Upload
others
View
51
Download
0
Embed Size (px)
Citation preview
1
The Everyday Pocket Handbook for Visual Inspection of AWS D1.1 Structural Welding Code's Fabrication and Welding Requirements
2
NOTE: Although care was taken in choosing and presenting the data in this guide, AWS cannot guarantee that it is
error free. Further, this guide is not intended to be an exhaustive treatment of the topic and therefore may not include all
available information, including with respect to safety and health issues. By publishing this guide, AWS does not insure
anyone using the information it contains against any liability or injury to property or persons arising from that use.
© 2004 by American Welding Society. All rights reserved.Printed in the United States of America
4
Requirements for Transitions Between Materials of Unequal Thickness.............................................................. 5
Thermal Cutting and Access Hole Requirements .................................................................................................. 9
Tolerance of Joint Dimensions............................................................................................................................. 13
Dimensional Tolerances of Welded Structural Members..................................................................................... 19
Base Material Surface Requirements ................................................................................................................... 25
Weld Profile Requirements .................................................................................................................................. 26
Acceptance Criteria for Visual Inspection of Welds ............................................................................................ 32
Index..................................................................................................................................................................... 37
Table of Contents
5
Figure 2.21—Transition of Thickness of Butt Joints in Parts ofUnequal Thickness (Tubular) (see 2.25 [pg. 22])
Requirements for Transitions Between Materials of Unequal Thickness
5/pg. 55
6
Figure 2.21 (Cont’d)—Transition of Thickness of Butt Joints in Parts ofUnequal Thickness (Tubular) (see 2.25 [pg. 22])
Requirements for Transitions Between Materials of Unequal Thickness
6/pg. 55
7
Figure 2.2—Transition of Butt Joints in Parts of Unequal Thickness (Nontubular)(see 2.7.1 [pg. 10] and 2.16.1.1 [pg. 14])
Requirements for Transitions Between Materials of Unequal Thickness
7/pg. 42
8
Figure 2.12—Transition of Width (Cyclically Loaded Nontubular) (see 2.16.1.2 [pg. 14])
Requirements for Transitions Between Materials of Unequal Thickness
8/pg. 48
9
5.15.4.3 Roughness Requirements. In thermalcutting, the equipment shall be so adjusted andmanipulated as to avoid cutting beyond (inside) theprescribed lines. The roughness of all thermal cutsurfaces shall be no greater than that defined by theAmerican National Standards Institute surface rough-ness value of 1000 μin. [25 μm] for material up to4 in. [100 mm] thick and 2000 μin. [50 μm] for mate-rial 4 in. to 8 in. [200 mm] thick, with the followingexception: the ends of members not subject to calcu-lated stress at the ends shall not exceed a surfaceroughness value of 2000 μin. ANSI/ASME B46.1,Surface Texture (Surface Roughness, Waviness, andLay) is the reference standard. AWS Surface Rough-ness Guide for Oxygen Cutting (AWS C4.1-77) maybe used as a guide for evaluating surface roughnessof these edges. For materials up to and including 4 in.[100 mm] thick, Sample No. 3 shall be used, andfor materials over 4 in. up to 8 in. [200 mm] thick,Sample No. 2 shall be used.
5.15.4.4 Gouge or Notch Limitations. Rough-ness exceeding these values and notches or gougesnot more than 3/16 in. [5 mm] deep on other wisesatisfactory surfaces shall be removed by machiningor grinding. Notches or gouges exceeding 3/16 in.[5 mm] deep may be repaired by grinding if thenominal cross-sectional area is not reduced by morethan 2%. Ground or machined surfaces shall be faredto the original surface with a slope not exceeding onein ten. Cut surfaces and adjacent edges shall be leftfree of slag. In thermal-cut surfaces, occasionalnotches or gouges may, with approval of the Engi-neer, be repaired by welding.
5.16 Reentrant Corners
Reentrant corners of cut material shall be formedto provide a gradual transition with a radius of notless than 1 in. [25 mm]. Adjacent surfaces shall meetwithout offset or cutting past the point of tangency.
Thermal Cutting and Access Hole Requirements
9/pg. 185
10
The reentrant corners may be formed by thermal cut-ting, followed by grinding, if necessary, to meet thesurface requirements of 5.15.4.3.
5.17 Beam Copes and Weld Access Holes
Radii of beam copes and weld access holesshall provide a smooth transition free of notches orcutting past the points of tangency between adjacentsurfaces and shall meet the surface requirements of5.15.4.3.
5.17.1 Weld Access Hole Dimensions. All weld ac-cess holes required to facilitate welding operationsshall have a length ( ) from the toe of the weldpreparation not less than 1-1/2 times the thickness ofthe material in which the hole is made. The height(h) of the access hole shall be adequate for depo-sition of sound weld metal in the adjacent plates andprovide clearance for weld tabs for the weld in the
material in which the hole is made, but not less thanthe thickness of the material. In hot rolled shapes andbuilt-up shapes, all beam copes and weld accessholes shall be shaped free of notches or sharp re-entrant corners except that when fillet web-to-flangewelds are used in built-up shapes, access holes mayterminate perpendicular to the flange. Fillet weldsshall not be returned through weld access holes (seeFigure 5.2).
5.17.2 Group 4 and 5 Shapes. For ASTM A6Group 4 and 5 shapes and built-up shapes with webmaterial thickness greater than 1-1/2 in. [40 mm], thethermally cut surfaces of beam copes and weld accessholes shall be ground to bright metal and inspectedby either MT or PT. If the curved transition portion ofweld access holes and beam copes are formed by pre-drilled or sawed holes, that portion of the access holeor cope need not be ground. Weld access holes andbeam copes in other shapes need not be ground norinspected by MT or PT.
10/pg. 185
11
Figure 5.2—Weld Access Hole Geometry (see 5.17.1 [pg. 185])
11/pg. 196
12
General Notes:For ASTM A 6 Group 4 and 5 shapes and welded built-up shapes with web thickness more than 1-1/2 in. [40 mm], preheat to150°F [65°C] prior to thermal cutting, grind and inspect thermally cut edges of access hole using MT or PT methods prior tomaking web and flange splice groove welds.These are typical details for joints welded from one side against steel backing. Alternative joint designs should be considered.
Notes:1. Radius shall provide smooth notch-free transition; R ≥ 3/8 in. [10 mm] (Typical 1/2 in. [12 mm]).2. Access hole made after welding web to flange.3. Access hole made before welding web to flange. Weld not returned through hole.4. hmin = 3/4 in. [20 mm] or tw (web thickness), whichever is greater.
Figure 5.2 (Cont’d)—Weld Access Hole Geometry (see 5.17.1 [pg. 185])
12/pg. 196
13
5.22.1 Fillet Weld Assembly. The parts to be joined
by fillet welds shall be brought into as close contact as
practicable. The root opening shall not exceed 3/16 in.
[5 mm] except in cases involving either shapes or
plates 3 in. [75 mm] or greater in thickness if, after
straightening and in assembly, the root opening cannot
be closed sufficiently to meet this tolerance. In such
cases, a maximum root opening of 5/16 in. [8 mm]
may be used, provided suitable backing is used. Back-
ing may be of flux, glass tape, iron powder, or similar
materials, or welds using a low-hydrogen process
compatible with the filler metal deposited. If the sepa-
ration is greater than 1/16 in. [2 mm], the leg of the
fillet weld shall be increased by the amount of the root
opening, or the contractor shall demonstrate that the
required effective throat has been obtained.
5.22.1.1 Faying Surface. The separation be-
tween faying surfaces of plug and slot welds, and
of butt joints landing on a backing, shall not exceed
1/16 in. [2 mm]. Where irregularities in rolled shapes
occur after straightening do not allow contact within
the above limits, the procedure necessary to bring the
material within these limits shall be subject to the
approval of the Engineer. The use of filler plates shall
be prohibited except as specified on the drawings or
as specially approved by the Engineer and made in
accordance with 2.13.
5.22.2 PJP Groove Weld Assembly. The parts to be
joined by PJP groove welds parallel to the length of
the member shall be brought into as close contact as
practicable. The root opening between parts shall not
exceed 3/16 in. [5 mm] except in cases involving
rolled shapes or plates 3 in. [75 mm] or greater in
thickness if, after straightening and in assembly, the
root opening cannot be closed sufficiently to meet this
tolerance. In such cases, a maximum root opening of
5/16 in. [8 mm] may be used, provided suitable back-
ing is used and the final weld meets the requirements
Tolerance of Joint Dimensions
13/pg. 187
14
for weld size. Tolerances for bearing joints shall be inconformance with the applicable contract specifications.
5.22.3 Butt Joint Alignment. Parts to be joined atbutt joints shall be carefully aligned. Where the partsare effectively restrained against bending due toeccentricity in alignment, the offset from the theoreti-cal alignment shall not exceed 10% of the thicknessof the thinner part joined, or 1/8 in. [3 mm], which-ever is smaller. In correcting misalignment in suchcases, the parts shall not be drawn in to a greaterslope than 1/2 in. [12 mm] in 12 in. [300 mm]. Mea-surement of offset shall be based upon the centerlineof parts unless otherwise shown on the drawings.
5.22.3.1 Girth Weld Alignment (Tubular).Abutting parts to be joined by girth welds shall becarefully aligned. No two girth welds shall be locatedcloser than one pipe diameter or 3 ft [1 m], whicheveris less. There shall be no more than two girth welds inany 10 ft [3 m] interval of pipe, except as may beagreed upon by the Owner and Contractor. Radialoffset of abutting edges of girth seams shall notexceed 0.2t (where t is the thickness of the thinner
member) and the maximum allowable shall be 1/4 in.[6 mm], provided that any offset exceeding 1/8 in.[3 mm] is welded from both sides. However, withthe approval of the Engineer, one localized area pergirth seam may be offset up to 0.3t with a maximumof 3/8 in. [10 mm], provided the localized area isunder 8t in length. Filler metal shall be added to thisregion to provide a 4 to 1 transition and may be addedin conjunction with making the weld. Offsets inexcess of this shall be corrected as provided in 5.22.3.Longitudinal weld seams of adjoining sections shallbe staggered a minimum of 90°, unless closer spacingis agreed upon by the Owner and Fabricator.
5.22.4 Groove Dimensions
5.22.4.1 Nontubular Cross-Sectional Variations.With the exclusion of ESW and EGW, and with theexception of 5.22.4.3 for root openings in excess ofthose permitted in Figure 5.3, the dimensions of thecross section of the groove welded joints which varyfrom those shown on the detail drawings by morethan these tolerances shall be referred to the Engineerfor approval or correction.
14/pg. 187
15
5.22.4.2 Tubular Cross-Sectional Variations.Variation in cross section dimension of groove weldedjoints, from those shown on the detailed drawings,shall be in accordance with 5.22.4.1 except:
(1) Tolerances for T-, Y-, and K-connections areincluded in the ranges given in 3.13.4.
(2) The tolerances shown in Table 5.5 apply toCJP tubular groove welds in butt joints, made fromone side only, without backing.
5.22.4.3 Correction. Root openings greater thanthose permitted in 5.22.4.1, but not greater than twicethe thickness of the thinner part or 3/4 in. [20 mm],
whichever is less, may be corrected by welding toacceptable dimensions prior to joining the parts bywelding.
5.22.4.4 Engineer’s Approval. Root openingsgreater than allowed by 5.22.4.3 may be corrected bywelding only with the approval of the Engineer.
5.22.5 Gouged Grooves. Grooves produced bygouging shall be in substantial conformance withgroove profile dimensions as specified in Figure 3.3and 3.4 and provisions of 3.12.3 and 3.13.1. Suitableaccess to the root shall be maintained.
15/pgs. 187–188
16
Figure 5.3—Workmanship Tolerances in Assembly of Groove Welded Joints (see 5.22.4.1 [pg. 187])
16/pg. 197
17
Root NotBackgouged
RootBackgouged
in. mm in. mm
(1) Root face of joint ±1/16 2 Not limited
(2) Root opening of joints without backing
±1/16 2 +1/16–1/80
23
Root opening of joints with backing
+1/40–1/16
62 Not applicable
(3) Groove angle of joint
+10°–5°0
+10°–5°0
General Note: See 5.22.4.2 for tolerances for CJPtubular groove welds made from one side withoutbacking.
Figure 5.3 (Cont’d)—Workmanship Tolerances in Assembly of Groove Welded Joints (see 5.22.4.1 [pg. 187])
17/pg. 197
18
Table 5.5Tubular Root Opening Tolerances (see 5.22.4.2 [pg. 187])
Root Face of JointRoot Opening of Joints without Steel Backing
Groove Angleof Joint
in. mm in. mm deg
SMAWGMAWFCAW
±1/16±1/32±1/16
±2±1±2
±1/16±1/16±1/16
±2±2±2
±5±5±5
General Note: Root openings wider than allowed by the above tolerances, but not greater than the thickness of the thinner part,may be built up by welding to acceptable dimensions prior to the joining of the parts by welding.
18/pg. 194
19
5.23 Dimensional Tolerances of Welded Structural Members
The dimensions of welded structural membersshall conform to the tolerances of (1) the generalspecifications governing the work, and (2) the specialdimensional tolerances in 5.23.1 to 5.23.11.3. (Notethat a tubular column is interpreted as a compressiontubular member.)
5.23.1 Straightness of Columns and Trusses. Forwelded columns and primary truss members, regard-less of cross section, the maximum variation instraightness shall be
Lengths of less than 30 ft [9 m]:
1 mm × No. of meters of total length
Lengths of 30 ft [10 m] to 45 ft [14 m] = 3/8 in. [10 mm]
Lengths over 45 ft [15 m]:
5.23.2 Beam and Girder Straightness (No Cam-ber Specified). For welded beams or girders, regard-less of cross section, where there is no specifiedcamber, the maximum variation in straightness shallbe
1 mm × No. of meters of total length
5.23.3 Beam and Girder Camber (TypicalGirder). For welded beams or girders, other thanthose whose top flange is embedded in concrete with-out a designed concrete haunch, regardless of cross
1/8 in.No. of ft of total length
10-------------------------------------------------------×
3/8 in. + 1/8 in.No. of ft of total length – 45
10---------------------------------------------------------------------×
10 mm + 3 mmNo. of meters of total length – 15
3--------------------------------------------------------------------------------×
1/8 in.No. of ft of total length
10-------------------------------------------------------×
Dimensional Tolerances of Welded Structural Members
19/pg. 188
20
section, the maximum variation from required cam-ber at shop assembly (for drilling holes for fieldsplices or preparing field welded splices) shall be
at midspan, – 0, +1-1/2 in. [40 mm] for spans ≥ 100 ft
[30 m]
– 0, + 3/4 in. [20 mm] for spans < 100 ft
[30 m]
at supports, 0 for end supports
± 1/8 [3 mm] for interior supports
at intermediate points, –0, +
where
a = distance in feet [meters] from inspectionpoint to nearest support
S = span length in feet [meters]
b = 1-1/2 in. [40 mm] for spans ≥ 100 ft [30 m]
b = 3/4 in. [20 mm] for spans < 100 ft [30 m]
See Table 5.6 for tabulated values.
5.23.4 Beam and Girder Camber (withoutDesigned Concrete Haunch). For members whose
top flange is embedded in concrete without adesigned concrete haunch, the maximum variationfrom required camber at shop assembly (for drillingholes for field splices or preparing field weldedsplices) shall be
at midspan, ± 3/4 in. [20 mm] for spans ≥ 100 ft
[30 m]
± 3/8 in. [10 mm] for spans < 100 ft
[30 m]
at supports, 0 for end supports
± 1/8 in. [3 mm] for interior supports
at intermediate points, ±
where a and S are as defined above
b = 3/4 in. [20 mm] for spans ≥ 100 ft [30 m]
b = 3/8 in. [10 mm] for spans < 100 ft [30 m]
See Table 5.7 for tabulated values.
Regardless of how the camber is shown on the detaildrawings, the sign convention for the allowable vari-ation is plus (+) above, and minus (–) below, the
4(a)b(1 – a/S)
S---------------------------------
4(a)b(1 – a/S)
S---------------------------------
20/pgs. 188–189
21
Table 5.6Camber Tolerancefor Typical Girder
(see 5.23.3 [pg. 188–189])
Camber Tolerance (in inches)
a/SSpan 0.1 0.2 0.3 0.4 0.5
≥ 100 ft 9/16 1 1-1/4 1-7/16 1-1/2
< 100 ft 1/4 1/2 5/8 3/4 3/4
Camber Tolerance (in millimeters)
a/SSpan 0.1 0.2 0.3 0.4 0.5
≥ 30 m 14 25 34 38 40
< 30 m 7 13 17 19 20
Table 5.7Camber Tolerance for Girders
without a Designed Concrete Haunch (see 5.23.4 [pg. 188–189])
Camber Tolerance (in inches)
a/SSpan 0.1 0.2 0.3 0.4 0.5
≥ 100 ft 1/4 1/2 5/8 3/4 3/4
< 100 ft 1/8 1/4 5/16 3/8 3/8
Camber Tolerance (in millimeters)
a/SSpan 0.1 0.2 0.3 0.4 0.5
≥ 30 m 7 13 17 19 20
< 30 m 4 6 8 10 10
21/pg. 194
22
detailed camber shape. These provisions also applyto an individual member when no field splices orshop assembly is required. Camber measurementsshall be made in the no-load condition.
5.23.5 Beam and Girder Sweep. The maximumvariation in specified sweep at the midpoint shall be
1 mm × No. of meters of total length
provided the member has sufficient lateral flexibilityto permit the attachment of diaphragms, cross-frames, lateral bracing, etc., without damaging thestructural member or its attachments.
5.23.6 Variation in Web Flatness
5.23.6.1 Measurements. Variations from flatnessof girder webs shall be determined by measuring theoffset from the actual web centerline to a straightedge whose length is greater than the least paneldimension and placed on a plane parallel to the nomi-
nal web plane. Measurements shall be taken prior toerection (see Commentary).
5.23.6.2 Statically Loaded Nontubular Struc-tures. Variations from flatness of webs having adepth, D, and a thickness, t, in panels bounded bystiffeners or flanges, or both, whose least paneldimension is d shall not exceed the following:
Intermediate stiffeners on both sides of webwhere D/t < 150, maximum variation = d/100where D/t ≥ 150, maximum variation = d/80
Intermediate stiffeners on one side only of webwhere D/t < 100, maximum variation = d/100where D/t ≥ 100, maximum variation = d/67
No intermediate stiffenerswhere D/t ≥ 100, maximum variation = D/150
(See Annex VI for tabulation.)
5.23.6.3 Cyclically Loaded Nontubular Struc-tures. Variation from flatness of webs having adepth, D, and a thickness, t, in panels bounded bystiffeners or flanges, or both, whose least paneldimension is d shall not exceed the following:
1/8 in.No. of feet of total length
10-------------------------------------------------------------×±
22/pg. 189
23
Intermediate stiffeners on both sides of web
Interior girders—
where D/t < 150—maximum variation = d/115
where D/t ≥ 150—maximum variation = d/92
Fascia girders—
where D/t < 150—maximum variation = d/130
where D/t ≥ 150—maximum variation = d/105
Intermediate stiffeners on one side only of web
Interior girders—
where D/t < 100—maximum variation = d/100
where D/t ≥ 100—maximum variation = d/67
Fascia girders—
where D/t < 100—maximum variation = d/120
where D/t ≥ 100—maximum variation = d/80
No intermediate stiffeners—maximum variation = D/150
(See Annex VII for tabulation.)
5.23.6.4 Excessive Distortion. Web distortions oftwice the allowable tolerances of 5.23.6.2 or 5.23.6.3shall be satisfactory when occurring at the end of agirder which has been drilled, or subpunched and
reamed; either during assembly or to a template for afield bolted splice; provided, when the splice platesare bolted, the web assumes the proper dimensionaltolerances.
5.23.6.5 Architectural Consideration. If archi-tectural considerations require tolerances morerestrictive than described in 5.23.6.2 or 5.23.6.3, spe-cific reference must be included in the bid documents.
5.23.7 Variation Between Web and Flange Center-
lines. For built-up H or I members, the maximumvariation between the centerline of the web and thecenterline of the flange at contact surface is 1/4 in.[6 mm].
5.23.8 Flange Warpage and Tilt. For welded beamsor girders, the combined warpage and tilt of flangeshall be determined by measuring the offset at the toeof the flange from a line normal to the plane of theweb through the intersection of the centerline of theweb with the outside surface of the flange plate. Thisoffset shall not exceed 1% of the total flange widthor 1/4 in. [6 mm], whichever is greater, except that
23/pg. 189
24
welded butt joints of abutting parts shall fulfill therequirements of 5.22.3.
5.23.9 Depth Variation. For welded beams andgirders, the maximum allowable variation from spec-ified depth measured at the web centerline shall be
For depths up to 36 in. [1 m] incl. ± 1/8 in. [3 mm]For depths over 36 in. [1 m] to
72 in. [2 m] incl. ± 3/16 in. [5 mm]For depths over 72 in. [2 m] + 5/16 in. [8 mm]
– 3/16 in. [5 mm]
5.23.10 Bearing at Points of Loading. The bearingends of bearing stiffeners shall be square with the weband shall have at least 75% of the stiffener bearingcross-sectional area in contact with the inner surface ofthe flanges. The outer surface of the flanges whenbearing against a steel base or seat shall fit within0.010 in. [0.25 mm] for 75% of the projected area ofweb and stiffeners and not more than 1/32 in. [1 mm]for the remaining 25% of the projected area. Girderswithout stiffeners shall bear on the projected area ofthe web on the outer flange surface within 0.010 in.[0.25 mm] and the included angle between web and
flange shall not exceed 90° in the bearing length (see
Commentary).
5.23.11 Tolerance on Stiffeners
5.23.11.1 Fit of Intermediate Stiffeners. Where
tight fit of intermediate stiffeners is specified, it shall
be defined as allowing a gap of up to 1/16 in.
[1.6 mm] between stiffener and flange.
5.23.11.2 Straightness of Intermediate Stiffen-
ers. The out-of-straightness variation of intermediate
stiffeners shall not exceed 1/2 in. [12 mm] for girders
up to 6 ft [1.8 m] deep, and 3/4 in. [20 mm] for
girders over 6 ft [1.8 m] deep, with due regard for
members which frame into them.
5.23.11.3 Straightness and Location of Bearing
Stiffeners. The out-of-straightness variation of bear-
ing stiffeners shall not exceed 1/4 in. [6 mm] up to
6 ft [1.8 m] deep or 1/2 in. [12 mm] over 6 ft [1.8 m]
deep. The actual centerline of the stiffener shall lie
within the thickness of the stiffener as measured from
the theoretical centerline location.
24/pgs. 89–190
25
5.23.11.4 Other Dimensional Tolerances. Twist
of box members and other dimensional tolerances of
members not covered by 5.23 shall be individually
determined and mutually agreed upon by the Con-
tractor and the Owner with proper regard for erection
requirements.
5.15 Preparation of Base Metal
Surfaces on which weld metal is to be depositedshall be smooth, uniform, and free from fins, tears,cracks, and other discontinuities which wouldadversely affect the quality or strength of the weld.Surfaces to be welded, and surfaces adjacent to aweld, shall also be free from loose or thick scale,slag, rust, moisture, grease, and other foreign mate-rial that would prevent proper welding or produceobjectionable fumes. Mill scale that can withstandvigorous wire brushing, a thin rust-inhibitive coating,
or antispatter compound may remain with thefollowing exception: for girders in cyclically loadedstructures, all mill scale shall be removed from thesurfaces on which flange-to-web welds are to bemade.
5.29 Arc Strikes
Arc strikes outside the area of permanent weldsshould be avoided on any base metal. Cracks orblemishes caused by arc strikes shall be ground to asmooth contour and checked to ensure soundness.
Base Material Surface Requirements
25/pgs. 184; 192
pg. 190
26
5.24 Weld Profiles
All welds, except as otherwise permitted below,shall be free from cracks, overlaps, and the unaccept-able profile discontinuities exhibited in Figure 5.4.
5.24.1 Fillet Welds. The faces of fillet welds may beslightly convex, flat, or slightly concave as shown inFigure 5.4. Figure 5.4(C) shows typically unaccept-able fillet weld profiles.
5.24.2 Exception for Intermittent Fillet Welds.Except for undercut, as allowed by the code, the pro-file requirements of Figure 5.4 shall not apply to theends of intermittent fillet welds outside their effectivelength.
5.24.3 Convexity. Except at outside welds in cornerjoints, the convexity C of a weld or individual surfacebead shall not exceed the values given in Figure 5.4.
5.24.4 Groove or Butt Welds. Groove welds shallbe made with minimum face reinforcement unlessotherwise specified. In the case of butt and corner
joints, face reinforcement shall not exceed 1/8 in.[3 mm] in height. All welds shall have a gradual tran-sition to the plane of the base-metal surfaces withtransition areas free from undercut except as allowedby this code. Figure 5.4(D) shows typically accept-able groove weld profiles in butt joints. Figure 5.4(E)shows typically unacceptable weld profiles forgroove weld butt joints.
5.24.4.1 Flush Surfaces. Butt welds required tobe flush shall be finished so as to not reduce thethicknesses of the thinner base metal or weld metalby more than 1/32 in. [1 mm], or 5% of the materialthickness, whichever is less. Remaining reinforce-ment shall not exceed 1/32 in. [1 mm] in height.However, all reinforcement shall be removed wherethe weld forms part of a faying or contact surface. Allreinforcement shall blend smoothly into the plate sur-faces with transition areas free from undercut.
5.24.4.2 Finish Methods and Values. Chipping andgouging may be used provided these are followed by
Weld Profile Requirements
26/pg. 190
27
grinding. Where surface finishing is required, roughnessvalues (see ASME B46.1) shall not exceed250 microinches [6.3 micrometers]. Surfaces finishedto values of over 125 microinches [3.2 micrometers]
through 250 microinches [6.3 micrometers] shall be fin-ished parallel to the direction of primary stress. Surfacesfinished to values of 125 microinches [3.2 micrometers]or less may be finished in any direction.
Figure 5.4—Acceptable and Unacceptable Weld Profiles (see 5.24 [pg. 190])
27/pg. 198
pg. 190
28
Figure 5.4 (Cont’d)—Acceptable and Unacceptable Weld Profiles (see 5.24 [pg. 190])
28/pg. 198
29
Figure 5.4 (Cont’d)—Acceptable and Unacceptable Weld Profiles (see 5.24 [pg. 190])
29/pg. 198
30
Table 5.8Minimum Fillet Weld Size (see 5.14 [pg. 183])
Base Metal Thickness (T)1 Minimum Size of Fillet Weld2
in. mm in. mm
T ≤ 1/4 T ≤ 61/8
(Note 3)3
(Note 3)
1/4 < T ≤ 1/2 6 < T ≤ 12 3/16 5
1/2 < T ≤ 3/4 12 < T ≤ 20 1/4 6
3/4 < T 20 < T 5/16 8
Notes:1. For non-low-hydrogen processes without preheat calculated in accordance with 3.5.2, T equals thickness of the thicker part
joined; single-pass welds shall be used.For non-low-hydrogen processes using procedures established to prevent cracking in accordance with 3.5.2 and for low-hydrogen processes, T equals thickness of the thinner part joined; single-pass requirement does not apply.
2. Except that the weld size need not exceed the thickness of the thinner part joined.3. Minimum size for cyclically loaded structures is 3/16 in. [5 mm].
30/pg. 194
31
Figure 2.1—Maximum Fillet Weld SizeAlong Edges in Lap Joints (see 2.3.2.9 [pg. 7])
31/pg. 41
32
Table 6.1Visual Inspection Acceptance Criteria (see 6.9 [pg. 201])
Discontinuity Category and Inspection Criteria
Statically Loaded
NontubularConnections
Cyclically Loaded
NontubularConnections
Tubular Connections (All Loads)
(1) Crack ProhibitionAny crack shall be unacceptable, regardless of size or location.
X X X
(2) Weld/Base-Metal FusionThorough fusion shall exist between adjacent layers of weld metal and between weld metal and base metal.
X X X
(3) Crater Cross SectionAll craters shall be filled to provide the specified weld size, except for the ends of intermittent fillet welds outside of their effective length.
X X X
(4) Weld ProfilesWeld profiles shall be in conformance with 5.24.
X X X
Acceptance Criteria for Visual Inspection of Welds
32/pg. 218
33
(5) Time of InspectionVisual inspection of welds in all steels may begin immediately after the completed welds have cooled to ambient temperature. Acceptance criteria for ASTM A 514, A 517, and A 709 Grade 100 and 100 W steels shall be based on visual inspection performed not less than 48 hours after completion of the weld.
X X X
(6) UnderrunThe size of a fillet weld in any continuous weld may be less than the spec-ified nominal size (L) without correction by the following amounts (U):
L, specified U, allowablenominal weld size, in. [mm] decrease from L, in. [mm]
≤ 3/16 [5] ≤ 1/16 [2]≤ 1/4 [6] .0 ≤ 3/32 [2.5]≤ 5/16 [8] ≤ 1/8 [3]
X X X
Table 6.1 (Continued)Visual Inspection Acceptance Criteria (see 6.9 [pg. 201])
Discontinuity Category and Inspection Criteria
Statically Loaded
NontubularConnections
Cyclically Loaded
NontubularConnections
Tubular Connections (All Loads)
33/pg. 218
34
(6) Underrun (Cont’d)In all cases, the undersize portion of the weld shall not exceed 10% of the weld length. On web-to-flange welds on girders, underrun shall beprohibited at the ends for a length equal to twice the width of the flange.
X X
(7) Undercut(A) For material less than 1 in. [25 mm] thick, undercut shall not exceed 1/32 in. [1 mm], with the following exception: undercut shall not exceed except that a maximum 1/16 in. [2 mm] for any accumulated length up to 2 in. [50 mm] in any 12 in. [300 mm]. For material equal to or greater than 1 in. thick, undercut shall not exceed 1/16 in. [2 mm] for any length of weld.
X
Table 6.1 (Continued)Visual Inspection Acceptance Criteria (see 6.9 [pg. 201])
Discontinuity Category and Inspection Criteria
Statically Loaded
NontubularConnections
Cyclically Loaded
NontubularConnections
Tubular Connections (All Loads)
34/pg. 218
35
(7) Undercut (Cont’d)(B) In primary members, undercut shall be no more than 0.01 in. [0.25 mm] deep when the weld is transverse to tensile stress under any design loading condition. Undercut shall be no more than 1/32 in. [1 mm] deep for all other cases.
X X
(8) Porosity(A) CJP groove welds in butt joints transverse to the direction of com-puted tensile stress shall have no visible piping porosity. For all other groove welds and for fillet welds, the sum of the visible piping porosity 1/32 in. [1 mm] or greater in diameter shall not exceed 3/8 in. [10 mm] in any linear inch of weld and shall not exceed 3/4 in. [20 mm] in any 12 in. [300 mm] length of weld.
X
Table 6.1 (Continued)Visual Inspection Acceptance Criteria (see 6.9 [pg. 201])
Discontinuity Category and Inspection Criteria
Statically Loaded
NontubularConnections
Cyclically Loaded
NontubularConnections
Tubular Connections (All Loads)
35/pg. 218
36
(8) Porosity (Cont’d)(B) The frequency of piping porosity in fillet welds shall not exceed one in each 4 in. [100 mm] of weld length and the maximum diameter shall not exceed 3/32 in. [2.5 mm]. Exception: for fillet welds connect-ing stiffeners to web, the sum of the diameters of piping porosity shall not exceed 3/8 in. [10 mm] in any linear inch of weld and shall not exceed 3/4 in. [20 mm] in any 12 in. [300 mm] length of weld.
X X
(C) CPP groove welds in butt joints transverse to the direction of computed tensile stress shall have no piping porosity. For all other groove welds, the frequency of piping porosity shall not exceed onein 4 in. [100 mm] of length and the maximum diameter shall not exceed 3/32 in. [2.5 mm].
X X
General Note: An “X” indicates applicability for the connection type; a shaded area indicates non-applicability.
Table 6.1 (Continued)Visual Inspection Acceptance Criteria (see 6.9 [pg. 201])
Discontinuity Category and Inspection Criteria
Statically Loaded
NontubularConnections
Cyclically Loaded
NontubularConnections
Tubular Connections (All Loads)
36/pg. 218
3
The inspection requirements for the fabrication and welding of steel structures are very extensive. This PocketHandbook has been developed to provide a useful tool for inspectors to carry in their pockets or tool kits sothat selected pertinent portions of the AWS Structural Welding Code—Steel, D1.1/D1.1M:2004, can be easilyreferenced at the job site. Underlining is as shown in the code.
This publication is not to be considered as a substitute for the D1.1 code book. Rather, the Handbook is providedas a supplemental aid for the “deckplate” inspector. Only the complete code should be considered as the officialdocument to ensure that all of the quality attributes required for structural fabrication are performed correctlyand completely.
To assist the inspector, or other user, in verifying conformance to D1.1, the paragraph references, the table num-bers, and the figure numbers contained in this book are directly from the D1.1/D1.1M:2004 code. In addition,page numbering in this handbook is cross-referenced to reflect both the current page and the corresponding pagefrom the D1.1/D1.1M:2004 code, separated by a “/.” This will provide an easy cross reference for the user toensure that the complete requirements are understood when questions develop during the course of any inspection.
Introduction
INDEX
Index Terms Links
A Acceptance Criteria for Visual Inspection of Welds 32
B Base Material Surface Requirements
Preparation of Base Metal 25
Arc Strikes 25
This page has been reformatted by Knovel to provide easier navigation.
Index Terms Links
Beam Copes and Weld Access Holes
Weld Access Hole Dimensions 10
Group 4 and 5 Shapes 10
D Dimensional Tolerances of Welded Structural Members
Straightness of Columns and Trusses 19
Beam and Girder Straightness 19
Beam and Girder Camber 20
This page has been reformatted by Knovel to provide easier navigation.
Index Terms Links
Dimensional Tolerances of Welded Structural Members (Cont.)
Beam and Girder Sweep 22
Variation in Web Flatness 22
Variation Between Web and Flange Centerline 23
Flange Warpage and Tilt 23
Depth Variation 24
Bearing and Points of Loading 24
Tolerance on Stiffeners 24
This page has been reformatted by Knovel to provide easier navigation.
Index Terms Links
T Thermal Cutting
Roughness Requirements 9
Gouge or Notch Limitations 9
Reentrant Corners 9
Tolerance of Joint Dimensions
Fillet Weld Assembly 13
Faying Surfaces 13
This page has been reformatted by Knovel to provide easier navigation.
Index Terms Links
Tolerance of Joint Dimensions (Cont.)
PJP Groove Weld Assembly 13
Butt Joint Alignment 14
Girth Weld Alignment (Tubular). 14
Groove Dimensions (Nontubular). 14
Groove Dimensions (Tubular). 15
Corrections of Groove Dimensions 15
Gouged Grooves 15
This page has been reformatted by Knovel to provide easier navigation.
Index Terms Links
Transitions Between Materials of Unequal Thickness
Tubular 5
Nontubular 7
Width Nontubular 8
W Weld Profile Requirements
Fillet Welds 26
Exception for Intermittent Fillet Welds 26
This page has been reformatted by Knovel to provide easier navigation.
Index Terms Links
Weld Profile Requirements (Cont.)
Convexity 26
Groove or Butt Welds 26
Flush Surfaces 26
Finish Methods and Values 26
Minimum Fillet Weld Size 30
This page has been reformatted by Knovel to provide easier navigation.