection of test voltage is based on the rated power range. If the operation range is large than 20% of lower power range, both end of specified voltage shall be tested. Otherwise, the typical voltage specification is selected as test voltage. The EUT is connected to the power mains through a coupling device that directly couples to the voltage dips and interruption generator.



Page: 102 of 112




Voltage

% Reduction Test Duration

(ms) Complied to

Criteria Observation Result

>95 10 A Note 1 Pass

30 500 A Note 1 Pass

>95 5000 B Note 2 Pass

NOTE 1: There was no change compared with initial operation during the test. NOET 2: The power consumption of EUT has changed from adapter to battery during the test, but self-recoverable after the test.


Page: 103 of 112

13.7. Test Photograph Test Mode: Mode 1: LCD (1680*1050@60Hz) + VGA (1680*1050@60Hz) Description: Voltage dips and interruptions Test Setup


Page: 104 of 112

14. Attachment

EUT Photograph (1) EUT Photo

(2) EUT Photo


Page: 105 of 112

(3) EUT Photo

(4) EUT Photo


Page: 106 of 112

(5) EUT Photo

(6) EUT Photo


Page: 107 of 112

(7) EUT Photo

(8) EUT Photo


Page: 108 of 112

(9) EUT Photo

(10) EUT Photo


Page: 109 of 112

(11) EUT Photo

(12) EUT Photo


Page: 110 of 112

(13) EUT Photo

(14) EUT Photo


Page: 111 of 112

(15) EUT Photo

(16) EUT Photo


Page: 112 of 112

(17) EUT Photo