Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
Final update suggestion document
THE GHOST S1
THE GHOST S1
Suggested updatesAll the updates in this document add features or value in other ways to the Ghost S1 design, some affect cost negatively others decrees cost. The sum of all updates result in a small increase in manufacturing cost but this will not affect the price point of the product.
Below are the updates presented in table format, the rest of the document provides illustrations and descriptions of the updates.
Final update suggestion document
# Name Cost impact Status Area
1 3:rd PSU position Small increase Added to model Blade
2 Blade SSD Small increase Added to model Blade
3 Riser position None Added to model Blade
4 Added zip ties Small increase Added to model Blade
5 Bottom plate clean up Small decrease Added to model Bottom plate
6 C14 Small increase Added to model C14 power connector
7 New SSD tray Small increase Added to model Disk tray
8 FTW3 adjustment Small increase Added to model Gable [BACK]
9 Kensington Small increase Added to model Gable [BACK]
10 Rear symmetry Small decrease Added to model Gable [BACK]
11 GPU max height increase None Added to model Gable [BACK]
12 Gable spline Small increase Added to model Gable [BOTH]
13 OI symmetry Small decrease Added to model Gable [FRONT]
14 GPU cover Small decrease Added to model GPU bracket
15 Rag tag opening None Added to model Grill
16 Grill hole pattern Small increase Added to model Grill
17 Grill screw down Small increase Added to model Grill
18 Grill material Increase Added to model Grill
19 PSU bracket compatibility None Added to model PSU bracket
20 Cable management None Added to model PSU bracket
21 Screw harmonization Small decrease Added to model Screws
22 Side filter frame Small decrease Added to model Side panel
23 Side filter pickup Small increase Added to model Side panel
24 Slide interface None Added to model Side panel
25 Side spline Small increase Added to model Side panel
26 Top plate adjustments Small increase Added to model Top plate
27 TopHat countersinks Small increase Added to model TopHats
28 TopHat heights Small increase Added to model TopHats
THE GHOST S1
# 1
Add a third mounting option for PSU bracket, 15mm higher than the top position
Short description
Small increase
Production cost impact
Affected component
Blade
Status
Added to model, awaiting community feedback
# 2
Add SSD mounting holes behind the PSU
Short description
Small increase
Production cost impact
Affected component
Blade
Status
Added to model, awaiting community feedback
# 3
Lower PCI riser stand-offs position 2.54 mm
Short description
NONE
Production cost impact
Affected component
Blade
Status
Added to model, awaiting community feedback
# 4
Zip tie holes for water pipes in bottom position
Short description
Small increase
Production cost impact
Affected component
Blade
Status
Added to model, awaiting community feedback
Final update suggestion document
Name
3:rd PSU position
Name
Blade SSD
Name
Riser position
Name
Added zip ties
THE GHOST S1
# 5
Remove redundant SSD-bracket holes
Short description
Small decrease
Production cost impact
Affected component
Bottom plate
Status
Added to model, awaiting community feedback
# 6
C14 screw-in PWR contact instead of snap on
Short description
Small increase
Production cost impact
Affected component
C14 power connector
Status
Added to model, awaiting community feedback
# 7
Redesign to fit 120 mm mounting slots, creating flexibility to mount in TopHats
Short description
Small increase
Production cost impact
Affected component
Disk tray
Status
Added to model, awaiting community feedback
# 8
Milling on inside of top back corner needs to be increased ~1,5 mm for specific GPU to fit (FTW3)
Short description
Small increase
Production cost impact
Affected component
Gable [BACK]
Status
Added to model, awaiting community feedback
Final update suggestion document
Name
Bottom plate clean up
Name
C14
Name
New SSD tray
Name
FTW3 adjustment
THE GHOST S1
# 9
Kensington lock hole added below label
Short description
Small increase
Production cost impact
Affected component
Gable [BACK]
Status
Added to model, awaiting community feedback
#10
Adjust sticker to harmonize with other changes for visual symmetry
Short description
Small decrease
Production cost impact
Affected component
Gable [BACK]
Status
Added to model, awaiting community feedback
#11
Lowered GPU position by 2.54mm, increasing max GPU height to 145.5mm
Short description
NONE
Production cost impact
Affected component
Gable [BACK]
Status
Added to model, awaiting community feedback
#12
Increase side curvature to create a more solid impression (avoiding visual collapse) ~0.25 mm (spline)
Short description
Small increase
Production cost impact
Affected component
Gable [BOTH]
Status
Added to model, awaiting community feedback
Final update suggestion document
Name
Kensington
Name
Rear symmetry
Name
GPU max height increase
Name
Gable spline
THE GHOST S1
#13
Centered screw columns for Button circuit board
Short description
Small decrease
Production cost impact
Affected component
Gable [FRONT]
Status
Added to model, awaiting community feedback
#14
Slide down GPU covering plate on the inside
Short description
Small decrease
Production cost impact
Affected component
GPU bracket
Status
Added to model, awaiting community feedback
#15
Increase flag hole to 3.0mm in width for leather / woven ribbon fit
Short description
NONE
Production cost impact
Affected component
Grill
Status
Added to model, awaiting community feedback
#16
Hole pattern further to the sides, add one row and column + re-center
Short description
Small increase
Production cost impact
Affected component
Grill
Status
Added to model, awaiting community feedback
Final update suggestion document
Name
OI symmetry
Name
GPU cover
Name
Rag tag opening
Name
Grill hole pattern
THE GHOST S1
#17
Updated hole pattern allowing screws to reach the threaded holes in the gables and side sheets
Short description
Small increase
Production cost impact
Affected component
Grill
Status
Added to model, awaiting community feedback
#18
Stronger steel (spring steel)
Short description
Increase
Production cost impact
Affected component
Grill
Status
Added to model, awaiting community feedback
#19
Increase top opening size by 0.5 mm for better fit with PSUs that don’t follow standard (Silverstone)
Short description
NONE
Production cost impact
Affected component
PSU bracket
Status
Added to model, awaiting community feedback
#20
Remove material on blade side of the PSU bracket to create opening for cable routing, no routing prior to mounting will be needed this way
Short description
NONE
Production cost impact
Affected component
PSU bracket
Status
Added to model, awaiting community feedback
Final update suggestion document
Name
Grill screw down
Name
Grill material
Name
PSU bracket compatibility
Name
Cable management
THE GHOST S1
#21
Fewer screw length variations and all M3 black torx T10
Short description
Small decrease
Production cost impact
Affected component
Screws
Status
Added to model, awaiting community feedback
#22
Increase filter frame around ventilated area to 12 mm to be compatible with DEMCi, remove one column of holes and re-center
Short description
Small decrease
Production cost impact
Affected component
Side panel
Status
Added to model, awaiting community feedback
#23
Grip slot for easier dust filter pickup added
Short description
Small increase
Production cost impact
Affected component
Side panel
Status
Added to model, awaiting community feedback
#24
Updated sliding interface between side sheet and gables
Short description
NONE
Production cost impact
Affected component
Side panel
Status
Added to model, awaiting community feedback
Final update suggestion document
Name
Screw harmonization
Name
Side filter frame
Name
Side filter pickup
Name
Slide interface
THE GHOST S1
#25
Increase side curvature to create a more solid impression (avoiding visual collapse) ~0.25 mm (spline)
Short description
Small increase
Production cost impact
Affected component
Side panel
Status
Added to model, awaiting community feedback
#26
redesigned to match TopHat countersink
Short description
Small increase
Production cost impact
Affected component
Top plate
Status
Added to model, awaiting community feedback
#27
Countersinks for the platform to fall down deeper into the gables and not affect the TopHat alignment, all positions now have equal gap size
Short description
Small increase
Production cost impact
Affected component
TopHats
Status
Added to model, awaiting community feedback
#28
All sizes 1 mm taller
Short description
Small increase
Production cost impact
Affected component
TopHats
Status
Added to model, awaiting community feedback
Final update suggestion document
Name
Side spline
Name
Top plate adjustments
Name
TopHat countersinks
Name
TopHat heights